Upload constructcie.json

constructcie.json

@@ -129,7 +129,7 @@
 {"id": 131579.015, "accident_report": {"text": ["Employee #1, employed by a construction company, was assigned to clean hatch openings and covers on a derrick boat, so that the hatch openings could be closed and sealed after the Load Line Certification Inspection was completed. There were no witnesses to this incident, but according to subsequent investigation, Employee #1 was believed to have been removing silicon caulking and sweeping debris away from the port side hatch openings and covers, near the main deck edge and approximately one-third of the vessel length from the bow. Employee #1 was found by the superintendent. When found, he was unresponsive in 40 degree Fahrenheit water below the deck area and between the tires protecting the derrick boat's hull and the shore wall. He was not wearing a personal flotation device when found. the county medical examiner had not determined cause of death, although the preliminary examination suggested that Employee #1 had not drowned, no significant injuries were observed, and hypothermia had not been ruled out. Being immersed in 40 degree Fahrenheit water for an unknown time period is believed to have contributed to his death."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1, employed by a construction company, was assigned to clean hatch openings and covers on a derrick boat, so that the hatch openings could be closed and sealed after the Load Line Certification Inspection was completed. There were no witnesses to this incident, but according to subsequent investigation, Employee #1 was believed to have been removing silicon caulking and sweeping debris away from the port side hatch openings and covers, near the main deck edge and approximately one-third of the vessel length from the bow"], "keywords": [["employed by a construction company", "clean hatch openings and covers on a derrick boat", "Load Line Certification Inspection", "removing silicon caulking and sweeping debris", "port side hatch openings and covers"]], "children": {"construction_trade": {"type": "classification", "value": ["general requirements"]}}}, "object_involved": {"type": "extraction", "text": ["tires", "shore wall"], "keywords": [["tires"], ["shore wall"]]}, "behavioral_factors": {"type": "extraction", "text": ["He was not wearing a personal flotation device"], "keywords": [["not wearing a personal flotation device"]], "children": {"noncompliant_behavior": {"type": "extraction", "text": ["was not wearing a personal flotation device"], "keywords": [["not wearing a personal flotation device"]]}}}, "consequences": {"type": "extraction", "text": ["death"], "keywords": [["death"]], "children": {"severity": {"type": "classification", "value": ["fatality"]}}}}}, "accident_type": {"type": "classification", "value": ["caught-in/between"]}}
 {"id": 131600.015, "accident_report": {"text": ["Employee #1, employed by a roofing company, was on the roof of a three-story multifamily residential structure and retrieving a cell phone during a rehabilitation project. The roof was icy. Employee #1 lost traction on the icy surface and fell, a fall height of 28 feet. Employee #1 was killed."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1, employed by a roofing company, was on the roof of a three-story multifamily residential structure and retrieving a cell phone during a rehabilitation project"], "keywords": [["employed by a roofing company", "roof of a three-story multifamily residential structure", "retrieving a cell phone during a rehabilitation project"]], "children": {"construction_trade": {"type": "classification", "value": ["thermal and moisture protection"]}}}, "object_involved": {"type": "extraction", "text": ["roof"], "keywords": [["roof"]]}, "working_condition_factors": {"type": "extraction", "text": ["roof was icy"], "keywords": [["roof was icy"]], "children": {"workspace_condition": {"type": "extraction", "text": ["roof was icy"], "keywords": [["roof was icy"]]}}}, "consequences": {"type": "extraction", "text": ["Employee #1 was killed"], "keywords": [["killed"]], "children": {"severity": {"type": "classification", "value": ["fatality"]}}}}}, "accident_type": {"type": "classification", "value": ["fall"]}}
 {"id": 131583.015, "accident_report": {"text": ["Employee #1, employed by a construction company, was installing a platform and staircase for emergency access/egress at a commercial building. He was working from an extension ladder leaned against a 6-inch wide vertical steel column, with the two rails not supported equally and no single support attachment. Employee #1 was drilling holes under the surface of the horizontal steel platform when the drill became caught and hung up, which caused the drill to spin. The spinning drill struck the employee in the head and knocked him off the ladder. The employee fell, a fall height of 10 feet, and struck the concrete surface. The employee was transported to the hospital and admitted for treatment of blunt force traumatic head injuries. Employee #1 died at the hospital."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1, employed by a construction company, was installing a platform and staircase for emergency access/egress at a commercial building"], "keywords": [["employed by a construction company", "installing a platform and staircase for emergency access/egress", "commercial building"]], "children": {"construction_trade": {"type": "classification", "value": ["metals"]}}}, "object_involved": {"type": "extraction", "text": ["ladder"], "keywords": [["ladder"]]}, "working_condition_factors": {"type": "extraction", "text": ["extension ladder leaned against a 6-inch wide vertical steel column, with the two rails not supported equally and no single support attachment"], "keywords": [["extension ladder", "leaned against a 6-inch wide vertical steel column", "two rails not supported equally", "no single support attachment"]], "children": {"workspace_condition": {"type": "extraction", "text": ["extension ladder leaned against a 6-inch wide vertical steel column, with the two rails not supported equally and no single support attachment"], "keywords": [["extension ladder", "leaned against a 6-inch wide vertical steel column", "two rails not supported equally", "no single support attachment"]]}}}, "consequences": {"type": "extraction", "text": ["admitted for treatment of blunt force traumatic head injuries. Employee #1 died"], "keywords": [["blunt force traumatic head injuries", "died"]], "children": {"severity": {"type": "classification", "value": ["fatality"]}, "affected_body_part": {"type": "extraction", "text": ["head"], "keywords": [["head"]]}}}}}, "accident_type": {"type": "classification", "value": ["fall"]}}
-{"id": 131555.015, "accident_report": {"text": ["Employee #1 and three coworkers, employed by a company subcontracted to do painting for a new casino, were tasked with priming and painting the electronic gate at the loading dock. Each leaf of the gate measured approximately 24 feet by 9 feet and weighed approximately 3,000 pounds. However, the gate was not complete, and it was missing the safety controls, including the motor (Heavy Duty SL-175 DC Slide Gate Operator) and chain that would prevent it from being pulled past the wheel guide end point. The employer did not conduct an inspection of the loading dock gate prior to the gate being pulled out for painting and priming. In preparation for painting, the four employees pulled out the gate. When the gate overextended past the wheel guide end point, it began to wobble. The employees lost control of the gate, which fell, striking and crushing Employee #1."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1 and three coworkers, employed by a company subcontracted to do painting for a new casino, were tasked with priming and painting the electronic gate at the loading dock"], "keywords": [["subcontracted to do painting for a new casino", "priming and painting the electronic gate at the loading dock"]], "children": {"construction_trade": {"type": "classification", "value": ["finishes"]}}}, "object_involved": {"type": "extraction", "text": ["gate"], "keywords": [["gate"]]}, "managerial_factors": {"type": "extraction", "text": ["employer did not conduct an inspection of the loading dock gate prior to the gate being pulled out for painting and priming"], "keywords": [["employer did not conduct an inspection", "loading dock gate"]], "children": {"failure_of_hazard_management": {"type": "extraction", "text": ["employer did not conduct an inspection of the loading dock gate"], "keywords": [["employer did not conduct an inspection", "loading dock gate"]]}}}, "equipment_factors": {"type": "extraction", "text": ["gate was not complete, and it was missing the safety controls, including the motor (Heavy Duty SL-175 DC Slide Gate Operator) and chain that would prevent it from being pulled past the wheel guide end point"], "keywords": [["gate was not complete", "missing the safety controls"]], "children": {"work_equipment_condition": {"type": "extraction", "text": ["gate was not complete, and it was missing the safety controls"], "keywords": [["gate was not complete", "missing the safety controls"]]}}}, "consequences": {"type": "extraction", "children": {"severity": {"type": "classification", "value": ["fatality"]}}}}}, "accident_type": {"type": "classification", "value": ["struck-by"]}}
