hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.1.3 Test purpose | 1) To verify that an MS with human interface, in a SETUP message sent to originate a call, includes the same "Number digits" in the "Called party BCD number" of the SETUP message as displayed.
2) To verify that an MS with MMI, when made to establish a call sends a SETUP message, which includes the "Numbering plan ident... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.1.4.1 Initial conditions | The MS is registered in a cell of the SS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.1.4.2 Procedure | a) A number (not including "+ function") is entered and then a call is set up.
b) After the SS has accepted the call the number displayed on the MS and the number received in the SS are compared.
c) The NPI and TON are examined in the SS.
d) Steps a) to c) are repeated, but in a), the number entered starts with the "+ ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.1.5 Test requirements | 1) In step b), both numbers shall be identical.
2) In step c), the NPI shall be "E164" and the TON shall be "unknown".
3) In step d), the NPI shall be "E164" and the TON shall be "international". |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2 Indication of call progress signals | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.1 Definition | Void. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.2 Conformance requirement | Void. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.3 Test purpose | Void. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.4 Ringing tone | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.4.1 Method of test | a) According to subclause "Structured procedures, Mobile originating call, early assignment, Method of test", paragraphs a) to j). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.4.2 Requirements | 1) According to subclause "Structured procedures, Mobile originating call, early assignment, Requirements", paragraphs 1) to 7).
2) The ringing tone characteristics shall be as follows:
Tone
Frequency
Tolerance
Type
Ringing tone
425 Hz
15 Hz
Periodic
tone on 1 s,
silence 4 s |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.5 Busy tone | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.5.1 Method of test | a) According to subclause "Structured procedures, Mobile originating call, early assignment, Method of test", paragraphs a) to h).
b) The SS then sends message DISCONNECT with cause number 17.
Message: DISCONNECT (3GPP TS 04.08 / 3GPP TS 24.008, subclause 9.3.7) to the MS:
Information element
Comment
Protocol discrimin... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.5.2 Requirements | 1) According to subclause "Structured procedures, Mobile originating call, early assignment, Requirements", paragraphs 1) to 5).
2) After the reception of DISCONNECT a busy tone shall be generated. The busy tone characteristics shall be as follows:
Tone
Frequency
Tolerance
Type
Busy tone
425 Hz
15 Hz
Periodic
tone on 5... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.6 Congestion tone | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.6.1 Method of test | a) According to subclause "Structured procedures, Mobile originating call, early assignment, Method of test", paragraphs a) to h).
b) The SS then sends message DISCONNECT with cause number 42.
DISCONNECT message: As in subclause 33.2.3.1 with cause value #42 "Switching equipment congestion" (0101010). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.6.2 Requirements | 1) According to subclause "Structured procedures, Mobile originating call, early assignment, Requirements", paragraphs 1) to 5).
2) After the reception of DISCONNECT a congestion tone shall be generated.
3) The congestion tone characteristics shall be as follows:
Tone
Frequency
Tolerance
Type
Congestion tone
425 Hz
15 ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.7 Authentication failure tone | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.7.1 Method of test | a) According to subclause "Structured procedures, Mobile originating call, early assignment, Method of test", paragraphs a) to e).
b) After reception of message AUTHENTICATION RESPONSE the SS sends message AUTHENTICATION REJECT.
Message: AUTHENTICATION REJECT (3GPP TS 04.08 / 3GPP TS 24.008, 9.2.1) to the MS:
Informati... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.7.2 Requirements | 1) According to subclause "Structured procedures, Mobile originating call, early assignment, Requirements", paragraphs 1) to 4).
2) After reception of AUTHENTICATION REJECT a tone shall be generated indicating authentication failure.
3) The authentication failure tone is the error/special information tone with characte... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.8 Number unobtainable tone | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.8.1 Method of test | a) According to subclause "Structured procedures, Mobile originating call, early assignment, Method of test", paragraphs a) to h).
b) The SS then sends message DISCONNECT with cause number 1.
DISCONNECT message: As in subclause 33.2.3.1 with cause value #1 "Unassigned (unallocated) number" (0000001). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.8.2 Requirements | 1) According to subclause "Structured procedures, Mobile originating call, early assignment, Requirements", paragraphs 1) to 5).
2) After reception of DISCONNECT a tone shall be generated indicating that the called number is unobtainable.
