input stringclasses 1 value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立⑤",
"WorkItems": [
"2. 1.完成品にDOG をBOLT WASHER で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"出代:15mm"
]
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:15.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "10cN･m以下",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立⑥",
"WorkItems": [],
"WorkPoints": [
"回転ﾄﾙｸ 10cN･m以下 ﾊﾞﾗﾂｷ 3cN･m以下",
"ﾓｰﾀ取付側でﾎﾞｰﾙﾈｼﾞに倣わせて組付け",
"摺動が悪い場合は軸受側に寄せてﾎﾞﾙﾄを締めなおす"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-087",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:<Y軸> ﾎﾞｰﾙﾈｼﾞ回転ﾄﾙｸ (ﾓｰﾀｰ組込み前)",
"WWYJ-5300-087"
]
} | {
"QualityItem": "回転ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "回転ﾄﾙｸ10cN・m以下",
"Method": "ﾄﾙｸｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "10cN･m以下",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立⑥",
"WorkItems": [],
"WorkPoints": [
"回転ﾄﾙｸ 10cN･m以下 ﾊﾞﾗﾂｷ 3cN･m以下",
"ﾓｰﾀ取付側でﾎﾞｰﾙﾈｼﾞに倣わせて組付け",
"摺動が悪い場合は軸受側に寄せてﾎﾞﾙﾄを締めなおす"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:<Y軸> ﾎﾞｰﾙﾈｼﾞ回転ﾄﾙｸ (ﾓｰﾀｰ組込み前)",
"WWYJ-5300-087"
]
} | {
"QualityItem": "回転ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "ﾊﾞﾗﾂｷ3cN・m以下",
"Method": "ﾄﾙｸｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立⑦",
"WorkItems": [
"1. ①にSENSOR をBOLT WASHER WASHER で組付け",
"2. 1.完成品にBRACKET をBOLT WASHER で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立⑧",
"WorkItems": [
"▲1. ①にSPACER SPACER をSCREW でADHESIVE ﾛｯｸﾀｲﾄを塗布して組付け",
"2. 1.完成品にCABLE-SUPPORT を挿入"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"接着剤塗布 ｺﾞﾏ粒:2"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立⑨",
"WorkItems": [
"1. BRACKET にSTOPPER ･SPACER をBOLT で組付け",
"2. ①に1.完成品をBOLT ･WASHER で組付け"
],
"WorkPoints": [
"対象品を組立"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"断面図"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸組立⑩",
"WorkItems": [
"1. ①にCOVER をBOLT で組付け",
"2. 1.完成品にPLATE をBOLT ･WASHER で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞX軸組立①",
"WorkItems": [
"■1. MOTOR の型式を確認しｼﾘｱﾙ番号を検査書に記載",
"2. LINEAR-WAY の型式を確認しｼﾘｱﾙ番号を検査書に記載",
"2. LINEAR-WAY にCOUPLING を挿入しMOTOR をBOLT ･WASHER で組付け",
"3. LINEAR-WAY のｶﾊﾞｰを取り外す"
],
"WorkPoints": [
"ｶｯﾌﾟﾘﾝｸﾞ部･ﾎﾞｰﾙﾈｼﾞ部共に取り外し:SD-A044756-020にて再取付",
"配線方向注意"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-087",
"InspectionItems": [
"検査表MOTOR :安全部品確認"
],
"WorkTypes": [],
"Words": [
"拡大図",
"･型式確認 ･ｼﾘｱﾙNo記録",
"･型式確認 ･ｼﾘｱﾙNo記録",
"検査表MOTOR :重要部品確認",
"COUPLING は仮止め:SD-A044756-022にて本締め",
"WWYJ-5300-087"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞX軸組立①",
"WorkItems": [
"■1. MOTOR の型式を確認しｼﾘｱﾙ番号を検査書に記載",
"2. LINEAR-WAY の型式を確認しｼﾘｱﾙ番号を検査書に記載",
"2. LINEAR-WAY にCOUPLING を挿入しMOTOR をBOLT ･WASHER で組付け",
"3. LINEAR-WAY のｶﾊﾞｰを取り外す"
],
"WorkPoints": [
"ｶｯﾌﾟﾘﾝｸﾞ部･ﾎﾞｰﾙﾈｼﾞ部共に取り外し:SD-A044756-020にて再取付",
"配線方向注意"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-087",
"InspectionItems": [
"検査表MOTOR :重要部品確認"
],
"WorkTypes": [],
"Words": [
"拡大図",
"･型式確認 ･ｼﾘｱﾙNo記録",
"検査表MOTOR :安全部品確認",
"･型式確認 ･ｼﾘｱﾙNo記録",
"COUPLING は仮止め:SD-A044756-022にて本締め",
"WWYJ-5300-087"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞX軸組立②",
"WorkItems": [
"1. ①にDOG をBOLT WASHER で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"裏面拡大図"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "Y軸ﾄﾞｯｷﾝｸﾞ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-087",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-087"
]
} | {
"QualityItem": "直角度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.02㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "直角ｽｺﾔ",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾄﾞｯｷﾝｸﾞ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-087"
]
} | {
