input stringclasses 1
value | instruction stringlengths 202 3.29k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾌﾞﾗｹｯﾄ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5086",
"WorkName": "ﾌﾚｰﾑ組立5",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"中段",
"下段",
"下段",
"中段",
"0.1㎜が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"Inspect... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5086",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立5",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"中段",
"下段",
"下段",
"中段",
"0.1㎜が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItem... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜ﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C31",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "100cN･m",
"WorkName": "ﾌﾚｰﾑ組立6",
"WorkItems": [
"1. にPLATE をBOLT で取付ける"
],
"WorkPoints": [
"PLATE のPLATEは外側を幅広側にする",
"PLATE の取付前に油砥石で両面のﾊﾞﾘを除去する事"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"Inspec... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "194cN･m",
"WorkName": "保持ﾚｰﾙ取付け",
"WorkItems": [
"1. に をBOLT で取付ける"
],
"WorkPoints": [
"12.1㎜",
"取付け寸法",
"左右のﾏｶﾞｼﾞﾝ保持ﾚｰﾙは固定時下押し当てで固定の事",
"ｽﾗｲﾄﾞﾚｰﾙを動かし取付ける",
"BOLT の丸子ﾈｼﾞは六角穴部が潰れ易いので､摩耗した工具の使用不可"
],
"Tolk... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "12.1㎜",
"ToolOther": "",
"WorkName": "保持ﾚｰﾙ取付け",
"WorkItems": [
"1. に をBOLT で取付ける"
],
"WorkPoints": [
"12.1㎜",
"取付け寸法",
"左右のﾏｶﾞｼﾞﾝ保持ﾚｰﾙは固定時下押し当てで固定の事",
"ｽﾗｲﾄﾞﾚｰﾙを動かし取付ける",
"BOLT の丸子ﾈｼﾞは六角穴部が潰れ易いので､摩耗した工具の使用不可"
],
"Tolks": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "12.1㎜を挟んで取付ける事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C31",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "保持ﾚｰﾙ連結",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"保持ﾚｰﾙは閉じた状態で取付けの事",
"矢印方向に押し当てて固定する｡上段･下段両方行うこと｡固定後､ﾏｶﾞｼﾞﾝを載せｽﾑｰｽﾞな出し入れと収納が出来る事を確認｡"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｶﾞｲﾄﾞﾚｰﾙ取付け",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"K005-1",
"K005-2",
" と の取付位置",
"BRACKETの向きに注意",
"上方向へ押し当てて取付けの事",
"保持ﾚｰﾙ部に干渉してい無い事"
],
"Tolks": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｼｬｯﾀｰ開閉ｽﾄｯﾊﾟｰ・ｾｯﾄｸﾗﾝﾌﾟ取付け",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"矢印方向に押し当てて取付けの事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM5519",
"WorkName": "ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"WorkItems": [
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"1. に㉖をﾏｶﾞｼﾞﾝ保持部上段に取付ける",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け、上段と同様に調整する",
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"1. に㉖をﾏｶﾞｼﾞﾝ保持部上段に取付ける",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付... | {
"QualityItem": "設置確認",
"ToolManageNo": "FM5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設置出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "治具ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"WorkItems": [
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"1. に㉖をﾏｶﾞｼﾞﾝ保持部上段に取付ける",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け、上段と同様に調整する",
