hash stringlengths 32 32 | doc_id stringlengths 7 13 | section stringlengths 3 121 | content stringlengths 0 2.2M |
|---|---|---|---|
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 7.2.4.1.1 Uplink routing as a router | Field Description TP id DECTNR/DLC/ROU/01 Test objective Check that the IUT routes an uplink packet towards the backend Reference ETSI TS 103 636-5 [5], clause 5.2.8.2 Mode FT-PT Config CF04 or CF06 PICS Selection pc_dlc_routing_000 Initial conditions with { IUT having an association to LT_FT } ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 45 Expected behaviour ensure that { when { IUT receives a packet containing DLC PDU containing a Routing header indicating "Dest_Add": '010'b ("Destination Address is backend") and indicating "Routing type": '000'b ("Uplink hop-by-hop routing") } then { IUT sends a packet containing DLC PDU to LT_FT } } |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 7.2.4.1.2 Uplink routing as a destination | Field Description TP id DECTNR/DLC/ROU/02 Test objective Check that the IUT having backend connectivity provides the received DLC SDU to the CVG layer at the backend interface Reference ETSI TS 103 636-5 [5], clause 5.2.8.2 Mode FT Config CF02 PICS Selection pc_dlc_routing_000 Initial conditions with { IUT operating as a sink and having a connection to the backend } Expected behaviour ensure that { when { IUT receives a packet containing DLC PDU containing a Routing header indicating "Dest_Add": '010'b ("Destination Address is backend") } then { IUT provides the DLC SDU to the upper layer } } |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 7.2.4.2 Packet Routing from backend (downlink) | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 7.2.4.2.1 Unicast as a destination | Field Description TP id DECTNR/DLC/ROU/03 Test objective Check that the IUT receives a packet when the routing header indicates it as the destination Reference ETSI TS 103 636-5 [5], clause 5.2.8.2 Mode PT or FT-PT Config IF Mode = PT THEN CF03 IF Mode = FT-PT THEN CF06 PICS Selection pc_dlc_routing_011 Initial conditions with { IUT having an association to LT_FT } Expected behaviour ensure that { when { IUT receives a packet containing DLC PDU containing a Routing header indicating "Dest_Add": ('000'b, or '011'b) (Destination Address is present) and indicating "Routing type": '011'b ("Downlink flooding") and indicating "Destination address": IUT's Long RD ID ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 46 } then { IUT passes the DLC SDU to the upper layer } } |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 7.2.4.2.2 Unicast destination with direct connection | Field Description TP id DECTNR/DLC/ROU/04 Test objective Check that the IUT routes a downlink unicast packet to its destination when it is an associated RD Reference ETSI TS 103 636-5 [5], clause 5.2.8.2 Mode FT-PT Config CF04 PICS Selection pc_dlc_routing_011 Initial conditions with { IUT having an association to LT_FT and LT_PT having an association to IUT } Expected behaviour ensure that { when { IUT receives a packet containing DLC PDU containing a Routing header indicating "Dest_Add": ('000'b or '011'b) (Destination Address is present) and indicating "Routing type": '011'b ("Downlink flooding") and indicating "Destination address": Long RD ID of LT_PT } then { IUT sends a packet containing DLC PDU containing the received DLC SDU to LT_PT } } |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 7.2.4.2.3 Unicast destination without direct connection | Field Description TP id DECTNR/DLC/ROU/05 Test objective Check that the IUT routes a downlink unicast packet by flooding when the destination is not an associated RD Reference ETSI TS 103 636-5 [5], clause 5.2.8.2 Mode FT-PT Config CF06 PICS Selection pc_dlc_routing_011 Initial conditions with { IUT having an association to LT_FT and LT_PT having an association to IUT and LT_FT_PT having an association to IUT } Expected behaviour ensure that { when { IUT receives a packet containing DLC PDU containing a Routing header indicating "Dest_Add": ('000'b or '011'b) (Destination Address is present) and indicating "Routing type": '011'b ("Downlink flooding") and not indicating "Destination address": Long RD ID of LT_PT or LT_FT_PT } then { IUT sends a packet containing DLC PDU containing the received DLC SDU ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 47 to LT_FT_PT } } |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 7.2.4.2.4 Broadcast destination | Field Description TP id DECTNR/DLC/ROU/06 Test objective Check that the IUT routes a broadcast packet to all associated RDs Reference ETSI TS 103 636-5 [5], clause 5.2.8.2 Mode FT-PT Config CF06 PICS Selection pc_dlc_routing_011 Initial conditions with { IUT having an association to LT_FT and LT_PT having an association to IUT and LT_FT_PT having an association to IUT } Expected behaviour ensure that { when { IUT receives a packet containing DLC PDU containing a Routing header indicating "Dest_Add": '100'b ("Destination Address is broadcast address") and indicating "Routing type": '011'b ("Downlink flooding") } then { IUT passes the DLC SDU to the upper layer and sends a packet containing DLC PDU containing the received DLC SDU to LT_PT and sends a packet containing DLC PDU containing the received DLC SDU to LT_FT_PT } } |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 7.3 CVG | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 7.3.1 Transparent procedure | Void. |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 7.3.2 Multiplexing procedures | Void. ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 48 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 7.3.3 Duplicate removal procedure | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 7.3.3.1 Duplicate CVG SDU | Field Description TP id DECTNR/CVG/DR/01 Test objective Check that the IUT discards a duplicate CVG PDU on reception Reference ETSI TS 103 636-5 [5], clause 6.2.5 Mode FT or PT Config IF Mode = FT THEN CF02 IF Mode = PT THEN CF03 PICS Selection pc_cvg_dup Initial conditions with { IUT having received a packet containing CVG PDU containing Data EP IE indicating "Sequence Number": Any } Expected behaviour ensure that { when { IUT receives a packet containing CVG PDU containing Data EP IE indicating "Sequence Number": Same as in the initial condition } then { IUT discards the CVG PDU } } |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 7.3.4 Delivery Order procedures | Void. |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 7.3.5 CVG Segmentation | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 7.3.5.1 Segmentation Indication 01 | Field Description TP id DECTNR/CVG/SEG/01 Test objective Check that the IUT correctly sends a first segment of a CVG PDU Reference ETSI TS 103 636-5 [5], clause 6.2.7 Mode FT or PT Config IF Mode = FT THEN CF02 IF Mode = PT THEN CF03 PICS Selection pc_cvg_st2, pc_cvg_st3, pc_cvg_st4 Initial conditions with { IUT having a CVG SDU to be sent } Expected behaviour ensure that { when { The CVG SDU does not fit in the CVG PDU as a whole } then { IUT sends a packet containing CVG PDU containing Data IE or Data EP IE indicating "SI": '01'b ("First segment") and containing Payload: The first segment of the CVG SDU } } ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 49 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 7.3.5.2 Segmentation Indication 11 | Field Description TP id DECTNR/CVG/SEG/02 Test objective Check that the IUT correctly sends a intermediate segment of a CVG PDU Reference ETSI TS 103 636-5 [5], clause 6.2.7 Mode FT or PT Config IF Mode = FT THEN CF02 IF Mode = PT THEN CF03 PICS Selection pc_cvg_st2, pc_cvg_st3, pc_cvg_st4 Initial conditions with { IUT having sent a packet containing CVG PDU containing Data IE or Data EP IE indicating "SI": '01'b, or '11'b (Initial or intermediate segment) and indicating "Sequence Number": Any and containing Payload: CVG SDU segment } Expected behaviour ensure that { when { IUT has an intermediate CVG SDU segment to be sent } then { IUT sends a packet containing CVG PDU containing Data IE or Data EP IE indicating "SI": '11'b ("Intermediate segment") and indicating "Sequence Number": Same as in the initial condition and indicating "Segmentation offset": Equal to the total size of previous segments and containing Payload: CVG SDU segment } } |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 7.3.5.3 Segmentation Indication 10 | Field Description TP id DECTNR/CVG/SEG/03 Test objective Check that the IUT correctly sends the last segment of a CVG PDU Reference ETSI TS 103 636-5 [5], clause 6.2.7 Mode FT or PT Config IF Mode = FT THEN CF02 IF Mode = PT THEN CF03 PICS Selection pc_cvg_st2, pc_cvg_st3, pc_cvg_st4 Initial conditions with { IUT having sent a packet containing CVG PDU containing Data IE or Data EP IE indicating "SI": '01'b, or '11'b (Initial or intermediate segment) and indicating "Sequence Number": Any and containing Payload: CVG SDU segment } Expected behaviour ensure that { when { IUT has the last CVG SDU segment to be sent } then { IUT sends a CVG PDU containing Data IE or Data EP IE indicating "SI": '10'b ("Last segment") and indicating "Sequence Number": Same as in the initial condition and indicating "Segmentation offset": Equal to the total size of previous segments and containing Payload: CVG SDU segment with last octets of the SDU. } } ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 50 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8 Test Descriptions | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1 MAC Test Descriptions | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1 Spectrum Management Procedures | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.1 Beaconing Transmission | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.1.1 Test Purpose | Table 8.1.1.1.1-1: Test Purpose to sequence mapping Test Name Reference TP Validity of Network Beacon message 7.1.1.1.1 1 Network Beacon Period 7.1.1.1.4 2 Cluster Beacon according to Network Beacon information 7.1.1.1.7 3 Validity of Cluster Beacon message 7.1.1.1.2 4 Cluster Beacon Period 7.1.1.1.5 5 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.1.2 Test Applicability | This test is applicable according to the following PICS parameters. Table 8.1.1.1.2-1: PICS selection parameters PICS selection Description Status pc_mac_ft FT mode m pc_mac_bea_cluster_tx Support Cluster Beacon transmission m |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.1.3 Pre-Test Conditions | Prerequisite tests: • None Test System: • Configuration: CF01 EUT: • Mode: FT Preamble: • EUT is switched on PICS & PIXIT parameters: Table 8.1.1.1.3-1: Additional PICS parameters PICS parameter Description Status pc_mac_bea_network_tx Support Network Beacon transmission o pc_dect_mesh Mesh Network Topology o pc_mac_sec Support MAC Security procedures o pc_smcb Smart Metering, City and Buildings o ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 51 Table 8.1.1.1.3-2: PIXIT parameters PIXIT parameter Description Status px_network_channel The channel(s) where EUT transmits Network Beacons c.1 c.1: IF pc_mac_bea_network_tx THEN m ELSE n/a. |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.1.4 Test Procedure Sequence | Table 8.1.1.1.4-1: Test Sequence Step Procedure Message Sequence TP Verdict EUT-TS Message - EXCEPTION: IF pc_mac_bea_network_tx THEN Steps 1a1 to 1a5 are performed ELSE Steps 1b1 to 1b2 are performed. 1a1 Check: Does the EUT transmit a Network Beacon to px_network_channel? --> Network Beacon message - P 1a2 Check: Does the EUT transmit a valid Network Beacon in step 1a1? - - 1 P 1a3 Check: Does the EUT transmit 10 Network Beacon(s) with the average periodicity "Network beacon period" after step 1a2? --> Network Beacon message x 10 2 P 1a4 Check: Does the EUT transmit a Cluster Beacon at the time indicated in "Time to next" after step 1a3, on the channel indicated as "Next Cluster channel"? --> Cluster Beacon message 3 P 1a5 Check: Does the EUT transmit a valid Cluster Beacon in step 1a4? - - 4 P 1b1 The EUT transmits a Cluster Beacon on the operating channel. --> Cluster Beacon message - - 1b2 Check: Does the EUT transmit a valid Cluster Beacon in step 1b1? - - 4 P 2 Check: Does the EUT transmit another Cluster Beacon at the time indicated in "Cluster Beacon period"? --> Cluster Beacon message 5 P |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.2 Operating Channel(s) and Subslot(s) selection | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.2.1 Test Purpose | Table 8.1.1.2.1-1: Test Purpose to sequence mapping Test Name Reference TP Channel Selection within the operating band 7.1.1.2.1 1 Selection of suitable channel resources 7.1.1.2.2 2 Next Cluster Channel in Cluster Beacon message 7.1.1.1.3 3 Time to Next Cluster Beacon transmission 7.1.1.1.6 4 Operating channel re-selection 7.1.1.2.3 5 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.2.2 Test Applicability | This test is applicable according to the following PICS parameters. Table 8.1.1.2.2-1: PICS selection parameters PICS Selection Description Status pc_mac_ft FT mode m pc_mac_ocs Support Operation Channel and Subslot selection procedure m ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 52 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.2.3 Pre-Test Conditions | Prerequisite tests: • Beaconing transmission Test System: • Configuration: CF01 EUT: • Mode: FT Preamble: • EUT is switched off PICS & PIXIT parameters: Table 8.1.1.2.3-1: Additional PICS parameters PICS parameter Description Status pc_mac_ocs_reselect Support Operating Channel and Subslot re-selection o pc_mac_bea_network_tx Support Network Beacon transmission o pc_mac_bea_cluster_nc Support "Next Channel" for a Cluster Beacon o pc_mac_bea_cluster_ttn Support "Time to next" for a Cluster Beacon o Table 8.1.1.2.3-2: PIXIT parameters PIXIT parameter Description Status px_network_channel The channel(s) where EUT transmits Network Beacons c.1 px_operating_band The operating band(s) of the EUT m c.1: IF pc_mac_bea_network_tx THEN m ELSE n/a. |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.2.4 Test Procedure Sequence | Table 8.1.1.2.4-1: AWGN interference signal properties Type Parameter Value Remark 1 Bandwidth 50 % of the operating band Bandwidth to cover 50 % of the operating band Power level at EUT input > RSSI_THRESHOLD_MAX+ InterferenceMargin RSSI_THRESHOLD_MAX as defined in ETSI TS 103 636-4 [4], clause 5.1.2 Notes 1 and 2 Centre frequency Set to cover the lower/upper 50 % of the operating band Duty cycle 100 % Continuous interference 2 Bandwidth B Nominal channel bandwidth Power level at EUT input Set to same as in Type 1 Threshold as defined in ETSI TS 103 636-4 [4], clause 5.1.2 Centre frequency Centre of the operating channel of the EUT Set to a single channel Duty cycle 100 % Continuous interference InterferenceMargin is the sum of the RSSI-2 Measurement accuracy (positive value) and the error caused by the RSSI-2 measurement report mapping as defined in ETSI TS 103 636-2 [2] on clause 8.3. NOTE 1: RSSI_THRESHOLD_MAX is set to the value defined for the band where the test is performed. NOTE 2: When setting the InterferenceMargin the TS should consider its own transmission output power tolerance to ensure the correct power level at the input of the EUT. ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 53 Table 8.1.1.2.4-2: Test Sequence Step Procedure Message Sequence TP Verdict EUT-TS Message 1 The TS transmits an interference signal according to field "Type 1" in Table 8.1.1.2.4-1. <-- AWGN interference - - 2 EUT is switched on. - - - - 3 The EUT measures the RSSI-1 values of the channels on the selected operating band (px_operating_band) and selects a suitable channel(s). - - - - - EXCEPTION: Steps 4 to 6 are performed IF pc_mac_bea_network_tx AND channel px_network_channel does not contain interference. - - - - 4 The EUT transmits a Network Beacon message on the channel px_network_channel. --> Network Beacon message - - 5 Check: Does the Network Beacon message value for "Next Cluster channel" belong in the range of absolute channel numbers defined for the operating band as defined in Table 5.4.2-1 in ETSI TS 103 636-2 [2]? --> Network Beacon message 1 P 6 Check: Does the "Network Beacon message" value for "Next Cluster channel" indicate a channel which is not interfered by the interference signal? --> Network Beacon message 2 P 7 Check: Does the EUT transmit a Cluster Beacon message on a channel not containing interference? (see note) --> Cluster Beacon message 2 P - EXCEPTION: The steps 8 to 14 are performed IF pc_mac_ocs_reselect. - - - - - EXCEPTION: The steps 8 to 11 may be repeated multiple times to verify that the channel is always selected correctly. - - - - 8 The TS transmits an interference signal according to field "Type 2" in Table 8.1.1.2.4-1. - - - - 9 Check: Does the EUT continue to transmit Cluster Beacon messages? --> Cluster Beacon message - - - EXCEPTION: The steps 10a1 to 10b2 define sequences which are performed depending on PICS parameters. - - - - 10a1 IF pc_mac_bea_cluster_nc THEN When: The EUT transmits a Cluster Beacon indicating "Next Cluster Channel" after step 9. --> - - - 10a2 Check: Does the EUT transmit the next Cluster Beacon message on channel indicated in "Next Cluster Channel"? - - 3 P 10b1 IF pc_mac_bea_cluster_ttn THEN When: The EUT transmits a Cluster Beacon indicating "Time to next" after step 9. --> Cluster Beacon message - - 10b2 Check: Does the EUT transmit the next Cluster Beacon message at "Time to next"? - - 4 P 11 Check: Does the EUT transmit a Cluster Beacon message on a channel which is not interfered by the interference "Type 1" nor "Type 2" at least within timer scanStatusValid after step 8? --> Cluster Beacon message 5 P 12 IF pc_mac_bea_network_tx THEN perform steps 5 to 6. - - - - 13 The EUT is switched off. 14 Repeat steps 1 to 13 by using the other 50 % of the operating band for the "Type 1" interference at step 1. - - - - NOTE: With some combinations of nominal signal bandwidth (> 1,728 MHz) and operating band, adjacent operating channel frequencies overlap. Therefore, covering one channel with interference will also interfere the next channel. ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 54 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.3 Power Control | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.3.1 Initial Transmit Power | 8.1.1.3.1.1 Test Purpose Table 8.1.1.3.1.1-1: Test Purpose to sequence mapping Test Name Reference TP Power control for initial transmission 7.1.1.3.1 1 8.1.1.3.1.2 Test Applicability This test is applicable according to the following PICS parameters. Table 8.1.1.3.1.2-1: PICS selection parameters PICS Selection Description Status pc_smcb Smart Metering, City and Buildings m pc_mac_pt PT mode m pc_smcb_mac_pc_initial Support initial transmission power control m 8.1.1.3.1.3 Pre-Test Conditions Prerequisite tests: • Transmission on Random-Access Resources • Association Procedure Test System: • Configuration: CF03 (LT_TC + LT_FT) EUT: • Mode: PT Preamble: • The EUT is switched off PICS & PIXIT parameters: Table 8.1.1.3.1.3-1: Additional PICS parameters PICS parameter Description Status pc_mac_pc_tx_power_max Highest transmission power level supported by the EUT m ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 55 8.1.1.3.1.4 Test Procedure sequence Table 8.1.1.3.1.4-1: Test sequence Step Procedure Message Sequence TP Verdict EUT-TS Message - EXCEPTION: The steps 1 to 6 are repeated for the following values of PathLoss: 63 dB - MaxTXComp, 80 dB - MaxTXComp, 100 dB - MaxTXComp and 120 dB – MaxTXComp. Note 1. - - - - 1 The system path loss is set at PathLoss. - - - - 2 The EUT is switched on. - - - - 3 The TS transmits Cluster Beacon message(s). <-- Cluster Beacon message - - 4 Check: Does the EUT transmit an Association Request message indicating Transmit Power level less or equal to RX_Power + PathLoss + PowerMargin? See notes 2 and 3. --> Association Request message 1 P 5 The TS transmits an Association Response message. <-- Association Response message - - 6 The EUT is switched off. - - - - NOTE 1: MaxTXComp = 23 dBm - pc_mac_pc_tx_power_max. (Maximum TX power of the RD Power Class as defined ETSI TS 103 636-2 [2] in clause 6.2). NOTE 2: PowerMargin is the sum of the RSSI-2 Measurement accuracy (positive value) and the error caused by the RSSI-2 measurement report mapping as defined in ETSI TS 103 636-2 [2] in clause 8.3. NOTE 3: RX_Power is defined in ETSI TS 103 874-2 [7] as -88 dBm. |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.3.2 Dynamic Power Control | 8.1.1.3.2.1 Test Purpose Table 8.1.1.3.2.1-1: Test Purpose to sequence mapping Test Name Reference TP Maximum transmission power in a cluster 7.1.1.3.2 1 8.1.1.3.2.2 Test Applicability This test is applicable according to the following PICS parameters. Table 8.1.1.3.2.2-1: PICS selection parameters PICS Selection Description Status pc_mac_pt PT mode m pc_mac_pc Support Power Control m 8.1.1.3.2.3 Pre-Test Conditions Prerequisite tests: • Transmission on Random-Access Resources • Random-Access Data Transmission • HARQ Transmission • Association Procedure Test System: • Configuration: CF03 (LT_TC + LT_FT) ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 56 • The transmission power level of the Cluster Beacon messages transmitted by the Test System are set one step below the PICS parameter pc_mac_pc_tx_power_max, as defined in Table 6.2.1-3a of ETSI TS 103 636-4 [4]. EUT: • Mode: PT Preamble: • EUT in PT mode associated to another RD, according to Table 8.4.3.2-1 • Test Mode on PICS & PIXIT parameters: Table 8.1.1.3.2.3-1: Additional PICS parameters PICS Selection Description Status pc_mac_pc_tx_power_min Lowest transmission power level supported by the EUT m pc_mac_pc_tx_power_max Highest transmission power level supported by the EUT m pc_mac_pc_target_bler Target BLER percentage of the EUT m Table 8.1.1.3.2.3-2: PIXIT parameters PIXIT parameter Description Status px_min_sensitivity_level RD sensitivity level in dBm m 8.1.1.3.2.4 Test Procedure sequence Table 8.1.1.3.2.4-1: Test sequence (Part 1: Power Up) Step Procedure Message Sequence TP Verdict EUT-TS Message 1 Set the system path loss such that the EUT signal level at the TS input when using Transmit Power pc_mac_pc_tx_power_min is ~10 dB above the px_min_sensitivity_level. - - - - - EXCEPTION: The steps 2 to 7 are repeated until the EUT has reached the Transmit Power pc_mac_pc_tx_power_max. - - - - 2 The TS transmits a Data Request message indicating: request_flags: 0x80 (HARQ), request_t_interval: 0x0a (100 ms), request_n_packets: 0x64 (100 packets), request_n_bytes: 0x000a (10-byte data payload). <-- TMC: Data Request - - - EXCEPTION: The steps 3 to 4 are repeated until all packets requested in step 2 have been transmitted. - - - - 3 The EUT transmits a packet containing a MAC PDU. --> TMC: Data Request Response - - 4 The TS transmits a packet containing Transmission Feedback indicating ACK or NACK. <-- ACK/NACK - - 5 Check: Does the EUT reach a BLER of pc_mac_pc_bler_target for the transmissions in step 3? This may be checked from the number of re-transmissions done by the EUT. - - - P ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 57 Step Procedure Message Sequence TP Verdict EUT-TS Message 6 Check: Does the EUT transmit a packet indicating transmission power level less or equal than indicated by the TS in the Cluster Beacon messages, for all transmissions of step 3? (see note) - - PC/02 P 7 The system path loss is increased by 10 dB. - - - - NOTE: The transmission power limit implicitly comes from the Physical Layer Control Field if not explicitly indicated in the Cluster Beacon IE. Table 8.1.1.3.2.4-2: Test sequence (Part 2: Power Down) Step Procedure Message Sequence TP Verdict EUT-TS Message 1 Set the system path loss such that the EUT signal level at the TS input when using Transmit Power pc_mac_pc_tx_power_max is ~10 dB above the px_min_sensitivity_level. - - - - - EXCEPTION: The steps 2 to 7 are repeated until the additional system path loss is completely removed or when the EUT has reached the Transmit Power pc_mac_pc_tx_power_min. - - - - 2 The TS transmits a Data Request message indicating: request_flags: 0x00 (No HARQ), request_t_interval: 0x0a (100 ms), request_n_packets: 0x64 (100 packets), request_n_bytes: 0x000a (10-byte data payload). <-- TMC: Data Request - - EXCEPTION: The steps 3 to 4 are repeated until all packets requested in step 2 have been transmitted. - - - - 3 The EUT transmits a packet containing a MAC PDU. --> TMC: Data Request Response - - 4 The TS transmits a packet containing Transmission Feedback indicating ACK or NACK. <-- ACK/NACK - - 5 Check: Does the EUT reach a BLER of pc_mac_pc_target_bler for the transmissions in step 3? This may be checked from the number of re-transmissions done by the EUT. - - - P 6 IF the target BLER was reached in the previous execution of step 5 THEN Check: Does the EUT lower its Transmit Power or increase the MCS in comparison to the previous repetition? - - - P 7 The system path loss is lowered by 10 dB. - - - - |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.4 Selecting RD for association | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.4.1 Test Purpose | Table 8.1.1.4.1-1: Test Purpose to sequence mapping Test Name Reference TP Selection based on minimum quality 7.1.1.4.1 1 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.4.2 Test Applicability | This test is applicable according to the following PICS parameters. ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 58 Table 8.1.1.4.2-1: PICS selection parameters PICS Selection Description Status pc_mac_pt PT mode m pc_mac_rds Support RD selection for association m |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.4.3 Pre-Test Conditions | Prerequisite tests: • Transmission on Random-Access Resources • Association Request and Release Test System: • Configuration: CF05 EUT: • Mode: PT Preamble: • The EUT is switched off PIXIT parameters: Table 8.1.1.4.3-1: PIXIT parameters PIXIT parameter Description Status px_min_sensitivity_level RD sensitivity level in dBm m |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.1.4.4 Test Procedure Sequences | Table 8.1.1.4.4-1: Test System RSSI-2 configuration Type LT Target RSSI-2 level of beacon transmissions at EUT input (dBm) T1 FT1 px_min_sensitivity_level + MIN_QUALITY + 10 dB + PowerMargin FT2 px_min_sensitivity_level + MIN_QUALITY - 10 dB - PowerMargin PowerMargin is the sum of the RSSI-2 Measurement accuracy (positive value) and the error caused by the RSSI-2 measurement report mapping as defined in ETSI TS 103 636-2 [2] on clause 8.3. NOTE 1: MIN_QUALITY is signalled in the Cluster Beacon IE. NOTE 2: When setting the PowerMargin the TS should consider its own transmission output power tolerance to ensure the correct power level at the input of the EUT. Table 8.1.1.4.4-2: Test System Route Cost Configuration Type LT Route cost T1 FT1 Not present or 1 FT2 Not present or 1 ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 59 Table 8.1.1.4.4-3: Test sequence Step Procedure Message Sequence TP Verdict EUT-TS Message 1 The TS (FT1 and FT2) transmit Cluster beacon messages, with values according to row "T1" in Table 8.1.1.4.4-1 and row "T1" in Table 8.1.1.4.4-2. <-- Cluster Beacon message - - 2 EUT is switched on. - - - - 3 Check: Does the EUT transmit an Association Request message to FT1? --> Association Request message 1 P 4 The TS (FT1) transmits an Association Response message as a random-access response, indicating ACK. <-- Association Response message - - |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.2 Broadcast Procedure | Void. |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3 Random Access Procedure | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.1a Transmission on Random-Access resources received from beacon message | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.1a.1 Test Purpose | Table 8.1.3.1a.1-1: Test Purpose to sequence mapping Test Name Reference TP Transmission on random-access resources received from beacon message 7.1.3.1.1a 1 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.1a.2 Test Applicability | This test is applicable according to the following PICS parameters. Table 8.1.3.1a.2-1: PICS selection parameters PICS Selection Description Status pc_mac_pt PT mode m pc_mac_rach_tx Support Random Access Transmission m |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.1a.3 Pre-Test conditions | Prerequisite tests: • None Test System: • Configuration: CF03 EUT: • Mode: PT Preamble: • The EUT is switched on ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 60 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.1a.4 Test Procedure Sequence | Table 8.1.3.1a.4-1: Test sequence Step Procedure Message Sequence TP Verdict EUT-TS Message 1 The TS transmits periodic Cluster Beacon messages. <-- Cluster Beacon message - - 2 Command the EUT to transmit a packet to the TS. - - - - 3a Check: Does the EUT transmit the packet to the random-access resources? --> MAC PDU 1 P 3b The TS transmits a random-access response within random-access response window. - - - - |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.1b Transmission on Random-Access resources received in unicast message | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.1b.1 Test Purpose | Table 8.1.3.1b.1-1: Test Purpose to sequence mapping Test Name Reference TP Transmission on random-access resources received from unicast signalling 7.1.3.1.1b 1 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.1b.2 Test Applicability | This test is applicable according to the following PICS parameters. Table 8.1.3.1b.2-1: PICS selection parameters PICS Selection Description Status pc_smcb Smart Metering, City and Buildings m pc_mac_ft FT mode m pc_mac_rach_tx Support Random Access Transmission m |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.1b.3 Pre-Test conditions | Prerequisite tests: • Random Access Reception and Response Test System: • Configuration: CF02 EUT: • Mode: FT Preamble: • EUT in FT mode associated to another RD, according to Table 8.4.2.2-1 ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 61 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.1b.4 Test Procedure Sequence | Table 8.1.3.1b.4-1: Test sequence Step Procedure Message Sequence TP Verdict EUT-TS Message 1 The EUT transmits a Cluster Beacon message. --> Cluster Beacon message - - 2 The TS transmits a Data Request message indicating: request_flags: 0x80 (HARQ), request_t_interval: 0x13 (1 second), request_n_packets: 0x0A (10 packets), request_n_bytes: 0x000a (10-byte data payload). <-- TMC: Data Request - - 3 The EUT transmits a random-access response. --> - - - 4 Check: Does the EUT transmit a packet containing Data Request Response message? --> TMC: Data Request Response 1 P 5 The TS transmits a random-access response within random-access response window. - - - - NOTE: The EUT should not transmit a Data Request Response message within the random-access response due to the delay. |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.2 Listen Before Talk | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.2.1 Test Purpose | Table 8.1.3.2.1-1: Test Purpose to sequence mapping Test Name Reference TP Listen Before Talk 7.1.3.1.2 1 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.2.2 Test Applicability | This test is applicable according to the following PICS parameters. Table 8.1.3.2.2-1: PICS selection parameters PICS Selection Description Status pc_mac_pt PT mode m pc_mac_rach_tx Support Random Access Transmission m |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.2.3 Pre-Test conditions | Prerequisite tests: • Transmission on Random-Access Resources • Association Request and Release Test System: • Configuration: CF03 EUT: • Mode: PT Preamble: • EUT in PT mode associated to another RD, according to Table 8.4.3.2-1 • Test mode on ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 62 Table 8.1.3.2.3-1: Interference signal properties Type Parameter Value Remark 1 Bandwidth B Nominal channel bandwidth Power level at EUT input P RSSI_THRESHOLD_MAX + InterferenceMargin Centre frequency Centre of the operating channel of the EUT Set to a single channel Duty cycle 100 % Continuous interference NOTE 1: RSSI_THRESHOLD_MAX is set to value defined for the band where the test is performed. NOTE 2: InterferenceMargin as defined in Table 8.1.1.2.4-1. |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.2.4 Test Procedure Sequence | Table 8.1.3.2.4-1: Test sequence Step Procedure Message Sequence TP Verdict EUT-TS Message 1 The TS transmits periodic Cluster Beacons. <-- Cluster Beacon message - - 2 The TS transmits a Data Request message indicating: request_flags: 0x00 (No HARQ), request_t_interval: 0x13 (1 second), request_n_packets: 0xff (continuous), request_n_bytes: 0x000a (10-byte data payload). <-- TMC: Data Request - - 3a The EUT transmits a Data Request Response message. --> TMC: Data Request Response - - 3b The TS transmits a packet as a random-access response. <-- - - - - EXCEPTION: The steps 4 to 7 are repeated for 10 times. - - - - 4 The TS transmits an interference signal according to field "Type 1" in Table 8.1.3.2.3-1. - - - - 5 Check: Does the EUT transmit a packet (containing Data Request Response message) within 2 seconds? --> TMC: Data Request Response 1 F 6 The TS stops transmitting interference. - - - - 7a Check: Does the EUT transmit a Data Request Response message within 1 second after removing the interference in step 6? --> TMC: Data Request Response 1 P 7b The TS transmits a packet as a random-access response. <-- - - - NOTE: The interference power level is measured from the EUT transmission bandwidth at the EUT input. |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.3 Random Access Data Transmission | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.3.1 Test Purpose | Table 8.1.3.3.1-1: Test Purpose to sequence mapping Test Name Reference TP Random access transmission length 7.1.3.1.3 1 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.3.2 Test Applicability | This test is applicable according to the following PICS parameters. ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 63 Table 8.1.3.3.2-1: PICS selection parameters PICS Selection Description Status pc_mac_pt PT mode m pc_mac_rach_tx Support Random Access Transmission m |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.3.3 Pre-Test conditions | Prerequisite tests: • Transmission on random-access resources • Association Request and Release Test System: • Configuration: CF03 EUT: • Mode: PT Preamble: • EUT in PT mode associated to another RD, according to Table 8.4.3.2-1 • Test mode on |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.3.4 Test Procedure Sequence | Table 8.1.3.3.4-1: Test values for Max RACH Length Profile Max_RACH_Length Core 2, 4, 8, 12 (Slots) ETSI TS 103 874-2 [7] As defined in ETSI TS 103 874-2 [7], Table 7.3.4.3.4-1 Table 8.1.3.3.4-2: Test sequence Step Procedure Message Sequence TP Verdict EUT-TS Message 1 The TS transmits a Cluster Beacon indicating Max_RACH_Length as defined in Table 8.1.3.3.1-1. <-- Cluster Beacon message - - 2 The TS transmits a Data Request message indicating: request_flags: 0x80 (HARQ), request_t_interval: 0x13 (1 second), request_n_packets: 0x01 (1 packet), request_n_bytes: 0xffff (Maximum data payload size supported by the EUT). <-- TMC: Data Request - - 3a The EUT transmits a Data Request Response message. --> TMC: Data Request Response - - 3b The TS transmits a packet as a random-access response. <-- - - - 4 Check: Does the EUT transmit a packet indicating "Packet Length" less or equal to the "Max RACH Length" in step 3a? (see note) - - 1 P NOTE: The EUT may refrain from transmitting if it cannot fit any packet to the RACH resources. ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 64 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.4a Random Access Reception and Response (Announced in beacon message) | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.4a.1 Test Purpose | Table 8.1.3.4a.1-1: Test Purpose to sequence mapping Test Name Reference TP Reception from random-access resources announced in beacon message and response 7.1.3.2.1a 1 Reception of other packets 7.1.3.2.2 2 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.4a.2 Test Applicability | This test is applicable according to the following PICS parameters. Table 8.1.3.4a.2-1: PICS selection parameters PICS Selection Description Status pc_mac_ft FT mode m pc_mac_rach_res_bea Support Random Access Resource announcement in beacon messages m |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.4a.3 Pre-Test conditions | Prerequisite tests: • Beaconing Transmission Test System: • Configuration: CF02 EUT: • Mode: FT Preamble: • EUT is switched on • EUT is commanded to transmit Cluster Beacon(s). |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.4a.4 Test Procedure Sequence | Table 8.1.3.4a.4-1: Test sequence Step Procedure Message Sequence TP Verdict EUT-TS Message 1 The EUT transmits a Cluster Beacon message. --> Cluster Beacon message - - 2 The TS transmits a packet on the random-access resources of the EUT. <-- MAC PDU - - 3 Check: Does the EUT transmit a random-access response within the RACH response window? --> RACH response 1 P 4 The TS transmits a packet indicating a different "Receiver Identity" from the EUT. <-- MAC PDU - - 5 Check: Does the EUT transmit a random-access response? --> RACH response 2 F 6 The TS transmits a packet indicating a different "Short Network Address" from the EUT. <-- MAC PDU - - 7 Check: Does the EUT transmit a random-access response? --> RACH response 2 F ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 65 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.4b Random Access Reception and Response (Announced in unicast message) | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.4b.1 Test Purpose | Table 8.1.3.4b.1-1: Test Purpose to sequence mapping Test Name Reference TP Reception from random-access resources announced in unicast message and response 7.1.3.2.1b 1 Reception of other packets 7.1.3.2.2 2 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.4b.2 Test Applicability | This test is applicable according to the following PICS parameters. Table 8.1.3.4b.2-1: PICS selection parameters PICS Selection Description Status pc_smcb Smart Metering, City and Buildings m pc_mac_pt PT mode m pc_mac_rach_res_uni Support Random Access Resource announcement by unicast signalling m |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.4b.3 Pre-Test conditions | Prerequisite tests: • Transmission on random-access resources • Association Request and Release Test System: • Configuration: CF03 EUT: • Mode: PT Preamble: • EUT in PT mode associated to another RD, according to Table 8.4.3.2-1 • EUT has signalled Random Access Resource IE within a unicast message ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 66 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.3.4b.4 Test Procedure Sequence | Table 8.1.3.4b.4-1: Test sequence Step Procedure Message Sequence TP Verdict EUT-TS Message 1 The TS transmits a packet on the random-access resources of the EUT. <-- MAC PDU - - 2 Check: Does the EUT transmit a random-access response within the RACH response window? --> RACH response 1 P 3 The TS transmits a packet indicating a different "Receiver Identity" from the EUT. <-- MAC PDU - - 4 Check: Does the EUT transmit a random-access response? --> RACH response 2 F 5 The TS transmits a packet indicating a different "Short Network Address" from the EUT. <-- MAC PDU - - 6 Check: Does the EUT transmit a random-access response? --> RACH response 2 F |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.4 Scheduled Access data transfer | Void. |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.5 HARQ Procedures | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.5.1 HARQ Transmission | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.5.1.1 Test Purpose | Table 8.1.5.1.1-1: Test Purpose to sequence mapping Test Name Reference TP Successful HARQ transmission 7.1.5.1.1 1 Redundancy version reset 7.1.5.1.2 2 Redundancy version increment 7.1.5.1.3 3 Max HARQ Re-Tx 7.1.5.1.4 4 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.5.1.2 Test Applicability | This test is applicable according to the following PICS parameters. Table 8.1.5.1.2-1: PICS selection parameters PICS Selection Description Status pc_mac_ft FT mode o.1 pc_mac_pt PT mode o.1 pc_mac_harq_tx Support HARQ transmission m o.1: At least one of the features shall be supported. |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.5.1.3 Pre-Test conditions | Prerequisite tests: • Mode FT: - Beaconing transmission - Transmission on Random Access Resources ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 67 - Random Access Reception - Association Response and Release • Mode PT: - Transmission on Random Access Resources - Random Access Data Transmission - Association Request and Release Test System: • Configuration: CF02 when EUT in FT Mode • Configuration: CF03 when EUT in PT Mode EUT: • Mode: FT or PT Preamble: • Mode FT: - EUT in FT mode associated to another RD, according to Table 8.4.2.2-1 • Mode PT: - EUT in PT mode associated to another RD, according to Table 8.4.3.2-1 • Test Mode on |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.5.1.4 Test Procedure Sequence | Table 8.1.5.1.4-1: Test sequence Step Procedure Message Sequence TP Verdict EUT-TS Message - EXCEPTION: The steps 1a to 1b depend on the test parameters on whether the EUT operates in FT or PT mode. - - - - 1a IF EUT Mode = FT THEN the EUT transmits periodic Cluster Beacon messages. --> Cluster Beacon message - - 1b IF EUT Mode = PT THEN the TS transmits periodic Cluster Beacon messages. <-- Cluster Beacon message - - 2 The TS transmits a Data Request message indicating: request_flags: 0x80 (HARQ enabled), request_t_interval: 0x13 (1 second), request_n_packets: 0xff (continuous), request_n_bytes: 0x000a (10-byte data payload). <-- TMC: Data Request - - 3 The EUT transmits a packet containing PHY Header Type 2, indicating Header Format: 0. --> TMC: Data Request Response - - 4 The TS transmits a packet containing Transmission Feedback indicating ACK to indicate successful reception of the packet from step 3. <-- HARQ ACK - - 5 When: The EUT transmits a packet indicating the same HARQ process number as in step 3. (see note) --> TMC: Data Request Response 1 P ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 68 Step Procedure Message Sequence TP Verdict EUT-TS Message 5a Check: Does the packet transmitted in step 5 indicate "DF Redundancy Version": 0? - - 1 P 5b Check: Does the packet transmitted in step 5 indicate toggled "DF New Data Indication" compared to step 3. - - 1 P 6 The TS transmits a packet containing Transmission Feedback indicating ACK to indicate successful reception of