Download Control/Counter/counter_12/testbench.v from chipagents/RTLLM-verified: direct link, hf CLI and curl.
- Browser
- Download file 2.33 kB
-
https://huggingface.co/datasets/chipagents/RTLLM-verified/resolve/main/Control/Counter/counter_12/testbench.v
- Command line
-
hf download hf://datasets/chipagents/RTLLM-verified/Control/Counter/counter_12/testbench.v
-
curl -L -o testbench.v https://huggingface.co/datasets/chipagents/RTLLM-verified/resolve/main/Control/Counter/counter_12/testbench.v
2.33 kB
| module counter_12_tb; | |
| reg clk, rst_n, valid_count; | |
| wire [3:0] out; | |
| counter_12 dut ( | |
| .rst_n(rst_n), | |
| .clk(clk), | |
| .valid_count(valid_count), | |
| .out(out) | |
| ); | |
| always #5 clk = ~clk; | |
| integer i = 0; | |
| integer error = 0; | |
| integer hexp; | |
| task hard_chk(input [3:0] exp, input [8*28-1:0] what); | |
| begin | |
| if (out !== exp) begin | |
| error = error + 1; | |
| $display("HARD %0t: out=%0d, expected %0d (%0s)", $time, out, exp, what); | |
| end | |
| end | |
| endtask | |
| initial begin | |
| clk = 0; | |
| rst_n = 0; | |
| valid_count = 0; | |
| #20 rst_n = 1; | |
| // testcase1: validation of valid_count | |
| repeat(15) begin | |
| error = (out == 0) ?error:error+1; | |
| #10; | |
| end | |
| // testcase2: counter | |
| #100 valid_count = 1; | |
| repeat(11) begin | |
| error = (out == i) ?error:error+1; | |
| i = i+1; | |
| #10; | |
| end | |
| // testcase3: the count is paused if valid_count is invalid | |
| valid_count = 0; | |
| repeat(5) begin | |
| error = (out == 11) ?error:error+1; | |
| #10; | |
| end | |
| // additional check (t=430; clk rises at x5, out sampled at x0 as above): wrap 11 -> 0, pause mid-count, mid-run reset. | |
| valid_count = 1; | |
| hexp = 11; | |
| repeat (27) begin // 11 -> 0,1,..,11,0,..,11,0,1,2 | |
| #10; | |
| hexp = (hexp == 11) ? 0 : hexp + 1; | |
| hard_chk(hexp, "counting (wrap after 11)"); | |
| end | |
| valid_count = 0; | |
| repeat (3) begin #10; hard_chk(hexp, "paused"); end | |
| valid_count = 1; | |
| repeat (12) begin // through 11 -> 0 again | |
| #10; | |
| hexp = (hexp == 11) ? 0 : hexp + 1; | |
| hard_chk(hexp, "counting (wrap after 11)"); | |
| end | |
| #2 rst_n = 0; // x2, valid_count=1, held low across two rising edges | |
| #18 hard_chk(0, "rst_n low"); // x0, after two edges | |
| #7 rst_n = 1; // x7, released between edges | |
| #3 hard_chk(0, "after reset"); // x0, no rising edge since the release | |
| hexp = 0; | |
| repeat (13) begin | |
| #10; | |
| hexp = (hexp == 11) ? 0 : hexp + 1; | |
| hard_chk(hexp, "counting after reset"); | |
| end | |
| if (error == 0) begin | |
| $display("===========Your Design Passed==========="); | |
| end | |
| else begin | |
| $display("===========Failed===========", error); | |
| end | |
| $finish; | |
| end | |
| endmodule |