+{"id": 131555.015, "accident_report": {"text": ["Employee #1 and three coworkers, employed by a company subcontracted to do painting for a new casino, were tasked with priming and painting the electronic gate at the loading dock. Each leaf of the gate measured approximately 24 feet by 9 feet and weighed approximately 3,000 pounds. However, the gate was not complete, and it was missing the safety controls, including the motor (Heavy Duty SL-175 DC Slide Gate Operator) and chain that would prevent it from being pulled past the wheel guide end point. The employer did not conduct an inspection of the loading dock gate prior to the gate being pulled out for painting and priming. In preparation for painting, the four employees pulled out the gate. When the gate overextended past the wheel guide end point, it began to wobble. The employees lost control of the gate, which fell, striking and crushing Employee #1."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1 and three coworkers, employed by a company subcontracted to do painting for a new casino, were tasked with priming and painting the electronic gate at the loading dock"], "keywords": [["subcontracted to do painting for a new casino", "priming and painting the electronic gate at the loading dock"]], "children": {"construction_trade": {"type": "classification", "value": ["finishes"]}}}, "object_involved": {"type": "extraction", "text": ["gate"], "keywords": [["gate"]]}, "managerial_factors": {"type": "extraction", "text": ["employer did not conduct an inspection of the loading dock gate prior to the gate being pulled out for painting and priming"], "keywords": [["employer did not conduct an inspection", "loading dock gate"]], "children": {"failure_of_hazard_management": {"type": "extraction", "text": ["employer did not conduct an inspection of the loading dock gate"], "keywords": [["employer did not conduct an inspection", "loading dock gate"]]}}}, "equipment_factors": {"type": "extraction", "text": ["gate was not complete, and it was missing the safety controls, including the motor (Heavy Duty SL-175 DC Slide Gate Operator) and chain that would prevent it from being pulled past the wheel guide end point"], "keywords": [["gate was not complete", "missing the safety controls"]], "children": {"work_equipment_condition": {"type": "extraction", "text": ["gate was not complete, and it was missing the safety controls"], "keywords": [["gate was not complete", "missing the safety controls"]]}}}}}, "accident_type": {"type": "classification", "value": ["struck-by"]}}
 {"id": 131516.015, "accident_report": {"text": ["Employees #1 and #2 and coworkers, employed by a roofing and siding company, were working at the construction site of a new two-story residence. Employees #1 and #2 were repositioning a pump jack scaffold from the back of the house to another location. According to a coworker who witnessed the event, the two employees were in the process of laying down parallel to the house a 36-foot Alum-A-Pole, part of the scaffold system, when they appeared to lose control of the pole as a gust of wind came around the house's corner. The pole toppled onto energized overhead power lines 8 to 10 feet away, and electrical current flowed through the pole to the employees. Employee #1 was electrocuted. Employee #2 was transported to the hospital for treatment of electric shock injuries."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employees #1 and #2 and coworkers, employed by a roofing and siding company, were working at the construction site of a new two-story residence. Employees #1 and #2 were repositioning a pump jack scaffold from the back of the house to another location. According to a coworker who witnessed the event, the two employees were in the process of laying down parallel to the house a 36-foot Alum-A-Pole, part of the scaffold system"], "keywords": [["employed by a roofing and siding company", "construction site of a new two-story residence", "repositioning a pump jack scaffold", "laying down parallel to the house a 36-foot Alum-A-Pole"]], "children": {"construction_trade": {"type": "classification", "value": ["thermal and moisture protection"]}}}, "object_involved": {"type": "extraction", "text": ["power lines"], "keywords": [["power lines"]]}, "working_condition_factors": {"type": "extraction", "text": ["they appeared to lose control of the pole as a gust of wind came around the house's corner"], "keywords": [["gust of wind", "lose control of the pole"]], "children": {"weather_condition": {"type": "extraction", "text": ["lose control of the pole as a gust of wind came around"], "keywords": [["gust of wind", "lose control of the pole"]]}}}, "consequences": {"type": "extraction", "text": ["Employee #1 was electrocuted. Employee #2 was transported to the hospital for treatment of electric shock injuries"], "keywords": [["electrocuted", "electric shock injuries"]], "children": {"severity": {"type": "classification", "value": ["fatality"]}}}}}, "accident_type": {"type": "classification", "value": ["electrocution"]}}
 {"id": 131652.015, "accident_report": {"text": ["Employee #1, employed by a construction company, was working at a multiemployer construction project, the renovation of a multifamily residential building. The employee was tasked with replacing a section of plywood at the roof's eave. A lull material handler was being used to lift a box made on the job to the roof to deliver supplies to employees. The box was not properly secured to the lull, and when the employee stepped into the box to retrieve the plywood, the box fell off the lull's forks, causing the employee to fall. Employee #1 fell a height of 20 feet 4 inches. He sustained multiple blunt force traumatic injuries and was killed."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1, employed by a construction company, was working at a multiemployer construction project, the renovation of a multifamily residential building. The employee was tasked with replacing a section of plywood at the roof's eave. A lull material handler was being used to lift a box made on the job to the roof to deliver supplies to employees. The box was not properly secured to the lull, and when the employee stepped into the box to retrieve the plywood"], "keywords": [["employed by a construction company", "multiemployer construction project", "renovation of a multifamily residential building", "replacing a section of plywood at the roof's eave", "lull material handler", "stepped into the box to retrieve the plywood"]], "children": {"construction_trade": {"type": "classification", "value": ["wood, plastics, and composites"]}}}, "object_involved": {"type": "extraction", "text": ["box"], "keywords": [["box"]]}, "equipment_factors": {"type": "extraction", "text": ["box was not properly secured to the lull"], "keywords": [["box", "not properly secured to the lull"]], "children": {"work_equipment_condition": {"type": "extraction", "text": ["box was not properly secured to the lull"], "keywords": [["box", "not properly secured to the lull"]]}}}, "consequences": {"type": "extraction", "text": ["He sustained multiple blunt force traumatic injuries and was killed"], "keywords": [["sustained multiple blunt force traumatic injuries", "killed"]], "children": {"severity": {"type": "classification", "value": ["fatality"]}}}}}, "accident_type": {"type": "classification", "value": ["fall"]}}
 {"id": 131347.015, "accident_report": {"text": ["Employee #1, employed by a demolition and concrete contractor, was working at the site of a one-story plus basement multifamily apartment building that was being demolished. The employee was collecting lumber and trash to throw into an approximately 12-foot deep excavation where the concrete foundation and basement walls had been removed, exposing bare earth walls. The employee was working from a concrete and metal stairway. The stairway's support legs had been undermined at the edge of the excavation when a concrete wall had been removed. The stairway collapsed into the excavation, and the employee fell, a fall height of 10 feet, and struck his head and back on concrete debris at the bottom of the excavation. Emergency services transported the employee to the hospital, where he was admitted and treated for multiple injuries including a traumatic head injury and a severed spine. Employee #1 died at the hospital."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1, employed by a demolition and concrete contractor, was working at the site of a one-story plus basement multifamily apartment building that was being demolished. The employee was collecting lumber and trash to throw into an approximately 12-foot deep excavation where the concrete foundation and basement walls had been removed, exposing bare earth walls. The employee was working from a concrete and metal stairway"], "keywords": [["employed by a demolition and concrete contractor", "one-story plus basement multifamily apartment building that was being demolished", "collecting lumber and trash", "12-foot deep excavation", "concrete foundation and basement walls had been removed", "working from a concrete and metal stairway"]], "children": {"construction_trade": {"type": "classification", "value": ["existing conditions"]}}}, "object_involved": {"type": "extraction", "text": ["stairway"], "keywords": [["stairway"]]}, "working_condition_factors": {"type": "extraction", "text": ["stairway's support legs had been undermined at the edge of the excavation when a concrete wall had been removed"], "keywords": [["stairway's support legs", "undermined", "edge of the excavation"]], "children": {"workspace_condition": {"type": "extraction", "text": ["stairway's support legs had been undermined at the edge of the excavation"], "keywords": [["stairway's support legs", "undermined", "edge of the excavation"]]}}}, "consequences": {"type": "extraction", "text": ["he was admitted and treated for multiple injuries including a traumatic head injury and a severed spine. Employee #1 died"], "keywords": [["traumatic head injury", "severed spine", "died"]], "children": {"severity": {"type": "classification", "value": ["fatality"]}, "affected_body_part": {"type": "extraction", "text": ["head", "spine"], "keywords": [["head"], ["spine"]]}}}}}, "accident_type": {"type": "classification", "value": ["fall"]}}