"QualityItem": "直角度確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.02㎜以下",
"Method": "直角ｽｺﾔ",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸駆動部組立①",
"WorkItems": [
"1. PLATE にBLOCK をBOLT ･WASHER で組付け",
"2. 1.完成品にBOLT をNUT で仮止め",
"■3. MOTOR の型式を確認し､ｼﾘｱﾙNo.を検査書に記載",
"4. 2.完成品にMOTOR をBOLT ･WASHER で組付け"
],
"WorkPoints": [
"配線の向き注意"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-087",
"InspectionItems": [
"検査表PLATE :安全部品確認"
],
"WorkTypes": [],
"Words": [
"1.完成品",
"･型式確認 ･ｼﾘｱﾙNo記録",
"仮止め:SD-A044756-019にて本締め",
"2.完成品",
"WWYJ-5300-087"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸駆動部組立①",
"WorkItems": [
"1. PLATE にBLOCK をBOLT ･WASHER で組付け",
"2. 1.完成品にBOLT をNUT で仮止め",
"■3. MOTOR の型式を確認し､ｼﾘｱﾙNo.を検査書に記載",
"4. 2.完成品にMOTOR をBOLT ･WASHER で組付け"
],
"WorkPoints": [
"配線の向き注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"･型式確認 ･ｼﾘｱﾙNo記録",
"検査表PLATE :安全部品確認",
"仮止め:SD-A044756-019にて本締め",
"2.完成品",
"WWYJ-5300-087"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸駆動部組立②",
"WorkItems": [
"1. ①に②をBOLT WASHER で仮止め",
"2. 1.完成品にPULLEY PULLEY T-BELT をBOLT で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"仮止め:SD-A044756-019にて本締め",
"A矢視図",
"拡大図",
"仮止め:SD-A044756-019にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "原点出し治具",
"Size": "",
"ToolOther": "FM-3466",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸駆動部組立③",
"WorkItems": [
"1. ①の原点調整",
"2. 1.完成品のﾍﾞﾙﾄﾃﾝｼｮﾝ調整"
],
"WorkPoints": [
"ﾎﾞｰﾙﾈｼﾞ側のﾌﾟｰﾘｰは当付ける",
"ﾍﾞﾙﾄが平行かつ原点時にﾌﾟｰﾘｰ締付ﾎﾞﾙﾄが上を向いた状態にすること",
"プレートが㉗原点出しﾋﾟﾝに接触していること",
"㉖原点出し治具にてモーターの原点を調整(表示を00に調整)",
"仮止めしていたﾎﾞﾙﾄ､ﾅｯﾄを確実に増し締めすること"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-087",
"InspectionItems": [
"検査表①:<Y軸> ﾍﾞﾙﾄﾃﾝｼｮﾝ調整"
],
"WorkTypes": [],
"Words": [
"押当て",
"ここで測定",
"ﾍﾞﾙﾄ張力 200~220Hz (44±4N)",
"拡大図",
"原点確認",
"検査表①:<Y軸> ﾓｰﾀｰ原点調整",
"WWYJ-5300-087"
]
} | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3466",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸駆動部組立③",
"WorkItems": [
"1. ①の原点調整",
"2. 1.完成品のﾍﾞﾙﾄﾃﾝｼｮﾝ調整"
],
"WorkPoints": [
"ﾍﾞﾙﾄが平行かつ原点時にﾌﾟｰﾘｰ締付ﾎﾞﾙﾄが上を向いた状態にすること"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-087",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ここで測定",
"WWYJ-5300-087"
]
} | {
"QualityItem": "ﾍﾞﾙﾄﾃﾝｼｮﾝ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "ﾍﾞﾙﾄ張力200~220Hz(44±4N)",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "X軸原点調整",
"WorkItems": [
"1. ①の原点位置を調整しｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを増し締め",
"2. 1.完成品の取り外していたｶｯﾌﾟﾘﾝｸﾞ部ｶﾊﾞｰ･ﾎﾞｰﾙﾈｼﾞ部ｶﾊﾞｰを取付"
],
"WorkPoints": [
"㉖原点出し治具にてモーターの原点を調整(表示を00に調整)",
"ｽｹｰﾙ目で原点位置に移動させて､ ﾓｰﾀｰZ相位置にてｶｯﾌﾟﾘﾝｸﾞを固定｡"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-087",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:<X軸> ﾓｰﾀｰ原点調整",
"WWYJ-5300-087"
]
} | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "原点出し治具",
"RecordMethod": "WWYJ-5300-087",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "X軸原点調整",
"WorkItems": [
"1. ①の原点位置を調整しｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを増し締め",
"2. 1.完成品の取り外していたｶｯﾌﾟﾘﾝｸﾞ部ｶﾊﾞｰ･ﾎﾞｰﾙﾈｼﾞ部ｶﾊﾞｰを取付"
],
"WorkPoints": [
"㉖原点出し治具にてモーターの原点を調整(表示を00に調整)",
"ｽｹｰﾙ目で原点位置に移動させて､ ﾓｰﾀｰZ相位置にてｶｯﾌﾟﾘﾝｸﾞを固定｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:<X軸> ﾓｰﾀｰ原点調整"
]
} | {
"QualityItem": "原点確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "821㎜±0.5㎜原点確認",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "配線用ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. BRACKET にSHEET を貼付け",
"▲2. 1.完成品にSPACER ･SPACER をBOLT ･WASHER でﾛｯｸﾀｲﾄを塗布して組付け",
"3. 2.完成品にCABLE-SUPPORT を挿入"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"2.完成品",
"▲特殊作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "4.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線用ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. BRACKET にSHEET を貼付け",
