hash stringlengths 32 32 | doc_id stringlengths 7 13 | section stringlengths 3 121 | content stringlengths 0 2.2M |
|---|---|---|---|
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 9.3.3 Narrow-Band Signal Power (NBSP) | The present document provides information on how compliance with this signal category can be achieved: To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a resistive load impedance R, shall not exceed the limits given in table 13, at any point in the frequency range 100 Hz to 30 MHz. Th... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 9.3.4 Unbalance about earth | The present document provides information on how compliance with this signal category can be achieved: To be compliant with this signal category, the balance of the signal that may flow through the LT-port or NT-port shall exceed minimum requirements, under the condition that the local loop wiring and its termination i... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10 Cluster 3 signals (symmetrical broadband) | This cluster summarizes symmetrical signals that are generated by digital transmission equipment up to 2 Mbit/s, including HDSL and SDSL. If such a system requires more than one wire-pair for carrying that bitrate, the signal description holds for each individual wire-pair. These signals are commonly used to carry serv... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.1 "HDSL.2B1Q/3" signals (392 kbaud leased lines) | This category covers signals, generated by HDSL transmission equipment on three wire-pairs, based on 2B1Q line coding. This clause is based on the ETSI reports on HDSL equipment [i.7]. These are essentially 392 kbaud systems (per wire-pair). A signal (per wire-pair) can be classified as an "HDSL.2B1Q/3 signal" if it is... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.1.1 Total signal power | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the mean signal power into a resistive load of 135 Ω shall not exceed a level of +14 dBm, measured within a frequency band from at... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.1.2 Peak amplitude | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the nominal voltage peak of the largest signal pulse into a resistive load of 135 Ω shall not exceed a level of 2,64 V (±7 %), mea... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.1.3 Narrow-Band Signal Power (NBSP) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a resistive load impedance R, shall not exceed the limits given in table 16, at any point... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.1.4 Unbalance about earth | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the balance of the signal that may flow through the LT-port or NT-port shall exceed minimum requirements, under the condition that... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.1.5 Feeding power (from the LT-port) | Power feeding is no integral part of this signal category, although it is not uncommon for HDSL services. To enable power feeding in combination with this signal category, refer to one of the power feeding classes summarized in clause 7. |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.2 "HDSL.2B1Q/2" signals (584 kbaud leased lines) | This category covers signals, generated by HDSL transmission equipment on two wire-pairs, based on 2B1Q line coding. This clause is based on the ETSI reports on HDSL equipment [i.7]. These are essentially 584 kbaud systems (per wire-pair). A signal (per wire-pair) can be classified as an "HDSL.2B1Q/2 signal" if it is c... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.2.1 Total signal power | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the mean signal power into a resistive load of 135 Ω shall not exceed a level of +14 dBm, measured within a frequency band from at... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.2.2 Peak amplitude | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the nominal voltage peak of the largest signal pulse into a resistive load of 135 Ω shall not exceed a level of 2,64 V (±7 %), mea... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.2.3 Narrow-Band Signal Power (NBSP) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a resistive load impedance R, shall not exceed the limits given in table 19, at any point... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.2.4 Unbalance about earth | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the balance of the signal that may flow through the LT-port or NT-port shall exceed minimum requirements, under the condition that... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.2.5 Feeding power (from the LT-port) | Power feeding is no integral part of this signal category, although it is not uncommon for HDSL services. To enable power feeding in combination with this signal category, refer to one of the power feeding classes summarized in clause 7. |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.3 "HDSL.2B1Q/1" signals (1 160 kbaud leased lines) | This category covers signals, generated by HDSL transmission equipment on a single wire-pair, based on 2B1Q line coding. This clause is based on the ETSI reports on HDSL equipment [i.7]. A signal (per wire-pair) can be classified as an "HDSL.2B1Q/1 signal" if it is compliant with all clauses below. Unless otherwise ind... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.3.1 Total signal power | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the mean signal power into a resistive load of 135 Ω shall not exceed a level of +14 dBm, measured within a frequency band from at... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.3.2 Peak amplitude | To be compliant with this signal category, the nominal voltage peak of the largest signal pulse into a resistive load of 135 Ω shall not exceed a level of 2,50 V (± 7 %), measured within a frequency band from at least 100 Hz to 2 320 kHz. The definition and measurement method of peak amplitude is specified in clause 13... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.3.3 Narrow-band signal power | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a resistive load impedance R, shall not exceed the limits given in table 22, at any point... