input stringclasses 1
value | instruction stringlengths 237 1.47k | output stringlengths 234 350 | category stringclasses 1
value | index stringlengths 1 5 |
|---|---|---|---|---|
[ToolName]ﾄﾙｸﾚﾝﾁ[/ToolName]
[Size]5㎜[/Size]
[ToolOther]11.5N･m[/ToolOther]
[WorkName]逆流れﾌﾚｰﾑｷｯﾄR組立⑧[/WorkName]
[WorkItem]1. にBRACKET BRACKET をWASHER BOLT で取付け[/WorkItem]
[WorkPoint]下面
BRACKET BRACKET と の端面を合わせる
BRACKET は下面､BRACKET は上面に取付け
上面
ｾｯﾄｽｸﾘｭｰ締め付け
ｾｯﾄｽｸﾘｭｰ締め付け
ﾌﾞﾗｹｯﾄ固定後導通確保の為ｾｯﾄｽｸﾘｭｰを締め付ける[/WorkPoint... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]11.5N･m±10%[/StdVal]
[Method]ﾄﾙｸﾚﾝﾁ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2300 | |
[ToolName]ｺﾝﾍﾞｯｸｽ[/ToolName]
[Size]2m[/Size]
[ToolOther][/ToolOther]
[WorkName]逆流れﾌﾚｰﾑｷｯﾄR組立⑨[/WorkName]
[WorkItem]1. FRAME にSUPPORT NUT NUT CABLE-SUPPORT を取付け[/WorkItem]
[WorkPoint]外面
下面
内面
･は止めﾈｼﾞの方向を示す
内面
SUPPORT はNUT NUT とｾｯﾄで使用
内面
下面
外面
上面
前面
上面[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/Inspectio... | [QualityItem]寸法確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]作業指示の寸法である事[/StdVal]
[Method]ｺﾝﾍﾞｯｸｽ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2301 | |
[ToolName]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/ToolName]
[Size]2㎜[/Size]
[ToolOther]150cN･m[/ToolOther]
[WorkName]逆流れﾌﾚｰﾑｷｯﾄR組立⑩[/WorkName]
[WorkItem]1. にBRACKET BRACKET をWASHER BOLT で取付け[/WorkItem]
[WorkPoint]下面
BRACKET BRACKET と の端面を合わせる
BRACKET は下面､BRACKET は上面に取付け
上面
ｾｯﾄｽｸﾘｭｰ締め付け
ｾｯﾄｽｸﾘｭｰ締め付け
ﾌﾞﾗｹｯﾄ固定後導通確保の為ｾｯﾄｽｸﾘｭｰを締め付ける[/WorkP... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]150cN･m±10%[/StdVal]
[Method]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2302 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ｼｬｯﾀｰ部配線-2[/WorkName]
[WorkItem]1. の配線を固定する[/WorkItem]
[WorkPoint]配管に沿わせ固定する[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]ｲﾝｼｭﾛｯｸ指示
･ｹｰﾌﾞﾙ同士を固定
･ﾀｲﾏｳﾝﾄに固定 又は板金に固定[/Words]
| [QualityItem]結束確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り結束出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2303 | |
[ToolName]ﾄﾙｸﾚﾝﾁ[/ToolName]
[Size]5㎜[/Size]
[ToolOther]11.5N･m[/ToolOther]
[WorkName]逆流れﾌﾚｰﾑｷｯﾄR組立⑩[/WorkName]
[WorkItem]1. にBRACKET BRACKET をWASHER BOLT で取付け[/WorkItem]
[WorkPoint]下面
BRACKET BRACKET と の端面を合わせる
BRACKET は下面､BRACKET は上面に取付け
上面
ｾｯﾄｽｸﾘｭｰ締め付け
ｾｯﾄｽｸﾘｭｰ締め付け
ﾌﾞﾗｹｯﾄ固定後導通確保の為ｾｯﾄｽｸﾘｭｰを締め付ける[/WorkPoint... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]11.5N･m±10%[/StdVal]
[Method]ﾄﾙｸﾚﾝﾁ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2304 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]1000㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]逆流れﾌﾚｰﾑｷｯﾄR組立⑪[/WorkName]
[WorkItem]1. をWASHER BOLT で取付け[/WorkItem]
[WorkPoint] と の端面を合わせる
と の端面を合わせる
㉗定盤側に外面を合わせて組立てる
内面側
ﾌﾞﾗｹｯﾄ固定後導通確保の為ｾｯﾄｽｸﾘｭｰを締め付ける
ｾｯﾄｽｸﾘｭｰ締め付け
ｾｯﾄｽｸﾘｭｰ締め付け
ｾｯﾄｽｸﾘｭｰ締め付け
ｾｯﾄｽｸﾘｭｰ締め付け[/WorkPoint]
[Tol... | [QualityItem]寸法確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示寸法各±0.5㎜[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2305 | |
[ToolName]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/ToolName]
[Size]2㎜[/Size]
[ToolOther]150cN･m[/ToolOther]
[WorkName]逆流れﾌﾚｰﾑｷｯﾄR組立⑪[/WorkName]
[WorkItem]1. をWASHER BOLT で取付け[/WorkItem]
[WorkPoint] と の端面を合わせる
と の端面を合わせる
㉗定盤側に外面を合わせて組立てる
内面側
ﾌﾞﾗｹｯﾄ固定後導通確保の為ｾｯﾄｽｸﾘｭｰを締め付ける
ｾｯﾄｽｸﾘｭｰ締め付け
ｾｯﾄｽｸﾘｭｰ締め付け
ｾｯﾄｽｸﾘｭｰ締め付け
ｾｯﾄｽｸﾘｭｰ締め付け[/WorkPo... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]150cN･m±10%[/StdVal]
[Method]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2306 | |
[ToolName]ﾄﾙｸﾚﾝﾁ[/ToolName]
[Size]5㎜[/Size]
[ToolOther]11.5N･m[/ToolOther]
[WorkName]逆流れﾌﾚｰﾑｷｯﾄR組立⑪[/WorkName]
[WorkItem]1. をWASHER BOLT で取付け[/WorkItem]
[WorkPoint] と の端面を合わせる
と の端面を合わせる
㉗定盤側に外面を合わせて組立てる
内面側
ﾌﾞﾗｹｯﾄ固定後導通確保の為ｾｯﾄｽｸﾘｭｰを締め付ける
ｾｯﾄｽｸﾘｭｰ締め付け
ｾｯﾄｽｸﾘｭｰ締め付け
ｾｯﾄｽｸﾘｭｰ締め付け
ｾｯﾄｽｸﾘｭｰ締め付け[/WorkPoint]... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]11.5N･m±10%[/StdVal]
[Method]ﾄﾙｸﾚﾝﾁ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2307 | |
[ToolName]ｺﾝﾍﾞｯｸｽ[/ToolName]
[Size]2m[/Size]
[ToolOther][/ToolOther]
[WorkName]逆ﾌﾚｰﾑｷｯﾄFRONT2組立[/WorkName]
[WorkItem]1. FRAME にSUPPORT NUT NUT CABLE-SUPPORT を取付け[/WorkItem]
[WorkPoint]SUPPORT はNUT NUT とｾｯﾄで使用[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]NUT N... | [QualityItem]寸法確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示寸法各±1㎜[/StdVal]
