hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.7.10.1.4 Test requirements | See 14.1.3.5 for definition of the referenced step numbers.
1. At step 12 the UE shall send RADIO BEARER SETUP COMPLETE.
2. At steps 17 to 20 the UE transmitted transport format shall be within the set of restricted TFCIs as specified for the actual sub-test.
3. At step 18 and for each TFRC test point:
If the downlink ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.7.10.2 Streaming / unknown / UL:128 DL: [guaranteed 128, max bit rate depending on UE category] kbps / PS RAB + Interactive or background / UL:128 DL: [max bit rate depending on UE category] / PS RAB, UL 144bit block size | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.7.10.2.1 Conformance requirement | See 18.2.7.1.1.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.7.10.2.2 Test purpose | To verify radio bearer establishment and correct data transfer for reference radio bearer configuration as specified in TS 34.108, clause 6.10.3.4.6.10 for the UL 144 bit block size case. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.7.10.2.3 Method of test | The generic test procedure in 14.1.3.5 is run for each sub-test.
Uplink TFS:
TFI
RB5
(Streaming
128 kbps, 20ms)
RB6
(I/B
128 kbps, 20ms)
DCCH
TFS
TF0, bits
0x656
0x144
0x148
TF1, bits
1x656
1x144
1x148
TF2, bits
2x656
7x144
N/A
TF3, bits
4x656
14x144
N/A
TF4, bits
N/A
20x144
N/A
Uplink TFCS:
TFCI
(RB5 + RB6, DCCH)
UL_T... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.7.10.2.4 Test requirements | See 14.1.3.5 for definition of the referenced step numbers.
1. At step 12 the UE shall send RADIO BEARER SETUP COMPLETE.
2. At steps 17 to 20 the UE transmitted transport format shall be within the set of restricted TFCIs as specified for the actual sub-test.
3. At step 18 and for each TFRC test point:
If the downlink ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8 Combinations on DPCH, HS-DSCH and E-PUCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.1 Streaming or interactive or background / UL: [max bit rate depending on UE category and TTI] DL: [max bit rate depending on UE category] / PS RAB + UL:3.4 DL:3.4 kbps SRBs for DCCH on DCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.1.1 Conformance requirement | The UE shall be able to establish the UTRAN requested radio bearers within the UE's signalled radio access capabilities.
The UE shall correctly transfer user data from peer to peer RLC entities according to the requested radio bearer configuration.
Reference(s)
3GPP TS 25.331, clause 8.2.1
3GPP TS 25.2xx series (Physic... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.1.2 Test purpose | For the reference radio bearer configuration as specified in TS 34.108, clause 6.10.3.4.7.1:
1. To verify that the UE is able to establish the radio bearer combination.
2. To verify correct data transfer using all the possible MAC-d PDU sizes of the transport channel mapped to E-DCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.1.3 Method of test | The following parameters are specific for this test case:
Parameter
Value
MAC-hs receiver window size
16
HS-DSCH MAC-d PDU size
336
E-DCH
Category
RLC Transmission window size
1
512
2
512
3
512
4
1536
5
1536
HS-DSCH Category
HS-PDSCH
Number of HARQ processes
RLC Receiving window size
HS-PDSCH TFRC
(note 1)
Max MAC-d PD... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.1.4 Test requirements | See 18.2.1.5 for definition of step 12 and step 18.
1. At step 12 the UE shall send RADIO BEARER SETUP COMPLETE.
2. At step 18 the UE shall return a RLC SDU with same content as sent in downlink. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.2 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.3 Streaming or interactive or background / UL: [max bit rate depending on UE category and TTI] DL: [max bit rate depending on UE category] / PS RAB + UL: [max bit rate depending on UE category and TTI] DL: [max bit rate depending on UE category] SRBs for DCCH on E-DCH and HS-DSCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.3.1 Conformance requirement | See 18.2.8.1.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.3.2 Test purpose | For the reference radio bearer configuration as specified in TS 34.108, clause 6.10.3.4.7.3:
