input stringclasses 1
value | instruction stringlengths 202 3.29k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｼﾞｮｲﾝﾄﾌﾞﾗｹｯﾄ、ｾﾝｻｰ取付",
"WorkItems": [
"1. に をBOLT WASHER で取付ける",
"1. にWASHER をBOLT WASHER で仮付け"
],
"WorkPoints": [
"SD-0164025-030で本締結"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "配管①",
"WorkItems": [
"1. にJOINT とTUBE を取付ける"
],
"WorkPoints": [
"下記寸法に配管を切る事",
"A.90mm B.260mm C.150mm D.110mm",
"※ 先端ﾌﾗｯﾄﾀｲﾌﾟのﾗｼﾞﾍﾟﾝで 確実に最後まで押入する事"
],
"Tolks": [],
"InspectionNo": "",
"Inspection... | {
"QualityItem": "長さ確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りの長さでｶｯﾄしてある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管①",
"WorkItems": [
"1. にJOINT とTUBE を取付ける"
],
"WorkPoints": [
"下記寸法に配管を切る事",
"A.90mm B.260mm C.150mm D.110mm",
"※ 先端ﾌﾗｯﾄﾀｲﾌﾟのﾗｼﾞﾍﾟﾝで 確実に最後まで押入する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems":... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りに接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "配管②",
"WorkItems": [
"1. にTUBE を取付ける"
],
"WorkPoints": [
"下記寸法に配管を切る事",
"E.150mm F.210mm G.110mm",
"※ 先端ﾌﾗｯﾄﾀｲﾌﾟのﾗｼﾞﾍﾟﾝで 確実に最後まで押入する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "長さ確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りの長さでｶｯﾄしてある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管②",
"WorkItems": [
"1. にTUBE を取付ける"
],
"WorkPoints": [
"下記寸法に配管を切る事",
"E.150mm F.210mm G.110mm",
"※ 先端ﾌﾗｯﾄﾀｲﾌﾟのﾗｼﾞﾍﾟﾝで 確実に最後まで押入する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りに接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線",
"WorkItems": [
"1. 各ｺﾈｸﾀに配線を接続する"
],
"WorkPoints": [
"･干渉し無い事",
"･配線2本をｲﾝｼｭﾛｯｸで固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"B****R/P",
"B****R/P",
"1B****",
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りに接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線",
"WorkItems": [
"1. 各ｺﾈｸﾀに配線を接続する"
],
"WorkPoints": [
"･干渉し無い事",
"･配線2本をｲﾝｼｭﾛｯｸで固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"B****R/P",
"B****R/P",
"1B****",
... | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "干渉無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "結束・整線",
"WorkItems": [
"1. 配管をｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"ﾘﾆｱﾌﾞｯｼｭ側に線を入れる｡赤線より外側に出無い事(自動ﾋﾟﾝﾌﾞﾛｯｸに干渉恐れ)",
"ﾍﾞｰｽﾌﾟﾚｰﾄ全面に防錆油塗布",
"ｾﾝｻの可動範囲を確認し結束"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "P002ﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. に を載せる"
],
"WorkPoints": [
"こじれるとﾎﾞｰﾙｽﾌﾟﾗｲﾝを破損するので注意",
"SD-0164025-028で本締結"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"･載せる前に のｼｬﾌﾄ4本が動く程度に仮締... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに取付してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "昇降ﾌﾟﾚｰﾄ位置決め治具ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "FM-3165-",
"WorkName": "P002ﾌﾟﾚｰﾄ位置調整",
"WorkItems": [
"1. のｼｬﾌﾄの向きを調整しﾎﾞﾙﾄを締結し､WASHER をBOLT で取付ける",
"2. 組立台(FM-2777）に㉗を取付ける",
"3. 隙間確認･調整する"
],
"WorkPoints": [
"治具とﾍﾞｰｽﾌﾟﾚｰﾄにｽｷﾏ無き事",
"ｽｷﾏ無き事",
"ｼｯｸﾈｽｹ... | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-3165-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "P002ﾌﾟﾚｰﾄ位置調整",
"WorkItems": [],
"WorkPoints": [
"治具とﾍﾞｰｽﾌﾟﾚｰﾄにｽｷﾏ無き事",
"ｼｯｸﾈｽｹﾞｰｼﾞt=0.05mmが通ら無い事",
"ｼｯｸﾈｽｹﾞｰｼﾞt=0.05mmが通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo":... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "P002ﾌﾟﾚｰﾄ位置調整",
"WorkItems": [],
"WorkPoints": [
"治具とﾍﾞｰｽﾌﾟﾚｰﾄにｽｷﾏ無き事",
"ｼｯｸﾈｽｹﾞｰｼﾞt=0.05mmが通ら無い事",
"ｼｯｸﾈｽｹﾞｰｼﾞt=0.05mmが通ら無い事",
"治具とﾍﾞｰｽﾌﾟﾚｰﾄにｽｷﾏ無き事",
"ｼｯｸﾈｽｹﾞｰｼﾞt=0.05mmが通ら無い事",
"ｼｯｸﾈｽｹﾞｰｼﾞt=0.05mm... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰｼﾘﾝﾀﾞｰ位置調整治具",