[Method]ｺﾝﾍﾞｯｸｽ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2308 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]300㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]ﾌﾚｰﾑｷｯﾄ(扉小)組立①[/WorkName]
[WorkItem]1. FRAME にSUPPORT ･NUT ･NUT を取付[/WorkItem]
[WorkPoint]風船色ﾅｯﾄｻｲｽﾞ
上側
内側[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]M6
M5
M4
M3
ﾅｯﾄ挿入面
×4[... | [QualityItem]寸法確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]作業指示の寸法である事[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2309 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]ﾌﾚｰﾑｷｯﾄ(扉小)組立②[/WorkName]
[WorkItem]1. FRAME にSUPPORT ･NUT を取付[/WorkItem]
[WorkPoint]内側
右側
風船色ﾅｯﾄｻｲｽﾞ[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]×2
ﾅｯﾄ挿入面
M6
M5
M4
M3[/Word... | [QualityItem]寸法確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]作業指示の寸法である事[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2310 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ﾌﾚｰﾑｷｯﾄ(扉小)組立③[/WorkName]
[WorkItem]1. PANEL にPACKING を取付[/WorkItem]
[WorkPoint]取っ手取付用穴
PACKING の折り返しの長い方を内側面に取付[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]内側面
L=216
L=590
L=216
L=5... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2311 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ﾌﾚｰﾑｷｯﾄ(扉小)組立④[/WorkName]
[WorkItem]1. に ･ ･FRAME ･FRAME をBLOCK で取付[/WorkItem]
[WorkPoint]取っ手取付用穴
4角を付属のﾋﾞｽにて締結[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]内側面[/Words]
| [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2312 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ﾌﾚｰﾑｷｯﾄ(扉小)組立⑤[/WorkName]
[WorkItem]2. BRACKET にSWITCH をNUT-PLATE ･BOLT ･WASHER ･WASHER で取付
■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する
3. に1.完成品をBOLT ･WASHER で取付[/WorkItem]
[WorkPoint]取っ手取付用穴
IC供給有りの場合実施する[/WorkPoint]
[Tolk]1.0N･m[/Tolk]
[Inspect... | [QualityItem]型式確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]型式が一致する事[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-032[/RecordMethod]
[Other]-[/Other]
[ProcessName]安全工程[/ProcessName] | information_extraction | 2313 | |
[ToolName]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/ToolName]
[Size]3㎜[/Size]
[ToolOther]194cN･m[/ToolOther]
[WorkName]上側前面扉取付[/WorkName]
[WorkItem]1. に をBOLT WASHER で取付[/WorkItem]
[WorkPoint]矢印方向に当付け固定[/WorkPoint]
[Tolk]194cN･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]194cN･m±10%[/StdVal]
[Method]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2314 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ﾌﾚｰﾑｷｯﾄ(扉小)組立⑤[/WorkName]
[WorkItem]2. BRACKET にSWITCH をNUT-PLATE ･BOLT ･WASHER ･WASHER で取付
■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する
3. に1.完成品をBOLT ･WASHER で取付[/WorkItem]
[WorkPoint]取っ手取付用穴
IC供給有りの場合実施する[/WorkPoint]
[Tolk]1.0N･m[/Tolk]
[Inspect... | [QualityItem]製造番号記録[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]製造番号転記[/StdVal]
[Method]目視[/Method]
[RecordMethod]WWYJ-5300-032[/RecordMethod]
[Other]-[/Other]
[ProcessName]安全工程[/ProcessName] | information_extraction | 2315 | |
[ToolName]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/ToolName]
[Size]ﾍｸｻﾛT20[/Size]
[ToolOther]1.0N･m[/ToolOther]
[WorkName]ﾌﾚｰﾑｷｯﾄ(扉小)組立⑤[/WorkName]
[WorkItem]2. BRACKET にSWITCH をNUT-PLATE ･BOLT ･WASHER ･WASHER で取付
■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する
3. に1.完成品をBOLT ･WASHER で取付[/WorkItem]
[WorkPoint]IC供給有りの場合実施する[/WorkPoint]
[Tolk]1.0N･m[/To... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]1.0N･m±10%[/StdVal]
[Method]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]安全工程[/ProcessName] | information_extraction | 2316 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ﾌﾚｰﾑｷｯﾄ(扉小)組立⑥[/WorkName]
[WorkItem]1. にBRACKET ･ をBOLT ･BOLT ･WASHER で取付[/WorkItem]
[WorkPoint]BRACKET ･ はﾌﾚｰﾑ中央で垂直になる様に取付
IC供給有りの場合実施する
取っ手取付用穴[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2317 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ﾌﾚｰﾑｷｯﾄ(扉小)組立⑦[/WorkName]
[WorkItem]1. にPULL を取付[/WorkItem]
[WorkPoint]IC供給有りの場合実施する
取付方向注意
外側面から挿入し､ﾜﾝﾀｯﾁ留め具を押し込み固定[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]外側面
押し込む方向
内側面[/Words... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2318 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ﾌﾚｰﾑｷｯﾄ(扉小)組立⑧[/WorkName]
[WorkItem]1. にHINGE をBOLT ･WASHER で取付[/WorkItem]
[WorkPoint]IC供給有りの場合実施する
取付方向注意
取付方向注意[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]×3
外側面
×3
×3
×3[/Words... | [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2319 | |