1. To verify that the UE is able to establish the radio bearer combination.
2 To verify correct data transfer using all the possible MAC-d PDU sizes of the transport channel mapped to E-DCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.3.3 Method of test | See 18.2.8.1.3. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.3.4 Test requirements | See 18.2.8.1.4. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.4 Conversational / speech / UL:12.2 DL:12.2 kbps / CS RAB + Streaming or interactive or background / UL: [max bit rate depending on UE category and TTI] DL: [max bit rate depending on UE category] / PS RAB + UL:3.4 DL:3.4 kbps SRBs for DCCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.4.1 Conformance requirement | See 18.2.8.1.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.4.2 Test purpose | For the reference radio bearer configuration as specified in TS 34.108, clause 6.10.3.4.7.4:
1. To verify that the UE is able to establish the radio bearer combination.
2 To verify correct data transfer using all the possible MAC-d PDU sizes of the transport channel mapped to E-DCH in combination with the possible TFCI... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.4.3 Method of test | The following parameters are specific for this test case:
Uplink TFS:
RB5
(RAB subflow #1)
RB6
(RAB subflow #2)
RB7
(RAB subflow #3)
DCCH
TFS
TF0, bits
1x0
0x103
0x60
0x148
TF1, bits
1x39
1x103
1x60
1x148
TF2, bits
1x81
N/A
N/A
N/A
Uplink TFCS:
TFCI
(RB5, RB6, RB7, DCCH)
UL_TFC0
(TF0, TF0, TF0, TF0)
UL_TFC1
(TF1, TF0, ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.4.4 Test requirements | See 18.2.1.5 for definition of step 12 and step 18.
1. At step 12 the UE shall send RADIO BEARER SETUP COMPLETE.
2. At steps 17 to 20 the UE transmitted transport format shall be within the set of restricted TFCIs as specified for the sub-test.
3. At step 18 and for each radio bearer where test data is sent in downlink... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.5 Streaming or interactive or background / UL:[max bit rate depending on UE category and TTI] DL: [max bit rate depending on UE category] kbps / PS RAB + Streaming or interactive or background / UL: [max bit rate depending on UE category and TTI] DL: [max bit rate depending on UE category] / PS RAB + UL:[max bit... | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.5.1 Conformance requirement | See 18.2.8.1.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.5.2 Test purpose | For the reference radio bearer configuration as specified in TS 34.108, clause 6.10.3.4.7.5:
1. To verify that the UE is able to establish the radio bearer combination.
2 To verify correct data transfer using all the possible MAC-d PDU sizes of the transport channel mapped to E-DCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.5.3 Method of test | The first Streaming or background or interactive / UL:[max bit rate depending on UE category and TTI] DL: [max bit rate depending on UE category] kbps / PS RAB is referred to as RB5 and the second Streaming or interactive or background UL:[max bit rate depending on UE category and TTI] DL: [max bit rate depending on UE... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.2.8.5.4 Test requirements | See 18.2.1.5 for definition of step 12 and step 18.
1. At step 12 the UE shall send RADIO BEARER SETUP COMPLETE.
2. At step 18 the UE shall return a RLC SDU on RB5 and RB6 with same content as sent in downlink.
18.3 Radio Bearer Tests for 7.68 Mcps TDD option |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1 General information for radio bearer tests (7.68 Mcps TDD) | The purpose of these radio bearer test cases is to test properly the Reference Radio Bearer configurations included in TS34.108 [9], clause 6.11.6 for 7.68 Mcps TDD option.