The number unobtainable tone is the error/special information tone with character... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.9 Call dropped tone | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.9.1 Method of test | a) According to subclause "Structured procedures, Mobile originating call, early assignment, Method of test", paragraphs a) to l). However, it shall be indicated in the system information messages that call re-establishment shall not be attempted (RACH control parameters).
b) When the call has been established the SS s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.2.9.2 Requirements | 1) According to subclause "Structured procedures, Mobile originating call, early assignment, Requirements", paragraphs 1) to 8).
2) After the radio link time-out period has expired a tone shall be generated indicating that the call has been dropped.
The call dropped tone characteristics shall be as follows:
Tone
Freque... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.3 Network selection / indication | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.3.1 Definition | Network selection and indication is the ability of the MS to correctly select a network and display to the user in accordance with 3GPP TS 02.11 and 3GPP TS 03.22.
Tests concerning the MS behaviour after having received a location updating reject message with specific causes are included in subclause 26.7.4.2.
Tests co... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.3.2 Conformance requirement | 1) Upon switching on, when an IMSI is available and there is no registered PLMN on the SIM, the MS shall select its Home PLMN and perform the cell selection procedure.
2) If the MS loses radio coverage for its registered PLMN, and the MS is in automatic PLMN selection mode, it shall attempt to select its Home PLMN.
3) ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.3.3 Test purpose | 1) To verify that the MS with SIM containing in the PLMN selector field at least one PLMN different from the Home PLMN and containing no registered PLMN, when in automatic PLMN selection mode, selects its Home PLMN, if available, upon switching on and when the IMSI is available. (This is verified by observation of the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.3.4 Method of Test | Procedure 1: This procedure applies to both automatic and manual mode for PLMN selection. This procedure is run for each of the following cases:
case A) Timer T is set to 6 min in the SIM.
case B) No HPLMN search timer value is available on the SIM.
case C) Timer T is set to "no periodic attempt to obtain service on th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.3.4.1 Procedure 1 | 1.1) The MS is set up with a SIM which contains, in the "PLMN selector" data field, a list of 3 PLMN in the priority order PLMN2 (highest priority), PLMN3, PLMN4 (lowest priority). PLMN1 is the Home PLMN of the MS as defined in the IMSI. The "Forbidden PLMN" data field shall contain NULL values. "registered PLMN" data ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.3.4.2 Requirements 1 | Requirement 1.1) is mandatory for all MS. Requirements 1.2) only apply to MS capable of indicating PLMN.
1.1) The MS shall make a response as indicated in steps 1.4, 1.7, 1.10, 1.13A, 1.13B, 1.14A, 1.14B, 1.15C, 1.18, 1.23 above. In cases 1.4, 1.7, 1.10, 1.15C, 1.18 and 1.23, the MS shall respond within 30 s.
1.2) The ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.3.4.3 Procedure 2 | 2a) The MS is set up with a SIM which contains NULL values in the "PLMN selector" data field. PLMN1 is the Home PLMN of the MS as defined in the IMSI. The "forbidden PLMN" data field shall contain PLMN3. the "registered PLMN" field is set to PLMN2.
2b) The SS transmits 4 BCCH carriers with the following parameters:
PLM... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.3.4.4 Requirements 2 | 2.1) The MS shall make a response as indicated in step 2d). The MS shall respond within 30 s.
Table 33-1: Normal system information fields
Parameter
Reference in 3GPP TS 04.08 / 3GPP TS 24.008 / 3GPP TS 44.018
Abbreviation
Normal setting
Cell Channel Description
10.5.2.1
-
Any values
Max retrans
10.5.2.17
-
1
Tx-intege... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.4 Invalid and blocked PIN indicators | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.4.1 Definition | - |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.4.2 Conformance requirement | Void. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.4.3 Test purpose | Void. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.4.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.4.4.1 Initial conditions | The MS contains a SIM with the PIN enabled, and the SIM unblocking counter set to zero by previous presentation of the personal unblocking key. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.4.4.2 Procedure | a) The MS is switched on.
b) Three wrong PIN are entered.
Activation may be either manual or via the EMMI. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.4.5 Test requirements | For the first and second incorrect PIN the MS shall indicate that the PIN code has been rejected.