@@ -224,7 +224,7 @@
 {"id": 122216.015, "accident_report": {"text": ["An employee was working as a structural metal worker for a structural steel and precast concrete contractor. He was erecting structural steel on a project of new work on or an addition to a hotel. The employee was part of a group of iron workers. They were working in the building's basement. A 30-foot tall (9.1-meter-tall), 14- or 14.5-inch-wide (356- or 368-mm-wide) column had been placed on a column pad. It was secured with three 1-1/2-inch (1.5-inch, or 38-mm) anchor bolts. There had been a fourth anchor bolt, but it had been broken off. Of the remaining anchor bolts, one had been cut off and rewelded in the field. The iron workers were connecting a horizontal beam to the freestanding column, which was held to the pad by only the three bolts. As the workers lowered the beam it got stuck and would not slide down in place. They began to pull the beam out to get a better angle for putting the beam into place. As they pulled the beam out, the column bolts broke off from the pad. The employee was straddling an adjacent beam, connecting the column to a support brace. The column fell into the beam that the employee was straddling. The column struck the employee's leg as it slid across the beam. The employee was knocked off the beam. His leg was struck either by the column or the beam as the column or beam fell past him. His femur was fractured. He was hospitalized. There were no guys or bracing in place (such as outlined in 1926.755(a)(4)) to keep the column erect and/or stabilized. The column was not adequately supported while the beam was being set in place. The violation was noted on or."], "children": {"working_circumstances": {"type": "extraction", "text": ["An employee was working as a structural metal worker for a structural steel and precast concrete contractor. He was erecting structural steel on a project of new work on or an addition to a hotel. The employee was part of a group of iron workers. They were working in the building's basement. A 30-foot tall (9.1-meter-tall), 14- or 14.5-inch-wide (356- or 368-mm-wide) column had been placed on a column pad. It was secured with three 1-1/2-inch (1.5-inch, or 38-mm) anchor bolts. There had been a fourth anchor bolt, but it had been broken off. Of the remaining anchor bolts, one had been cut off and rewelded in the field. The iron workers were connecting a horizontal beam to the freestanding column, which was held to the pad by only the three bolts"], "keywords": [["working as a structural metal worker", "structural steel and precast concrete contractor", "erecting structural steel", "addition to a hotel", "iron workers", "working in the building's basement", "30-foot tall (9.1-meter-tall), 14- or 14.5-inch-wide (356- or 368-mm-wide) column", "placed on a column pad", "secured with three 1-1/2-inch (1.5-inch, or 38-mm) anchor bolts", "fourth anchor bolt, but it had been broken off", "one had been cut off and rewelded in the field", "connecting a horizontal beam to the freestanding column", "held to the pad by only the three bolts"]], "children": {"construction_trade": {"type": "classification", "value": ["metals"]}}}, "object_involved": {"type": "extraction", "text": ["column"], "keywords": [["column"]]}, "working_condition_factors": {"type": "extraction", "text": ["There were no guys or bracing in place (such as outlined in 1926.755(a)(4)) to keep the column erect and/or stabilized. The column was not adequately supported while the beam was being set in place"], "keywords": [["no guys or bracing in place", "column", "not adequately supported"]], "children": {"workspace_condition": {"type": "extraction", "text": ["There were no guys or bracing in place", "column was not adequately supported"], "keywords": [["no guys or bracing in place"], ["column", "not adequately supported"]]}}}, "consequences": {"type": "extraction", "text": ["His femur was fractured"], "keywords": [["femur was fractured"]], "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}, "affected_body_part": {"type": "extraction", "text": ["femur"], "keywords": [["femur"]]}}}}}, "accident_type": {"type": "classification", "value": ["struck-by"]}}
 {"id": 125828.015, "accident_report": {"text": ["Two employees were working for a framing and drywall contractor. They were working at a multi-employer site. They were carpenters, part of a project of new work on or an addition to a six-story building, a hotel. They were installing bracing on the underside of a roof section that was suspended in the air from a crane. The roof section was 32 feet, 3 inches wide and 32 feet, 3 inches long (9.8 meters by 9.8 meters). It weighed 10,000 lbs. (4,500 kg). Four landscape timbers were being used as the rigging to lift the roof section. The landscape timbers had been run along the top chord of cold steel formed metal trusses, with no rigging securely holding the roof section in place. The landscape timbers had not been inspected. The load had not been rigged by a qualified rigger. The landscape timbers broke under the weight of the roof section, and the roof section fell from the crane. The roof section crushed the two employees They suffered fractures in the pelvis, legs, feet, and vertebrae. They were hospitalized. Investigation number 125828 brought up four entities, each with its own inspection number. Brevard Framing and Drywall, LLC had inspection number 1447010. PINKERTON & LAWS OF FLORIDA INC. had inspection number 1447025. Spinning Crane Works LLC had inspection number 1447030. AGUILA CONTRACTOR, LLC had inspection number 1472292. This account was based on the details for Brevard Framing and Drywall, LLC."], "children": {"working_circumstances": {"type": "extraction", "text": ["Two employees were working for a framing and drywall contractor. They were working at a multi-employer site. They were carpenters, part of a project of new work on or an addition to a six-story building, a hotel. They were installing bracing on the underside of a roof section that was suspended in the air from a crane"], "keywords": [["working for a framing and drywall contractor", "multi-employer site", "carpenters", "new work on or an addition to a six-story building, a hotel", "installing bracing on the underside of a roof section", "suspended in the air from a crane"]], "children": {"construction_trade": {"type": "classification", "value": ["finishes"]}}}, "object_involved": {"type": "extraction", "text": ["timbers"], "keywords": [["timbers"]]}, "managerial_factors": {"type": "extraction", "text": ["The landscape timbers had not been inspected. The load had not been rigged by a qualified rigger"], "keywords": [["landscape timbers", "not been inspected", "load", "not been rigged by a qualified rigger"]], "children": {"failure_of_hazard_management": {"type": "extraction", "text": ["The landscape timbers had not been inspected", "load had not been rigged by a qualified rigger"], "keywords": [["landscape timbers", "not been inspected"], ["load", "not been rigged by a qualified rigger"]]}}}, "working_condition_factors": {"type": "extraction", "text": ["landscape timbers had been run along the top chord of cold steel formed metal trusses, with no rigging securely holding the roof section in place"], "keywords": [["no rigging securely holding the roof section in place"]], "children": {"workspace_condition": {"type": "extraction", "text": ["no rigging securely holding the roof section in place"], "keywords": [["no rigging securely holding the roof section in place"]]}}}, "consequences": {"type": "extraction", "text": ["They suffered fractures in the pelvis, legs, feet, and vertebrae"], "keywords": [["fractures in the pelvis, legs, feet, and vertebrae"]], "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}, "affected_body_part": {"type": "extraction", "text": ["pelvis", "legs", "feet", "vertebrae"], "keywords": [["pelvis"], ["legs"], ["feet"], ["vertebrae"]]}}}}}, "accident_type": {"type": "classification", "value": ["caught-in/between"]}}
 {"id": 122833.015, "accident_report": {"text": ["Employee #1 was a construction laborer on the night crew, working as a fulltime employee for this employer. Employee #1 was standing alongside and under the G&Z paving machine, working in his required position when the paving machine is in operation and moving. Employee #1 was directly engaged in the operation of operating controls and levers to distribute the concrete from the ground to side to side. Employee #1 was on a crew laying down a stretch of lean base coat concrete (LBC), and the G&Z machine in this configuration runs faster than the other configurations. When the machine is set up in LBC mode, it runs approximately 15 feet/minute. The G&Z slip paving machine was operating without one of the mechanical drive guards in place. The employer took it off and had been running it this way for a while. Employee #1 was aware the guard was removed and questioned his supervisor but continued his duties. Employee #1 sustained an amputation to his big toe on the right foot. Employee #1 was hospitalized."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1 was a construction laborer on the night crew, working as a fulltime employee for this employer. Employee #1 was standing alongside and under the G&Z paving machine, working in his required position when the paving machine is in operation and moving. Employee #1 was directly engaged in the operation of operating controls and levers to distribute the concrete from the ground to side to side"], "keywords": [["a construction laborer on the night crew", "standing alongside and under the G&Z paving machine", "operating controls and levers to distribute the concrete"]], "children": {"construction_trade": {"type": "classification", "value": ["exterior improvements"]}}}, "object_involved": {"type": "extraction", "text": ["paving machine"], "keywords": [["paving machine"]]}, "equipment_factors": {"type": "extraction", "text": ["G&Z slip paving machine was operating without one of the mechanical drive guards in place"], "keywords": [["slip paving machine was operating without one of the mechanical drive guards in place"]], "children": {"work_equipment_condition": {"type": "extraction", "text": ["slip paving machine was operating without one of the mechanical drive guards in place"], "keywords": [["slip paving machine was operating without one of the mechanical drive guards in place"]]}}}, "consequences": {"type": "extraction", "text": ["Employee #1 sustained an amputation to his big toe on the right foot"], "keywords": [["amputation to his big toe on the right foot"]], "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}, "affected_body_part": {"type": "extraction", "text": ["big toe on the right foot"], "keywords": [["big toe on the right foot"]]}}}}}, "accident_type": {"type": "classification", "value": ["caught-in/between"]}}