"▲2. 1.完成品にSPACER ･SPACER をBOLT ･WASHER でﾛｯｸﾀｲﾄを塗布して組付け",
"3. 2.完成品にCABLE-SUPPORT を挿入"
],
"WorkPoints": [
"端面合わせ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"2.完成品",
"拡大図",
"4㎜",
"接着剤塗布 ｺﾞﾏ粒:2"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線用ﾌﾞﾗｹｯﾄ・ｶﾊﾞｰ取付",
"WorkItems": [
"▲1. ①にSPACER をSCREW でADHESIVE ﾛｯｸﾀｲﾄを塗布して組付け",
"▲2. 1.完成品に③をBOLT WASHER でADHESIVE ﾛｯｸﾀｲﾄを塗布して組付け",
"3. 2.完成品にCOVER をSCREW で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"2.完成品",
"拡大図",
"接着剤塗布 ｺﾞﾏ粒:2",
"接着剤塗布 ｺﾞﾏ粒:2"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "空圧部ﾄﾞｯｷﾝｸﾞ",
"WorkItems": [
"1. ①に②をBOLT WASHER で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"A矢視図"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞ部ﾄﾞｯｷﾝｸﾞ",
"WorkItems": [
"1. ①に⑥をBOLT WASHER で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"A断面図"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱｰ供給治具",
"Size": "",
"ToolOther": "FM-2823",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞ高さ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2823",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｲﾄｹﾞｰｼﾞ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞ高さ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-089",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-089"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "①384.5㎜±0.1㎜",
"Method": "ﾊｲﾄｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｲﾄｹﾞｰｼﾞ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞ高さ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-089"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "②417.5㎜±0.1㎜",
"Method": "ﾊｲﾄｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｲﾄｹﾞｰｼﾞ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞ高さ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-089"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "③412.0㎜±0.1㎜",
"Method": "ﾊｲﾄｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線配管引き回し①",
"WorkItems": [
"1. ①にLABEL TERMINAL PROCESS ･LABEL TERMINAL PROCESS のﾀｸﾞをを取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ITVEM4111P",
"E0501R",
"ITVMM4111P",
"ITYEM4110P",
"ITXEM4109P",
"ITYMM4110P",
"ITXMM4109P"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線配管引き回し②",
"WorkItems": [
"1. ①にCABLE CABLE CABLE の配線を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-115",
"InspectionItems": [
"検査表①:接続確認 (3)ICﾄﾚｲｽﾃｰｼﾞ部(正流れｽﾃｰｼﾞ)"
],
"WorkTypes": [],
"Words": [
"ITVME4111R",
"拡大図",
"E0501P",
"ITVMM4111R",
"ITVME4111P",
"E0501R",
"ITVMM4111P",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(300mm)",
"接続確認",
"WWYJ-5300-115"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-115",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線配管引き回し③",
"WorkItems": [
"1. ①にCABLE ･CABLE の配線を取付"
],
"WorkPoints": [
"ﾍﾞﾙﾄの下を通す"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-115",
"InspectionItems": [
"検査表①:接続確認 (4)ICﾄﾚｲｽﾃｰｼﾞ部(正流れｽﾃｰｼﾞD1500)"
],
"WorkTypes": [],
"Words": [
"1B11010R",
"A断面図",
"1B11020R",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"B11015R",
"B矢視図(ﾄﾚｲｽﾃｰｼﾞ下(Y軸部))",
"接続確認",
"検査表①:接続確認 (2)ICﾄﾚｲｽﾃｰｼﾞ部(ITY軸)",
"接続確認",
"WWYJ-5300-115"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-115",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線配管引き回し④",
"WorkItems": [
"1. ①にTUBE の配管を㉖で長さを調整し接続"
],
"WorkPoints": [
"L側配管を接続後､R側配管を接続し支柱にｲﾝｼｭﾛｯｸで固定",
"支柱の内側へ",
"支柱の内側へ",
"⑥の反対の端にﾏｽｷﾝｸﾞﾃｰﾌﾟで配管接続番号が判る様に明記の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"A矢視図",
"L1",
"L2",
"R2",
"R1",
"B矢視図",
"L1",
"L2",
"R2",
"R1",
"下段Down",
"下段Up",
"上段Down",
"上段Up",
"下段Down",
"下段Up",
"上段Down",
"上段Up",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(150mm)",