[ToolName]ｱﾙｺｰﾙ[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]切替台座部(支持部側)組立①[/WorkName]
[WorkItem]1. BRACKET に油砥石かけ[/WorkItem]
[WorkPoint]指定箇所に油砥石をかける
油砥石かけ[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]脱脂確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示箇所が脱脂されている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]保護ﾒｶﾞﾈ[/Other]
[ProcessName]作業者安全工程[/ProcessName] | information_extraction | 2320 | |
[ToolName]油砥石[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]切替台座部(支持部側)組立①[/WorkName]
[WorkItem]1. BRACKET に油砥石かけ[/WorkItem]
[WorkPoint]指定箇所に油砥石をかける
油砥石かけ[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]表面確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]ﾊﾞﾘ､ｶｴﾘ等無い事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2321 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]切替台座部(支持部側)組立②[/WorkName]
[WorkItem]◆1. STOPPER STOPPER のﾗﾍﾞﾙ貼付け部の油分を除去する
2. 1の完成品へLABEL を指定の寸法で貼付ける
◆3. BOLT SPRING にｸﾞﾘｰｽ塗布[/WorkItem]
[WorkPoint]指示箇所へ塗布する
3mm
1mm
4mm
1mm
3mm
1mm[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/Inspection... | [QualityItem]塗布量[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示箇所に塗布小豆2個[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]ｸﾞﾘｰｽ[/Other]
[ProcessName]作業者安全工程[/ProcessName] | information_extraction | 2322 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]切替台座部(支持部側)組立②[/WorkName]
[WorkItem]◆1. STOPPER STOPPER のﾗﾍﾞﾙ貼付け部の油分を除去する
2. 1の完成品へLABEL を指定の寸法で貼付ける
◆3. BOLT SPRING にｸﾞﾘｰｽ塗布[/WorkItem]
[WorkPoint]指示箇所へ塗布する
3mm
1mm
4mm
1mm
3mm
1mm[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/Inspection... | [QualityItem]塗布量[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示箇所に塗布小豆:各1個[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]ｸﾞﾘｰｽ[/Other]
[ProcessName]作業者安全工程[/ProcessName] | information_extraction | 2323 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]切替台座部(支持部側)組立③[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint]PIN の出代10mm
PIN の圧入方向､場所に注意(下図参照)[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]出代確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]目安出代:10㎜±0.5㎜[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2324 | |
[ToolName]平面調整ｼﾞｸﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5040[/ToolOther]
[WorkName]内臓水準器ﾚﾍﾞﾙ出し調整[/WorkName]
[WorkItem]1. 引き出部の水準を確認[/WorkItem]
[WorkPoint]X･Y方向: 0.05mm/m以内
X･Y方向: 0.05mm/m以内
0.02mm/目盛[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]取付確認[/QualityItem]
[ToolManageNo]FM-5040[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付けられている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2325 | |
[ToolName]ﾄﾙｸﾚﾝﾁ[/ToolName]
[Size]5㎜[/Size]
[ToolOther]9.8N･m[/ToolOther]
[WorkName]切替台座部(支持部側)組立③[/WorkName]
[WorkItem]1. にPIN を圧入
2. 1の完成品にCOLLAR BOLT WASHER を取付[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk]9.8N･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]9.8N･m±10%[/StdVal]
[Method]ﾄﾙｸﾚﾝﾁ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2326 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]切替台座部(支持部側)組立④[/WorkName]
[WorkItem]1. にPLATE を取付[/WorkItem]
[WorkPoint]PLATE の取付方向に注意(下図参照)[/WorkPoint]
[Tolk]9.8N･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]取付方向確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付け出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2327 | |
[ToolName]ﾄﾙｸﾚﾝﾁ[/ToolName]
[Size]5㎜[/Size]
[ToolOther]9.8N･m[/ToolOther]
[WorkName]切替台座部(支持部側)組立④[/WorkName]
[WorkItem]1. にPLATE を取付[/WorkItem]
[WorkPoint]PLATE の取付方向に注意(下図参照)[/WorkPoint]
[Tolk]9.8N･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]9.8N･m±10%[/StdVal]
[Method]ﾄﾙｸﾚﾝﾁ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2328 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]切替台座部(支持部側)組立⑤[/WorkName]
[WorkItem]1. にBOLT WASHER を挿入し､ をBOLT WASHER で取付[/WorkItem]
[WorkPoint]BOLT WASHER を挿入してから を取付する事
ﾎﾞﾙﾄの出代調整の為WASHER を2枚入れる
の取付向きに注意(下図参照)[/WorkPoint]
[Tolk]150cN･m[/Tolk]
[InspectionNo][/InspectionNo]
[Inspectio... | [QualityItem]取付方向確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付け出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2329 | |
[ToolName]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/ToolName]
[Size]2.5㎜[/Size]
[ToolOther]150cN･m[/ToolOther]
[WorkName]切替台座部(支持部側)組立⑤[/WorkName]
[WorkItem]1. にBOLT WASHER を挿入し､ をBOLT WASHER で取付[/WorkItem]
[WorkPoint]BOLT WASHER を挿入してから を取付する事