-{"id": 125370.015, "accident_report": {"text": ["An employee working as a carpenter for a residential remodeler was working on a residential construction site. The employer has only 1 to 2 employees. The employee was repairing side panels on the south side of a house on a narrow walkway. A scaffold had been erected in the walkway, which was approximately three feet wide. The employee was using a nail gun when he stood up with his finger on the trigger. The employee inadvertently hit the trigger causing the nail gun to eject a nail into his left leg. The employee was experienced using nail guns. He was treated at the hospital and released on the same day."], "children": {"working_circumstances": {"type": "extraction", "text": ["An employee working as a carpenter for a residential remodeler was working on a residential construction site. The employer has only 1 to 2 employees. The employee was repairing side panels on the south side of a house on a narrow walkway. A scaffold had been erected in the walkway, which was approximately three feet wide. The employee was using a nail gun when he stood up with his finger on the trigger"], "keywords": [["working as a carpenter for a residential remodeler", "working on a residential construction site", "repairing side panels on the south side of a house", "narrow walkway", "scaffold had been erected in the walkway", "using a nail gun", "stood up with his finger on the trigger"]], "children": {"construction_trade": {"type": "classification", "value": ["wood, plastics, and composites"]}}}, "object_involved": {"type": "extraction", "text": ["nail"], "keywords": [["nail"]]}, "behavioral_factors": {"type": "extraction", "text": ["employee inadvertently hit the trigger causing the nail gun to eject a nail"], "keywords": [["inadvertently hit the trigger"]], "children": {"inattentive_behavior": {"type": "extraction", "text": ["inadvertently hit the trigger"], "keywords": [["inadvertently hit the trigger"]]}}}, "consequences": {"type": "extraction", "children": {"severity": {"type": "classification", "value": ["non hospitalized injury"]}}}}}, "accident_type": {"type": "classification", "value": ["struck-by"]}}
+{"id": 125370.015, "accident_report": {"text": ["An employee working as a carpenter for a residential remodeler was working on a residential construction site. The employer has only 1 to 2 employees. The employee was repairing side panels on the south side of a house on a narrow walkway. A scaffold had been erected in the walkway, which was approximately three feet wide. The employee was using a nail gun when he stood up with his finger on the trigger. The employee inadvertently hit the trigger causing the nail gun to eject a nail into his left leg. The employee was experienced using nail guns. He was treated at the hospital and released on the same day."], "children": {"working_circumstances": {"type": "extraction", "text": ["An employee working as a carpenter for a residential remodeler was working on a residential construction site. The employer has only 1 to 2 employees. The employee was repairing side panels on the south side of a house on a narrow walkway. A scaffold had been erected in the walkway, which was approximately three feet wide. The employee was using a nail gun when he stood up with his finger on the trigger"], "keywords": [["working as a carpenter for a residential remodeler", "working on a residential construction site", "repairing side panels on the south side of a house", "narrow walkway", "scaffold had been erected in the walkway", "using a nail gun", "stood up with his finger on the trigger"]], "children": {"construction_trade": {"type": "classification", "value": ["wood, plastics, and composites"]}}}, "object_involved": {"type": "extraction", "text": ["nail"], "keywords": [["nail"]]}, "behavioral_factors": {"type": "extraction", "text": ["employee inadvertently hit the trigger causing the nail gun to eject a nail"], "keywords": [["inadvertently hit the trigger"]], "children": {"inattentive_behavior": {"type": "extraction", "text": ["inadvertently hit the trigger"], "keywords": [["inadvertently hit the trigger"]]}}}}}, "accident_type": {"type": "classification", "value": ["struck-by"]}}
 {"id": 126745.015, "accident_report": {"text": ["An employee was working as a construction laborer for a landscaping architectural service. He was moving a wheelbarrow full of dirt. He lost his balance and fell onto a steel rebar. The rebar was capped with a cap that was not approved, designed, or intended for protection from impalement. The cap broke. Employee was punctured and impaled in his groin. He was hospitalized."], "children": {"working_circumstances": {"type": "extraction", "text": ["An employee was working as a construction laborer for a landscaping architectural service. He was moving a wheelbarrow full of dirt"], "keywords": [["working as a construction laborer for a landscaping architectural service", "moving a wheelbarrow full of dirt"]], "children": {"construction_trade": {"type": "classification", "value": ["earthwork"]}}}, "object_involved": {"type": "extraction", "text": ["rebar"], "keywords": [["rebar"]]}, "equipment_factors": {"type": "extraction", "text": ["rebar was capped with a cap that was not approved, designed, or intended for protection from impalement"], "keywords": [["rebar was capped with a cap", "not approved, designed, or intended for protection from impalement"]], "children": {"protective_equipment_condition": {"type": "extraction", "text": ["rebar was capped with a cap that was not approved, designed, or intended for protection from impalement"], "keywords": [["rebar was capped with a cap", "not approved, designed, or intended for protection from impalement"]]}}}, "consequences": {"type": "extraction", "text": ["Employee was punctured and impaled in his groin"], "keywords": [["punctured and impaled in his groin"]], "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}, "affected_body_part": {"type": "extraction", "text": ["groin"], "keywords": [["groin"]]}}}}}, "accident_type": {"type": "classification", "value": ["caught-in/between"]}}
 {"id": 121680.015, "accident_report": {"text": ["An employee working as a City Sewage Treatment Plant Operator was installing 8-inch PVC sewer line in a trench. A trench box was available since the trench was approximately 6 feet deep but it was not being used. The sidewall of the trench collapsed on the employee striking the employee and crushing him. The employee fractures all the ribs and sustained injuries to his lung on the right side of his body and was hospitalized."], "children": {"working_circumstances": {"type": "extraction", "text": ["An employee working as a City Sewage Treatment Plant Operator was installing 8-inch PVC sewer line in a trench"], "keywords": [["working as a City Sewage Treatment Plant Operator", "installing 8-inch PVC sewer line in a trench"]], "children": {"construction_trade": {"type": "classification", "value": ["utilities"]}}}, "object_involved": {"type": "extraction", "text": ["trench"], "keywords": [["trench"]]}, "behavioral_factors": {"type": "extraction", "text": ["trench box was available since the trench was approximately 6 feet deep but it was not being used"], "keywords": [["trench box was available", "not being used"]], "children": {"noncompliant_behavior": {"type": "extraction", "text": ["trench box was available since the trench was approximately 6 feet deep but it was not being used"], "keywords": [["trench box was available", "not being used"]]}}}, "consequences": {"type": "extraction", "text": ["employee fractures all the ribs and sustained injuries to his lung on the right side of his body"], "keywords": [["fractures all the ribs", "injuries to his lung on the right side of his body"]], "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}, "affected_body_part": {"type": "extraction", "text": ["ribs", "lung"], "keywords": [["ribs"], ["lung"]]}}}}}, "accident_type": {"type": "classification", "value": ["caught-in/between"]}}
