hash stringlengths 32 32 | doc_id stringlengths 7 13 | section stringlengths 3 121 | content stringlengths 0 2.2M |
|---|---|---|---|
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 6.2 Transmitter power | |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 6.2.1 Maximum output power | The maximum output power is defined as the mean power of the transmitted packet. The maximum transmitter output power for Radio Device is defined in table 6.2.1-1. Table 6.2.1-1: Maximum output power RD power class Operating channel bandwidth (MHz) 1,728 3,456 6,912 Output power (dBm) Class I 23 23 23 Class II 21 21 21... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 6.3 Transmitter power control | |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 6.3.1 Absolute power tolerance | Absolute power tolerance is the ability of the radio device transmitter to set output power to a specific value. Packet transmission power is signalled in Physical Layer Control Field ETSI TS 103 636-4 [3], clause 6.2. Transmission power shall be measured as an average over the active period of the transmitted packet. ... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 6.3.2 Void | |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 6.3.3 Minimum output power | The minimum controlled output power of the radio device is defined as the power in the channel bandwidth, when the power is set to a minimum value. Transmission power tolerance is defined in clause 6.3.1, table 6.3.1-1. Table 6.3.3-1: Minimum output power Parameter/Unit Channel bandwidth (MHz) 1,728 3,456 6,912 Minimum... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 6.3.4 Transmit OFF power | Transmit OFF power is defined as the mean power when the transmitter is OFF. The transmitter is OFF when the radio device is not allowed to transmit or during periods when it is not transmitting in the radio frame. During active HARQ process the radio device is not considered to be OFF. The transmit OFF power is define... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 6.3.5 Transmit ON/OFF time mask | The transmit ON/OFF time mask defines the observation period between Transmit OFF and ON power and between Transmit ON and OFF power. The subslot duration is defined in ETSI TS 103 636-3 [2], clause 4.4. The OFF-power measurement period is defined in a duration of at least one slot before and after the transmission exc... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 6.4 Transmit signal quality | |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 6.4.1 Frequency error | RD modulated transmitter carrier frequency accuracy observed over the transmitted packet shall be within ±10,0 ppm compared to the selected absolute carrier centre frequency as specified in clause 5.4.2. |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 6.4.2 Transmit modulation quality | The Error Vector Magnitude (EVM) is a measure of the difference between the reference waveform and the measured waveform. The EVM result is defined after the receiver FFT as the square root of the ratio of the mean error vector power to the mean reference power expressed as a percentage. The EVM is measured over all oc... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 6.5 Transmitter spectrum emission requirements | |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 6.5.1 General | Radio equipment transmitter spectrum emissions are occupied channel emissions, out of band and spurious emissions. The relation of these emission components is illustrated in figure 6.5.1-1. ETSI ETSI TS 103 636-2 V2.1.1 (2024-10) 16 Release 2 Channel bandwidth ∆fOoB ∆fOoB Operating band Spurious domain Spurious domain... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 6.5.2 Occupied channel BW | Occupied bandwidth is a measure of the bandwidth containing 99 % of the total integrated mean power of the transmitted spectrum on the assigned channel. The occupied bandwidth shall be less than the nominal channel bandwidth as defined in table 5.3.2-1. |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 6.5.3 Out of band emissions | The Out of band emissions are unwanted emissions immediately outside the assigned channel bandwidth resulting from the modulation process and non-linearity in the transmitter but excluding spurious emissions. The spectrum emission mask of the RD applies to frequencies Δ starting from the ± edge (from + /2 or f... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 6.5.4 Spurious emissions | Spurious emissions are emissions which are caused by unwanted transmitter effects such as harmonics emission, parasitic emissions, intermodulation products and frequency conversion products, but exclude out of band emissions unless otherwise stated. The spurious emission limits are specified in terms of general require... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 6.5.5 Adjacent Channel Leakage Ratio | Adjacent Channel Leakage Ratio (ACLR) is used as a measure of the amount of transmission power leaking into adjacent channels. ACLR is the ratio of the filtered mean power centered on the assigned channel frequency to the filtered mean power centered on an adjacent channel frequency with measurement bandwidth equal to ... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 7 Receiver characteristics | |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 7.1 General | Receiver characteristics are specified at the antenna connector(s) of the Radio Equipment. For REs with an integral antenna only, a reference antenna(s) with a gain of 0 dBi is assumed for each antenna port(s). RD with an integral antenna(s) can convert power levels into field strength requirements by assuming 0 dBi ga... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 7.2 Reference sensitivity | The reference sensitivity power level is the minimum mean power applied to RD antenna port. RD throughput shall meet or exceed the requirements for the specified reference measurement channel. The throughput shall be ≥ 90 % of the maximum throughput of the Fixed Reference Channel (FRC) measurement as specified in claus... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 7.3 Maximum input level | The maximum input rower is the mean power received at the RD antenna port, at which the throughput shall meet or exceed the minimum requirements for the specified reference measurement channel. The throughput shall be ≥ 90 % of the maximum throughput of the Fixed Reference Channel (FRC) measurement as specified in clau... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 7.4 Adjacent Channel Selectivity | Adjacent Channel Selectivity (ACS) is a measure of a receiver's ability to receive own signal assigned to a channel frequency in the presence of an adjacent channel signal interference at a given frequency offset from the centre frequency of the assigned channel. ACS is the ratio of the receive filter attenuation on th... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 7.5 Blocking characteristics | |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 7.5.1 General | The blocking characteristic is a measure of the receiver's ability to receive a wanted signal at its assigned channel frequency in the presence of an unwanted interferer on frequencies other than those of the spurious response or the adjacent channels, without this unwanted input signal causing a degradation of the per... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 7.5.2 In band blocking characteristics | In-band blocking is defined for an unwanted interfering signal falling into the RD operating band or into the first adjacent channel below or above the RD receive band at which the relative throughput shall meet or exceed the minimum requirement for the specified measurement channels. The test parameters are defined in... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 7.5.3 Out of band blocking characteristics | Out-of-band band blocking is defined for an unwanted CW interfering signal falling more than 15 MHz below or above the RD receive band. Out of band blocking test parameters are defined in tables 7.5.3-1, 7.5.3-2 and 7.5.3-3 for respective operating channel bandwidth. Blocker signal step size is 1 MHz. The throughput sh... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 7.6 Spurious response | Spurious response is a measure of the receiver's ability to receive a wanted signal on its assigned channel frequency without exceeding a given degradation due to the presence of an unwanted CW interfering signal at any other frequency at which a response is obtained i.e. for which the out of band blocking limit as spe... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 7.7 Spurious emissions | The spurious emissions power is the power of emissions generated or amplified in a receiver that appear at the RD antenna connector. The power of any narrow band CW spurious emission shall not exceed the maximum level specified in table 7.7-1. The spurious emissions shall be measured during the time period where the re... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 7.8 Receiver intermodulation | Intermodulation response rejection is a measure of the capability of the receiver to receive a wanted signal on its assigned channel frequency in the presence of two or more interfering signals which have a specific frequency relationship to the wanted signal. The RD shall fulfil the minimum requirement specified in ta... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 8 Radio Device measurements | |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 8.1 General | This clause defines the measurement requirements for Radio Device (RD) in terms how they are measured and measurement times, the dynamic range and accuracy requirements. Unless otherwise noted, the reference point for these measurements is antenna port(s). |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 8.2 Received signal strength (RSSI-1) measurement | |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 8.2.1 General | RSSI-1 measurement is intended to assess the channel use. The RSSI-1 measurement is a linear average of received power observed during 1 OFDM symbol with a Measurement BandWidth of transmission channel bandwidth defined in table 5.3.2-1. Individual RSSI-1PACKET(n) measurements from packet n can be averaged over multipl... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 8.2.2 Measurement accuracy and dynamic range | The reported measurement accuracy shall be within the limits stated in the table 8.2.2-1 in 95 % of the reported values. Table 8.2.2-1: RSSI-1 power measurement requirement RSSI-1 measurement requirement RSSI-1 measured power/dBm Accuracy in normal conditions RXsensitivity < RSSI-1 ≤ (RXsensitivity + 10 dB) ±5,5 dB (RX... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 8.2.3 RSSI-1 measurement report mapping | The RD shall use the measurement results signalling mapping defined in the table 8.2.3-1. ETSI ETSI TS 103 636-2 V2.1.1 (2024-10) 23 Release 2 Table 8.2.3-1: RSSI-1 measurement report mapping Reported value Reported value (dBm) Measured Value (dBm) 0xFF -1 -1,5 < x 0xFE -2 -1,5 ≤ x < -2,5 0xFD -3 -2,5 ≤ x < -3,5 … … … ... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 8.3 Demodulated signal strength (RSSI-2) measurement | |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 8.3.1 General | The RSSI-2 signal strength measurement is intended to measure signal strength of detected and demodulated DECT-2020 packet and shall be mapped to respective transmitter and network ID. Individual RSSI-2PACKET(n) measurements from packet (n) can be averaged over multiple received packets with a leaky integrator RSSI_2(n... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 8.3.2 Measurement accuracy and dynamic range | The reported measurement accuracy shall be within the limits stated in table 8.3.2-1 in 95 % of the reported values. Table 8.3.2-1: RSSI-2 power measurement requirement RSSI-2 measurement requirement RSSI-2 measured power/dBm Accuracy in normal conditions RXsensitivity < RSSI-2 ≤ (RXsensitivity + 10 dB) ±4 dB (RXsensit... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 8.3.3 RSSI-2 measurement report mapping | The RD shall use the measurement results signalling mapping defined in table 8.3.3-1. ETSI ETSI TS 103 636-2 V2.1.1 (2024-10) 24 Release 2 Table 8.3.3-1: RSSI-2 measurement report mapping Reported value Reported value (dBm) Measured value (dBm) 0xFF -1 -1,5 < x 0xFE -2 -1,5 ≤ x < -2,5 0xFD -3 -2,5 ≤ x < -3,5 … … … 0x74... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 8.4 Demodulated Signal to Noise quality value (SNR) | |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 8.4.1 General | The received signal to noise quality is intended to measure radio device signal quality from detected and demodulated DECT-2020 packet and shall be mapped to respective transmitter and network ID. Individual SNRPACKET(n) measurements from packet n can be averaged over multiple received packets with a leaky integrator S... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 8.4.2 Measurement accuracy and dynamic range | The reported measurement accuracy shall be within the limits in table 8.4.2-1 in 95 % of the reported values. Table 8.4.2-1: SNR measurement requirement SNR measurement requirement SNR range Accuracy 5 dB < SNR ≤ 25 dB ±3 dB |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 8.4.3 Demodulated signal to noise quality measurement report mapping | The RD shall use the measurement results signalling mapping defined in table 8.4.3-1. ETSI ETSI TS 103 636-2 V2.1.1 (2024-10) 25 Release 2 Table 8.4.3-1: Demodulated signal to noise quality measurement report mapping Reported value Reported value (dB) Measured value (dB) 0x7F 63,5 63,25 ≤ x 0x7E 63,0 62,75 ≤ x < 63,25 ... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 9 Radio channel decoding performance | |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 9.1 Introduction | This clause defines the minimum performance requirements for the physical channels specified in ETSI TS 103 636-3 [2]. The minimum RD performance requirements in this clause are specified by using the measurement channels and propagation conditions specified in annex A. These measurement channels are based on symmetric... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 9.2 Fixed Reference Channel performance | |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 9.2.1 Fixed Reference Channel with QPSK | Common test parameters QPSK Fixed Reference Channel are defined in clause A.2.1 for 1,728 MHz operating channel bandwidth, clause A.3.1 for 3,456 MHz operating channel bandwidth and clause A.4.1 for 6,912 MHz operating channel bandwidth operation. The reference maximum throughput performance is defined as average bitra... |
