Datasets:
IAmSomeone
/
Windows_command

Dataset card Data Studio Files
xet
 Community
text
stringlengths
0
4.23k
computing statistics for 125 seconds...
Source to Here This Node/Link
Hop RTT Lost/Sent = Pct Lost/Sent = Pct address
0 172.16.87.35
0/ 100 = 0% |
1 41ms 0/ 100 = 0% 0/ 100 = 0% 172.16.87.218
13/ 100 = 13% |
2 22ms 16/ 100 = 16% 3/ 100 = 3% 192.168.52.1
0/ 100 = 0% |
3 24ms 13/ 100 = 13% 0/ 100 = 0% 192.168.80.1
0/ 100 = 0% |
4 21ms 14/ 100 = 14% 1/ 100 = 1% 10.54.247.14
0/ 100 = 0% |
5 24ms 13/ 100 = 13% 0/ 100 = 0% 10.54.1.196
Trace complete.
When pathping is run, the first results list the path. Next, a busy message is displayed for approximately 90 seconds (the time varies by hop count). During this time, information is gathered from all routers previously listed and from the links between them. At the end of this period, the test results are displayed.
In the above sample report, the This Node/Link, Lost/Sent = Pct and address columns show that the link between 172.16.87.218 and 192.168.52.1 is dropping 13% of the packets. The routers at hops 2 and 4 are also dropping packets addressed to them, but this loss doesn't affect their ability to forward traffic that isn't addressed to them.
The loss rates displayed for the links, identified as a vertical bar (|) in the address column, indicate link congestion that is causing the loss of packets that are being forwarded on the path. The loss rates displayed for routers (identified by their IP addresses) indicate that these routers might be overloaded.
pause
Suspends the processing of a batch program, displaying the prompt, Press any key to continue . . .
Press any key to continue . . .
Syntax
pause
Parameters
Parameter
Description
/?
Displays help at the command prompt.
Remarks
If you press CTRL+C to stop a batch program, the following message appears, Terminate batch job (Y/N)?. If you press Y (for yes) in response to this message, the batch program ends and control returns to the operating system.
Terminate batch job (Y/N)?
You can insert the pause command before a section of the batch file that you might not want to process. When pause suspends processing of the batch program, you can press CTRL+C and then press Y to stop the batch program.
Examples
To create a batch program that prompts the user to change disks in one of the drives, type:
@echo off
:Begin
copy a:*.*
echo Put a new disk into Drive A
pause
goto begin
In this example, all the files on the disk in Drive A are copied to the current directory. After the message prompts you to put a new disk in Drive A, the pause command suspends processing so that you can change disks and then press any key to resume processing. This batch program runs in an endless loop—the goto begin command sends the command interpreter to the Begin label of the batch file.
pbadmin
Applies to: Windows Server 2022, Windows Server 2019, Windows Server 2003, Windows Server 2003 R2, Windows Server 2003 with SP1, Windows Server 2003 with SP2
Important
This command has been deprecated.
Administers phone books. Used without parameters, pbadmin starts Phone Book Administrator. For descriptions and usage information, see pbadmin.
pentnt
Applies to: Windows Server 2022, Windows Server 2019, Windows Server 2003, Windows Server 2003 R2, Windows Server 2003 with SP1, Windows Server 2003 with SP2
Important
This command has been deprecated.
Detects floating point division error (if present) in the Pentium chip, disables floating point hardware, and turns on floating point emulation. For descriptions and usage information, see pentnt.
perfmon
Start Windows Reliability and Performance Monitor in a specific standalone mode.
Syntax
perfmon </res|report|rel|sys>
Parameters
Parameter
Description
/res
Starts the Resource View.
/report
Starts the System Diagnostics Data Collector Set and displays a report of the results.
/rel
Starts the Reliability Monitor.
/sys
Starts the Performance Monitor.
ping
Applies to: Windows Server 2022, Windows Server 2019, Windows Server 2016, Windows Server 2012 R2, Windows Server 2012
Verifies IP-level connectivity to another TCP/IP computer by sending Internet Control Message Protocol (ICMP) echo Request messages. The receipt of corresponding echo Reply messages are displayed, along with round-trip times. ping is the primary TCP/IP command used to troubleshoot connectivity, reachability, and name resolution. Used without parameters, this command displays Help content.
You can also use this command to test both the computer name and the IP address of the computer. If pinging the IP address is successful, but pinging the computer name isn't, you might have a name resolution problem. In this case, make sure the computer name you are specifying can be resolved through the local Hosts file, by using Domain Name System (DNS) queries, or through NetBIOS name resolution techniques.
Note
This command is available only if the Internet Protocol (TCP/IP) is installed as a component in the properties of a network adapter in Network Connections.