"Size": "",
"ToolOther": "FM-2999FM-2982",
"WorkName": "ｼﾘﾝﾀﾞｰﾅｯﾄ固定",
"WorkItems": [
"2. ㉘でプレートとシリンダーの芯出しを行いシリンダーを固定する",
"◆3. CYL-NUT WASHER をｼﾘﾝﾀﾞｰに取付",
"4. ｼﾘﾝﾀﾞｰをｽﾊﾟﾅの入る位置まで上昇させ､ﾛｯﾄﾞの位置決め後ﾛｯｸする｡",
"1. に㉗の配管（Ф6）をつなぐ"
],
"WorkPoints": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999FM-2982",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N.m",
"WorkName": "ｼﾘﾝﾀﾞｰﾅｯﾄ固定",
"WorkItems": [],
"WorkPoints": [
"0.5MPaに設定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾘﾝﾀﾞｰﾅｯﾄ固定",
"WorkItems": [
"2. ㉘でプレートとシリンダーの芯出しを行いシリンダーを固定する",
"◆3. CYL-NUT WASHER をｼﾘﾝﾀﾞｰに取付",
"4. ｼﾘﾝﾀﾞｰをｽﾊﾟﾅの入る位置まで上昇させ､ﾛｯﾄﾞの位置決め後ﾛｯｸする｡",
"1. に㉗の配管（Ф6）をつなぐ"
],
"WorkPoints": [
"0.5MPaに設定する",
"･最上死点及び最下... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒/8粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼﾘﾝﾀﾞｰﾅｯﾄ固定",
"WorkItems": [],
"WorkPoints": [
"㉚でロックする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"※CYL-NUTの穴の深さは8.5±0.05㎜",
"8.5±0.05㎜",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "8.5±0.05㎜",
"Method": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｾﾝｻｰﾄﾞｸﾞ取付",
"WorkItems": [
"1. にDOG をBOLT WASHER で取付ける"
],
"WorkPoints": [
"目分量でｾﾝﾀｰ",
"目分量で2/3",
"ｼﾘﾝﾀﾞｰを上下させ､DOG とｾﾝｻｰが接触しないよう調整する｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItem... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｾﾝｻｰﾄﾞｸﾞ取付",
"WorkItems": [
"1. にDOG をBOLT WASHER で取付ける"
],
"WorkPoints": [
"目分量でｾﾝﾀｰ",
"目分量で2/3",
"ｼﾘﾝﾀﾞｰを上下させ､DOG とｾﾝｻｰが接触しないよう調整する｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻｰﾄﾞｸﾞ取付",
"WorkItems": [
"1. にDOG をBOLT WASHER で取付ける"
],
"WorkPoints": [
"目分量でｾﾝﾀｰ",
"目分量で2/3",
"ｼﾘﾝﾀﾞｰを上下させ､DOG とｾﾝｻｰが接触しないよう調整する｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words"... | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "干渉無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "K024取付・調整①",
"WorkItems": [
"1. に をBOLT で取付ける",
"2. の位置決めをして固定する"
],
"WorkPoints": [
"A寸法:89.5±0.1㎜(ﾉｷﾞｽにて測定)"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "K024取付・調整①",
"WorkItems": [],
"WorkPoints": [
"A寸法:89.5±0.1㎜(ﾉｷﾞｽにて測定)"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"･治具FM-4139をｾｯﾄ X方向:ﾋﾟﾝをﾌﾟﾚｰﾄに当付... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基準ﾋﾟﾝﾌﾞﾛｯｸ位置決め治具",
"Size": "",
"ToolOther": "FM-4139",
"WorkName": "K024取付・調整①",
"WorkItems": [
"1. に をBOLT で取付ける",
"2. の位置決めをして固定する"
],
"WorkPoints": [
"A寸法:89.5±0.1㎜(ﾉｷﾞｽにて測定)"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4139",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "89.5±0.1㎜",
"Method": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "K024取付・調整①",
"WorkItems": [],
"WorkPoints": [
"A寸法:89.5±0.1㎜(ﾉｷﾞｽにて測定)"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"･治具FM-4139をｾｯﾄ X方向:ﾋﾟﾝをﾌﾟﾚｰﾄに当付... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "89.5±0.1㎜",
"Method": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "P018取付け",
"WorkItems": [
"1. にGUIDE をBOLT で取付ける｡"
],
"WorkPoints": [
"手前側に寄せて固定する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "P018取付け",
"WorkItems": [
"1. にGUIDE をBOLT で取付ける｡"
],
"WorkPoints": [
"手前側に寄せて固定する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ﾕﾆｯﾄﾁｪｯｶｰ操作説明",
"WorkItems": [],
"WorkPoints": [
"5.00~5.05MPa",
"注意｢③の切替時｣｢A･Bの上下動作時｣隣に同じく作業する作業者がい無い事(勘違いにより反対側を動作させてしまう恐れが有る)",
"動作しなくなった場合はｽﾄｯﾌﾟ及び電源OFF安全の為二人作業は禁止",
"AUTO動作",
"MANUAL動作",
"ﾕ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "P003、004ﾌﾟﾚｰﾄ取付・調整",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける｡",
"2. にPLATE PLATE をBOLT で取付ける｡",
"3. PLATE PLATE の取付け高さ調整および平面度を測定する｡"