80d37856088f63e7d750d5ebb6f8499b | 103 636-2 | 9.2.2 Single receiver requirements | The requirement for the receiver's throughput performance is defined to be at least 90 % of the maximum throughput averaged over one radio frame for Fixed Refence Channel (FRC), as defined in clause 9.2.1. ETSI ETSI TS 103 636-2 V2.1.1 (2024-10) 26 Release 2 Table 9.2.2-1: Single receiver minimum throughput requirement... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 1 Scope | The scope of the present document is to define the radio reconfiguration related architecture for reconfigurable Radio Equipment. The work is based on the system requirements defined in ETSI TS 103 641 [1] and the Use Cases defined in ETSI TR 103 062 [i.1], ETSI TR 102 944 [i.2] and ETSI TR 103 585 [i.3]. |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 2 References | |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 2.1 Normative references | References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which a... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 2.2 Informative references | References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks i... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 3 Definition of terms, symbols and abbreviations | |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 3.1 Terms | For the purposes of the present document, the following terms apply: Baseband Parameter Aggregation (BPA): unit collecting all the context information to be transferred to the monitor NOTE: The BPA unit converts the context information into metric(s) such that a minimum bandwidth is consumed during the procedure of tra... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 3.2 Symbols | For the purposes of the present document, the following symbols apply: M1 Number of SFBs implemented on Radio computer M2 Number of SFBs implemented on hardware accelerators |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 3.3 Abbreviations | For the purposes of the present document, the following abbreviations apply: AOT Ahead-Of-Time ETSI ETSI TS 103 648 V1.1.1 (2020-01) 10 API Application Programming Interface ASF Administrator Security Function ASIC Applications-Specific Integrated Circuit BBU BaseBand Unit BE Back End BPA Baseband Parameter Aggregation... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.1 Introduction | The present deliverable describes those elements of a Radio Equipment which is related to the software radio reconfiguration only. For this reason, the usage of the term "architecture" is limited to those elements and not to the overall HW/SW architecture of a Radio Equipment which is out of the scope of the present do... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.2.1 High level description | Figure 4.2.1-1 shows the reconfigurable Radio Equipment architectural components related to the radio reconfiguration as well as the related entities. The main difference between the mobile device architecture [i.4] and the generalized Radio Equipment architecture defined in the present document is that a mobile device... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.2.2 Communication Services Layer (CSL) | The CSL is a layer related to communication services providing multiradio and non-radio functionalities. The typical examples of communication services related to multiradio functionalities are management for activating corresponding radio application or controlling data flows for each radio application. The typical ex... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.2.3 Radio Control Framework (RCF) | The RCF provides a generic environment for the execution of URA, and a uniform way of accessing the functionality of the radio computer and individual RAs. RCF provides services to CSL via the generalized Multiradio Interface (gMURI). The RCF includes the following 5 entities for managing URA [i.2]: • Configuration Man... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.2.4 Unified Radio Application (URA) | As described in clause 4.2.3, the RCF, which represents functionalities provided by the radio computer, requires all RAs to be subject to a common reconfiguration, multiradio execution and resource sharing strategy framework (depending on the concerned RERC). Since all RAs exhibit a common behaviour from the reconfigur... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.2.5 Architectural Components System Requirements mapping | The logical entities above described are mapped to the system requirements described in [1] as shown in Table 4.2.5-1. ETSI ETSI TS 103 648 V1.1.1 (2020-01) 17 Table 4.2.5-1: Mapping of Architectural Components to the system requirements described in [1] Entity/Component/Unit System Requirements [1] Comments Administra... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.3.1 High level description | Figure 4.3.1-1 exemplifies a Reconfigurable RE architecture reference model for multiradio applications. As shown in the Figure, the reconfigurable RE architecture shall include at least one radio computer. Figure 4.3.1-1: Reconfigurable Radio Equipment (RE) architecture Reference Model for multiradio applications In t... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.3.2 Reference Model System Requirements mapping | The architecture reference model above described is mapped to the system requirements described in [1] as shown in Table 4.3.2-1. Table 4.3.2-1: Mapping of Reference Model to the system requirements described in [1] Entity/Component/Unit System Requirements [1] Comments Computational Resources (vendor specific) R-FUNC-... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.4 Reconfigurable Radio Equipment - radio computer | |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.4.1 High level description | The System Architecture for multiple radio computers is illustrated in Figure 4.4.1-1 and Figure 4.4.1-2 Some of the entities included in the figures below may be located externally (in the "Cloud") in order to off-load processing from the concerned Radio Equipment. As example, the Back End compiler in Figure 4.4.1-1 i... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.4.2 radio computer System Requirement Mapping | The radio computer above described is mapped to the system requirements described in [1] as shown in Table 4.4.2-1 Table 4.4.2-1: Mapping of radio computer to the system requirements described in [1] Entity/Component/Unit System Requirements [1] Comments radio computer Architecture R-FUNC-RER-04 R-FUNC-RER-10 R-FUNC-RE... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.5.1 Radio Virtual Machine basic principles | The RVM shall enable a RA to choose one among multiple available protection classes for code to be executed on the RVM as well as a protection class for the RF front-end. Depending on the combination of chosen RF & RVM protection classes, the required re-certification process of the software reconfigurable radio platfo... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.5.2 RVM System Requirement Mapping | The RVM above described is mapped to the system requirements described in ETSI TS 103 641 [1] as shown in Table 4.5.2-1. Table 4.5.2-1: Mapping of RVM to the system requirements described in ETSI TS 103 641 [1] Entity/Component/Unit System Requirements [1] Comments Radio Virtual Machine R-FUNC-RER-13 R-FUNC-RER-14 The ... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.6.1 Introduction | As already described in clause 4.3.2, RAs loaded into a Reconfigurable RE are called URAs. The procedure of distributing and executing RA codes consists of 3 steps: design time, installation time and run time. Figures 4.6.2-1, 4.6.2-2, 4.6.2-3, 4.6.2-4 and 4.6.2-5 illustrate these three steps for the case of platform-s... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.6.2 Distribution and Installation of RAP | In this clause, the procedure of distribution and installation of RA codes on the target reconfigurable REs is presented. During the design time, the RA codes provider will generate a Radio Application Package (RAP) that includes metadata (e.g. for pipeline configuration) and RA codes. Note that the RC codes are part o... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.6.3 Operational Structure of URA | In this clause the operational structure of URA in run time is presented. For simplicity, this clause assumes the case where the Radio Equipment has one radio computer. In the case of multiple radio computers, the same structure shown at each figure is repeated for each of the radio computers in a given Radio Equipment... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.6.4 URA System Requirement Mapping | The URA above described is mapped to the system requirements described in [1] as shown in Table 4.6.4-1. programmable resources of Radio Platform ETSI ETSI TS 103 648 V1.1.1 (2020-01) 29 Table 4.6.4-1: Mapping of URA to the system requirements described in [1] Entity/Component/Unit System Requirements [1] Comments Conf... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.7 Security architecture for reconfigurable Radio Equipment | |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.7.1 Description | The security architecture for reconfigurable Radio Equipment extends the architecture defined in clause 4.2 of the present document in order to ensure the security of the reconfigurable platform and of the digital assets. NOTE: The rationale for the selection of security component, and the description of the security f... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 4.7.2 Security Components System Requirements mapping | The logical entities above described are mapped to the system requirements described in clause 6.6 of [1] as shown in Table 4.7.2-1. Table 4.7.2-1: Mapping of Security Components to the system requirements described in [1] Entity/Component/Unit System Requirements [1] Comments Administrator Security Function (ASF) R-FU... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 5 Reference Points | |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 5.1 Introduction | Figure 5.1-1 illustrates the entire architecture of RE with all the reference points being specified between corresponding entities. For simplicity, this clause assumes that the Radio Equipment has only one radio computer. In the case of multiple radio computers, the structure of RCF, URA, and Radio Platform is repeate... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 5.3 Reference Points required for list checking of URA | Mobility Policy Manager Administrator CF2 Configuration Manager CF1c Figure 5.3-1: Illustration of reference points for obtaining the lists of URA Figure 5.3-1 illustrates the reference points CF1c and CF2, which are related to URA list checking. Reference Point CF1c is an interface between Administrator and CM, throug... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 5.3.1 Reference Points required for updating instance of URA | Administrator Configuration Manager CF1d Figure 5.3.1-1: Illustration of reference points for updating instance of URA Figure 5.3.1-1 illustrates the reference points CF1d, which is related to updating instance of URA. Reference Point CF1d is an interface between Administrator and CM, through which Administrator reques... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 5.3.2 Reference Points required for configuring URA parameters | Administrator Configuration Manager CF1e Figure 5.3.2-1: Illustration of reference points for configuring URA parameters Figure 5.3.2-1 illustrates the reference points CF1e, which is related to configuring URA parameters. Reference Point CF1e is an interface between Administrator and CM, through which Administrator re... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 5.9 Reference Points required for flexible data flow | CTRL1d Mobility Policy Manager Radio Connection manager Figure 5.9-1: Illustration of reference points for flexible data flow • Figure 5.9-1 illustrates reference point CTRL1d, which is related to the flexible data flow. • Reference Point CTRL1d is an interface between MPM and RCM, through which MPM requests RCM to mov... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 5.10 Reference Points required for data flow control | Networking Stack CTRL4 CTRL5 Flow Controller Unified Radio Application Figure 5.10-1: Illustration of reference points for data flow control Figure 5.10-1 illustrates reference point CTRL4 and CTRL5, which are related to the data flow control. Reference Point CTRL4 is an interface between FC and N/W stack, through whic... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 5.11 Reference Points required for synchronizing radio time | Multi Radio Controller CTRL6 Unified Radio Application Figure 5.11-1: Illustration of reference points for synchronizing radio time Figure 5.11-1 illustrates reference point CTRL6, which is related to the synchronizing radio time. Reference Point CTRL6 is an interface between MRC and URA, through which MRC requests URA... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 5.13 Reference points required for security functions | The Figures below illustrate the required reference points for each security functions. Figure 5.13-1: Illustration of reference points for protection of RE Configuration Policy, RAP, and other assets ETSI ETSI TS 103 648 V1.1.1 (2020-01) 40 Figure 5.13-2: Illustration of reference points for protection of configuratio... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 6 Reconfigurable RE high level operating procedures | |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 6.0 Introduction | In this clause, sequence diagrams are introduced which cover unicast, multicast and broadcast routing between CSL and Radio Computer(s). In order to differentiate these three types of identifiers, the following generic representation is used: RCx, where "x" indicates the transmission mode including unicast (x=U), multi... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 6.2 Procedures for list checking of URA | Figure 6.2-1 illustrates a signalling diagram related to the list checking of URA. ETSI ETSI TS 103 648 V1.1.1 (2020-01) 46 Administrator ListRAReq (RCx:ID) RAList (RCx:ID) alt RC1 Mobility Policy Manager Routing Entity Configuration Manager ListRAReq (RCx:ID) RAList (RCx:ID) ListRAReq (RCx:ID) RAList (RCx:ID) ListRARe... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 6.2.1 Procedures for updating instance of URA | Figure 6.2-2 illustrates a signalling diagram related to updating instance of URA. ETSI ETSI TS 103 648 V1.1.1 (2020-01) 47 Configuration Manager R 1 : Unified Radio Application Resource Manager Multiradio Controller Administrator UpdateRAReq (R1:ID,R2:ID,RCx:ID) DeInstantiateRA (R1:ID) Instantiated Routing Entity RC1 ... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 6.2.2 Procedures for configuring URA parameters | Figure 6.2-3 illustrates a signalling diagram related to configuring URA parameters. R1: Unified Radio Application ConfRAParamsReq (R1:ID,Params,RCx :ID ) alt RC1 Administrator Routing Entity Configuration Manager ConfRAParamsCnf (R1:ID,RCx :ID) ConfRAParamsFailCnf (R1:ID,RCx :ID,Reason) Instantiated Reconfigured ConfR... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 6.3 Procedures for activation/deactivation of URA | Figure 6.3-1 illustrates a signalling diagram related to the activation of an URA. R1: Unified Radio Application ActivateReq (R1:ID,RCx:ID) alt RC1 Mobility Policy Manager Routing Entity Radio Connection Manager Activate (R1:ID) ActivateReq (R1:ID,RCx:ID) ActivateCnf (R1:ID,RCx:ID) ActivateFailCnf (R1:ID,RCx:ID,Reason)... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 6.4 Procedures for transferring context information | Figure 6.4-1 illustrates a signalling diagram related to the transfer of context information. ETSI ETSI TS 103 648 V1.1.1 (2020-01) 52 Figure 6.4-1: Context information transfer The procedure can be summarized as follows: • Monitor transfers a ContextInformationReq signal including URA (R1) ID to RC in URA. • RC in URA... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 6.6 Procedures for radio environment measurements | Figure 6.6-1 illustrates a signalling diagram related to the radio environment measurements. Mobility Policy Manager Radio Connection Manager R1: Unified Radio Application StartStopRadio MeasurementsReq (R1:ID,RCx:ID,StartStop) Active StartStopRadio MeasurementsReq (R1:ID,StartStop) StartStopRadio MeasurementsCnf (R1:I... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 6.7 Procedure for reporting discovered peer equipment | Figure 6.7-1 illustrates a signalling diagram related to report discovered peer equipment. Mobility Policy Manager Radio Connection Manager E1:Peer Equipment R1: Unified Radio Application Association Feasibility Message(E1:ID) Information PeerEquipments (R1:ID, E1:ID,...) Active Report PeerEquipments Req(R1:ID) Routing... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 6.8 Procedure for flexible data flow | Figure 6.8-1 illustrates a signalling diagram related to the flexible data flow. ETSI ETSI TS 103 648 V1.1.1 (2020-01) 60 Mobility Policy Manager Radio Connection Manager R1: Unified Radio Application ChangeDataFlowReq (R1:ID,RCx:ID,A1:ID,F1:I D,Action,Param,...) alt Network Association Established Data Flow Establishe... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 6.9 Procedure for data flow control | Figure 6.9-1 illustrates a signalling diagram related to the data flow control. ETSI ETSI TS 103 648 V1.1.1 (2020-01) 61 Routing Entity Flow Controller ChangingDataFlowReq (R1:ID, RCx:ID, F1:ID, F2:ID) alt Networking Stack ChangingDataFlowCnf (R1:ID,RCx:ID, F1:ID,F2:ID) ChangingDataFlowFailCnf (R1:ID,RCx:ID, F1:ID,F2:I... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 6.10 Procedure for synchronizing radio time | Figure 6.10-1 illustrates a signalling diagram related to the synchronizing radio time. Multi Radio Controller R1,R2: Unified Radio Application Active SynchronizeTimeReq (R1:ID,R2:ID,t) alt Synchronize TimeCnf(R1:ID,t) Synchronize TimeCnf(R2:ID,t) Synchronize TimeCnf(R1:ID,t) Synchronize TimeFailCnf(R2:ID,t, Reason) Sy... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 6.11 Procedure for control of reconfigurable RF transceiver | Figure 6.11-1 illustrates a signalling diagram related to the spectrum control services. ETSI ETSI TS 103 648 V1.1.1 (2020-01) 64 R1: Unified Radio Application T1: RF Transceiver CentreFreq SetupReq (R1:ID,T1:ID,Param) CentreFreq SetupCnf (R1:ID,T1:ID,Param) CentreFreq SetupFailCnf (R1:ID,T1:ID,Reason) alt BWSetupReq (... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 6.13 Procedure for configuration enforcement | Configuration enforcement is introduced in [i.6], clause 10. Figure 6.13-1 illustrates the procedure for sending a remote control command by a remote controller. ETSI ETSI TS 103 648 V1.1.1 (2020-01) 74 Figure 6.13-1: Signalling diagram for sending a remote control command The procedure can be summarized as follows: • ... |
ad259cf2e9e952d1ac0109435a646a88 | 103 648 | 6.14 Procedures for long-term management | Long-term management is introduced in [i.6], clause 11. Figure 6.14-1 illustrates the transfer of authority between two RRS Configuration Authorities. ETSI ETSI TS 103 648 V1.1.1 (2020-01) 76 Figure 6.14-1: Signalling diagram for transferring authority between two RRS Configuration Authorities The procedure can be summ... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.