The applicability of radio bearer tests is dependent on the UE uplink and downlink radio access capabilities and UE support tele- and bearer-servic... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.1 Generic radio bearer test procedure for Single RB configuration | See 14.1.1 for test procedure |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.2 Generic test procedure for testing multi-RB configuration and simultaneous signalling | See 14.1.2 for test procedure
18.3.1.2a Generic test procedure for testing multi-RB combinations and simultaneous signalling in case of DSCH
This procedure is used to test multiple radio bearer combinations where PS data goes on the DSCH. This procedure is also used to verify simultaneous transmission and reception of ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.3 Generic test procedure for testing Single Speech Radio Bearers on USCH/DSCH channels and multiple radio configuration signalling on RACH/FACH | This procedure is used to test single speech only PS radio bearer on DSCH and USCH and multiple configuration signal bearers on RACH/FACH |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.3.1 Initial conditions | UE in idle mode |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.3.2 Test procedure | a) The SS establish the reference radio bearer configuration as specified in TS 34.108, clause 6.10 for the actual radio bearer test.
b) The SS limits the UE allowed uplink transport format combinations according to the "Restricted UL TFCIs", as specified for the sub-test of the actual radio bearer test, using the RRC ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.4 General information interoperability radio bearer tests for HS-DSCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.4.1 HS-DSCH radio bearer test parameters | In the radio bearer tests on radio bearers mapped on HS-DSCH, the following UE specific parameters should be used.
Table 18.3.1.4.1.1: 7.68Mcps TDD HS-DSCH physical layer and RLC and MAC-hs parameters for 7.68Mcps TDD HS-DSCH physical layer categories
HS-DSCH category
Maximum number of HS-DSCH codes per timeslot
Maximu... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.4.2 Selecting TFRC test points | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.4.2.1 Principle | The principle for selecting TFRC test points is the same as specified for FDD in section 14.1.3.2.1 except the following:
a) A total of 3 HARQ processes are assumed.
b) Burst type 1 is assumed when calculating the number of physical channel bits (Nphy_bits) so that 1 HS-DSCH code in 1 TS carries 244bits for QPSK and 48... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.4.3 TFRC test points for MAC-d PDU size=336 | Table 18.3.1.4.3.1: TFRC test points for UE category 1 for MAC-d PDU size=336, 7.68Mcps TDD
Number of MAC-d PDUs
Selected transport block size [bits]
Modulation scheme
Ncodes*NTS allocated in HS-SCCH
TFRI
Comments
1
357
QPSK
4
115
1
357
16 QAM
2
115
2
693
QPSK
8
156
2
693
16 QAM
4
156
3
1029
QPSK
12
181
3
1029
16 QAM
... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.4.4 TFRC test points for MAC-d PDU size=656 | Table 18.3.1.4.4.1: TFRC test points for UE category 1 for MAC-d PDU size=656, 7.68Mcps TDD
Number of MAC-d PDUs
Selected transport block size [bits]
Modulation scheme
Number of resource units
TFRI
Comments
1
677
QPSK
8
155
1
677
16 QAM
4
155
2
1333
QPSK
16
197
2
1333
16 QAM
8
197
3
1989
QPSK
24
222
3
1989
16 QAM
12
2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.5 Generic test procedure radio bearers on MTCH | See 14.1.5 for test procedure |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.6 Generic test procedure for radio bearers on MBSFN MTCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.6.1 Initial conditions | System Simulator:
- 1 MBMS MBSFN Cell 31 with default parameters.
In addition to broadcasting System Information, MCCH messages are transmitted by the SS using MBMS configuration C1 and Default1 MCCH scheduling (No ongoing service). See subclause 11.1 of TS 34.108.
- 1 unicast carrier Cell 1 with default parameters.
Us... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.6.2 Test procedure | a) The SS sends CLOSE UE TEST LOOP via the unicast carrier cell, requesting activation of Test Loop Mode 3 specifying the MBSFN MBMS short transmission identity of the MTCH for the activated service
b) The SS notifies on MCCH about the start of an MBMS session and waits for the UE to activate MTCH reception at the spec... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.7 General information for interoperability radio bearer tests for E-DCH and HS-DSCH combinations | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.7.1 Generic test procedure for HS-DSCH and E-DCH radio bearer combinations | This procedure is used to test E-DCH radio bearer combinations. The procedure is run once for each sub-test of the actual E-DCH radio bearer test case.
Definition of test variables:
NTS
The number of HS-DSCH timeslots as specified by the sub-test. This parameter is dependent on the UE capability.