],
"WorkPoints": [
"･ﾌﾞﾛｯｸｹﾞｰｼﾞ110.5㎜を治具台にﾍﾞｰｽﾌﾟﾚｰﾄ当付で取付",
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｸﾗﾝﾌﾟﾌﾞﾚｰﾄﾞ押上板位置出し治具昇降ﾌﾟﾚｰﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-3178FM-3165-",
"WorkName": "P003、004ﾌﾟﾚｰﾄ取付・調整",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける｡",
"2. にPLATE PLATE をBOLT で取付ける｡",
"3. PLATE PLATE の取付け高さ調整および平面度を測定する｡"
],
"WorkPoints": [
"･ﾌﾞﾛｯｸｹﾞｰｼﾞ110.5... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3178FM-3165-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N.m",
"WorkName": "P003、004ﾌﾟﾚｰﾄ取付・調整",
"WorkItems": [],
"WorkPoints": [
"･ﾌﾞﾛｯｸｹﾞｰｼﾞ110.5㎜を治具台にﾍﾞｰｽﾌﾟﾚｰﾄ当付で取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"49±0.1㎜",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N.m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "P003、004ﾌﾟﾚｰﾄ取付・調整",
"WorkItems": [],
"WorkPoints": [
"･ﾌﾞﾛｯｸｹﾞｰｼﾞ110.5㎜を治具台にﾍﾞｰｽﾌﾟﾚｰﾄ当付で取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"49±0.1㎜",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "49±0.1㎜",
"Method": "ﾃﾞｼﾞﾀﾙﾉｷﾞｽ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "P003、004ﾌﾟﾚｰﾄ取付・調整",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける｡",
"2. にPLATE PLATE をBOLT で取付ける｡",
"3. PLATE PLATE の取付け高さ調整および平面度を測定する｡"
],
"WorkPoints": [
"･ﾌﾞﾛｯｸｹﾞｰｼﾞ110.5㎜を治具台にﾍﾞｰｽﾌﾟﾚｰﾄ当付で取付",
... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年校正対象外",
"ToolRecord": "校正成績書-",
"StdVal": "110.5±0.05㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "P003、004ﾌﾟﾚｰﾄ・調整②",
"WorkItems": [
"1. を動作させ､上がった状態でのﾚｰﾙ平行を調整する"
],
"WorkPoints": [
"1.治具台にFM-3167をﾌﾛﾝﾄ側に取付 (ﾚｰﾙ端面より4㎜)2.ﾁｪｯｶｰでﾎﾙﾀﾞｰを上昇させる3.①を基準に②､④を基準に③を調整する (調整しにくい場合は下降させて上昇時の差分を調整する)4.下降させて①④が基準寸法(110.5±... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ上昇ｽﾄｯﾊﾟｰ",
"Size": "",
"ToolOther": "FM-3167",
"WorkName": "P003、004ﾌﾟﾚｰﾄ・調整②",
"WorkItems": [
"1. を動作させ､上がった状態でのﾚｰﾙ平行を調整する"
],
"WorkPoints": [
"1.治具台にFM-3167をﾌﾛﾝﾄ側に取付 (ﾚｰﾙ端面より4㎜)2.ﾁｪｯｶｰでﾎﾙﾀﾞｰを上昇させる3.①を基準に②､④を基準に③を調整する (調整しにくい場合は下降させて上昇時の差分を調整する)4.下降させて①④が基準寸法(110.... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3167",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "P003、004ﾌﾟﾚｰﾄ・調整②",
"WorkItems": [
"1. を動作させ､上がった状態でのﾚｰﾙ平行を調整する"
],
"WorkPoints": [
"1.治具台にFM-3167をﾌﾛﾝﾄ側に取付 (ﾚｰﾙ端面より4㎜)2.ﾁｪｯｶｰでﾎﾙﾀﾞｰを上昇させる3.①を基準に②､④を基準に③を調整する (調整しにくい場合は下降させて上昇時の差分を調整する)4.下降させて①④が基準寸法(110.5±0.05)に入っている... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "P003、004ﾌﾟﾚｰﾄ・調整②",
"WorkItems": [
"1. を動作させ､上がった状態でのﾚｰﾙ平行を調整する"
],
"WorkPoints": [
"1.治具台にFM-3167をﾌﾛﾝﾄ側に取付 (ﾚｰﾙ端面より4㎜)2.ﾁｪｯｶｰでﾎﾙﾀﾞｰを上昇させる3.①を基準に②､④を基準に③を調整する (調整しにくい場合は下降させて上昇時の差分を調整する)4.下降させて①④が基準寸法(110.5±0.05)... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "P003、004ﾌﾟﾚｰﾄ・調整②",
"WorkItems": [
"1. を動作させ､上がった状態でのﾚｰﾙ平行を調整する"
],
"WorkPoints": [
"1.治具台にFM-3167をﾌﾛﾝﾄ側に取付 (ﾚｰﾙ端面より4㎜)2.ﾁｪｯｶｰでﾎﾙﾀﾞｰを上昇させる3.①を基準に②､④を基準に③を調整する (調整しにくい場合は下降させて上昇時の差分を調整する)4.下降させて①④が基準寸法(11... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年校正対象外",
"ToolRecord": "校正成績書-",
"StdVal": "110.5±0.05㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "昇降ﾌﾟﾚｰﾄ位置決め治具ｸﾗﾝﾌﾟﾌﾞﾚｰﾄﾞ押上板位置出し治具",
"Size": "",
"ToolOther": "FM-3165FM-3178",
"WorkName": "P003、004ﾌﾟﾚｰﾄ・調整②",
"WorkItems": [
"1. を動作させ､上がった状態でのﾚｰﾙ平行を調整する"
],
"WorkPoints": [
"1.治具台にFM-3167をﾌﾛﾝﾄ側に取付 (ﾚｰﾙ端面より4㎜)2.ﾁｪｯｶｰでﾎﾙﾀﾞｰを上昇させる3.①を基準に②､④を基準に③を調整する (調整しにくい場合は下降させて上昇時の差... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3165FM-3178",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ基板ﾎﾙﾀﾞ上昇ｽﾄｯﾊﾟｰ",
"Size": "",
"ToolOther": "FM-2999FM-3167",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面調整",