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"1. に㉖をﾏｶﾞｼﾞﾝ保持部上段に取付ける",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け、上段と同様... | {
"QualityItem": "設置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設置出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.2㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"WorkItems": [
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"1. に㉖をﾏｶﾞｼﾞﾝ保持部上段に取付ける",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け、上段と同様に調整する",
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"1. に㉖をﾏｶﾞｼﾞﾝ保持部上段に取付ける",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.2㎜ﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C31",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.2㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"WorkItems": [
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"1. に㉖をﾏｶﾞｼﾞﾝ保持部上段に取付ける",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け、上段と同様に調整する",
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"1. に㉖をﾏｶﾞｼﾞﾝ保持部上段に取付ける",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.25㎜ﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C31",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"WorkItems": [
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"1. に㉖をﾏｶﾞｼﾞﾝ保持部上段に取付ける",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け、上段と同様に調整する",
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"1. に㉖をﾏｶﾞｼﾞﾝ保持部上段に取付ける",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "治具ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整",
"WorkItems": [
"3. 下段側も同様に調整する"
],
"WorkPoints": [
"ﾏｶﾞｼﾞﾝﾒｶｽﾄｯﾊﾟｰ",
"ﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰ",
"押し当て固定",
"ｼｯｸﾈｽｹﾞｰｼﾞ:0.1㎜",
"ﾏｶﾞｼﾞﾝﾒｶｽﾄｯﾊﾟｰ",
"ﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰ",
"押し当て固定",
"ｼｯｸﾈｽｹﾞｰｼﾞ... | {
"QualityItem": "設置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設置出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整",
"WorkItems": [
"3. 下段側も同様に調整する"
],
"WorkPoints": [
"ﾏｶﾞｼﾞﾝﾒｶｽﾄｯﾊﾟｰ",
"ﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰ",
"押し当て固定",
"ｼｯｸﾈｽｹﾞｰｼﾞ:0.1㎜",
"ﾏｶﾞｼﾞﾝﾒｶｽﾄｯﾊﾟｰ",
"ﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰ",
"押し当て固定",
"ｼｯｸﾈ... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定の位置に0.1㎜を挟む",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整",
"WorkItems": [
"3. 下段側も同様に調整する"
],
"WorkPoints": [
"ﾏｶﾞｼﾞﾝﾒｶｽﾄｯﾊﾟｰ",
"ﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰ",
"押し当て固定",
"ｼｯｸﾈｽｹﾞｰｼﾞ:0.1㎜",
"ﾏｶﾞｼﾞﾝﾒｶｽﾄｯﾊﾟｰ",
"ﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰ",
"押し当て固定",
"ｼｯｸﾈ... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜ﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C31",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "3.6㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整",
"WorkItems": [
"3. 下段側も同様に調整する"
],
"WorkPoints": [
"ﾏｶﾞｼﾞﾝﾒｶｽﾄｯﾊﾟｰ",
"ﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰ",
"押し当て固定",
"ｼｯｸﾈｽｹﾞｰｼﾞ:0.1㎜",
"ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟ",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ:3.6㎜",
"ｼｯｸﾈｽｹﾞｰｼﾞ:0.05㎜"