Ncodes
The number of ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.7.1.1 Initial conditions | UE in idle mode |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.1.7.1.2 Test procedure | a) The SS establish the reference radio bearer configuration as specified in TS 34.108, clause 6.11 for the actual radio bearer test. For the case when the reference radio bearer configuration includes radio bearers for both CS and PS domain then the radio bearer setup procedure has to be performed once per domain. The... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2 Combinations on DPCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.1 Stand-alone UL:1.7 DL:1.7 kbps SRBs for DCCH | Test to verify establishment and signalling of stand-alone signalling reference radio bearer configuration as specified in TS 34.108, clause 6.11.6.4.1.1.
The test case is performed by running test case 9.4.1 (Location updating / accepted) using the stand-alone signalling reference radio bearer configuration as specifi... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.2 Stand-alone UL:3.4 DL:3.4 kbps SRBs for DCCH | Test to verify establishment and signalling of stand-alone signalling reference radio bearer configuration as specified in TS 34.108, clause 6.11.6.4.1.2.
The test case is performed by running test case 9.4.1 (Location updating / accepted) using the stand-alone signalling reference radio bearer configuration as specifi... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.3 Stand-alone UL:13.6 DL:13.6 kbps SRBs for DCCH | Implicitly tested.
NOTE The stand-alone UL:13.6 DL:13.6 kbps SRBs for DCCH in TS 34.108, clause 6.11.6.4.1.3 is the default signalling radio bearer used in the generic setup procedure as specified in TS 34.108 clause 7. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.4 Conversational / speech / UL:12.2 DL:12.2 kbps / CS RAB + UL:3.4 DL:3.4 kbps SRBs for DCCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.4.1 Conformance requirement | The UE shall be able to establish the UTRAN requested radio bearers within the UE's signalled radio access capabilities.
The UE shall correctly transfer user data from peer to peer RLC entities according to the requested radio bearer configuration.
Reference(s)
3GPP TS 25.331, clause 8.2.1
3GPP TS 25.2xx series (Physic... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.4.2 Test purpose | To verify radio bearer establishment and correct data transfer for reference radio bearer configuration as specified in TS 34.108, clause 6.11.6.4.1.4. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.4.3 Method of test | Uplink TFS:
TFI
RB5
(RAB subflow #1)
RB6
(RAB subflow #2)
RB7
(RAB subflow #3)
DCCH
TFS
TF0, bits
0x81(alt. 1x0)
0x103
0x60
0x148
TF1, bits
1x39
1x103
1x60
1x148
TF2, bits
1x81
N/A
N/A
N/A
Uplink TFCS:
TFCI
(RB5, RB6, RB7, DCCH)
UL_TFC0
(TF0, TF0, TF0, TF0)
UL_TFC1
(TF1, TF0, TF0, TF0)
UL_TFC2
(TF2, TF1, TF1, TF0)
UL_T... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.4.4 Test requirements | See 18.3.1.1 for definition of step 10 and step 15.
1. At step 10 the UE shall send RADIO BEARER SETUP COMPLETE.
2. At step 15 the UE transmitted transport format shall be
- for sub-test 1: RB5/TF1 (1x39).
- for sub-test 2: RB5/TF2 (1x81); RB6/TF1 (1x103); and RB7/TF1 (1x60).
3. At step 15 the UE shall return
- for sub... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.5 Conversational / speech / UL:10.2 DL:10.2 kbps / CS RAB + UL:3.4 DL: 3.4 kbps SRBs for DCCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.5.1 Conformance requirement | See clause 18.3.2.4.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.5.2 Test purpose | To verify radio bearer establishment and correct data transfer for reference radio bearer configuration as specified in TS 34.108, clause 6.11.6.4.1.5. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.5.3 Method of test | Uplink TFS:
TFI
RB5
(RAB subflow #1)
RB6
(RAB subflow #2)
RB7
(RAB subflow #3)
DCCH
TFS
TF0, bits
0x65(alt. 1x0)
0x99
0x40
0x148
TF1, bits
1x39
1x99
1x40
1x148
TF2, bits
1x65
N/A
N/A
N/A
Uplink TFCS:
TFCI
(RB5, RB6, RB7,DCCH)
UL_TFC0
(TF0, TF0, TF0, TF0)
UL_TFC1
(TF1, TF0, TF0, TF0)
UL_TFC2
(TF2, TF1, TF1, TF0)
UL_TFC3... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.5.4 Test requirements | See 18.3.1.1 for definition of step 10 and step 15.