"C断面図",
"D断面図"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "配線配管引き回し⑤",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線配管引き回し⑥",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-115",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-115"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-115",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線配管引き回し⑦",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "配線配管引き回し⑧",
"WorkItems": [
"1. ①にTUBE ･TUBE の配管をｶｯﾄして接続"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"φ4黒 130mm",
"φ6橙 70mm",
"φ6橙 110mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "配線配管引き回し⑨",
"WorkItems": [
"1. ①にXｽﾃｰｼﾞからの配管をｶｯﾄして接続"
],
"WorkPoints": [
"φ4黒配管接続図",
"φ4黒 6芯ﾁｭｰﾌﾞ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(200mm)",
"A矢視図(ﾄﾚｲ吸着)",
"B矢視図(ﾄﾚｲｽﾃｰｼﾞ上下)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線配管引き回し⑩",
"WorkItems": [
"1. ①にCABLE CABLE CABLE の配線を接続"
],
"WorkPoints": [
"接続確認"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-115",
"InspectionItems": [
"検査表①:接続確認 (1)ICﾄﾚｲｽﾃｰｼﾞ部(ITX軸ｾﾝｻｰ､ﾊﾞﾙﾌﾞ)"
],
"WorkTypes": [],
"Words": [
"整線時はX軸ﾄﾞｸﾞとの干渉に注意",
"ｲﾝｼｭﾛｯｸ(100mm)",
"B10944R",
"R31034R",
"R31035R",
"R31036R",
"R31037R",
"G2A020",
"G2A021",
"R31044R",
"R31045R",
"R31046R",
"R31047R",
"R31031R",
"R31032R",
"R31033R",
"R31041R",
"R31042R",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WWYJ-5300-115"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-115",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3m",
"ToolOther": "",
"WorkName": "配線配管引き回し⑪",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "引き渡し準備",
"WorkItems": [
"1. ①COVER COVER SCREW CLAMPER SPACER BOLT WASHER BOLT BOLT WASHER WASHER を本体載せ込み工程に引き渡す"
],
"WorkPoints": [
"ｶﾊﾞｰの取付は本体載せ込み完了後に実施の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "引き渡し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き渡し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞ組立①",
"WorkItems": [
"2. PLATE ･PLATE にPAD を取付け",
"1. PLATE ･PLATE のｴｱｰ経路が指示通り通っていることを確認する",
"3. 2.完成品にBRACKET ･BRACKET をSCREW で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業ではそれぞれ2個作成",
"この作業ではそれぞれ2個作成",
"組付け詳細"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞ組立②",
"WorkItems": [
"1. ①･②にBRACKET をBOLT ･WASHER で組付け",
"2. 1.完成品にJOINT を組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業ではそれぞれ2個作成",
"この作業ではそれぞれ2個作成"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾄﾚｲｽﾃｰｼﾞ組立③",
"WorkItems": [
"1. TUBE を指定の長さでｶｯﾄ",
"2. ①･②に1.完成品を組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業ではそれぞれ2個作成",
"TUBE φ4白 100㎜ 4本"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:100㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ICﾄﾚｲｽﾃｰｼﾞ部へ引き渡し",
"WorkItems": [
"1. ①･②･BOLT ･WASHER を引き渡す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ1",
"WorkItems": [
"1. BLOCK FRAME FRAME をNUT NUT BOLT BOLT WASHER で取付"
],
"WorkPoints": [
"寸法通り取付けるBLOCK FRAME FRAME の合わせ面に隙間が無い事",
"2ｾｯﾄ製作",
"FRAME FRAME は端面合わせの事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"271㎜",
"119㎜",
"119㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ2",
"WorkItems": [
"1. ①にPLATE をPLATE で挟んでBOLT WASHER で取付",
"1. ①にPLATE をPLATE で挟んでBOLT WASHER で取付"
],
"WorkPoints": [
"左ﾊﾝﾄﾞ組立",
"右ﾊﾝﾄﾞ組立"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "1/100",
"WorkName": "ﾌﾚｰﾑ3",
"WorkItems": [
"1. ①を定盤上でN015ﾌﾚｰﾑ上面の高さを測定する"
],
"WorkPoints": [
"2ﾋﾟｰｽ測定",
"0.4㎜以内",
"P002の下面と定盤に隙間が無い事"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-46",
"InspectionItems": [
"検査表①:P(2軸)3 ｱﾙﾑﾌﾚｰﾑ高さ測定"
],
"WorkTypes": [],
"Words": [
"A001",
"P005､P006",
"P004",
"N015",
"P003",
"定盤",
"1~4相互の高低差を確認",