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.3.4 Unbalance about earth | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the balance of the signal that may flow through the LT-port or NT-port shall exceed minimum requirements, under the condition that... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.3.5 Feeding power (from the LT-port) | Power feeding is no integral part of this signal category, although it is not uncommon for HDSL services. To enable power feeding in combination with this signal category, refer to one of the power feeding classes summarized in clause 7. |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.4 "HDSL.CAP/2" signals | This category covers signals, generated by HDSL transmission equipment on two wire-pairs, based on CAP modulation. This clause is based on the ETSI reports on HDSL equipment [i.7]. A signal (per wire-pair) can be classified as an "HDSL.CAP/2 signal" if it is compliant with all clauses below. Unless otherwise indicated,... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.4.1 Total signal power | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the mean signal power into a resistive load of 135 Ω shall not exceed a level of +14 dBm, measured within a frequency band from at... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.4.2 Peak amplitude | The present document provides information on how compliance with this signal category can be achieved: To be compliant with this signal category, the nominal voltage peak of the largest signal pulse into a resistive load of 135 Ω shall not exceed a level of 6,5 V (13 V peak-peak), measured within a frequency band from ... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.4.3 Narrow-Band Signal Power (NBSP) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a resistive load impedance R, shall not exceed the limits given in table 25, at any point... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.4.4 Unbalance about earth | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the balance of the signal that may flow through the LT-port or NT-port shall exceed minimum requirements, under the condition that... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.4.5 Feeding power (from the LT-port) | Power feeding is no integral part of this signal category, although it is not uncommon for HDSL services. To enable power feeding in combination with this signal category, refer to one of the power feeding classes summarized in clause 7. |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.5 "SDSL::Fn" signals | This category covers signals, generated by multi-rate SDSL transmission equipment on one or up to four wire pairs, up to 2 320 kb/s line rate per wire pair. This clause is based on ETSI SDSL standard [i.8] and on ITU Recommendation G.991.2 [i.9], but is not applicable to "enhanced" SDSL variants specified in annex E of... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.5.1 Total signal power | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the mean signal power into a resistive load of 135 Ω shall not exceed a level of Pmax, measured within a frequency band from at le... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.5.2 Peak amplitude | The present document provides information on how compliance with this signal category can be achieved: To be compliant with this signal category, the nominal voltage peak of the largest signal pulse into a resistive load of 135 Ω shall not exceed a level of Vpeak (± 7 %), measured within a frequency band from at least ... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.5.3 Narrow-Band Signal Power (NBSP) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a resistive load impedance R, shall not exceed the limits given in the tables in the foll... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.5.4 Unbalance about earth | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the balance of the signal that may flow through the LT-port or NT-port shall exceed minimum requirements, under the condition that... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.5.5 Feeding power (from the LT-port) | Power feeding is no integral part of this signal category, although it is not uncommon for SDSL services. To enable power feeding in combination with this signal category, refer to one of the power feeding classes summarized in clause 7. |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.6 "SDSL.asym::Fn" signals | This category covers signals, generated by multi-rate SDSL transmission equipment on one or up to four wire pairs, up to 2 320 kb/s line rate per wire pair. This clause is based on TS 101 524 [i.8] and on ITU-T Recommendation G.991.2 [i.9], but is not applicable to "enhanced" SDSL variants specified in annex E of [i.8]... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.6.1 Total signal power | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the mean signal power into a resistive load of 135 Ω shall not exceed a level of Pmax, measured within a frequency band from at le... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.6.2 Peak amplitude | The present document provides information on how compliance with this signal category can be achieved: To be compliant with this signal category, the nominal voltage peak of the largest signal pulse into a resistive load of 135 Ω shall not exceed a level of Vpeak (± 7 %), measured within a frequency band from at least ... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.6.3 Narrow-band signal power (upstream only) | This clause is dedicated to "SDSL.asym::686.NT" and "SDSL.asym::771.NT" signals only. The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a r... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.6.4 Narrow-band signal power (downstream only) | This clause is dedicated to "SDSL.asym::686.LT" and "SDSL.asym::771.LT" signals only. The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a r... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.6.5 Unbalance about earth | As for "SDSL::Fn" signal category. |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.6.6 Feeding power (from the LT-port) | Power feeding is no integral part of this signal category, although it is not uncommon for SDSL services. To enable power feeding in combination with this signal category, refer to one of the power feeding classes summarized in clause 7. |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.7 "e-SDSL::Fn" signals (enhanced SDSL) | This category covers signals, generated by multi-rate SDSL transmission equipment on one or up to four wire pairs, up to 5 696 kb/s per wire pair, as specified in annex E of ETSI SDSL standard [i.8]. This signal description is an extension to the "SDSL::Fn" signal description in a previous clause. The phrase "Fn" is a ... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.7.1 Total signal power | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the mean signal power into a resistive load of 135 Ω shall not exceed a level of Pmax, measured within a frequency band from at le... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.7.2 Peak amplitude | These definitions are identical as specified for "SDSL:Fn" signals. |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.7.3 Narrow-Band Signal Power (NBSP) | These definitions are identical as specified for "SDSL:Fn" signals, with the addition that FN can have values up to 1 426 kHz. |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.7.4 Unbalance about earth | These definitions are identical as specified for "SDSL:Fn" signals. ETSI ETSI TR 101 830-1 V1.5.2 (2009-05) 54 |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.7.5 Feeding Power (from the LT-port) | Power feeding is no integral part of this signal category, although it is not uncommon for e-SDSL services. To enable power feeding in combination with this signal category, refer to one of the power feeding classes summarized in clause 7. |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.8 "Proprietary.SymDSL.CAP.A::Fn" signals | This category covers signals, generated by Proprietary multi-rate SymDSL transmission equipment on one (or two) wire-pairs. This signal is labelled as Proprietary, since it is not covered by ETSI, ITU nor ANSI product standards. This signal definition is linecode independent, but dedicated to signals from transmission ... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.8.1 Total signal power | The present document provides information on how compliance with this signal category can be achieved: To be compliant with this signal category, the mean signal power into a resistive load of 135 Ω shall not exceed a level of +14 dBm, measured within a frequency band from at least 100 Hz to 1 MHz. NOTE: No ETSI delive... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.8.2 Peak amplitude | The present document provides information on how compliance with this signal category can be achieved: To be compliant with this signal category, the nominal voltage peak of the largest signal pulse into a resistive load of 135 Ω shall not exceed a level of 6,5 V (13 V peak-peak), measured within a frequency band from ... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.8.3 Narrow-Band Signal Power (NBSP) | The present document provides information on how compliance with this signal category can be achieved: To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a resistive load impedance R, shall not exceed the limits given in table 41, at any point in the frequency range 100 Hz to 30 MHz. Th... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.8.4 Unbalance about earth | The present document provides information on how compliance with this signal category can be achieved: To be compliant with this signal category, the balance of the signal that may flow through the LT-port or NT-port shall exceed minimum requirements, under the condition that the local loop wiring and its termination i... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.9 "Proprietary.SymDSL.CAP.B::Fn" signals | This category covers signals, generated by Proprietary multi-rate SymDSL transmission equipment. This signal is labelled as proprietary, since it is not covered by ETSI, ITU nor ANSI product standards. The pass-band signal definition is linecode independent, but derived from CAP based HDSL signals defined in annex B of... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.9.1 Total signal power | The present document provides information on how compliance with this signal category can be achieved: To be compliant with this signal category, the mean signal power into a resistive load of 135 Ω shall not exceed a level of +14 dBm, measured within a frequency band from at least 100 Hz to 1 MHz. NOTE: No ETSI delive... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.9.2 Peak amplitude | The present document provides information on how compliance with this signal category can be achieved: To be compliant with this signal category, the nominal voltage peak of the largest signal pulse into a resistive load of 135 Ω shall not exceed a level of 7,4 V measured within a frequency band from at least 100 Hz to... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.9.3 Narrow-Band Signal Power (NBSP) | The present document provides information on how compliance with this signal category can be achieved: To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a resistive load impedance R, shall not exceed the limits given in table 45, at any point in the frequency range 100 Hz to 30 MHz. Th... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 10.9.4 Unbalance about earth | The present document provides information on how compliance with this signal category can be achieved: To be compliant with this signal category, the balance of the signal that may flow through the LT-port or NT-port shall exceed minimum requirements, under the condition that the local loop wiring and its termination i... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11 Cluster 4 signals (asymmetrical broadband) | This cluster summarizes asymmetrical signals that are generated by digital transmission equipment up to 24 Mbit/s, including ADSL and ADSL2plus. Asymmetrically means a bitrate in the downstream direction and a significantly lower bitrate (e.g. 25 %) in the upstream direction. NOTE: Asymmetrical DSL systems generate dif... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.1 "ADSL/POTS (FO)" signals | This category covers signals, generated by ADSL transmission equipment, for which the downstream spectrum overlaps the upstream spectrum (Frequency Overlap). These signals may share the same wire pair with POTS signals. This clause is based on ETSI and ITU reports on ADSL equipment [i.10] and [i.11]. A signal can be cl... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.1.1 Total signal power (downstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the mean downstream signal power into a resistive load of 100 Ω shall not exceed a level of +20,4 dBm, measured within a frequency... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.1.2 Total signal power (upstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the mean upstream signal power into a resistive load of 100 Ω shall not exceed a level of +12,5 dBm, measured within a frequency b... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.1.3 Peak amplitude (upstream and downstream) | The present document provides information on how compliance with this signal category can be achieved: To be compliant with this signal category, the nominal voltage peak of the largest signal pulse into a resistive load of 100 Ω shall not exceed a level of 19V (38 V peak-peak), measured within a frequency band from at... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.1.4 Narrow-band signal power (downstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a resistive load impedance R, shall not exceed the limits given in table 66, at any point... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.1.5 Narrow-band signal power (upstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a resistive load impedance R, shall not exceed the limits given in table 68, at any point... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.1.6 Unbalance about earth (upstream and downstream) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the balance of the signal that may flow through the LT-port or NT-port shall exceed minimum requirements, under the condition that... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.2 "ADSL/POTS (FDD)" signals | This category covers signals, generated by ADSL transmission equipment, which uses Frequency Division Duplexing (FDD) to separate upstream and downstream. In this mode, the usable frequency band of downstream signals is narrower and not overlapping the upstream, but adjacent to it, to minimize self-NEXT. Therefore this... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.2.1 Total signal power (downstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the mean downstream signal power into a resistive load of 100 Ω shall not exceed a level of +19,9 dBm, measured within a frequency... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.2.2 Total signal power (upstream only) | The description of this signal characteristic equals that of "ADSL/POTS (FO)". |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.2.3 Peak amplitude (upstream and downstream) | The description of this signal characteristic equals that of "ADSL/POTS (FO)". |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.2.4 Narrow-band signal power (downstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a resistive load impedance R, shall not exceed the limits given in table 71, at any point... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.2.5 Narrow-band signal power (upstream only) | The description of this signal characteristic equals that of "ADSL/POTS (FO)". |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.2.6 Unbalance about earth (upstream and downstream) | The description of this signal characteristic equals that of "ADSL/POTS (FO)". |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.3 "ADSL/ISDN (FO)" signals | This category covers signals, generated by ADSL transmission equipment, for which the downstream spectrum overlaps the upstream spectrum (Frequency Overlap). These signals may share the same wire pair with ISDN signals. This clause is based on ETSI and ITU reports on ADSL equipment [i.10] and [i.11]. A signal can be cl... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.3.1 Total signal power (downstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the mean downstream signal power into a resistive load of 100 Ω shall not exceed a level of +19,9 dBm, measured within a frequency... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.3.2 Total signal power (upstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the mean upstream signal power into a resistive load of 100 Ω shall not exceed a level of +13,3 dBm, measured within a frequency b... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.3.3 Peak amplitude (upstream and downstream) | The present document provides information on how compliance with this signal category can be achieved: To be compliant with this signal category, the nominal voltage peak of the largest signal pulse into a resistive load of 100 Ω shall not exceed a level of 19 V (38 V peak-peak), measured within a frequency band from a... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.3.4 Narrow-band signal power (downstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a resistive load impedance R, shall not exceed the limits given in table 73, at any point... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.3.5 Narrow-band signal power (upstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a resistive load impedance R, shall not exceed the limits given in table 75, at any point... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.3.6 Unbalance about earth (upstream and downstream) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the balance of the signal that may flow through the LT-port or NT-port shall exceed minimum requirements, under the condition that... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.4 "ADSL/ISDN (FDD)" signals | This category covers signals, generated by ADSL transmission equipment which uses Frequency Division Duplexing (FDD) to separate upstream and downstream. In this mode, the usable frequency band of downstream signals is narrower to limit the overlap with the upstream to four DMT tones. This is to minimize self-NEXT. The... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.4.1 Total signal power (downstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the mean downstream signal power into a resistive load of 100 Ω shall not exceed a level of +19,3 dBm, measured within a frequency... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.4.2 Total signal power (upstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the mean upstream signal power into a resistive load of 100 Ω shall not exceed a level of +13,3 dBm, measured within a frequency b... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.4.3 Peak amplitude (upstream and downstream) | The description of this signal characteristic equals that of "ADSL/ISDN (FO)". |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.4.4 Narrow-band signal power (downstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a resistive load impedance R, shall not exceed the limits given in table 73, at any point... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.4.5 Narrow-band signal power (upstream only) | The description of this signal characteristic equals that of " ADSL/ISDN (FO)". |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.4.6 Unbalance about earth (upstream and downstream) | The description of this signal characteristic equals that of " ADSL/ISDN (FO)". |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.5 "ADSL2plus/A (FO)" signals (over POTS) | This category covers signals, generated by ADSL2plus transmission equipment, for which the downstream spectrum overlaps the upstream spectrum (Frequency Overlap). These signals may share the same wire pair with POTS signals. This clause is based on ITU-T Recommendation G.992.5 [i.12]. A signal can be classified as an "... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.5.1 Total signal power (downstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the mean downstream signal power into a resistive load of 100 Ω shall not exceed a level of +20,4 dBm, measured within a frequency... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.5.2 Total signal power (upstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the mean upstream signal power into a resistive load of 100 Ω shall not exceed a level of +12,5 dBm, measured within a frequency b... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.5.3 Peak amplitude (upstream and downstream) | The present document provides information on how compliance with this signal category can be achieved: To be compliant with this signal category, the nominal voltage peak of the largest signal pulse into a resistive load of 100 Ω shall not exceed a level of 19V (38 V peak-peak), measured within a frequency band from at... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.5.4 Narrow-band signal power (downstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a resistive load impedance R, shall not exceed the limits given in table 80 at any point ... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.5.5 Narrow-band signal power (upstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a resistive load impedance R, shall not exceed the limits given in table 81, at any point... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.5.6 Unbalance about earth (upstream and downstream) | The present document provides information on how compliance with this signal category can be achieved: To be compliant with this signal category, the balance of the signal that may flow through the LT-port or NT-port shall exceed minimum requirements, under the condition that the local loop wiring and its termination i... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.6 "ADSL2plus/A (FDD)" signals (over POTS) | This category covers signals, generated by ADSL2plus transmission equipment, which uses Frequency Division Duplexing (FDD) to separate upstream and downstream. In this mode, the usable frequency band of downstream signals is narrower and not overlapping the upstream, but adjacent to it, to minimize self-NEXT. Therefore... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.6.1 Total signal power (downstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the mean downstream signal power into a resistive load of 100 Ω shall not exceed a level of +19,9 dBm, measured within a frequency... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.6.2 Total signal power (upstream only) | The description of this signal characteristic equals that of "ADSL2plus/A (FO)". |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.6.3 Peak amplitude (upstream and downstream) | The description of this signal characteristic equals that of "ADSL2plus/A (FO)". |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.6.4 Narrow-band signal power (downstream only) | The present document provides information on how compliance with this signal category can be achieved and indicates the relevant specification(s): To be compliant with this signal category, the Narrow-Band Signal Power (NBSP) into a resistive load impedance R, shall not exceed the limits given in table 84, at any point... |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.6.5 Narrow-band signal power (upstream only) | The description of this signal characteristic equals that of "ADSL2plus/A (FO)". |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.6.6 Unbalance about earth (upstream and downstream) | The description of this signal characteristic equals that of "ADSL2plus/A (FO)". |
32347bacbd44eee2fd8cd2c5065911f1 | 101 830-1 | 11.7 "ADSL2plus/B (FO)" signals (over ISDN) | This category covers signals, generated by ADSL2plus transmission equipment, for which the downstream spectrum overlaps the upstream spectrum (Frequency Overlap). These signals may share the same wire pair with ISDN signals. This clause is based on ITU-T Recommendation G.992.5 [i.12]. A signal can be classified as an "... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.