ﾎﾞﾙﾄの出代調整の為WASHER を2枚入れる
の取付向きに注意(下図参照)[/WorkPoint]
[Tolk]150cN･m[/Tolk]
[InspectionNo][/Inspe... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]150cN･m±10%[/StdVal]
[Method]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2330 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]切替台座部(支持部側)組立⑥[/WorkName]
[WorkItem]1. にBOLT を挿入し､ をBOLT WASHER で取付[/WorkItem]
[WorkPoint]BOLT を挿入してから を取付する事
の取付向きに注意(下図参照)[/WorkPoint]
[Tolk]150cN･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]... | [QualityItem]取付方向確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付け出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2331 | |
[ToolName]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/ToolName]
[Size]2.5㎜[/Size]
[ToolOther]150cN･m[/ToolOther]
[WorkName]切替台座部(支持部側)組立⑥[/WorkName]
[WorkItem]1. にBOLT を挿入し､ をBOLT WASHER で取付[/WorkItem]
[WorkPoint]BOLT を挿入してから を取付する事
の取付向きに注意(下図参照)[/WorkPoint]
[Tolk]150cN･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionIt... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]150cN･m±10%[/StdVal]
[Method]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2332 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]切替台座部(支持部側)組立⑦[/WorkName]
[WorkItem]1. にCAP を挿入[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付け出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2333 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]切替台座部(支持部側)組立⑧[/WorkName]
[WorkItem]◆1. のﾗﾍﾞﾙ貼付面を脱脂し､LABEL LABEL ④を貼付け[/WorkItem]
[WorkPoint]各銘板の貼付け向きに注意(下図参照)
3mm
3mm
3mm
3mm
4mm
ﾗﾍﾞﾙ貼付け面[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[W... | [QualityItem]脱脂確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示箇所が脱脂されている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]保護ﾒｶﾞﾈ[/Other]
[ProcessName]作業者安全工程[/ProcessName] | information_extraction | 2334 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]切替台座部(支持部側)組立⑧[/WorkName]
[WorkItem]◆1. のﾗﾍﾞﾙ貼付面を脱脂し､LABEL LABEL ④を貼付け[/WorkItem]
[WorkPoint]各銘板の貼付け向きに注意(下図参照)
3mm
3mm
3mm
3mm
4mm
ﾗﾍﾞﾙ貼付け面[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[W... | [QualityItem]取付位置確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付けられている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]作業者安全工程[/ProcessName] | information_extraction | 2335 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]操作ﾊﾟﾈﾙｹｰﾌﾞﾙ固定(REAR)[/WorkName]
[WorkItem]1. ｽﾄｯﾊﾟｰにｹｰﾌﾞﾙを固定する[/WorkItem]
[WorkPoint]RSW2R
RSW1R
S312P
2A04
1A04
3A04
G104P
B212P
11S202~32S202
配線出代:ｺﾈｸﾀより10~15㎜の事[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionIt... | [QualityItem]作業確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]作業指示通り作業してある事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2336 | |
[ToolName]水準器[/ToolName]
[Size]0.02㎜/目盛[/Size]
[ToolOther][/ToolOther]
[WorkName]内臓水準器ﾚﾍﾞﾙ出し調整[/WorkName]
[WorkItem]1. 引き出部の水準を確認[/WorkItem]
[WorkPoint]X･Y方向: 0.05mm/m以内
X･Y方向: 0.05mm/m以内
0.02mm/目盛[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]ﾚﾍﾞﾙ調整[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]0.05㎜/m以内[/StdVal]
[Method]水準器[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2337 | |
[ToolName]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/ToolName]
[Size]3㎜[/Size]
[ToolOther]194cN･m[/ToolOther]
[WorkName]持ち手取付①[/WorkName]
[WorkItem]1. BRACKET にGUIDE PAD をSPACER BOLT BOLT WASHER WASHER で取付[/WorkItem]
[WorkPoint]下方向に当付けて取付
青の矢印方向から見たもの[/WorkPoint]
[Tolk]194cN･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/Inspectio... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]194cN･m±10%[/StdVal]
[Method]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2338 | |
[ToolName]ﾄﾙｸﾚﾝﾁ[/ToolName]
[Size]5㎜[/Size]
[ToolOther]6.0N･m[/ToolOther]
[WorkName]持ち手取付②[/WorkName]
[WorkItem]1. にPULL をBOLT WASHER WASHER NUT で取付[/WorkItem]
[WorkPoint]表側
裏側[/WorkPoint]
[Tolk]6.0N･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]6.0N･m±10%[/StdVal]
[Method]ﾄﾙｸﾚﾝﾁ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2339 | |
[ToolName]ﾄﾙｸﾚﾝﾁ[/ToolName]
[Size]6㎜[/Size]
[ToolOther]20.5N･m[/ToolOther]
[WorkName]連結ﾌﾞﾛｯｸ取付①[/WorkName]
[WorkItem]1. に をBOLT にて取付[/WorkItem]
[WorkPoint]前方向視野
横方向視野
青線部当てつけ｡ｼｯｸﾈｽｹﾞｰｼﾞ0.03㎜が入ら無い事[/WorkPoint]
[Tolk]20.5N･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]【A矢視図】[... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]20.5N･m±10%[/StdVal]
