suryagunukula's picture
Initial release
035592e
Raw History Blame Contribute Delete
3.89 kB
`timescale 1ns/1ns
`define clk_period 20
module tb_multi_pipe();
reg [7:0] mul_a;
reg [7:0] mul_b;
reg mul_en_in;
reg clk;
reg rst_n;
wire mul_en_out;
wire [15:0] mul_out;
reg [15:0] expected_product;
multi_pipe_8bit u1(
.clk(clk),
.rst_n(rst_n),
.mul_a(mul_a),
.mul_b(mul_b),
.mul_en_in(mul_en_in),
.mul_en_out(mul_en_out),
.mul_out(mul_out)
);
initial clk = 1;
always # 10 clk = ~clk;
integer error = 0;
// ---------------- Additional checks ----------------
integer herr = 0, hpush = 0, hpop = 0, hk;
reg hon = 0, hmon = 0;
reg [15:0] hq [0:255];
always @(posedge rst_n) hon = 1;
always @(negedge clk) if (hon && mul_en_out === 1'b0 && mul_out !== 16'd0) begin
herr = herr + 1;
if (herr < 10) $display("HCHK idle: mul_en_out=0 but mul_out=%0d at %0t", mul_out, $time);
end
always @(posedge clk) if (hmon && mul_en_in === 1'b1) begin hq[hpush] = mul_a * mul_b; hpush = hpush + 1; end
always @(negedge clk) if (hmon && mul_en_out === 1'b1) begin
if (hpop >= hpush || mul_out !== hq[hpop]) begin
herr = herr + 1;
$display("HCHK stream: result #%0d got %0d expected %0d", hpop, mul_out, hq[hpop]);
end
hpop = hpop + 1;
end
task h_stream;
begin
@(negedge clk);
mul_en_in = 0;
repeat (20) @(negedge clk);
hmon = 1;
for (hk = 0; hk < 160; hk = hk + 1) begin
mul_a = $random; mul_b = $random;
mul_en_in = (hk < 40) ? 1'b1 : $random;
@(negedge clk);
end
mul_en_in = 0;
repeat (20) @(negedge clk);
hmon = 0;
if (hpop != hpush) begin
herr = herr + 1;
$display("HCHK stream: %0d operand pairs accepted but %0d mul_en_out=1 cycles", hpush, hpop);
end
end
endtask
initial begin
rst_n = 0;
mul_a = 0;
mul_b = 0;
mul_en_in = 0;
#(`clk_period*200+1);
rst_n = 1;
#(`clk_period*10);
mul_a = 'd35;
mul_b = 'd20;
mul_en_in = 'd1;
repeat (100) begin
mul_en_in = 0;
#(`clk_period*20);
rst_n = 1;
#(`clk_period*10);
mul_a = $random;
mul_b = $random;
mul_en_in = 'd1;
#(`clk_period);
expected_product = mul_a * mul_b;
#(`clk_period);
error = ((mul_en_out==1) && (mul_out == expected_product)) ? error+1 : error;
while (mul_en_out == 0) begin
@(posedge clk); // Wait for one clock cycle
end
// //========it can be changed depending on your pipelining processing latency
// #(`clk_period*4);
// //========it can be changed depending on your pipelining processing latency
error = (mul_out != expected_product) ? error+1 : error;
// $display("mul_a = %d, mul_b = %d, mul_out = %d, expected = %d", mul_a, mul_b, mul_out, expected_product);
end
// Additional checks, after the original 100 checks:
// H1 "Otherwise, mul_out is set to 0": whenever mul_en_out is 0, mul_out is 0 (monitored at every falling
// clock edge from the first reset release to the end of the run, original stimulus included).
// H2 pipelining: 160 cycles of new random operands every cycle with a random mul_en_in pattern; every
// mul_en_out=1 cycle must show the product of the next accepted (mul_en_in=1) operand pair, in order.
h_stream;
error = error + herr;
if (error == 0) begin
$display("===========Your Design Passed===========");
end
else begin
$display("===========Test completed with %d /100 failures===========", error);
end
$finish;
end
endmodule