"WorkItems": [
"1. ｱｼﾞｬｽﾄﾎﾞﾙﾄの平面度調整を行う"
],
"WorkPoints": [
"1番のｱｼﾞｬｽﾄﾎﾞﾙﾄを調整",
"規格値:2.5±0.025㎜",
"1番を基準として､2~8番のｱｼﾞｬｽﾄﾎﾞﾙﾄを調整",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄの一番高い場所で調整する",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999FM-3167",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/1000",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面調整",
"WorkItems": [
"1. ｱｼﾞｬｽﾄﾎﾞﾙﾄの平面度調整を行う"
],
"WorkPoints": [
"1番のｱｼﾞｬｽﾄﾎﾞﾙﾄを調整",
"規格値:2.5±0.025㎜",
"1番を基準として､2~8番のｱｼﾞｬｽﾄﾎﾞﾙﾄを調整",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄの一番高い場所で調整する",
"3･4･6の高さ:1番を基準に平面度0... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "2.5±0.025㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "下受ﾌﾟﾚｰﾄ搭載面調整治具",
"Size": "",
"ToolOther": "FM-4128",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面調整",
"WorkItems": [
"1. ｱｼﾞｬｽﾄﾎﾞﾙﾄの平面度調整を行う"
],
"WorkPoints": [
"1番のｱｼﾞｬｽﾄﾎﾞﾙﾄを調整",
"規格値:2.5±0.025㎜",
"1番を基準として､2~8番のｱｼﾞｬｽﾄﾎﾞﾙﾄを調整",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄの一番高い場所で調整する",
"3･4･6の高さ:1番を基準に平面... | {
"QualityItem": "平面度確認",
"ToolManageNo": "FM-4128",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "2.5±0.025㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰﾌﾞﾗｹｯﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-2999FM-3227",
"WorkName": "ｸﾗﾝﾌﾟ部取付･位置出し調整",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [
" は､取付け穴分奥側に寄せておく事",
"手で軽く回って､0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが入ら無い事｡"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"In... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999FM-3227",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｸﾗﾝﾌﾟ部取付･位置出し調整",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [
" は､取付け穴分奥側に寄せておく事",
"手で軽く回って､0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが入ら無い事｡"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"Ins... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "0.05㎜",
"WorkName": "ｸﾗﾝﾌﾟ部取付･位置出し調整",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [
" は､取付け穴分奥側に寄せておく事",
"手で軽く回って､0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが入ら無い事｡"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"In... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "六角ﾎﾟｽﾄ取付",
"WorkItems": [
"1. に を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "P607ｶﾊﾞｰ取付",
"WorkItems": [
"1. にCOVER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N.m",
"WorkName": "P607ｶﾊﾞｰ取付",
"WorkItems": [
"1. にCOVER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"1. ｴｰｼﾞﾝｸﾞを実施する"
],
"WorkPoints": [
"注意｢③の切替時｣｢A･Bの上下動作時｣隣に同じく作業する作業者がい無い事(勘違いにより反対側を動作させてしまう恐れが有る)",
"ﾕﾆｯﾄﾁｪｯｶｰ使用前にｴｱｰ圧力確認を行う事:0.5~0.505MPa",
"動作しなくなった場合はｽﾄｯﾌﾟ及び電源OFF安全の為二人作... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｴｱｰ圧力:0.5~0.505MPa",
"Method": "ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"1. ｴｰｼﾞﾝｸﾞを実施する"
],
"WorkPoints": [
"注意｢③の切替時｣｢A･Bの上下動作時｣隣に同じく作業する作業者がい無い事(勘違いにより反対側を動作させてしまう恐れが有る)",
"ﾕﾆｯﾄﾁｪｯｶｰ使用前にｴｱｰ圧力確認を行う事:0.5~0.505MPa",
"動作しなくなった場合はｽﾄｯﾌﾟ及び電源OFF安全の為二人作... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｴﾗｰ無き事",
"Method": "ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整",
"WorkItems": [
"1. ｽﾋﾟｺﾝの調整､下図の回転数でA,B固定｡",
"2. 通常ｽﾋﾟｰﾄﾞで上記ｽﾋﾟｺﾝC,Dで調整｡",
"3. ｴｲｼﾞﾝｸﾞ実施",
"4. 速度切替ﾓｰﾄﾞでの確認｡",
"5. 速度調整後防錆油を塗布する｡"
],
"WorkPoints": [
"2000回動作実施",
"ｴｰｼﾞﾝｸﾞ2000回実施後確認する",
... | {
"QualityItem": "ｽﾋﾟｺﾝ回転量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "上昇時:全開下降時:全閉より2.5回転開ける事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整",
