hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.13.2 Conformance requirement | VT(MS) - Maximum Send state variable.
This state variable contains the "Sequence Number" of the first AMD PDU that can be rejected by the peer Receiver, VT(MS) = VT(A) + VT(WS). This value represents the upper edge of the transmission window. The transmitter shall not transmit AMD PDUs with "Sequence Number"VT(MS) unle... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.13.3 Test purpose | To verify that the UE does not transmit PDUs with sequence numbers outside of the transmit window, except the PDU with SN=VT(S)-1, even when the transmit window size is changed by the receiver. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.13.4 Method of test | Initial conditions
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS 34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Access Bearer is replaced with the RAB defined for AM 7-bit "Length Indicator" tests in clause 7.2.3.1.
The fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.13.5 Test requirements | From steps 8 to 11, the SDU contents reassembled from the uplink shall match those of the first W transmitted SDUs.
At step 12 there shall be no further transmission on the uplink DTCH whilst the SS is waiting, except for any repeats of SDUs from 1 to W.
After step 13, the UE shall resume transmission of the next W SDU... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.14 Control of Receive Window | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.14.1 Definition | This test is to check that the UE is able to correctly control its RLC receive window. Correct operation of RLC windowing is critical for acknowledged mode operation.
This test applies to all UE. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.14.2 Conformance requirement | Upon reception of an AMD PDU with "Sequence Number" outside the interval VR(R)SN<VR(MR), the Receiver shall:
- discard the AMD PDU;
- if the "polling bit" in the discarded AMD PDU is set to "1":
- initiate the STATUS PDU transfer procedure.
Reference(s)
TS 25.322, clause 11.3.4.2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.14.3 Test purpose | To verify that the UE discards PDUs with sequence numbers outside the upper boundary of the receive window. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.14.4 Method of test | Initial conditions
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS 34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Access Bearer is replaced with the RAB defined for AM 7-bit "Length Indicator" tests in clause 7.2.3.1.
The fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.14.5 Test requirements | 1. The SS shall receive back SDUs 1 to W, and SDU W + 2 only. No other SDUs shall be looped back.
2. The SS shall receive a STATUS PDU in step 11a. SN=2W shall not be indicated as received in the STATUS PDU. Negative acknowledgements shall not be indicated for SN=W to 2W-1 either. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.15 Polling for status / Last PDU in transmission queue | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.15.1 Definition | This case tests that the UE will poll for a status request on the last PDU in its transmission queue when that mode is enabled. Incorrect operation of polling will cause degradation of service, or at worst service failure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.15.2 Conformance requirement | Last PDU in buffer.
When an AMD PDU to be transmitted for the first time is submitted to lower layer, the Sender shall:
- if the AMD PDU is the last AMD PDU scheduled for transmission according to subclause 11.3.2 (i.e. no data received from upper layer remains to be segmented into AMD PDUs); or
- if the AMD PDU is the... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.15.3 Test purpose | 1. To verify that a poll is performed when only one PDU is available for transmission, and the poll prohibit timer function is not used.
2. To verify that a poll is performed when only one PDU is available for transmission, and the poll prohibit timer function is used, but inactive. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.15.4 Method of test | Initial conditions
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS 34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Access Bearer is replaced with the RAB defined for AM 7-bit "Length Indicator" tests in clause 7.2.3.1.
The fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.15.5 Test requirements | The Poll bit shall be set in the AMD PDU header of the PDU returned in step 8. The poll bit shall not be set in the AMD PDU header of other PDUs. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.16 Polling for status / Last PDU in retransmission queue | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.16.1 Definition | This case tests that the UE will poll for a status request on the last PDU in its retransmission queue when that mode is enabled. Incorrect operation of polling will cause degradation of service, or at worst service failure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.16.2 Conformance requirement | Last PDU in Retransmission buffer.