... | {
"QualityItem": "設置確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り設置出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整",
"WorkItems": [
"3. 下段側も同様に調整する"
],
"WorkPoints": [
"ﾏｶﾞｼﾞﾝﾒｶｽﾄｯﾊﾟｰ",
"ﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰ",
"押し当て固定",
"ｼｯｸﾈｽｹﾞｰｼﾞ:0.1㎜",
"ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟ",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ:3.6㎜",
"ｼｯｸﾈｽｹﾞｰｼﾞ:0.05... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "扉開閉ﾊﾞﾙﾌﾞ・扉ﾛｯｸｼﾘﾝﾀﾞｰ取付け",
"WorkItems": [],
"WorkPoints": [
"SD-A041086-405にて本締結実施"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "194cN･m",
"WorkName": "ｺﾈｸﾀﾌﾞﾗｹｯﾄ・安全SW取付け",
"WorkItems": [],
"WorkPoints": [
"矢印方向に押し当て取付けの事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾊﾞｰ用POST取付け",
"WorkItems": [
"1. にPOST をBOLT WASHER で仮取付けする",
"2. 1完成品にPOST をBOLT WASHER で仮取付けする"
],
"WorkPoints": [
"Hｶｯﾄ部を縦方向に固定する｡POST POST の長さが違うので取付位置に注意",
"Hｶｯﾄ部を縦方向に固定する｡POST POST の長さが違うので取付位置に注意",
"SD-A0... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "扉用ﾏｸﾞﾈｯﾄ・ｷｬｯﾁ取付け",
"WorkItems": [
"1. に をPLATE BOLT WASHER で仮取付けする",
"2. 1完成品に をWASHER BOLT で仮取付けする"
],
"WorkPoints": [
"矢印方向へ押し当てて仮固定する",
"矢印方向へ押し当てて仮固定する",
"SD-A041086-403にて本締結実施",
"SD-A041086-404にて本締結実施"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FT4取付け",
"WorkItems": [
"1. にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"右側面",
"ｲﾝｼｭﾛｯｸ挿入方向を下図参照に向ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "連結用ﾌﾞﾗｹｯﾄ・ｶﾞｲﾄﾞﾌﾞﾛｯｸ取付け",
"WorkItems": [],
"WorkPoints": [
"右側",
"右側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾏｶﾞｼﾞﾝ保持部ﾌﾞﾗｹｯﾄ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5216",
"WorkName": "連結用ﾌﾞﾗｹｯﾄ・ｶﾞｲﾄﾞﾌﾞﾛｯｸ取付け",
"WorkItems": [
"1. にBRACKET を左右上部にBOLT WASHER で取付ける",
"2. 1完成品にBLOCK をSPACER BOLT WASHER で取付ける"
],
"WorkPoints": [
"左側",
"右側",
"BRACKET を仮取付け後､治具FM-5216に押し当て... | {
"QualityItem": "設置確認",
"ToolManageNo": "FM-5216",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設置出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｹｰﾌﾞﾙﾍﾞｱﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ｹｰﾌﾞﾙﾍﾞｱﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"2. 1完成品にJOINT をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｴｱｰ配管接続",
"WorkItems": [
"1. JOINT にJOINT を挿入する",
"2. TUBE を指定の長さにｶｯﾄし､1完成品に挿入する",
"3. 2完成品を に挿入する"
],
"WorkPoints": [
"100㎜",
"70㎜",
"外側よりﾀﾞﾌﾞﾙｿﾚﾉｲﾄﾞとｼﾝｸﾞﾙｿﾚﾉｲﾄﾞに短い方を各1本ずつ､一番内側のｼﾝｸﾞﾙｿﾚﾉｲﾄﾞに長いﾁｭｰﾌﾞを挿入す... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｴｱｰ配管接続",
"WorkItems": [
"1. JOINT にJOINT を挿入する",
"2. TUBE を指定の長さにｶｯﾄし､1完成品に挿入する",
"3. 2完成品を に挿入する"
],
"WorkPoints": [
"100㎜",
"70㎜",
"外側よりﾀﾞﾌﾞﾙｿﾚﾉｲﾄﾞとｼﾝｸﾞﾙｿﾚﾉｲﾄﾞに短い方を各1本ずつ､一番内側のｼﾝｸﾞﾙｿﾚﾉｲﾄﾞに長いﾁｭｰﾌﾞを挿入する｡"
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾛﾝﾄﾌﾚｰﾑﾋﾟﾝ圧入ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4882",
"WorkName": "YZﾋﾟﾝ圧入",
"WorkItems": [
"1. FRAME(A) にPIN を圧入する",
"2. PIN をSCREW を固定する"
],
"WorkPoints": [
"圧入前､FRAME(A) 下面に砥石を掛けておく"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4882",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "50cN･m",