[Method]ﾄﾙｸﾚﾝﾁ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2340 | |
[ToolName]ｼｯｸﾈｽｹﾞｰｼﾞ[/ToolName]
[Size]0.03㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]連結ﾌﾞﾛｯｸ取付①[/WorkName]
[WorkItem]1. に をBOLT にて取付[/WorkItem]
[WorkPoint]前方向視野
横方向視野
青線部当てつけ｡ｼｯｸﾈｽｹﾞｰｼﾞ0.03㎜が入ら無い事[/WorkPoint]
[Tolk]20.5N･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]【A矢視図】[... | [QualityItem]隙間確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]0.03㎜が入ら無い事[/StdVal]
[Method]ｼｯｸﾈｽｹﾞｰｼﾞ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2341 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]連結ﾌﾞﾛｯｸ取付②[/WorkName]
[WorkItem]2. にSPRING とPLATE をBOLT にて取付
3. 2.完成品にCAP を取付
◆1. SPRING とBOLT にｸﾞﾘｰｽを塗布[/WorkItem]
[WorkPoint]図の指示部に塗布すこと
PLATE の取付向きに注意:小さい穴の方にﾎﾞﾙﾄを通す[/WorkPoint]
[Tolk]9.8N･m[/Tolk]
[InspectionNo][/InspectionNo]
[Inspe... | [QualityItem]塗布量[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示箇所に塗布小豆粒:各1[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]ｸﾞﾘｰｽ[/Other]
[ProcessName]作業者安全工程[/ProcessName] | information_extraction | 2342 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]連結ﾌﾞﾛｯｸ取付②[/WorkName]
[WorkItem]2. にSPRING とPLATE をBOLT にて取付
3. 2.完成品にCAP を取付
◆1. SPRING とBOLT にｸﾞﾘｰｽを塗布[/WorkItem]
[WorkPoint]図の指示部に塗布すこと
PLATE の取付向きに注意:小さい穴の方にﾎﾞﾙﾄを通す[/WorkPoint]
[Tolk]9.8N･m[/Tolk]
[InspectionNo][/InspectionNo]
[Inspe... | [QualityItem]塗布量[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示箇所に塗布小豆粒:2[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]ｸﾞﾘｰｽ[/Other]
[ProcessName]作業者安全工程[/ProcessName] | information_extraction | 2343 | |
[ToolName]ﾄﾙｸﾚﾝﾁ[/ToolName]
[Size]5㎜[/Size]
[ToolOther]9.8N･m[/ToolOther]
[WorkName]連結ﾌﾞﾛｯｸ取付②[/WorkName]
[WorkItem]2. にSPRING とPLATE をBOLT にて取付
◆1. SPRING とBOLT にｸﾞﾘｰｽを塗布[/WorkItem]
[WorkPoint]図の指示部に塗布すこと
PLATE の取付向きに注意:小さい穴の方にﾎﾞﾙﾄを通す[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]9.8N･m±10%[/StdVal]
[Method]ﾄﾙｸﾚﾝﾁ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2344 | |
[ToolName]ﾄﾙｸﾚﾝﾁ[/ToolName]
[Size]2.5㎜[/Size]
[ToolOther]150cN･m[/ToolOther]
[WorkName]連結ﾌﾞﾛｯｸ取付③[/WorkName]
[WorkItem]1. にBOLT WASHER を差込み、 をBOLT ㉒で取付[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk]150cN･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]150cN･m±10%[/StdVal]
[Method]ﾄﾙｸﾚﾝﾁ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2345 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ﾌﾞﾛｯｸ取付[/WorkName]
[WorkItem]1. に作業1完成品をBOLT WASHER で仮取付
1. にBOLT を差込む[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]仮止め:SD-A048810-005にて本締め[/Words]
| [QualityItem]取付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り取付出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2346 | |
[ToolName]ﾄﾙｸﾚﾝﾁ[/ToolName]
[Size]4㎜[/Size]
[ToolOther]3.6N･m[/ToolOther]
[WorkName]固定ﾌﾞﾗｹｯﾄ取付[/WorkName]
[WorkItem]1. に をBOLT WASHER にて取付[/WorkItem]
[WorkPoint] を矢印方向に押し当てながら締結
を矢印方向に押し当てながら締結[/WorkPoint]
[Tolk]3.6N･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]3.6N･m±10%[/StdVal]
[Method]ﾄﾙｸﾚﾝﾁ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2347 | |
[ToolName]ﾄﾙｸﾚﾝﾁ[/ToolName]
[Size]3㎜[/Size]
[ToolOther]3.2N･m[/ToolOther]
[WorkName]内臓水準器ﾚﾍﾞﾙ出し調整[/WorkName]
[WorkItem]2. 内蔵水準器の気泡調整[/WorkItem]
[WorkPoint]内蔵水準器 '0' に調整
長い線の間に気泡
最終工程で確認の為､調整のみ[/WorkPoint]
[Tolk]3.2N･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]3.2N･m±10%[/StdVal]
[Method]ﾄﾙｸﾚﾝﾁ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2348 | |
[ToolName]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/ToolName]
[Size]2.5㎜[/Size]
[ToolOther]95cN･m[/ToolOther]
[WorkName]ﾌﾞﾗｹｯﾄ取付[/WorkName]
[WorkItem]1. にBRACKET をBOLT WASHER BOLT WASHER で取付
2. 1完成品にBRACKET をBOLT WASHER にて取付[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk]194cN･m
締付ﾄﾙｸ 95cN･m
締付ﾄﾙｸ 194cN･m[/Tolk]
[InspectionNo][/InspectionNo]
... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]95cN･m±10%[/StdVal]
[Method]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2349 | |
[ToolName]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/ToolName]
[Size]3㎜[/Size]
[ToolOther]194cN･m[/ToolOther]
[WorkName]ﾌﾞﾗｹｯﾄ取付[/WorkName]
[WorkItem]1. にBRACKET をBOLT WASHER BOLT WASHER で取付
2. 1完成品にBRACKET をBOLT WASHER にて取付[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk]194cN･m
締付ﾄﾙｸ 95cN･m
締付ﾄﾙｸ 194cN･m[/Tolk]
[InspectionNo][/InspectionNo]
[... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]194cN･m±10%[/StdVal]