"WorkItems": [
"1. ｽﾋﾟｺﾝの調整､下図の回転数でA,B固定｡",
"2. 通常ｽﾋﾟｰﾄﾞで上記ｽﾋﾟｺﾝC,Dで調整｡",
"3. ｴｲｼﾞﾝｸﾞ実施",
"4. 速度切替ﾓｰﾄﾞでの確認｡",
"5. 速度調整後防錆油を塗布する｡"
],
"WorkPoints": [
"2000回動作実施",
"ｴｰｼﾞﾝｸﾞ20... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "【通常ｽﾋﾟｰﾄﾞ】上昇時:1.30~1.40s下降時:1.45~1.55s【速度切替ﾓｰﾄﾞ】上昇時:0.25~0.45s下降時:1.20~1.40s1.25~1.45s",
"Method": "ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "上下ｽﾋﾟｰﾄﾞ調整",
"WorkItems": [
"1. ｽﾋﾟｺﾝの調整､下図の回転数でA,B固定｡",
"2. 通常ｽﾋﾟｰﾄﾞで上記ｽﾋﾟｺﾝC,Dで調整｡",
"3. ｴｲｼﾞﾝｸﾞ実施",
"4. 速度切替ﾓｰﾄﾞでの確認｡",
"5. 速度調整後防錆油を塗布する｡"
],
"WorkPoints": [
"2000回動作実施",
"ｴｰｼﾞﾝｸﾞ20... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "【通常ｽﾋﾟｰﾄﾞ】上昇時:1.30~1.40s下降時:1.45~1.55s【速度切替ﾓｰﾄﾞ】上昇時:0.25~0.45s下降時:1.20~1.40s1.25~1.45s",
"Method": "ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "WDQB-F013-010",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "P613ﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. にCOVER をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "製造手配銘板の貼付",
"WorkItems": [
"1. のｾﾝｻｰﾄﾞｸﾞに①を貼付ける"
],
"WorkPoints": [
"脱脂後取付けの事",
"端面合わせ",
"QRｺｰﾄﾞを上にする",
"3㎜",
"①から､若い数値の製造番号で貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"Inspectio... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "製造手配銘板の貼付",
"WorkItems": [
"1. のｾﾝｻｰﾄﾞｸﾞに①を貼付ける"
],
"WorkPoints": [
"脱脂後取付けの事",
"端面合わせ",
"QRｺｰﾄﾞを上にする",
"3㎜",
"①から､若い数値の製造番号で貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに貼付けてある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "P606銘板貼付",
"WorkItems": [
"1. COVER にSEAL を貼付ける"
],
"WorkPoints": [
"脱脂後取付けの事",
"各ﾚｰﾝ毎に貼付位置と方向が異なるので注意",
"完成後ｽﾙｰ部品(ﾕﾆｯﾄ付属品)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに貼付けてある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "付属品の準備及びﾁｪｯｸ",
"WorkItems": [
"1. 付属品の準備とﾁｪｯｸ"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"各2(計4)",
"1120㎜×21620㎜×2",
"配管Ф6(黒)",
"準備",
"P001",
"PI... | {
"QualityItem": "準備確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに準備してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ運搬治具",
"Size": "",
"ToolOther": "FM-3168",
"WorkName": "ﾕﾆｯﾄ積み降ろし移動時の注意",
"WorkItems": [
"◆1. ﾕﾆｯﾄ移動時の注意",
"2. ﾍﾞｰｽﾌﾟﾚｰﾄに治具を取付ける"
],
"WorkPoints": [
"必ずFM-3168使用し移動させる事",
"ﾍﾞｰｽﾌﾟﾚｰﾄに治具ｼｬﾌﾄをねじ込んで使用する",
"取手をつかみﾕﾆｯﾄを移動させる"
],
"Tolks": [],
"Inspect... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3168",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.5N･m",
"WorkName": "ｽﾄｯﾊﾟｰ組立",
"WorkItems": [
"1. PLATE PLATE に砥石をかける",
"2. PLATE にSTOPPER をSPACER BOLT WASHER で取付ける(4ヶ作成)",
"4. 2･3完成品を①に㉒BOLT で取付ける"
],
"WorkPoints": [
"ﾀｯﾌﾟ穴があいている面に実施する",
"ﾀｯﾌﾟ3ヶの面にはｽﾄｯﾊﾟｰを取付けないこと",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾄｯﾊﾟｰ組立",
"WorkItems": [
"1. PLATE PLATE に砥石をかける",
"2. PLATE にSTOPPER をSPACER BOLT WASHER で取付ける(4ヶ作成)",
"3. PLATE にSTOPPER をSPACER BOLT WASHER で取付ける(4ヶ作成)",
"4. 2･3完成品を①に㉒BOLT で取付ける"
],
"WorkPoints": [
"ﾀｯﾌﾟ穴が... | {
"QualityItem": "拭取り確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに拭取りしている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽ",
"WorkName": "ﾚﾊﾞｰ組立1",
"WorkItems": [
"3. LEVER にBUSH を圧入",
"◆2. BUSH WASHER にｸﾞﾘｰｽを塗布",
"1. LEVER に砥石をかけ防錆油を全体に塗布する",
"4. 3完成品にWASHER を挿入"
],
"WorkPoints": [
"樹脂層側",
"LEVER のﾋﾟﾝの部分にWASHER の穴を合わせ樹脂層全体が見えるように取付",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2小豆粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "防錆油",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚﾊﾞｰ組立1",
"WorkItems": [
"3. LEVER にBUSH を圧入",
"◆2. BUSH WASHER にｸﾞﾘｰｽを塗布",
"1. LEVER に砥石をかけ防錆油を全体に塗布する",
"4. 3完成品にWASHER を挿入"
],
"WorkPoints": [
"樹脂層側",