"WorkName": "YZﾋﾟﾝ圧入",
"WorkItems": [
"1. FRAME(A) にPIN を圧入する",
"2. PIN をSCREW を固定する"
],
"WorkPoints": [
"圧入前､FRAME(A) 下面に砥石を掛けておく"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionIt... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X位置決めﾋﾟﾝ取付",
"WorkItems": [
"1. にPIN をNUT WASHER で仮止めする"
],
"WorkPoints": [
"｢SD-A000501-306｣で本締め",
"ﾏｲﾅｽの溝を横方向にしておく"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ALﾌﾛﾝﾄﾌﾚｰﾑPIN圧入治具",
"Size": "",
"ToolOther": "FM-4421",
"WorkName": "Fﾌﾚｰﾑﾋﾟﾝ圧入",
"WorkItems": [
"1. にPIN を圧入する"
],
"WorkPoints": [
"ﾋﾟﾝ出代:3.5㎜ 治具より高く出ていないこと",
"PIN の細いほうを 側に圧入",
"ﾌﾚｰﾑ下面に突き出ないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "PIN出代",
"ToolManageNo": "FM-4421",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.5㎜",
"Method": "目視手感",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ALﾘｱﾌﾚｰﾑPIN圧入治具",
"Size": "",
"ToolOther": "FM-4422",
"WorkName": "Rﾌﾚｰﾑﾋﾟﾝ圧入",
"WorkItems": [
"1. FRAME(B) にPIN PIN を圧入する"
],
"WorkPoints": [
"治具をｾｯﾄしてﾋﾟﾝを入れる",
"上から治具を被せて圧入する",
"ﾋﾟﾝ出代:3.0㎜下側治具より高く出ていないこと",
"PIN の細いほうをFRAME(B) 側に圧入",
"PIN の引っ掛け側を上側に圧入",... | {
"QualityItem": "PIN出代",
"ToolManageNo": "FM-4422",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.2㎜出代:3.0㎜",
"Method": "目視手感",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ALﾘｱﾌﾚｰﾑPIN圧入治具",
"Size": "",
"ToolOther": "FM-4423",
"WorkName": "Rﾌﾚｰﾑﾋﾟﾝ取付け",
"WorkItems": [
"1. にPIN を圧入する"
],
"WorkPoints": [
"突き当たりまで圧入する",
" に治具を取付ける",
"PIN の上に治具を乗せて圧入する",
"青い穴にPIN を入れる",
"PIN の引っ掛け側を上側に圧入",
"㉗のピンを丸位置に挿入"
],
"Tolks": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4423",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝ圧入治具",
"Size": "",
"ToolOther": "FM-3913",
"WorkName": "Tｽﾛｯﾄﾋﾟﾝ圧入",
"WorkItems": [
"4. PIN を入れて圧入する"
],
"WorkPoints": [
"RAIL の斜めに加工している側を作業者側から見て右になるようにｾｯﾄする",
"PIN の細いほうを➀側に圧入"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
... | {
"QualityItem": "PIN出代方向確認",
"ToolManageNo": "FM-3913",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:1.8㎜",
"Method": "目視手感",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞｱﾘﾝｸﾞ圧入治具",
"Size": "",
"ToolOther": "FM-4105",
"WorkName": "ﾍﾞｱﾘﾝｸﾞ圧入1",
"WorkItems": [
"1. STOPPER にBEARING orBEARING とBEARING を圧入する"
],
"WorkPoints": [
"治具にSTOPPER を乗せる",
"STOPPER にBEARING ･BEARING を乗せる",
"BEARING ･BEARING の上に治具を被せて圧入する",
"BEARING ･BEARI... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4105",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "box4㎜",
"ToolOther": "20cN･m",
"WorkName": "ﾚﾊﾞｰ組立",
"WorkItems": [
"1. PIN を治具に乗せて､ WASHER LEVER の順で乗せていきNUT で固定する"
],
"WorkPoints": [
"治具にPIN を入れる",
"PIN の上に を乗せる",
" の上にWASHER を乗せる",
"WASHER の上にLEVER を乗せる",
"NUT を乗せて固定する"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾚﾊﾞｰ部組立治具",
"Size": "",
"ToolOther": "FM-4399",
"WorkName": "ﾚﾊﾞｰ組立",
"WorkItems": [
"1. PIN を治具に乗せて､ WASHER LEVER の順で乗せていきNUT で固定する"
],
"WorkPoints": [
"治具にPIN を入れる",
"PIN の上に を乗せる",
" の上にWASHER を乗せる",
"WASHER の上にLEVER を乗せる",
"NUT を乗せて固定する"
],
"To... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4399",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞｱﾘﾝｸﾞ圧入治具",
"Size": "",
"ToolOther": "FM-4398",
"WorkName": "ﾍﾞｱﾘﾝｸﾞ圧入2",
"WorkItems": [
"1. LEVER にBEARING orBEARING を圧入する"
],
"WorkPoints": [
"LEVER とBEARING の端面を合わせる",
"この面よりﾍﾞｱﾘﾝｸﾞがはみ出していないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4398",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾎｲｰﾙ組立台",
"Size": "",
"ToolOther": "FM-4407",
"WorkName": "落下防止ｷﾞｱ組立1",
"WorkItems": [
"1. WHEEL にCLUTCH を圧入する",
"2. 上記完成品にWHEEL をSCREW で取付ける"
],
"WorkPoints": [
"圧入する",
"ｼﾞｸﾞにWHEEL を乗せる",
"回転方向の矢印が見える様にCLUTCH を置く",
"WHEEL の凸部とCLUTCH の凹部の位置合わせをする",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4407",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "\u002B№1",
"ToolOther": "15cN･m",
"WorkName": "落下防止ｷﾞｱ組立1",
"WorkItems": [
"2. 上記完成品にWHEEL をSCREW で取付ける"
],
"WorkPoints": [
"樹脂の凸部とWHEEL の穴を合わせる事",
"ﾈｼﾞが届かない場合は治具上で作業する事",
"WHEEL は表裏あり",
"CLUTCH は表裏あり"
],
"Tolks": [
"締付ﾄﾙｸ 15c... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "60cN･m",
"WorkName": "落下防止ｷﾞｱ組立2",
"WorkItems": [
"1. ㉗（右側）にPIN BRACKET の順番で下記写真のようにセットし、SCREW で締結する",
"2. ㉗（左側）に上記完成品、 、COLLAR の順番でセットし、SCREW で締結し、CAP を取付ける"
],
"WorkPoints": [
"PIN の凹部を上向きにｾｯﾄする",
"BRACKET の凸部にPIN の凹部が乗... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "落下防止ｷﾞｱ組立2",
"WorkItems": [
"1. ㉗（右側）にPIN BRACKET の順番で下記写真のようにセットし、SCREW で締結する",
"2. ㉗（左側）に上記完成品、 、COLLAR の順番でセットし、SCREW で締結し、CAP を取付ける"
],
"WorkPoints": [
"PIN の凹部を上向きにｾｯﾄする",
"回転方向",
" ,COLLAR を写真の向きでｾｯﾄする事",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃｰﾌﾟ落下防止ｷﾞｱ組立台",
"Size": "",
"ToolOther": "FM-5587",
"WorkName": "落下防止ｷﾞｱ組立2",
"WorkItems": [
"1. ㉗（右側）にPIN BRACKET の順番で下記写真のようにセットし、SCREW で締結する",
"2. ㉗（左側）に上記完成品、 、COLLAR の順番でセットし、SCREW で締結し、CAP を取付ける"
],
"WorkPoints": [
"PIN の凹部を上向きにｾｯﾄする",
"BRACKET の凸部にPIN の凹部が... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5587",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾏｲﾅｽ幅7㎜",
"ToolOther": "40cN･m",
"WorkName": "ﾃｰﾌﾟｶﾞｲﾄﾞ押さえﾚﾊﾞｰ組立",
"WorkItems": [
"1. 治具にSPACER を乗せ､LEVER WASHER BEARING orBEARING を置いてPIN で固定する",
"2. 上記完成品にPLATE をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 15cN･m"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃｰﾌﾟ押えﾚﾊﾞｰ部組立治具",
"Size": "",
"ToolOther": "FM-4403",
"WorkName": "ﾃｰﾌﾟｶﾞｲﾄﾞ押さえﾚﾊﾞｰ組立",
"WorkItems": [
"1. 治具にSPACER を乗せ､LEVER WASHER BEARING orBEARING を置いてPIN で固定する",
"2. 上記完成品にPLATE をSCREW で取付ける",
"1. 治具にSPACER を乗せ､LEVER WASHER BEARING orBEARING を置いてPIN で固定する",
"2. 上記... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4403",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾏｲﾅｽ幅7㎜",
"ToolOther": "40cN･m",
"WorkName": "ﾃｰﾌﾟｶﾞｲﾄﾞ押さえﾚﾊﾞｰ組立",
"WorkItems": [
"1. 治具にSPACER を乗せ､LEVER WASHER BEARING orBEARING を置いてPIN で固定する",
"2. 上記完成品にPLATE をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 15cN･m"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "\u002B№0",
"ToolOther": "22cN･m",
"WorkName": "ｱｸﾁｭｴｰﾀｰ組立",
"WorkItems": [
"1. SOLENOID-ACTUATOR から先端部のﾋﾟｽﾄﾝを抜いておく",
"3. 完成品を治具に取付け固定する"
],
"WorkPoints": [
"ﾋﾟｽﾄﾝは取付け時に使用する為廃棄し無い事",
"ｱｸﾁｭｴｰﾀｰの穴とｼﾞｸﾞの凸部とｱｸﾁｭｴｰﾀｰの凸部とｼﾞｸﾞの凹部を合わせる",