1. At step 10 the UE shall send RADIO BEARER SETUP COMPLETE.
2. At step 15 the UE transmitted transport format shall be
- for sub-test 1: RB5/TF1 (1x39).
- for sub-test 2: RB5/TF2 (1x65); RB6/TF1 (1x99); and RB7/TF1 (1x40).
3. At step 15 the UE shall return
- for sub-... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.6 Conversational / speech / UL:7.95 DL:7.95 kbps / CS RAB + UL:3.4 DL:3.4 kbps SRBs for DCCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.6.1 Conformance requirement | See clause 18.3.2.4.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.6.2 Test purpose | To verify radio bearer establishment and correct data transfer for reference radio bearer configuration as specified in TS 34.108, clause 6.11.6.4.1.6. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.6.3 Method of test | Uplink TFS:
TFI
RB5
(RAB subflow #1)
RB6
(RAB subflow #2)
DCCH
TFS
TF0, bits
0x75(alt. 1x0)
0x84
0x148
TF1, bits
1x39
1x84
1x148
TF2, bits
1x75
N/A
N/A
Uplink TFCS:
TFCI
(RB5, RB6, DCCH)
UL_TFC0
(TF0, TF0, TF0)
UL_TFC1
(TF1, TF0, TF0)
UL_TFC2
(TF2, TF1, TF0)
UL_TFC3
(TF0, TF0, TF1)
UL_TFC4
(TF1, TF0, TF1)
UL_TFC5
(TF2,... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.6.4 Test requirements | See 18.3.1.1 for definition of step 10 and step 15.
1. At step 10 the UE shall send RADIO BEARER SETUP COMPLETE.
2. At step 15 the UE transmitted transport format shall be
- for sub-test 1: RB5/TF1 (1x39).
- for sub-test 2: RB5/TF2 (1x75) and RB6/TF1 (1x84).
3. At step 15 the UE shall return
- for sub-test 1: an RLC SD... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.7 Conversational / speech / UL:7.4 DL:7.4 kbps / CS RAB+ UL:3.4 DL:3.4 kbps SRBs for DCCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.7.1 Conformance requirement | See clause 18.3.2.4.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.7.2 Test purpose | To verify radio bearer establishment and correct data transfer for reference radio bearer configuration as specified in TS 34.108, clause 6.11.6.4.1.7. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.7.3 Method of test | Uplink TFS:
TFI
RB5
(RAB subflow #1)
RB6
(RAB subflow #2)
DCCH
TFS
TF0, bits
0x61 (alt. 1x0)
0x87
0x148
TF1, bits
1x39
1x87
1x148
TF2, bits
1x61
N/A
N/A
Uplink TFCS:
TFCI
(RB5, RB6, DCCH)
UL_TFC0
(TF0, TF0, TF0)
UL_TFC1
(TF1, TF0, TF0)
UL_TFC2
(TF2, TF1, TF0)
UL_TFC3
(TF0, TF0, TF1)
UL_TFC4
(TF1, TF0, TF1)
UL_TFC5
(TF2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.7.4 Test requirements | See 18.3.1.1 for definition of step 10 and step 15.
1. At step 10 the UE shall send RADIO BEARER SETUP COMPLETE.
2. At step 15 the UE transmitted transport format shall be
- for sub-test 1: RB5/TF1 (1x39).
- for sub-test 2: RB5/TF2 (1x61) and RB6/TF1 (1x87).