For the third incorrect PIN the MS shall indicate that the PIN is blocked. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.5 Service indicator | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.5.1 Definition | - |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.5.2 Conformance requirement | Void. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.5.3 Test purpose | Void. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.5.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.5.4.1 Initial conditions | a) The MS is in idle mode, unregistered.
b) The SS shall emulate perfect radio conditions so that the MS is able to register and to set up or receive a call. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.5.4.2 Procedure | a) The MS is brought in an active state by either switching it on or by inserting a SIM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.5.5 Test requirements | 1) The successful registration and the good condition shall be indicated by the MS indicator and by the SS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.6 Subscription identity management | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.6.1 Definition | Subscription identity management is the ability of the MS to prevent the establishment of MO (except MO emergency calls) and MT calls without a valid subscription. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.6.2 Conformance requirement | An MS can only be operated, if a valid IMSI is present. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.6.3 Test purpose | 1) To verify that during an established call: either
1.1) on removal of the SIM from an MS, the MS will perform an IMSI detach; or
1.2) after removing the power source from the MS, removing the SIM, and restoring the power source to the MS, the MS may perform an IMSI detach.
2) To verify that an MS without SIM card wil... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.6.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.6.4.1 Initial conditions | Void. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.6.4.2 Procedure | a) A call is set up.
b) (Reserved).
c) Either:
(i) the SIM is removed; or
(ii) where this is not possible, the power source is removed from the MS, the SIM is removed and the power source is restored to the MS.
The SS observes whether or not the MS performs IMSI detach.
d) An attempt to establish a MO call is made (not... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.6.5 Test requirements | 1) Either:
1.1) in step c(i), the MS may send disconnect and shall perform an IMSI detach; or
1.2) in step c(ii), the MS sends nothing when power source is removed.
The MS may perform an IMSI detach when power is restored.
2) In step d) the MS shall not attempt to set up a new call via the Um interface.
3) In step e) t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.7 Barring of outgoing calls | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.7.1 Definition | The barring of outgoing calls is an optional feature. It is the ability of the MS to prevent all MO calls except emergency calls. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.7.2 Conformance requirement | An MS may have an optional facility to bar outgoing calls. Such barring facility shall not prevent the transmission on emergency calls. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.7.3 Test purpose | To verify that an MS for which a local facility to bar outgoing calls has been declared as being implemented, is able to establish an emergency call if this facility is activated. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.7.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.7.4.1 Initial conditions | Void. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.7.4.2 Procedure | a) The local facility to bar outgoing calls is activated.
b) Via MMI, the MS is actioned to establish an emergency call. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.7.5 Test requirements | 1) The MS shall establish an emergency call. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.8 Prevention of unauthorized calls | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.8.1 Definition | The prevention of unauthorized calls is an optional feature in the MS. It is the ability of the MS to prevent unauthorized use by using a key or keyword protection facility. When activated the MS does not prevent the establishment of except emergency calls. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.8.2 Conformance requirement | An MS may have an optional facility to prevent unauthorized use. Such facility shall not prevent the transmission on emergency calls. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.8.3 Test purpose | To verify that an MS for which a local facility to prevent unauthorized use has been declared to be implemented, is able to establish an emergency call, if this facility is activated. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.8.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.8.4.1 Initial conditions | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.8.4.2 Procedure | a) The local facility to restrict operation such that the MS can only be operated by using a key or a keyword is activated. The most restrictive situation is created.
b) Via MMI, the MS is actioned to establish an emergency call. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 33.8.5 Test requirements | 1) The MS shall establish an emergency call. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34 Short message service (SMS) | Ref.: 3GPP TS 03.40, 3GPP TS 04.11 (point to point)
3GPP TS 03.41, 3GPP TS 04.12 (cell broadcast) |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.1 General | The purpose of these tests is to verify that the MS can handle GSM functions when submitting or receiving Short Messages (SM) between MS and a short message service centre as described in 3GPP TS 03.40.
The procedures are based upon services provided by the Mobility Management (MM) sublayer which is not tested in this ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2 Short message service point to point | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.1 SMS mobile terminated | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.1.1 Conformance requirements | An active MS shall be able to receive short message TPDU (SMS-DELIVER) at any time, independently of whether or not there is a speech or data call in progress. A report will always be returned to the SC, confirming that the MS has received the short message.
Reference
3GPP TS 03.40; 3.1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.1.2 Test purpose | To verify the ability of a MS to receive and decode the SMS where provided for the point to point service. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.1.3 Method of test | Initial Conditions
System simulator:
1 cell, default parameters.