When a retransmitted AMD PDU is submitted to lower layer, the Sender shall:
- if the AMD PDU is the last AMD PDU scheduled for retransmission according to subclause 11.3.2; or
- if the AMD PDU is the last of the AMD PDUs scheduled for retransmission that are allowed to transmit accord... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.16.3 Test purpose | 1. To verify that a poll is performed when only one PDU is available for retransmission, and the poll prohibit timer function is not used.
2. To verify that a poll is performed when only one PDU is available for retransmission, and the poll prohibit timer function is used, but inactive. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.16.4 Method of test | Initial conditions
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS 34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Access Bearer is replaced with the RAB defined for AM 7-bit "Length Indicator" tests in clause 7.2.3.1.
The fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.16.5 Test requirements | The Poll bit shall be set in the AMD PDU header of the PDU returned in step 11. The poll bit shall not be set in the AMD PDU header of other PDUs. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.17 Polling for status / Poll every Poll_PDU PDUs | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.17.1 Definition | This case tests that the UE will poll for a status request every Poll_PDU PDUs when that mode is enabled. Incorrect operation of polling will cause degradation of service, or at worst service failure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.17.2 Conformance requirement | VT(PDU).
This state variable is used when the "poll every Poll_PDU PDU" polling trigger is configured. It shall be incremented by 1 for each AMD PDU that is transmitted including both new and retransmitted AMD PDUs. When it becomes equal to the value Poll_PDU, a new poll shall be transmitted and the state variable shal... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.17.3 Test purpose | 1. To verify that a poll is performed when VT(PDU) reaches Poll_PDU.
2. To verify VT(PDU) is incremented for both new and retransmitted PDUs. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.17.4 Method of test | Initial conditions
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS 34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Access Bearer is replaced with the RAB defined for AM 7-bit "Length Indicator" tests in clause 7.2.3.1.
The fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.17.5 Test requirements | The SS shall receive a poll for status every Poll_PDU RLC PDUs sent on the uplink. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.18 Polling for status / Poll every Poll_SDU SDUs | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.18.1 Definition | This case tests that the UE will poll for a status request every Poll_SDU SDUs when that mode is enabled. Incorrect operation of polling will cause degradation of service, or at worst service failure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.18.2 Conformance requirement | VT(SDU).
This state variable is used when the "poll every Poll_SDU SDU" polling trigger is configured. It shall be incremented by 1 for a given SDU when the AMD PDUs carrying the first segment of this SDU is scheduled to be transmitted for the first time. When it becomes equal to the value Poll_SDU a new poll shall be ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.18.3 Test purpose | 1. To verify that a poll is performed when VT(SDU) reaches Poll_ SDU.
2. To verify that the poll is sent in the last PDU of the SDU. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.18.4 Method of test | Initial conditions
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Access Bearer is replaced with the RAB defined for AM 7-bit "Length Indicator" tests in clause 7.2.3.1.
The fol... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.18.5 Test requirements | The UE shall return uplink PDUs that contain polls for status in sequence numbers 2 * P – 1 and 4 * P – 1. No other PDUs shall poll for status. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.19 Polling for status / Timer triggered polling (Timer_Poll_Periodic) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.19.1 Definition | This case tests that the UE will poll for a status request every Timer_Poll_Periodic ms when that mode is enabled. Incorrect operation of polling will cause degradation of service, or at worst service failure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.19.2 Conformance requirement | This timer shall only be used when "timer based polling" is configured by upper layers. The value of the timer is signalled by upper layers. The timer shall be started when the RLC entity is created. When the timer expires, the RLC entity shall:
- restart the timer;
- if AMD PDUs are available for transmission or retra... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.19.3 Test purpose | 1. To verify that the UE polls the SS in the next PDU to be transmitted or retransmitted each time the Timer_Poll_Periodic timer expires.
2. To verify that if there is no PDU to be transmitted or retransmitted, the timer is restarted, but no poll is sent. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.19.4 Method of test | Initial conditions
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS 34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Access Bearer is replaced with the RAB defined for AM 7-bit "Length Indicator" tests in clause 7.2.3.1.
The fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.19.5 Test requirements | 1. No PDUs shall be received from the UE for 2*T ms before step 1.
2. Time T2 – T1 shall be T.
3. No PDUs shall be received from the UE for 2*T ms after step 9. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.20 Polling for status / Polling on Poll_Window% of transmission window | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.20.1 Definition | This case tests that the UE will poll for a status request when it has reached Poll_Window% of the transmission window, when that mode is enabled. Incorrect operation of polling will cause degradation of service, or at worst service failure.
This test applies to all UE. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.20.2 Conformance requirement | 1. A poll is triggered for each AMD PDU when JPoll_Window, where J is the window transmission percentage defined by
where the constant 4096 is the modulus for AM described in 3GPP TS 25.322 subclause 9.4 and VT(S) is the value of the variable before the AMD PDU is submitted to lower layer.
2. The Polling function is us... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.20.3 Test purpose | To verify that the UE polls the SS when the window based polling condition J >= Poll_Window is fulfilled. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.20.4 Method of test | Initial conditions
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS 34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Access Bearer is replaced with the RAB defined for AM 7-bit "Length Indicator" tests in clause 7.2.3.1.
The fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.20.5 Test requirements | The SS shall receive RLC PDUs with the P bit set in PDUs with sequence numbers of 3, 4, 5, 6 and 8. No other PDUs shall have their P bits set. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.21 Polling for status / Operation of Timer_Poll timer / Timer expiry | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.21.1 Definition | This case tests that the UE will retransmit a poll for status if it does not receive a STATUS PDU within Timer_Poll ms after a poll for status is transmitted. Incorrect operation of polling will cause degradation of service, or possible service failure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.21.2 Conformance requirement | Timer_Poll.
This timer shall only be used when so configured by upper layers. The value of the timer is signalled by upper layers. In the UE this timer shall be started when the successful or unsuccessful transmission of an AMD PDU containing a poll is indicated by lower layer. In UTRAN it should be started when an AMD... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.21.3 Test purpose | To verify that if the timer expires and no STATUS PDU containing an acknowledgement or negative acknowledgement of the AMD PDUs up to that which triggered the timer has been received, the receiver is polled once more. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.21.4 Method of test | Initial conditions
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS 34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Access Bearer is replaced with the RAB defined for AM 7-bit "Length Indicator" tests in clause 7.2.3.1.
The fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.21.5 Test requirements | For the first run, the measured time T2 – T1 shall be 600 ms.
For the second run, the measured time T2 – T1 shall be 1000 ms. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.22 Polling for status / Operation of Timer_Poll timer / Stopping Timer_Poll timer | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.22.1 Definition | This case tests that the UE will stop the Timer_Poll timer if it receives a STATUS PDU within Timer_Poll ms after a poll for status is transmitted. Incorrect operation of polling will cause degradation of service, or possible service failure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.22.2 Conformance requirement | Timer_Poll.
This timer shall only be used when so configured by upper layers. The value of the timer is signalled by upper layers. In the UE this timer shall be started when the successful or unsuccessful transmission of an AMD PDU containing a poll is indicated by lower layer. In UTRAN it should be started when an AMD... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.22.3 Test purpose | To verify that the Timer_Poll timer is stopped when receiving a STATUS PDU that acknowledges all AMD PDUs with SN up to and including VT(S)-1 at the time the poll was transmitted. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.22.4 Method of test | Initial conditions
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS 34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Access Bearer is replaced with the RAB defined for AM 7-bit "Length Indicator" tests in clause 7.2.3.1.
The fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.22.5 Test requirements | For both execution runs, the measured time T2 – T1 shall be 2000 ms. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.23 Polling for status / Operation of Timer_Poll timer / Restart of the Timer_Poll timer | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.23.1 Definition | This case tests that the UE will restart the Timer_Poll timer if another poll request is transmitted whilst the timer is running. Incorrect operation of polling will cause degradation of service, or possible service failure.