"WWYJ-5300-46"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "高低差0.4㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-46",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "左ﾌﾚｰﾑ",
"WorkItems": [
"1. FRAME にBRACKET をNUT BOLT WASHER で取付",
"2. 1.完成品にJOINT をBOLT WASHER WASHER で取付",
"3. 2.完成品にCABLE-SUPPORT を取付",
"4. 3.完成品にNUT を入れる",
"1. FRAME にBRACKET をNUT BOLT WASHER で取付",
"2. 1.完成品にJOINT をBOLT WASHER WASHER で取付",
"3. 2.完成品にCABLE-SUPPORT を取付",
"4. 3.完成品にNUT を入れる"
],
"WorkPoints": [
"FRAME は方向あり",
"FRAME の裏面に8個入れる",
"FRAME の表面に2個入れる位置は不問",
"FRAME は方向あり",
"FRAME の裏面に8個入れる",
"FRAME の表面に2個入れる位置は不問"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"230㎜",
"166.3㎜",
"45㎜",
"15㎜",
"28㎜",
"120㎜",
"230㎜",
"166.3㎜",
"45㎜",
"15㎜",
"28㎜",
"120㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "右ﾌﾚｰﾑ",
"WorkItems": [
"1. FRAME にBRACKET をNUT BOLT WASHER で取付",
"2. 1.完成品にJOINT をBOLT WASHER WASHER で取付",
"3. 2.完成品にCABLE-SUPPORT を取付",
"4. 3.完成品にNUT を入れる",
"1. FRAME にBRACKET をNUT BOLT WASHER で取付",
"2. 1.完成品にJOINT をBOLT WASHER WASHER で取付",
"3. 2.完成品にCABLE-SUPPORT を取付",
"4. 3.完成品にNUT を入れる"
],
"WorkPoints": [
"FRAME は方向あり",
"FRAME の裏面に8個入れる",
"FRAME の表面に2個入れる位置は不問",
"FRAME は方向あり",
"FRAME の裏面に8個入れる",
"FRAME の表面に2個入れる位置は不問"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付け1",
"WorkItems": [
"1. ①にLABEL を貼付け"
],
"WorkPoints": [
"2ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾒﾓﾘとの合わせ基準",
"ﾒﾓﾘとの合わせ基準"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付け2",
"WorkItems": [
"1. ①にLABEL を貼付け"
],
"WorkPoints": [
"この範囲の貼付け寸法を明示右側も同じ",
"2ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"2㎜",
"5㎜",
"80㎜",
"5㎜",
"5㎜",
"230㎜",
"5㎜",
"5㎜",
"5㎜",
"2㎜",
"80㎜",
"230㎜"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "銘板貼付け3",
"WorkItems": [
"1. BRACKET にLABEL を貼付け",
"3. BRACKET にLABEL を貼付け",
"4. 3.完成品にCABLE-SUPPORT を取付ける",
"2. 1.完成品にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"左ﾊﾝﾄﾞ用",
"右ﾊﾝﾄﾞ用"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"23㎜",
"155㎜",
"155㎜",
"23㎜"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "銘板貼付け4",
"WorkItems": [
"1. COVER にLABEL を貼付け",
"3. COVER にLABEL を貼付け",
"4. 3.完成品にCABLE-SUPPORT を取付ける",
"2. 1.完成品にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"注) AMPP構成時",
"注) AMP構成時はこちらを貼る",
"左ﾊﾝﾄﾞ用",
"右ﾊﾝﾄﾞ用"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"32㎜",
"2㎜",
"32㎜",
"2㎜"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾝﾄﾞﾊﾞﾙﾌﾞ1",
"WorkItems": [
"1. JOINT SPACER JOINT を取付"
],
"WorkPoints": [
"16ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾝﾄﾞﾊﾞﾙﾌﾞ2",
"WorkItems": [
"1. ①にJOINT を取付(4か所)",
"2. 1.完成品にVALVE をBOLT WASHER WASHER で取付(12か所)",
"1. 2｡完成品のJOINT VALVE に④を取付(16か所)"
],
"WorkPoints": [
"VALVE は方向あり",
"左ﾊﾝﾄﾞ用",
"右ﾊﾝﾄﾞ用",
"矢印方向に取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"10㎜",
"10㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:10.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "治具",
"Size": "",
"ToolOther": "FM-6046",
"WorkName": "搬送PAD組立①",
"WorkItems": [
"1. BLOCK にVACUUM-PAD を仮取付(ﾅｯﾄはVACUUM-PAD の付属品を使用)",
"3. PAD高さ調整を行う｡",
"2. 1.完成品を㉗搬送PAD高さ合わせジグに取付"
],
"WorkPoints": [
"32ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-46",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-46"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-6046",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "29.8±0.1㎜(隙間0.1㎜以内)",
"Method": "治具",
"RecordMethod": "WWYJ-5300-46",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "搬送PAD組立①",
"WorkItems": [
"1. BLOCK にVACUUM-PAD を仮取付(ﾅｯﾄはVACUUM-PAD の付属品を使用)",
"3. PAD高さ調整を行う｡",
"2. 1.完成品を㉗搬送PAD高さ合わせジグに取付"
],
"WorkPoints": [