"｢SD-A00... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "22cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｱｸﾁｭｴｰﾀ組付治具",
"Size": "",
"ToolOther": "FM-4400",
"WorkName": "ｱｸﾁｭｴｰﾀｰ組立",
"WorkItems": [
"1. SOLENOID-ACTUATOR から先端部のﾋﾟｽﾄﾝを抜いておく",
"3. 完成品を治具に取付け固定する"
],
"WorkPoints": [
"ﾋﾟｽﾄﾝは取付け時に使用する為廃棄し無い事",
"ｱｸﾁｭｴｰﾀｰの穴とｼﾞｸﾞの凸部とｱｸﾁｭｴｰﾀｰの凸部とｼﾞｸﾞの凹部を合わせる",
"｢SD-A000501-5... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4400",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "\u002BNo.0",
"ToolOther": "25cN･m",
"WorkName": "ﾃｰﾌﾟ矯正ｶﾞｲﾄﾞ組立",
"WorkItems": [
"3. 本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 25cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "25cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "矯正ｶﾞｲﾄﾞねじ締めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4781",
"WorkName": "ﾃｰﾌﾟ矯正ｶﾞｲﾄﾞ組立",
"WorkItems": [
"2. 1.完成品を㉘にセットする",
"4. ﾚﾊﾞｰを戻して完成品を取り外す",
"3. 本締めする",
"2. 1.完成品を㉘にセットする",
"4. ﾚﾊﾞｰを戻して完成品を取り外す"
],
"WorkPoints": [
"ｸﾗﾝﾌﾟ部を開いて入れる",
"ﾚﾊﾞｰを倒してｸﾗﾝﾌﾟさせる"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4781",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "中継基盤組立",
"WorkItems": [
"1. LED-LAMP-UNIT のｹｰﾌﾞﾙをBOARD のｺﾈｸﾀに取付ける"
],
"WorkPoints": [
"LED-LAMP-UNIT の挿入方向に注意",
"ｺﾈｸﾀを接続したら青ﾏｰｷﾝｸﾞをする",
"色が薄い部分が､1mm程度出ている"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "\u002B№2",
"ToolOther": "60cN･m",
"WorkName": "ﾃｰﾌﾟ規正ｶﾞｲﾄﾞ組立1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ規正ｶﾞｲﾄﾞ組立1",
"WorkItems": [
"1. ㉘にGUIDE GUIDE ,BRACKET ,PLATE の順番で写真のように置き、SCREW で締結",
"2.上記､完成品を反転させ､PLATE を置き､SCREW にて締結"
],
"WorkPoints": [
"GUIDE :段ありが上",
"GUIDE :向きはどちらでも可",
"㉘を反対の手で押さえながら締結の事"
],
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃｰﾌﾟ規制ｶﾞｲﾄﾞ組立台",
"Size": "",
"ToolOther": "FM-5582",
"WorkName": "ﾃｰﾌﾟ規正ｶﾞｲﾄﾞ組立1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5582",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ規正ｶﾞｲﾄﾞ組立2",
"WorkItems": [
"1. にBOLT NUT を取付ける"
],
"WorkPoints": [
"締め込ま無い事(本締めはSD-A000501-531)",
"目安寸法2~2.5mm",
"ﾅｯﾄ取付け方向図示のこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:2~2.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ規正ｶﾞｲﾄﾞ組立3",
"WorkItems": [
"1. COVER にBLOCK KIT を貼付ける"
],
"WorkPoints": [
"16.5㎜±0.5㎜",
"2㎜±0.5㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:16.5±0.5㎜2±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｻﾐ",
"Size": "小",
"ToolOther": "CANARY:DS-100",
"WorkName": "ﾏｸﾞﾈｯﾄ準備",
"WorkItems": [
"1. MAGNET を㉗で１つずつに切り分ける",
"2. MAGNET MAGNET を㉖で１つずつに切り分ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "切断確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "両面ﾃｰﾌﾟが切れている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾏｸﾞﾈｯﾄ貼付けｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5610",
"WorkName": "ｽﾌﾟﾘﾝｸﾞﾌﾟﾚｰﾄ組立2",
"WorkItems": [
"1. ㉖のブロックを持ち上げてSPRING-PLATE を取付ける。",
"2. SPRING-PLATE に を取付ける｡"
],
"WorkPoints": [
"2段に曲げているほうが左側",
"奥に押し当てる",
"ﾉﾌﾞを回してSPRING-PLATE を規正する",
"左のﾌﾞﾛｯｸに当付け",... | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-5610",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾏｸﾞﾈｯﾄ貼付けｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5610",