This test applies to all UE. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.23.2 Conformance requirement | Timer_Poll.
This timer shall only be used when so configured by upper layers. The value of the timer is signalled by upper layers. In the UE this timer shall be started when the successful or unsuccessful transmission of an AMD PDU containing a poll is indicated by lower layer. In UTRAN it should be started when an AMD... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.23.3 Test purpose | To verify that if a new poll is sent when the timer is running it is restarted. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.23.4 Method of test | Initial conditions
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS 34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Access Bearer is replaced with the RAB defined for AM 7-bit "Length Indicator" tests in clause 7.2.3.1.
The fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.23.5 Test requirements | The measured time T2 – T1 shall be 600 ms. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.24 Polling for status / Operation of timer Timer_Poll_Prohibit | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.24.1 Definition | This case tests that the UE will not send a poll request within Timer_Poll_Prohibit ms of a previous poll request when this mode of operation is enabled. Incorrect operation of polling will cause degradation of service, or possible service failure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.24.2 Conformance requirement | The timers defined in this subclause are normative. The timers shall be considered active from the time they are started until the time they either expire or are stopped.
b) Timer_Poll_Prohibit.
This timer shall only be used when so configured by upper layers. It is used to prohibit transmission of polls within a certa... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.24.3 Test purpose | 1. To verify that no poll is transmitted if one or several polls are triggered when the Timer_Poll_Prohibit timer is active and has not expired.
2. To verify that the UE polls only once after Timer_Poll_Prohibit expires even though triggered several times during the prohibit time. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.24.4 Method of test | Initial conditions
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS 34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Access Bearer is replaced with the RAB defined for AM 7-bit "Length Indicator" tests in clause 7.2.3.1.
The fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.24.5 Test requirements | 1. The measured time T2 – T1 shall be Timer_poll_prohibit ms.
2. After step 12 no further poll shall be received from the UE for the next Timer_poll_prohibit ms. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.25 Receiver Status Triggers / Detection of missing PDUs | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.25.1 Definition | This case tests that the UE transmits a status report whenever it detects that a PDU is missing, if this mode of operation is enabled. Incorrect operation of status reporting will cause degradation of service, or possible service failure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.25.2 Conformance requirement | Detection of missing PDU(s).
If the Receiver detects one or several missing AMD PDUs it shall trigger the transmission of a status report to the Sender.
Reference
TS 25.322 clause 9.7.2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.25.3 Test purpose | To verify that a status report is transmitted if there are one or more missing PDUs. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.25.4 Method of test | Initial conditions
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS 34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Access Bearer is replaced with the RAB defined for AM 7-bit "Length Indicator" tests in clause 7.2.3.1.
These ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.25.5 Test requirements | A STATUS PDU shall be received from the UE after step 4, indicating that the PDU with sequence number 7 was missing.
A STATUS PDU shall be received from the UE after step 9, indicating that the PDUs with sequence numbers 7, 13 and 14 were missing. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.26 Receiver Status Triggers / Operation of timer Timer_Status_Periodic | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.26.1 Definition | This case tests that the UE transmits a status report every Timer_Status_Periodic ms when this mode of operation is enabled. Incorrect operation of status reporting will cause degradation of service, or possible service failure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.26.2 Conformance requirement | This timer shall only be used when timer based status reporting is configured by upper layers.
This timer shall be started when the RLC entity is created. When the timer expires the transmission of a status report shall be triggered and the timer shall be restarted.
Reference
TS 25.322 clauses 9.5, 9.7.2 and 11.5.2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.26.3 Test purpose | To verify that a status report is transmitted each time the Timer_Status_Periodic timer expires. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.26.4 Method of test | Initial conditions
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS 34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Access Bearer is replaced with the RAB defined for AM 7-bit "Length Indicator" tests in clause 7.2.3.1.
The fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.26.5 Test requirements | The measured time T2 – T1 shall be 400 ms. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.27 Receiver Status Triggers / Operation of timer Timer_Status_Prohibit | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.27.1 Definition | This case tests that the UE does not transmit a status report more often than every Timer_Status_Prohibit ms when this mode of operation is enabled. Incorrect operation of status reporting will cause degradation of service, or possible service failure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.27.2 Conformance requirement | In the UE, this timer shall be started when the successful or unsuccessful transmission of the last STATUS PDU of an acknowledgement status report is indicated by lower layer
[...]
When a status report is triggered the Receiver shall:
- if transmission of status reports is not prohibited by any of the functions "STATUS... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.27.3 Test purpose | 1. To verify that a status report is not transmitted while the Timer_Status_Prohibit timer is active.
2. To verify that only one status report is sent on the expiry of the Timer_Status_Prohibit timer if several triggers occur while it is active. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.27.4 Method of test | Initial conditions
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS 34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Access Bearer is replaced with the RAB defined for AM 7-bit "Length Indicator" tests in clause 7.2.3.1.
The fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.27.5 Test requirements | 1. The measured time T2 – T1 shall be 500 ms.
2. Only one STATUS PDU shall be received in step 8 after (T1 + Tpro) and before (T1 + 2*Tpro). |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.28 Status reporting / Abnormal conditions / Reception of LIST SUFI with Length set to zero | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.28.1 Definition | Peer RLCs use STATUS PDUs to manage flow control and retransmission. On a STATUS report PDU with an invalid LIST SUFI the RLC must behave as specified. Incorrect behaviour may result in degradation of QoS, or failure of the UE to communicate. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.28.2 Conformance requirement | The List super-field
The List Super-Field consists of a type identifier field (LIST), a list length field (LENGTH) and a list of LENGTH number of pairs as shown in figure 9.11 below:
Type = LIST
LENGTH
SN1
L1
SN2
L2
…
SNLENGTH
LLENGTH
Figure 9.11: The List fields in a STATUS PDU
LENGTH
Length: 4 bits
The number of (SNi... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.28.3 Test purpose | To verify that if a STATUS PDU is received with a LIST SUFI and the LENGTH field is set to "0000" that the list is discarded. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.28.4 Method of test | Initial conditions
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS 34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Access Bearer is replaced with the RAB defined for AM 7-bit "Length Indicator" tests in clause 7.2.3.1.
The fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.28.5 Test requirements | No RLC PDUs shall be retransmitted by the UE. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.29 Timer based discard, with explicit signalling / Expiry of Timer_Discard | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.29.1 Definition | This case tests that when the transmission of an SDU exceeds a time limit, the SDU is discarded by the sender, and the discard is signalled to the receiver. SDU discard is used to keep network delays within limits, and incorrect operation will effect the quality of service. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.29.2 Conformance requirement | If the transmission time exceeds a predefined value for a SDU in acknowledged mode RLC, this SDU is discarded in the transmitter and a Move Receiving Window (MRW) command is sent to the receiver so that AMD PDUs carrying that SDU are discarded in the receiver and the receiver window is updated accordingly.
This procedu... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.29.3 Test purpose | 1. To verify that if the transmission time for an SDU exceeds Timer_Discard, the SDU is discarded in the transmitter and the MRW procedure is invoked.
2. ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.29.4 Method of test | Initial conditions
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS 34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Access Bearer is replaced with the RAB defined for AM 7-bit "Length Indicator" tests in clause 7.2.3.1.
The fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.2.3.29.5 Test requirements | 1. The measured time T2 – T1 shall be 1000 ms.
2. The STATUS PDU received in step 9 shall contain a MRW SUFI indicating that the first three PDUs shall be discarded, and that the data indicated in the fourth PDU by the first LI shall also be discarded.
7.2.3.29a Timer based discard, with explicit signalling / Expiry of... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.