"LEVER のﾋﾟﾝの部分にWASHER の穴を合わせ樹脂層全体が見えるように取付",
"ｸ... | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り塗布してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｴﾊﾞｰｽ",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "台車取付部ﾒﾀﾙ圧入治具",
"Size": "",
"ToolOther": "FM-2144",
"WorkName": "ﾚﾊﾞｰ組立1",
"WorkItems": [
"3. LEVER にBUSH を圧入",
"◆2. BUSH WASHER にｸﾞﾘｰｽを塗布",
"1. LEVER に砥石をかけ防錆油を全体に塗布する"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2144",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部ﾚﾊﾞｰ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6510",
"WorkName": "ﾚﾊﾞｰ組立1",
"WorkItems": [
"3. LEVER にBUSH を圧入",
"◆2. BUSH WASHER にｸﾞﾘｰｽを塗布",
"1. LEVER に砥石をかけ防錆油を全体に塗布する"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布位置"
],
"Tolks": [],
"InspectionNo": "",
"Inspection... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6510",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚﾊﾞｰ組立2",
"WorkItems": [
"3. LEVER にBUSH を圧入",
"◆2. BUSH WASHER にｸﾞﾘｰｽを塗布",
"1. LEVER に砥石をかけ防錆油を全体に塗布する"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽ",
"WorkName": "ﾚﾊﾞｰ組立2",
"WorkItems": [
"1. LEVER に砥石をかける",
"◆2. BUSH にｸﾞﾘｰｽを塗布する",
"4. 3完成品にBOLT を取付ける",
"3. 1完成品に2完成品を圧入する"
],
"WorkPoints": [
"塗布位置",
"継ぎ目位置"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"Inspect... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "台車取付部ﾒﾀﾙ圧入治具",
"Size": "",
"ToolOther": "FM-2144",
"WorkName": "ﾚﾊﾞｰ組立2",
"WorkItems": [
"◆2. BUSH にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"塗布位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2144",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾚﾊﾞｰ組立2",
"WorkItems": [
"4. 3完成品にBOLT を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"◆作業者安全作業",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "A003ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. LEVER に砥石をかける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "A003ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [],
"WorkPoints": [
"当付け",
"ﾅｯﾄの向きに注意すること"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 12.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"5㎜"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "A003ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [],
"WorkPoints": [
"当付け",
"ﾅｯﾄの向きに注意すること"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 12.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"5㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:端面より5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "13㎜",
"ToolOther": "12.0N･m",
"WorkName": "A003ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [],
"WorkPoints": [
"当付け",
"ﾅｯﾄの向きに注意すること"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 12.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"5㎜"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "12.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼﾘﾝﾀﾞｰ組立",
"WorkItems": [
"3. 2完成品に②を③で取付ける",
"4. 3完成品にROD-END をNUT で仮に取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 25.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"20㎜",
"仮... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法20㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "8㎜",
"ToolOther": "25.0N･m",
"WorkName": "ｼﾘﾝﾀﾞｰ組立",
"WorkItems": [
"3. 2完成品に②を③で取付ける",
"4. 3完成品にROD-END をNUT で仮に取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 25.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"20㎜",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "25.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "14㎜",