 {"id": 125407.015, "accident_report": {"text": ["An employee working as a construction laborer for a water and sewer pipeline contractor was operating a SkilSaw Model SPT77W worm drive circular saw. The employee was using the saw to cut wedges from a 2-inch by 4-inch board. The employee had worked for the employer for approximately 8 years at the time. The employee is the foreman for the crew that included himself and five coworkers, three of which were laborers and two who were superintendents directing work at the site. The employee was kneeling while holding the board with one hand and the saw with his other hand. He was cutting his third wedge when the saw kicked back and struck his left hand. The employee stated that the board was approximately 1.5 feet long at the time and that he was using a couple pieces of the lumber to lean the work piece on while cutting the wedges. The employee had not secured the wood to a stable platform. The employee sustained fractures, contusions and lacerations to his hand and fingers and was hospitalized."], "children": {"working_circumstances": {"type": "extraction", "text": ["An employee working as a construction laborer for a water and sewer pipeline contractor was operating a SkilSaw Model SPT77W worm drive circular saw. The employee was using the saw to cut wedges from a 2-inch by 4-inch board. The employee had worked for the employer for approximately 8 years at the time. The employee is the foreman for the crew that included himself and five coworkers, three of which were laborers and two who were superintendents directing work at the site. The employee was kneeling while holding the board with one hand and the saw with his other hand"], "keywords": [["working as a construction laborer for a water and sewer pipeline contractor", "operating a SkilSaw Model SPT77W worm drive circular saw", "cut wedges from a 2-inch by 4-inch board", "kneeling while holding the board with one hand and the saw with his other hand"]], "children": {"construction_trade": {"type": "classification", "value": ["wood, plastics, and composites"]}}}, "object_involved": {"type": "extraction", "text": ["Saw"], "keywords": [["Saw"]]}, "working_condition_factors": {"type": "extraction", "text": ["he was using a couple pieces of the lumber to lean the work piece on while cutting the wedges. The employee had not secured the wood to a stable platform"], "keywords": [["not secured the wood to a stable platform"]], "children": {"workspace_condition": {"type": "extraction", "text": ["had not secured the wood to a stable platform"], "keywords": [["not secured the wood to a stable platform"]]}}}, "consequences": {"type": "extraction", "text": ["employee sustained fractures, contusions and lacerations to his hand and fingers"], "keywords": [["fractures, contusions and lacerations to his hand and fingers"]], "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}, "affected_body_part": {"type": "extraction", "text": ["hand", "fingers"], "keywords": [["hand"], ["fingers"]]}}}}}, "accident_type": {"type": "classification", "value": ["struck-by"]}}
@@ -280,7 +280,7 @@
 {"id": 114557.015, "accident_report": {"text": ["Employee #1 and coworkers, employed by an electrical contractor, were removing a metal streetlight pole. As a crane lifted the pole off its bolts in the foundation plate, Employee #1 used his hands to guide and stabilize the pole. During this lifting process, the metal pole rotated and came close - approximately 6 feet - to a 12.5-kilovolt distribution line. An electric arc flash occurred. The metal pole became energized, and the electric current, on its path to ground, crossed through the body of Employee #1. Emergency services transported Employee #1 to the hospital, where he was admitted and treated for electric shock and burns."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1 and coworkers, employed by an electrical contractor, were removing a metal streetlight pole. As a crane lifted the pole off its bolts in the foundation plate, Employee #1 used his hands to guide and stabilize the pole"], "keywords": [["employed by an electrical contractor", "removing a metal streetlight pole", "crane lifted the pole off its bolts in the foundation plate", "used his hands to guide and stabilize the pole"]], "children": {"construction_trade": {"type": "classification", "value": ["electrical"]}}}, "object_involved": {"type": "extraction", "text": ["distribution line"], "keywords": [["distribution line"]]}, "working_condition_factors": {"type": "extraction", "text": ["metal pole rotated and came close - approximately 6 feet - to a 12.5-kilovolt distribution line"], "keywords": [["metal pole rotated", "came close - approximately 6 feet - to a 12.5-kilovolt distribution line"]], "children": {"workspace_condition": {"type": "extraction", "text": ["metal pole rotated and came close - approximately 6 feet - to a 12.5-kilovolt distribution line"], "keywords": [["metal pole rotated", "came close - approximately 6 feet - to a 12.5-kilovolt distribution line"]]}}}, "consequences": {"type": "extraction", "text": ["he was admitted and treated for electric shock and burns"], "keywords": [["electric shock", "burns"]], "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}}}}}, "accident_type": {"type": "classification", "value": ["electrocution"]}}
 {"id": 114510.015, "accident_report": {"text": ["Employee #1, employed by an electrical contractor, was working at a multiemployer project, the renovation of an office building. He was taking measurements to determine the amount of wire needed to run wire into an electrical panel. When the employee attempted to replace the cover for the upper section of the panel, the cover did not seat properly. The cover fell into the panel and struck energized equipment inside. An arc flash ensued, and Employee #1's face was burned. Emergency services transported the employee to the hospital, where he was admitted and treated for first and second degree burns to his face."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1, employed by an electrical contractor, was working at a multiemployer project, the renovation of an office building. He was taking measurements to determine the amount of wire needed to run wire into an electrical panel. When the employee attempted to replace the cover for the upper section of the panel"], "keywords": [["employed by an electrical contractor", "multiemployer project", "renovation of an office building", "taking measurements to determine the amount of wire", "run wire into an electrical panel", "replace the cover for the upper section of the panel"]], "children": {"construction_trade": {"type": "classification", "value": ["electrical"]}}}, "object_involved": {"type": "extraction", "text": ["energized equipment"], "keywords": [["energized equipment"]]}, "equipment_factors": {"type": "extraction", "text": ["cover did not seat properly"], "keywords": [["cover did not seat properly"]], "children": {"work_equipment_condition": {"type": "extraction", "text": ["cover did not seat properly"], "keywords": [["cover did not seat properly"]]}}}, "consequences": {"type": "extraction", "text": ["he was admitted and treated for first and second degree burns to his face"], "keywords": [["first and second degree burns to his face"]], "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}, "affected_body_part": {"type": "extraction", "text": ["face"], "keywords": [["face"]]}}}}}, "accident_type": {"type": "classification", "value": ["electrocution"]}}
 {"id": 111441.015, "accident_report": {"text": ["An employee was working for a manufacturer of sheet metal work. He was receiving a piece of metal flashing from a worker on the ground. As he was receiving the metal flashing, a gust of wind blew the flashing into an overhead power line. The line was energized at 19 kilovolts (kV). The employee sustained an electric shock. He was hospitalized for two or more days."], "children": {"working_circumstances": {"type": "extraction", "text": ["An employee was working for a manufacturer of sheet metal work. He was receiving a piece of metal flashing from a worker on the ground"], "keywords": [["working for a manufacturer of sheet metal work", "receiving a piece of metal flashing from a worker on the ground"]], "children": {"construction_trade": {"type": "classification", "value": ["thermal and moisture protection"]}}}, "object_involved": {"type": "extraction", "text": ["power line"], "keywords": [["power line"]]}, "working_condition_factors": {"type": "extraction", "text": ["gust of wind blew the flashing into an overhead power line"], "keywords": [["gust of wind", "blew the flashing"]], "children": {"weather_condition": {"type": "extraction", "text": ["gust of wind blew the flashing"], "keywords": [["gust of wind", "blew the flashing"]]}}}, "consequences": {"type": "extraction", "text": ["The employee sustained an electric shock"], "keywords": [["sustained an electric shock"]], "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}}}}}, "accident_type": {"type": "classification", "value": ["electrocution"]}}
-{"id": 115601.015, "accident_report": {"text": ["Employee #1, a superintendent employed by a construction company, was engaged in electrical work at a seven-story hospital. He was tracing an electrical line for an x-ray \"in use\" light fixture in an above-ceiling crawlspace. He had recently tested the wiring and was aware it was energized. As the employee proceeded with tracing the line without de-energizing the circuit, he received an electric shock from 277/480-volt energized conductors. The employee lost consciousness. Firefighters and emergency medical technicians arrived but were delayed from providing services for approximately 10 minutes while the electricity to the area was turned off. They then extracted the employee through an 18-inch access hatch. The employee required hospitalization for approximately one month."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1, a superintendent employed by a construction company, was engaged in electrical work at a seven-story hospital. He was tracing an electrical line for an x-ray \"in use\" light fixture in an above-ceiling crawlspace. He had recently tested the wiring and was aware it was energized"], "keywords": [["superintendent employed by a construction company", "electrical work at a seven-story hospital", "tracing an electrical line for an x-ray", "above-ceiling crawlspace", "tested the wiring", "aware it was energized"]], "children": {"construction_trade": {"type": "classification", "value": ["electrical"]}}}, "object_involved": {"type": "extraction", "text": ["conductors"], "keywords": [["conductors"]]}, "behavioral_factors": {"type": "extraction", "text": ["He had recently tested the wiring and was aware it was energized. As the employee proceeded with tracing the line without de-energizing the circuit"], "keywords": [["proceeded with tracing the line", "without de-energizing the circuit"]], "children": {"noncompliant_behavior": {"type": "extraction", "text": ["proceeded with tracing the line without de-energizing the circuit"], "keywords": [["proceeded with tracing the line", "without de-energizing the circuit"]]}}}, "consequences": {"type": "extraction", "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}}}}}, "accident_type": {"type": "classification", "value": ["electrocution"]}}