3. At step 15 the UE shall return
- for sub-test 1: an RLC SD... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.8 Conversational / speech / UL:6.7 DL:6.7 kbps / CS RAB + UL:3.4 DL:3.4 kbps SRBs for DCCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.8.1 Conformance requirement | See clause 18.3.2.4.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.8.2 Test purpose | To verify radio bearer establishment and correct data transfer for reference radio bearer configuration as specified in TS 34.108, clause 6.11.6.4.1.8. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.8.3 Method of test | Uplink TFS:
TFI
RB5
(RAB subflow #1)
RB6
(RAB subflow #2)
DCCH
TFS
TF0, bits
0x58(alt. 1x0)
0x76
0x148
TF1, bits
1x39
1x76
1x148
TF2, bits
1x58
N/A
N/A
Uplink TFCS:
TFCI
(RB5, RB6, DCCH)
UL_TFC0
(TF0, TF0, TF0)
UL_TFC1
(TF1, TF0, TF0)
UL_TFC2
(TF2, TF1, TF0)
UL_TFC3
(TF0, TF0, TF1)
UL_TFC4
(TF1, TF0, TF1)
UL_TFC5
(TF2,... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.8.4 Test requirements | See clause 18.3.1.1 for definition of step 10 and step 15.
1. At step 10 the UE shall send RADIO BEARER SETUP COMPLETE.
2. At step 15 the UE transmitted transport format shall be
- for sub-test 1: RB5/TF1 (1x39).
- for sub-test 2: RB5/TF2 (1x58) and RB6/TF1 (1x76).
3. At step 15 the UE shall return
- for sub-test 1: an... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.9 Conversational / speech / UL:5.9 DL:5.9 kbps / CS RAB + UL:3.4 DL:3.4 kbps SRBs for DCCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.9.1 Conformance requirement | See clause 18.3.2.4.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.9.2 Test purpose | To verify radio bearer establishment and correct data transfer for reference radio bearer configuration as specified in TS 34.108, clause 6.11.6.4.1.9. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.9.3 Method of test | Uplink TFS:
TFI
RB5
(RAB subflow #1)
RB6
(RAB subflow #2)
DCCH
TFS
TF0, bits
0x55(alt. 1x0)
0x63
0x148
TF1, bits
1x39
1x63
1x148
TF2, bits
1x55
N/A
N/A
Uplink TFCS:
TFCI
(RB5, RB6, DCCH)
UL_TFC0
(TF0, TF0, TF0)
UL_TFC1
(TF1, TF0, TF0)
UL_TFC2
(TF2, TF1, TF0)
UL_TFC3
(TF0, TF0, TF1)
UL_TFC4
(TF1, TF0, TF1)
UL_TFC5
(TF2,... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.9.4 Test requirements | See 18.3.1.1 for definition of step 10 and step 15.
1. At step 10 the UE shall send RADIO BEARER SETUP COMPLETE.
2. At step 15 the UE transmitted transport format shall be
- for sub-test 1: RB5/TF1 (1x39).
- for sub-test 2: RB5/TF2 (1x55) and RB6/TF1 (1x63).
3. At step 15 the UE shall return
- for sub-test 1: an RLC SD... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.10 Conversational / speech / UL:5.15 DL:5.15 kbps / CS RAB + UL:1.7 DL:1.7 kbps SRBs for DCCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.10.1 Conformance requirement | See clause 18.3.2.4.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.10.2 Test purpose | To verify radio bearer establishment and correct data transfer for reference radio bearer configuration as specified in TS 34.108, clause 6.11.6.4.1.10. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.10.3 Method of test | Uplink TFS:
TFI
RB5
(RAB subflow #1)
RB6
(RAB subflow #2)
DCCH
TFS
TF0, bits
0x49 (alt. 1x0)
0x54
0x148
TF1, bits
1x39
1x54
1x148
TF2, bits
1x49
N/A
N/A
Uplink TFCS:
TFCI
(RB5, RB6, DCCH)
UL_TFC0
(TF0, TF0, TF0)
UL_TFC1
(TF1, TF0, TF0)
UL_TFC2
(TF2, TF1, TF0)
UL_TFC3
(TF0, TF0, TF1)
UL_TFC4
(TF1, TF0, TF1)
UL_TFC5
(TF2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.10.4 Test requirements | See 18.3.1.1 for definition of step 10 and step 15.
