import streamlit as st

# Function to convert all units to square meters
def convert_to_sqm(length, width, unit):
    if unit == "Meters (m)":
        return length * width
    elif unit == "Centimeters (cm)":
        return (length / 100) * (width / 100)
    elif unit == "Millimeters (mm)":
        return (length / 1000) * (width / 1000)

# Function to calculate required C Channels/Rods based on spacing
def calculate_c_channels(area, rod_length, horizontal_spacing, vertical_spacing):
    if rod_length <= 0 or horizontal_spacing <= 0 or vertical_spacing <= 0:
        return None
    
    # Calculate number of rods required in horizontal and vertical directions
    horizontal_rods = area / horizontal_spacing
    vertical_rods = area / vertical_spacing

    # Calculate total rods required based on their length
    total_rods = (horizontal_rods + vertical_rods) / rod_length
    return total_rods

# Streamlit UI Configuration
st.set_page_config(page_title="Area, Gypsum Board & C Channel Calculator", layout="wide")

st.title("📐 Multi-Purpose Calculator")
st.markdown("Calculate area, gypsum board requirements, and C Channel/Rod usage.")

# Section 1: Area Calculation
st.subheader("🔹 Main Area Input")
unit = st.selectbox("Select the unit of measurement:", ["Meters (m)", "Centimeters (cm)", "Millimeters (mm)"])

length = st.number_input("Enter Length:", min_value=0.0, format="%.2f")
width = st.number_input("Enter Width:", min_value=0.0, format="%.2f")

# Calculate area
total_area = convert_to_sqm(length, width, unit)

# Option to subtract an excluded area
st.subheader("🔹 Excluded Area (Optional)")
exclude_length = st.number_input("Enter Length of Excluded Area:", min_value=0.0, format="%.2f", key="ex_len")
exclude_width = st.number_input("Enter Width of Excluded Area:", min_value=0.0, format="%.2f", key="ex_wid")

excluded_area = convert_to_sqm(exclude_length, exclude_width, unit)
final_area = total_area - excluded_area

st.markdown(f"### ✅ Total Area: `{final_area:.2f} m²`")

# Section 2: Gypsum Board Calculation
st.subheader("🛠 Gypsum Board Calculation")
gypsum_board_area = st.number_input("Enter Area of a Single Gypsum Board (m²):", min_value=0.1, format="%.2f")

if st.button("Calculate Required Gypsum Boards"):
    if gypsum_board_area > 0:
        num_boards = final_area / gypsum_board_area
        st.success(f"📌 You will need approximately `{num_boards:.2f}` gypsum boards.")
    else:
        st.error("Please enter a valid gypsum board area.")

# Section 3: Direct Area Input for Gypsum Board Calculation
st.subheader("📏 Enter a Custom Area for Gypsum Board Calculation")
custom_area = st.number_input("Enter Total Area in m²:", min_value=0.0, format="%.2f", key="custom_area")

if st.button("Calculate Required Gypsum Boards (Based on Custom Area)"):
    if gypsum_board_area > 0:
        num_boards_custom = custom_area / gypsum_board_area
        st.success(f"📌 You will need approximately `{num_boards_custom:.2f}` gypsum boards.")
    else:
        st.error("Please enter a valid gypsum board area.")

# Section 4: C Channel/Rod Calculation (New Function)
st.subheader("🛠 C Channel/Rod Calculation")

c_area = st.number_input("Enter Total Area to Cover (m²):", min_value=0.0, format="%.2f", key="c_area")
rod_length = st.number_input("Enter Length of One C Channel/Rod (meters):", min_value=0.1, format="%.2f", key="rod_length")
horizontal_spacing = st.number_input("Enter Horizontal Distance Between Rods (meters):", min_value=0.1, format="%.2f", key="h_spacing")
vertical_spacing = st.number_input("Enter Vertical Distance Between Rods (meters):", min_value=0.1, format="%.2f", key="v_spacing")

if st.button("Calculate Required C Channels/Rods"):
    rods_required = calculate_c_channels(c_area, rod_length, horizontal_spacing, vertical_spacing)
    if rods_required is not None:
        st.success(f"📌 You will need approximately `{rods_required:.2f}` C Channels/Rods.")
    else:
        st.error("Please enter valid values for the C Channel/Rod calculation.")

# Footer
st.markdown("---")
st.markdown("Developed with ❤️ using Streamlit.")