+{"id": 115601.015, "accident_report": {"text": ["Employee #1, a superintendent employed by a construction company, was engaged in electrical work at a seven-story hospital. He was tracing an electrical line for an x-ray \"in use\" light fixture in an above-ceiling crawlspace. He had recently tested the wiring and was aware it was energized. As the employee proceeded with tracing the line without de-energizing the circuit, he received an electric shock from 277/480-volt energized conductors. The employee lost consciousness. Firefighters and emergency medical technicians arrived but were delayed from providing services for approximately 10 minutes while the electricity to the area was turned off. They then extracted the employee through an 18-inch access hatch. The employee required hospitalization for approximately one month."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1, a superintendent employed by a construction company, was engaged in electrical work at a seven-story hospital. He was tracing an electrical line for an x-ray \"in use\" light fixture in an above-ceiling crawlspace. He had recently tested the wiring and was aware it was energized"], "keywords": [["superintendent employed by a construction company", "electrical work at a seven-story hospital", "tracing an electrical line for an x-ray", "above-ceiling crawlspace", "tested the wiring", "aware it was energized"]], "children": {"construction_trade": {"type": "classification", "value": ["electrical"]}}}, "object_involved": {"type": "extraction", "text": ["conductors"], "keywords": [["conductors"]]}, "behavioral_factors": {"type": "extraction", "text": ["He had recently tested the wiring and was aware it was energized. As the employee proceeded with tracing the line without de-energizing the circuit"], "keywords": [["proceeded with tracing the line", "without de-energizing the circuit"]], "children": {"noncompliant_behavior": {"type": "extraction", "text": ["proceeded with tracing the line without de-energizing the circuit"], "keywords": [["proceeded with tracing the line", "without de-energizing the circuit"]]}}}}}, "accident_type": {"type": "classification", "value": ["electrocution"]}}
 {"id": 108989.015, "accident_report": {"text": ["Employee #1, employed by an HVAC services company, was attempting to service an HVAC unit in the attic of a single family residence. He was using a 10-foot Type IA Louisville Aluminum A-frame ladder to access the attic entry, although the distance from floor to entry was 12 feet, exceeding the ladder's height. The employee climbed the ladder and then jumped up from the ladder's top cap into the entry opening. He became wedged in the opening, and then slipped out and fell to the floor, a fall height of 12 feet. The employee was transported to the hospital, admitted, and treated for a head laceration."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1, employed by an HVAC services company, was attempting to service an HVAC unit in the attic of a single family residence. He was using a 10-foot Type IA Louisville Aluminum A-frame ladder to access the attic entry"], "keywords": [["employed by an HVAC services company", "service an HVAC unit in the attic of a single family residence", "using a 10-foot Type IA Louisville Aluminum A-frame ladder to access the attic entry"]], "children": {"construction_trade": {"type": "classification", "value": ["heating, ventilating, and air conditioning (hvac)"]}}}, "object_involved": {"type": "extraction", "text": ["ladder"], "keywords": [["ladder"]]}, "behavioral_factors": {"type": "extraction", "text": ["employee climbed the ladder and then jumped up from the ladder's top cap into the entry opening"], "keywords": [["jumped up from the ladder's top cap"]], "children": {"noncompliant_behavior": {"type": "extraction", "text": ["jumped up from the ladder's top cap"], "keywords": [["jumped up from the ladder's top cap"]]}}}, "consequences": {"type": "extraction", "text": ["head laceration"], "keywords": [["head laceration"]], "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}, "affected_body_part": {"type": "extraction", "text": ["head"], "keywords": [["head"]]}}}}}, "accident_type": {"type": "classification", "value": ["fall"]}}
 {"id": 113362.015, "accident_report": {"text": ["Employee #1 and a Coworker, employed by a framing construction contractor, were working on the construction of three houses. The coworker, who was foreman and forklift operator, instructed Employee #1 to climb onto the JLG Telescopic Forklift, Model G10-55A, Serial Number 2015103-01, and ride it up to remove the outriggers from the three houses. During this operation at the second house, Employee #1 was lifted to the roof, where he removed two wooden planks from the roof and placed them onto the fork blades, to be used as a work platform. Employee #1 then stood on the two wooden planks and was lowered approximately 5 to 8 feet below the roof eaves to remove the outriggers. As he removed two outriggers, the forklift moved backward and jerked. Employee #1 lost his balance and stepped onto the plank beyond the fork blade. The plank tipped over, and Employee #1 fell, a fall height of approximately 15 feet. Employee #1 was transported to the hospital and admitted for treatment of injuries to his left femur (thighbone), left arm, left wrist, right arm, right wrist, and his back."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1 and a Coworker, employed by a framing construction contractor, were working on the construction of three houses. The coworker, who was foreman and forklift operator, instructed Employee #1 to climb onto the JLG Telescopic Forklift, Model G10-55A, Serial Number 2015103-01, and ride it up to remove the outriggers from the three houses. During this operation at the second house, Employee #1 was lifted to the roof, where he removed two wooden planks from the roof and placed them onto the fork blades, to be used as a work platform. Employee #1 then stood on the two wooden planks and was lowered approximately 5 to 8 feet below the roof eaves to remove the outriggers"], "keywords": [["employed by a framing construction contractor", "construction of three houses", "foreman and forklift operator", "instructed Employee #1 to climb onto the JLG Telescopic Forklift", "ride it up to remove the outriggers", "removed two wooden planks from the roof", "placed them onto the fork blades", "work platform", "lowered approximately 5 to 8 feet below the roof eaves"]], "children": {"construction_trade": {"type": "classification", "value": ["wood, plastics, and composites"]}}}, "object_involved": {"type": "extraction", "text": ["plank"], "keywords": [["plank"]]}, "behavioral_factors": {"type": "extraction", "text": ["coworker, who was foreman and forklift operator, instructed Employee #1 to climb onto the JLG Telescopic Forklift, Model G10-55A, Serial Number 2015103-01, and ride it up to remove the outriggers from the three houses", "he removed two wooden planks from the roof and placed them onto the fork blades, to be used as a work platform"], "keywords": [["instructed Employee #1 to climb onto the JLG Telescopic Forklift", "ride it"], ["wooden planks from the roof", "placed them onto the fork blades", "work platform"]], "children": {"noncompliant_behavior": {"type": "extraction", "text": ["instructed Employee #1 to climb onto the JLG Telescopic Forklift, Model G10-55A, Serial Number 2015103-01, and ride it", "wooden planks from the roof and placed them onto the fork blades, to be used as a work platform"], "keywords": [["instructed Employee #1 to climb onto the JLG Telescopic Forklift", "ride it"], ["wooden planks from the roof", "placed them onto the fork blades", "work platform"]]}}}, "consequences": {"type": "extraction", "text": ["admitted for treatment of injuries to his left femur (thighbone), left arm, left wrist, right arm, right wrist, and his back"], "keywords": [["injuries to his left femur (thighbone), left arm, left wrist, right arm, right wrist, and his back"]], "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}, "affected_body_part": {"type": "extraction", "text": ["left femur (thighbone)", "left arm", "left wrist", "right arm", "right wrist", "back"], "keywords": [["left femur (thighbone)"], ["left arm"], ["left wrist"], ["right arm"], ["right wrist"], ["back"]]}}}}}, "accident_type": {"type": "classification", "value": ["fall"]}}