1. At step 10 the UE shall send RADIO BEARER SETUP COMPLETE.
2. At step 15 the UE transmitted transport format shall be
- for sub-test 1: RB5/TF1 (1x39).
- for sub-test 2: RB5/TF2 (1x49) and RB6/TF1 (1x54).
3. At step 15 the UE shall return
- for sub-test 1: an RLC SD... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.11 Conversational / speech / UL:4.75 DL:4.75 kbps / CS RAB + UL:1.7 DL:1.7 kbps SRBs for DCCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.11.1 Conformance requirement | See clause 18.3.2.4.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.11.2 Test purpose | To verify radio bearer establishment and correct data transfer for reference radio bearer configuration as specified in TS 34.108, clause 6.11.6.4.1.11. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.11.3 Method of test | Uplink TFS:
TFI
RB5
(RAB subflow #1)
RB6
(RAB subflow #2)
DCCH
TFS
TF0, bits
0x49(alt.1x0 )
0x53
0x148
TF1, bits
1x39
1x53
1x148
TF2, bits
1x42
N/A
N/A
Uplink TFCS:
TFCI
(RB5, RB6, DCCH)
UL_TFC0
(TF0, TF0, TF0)
UL_TFC1
(TF1, TF0, TF0)
UL_TFC2
(TF2, TF1, TF0)
UL_TFC3
(TF0, TF0, TF1)
UL_TFC4
(TF1, TF0, TF1)
UL_TFC5
(TF2,... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.11.4 Test requirements | See clause 18.3.1.1 for definition of step 10 and step 15.
1. At step 10 the UE shall send RADIO BEARER SETUP COMPLETE.
2. At step 15 the UE transmitted transport format shall be
- for sub-test 1: RB5/TF1 (1x39).
- for sub-test 2: RB5/TF2 (1x42) and RB6/TF1 (1x53).
3. At step 15 the UE shall return
- for sub-test 1: an... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.12 Conversational / unknown / UL:28.8 DL:28.8 kbps / CS RAB + UL:3.4 DL:3.4 kbps SRBs for DCCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.12.1 Conformance requirement | See 18.3.2.4.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.12.2 Test purpose | To verify radio bearer establishment and correct data transfer for reference radio bearer configuration as specified in TS 34.108, clause 6.11.6.4.1.12. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.12.3 Method of test | Uplink RLC
TM RLC
Segmentation indication
FALSE
Downlink RLC
TM RLC
Segmentation indication
FALSE
Uplink TFS:
TFI
RB5
(28.8 kbps)
DCCH
TFS
TF0, bits
0x576
0x148
TF1, bits
1x576
1x148
Uplink TFCS:
TFCI
(RB5, DCCH)
UL_TFC0
(TF0, TF0)
UL_TFC1
(TF1, TF0)
UL_TFC2
(TF0, TF1)
UL_TFC3
(TF1, TF1)
Downlink TFS:
RB5
(28.8 kbps)
D... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.12.4 Test requirements | See clause 18.3.1.1 for definition of step 10 and step 15.
1. At step 10 the UE shall send RADIO BEARER SETUP COMPLETE.
2. At step 15 the UE transmitted transport format shall be
- for sub-test 1: RB5/TF1 (1x576).
3. At step 15 the UE shall return
- for sub-test 1: an RLC SDU on RB5 having the same content as sent by S... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.13 Conversational / unknown / UL:64 DL:64 kbps / CS RAB + UL:3.4 DL:3.4 kbps SRBs for DCCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.13.1 Conversational / unknown / UL:64 DL:64 kbps / CS RAB + UL:3.4 DL:3.4 kbps SRBs for DCCH / 20ms TTI | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 18.3.2.13.1.1 Conformance requirement | See clause 18.3.2.4.1. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.