"ToolOther": "10.0N･m",
"WorkName": "ｼﾘﾝﾀﾞｰ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｯﾄﾞｴﾝﾄﾞ寸法出し治具",
"Size": "",
"ToolOther": "FM-2906",
"WorkName": "ｺﾈｸﾃｨﾝｸﾞﾛｯﾄﾞ長さ調整",
"WorkItems": [
"1. のﾛｯﾄﾞ長さを調整する"
],
"WorkPoints": [
"･ｽﾊﾟﾅを手前に回すとﾛｯﾄﾞｴﾝﾄﾞが縮む･奥へ押しながら回すと伸びる方向になる",
"1.0mmが通り1.1mmが通ら無い事",
"調整を行う前に必ずｴｱｰ供給治具よりｴｱｰを入れておく事"
],
"Tolks": [],
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2906",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "1.0㎜",
"ToolOther": "",
"WorkName": "ｺﾈｸﾃｨﾝｸﾞﾛｯﾄﾞ長さ調整",
"WorkItems": [
"1. のﾛｯﾄﾞ長さを調整する"
],
"WorkPoints": [
"･ｽﾊﾟﾅを手前に回すとﾛｯﾄﾞｴﾝﾄﾞが縮む･奥へ押しながら回すと伸びる方向になる",
"1.0mmが通り1.1mmが通ら無い事",
"調整を行う前に必ずｴｱｰ供給治具よりｴｱｰを入れておく事"
],
"Tolks": [],
"Inspect... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "1.0㎜が通るように調整する事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "1.0㎜",
"ToolOther": "",
"WorkName": "ｺﾈｸﾃｨﾝｸﾞﾛｯﾄﾞ長さ調整",
"WorkItems": [
"1. のﾛｯﾄﾞ長さを調整する"
],
"WorkPoints": [
"･ｽﾊﾟﾅを手前に回すとﾛｯﾄﾞｴﾝﾄﾞが縮む･奥へ押しながら回すと伸びる方向になる",
"1.0mmが通り1.1mmが通ら無い事",
"調整を行う前に必ずｴｱｰ供給治具よりｴｱｰを入れておく事"
],
"Tolks": [],
"Inspect... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "1.1㎜が通らないように調整する事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱｰ供給治具",
"Size": "",
"ToolOther": "FM-2446",
"WorkName": "ｺﾈｸﾃｨﾝｸﾞﾛｯﾄﾞ長さ調整",
"WorkItems": [
"1. のﾛｯﾄﾞ長さを調整する"
],
"WorkPoints": [
"･ｽﾊﾟﾅを手前に回すとﾛｯﾄﾞｴﾝﾄﾞが縮む･奥へ押しながら回すと伸びる方向になる",
"1.0mmが通り1.1mmが通ら無い事",
"調整を行う前に必ずｴｱｰ供給治具よりｴｱｰを入れておく事"
],
"Tolks": [],
"Inspect... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2375",
"WorkName": "ｼﾘﾝﾀﾞｰ組立(ﾘｰﾄﾞｽｲｯﾁ取付け)",
"WorkItems": [],
"WorkPoints": [
"41㎜",
"取付け位置:42㎜±0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-2375",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "設定幅時にｾﾝｻがONする事",
"Method": "PHﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｯﾄﾞｴﾝﾄﾞ寸法出し治具",
"Size": "",
"ToolOther": "FM-2906",
"WorkName": "ｼﾘﾝﾀﾞｰ組立(ﾘｰﾄﾞｽｲｯﾁ取付け)",
"WorkItems": [],
"WorkPoints": [
"41㎜",
"取付け位置:42㎜±0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "FM-2906",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.6㎜(ﾏｲﾅｽ)",
"ToolOther": "10cN･m",
"WorkName": "ｼﾘﾝﾀﾞｰ組立(ﾘｰﾄﾞｽｲｯﾁ取付け)",
"WorkItems": [],
"WorkPoints": [
"41㎜",
"取付け位置:42㎜±0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼﾘﾝﾀﾞｰ組立(ﾘｰﾄﾞｽｲｯﾁ取付け)",
"WorkItems": [],
"WorkPoints": [
"41㎜",
"取付け位置:42㎜±0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に取付けてある事指示寸法41㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱｰ供給治具",
"Size": "",
"ToolOther": "FM-2446",
"WorkName": "ｼﾘﾝﾀﾞｰ組立(ﾘｰﾄﾞｽｲｯﾁ取付け)",
"WorkItems": [],
"WorkPoints": [
"41㎜",
"取付け位置:42㎜±0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け",
"WorkItems": [
"1. PLATE に⑤LABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"70㎜",
"55㎜",
"115㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "側面ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. にPOST をBOLT WASHER で取付ける"
],
"WorkPoints": [
"Hｶｯﾄの方向",
"Hｶｯﾄの方向"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "側面ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"3. 2完成品にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "5.3N･m",
"WorkName": "側面ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"2. 1完成品にPOST をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.3N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "55cN･m",
"WorkName": "ｽｲｯﾁ配線接続",
"WorkItems": [
"■1. SWITCH の型式確認をし､ﾛｯﾄNo.を記録する",
"2. SWITCH のｽｲｯﾁﾚﾊﾞｰを組替える",
"■3. 2完成品にJOINT を取付し､③の配線を接続する"
],
"WorkPoints": [
"ﾚﾊﾞｰは反転させ取付ける",
"配線をJOINTに通す",