[Method]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2350 | |
[ToolName]ﾄﾙｸﾚﾝﾁ[/ToolName]
[Size]3㎜[/Size]
[ToolOther]194cN･m[/ToolOther]
[WorkName]ﾌﾞﾗｹｯﾄ取付[/WorkName]
[WorkItem][/WorkItem]
[WorkPoint]このﾎﾞﾙﾄ2本は調整後に本締めする
このﾎﾞﾙﾄは調整後に本締めする[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]194cN･m±10%[/StdVal]
[Method]ﾄﾙｸﾚﾝﾁ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2351 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]配管配線接続[/WorkName]
[WorkItem]1. 片方のJOINT にCAP をはめ込む
2. に作業1完成品とJOINT TUBE TUBE CABLE を接続[/WorkItem]
[WorkPoint]配管白線有り
配管白線無し
赤ｷｬｯﾌﾟCAP 付き継ぎ手に接続する配管は白線無しを接続する事
※前工程で取付けられたｼﾞｮｲﾝﾄを取り外す事
不要取り外し[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/Inspe... | [QualityItem]配線配管処理確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通りに接続出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2352 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]配管配線結束[/WorkName]
[WorkItem]1. 指定した寸法で配線配管を結束[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]ｲﾝｼｭﾛｯｸ指示
･ｹｰﾌﾞﾙ同士を固定
･ﾀｲﾏｳﾝﾄに固定 又は板金に固定
85㎜
30㎜[/Words]
| [QualityItem]寸法確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示寸法各±1.0㎜[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2353 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]銘板貼付け①[/WorkName]
[WorkItem]2. にLABEL LABEL を指定の寸法で貼付け
◆1. 銘板貼付け面の油分を除去[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]15㎜
2㎜[/Words]
| [QualityItem]貼付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]寸法の位置に貼付けている事指示寸法±0.5㎜[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2354 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]銘板貼付け②[/WorkName]
[WorkItem]2. にLABEL LABEL LABEL を指定の寸法で貼付け
◆1. 銘板貼付け面の油分を除去[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]172㎜
121㎜
73㎜
86㎜
14㎜[/Words]... | [QualityItem]貼付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]寸法の位置に貼付けている事指示寸法±0.5㎜[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2355 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]銘板貼付け③[/WorkName]
[WorkItem]2. にLABEL ⑦を指定の寸法で貼付け
◆1. 銘板貼付け面の油分を除去[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]貼付確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]寸法の位置に貼付けている事指示寸法±0.5㎜[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2356 | |
[ToolName]ｽｹｰﾙ[/ToolName]
[Size]150㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]持ち手取付[/WorkName]
[WorkItem]1. GRIP にNUT を取付
2. に作業1完成品を指定寸法で取付[/WorkItem]
[WorkPoint]作業1完成品
持ち手とﾌﾚｰﾑの隙間を6.0±0.5㎜[/WorkPoint]
[Tolk]20.5N･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]6㎜[/Words]
| [QualityItem]寸法確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示寸法各±0.5㎜[/StdVal]
[Method]ｽｹｰﾙ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2357 | |
[ToolName]ﾄﾙｸｽﾊﾟﾅ[/ToolName]
[Size]13㎜[/Size]
[ToolOther]20.5N･m[/ToolOther]
[WorkName]持ち手取付[/WorkName]
[WorkItem]1. GRIP にNUT を取付
2. に作業1完成品を指定寸法で取付[/WorkItem]
[WorkPoint]作業1完成品
持ち手とﾌﾚｰﾑの隙間を6.0±0.5㎜[/WorkPoint]
[Tolk]20.5N･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]6㎜[/... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]20.5N･m±10%[/StdVal]
[Method]ﾄﾙｸｽﾊﾟﾅ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2358 | |
[ToolName]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/ToolName]
[Size]2.5㎜[/Size]
[ToolOther]95cN･m[/ToolOther]
[WorkName]ｶﾊﾞｰ用SWﾌﾞﾗｹｯﾄ取付[/WorkName]
[WorkItem]1. に SPACER をBOLT WASHER で取付
2. 1完成品のｺﾈｸﾀを接続する[/WorkItem]
[WorkPoint]ﾌﾞﾗｹｯﾄとの隙間:1.8㎜ (下図参照)[/WorkPoint]
[Tolk]95cN･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionI... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]95cN･m±10%[/StdVal]
[Method]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2359 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ﾊｰﾈｽ準備①[/WorkName]
[WorkItem]1. 下記ﾘｽﾄでｹｰﾌﾞﾙを準備する[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]ｹｰﾌﾞﾙ準備確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り準備出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2360 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ﾊｰﾈｽ準備②(OP)[/WorkName]
[WorkItem]1. 下記ﾘｽﾄでｹｰﾌﾞﾙを準備する[/WorkItem]
[WorkPoint][/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]ｹｰﾌﾞﾙ準備確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り準備出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2361 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A010)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]PCN53