Mobile Station:
The MS shall be in "Idle, updated" state.
The SMS message storage shall be empty.
Specific PICS Statements:
- SMS messages are stored in the SIM (TSPC_AddInfo_StoreRcvSMSSIM).
- SMS messages are stored in the ME (TSPC_AddInfo_StoreRcvSMSME... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.2 SMS mobile originated | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.2.1 Conformance requirements | An active MS shall be able to submit short message TPDU (SMS-SUBMIT) at any time, independently of whether or not there is a speech or data call in progress.
Reference
3GPP TS 03.40; subclause 3.1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.2.2 Test purpose | To verify that the MS is able to correctly send a short message where the SMS is provided for the point to point service. The test also verifies that the MS is capable of simultaneously receive a network originated SM whilst sending a mobile originated SM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.2.3 Method of test | Initial Conditions
System simulator:
1 cell, default parameters.
Mobile Station:
The MS shall be in "Idle, updated" state.
The SMS message storage shall be empty.
Specific PICS Statements
- SMS messages are stored in the SIM (TSPC_AddInfo_StoreRcvSMSSIM).
- SMS messages are stored in the ME (TSPC_AddInfo_StoreRcvSMSME)... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.3 Test of memory full condition and memory available notification: | The Memory Available Notification provides a means for the MS to notify the network that it has memory available to receive one or more short messages. The SMS status field in the SIM contains status information on the "memory available" notification flag. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.3.1 Conformance requirement | 1. When a mobile terminated message is Class 2, the MS shall ensure that the message has been transferred to the SMS data field in the SIM before sending an acknowledgement to the SC. The MS shall return a protocol error message if the short message cannot be stored in the SIM and there is other short message storage a... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.3.2 Test purpose | 1. To verify that the MS sends the correct acknowledgement when its memory in the SIM becomes full.
2. To verify that the MS sends the correct acknowledgement when its memory in the ME and the SIM becomes full, and sets the "memory exceeded" notification flag in the SIM.
3. To verify that the MS performs the "memory av... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.3.3 Method of test | Initial conditions
System Simulator:
1 cell, default parameters
Mobile Station:
The MS shall be in the idle updated state.
The SMS message storage shall not be full
The MS shall be connected to the SIM simulator. The following shall be present in the SIM simulator:
- EFSMS with at least one record;
- EFSMSstatus, with... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.4 Test of the status report capabilities and of SMS-COMMAND: | This test applies to MSs which support the status report capabilities. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.4.1 Conformance requirement | The SMS offers the SC the capabilities of informing the MS of the status of a previously sent mobile originated short message. This is achieved by the SC returning a status report TPDU (SMS-STATUS-REPORT) to the originating MS.
SMS-COMMAND enables an MS to invoke an operation at the SC.
The MS shall increment TP-MR by ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.4.2 Test purpose | 1) To verify that the MS is able to accept a SMS-STATUS-REPORT TPDU.
2) To verify that the MS is able to use the SMS-COMMAND functionality correctly and sends an SMS-COMMAND TPDU with the correct TP-Message-Reference. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.4.3 Method of test | Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS shall be in the idle updated state.
Specific PICS Statements
-
PIXIT Statements
-
Foreseen Final State of MS
Idle, updated.
Test Procedure
a) The MS is made to send a Mobile Originated short message as in steps a) to d) of test 34.2... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.5 Test of message class 0 to 3 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.5.1 Short message class 0 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.5.1.1 Conformance requirement | When a mobile terminated message is class 0 and the MS has the capability of displaying short messages, the MS shall display the message immediately and send an acknowledgement to the SC when the message has successfully reached the MS irrespective of whether there is memory available in the SIM or ME. The message shal... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.5.1.2 Test purpose | To verify that the MS will accept and display but not store a class 0 message, and that it will accept and display a class 0 message if its message store is full.
NOTE: failure of this test in a mobile could cause it to reject a class 0 message when its SMS memory becomes full. This could lead to unwanted repetitions b... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 34.2.5.1.3 Method of test | Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS shall be in the idle updated state.
The MS message store shall be empty.
Specific PICS Statements
- SMS messages are stored in the SIM (TSPC_AddInfo_StoreRcvSMSSIM).
- SMS messages are stored in the ME (TSPC_AddInfo_StoreRcvSMSME).
... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.