"先端部を取外し時計回りに90度向き... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "55cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "170cN･m",
"WorkName": "ｽｲｯﾁ配線接続",
"WorkItems": [
"■1. SWITCH の型式確認をし､ﾛｯﾄNo.を記録する",
"2. SWITCH のｽｲｯﾁﾚﾊﾞｰを組替える",
"■3. 2完成品にJOINT を取付し､③の配線を接続する"
],
"WorkPoints": [
"ﾚﾊﾞｰは反転させ取付ける",
"配線をJOINTに通す",
"先端部を取外し時計回りに90度向... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "170cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "70cN･m",
"WorkName": "ｽｲｯﾁ配線接続",
"WorkItems": [],
"WorkPoints": [
"ﾚﾊﾞｰ部組替え後必ず動作確認を行うﾚﾊﾞｰを動作させ､引っかかりが無い事",
"JOINTを締込み配線を固定する",
"ｶﾊﾞｰを閉じﾈｼﾞを締結する",
"ｶﾊﾞｰを開け端子をﾗﾍﾞﾙと同じ箇所に接続する"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "70cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "60cN･m",
"WorkName": "ｽｲｯﾁ配線接続",
"WorkItems": [],
"WorkPoints": [
"ﾚﾊﾞｰ部組替え後必ず動作確認を行うﾚﾊﾞｰを動作させ､引っかかりが無い事",
"JOINTを締込み配線を固定する",
"ｶﾊﾞｰを閉じﾈｼﾞを締結する",
"ｶﾊﾞｰを開け端子をﾗﾍﾞﾙと同じ箇所に接続する"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "",
"ToolOther": "",
"WorkName": "ｽｲｯﾁ配線接続",
"WorkItems": [
"■1. SWITCH の型式確認をし､ﾛｯﾄNo.を記録する",
"2. SWITCH のｽｲｯﾁﾚﾊﾞｰを組替える",
"■3. 2完成品にJOINT を取付し､③の配線を接続する"
],
"WorkPoints": [
"ﾚﾊﾞｰは反転させ取付ける",
"ﾚﾊﾞｰ部組替え後必ず動作確認を行うﾚﾊﾞｰを動作させ､引っかかりが無い事",
"JOIN... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "",
"ToolOther": "",
"WorkName": "ｽｲｯﾁ配線接続",
"WorkItems": [
"■1. SWITCH の型式確認をし､ﾛｯﾄNo.を記録する",
"2. SWITCH のｽｲｯﾁﾚﾊﾞｰを組替える",
"■3. 2完成品にJOINT を取付し､③の配線を接続する"
],
"WorkPoints": [
"ﾚﾊﾞｰは反転させ取付ける",
"ﾚﾊﾞｰ部組替え後必ず動作確認を行うﾚﾊﾞｰを動作させ､引っかかりが無い事",
"JOIN... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽｲｯﾁ配線接続",
"WorkItems": [
"■1. SWITCH の型式確認をし､ﾛｯﾄNo.を記録する",
"2. SWITCH のｽｲｯﾁﾚﾊﾞｰを組替える",
"■3. 2完成品にJOINT を取付し､③の配線を接続する"
],
"WorkPoints": [
"ﾚﾊﾞｰは反転させ取付ける",
"ﾚﾊﾞｰ部組替え後必ず動作確認を行うﾚﾊﾞｰを動作させ､引っかかりが無い事",
"JOINTを締込み配... | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C17",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽｲｯﾁ配線接続",
"WorkItems": [
"■1. SWITCH の型式確認をし､ﾛｯﾄNo.を記録する",
"2. SWITCH のｽｲｯﾁﾚﾊﾞｰを組替える",
"■3. 2完成品にJOINT を取付し､③の配線を接続する"
],
"WorkPoints": [
"ﾚﾊﾞｰは反転させ取付ける",
"ﾚﾊﾞｰ部組替え後必ず動作確認を行うﾚﾊﾞｰを動作させ､引っかかりが無い事",
"JOINTを締込み配... | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "検査表の有無を確認する事",
"Method": "目視",
"RecordMethod": "WETE-G002-C17",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "150cN･m",
"WorkName": "ｽｲｯﾁﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. PLATE に のSWをBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄに対し平行に取付けの事(面位置)"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "8㎜",
"ToolOther": "40N･m",
"WorkName": "駆動部組立1",
"WorkItems": [],
"WorkPoints": [
"治具ﾎﾞﾙﾄ(M10×35)",
"PINに挿入"
],
"Tolks": [
"締付ﾄﾙｸ 40N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部置台(NPM-GW17)",
"Size": "",
"ToolOther": "FM-6422",
"WorkName": "駆動部組立1",
"WorkItems": [
"1. に をBOLT WASHER で仮に取付ける",
"2. 1完成品にｽﾀﾝﾄﾞ治具に取付ける"
],
"WorkPoints": [
"治具ﾎﾞﾙﾄ(M10×35)",
"PINに挿入"
],
"Tolks": [
"締付ﾄﾙｸ 40N･m"
],
"InspectionNo": "",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6422",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "交換台車駆動部置台(NPM-GW17)",
"Size": "",
"ToolOther": "FM-6422",
"WorkName": "駆動部組立2",
"WorkItems": [
"1. に治具を仮に取付ける",
"2. 1完成品に治具ﾋﾟﾝ(Φ3.99)を入れる"
],
"WorkPoints": [
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6422",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "台車駆動鋳物との位置決めｼﾞｸﾞ(17連右側)",
"Size": "",
"ToolOther": "FM-6421",
"WorkName": "駆動部組立2",
"WorkItems": [
"1. に治具を仮に取付ける",
"2. 1完成品に治具ﾋﾟﾝ(Φ3.99)を入れる"
],
"WorkPoints": [
"ｽﾀﾝﾄﾞ治具に取付状態ですが削除しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6421",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.