"32ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-46"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "29.8±0.1㎜(隙間0.1㎜以内)",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-46",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送PAD組立②",
"WorkItems": [
"▲1. ①に①の付属品をADHESIVE ﾈｼﾞﾛｯｸ材で取付",
"▲2. 1.完成品上部の①付属品のﾌﾟﾗｸﾞを取り外し､JOINT をADHESIVE ﾈｼﾞﾛｯｸ材で取付 ｼﾞｮｲﾝﾄの向き注意"
],
"WorkPoints": [
"吸着穴に接着剤が混入し無い事",
"吸着穴に接着剤が混入し無い事",
"4ｾｯﾄ製作",
"8ｾｯﾄ製作",
"4ｾｯﾄ製作",
"下部ｼﾞｮｲﾝﾄと上部ｼﾞｮｲﾝﾄの向き違いがある",
"3種類製作する",
"Φ30仕様(標準)時は､JOINT を選択",
"Φ15仕様(個別)時は､JOINT を選択"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-46",
"InspectionItems": [
"検査表①:P(2軸)､ねじﾛｯｸ塗布",
"検査表①:P(2軸)､ねじﾛｯｸ塗布"
],
"WorkTypes": [],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:2",
"接着剤塗布 ｺﾞﾏ粒:2",
"ADHESIVE ねじﾛｯｸ塗布",
"①の付属品(ADHESIVE ねじﾛｯｸ塗布)",
"WWYJ-5300-46"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "WWYJ-5300-46",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送PAD組立③",
"WorkItems": [
"▲1. ①に①の付属品をﾈｼﾞﾛｯｸ材で取付"
],
"WorkPoints": [
"吸着穴に接着剤が混入し無い事",
"16ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-46",
"InspectionItems": [
"検査表①:AM2､ねじﾛｯｸ塗布"
],
"WorkTypes": [],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:2",
"①の付属品(ねじﾛｯｸ塗布)",
"①の付属品(ねじﾛｯｸ塗布)",
"WWYJ-5300-46"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "WWYJ-5300-46",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "左吸着ﾊﾝﾄﾞ組立1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:210.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左吸着ﾊﾝﾄﾞ組立2",
"WorkItems": [
"1. ②を①にNUT BOLT WASHER で取付"
],
"WorkPoints": [
"端面合わせ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "左吸着ﾊﾝﾄﾞ組立3",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5㎜",
"110㎜",
"110㎜",
"40㎜",
"40㎜",
"40㎜",
"40㎜",
"110㎜",
"5㎜",
"110㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左吸着ﾊﾝﾄﾞ組立4",
"WorkItems": [
"1. ①にTUBE TUBE TUBE TUBE TUBE を取付",
"2. 各配管を㉘で固定"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左吸着ﾊﾝﾄﾞ組立5",
"WorkItems": [
"▲1. CAP CAP にADHESIVE を塗布し①に取付"
],
"WorkPoints": [
"CAP の中央部2本の爪は㉘で切断する"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-46",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:(P2軸)2,接着剤塗布",
"接着剤塗布 小豆:2",
"WWYJ-5300-46"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:2",
"Method": "目視",
"RecordMethod": "WWYJ-5300-46",
"Other": "ﾛｯｸﾀｲﾄ415",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "右吸着ﾊﾝﾄﾞ組立1",
"WorkItems": [
"1. ①に②をNUT BOLT WASHER で仮付け",
"2. BRACKET BRACKET をNUT WASHER BOLT WASHER で仮付け",
"3. 取付位置を210㎜に合わせ､各部品を隙間なく取付ける(本締め)"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:210.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右吸着ﾊﾝﾄﾞ組立2",
"WorkItems": [
"1. ②を①にNUT BOLT WASHER で取付"
],
"WorkPoints": [
"端面合わせ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "右吸着ﾊﾝﾄﾞ組立3",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5㎜",
"110㎜",
"110㎜",
"40㎜",
"40㎜",
"40㎜",
"40㎜",
"110㎜",
"5㎜",
"110㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "右吸着ﾊﾝﾄﾞ組立4",
"WorkItems": [
"1. ①にTUBE TUBE TUBE TUBE TUBE を取付",
"2. 各配管を㉘で固定"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右吸着ﾊﾝﾄﾞ組立5",
"WorkItems": [
"▲1. CAP CAP にADHESIVE を塗布し①に取付"
],
"WorkPoints": [
"CAP の中央部2本の爪は㉘で切断する"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-46",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:(P2軸)2､接着剤塗布",
"接着剤塗布 小豆:2",
"WWYJ-5300-46"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:2",
"Method": "目視",
"RecordMethod": "WWYJ-5300-46",
"Other": "ﾛｯｸﾀｲﾄ415",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "次工程へ引き渡し",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. ①②③BOLT BOLT WASHER WASHER BOLT WASHER を次工程へ｡"
]
} | {
"QualityItem": "引き渡し部材確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "正しい部材が引き渡される事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝﾀﾘﾝｸﾞﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ⑥の取付用ﾎﾞﾙﾄ､ﾜｯｼｬを使ってBLOCK を取付"