B010[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2362 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A011)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]PCN23
G102P
G101P[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2363 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A012)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]PCN13
CN9A002[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2364 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A015)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]PCN18
B001P[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2365 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A016)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]PCN15
B009P[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2366 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A017)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]PCN21
T202
PCN51[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2367 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A019)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]T201 I/F
PCN52
T201 I/L
T201DC
PCN22[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Wo... | [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2368 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A020)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]F302P
F306P
B019P
PCN17[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2369 | |
[ToolName]ｼｯｸﾈｽｹﾞｰｼﾞ[/ToolName]
[Size]1.8㎜[/Size]
[ToolOther][/ToolOther]
[WorkName]ｶﾊﾞｰ用SWﾌﾞﾗｹｯﾄ取付[/WorkName]
[WorkItem]1. に SPACER をBOLT WASHER で取付
2. 1完成品のｺﾈｸﾀを接続する[/WorkItem]
[WorkPoint]ﾌﾞﾗｹｯﾄとの隙間:1.8㎜ (下図参照)[/WorkPoint]
[Tolk]95cN･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
... | [QualityItem]隙間確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]隙間:1.8㎜[/StdVal]
[Method]ｼｯｸﾈｽｹﾞｰｼﾞ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2370 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A024)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]G112P
G111P
PCN16[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2371 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A028)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]S001R
S201
PCN14[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2372 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A029)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]F304P
F303P
F305P
PCN19[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2373 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A030)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]F311P
PCN20[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2374 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A031)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]X103-1
X200R
PCN5[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2375 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A032)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]X103-3
K352-1[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2376 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A035)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]B008P
PCN11[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2377 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A077)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]DRP I/FP
PCN24[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2378 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A079)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]ｺﾈｸﾀ形状
ｺﾈｸﾀ形状[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2379 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A054)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]X202-8R
PCN6
X201R[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2380 | |
[ToolName]-[/ToolName]
[Size][/Size]
[ToolOther][/ToolOther]
[WorkName]ｶﾊﾞｰ用SWﾌﾞﾗｹｯﾄ取付[/WorkName]
[WorkItem]1. に SPACER をBOLT WASHER で取付
2. 1完成品のｺﾈｸﾀを接続する[/WorkItem]
[WorkPoint]ﾌﾞﾗｹｯﾄとの隙間:1.8㎜ (下図参照)[/WorkPoint]
[Tolk]95cN･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words]検査表 :ｺ... | [QualityItem]接続確認[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]-[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り接続出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]WEPJ-G002-D33[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2381 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A068)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]K352-2