 {"id": 115727.015, "accident_report": {"text": ["Employee #1, employed by a concrete construction company, was engaged in construction of concrete parking structures. He was handling the rubber hose, 4-5 inches in diameter, that is used to deliver concrete slurry from a concrete boom truck to the pour location. As pumping resumed after a down time, there was a surge in the hose line as a clog cleared, and the hose whipped violently due to the release of energy/pressure that had built up. The hose struck the employee on the left side of his head, then whipped back and struck and fractured his right clavicle/shoulder bone. The employee was transported to the hospital and admitted for treatment of the fractured shoulder."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1, employed by a concrete construction company, was engaged in construction of concrete parking structures. He was handling the rubber hose, 4-5 inches in diameter, that is used to deliver concrete slurry from a concrete boom truck to the pour location"], "keywords": [["employed by a concrete construction company", "construction of concrete parking structures", "handling the rubber hose", "deliver concrete slurry from a concrete boom truck to the pour location"]], "children": {"construction_trade": {"type": "classification", "value": ["concrete"]}}}, "object_involved": {"type": "extraction", "text": ["hose"], "keywords": [["hose"]]}, "equipment_factors": {"type": "extraction", "text": ["As pumping resumed after a down time, there was a surge in the hose line as a clog cleared, and the hose whipped violently due to the release of energy/pressure that had built up"], "keywords": [["surge in the hose line as a clog cleared"]], "children": {"work_equipment_condition": {"type": "extraction", "text": ["there was a surge in the hose line as a clog cleared"], "keywords": [["surge in the hose line as a clog cleared"]]}}}, "consequences": {"type": "extraction", "text": ["admitted for treatment of the fractured shoulder"], "keywords": [["fractured shoulder"]], "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}, "affected_body_part": {"type": "extraction", "text": ["shoulder"], "keywords": [["shoulder"]]}}}}}, "accident_type": {"type": "classification", "value": ["struck-by"]}}
@@ -412,7 +412,7 @@
 {"id": 105132.015, "accident_report": {"text": ["Employee #1, employed by a construction company, was working at a multiemployer construction project, a one-story commercial structure. He was working from an aerial lift in windy conditions and attempting to install metal siding on a wall. Employee #1 fell from the lift, a fall height of 20 feet. Emergency services were called, and Employee #1 was transported to the hospital. He was admitted and treated for fractures to both wrists."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1, employed by a construction company, was working at a multiemployer construction project, a one-story commercial structure. He was working from an aerial lift in windy conditions and attempting to install metal siding on a wall"], "keywords": [["employed by a construction company", "multiemployer construction project", "one-story commercial structure", "working from an aerial lift in windy conditions", "install metal siding on a wall"]], "children": {"construction_trade": {"type": "classification", "value": ["thermal and moisture protection"]}}}, "object_involved": {"type": "extraction", "text": ["lift"], "keywords": [["lift"]]}, "working_condition_factors": {"type": "extraction", "text": ["in windy conditions"], "keywords": [["windy conditions"]], "children": {"weather_condition": {"type": "extraction", "text": ["windy conditions"], "keywords": [["windy conditions"]]}}}, "consequences": {"type": "extraction", "text": ["He was admitted and treated for fractures to both wrists"], "keywords": [["fractures to both wrists"]], "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}, "affected_body_part": {"type": "extraction", "text": ["wrists"], "keywords": [["wrists"]]}}}}}, "accident_type": {"type": "classification", "value": ["fall"]}}
 {"id": 103240.015, "accident_report": {"text": ["Employee #1, employed by a pipeline company, was connecting pipes inside a trench. The soil was saturated due to rainy weather. In addition, the trench box was set 4.83 feet above the bottom surface, which exceeded the allowable 2-foot gap. A trench wall caved in, and a large quantity of saturated soil landed on Employee #1's foot. Emergency services were called, and Employee #1 was transported to the hospital. He was admitted and treated for a fractured ankle."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1, employed by a pipeline company, was connecting pipes inside a trench"], "keywords": [["employed by a pipeline company", "connecting pipes inside a trench"]], "children": {"construction_trade": {"type": "classification", "value": ["utilities"]}}}, "object_involved": {"type": "extraction", "text": ["soil"], "keywords": [["soil"]]}, "working_condition_factors": {"type": "extraction", "text": ["soil was saturated due to rainy weather"], "keywords": [["soil was saturated", "rainy weather"]], "children": {"weather_condition": {"type": "extraction", "text": ["soil was saturated due to rainy weather"], "keywords": [["soil was saturated", "rainy weather"]]}}}, "consequences": {"type": "extraction", "text": ["He was admitted and treated for a fractured ankle"], "keywords": [["fractured ankle"]], "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}, "affected_body_part": {"type": "extraction", "text": ["ankle"], "keywords": [["ankle"]]}}}}}, "accident_type": {"type": "classification", "value": ["caught-in/between"]}}
 {"id": 103140.015, "accident_report": {"text": ["Employee #1, employed by an electrical services company, was working from an aerial lift and engaged in maintenance work on an energized high voltage power line. Employee #1 sustained an electric shock and burn. Employee #1 was wearing the appropriate rubber and leather gloves, but the gloves were found to have holes in the left thumb after the incident. Emergency services were called, and Employee #1 was transported to the hospital, where he was admitted and treated for second degree electric burns to his left thumb, left leg near the ankle, and left thigh."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1, employed by an electrical services company, was working from an aerial lift and engaged in maintenance work on an energized high voltage power line"], "keywords": [["employed by an electrical services company", "working from an aerial lift", "maintenance work on an energized high voltage power line"]], "children": {"construction_trade": {"type": "classification", "value": ["electrical"]}}}, "object_involved": {"type": "extraction", "text": ["power line"], "keywords": [["power line"]]}, "equipment_factors": {"type": "extraction", "text": ["gloves were found to have holes in the left thumb after the incident"], "keywords": [["gloves were found to have holes in the left thumb"]], "children": {"protective_equipment_condition": {"type": "extraction", "text": ["gloves were found to have holes in the left thumb"], "keywords": [["gloves were found to have holes in the left thumb"]]}}}, "consequences": {"type": "extraction", "text": ["he was admitted and treated for second degree electric burns to his left thumb, left leg near the ankle, and left thigh"], "keywords": [["second degree electric burns to his left thumb, left leg near the ankle, and left thigh"]], "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}, "affected_body_part": {"type": "extraction", "text": ["left thumb", "left leg near the ankle", "left thigh"], "keywords": [["left thumb"], ["left leg near the ankle"], ["left thigh"]]}}}}}, "accident_type": {"type": "classification", "value": ["electrocution"]}}
-{"id": 103300.015, "accident_report": {"text": ["Employee #1 and Coworker #1, employed by a construction company, were engaged in trenching work. Coworker #1 was operating an excavator and lifting the excavator's bucket, which was full of gravel from the trench being dug. Employee #1 was holding plastic coverings down near the trench to collect the gravel. Coworker #1, as the result of a distraction, shut off the excavator with the bucket positioned mid-air and directly above Employee #1. The hydraulic system valve failed, and the bucket's load of gravel was released. Employee #1 was struck in the back by the falling gravel and the rear end of the bucket, and he fell into the trench. Emergency services were called, and Employee #1 was transported to the hospital, where he was treated and released."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1 and Coworker #1, employed by a construction company, were engaged in trenching work. Coworker #1 was operating an excavator and lifting the excavator's bucket, which was full of gravel from the trench being dug. Employee #1 was holding plastic coverings down near the trench to collect the gravel. Coworker #1, as the result of a distraction, shut off the excavator with the bucket positioned mid-air and directly above Employee #1"], "keywords": [["employed by a construction company", "trenching work", "operating an excavator", "lifting the excavator's bucket", "full of gravel from the trench", "holding plastic coverings down near the trench", "collect the gravel", "distraction", "shut off the excavator with the bucket positioned mid-air", "directly above Employee #1"]], "children": {"construction_trade": {"type": "classification", "value": ["earthwork"]}}}, "object_involved": {"type": "extraction", "text": ["gravel", "bucket"], "keywords": [["gravel"], ["bucket"]]}, "working_condition_factors": {"type": "extraction", "text": ["bucket positioned mid-air and directly above Employee #1"], "keywords": [["bucket positioned mid-air", "directly above Employee #1"]], "children": {"workspace_condition": {"type": "extraction", "text": ["bucket positioned mid-air and directly above Employee #1"], "keywords": [["bucket positioned mid-air", "directly above Employee #1"]]}}}, "equipment_factors": {"type": "extraction", "text": ["hydraulic system valve failed"], "keywords": [["hydraulic system valve", "failed"]], "children": {"work_equipment_condition": {"type": "extraction", "text": ["hydraulic system valve failed"], "keywords": [["hydraulic system valve", "failed"]]}}}, "behavioral_factors": {"type": "extraction", "text": ["Coworker #1, as the result of a distraction"], "keywords": [["distraction"]], "children": {"inattentive_behavior": {"type": "extraction", "text": ["distraction"], "keywords": [["distraction"]]}}}, "consequences": {"type": "extraction", "children": {"severity": {"type": "classification", "value": ["non hospitalized injury"]}}}}}, "accident_type": {"type": "classification", "value": ["struck-by"]}}