],
"WorkPoints": [
"PINに当付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒﾝﾃﾅﾝｽﾗｲﾄP組立",
"WorkItems": [
"1. BRACKET にLED-LAMP-UNIT をBOLT WASHER WASHER で取付ける",
"2. 1の完成品にLABEL TERMINAL PROCESS を取付ける",
"3. 2の完成品とNUT SUPPORT BOLT WASHER を付属する"
],
"WorkPoints": [
"合わせる",
"ﾗﾍﾞﾙ2種類"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"E0131R",
"E0131R",
"E0231R",
"SFN-SA4 4個",
"SFA-9A2 4個",
"六角穴付きﾎﾞﾙﾄM4×10 4本平座金 みがき丸 4 4個",
"この作業ではﾗﾍﾞﾙ違いを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6481",
"WorkName": "ﾏｸﾞﾈｯﾄ取付け",
"WorkItems": [
"1. ﾊｰﾈｽﾎﾞｰﾄﾞにﾏｸﾞﾈｯﾄを取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"⇒ﾏｸﾞﾈｯﾄ中",
"⇒ﾏｸﾞﾈｯﾄ大"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6481",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊｰﾈｽ準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.下記ﾘｽﾄの順番でｹｰﾌﾞﾙを準備する"
]
} | {
"QualityItem": "ｹｰﾌﾞﾙの準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6481",
"WorkName": "ﾊｰﾈｽ引き回1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN8K011",
"R31140RR31141R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6481",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6481",
"WorkName": "ﾊｰﾈｽ引き回2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1G10340-1R",
"G10340P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6481",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6481",
"WorkName": "ﾊｰﾈｽ引き回3",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1G10340-2R",
"G10341P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6481",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6481",
"WorkName": "ﾊｰﾈｽ引き回4",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1G10340-3R",
"G10342P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6481",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6481",
"WorkName": "ﾊｰﾈｽ引き回5",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1G10340-4R",
"G10343P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6481",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6481",
"WorkName": "ﾊｰﾈｽ引き回6",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1G10340-5R",
"G10344P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6481",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6481",
"WorkName": "ﾊｰﾈｽ引き回7",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1G10340-6R",
"G10345P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6481",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6481",
"WorkName": "ﾊｰﾈｽ引き回8",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ADPW-05ADPW-15",
"CN1K6001",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6481",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6481",
"WorkName": "ﾊｰﾈｽ引き回9",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN10K003",
"BX2112",
"1G10330R",
"1G10340R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6481",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6481",
"WorkName": "ﾊｰﾈｽ引き回10",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"C-X2112",
"PLED1P",
"1. CABLE を引き回す",
"1X012"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6481",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6481",
"WorkName": "ｲﾝｼｭﾛｯｸ固定",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. ｲﾝｼｭﾛｯｸで固定する",
"⇒100mm",
"⇒150mm",
"⇒200mm",
"⇒250mm"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6481",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑ組立①",
"WorkItems": [
"1. FRAME-KIT(L) にFRAME-KIT(REAR) をBOLT WASHER で取付"
],
"WorkPoints": [
"取付は仮固定※4面体にするまで､ﾎﾞﾙﾄの本締めはしない",
"【注意】 WASHER 歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×3"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑ組立②",