X102-1[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2382 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A069)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]X103-4
F311-1[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2383 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A049)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]X200-2R
F311-P1･P2[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2384 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A036)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]F312-P1･P2
X201-3R[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2385 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A051)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]X200-5R
K301PTP[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2386 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A041)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]K302-2
X102-5[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2387 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A071)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]X102-4
X104-1[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2388 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A044)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]232CK351
1232CA002R[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2389 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A067)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]F312-1
X102-3[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2390 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A080)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]PCN29
POWK361P[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2391 | |
[ToolName]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/ToolName]
[Size]3㎜[/Size]
[ToolOther]194cN･m[/ToolOther]
[WorkName]補給完了SWﾌﾞﾗｹｯﾄ取付[/WorkName]
[WorkItem]1. に をBOLT WASHER で取付[/WorkItem]
[WorkPoint]説明の為にｽｲｯﾁを消しています
傾きがないように取付[/WorkPoint]
[Tolk]194cN･m[/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]... | [QualityItem]締付ﾄﾙｸ[/QualityItem]
[ToolManageNo]-[/ToolManageNo]
[ToolCycle]日常点検(1回/日)[/ToolCycle]
[ToolRecord]ﾄﾙｸﾁｪｯｸ台帳[/ToolRecord]
[StdVal]194cN･m±10%[/StdVal]
[Method]ﾄﾙｸﾄﾞﾗｲﾊﾞｰ[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2392 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A081)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]5X003
1X005[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2393 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A063)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]FGF312
4X001[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2394 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(USB2)[/WorkName]
[WorkItem]1. 下図参照し をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]USB2K351
USB1[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2395 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(USB3)[/WorkName]
[WorkItem]1. 下図参照し をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]USB3K351
USB2[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2396 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(USB4)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]CABLE 232CT202
CABLE 1USB4Rと 1USB4PのIODeviceと接続する
USB4K351[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/Inspect... | [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2397 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(LAN1)[/WorkName]
[WorkItem]1. 下図参照し をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]LAN1K351
LAN1P[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2398 | |
[ToolName]ﾊｰﾈｽﾎﾞｰﾄﾞ[/ToolName]
[Size][/Size]
[ToolOther]FM-5172[/ToolOther]
[WorkName]束配線(A062)[/WorkName]
[WorkItem]1. 下図参照しCABLE をﾊｰﾈｽﾎﾞｰﾄﾞに引き回す[/WorkItem]
[WorkPoint]2X003
FGF311[/WorkPoint]
[Tolk][/Tolk]
[InspectionNo][/InspectionNo]
[InspectionItem][/InspectionItem]
[Words][/Words]
| [QualityItem]引き回確認[/QualityItem]
[ToolManageNo]FM-5172[/ToolManageNo]
[ToolCycle]校正対象外[/ToolCycle]
[ToolRecord]-[/ToolRecord]
[StdVal]指示通り引き回出来ている事[/StdVal]
[Method]目視[/Method]
[RecordMethod]-[/RecordMethod]
[Other]-[/Other]
[ProcessName]-[/ProcessName] | information_extraction | 2399 |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.