+{"id": 103300.015, "accident_report": {"text": ["Employee #1 and Coworker #1, employed by a construction company, were engaged in trenching work. Coworker #1 was operating an excavator and lifting the excavator's bucket, which was full of gravel from the trench being dug. Employee #1 was holding plastic coverings down near the trench to collect the gravel. Coworker #1, as the result of a distraction, shut off the excavator with the bucket positioned mid-air and directly above Employee #1. The hydraulic system valve failed, and the bucket's load of gravel was released. Employee #1 was struck in the back by the falling gravel and the rear end of the bucket, and he fell into the trench. Emergency services were called, and Employee #1 was transported to the hospital, where he was treated and released."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1 and Coworker #1, employed by a construction company, were engaged in trenching work. Coworker #1 was operating an excavator and lifting the excavator's bucket, which was full of gravel from the trench being dug. Employee #1 was holding plastic coverings down near the trench to collect the gravel. Coworker #1, as the result of a distraction, shut off the excavator with the bucket positioned mid-air and directly above Employee #1"], "keywords": [["employed by a construction company", "trenching work", "operating an excavator", "lifting the excavator's bucket", "full of gravel from the trench", "holding plastic coverings down near the trench", "collect the gravel", "distraction", "shut off the excavator with the bucket positioned mid-air", "directly above Employee #1"]], "children": {"construction_trade": {"type": "classification", "value": ["earthwork"]}}}, "object_involved": {"type": "extraction", "text": ["gravel", "bucket"], "keywords": [["gravel"], ["bucket"]]}, "working_condition_factors": {"type": "extraction", "text": ["bucket positioned mid-air and directly above Employee #1"], "keywords": [["bucket positioned mid-air", "directly above Employee #1"]], "children": {"workspace_condition": {"type": "extraction", "text": ["bucket positioned mid-air and directly above Employee #1"], "keywords": [["bucket positioned mid-air", "directly above Employee #1"]]}}}, "equipment_factors": {"type": "extraction", "text": ["hydraulic system valve failed"], "keywords": [["hydraulic system valve", "failed"]], "children": {"work_equipment_condition": {"type": "extraction", "text": ["hydraulic system valve failed"], "keywords": [["hydraulic system valve", "failed"]]}}}, "behavioral_factors": {"type": "extraction", "text": ["Coworker #1, as the result of a distraction"], "keywords": [["distraction"]], "children": {"inattentive_behavior": {"type": "extraction", "text": ["distraction"], "keywords": [["distraction"]]}}}}}, "accident_type": {"type": "classification", "value": ["struck-by"]}}
 {"id": 103279.015, "accident_report": {"text": ["Employee #1 and Coworkers #1 and #2, employed by a construction company, were working at a multiemployer construction project, a one-story commercial building. After helping to cut and rig metal decking for hoisting by crane to the structure's roof, Employee #1 was sent to the roof to assist Coworkers #1 and #2, who were installing the roof decking. The decking had oil on its surface and, due to the weather, also had surface ice. While standing on the decking and tacking it into place, Employee #1 slipped and fell between the joists to the concrete surface, a fall height of 16 feet. Emergency services were called, and Employee #1 was transported to the hospital, admitted, and treated for fractures to his wrist and elbow and a laceration and contusion to his head."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1 and Coworkers #1 and #2, employed by a construction company, were working at a multiemployer construction project, a one-story commercial building. After helping to cut and rig metal decking for hoisting by crane to the structure's roof, Employee #1 was sent to the roof to assist Coworkers #1 and #2, who were installing the roof decking. The decking had oil on its surface and, due to the weather, also had surface ice. While standing on the decking and tacking it into place"], "keywords": [["employed by a construction company", "multiemployer construction project", "one-story commercial building", "cut and rig metal decking for hoisting by crane to the structure's roof", "installing the roof decking", "decking had oil on its surface", "surface ice", "standing on the decking and tacking it into place"]], "children": {"construction_trade": {"type": "classification", "value": ["metals"]}}}, "object_involved": {"type": "extraction", "text": ["joists"], "keywords": [["joists"]]}, "working_condition_factors": {"type": "extraction", "text": ["decking had oil on its surface and, due to the weather, also had surface ice"], "keywords": [["the weather", "surface ice", "decking", "had oil on its surface"]], "children": {"weather_condition": {"type": "extraction", "text": ["due to the weather, also had surface ice"], "keywords": [["the weather", "surface ice"]]}, "workspace_condition": {"type": "extraction", "text": ["decking had oil on its surface"], "keywords": [["decking", "had oil on its surface"]]}}}, "consequences": {"type": "extraction", "text": ["admitted, and treated for fractures to his wrist and elbow and a laceration and contusion to his head"], "keywords": [["fractures to his wrist and elbow", "laceration and contusion to his head"]], "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}, "affected_body_part": {"type": "extraction", "text": ["wrist", "elbow", "head"], "keywords": [["wrist"], ["elbow"], ["head"]]}}}}}, "accident_type": {"type": "classification", "value": ["fall"]}}
 {"id": 104503.015, "accident_report": {"text": ["Employee #1, employed by a construction company, was working at a multifamily residential building that was being renovated. He was operating a grinder machine and using an extension cord that was not grounded and that was in contact with a wet surface. The extension cord was connected to a non-GFCI source. Employee #1 incurred an electric shock and fell unconscious to the floor. Emergency services were called, and Employee #1 was transported to the hospital. He was admitted and treated for electric shock injuries."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1, employed by a construction company, was working at a multifamily residential building that was being renovated. He was operating a grinder machine and using an extension cord"], "keywords": [["employed by a construction company", "multifamily residential building that was being renovated", "operating a grinder machine", "using an extension cord"]]}, "object_involved": {"type": "extraction", "text": ["extension cord"], "keywords": [["extension cord"]]}, "working_condition_factors": {"type": "extraction", "text": ["extension cord that was not grounded and that was in contact with a wet surface. The extension cord was connected to a non-GFCI source"], "keywords": [["wet surface"]], "children": {"workspace_condition": {"type": "extraction", "text": ["wet surface"], "keywords": [["wet surface"]]}}}, "equipment_factors": {"type": "extraction", "text": ["extension cord that was not grounded"], "keywords": [["extension cord", "not grounded"]], "children": {"work_equipment_condition": {"type": "extraction", "text": ["extension cord that was not grounded"], "keywords": [["extension cord", "not grounded"]]}}}, "consequences": {"type": "extraction", "text": ["He was admitted and treated for electric shock injuries"], "keywords": [["electric shock injuries"]], "children": {"severity": {"type": "classification", "value": ["hospitalized injury"]}}}}}, "accident_type": {"type": "classification", "value": ["electrocution"]}}
 {"id": 105012.015, "accident_report": {"text": ["Employee #1 was setting up a chain link fence fabrication machine. The process required the unguarded machine's parts to be moving. Employee #1's sweatshirt caught on a bolt protruding from an unguarded rotating shaft, and his arm was pulled into the moving machine. A fuse blew and caused the machine to stop. Emergency services were called, and Employee #1 was transported to the hospital. He was admitted and treated for two fractures to his forearm."], "children": {"working_circumstances": {"type": "extraction", "text": ["Employee #1 was setting up a chain link fence fabrication machine"], "keywords": [["setting up a chain link fence fabrication machine"]], "children": {"construction_trade": {"type": "classification", "value": ["exterior improvements"]}}}, "object_involved": {"type": "extraction", "text": ["fence fabrication machine"], "keywords": [["fence fabrication machine"]]}, "equipment_factors": {"type": "extraction", "text": ["unguarded machine's parts", "bolt protruding from an unguarded rotating shaft"], "keywords": [["unguarded machine's parts"], ["bolt protruding from an unguarded rotating shaft"]], "children": {"work_equipment_condition": {"type": "extraction", "text": ["unguarded machine's parts", "bolt protruding from an unguarded rotating shaft"], "keywords": [["unguarded machine's parts"], ["bolt protruding from an unguarded rotating shaft"]]}}}, "consequences": {"type": "extraction", "text": ["He was admitted and treated for two fractures to his forearm"], "keywords": [["two fractures to his forearm"]], "children": {"severity": {"type": "classification", "value": ["non hospitalized injury"]}, "affected_body_part": {"type": "extraction", "text": ["forearm"], "keywords": [["forearm"]]}}}}}, "accident_type": {"type": "classification", "value": ["caught-in/between"]}}