"WorkItems": [
"1. ①にFRAME-KIT(R) をBOLT ･WASHER で取付"
],
"WorkPoints": [
"取付は仮固定※4面体にするまで､ﾎﾞﾙﾄの本締めはしない",
"【注意】 WASHER 歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側"
],
"Tolks": [
"締付ﾄﾙｸ 11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×2"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾌﾚｰﾑ組立③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑ組立③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3.5m",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑ組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑ組立⑤",
"WorkItems": [
"1. ①に⑥をBOLT WASHER BOLT BRACKET で取付"
],
"WorkPoints": [
"下面にBOLT ･⑩で取付(①と⑥WASHER BRACKET の隙間無い事)",
"【注意】 ③歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側",
"【注意】 下記取付け寸法は標準HEPA仕様の場合です",
"前側のﾌﾚｰﾑと左右ﾌﾚｰﾑ､及び⑥は､各面の段差が無いように調整し､ﾎﾞﾙﾄを締結する"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×20",
"×4",
"×16"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3.5m",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立⑥",
"WorkItems": [
"1. ①にFRAME-KIT(UPPER4) をBOLT WASHER で取付"
],
"WorkPoints": [
"下面図",
"【注意】 WASHER 歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側",
"①とFRAME-KIT(UPPER4) は､各面の段差が無いように調整し､ﾎﾞﾙﾄを締結する",
"上面拡大図"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×4",
"×4"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "1725±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑ組立⑥",
"WorkItems": [
"1. ①にFRAME-KIT(UPPER4) をBOLT WASHER で取付"
],
"WorkPoints": [
"下面図",
"【注意】 WASHER 歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側",
"①とFRAME-KIT(UPPER4) は､各面の段差が無いように調整し､ﾎﾞﾙﾄを締結する",
"上面拡大図"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×4",
"×4"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立⑦",
"WorkItems": [
"1. FRAME-KIT(FRONT) (L) ・FRAME-KIT(FRONT) (R) にBRACKET ・BRACKET をWASHER ・BOLT ・WASHER ・㉓で取付",
"2. ①に1.完成品-1・-2をWASHER ・BOLT ・⑧・㉓で取付"
],
"WorkPoints": [
"端面を合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:320㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑ組立⑦",
"WorkItems": [
"1. FRAME-KIT(FRONT) (L) ・FRAME-KIT(FRONT) (R) にBRACKET ・BRACKET をWASHER ・BOLT ・WASHER ・㉓で取付",
"2. ①に1.完成品-1・-2をWASHER ・BOLT ・⑧・㉓で取付",
"1. FRAME-KIT(FRONT) (L) ・FRAME-KIT(FRONT) (R) にBRACKET ・BRACKET をWASHER ・BOLT ・WASHER ・㉓で取付",
"2. ①に1.完成品-1・-2をWASHER ・BOLT ・⑧・㉓で取付"
],
"WorkPoints": [
"端面を合わせる",
"端面を合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑ組立⑧",
"WorkItems": [
"1. ①にFRAME-KIT(FRONT) (C) をBOLT ･WASHER で取付",
"2. 裏側より､WASHER ･BOLT で取付"
],
"WorkPoints": [
"【注意】 WASHER 歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側",
"取付は仮固定※ﾎﾞﾙﾄの本締めはしない",
"取付は仮固定※ﾎﾞﾙﾄの本締めはしない"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×6"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3.5m",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立⑨",
"WorkItems": [
"1. ①にFRAME-KIT(FRONT) をBOLT WASHER で取付",
"2. ﾌﾚｰﾑ【FL､FR､C､F】連結ﾎﾞﾙﾄを本締めする"
],
"WorkPoints": [
"取付は仮固定※ﾎﾞﾙﾄの本締めはしない",
"各ﾌﾚｰﾑの段差が無いように調整し締結する",
"【注意】 WASHER 歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"170mm",
"ﾌﾚｰﾑ【F】",
"ﾌﾚｰﾑ【F】",
"ﾌﾚｰﾑ【C】",
"ﾌﾚｰﾑ【FL】",
"ﾌﾚｰﾑ【FR】",
"765mm",
"1518mm",
"1518mm",
"170mm",
"765mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑ組立⑨",
"WorkItems": [],
"WorkPoints": [
"【注意】 WASHER 歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1518mm",
"170mm",
"765mm"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FRONT_戸当たりｺﾞﾑ取付",
"WorkItems": [
"1. ①前面に指定寸法にてRUBBER-LEG SPACER をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"5mm",
"×8"
]
} | {
"QualityItem": "外観確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｷｽﾞ無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.