the packet from step 5. <-- HARQ ACK - - 7 The EUT transmits a packet containing PHY Header Type 2, indicating Header Format: 0. --> TMC: Data Request Response - - 8 The TS transmits a packet containing Transmission Feedback indicating NACK to indicate unsuccessful reception of the packet from step 7, and requesting redundancy version reset to 0. (Feedback info format 6) <-- HARQ NACK - - 9 When: The EUT transmits a packet indicating the same HARQ process number as in step 7, and before timer Max HARQ Re-Tx expires. (see note) --> TMC: Data Request Response 2 P 9a Check: Does the packet transmitted in step 9 indicate "DF Redundancy Version": 0? - - 2 P 9b Check: Does the packet transmitted in step 9 indicate the same "DF New Data Indication" as in the packet in step 7? - - 2 P 10 The TS transmits a packet containing Transmission Feedback indicating ACK to indicate successful reception of the packet from step 9. <-- HARQ ACK - - 11 The EUT transmits a packet containing PHY Header Type 2, indicating Header Format: 0. --> TMC: Data Request Response - - 12 The TS transmits a packet containing Transmission Feedback indicating NACK to indicate unsuccessful reception of the packet from step 11. <-- HARQ NACK - - - EXCEPTION: Steps 13 to 14 are repeated until timer Max HARQ Re-Tx expires for the MAC PDU transmitted at step 11. - - - - 13 When: The EUT transmits a packet indicating the same HARQ process number as in step 11, and before timer Max HARQ Re-Tx expires. (see note) --> TMC: Data Request Response 3 P 13a Check: Does the packet transmitted in step 13 indicate the next "DF Redundancy Version"? - 3 P 13b Check: Does the packet transmitted in step 13 indicate the same "DF New Data Indication" as in the packet in step 11? - 3 P 14 The TS transmits a packet containing Transmission Feedback indicating NACK to indicate incorrect reception of the packet from step 13. <-- HARQ NACK - - 15 When: The EUT transmits a packet indicating the same HARQ process number as in step 11, and timer Max HARQ Re-Tx expires for the packet transmitted in step 11 (see note). --> TMC: Data Request Response 4 P 15a Check: Does the packet transmitted in step 15 indicate "DF Redundancy Version": 0? - - 4 P 15b Check: Does the packet transmitted in step 15 indicate toggled "DF New Data Indication" compared to step 11. - - 4 P 16 The TS transmits a packet containing Transmission Feedback indicating ACK to indicate successful reception of the packet from step 15. <-- HARQ ACK - - NOTE: The EUT is allowed to transmit packets indicating other HARQ process numbers in between. ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 69 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.5.2 HARQ Feedback | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.5.2.1 Test Purpose | Table 8.1.5.2.1-1: Test Purpose to sequence mapping Test Name Reference TP NACK Feedback 7.1.5.2.1 1 ACK Feedback 7.1.5.2.2 2 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.5.2.2 Test Applicability | This test is applicable according to the following PICS parameters. Table 8.1.5.2.2-1: PICS selection parameters PICS Selection Description Status pc_mac_ft FT mode o.1 pc_mac_pt PT mode o.1 pc_mac_harq_feedback Support HARQ feedback m o.1: At least one of the features shall be supported. |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.5.2.3 Pre-Test conditions | Prerequisite tests: • Mode FT: - Beaconing Transmission - Random Access Reception - Association Response and Release • Mode PT: - Random Access Reception - Association Request and Response Test System: • Configuration: CF02 when EUT in FT Mode • Configuration: CF03 when EUT in PT Mode EUT: • Mode: FT or PT Preamble: • Mode FT: - EUT in FT mode associated to another RD, according to Table 8.4.2.2-1 • Mode PT: - EUT in PT mode associated to another RD, according to Table 8.4.3.2-1 • Test Mode on ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 70 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.5.2.4 Test Procedure Sequence | Table 8.1.5.2.4-1: Test Sequence Step Procedure Message Sequence TP Verdict EUT-TS Message - EXCEPTION: Steps 1 to 4 are repeated for each HARQ process. - - - - 1 The TS transmits a packet using Physical Layer Control Field Type 2 indicating "Header Format": 000, such that the EUT cannot successfully decode the PDC. <-- MAC PDU - - 2 Check: Does the EUT transmit a packet containing Transmission Feedback indicating NACK, after the total HARQ feedback delay and before delay Max HARQ Re-Tx after step 1, to indicate unsuccessful reception of the packet transmitted in step 1? --> HARQ NACK 1 P - EXCEPTION: Step 3 shall be repeated until HARQ ACK is received at step 4 or until timer "Max HARQ Re-Tx" expires for the MAC PDU. - - - - 3 The TS re-transmits the packet from step 1, such that the EUT can successfully decode the PDC. <-- MAC PDU - - - EXCEPTION: HARQ NACKs from the EUT are allowed at step 4. - - - - 4 Check: Does the EUT transmit a packet containing Transmission Feedback indicating ACK, after the total HARQ feedback delay and before delay Max HARQ Re-Tx after step 3, to indicate successful reception of the packet transmitted in step 3? --> HARQ ACK 2 P |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.6 Multiplexing and Assembly | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.6.1 MAC IE Multiplexing | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.6.1.1 Test Purpose | Table 8.1.6.1.1-1: Test Purpose to sequence mapping Test Name Reference TP MAC PDU Multiplexing 7.1.6.1 1 Padding IE 7.1.6.2 2 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.6.1.2 Test Applicability | This test is applicable according to the following PICS parameters. Table 8.1.6.1.2-1: PICS selection parameters PICS Selection Description Status pc_mac_ft FT mode o.1 pc_mac_pt PT mode o.1 pc_mac_muxa Support MAC PDU multiplexing and assembly m o.1: At least one of the features shall be supported. ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 71 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.6.1.3 Pre-Test Conditions | Prerequisite tests: • None Test System: • Configuration: CF02 when EUT in FT Mode • Configuration: CF03 when EUT in PT Mode EUT: • Mode: FT or PT Preamble: • Mode FT: - EUT in FT mode associated to another RD, according to Table 8.4.2.2-1 • Mode PT: - EUT in PT mode associated to another RD, according to Table 8.4.3.2-1 PIXIT parameters: Table 8.1.6.1.3-1: PIXIT parameters PIXIT parameter Description Status px_max_app_packet_bytes Maximum application data payload size supported by the EUT m |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.6.1.4 Test Procedure Sequence | Table 8.1.6.1.4-1: Test Sequence Step Procedure Message Sequence TP Verdict EUT-TS Message - EXCEPTION: Repeat steps 1 to 4 for different values of S = 20, 40, 80, 120, but where 0 < S ≤ px_max_app_packet_bytes. - - - - 1 The TS transmits a Data Request message indicating: request_flags: 0x80 (HARQ), request_t_interval: 0x00 (As soon as possible), request_n_packets: 0x01 (1 packet), request_n_bytes: S. <-- TMC: Data Request - - 2 The EUT transmits a packet containing Data Request Response. --> TMC: Data Request Response - - 3 Check: Does the MAC PDU transmitted in step 2 contain full and correctly multiplexed IEs? - - 1 P 4 Check: Does the MAC PDU transmitted in step 2 contain a Padding IE which does not increase the TBS length for the used configuration (see note). - - 2 P NOTE: The Padding IE may be excluded if a valid MAC PDU size is otherwise reached. ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 72 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.7 Mobility Procedures | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.7.1 PT initiated mobility | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.7.1.1 Test Purpose | Table 8.1.7.1.1-1: Test Purpose to sequence mapping Test Name Reference TP Mobility by more suitable RSSI-2 7.1.7.1 1 Validity of Association Release message 7.1.8.3.1 2 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.7.1.2 Test Applicability | This test is applicable according to the following PICS parameters. Table 8.1.7.1.2-1: PICS selection parameters PICS Selection Description Status pc_mac_pt PT mode m pc_mac_mob Support mobility procedures m |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.7.1.3 Pre-Test conditions | Clause 5.7 Mobility Procedures as defined in ETSI TS 103 636-4 [4] does not impose mandatory requirements for the RD but provides recommendations on how implementation should behave. Therefore, supporting test descriptions defined in this clause and test purposes defined in clause 7.1.7 are optional. Prerequisite tests: • Selecting RD for association • Transmission on Random Access Resources • Association Request and Release Test System: • Configuration: CF05 • The link quality between the EUT and FT1 shall be near the sensitivity level • FT1 and FT2 use equal power levels for transmitting beacons • FT1 and FT2 broadcast the same cost value in the Cluster Beacon message • FT1 and FT2 operate on the same physical channel EUT: • Mode: PT Preamble: • The EUT is switched on ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 73 PIXIT parameters: Table 8.1.7.1.3-1: PIXIT parameters PIXIT parameter Description Status px_beacon_scan_period Time period at which the EUT scans for beacons m px_min_sensitivity_level RD sensitivity level m c.1: IF pc_mac_bea_network_tx THEN m ELSE n/a. |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.7.1.4 Test Procedure Sequence | Table 8.1.7.1.4-1: Test System RSSI-2 configuration Type LT RSSI-2 level of beacon transmissions at EUT input (dBm) T1 FT1 px_min_sensitivity_level + MIN_QUALITY + 10 dB + PowerMargin FT2 px_min_sensitivity_level + MIN_QUALITY T2 FT1 px_min_sensitivity_level + MIN_QUALITY FT2 px_min_sensitivity_level + MIN_QUALITY + RELATIVE_QUALITY + PowerMargin PowerMargin as defined in Table 8.1.1.4.2-1. NOTE 1: RELATIVE_QUALITY is signalled in the Cluster Beacon IE. NOTE 2: When setting the PowerMargin the TS should consider its own transmission output power tolerance to ensure the correct power level at the input of the EUT. Table 8.1.7.1.4-2: Test sequence Step Procedure Message Sequence TP Verdict EUT-TS Message 1 The test system path losses are adjusted such that the RSSI-2 level at the EUT input is according to row "T1" in Table 8.1.7.1.4-1. - - - - 2 The TS (FT1) transmits periodic Cluster beacon message, indicating CountToTrigger value. <-- Cluster Beacon message - - 3 The EUT transmits an Association Request message to the TS (FT1). --> Association Request message - - 4 The TS (FT1) transmits an Association Response message indicating ACK. <-- Association Response message - - 5 The TS (FT2) transmits periodic Cluster beacon messages. <-- Cluster Beacon message - - 6 Wait px_beacon_scan_period * CountToTrigger seconds. - - - - 7 Check: Does the EUT transmit an Association Request message to FT2. --> Association Request message 1 F 8 The test system path losses are adjusted such that the RSSI-2 level at the EUT input is according to row "T2" in Table 8.1.7.1.4-1. - - - - 9 Wait pc_mac_mob_beacon_scan_period * CountToTrigger seconds. - - - - - EXCEPTION: The step sequences (10a1 to 10a2) and (10b1 to 10b2) can occur in any order. The "lower case" letter identifies sequence steps that are always performed in order. - - - - 10a1 Check: Does the EUT transmit an Association Request message to FT2. --> Association Request message 1 P 10a2 The TS (FT2) transmits an Association Response message. <-- Association Response message - - 10b1 Check: Does the EUT transmit an Association Release message to FT1. --> Association Release message 1 - 10b2 Check: Does the EUT transmit a valid Association Release message in step 10b1. - - 2 P ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 74 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.8 Association Procedure | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.8.1 Association Response and Release | |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.8.1.1 Test Purpose | Table 8.1.8.1.1-1: Test Purpose to sequence mapping Test Name Reference TP Association Response 7.1.8.1.2 1 Validity of Association Response message 7.1.8.1.1 2 Association Release 7.1.8.3.2 3 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.8.1.2 Test Applicability | This test is applicable according to the following PICS parameters. Table 8.1.8.1.2-1: PICS selection parameters PICS Selection Description Status pc_mac_ft FT mode m pc_mac_ass_ft Support FT mode association procedures m |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.8.1.3 Pre-Test conditions | Prerequisite tests: • Beaconing Transmission • Random Access Reception Test System: • Configuration: CF02 EUT: • Mode: FT Preamble: • EUT is transmitting Cluster Beacon(s). • Test mode on PICS parameters: Table 8.1.8.1.3-1: Additional PICS parameters PICS parameter Description Status pc_mac_sec Support MAC Security procedures o pc_smcb Smart Metering, City and Buildings o ETSI ETSI TS 104 047-2 V1.1.1 (2025-10) 75 |
8e90692f70e1e9a0f58f164e7ad90f06 | 104 047-2 | 8.1.8.1.4 Test Procedure Sequence | Table 8.1.8.1.4-1: Test sequence Step Procedure Message Sequence TP Verdict EUT-TS Message 1 The TS transmits an Association Request message. <-- Association Request - - 2a Check: Does the EUT transmit an Association Response message as a random-access response within the RACH response window? --> Association Response 1 P 2b Check: Does the EUT transmit a valid Association Response message in step 2a? - - 2 P - EXCEPTION: Steps 3 to 6 are executed based on the Association Response message feedback transmitted in step 2. - - - - 3 IF the Association Response message in step 2a indicates ACK, THEN the TS transmits a Data Request message indicating: request_flags: 0x80 (HARQ), request_t_interval: 0x14 (2 seconds), request_n_packets: 0xff (continuous), request_n_bytes: 0x000a (10-byte data payload). <-- TMC: Data Request - - 4 Check: Does the EUT transmit a Data Request Response message? --> TMC: Data Request Response - P 5 The TS transmits an Association Release message 1 second after step 4. <-- Association Release message - - 6 Check: Does the EUT transmit a packet within 2 seconds after the reception of the Association Release message? --> DLC PDU 3 F |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.