"WorkName": "ｽﾌﾟﾘﾝｸﾞﾌﾟﾚｰﾄ組立3",
"WorkItems": [
"1. ㉖のカバーを下す",
"2. ③を貼付ける"
],
"WorkPoints": [
"中のﾏｸﾞﾈｯﾄに当付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-5610",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾏｸﾞﾈｯﾄ貼付けｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5610",
"WorkName": "ｽﾌﾟﾘﾝｸﾞﾌﾟﾚｰﾄ組立4",
"WorkItems": [
"1. ㉖のカバーを上げて、規正を外す",
"2. ﾌﾞﾛｯｸを持ち上げて､ｽﾌﾟﾘﾝｸﾞを外す"
],
"WorkPoints": [
"ﾉﾌﾞを引っ張って回し､規正を解除する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words... | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-5610",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾌﾟﾘﾝｸﾞﾌﾟﾚｰﾄ組立1",
"WorkItems": [
"1. BASE PLATE にSTOPPER-BLOCK を取付ける"
],
"WorkPoints": [
"出っ張りを左右の丸ﾋﾟﾝに引っ掛ける",
"表裏間違えないように取付けのこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"上面... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾏｸﾞﾈｯﾄｷｯﾄ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5589",
"WorkName": "ｽﾌﾟﾘﾝｸﾞﾌﾟﾚｰﾄ組立5",
"WorkItems": [
"2. に を取付ける",
"1. ㉖に をセットする"
],
"WorkPoints": [
" の方向に注意",
"B側",
"A側",
"A側",
"B側",
"両端にしっかり引っ掛かっているか確認",
"2段に曲げているほうがC側",
"D側",
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-5589",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-4865",
"WorkName": "ｱﾀｯﾁﾒﾝﾄ接続部組立",
"WorkItems": [
"1. CABLE を7箇所束線する",
"2. CONNECTOR をCABLE に取付ける"
],
"WorkPoints": [
"※ｺﾈｸﾀ取付方向を合わせること",
"ｽﾀｰﾄ位置",
"茶色部分をｶﾌﾟﾄﾝﾃｰﾌﾟ長さ15mm程度で束線すること",
"※㉗の■の真上を束線すること"
],
"Tolks... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4865",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "30cN･m",
"WorkName": "ﾊﾝﾄﾞﾙ組立",
"WorkItems": [
"1. BRACKET にHANDLE をWASHER BOLT で取付ける"
],
"WorkPoints": [
"取付け穴中央で固定する事"
],
"Tolks": [
"締付ﾄﾙｸ 30cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾝﾄﾞﾙ組立",
"WorkItems": [
"1. BRACKET にHANDLE をWASHER BOLT で取付ける"
],
"WorkPoints": [
"取付け穴中央で固定する事"
],
"Tolks": [
"締付ﾄﾙｸ 30cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "\u002B№1",
"ToolOther": "40cN･m",
"WorkName": "Tｽﾛｯﾄ取付け",
"WorkItems": [
"1. に をSCREW で取付ける"
],
"WorkPoints": [
"指示された順番で固定する事",
"締め付け順番"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "F/Rﾄﾞｯｷﾝｸﾞ1",
"WorkItems": [
"1. と をBOLT で接続する"
],
"WorkPoints": [
"取付前､接合面をｱﾙｶﾝｻｽをかけ定盤上で行う事",
"下記順番通り締結すること"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. にBRACKET をBOLT で取付ける"
],
"WorkPoints": [
"定盤上で矢印方向(定盤面)に押さえ取付けのこと"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "\u002BNo.1",
"ToolOther": "50cN･m",
"WorkName": "誤挿入防止ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. にBRACKET をSCREW で取付ける"
],
"WorkPoints": [
"定盤上で下記のように下･左に押し付けて締結すること"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "誤挿入防止ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. にBRACKET をSCREW で取付ける"
],
"WorkPoints": [
"定盤上で下記のように下･左に押し付けて締結すること"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "F/Rﾄﾞｯｷﾝｸﾞ2",
"WorkItems": [
"1. に㉖を貼付ける",
"2. 台紙を剥がしておく"
],
"WorkPoints": [
"左右:端面合わせ上下:溝の中央",
"左右:端面合わせ上下:端面合わせした面のどこでも可",
"左右:端面合わせ上下:端面合わせ",
"左右:丸い刻印の右側上下:丸い刻印の上側"
],
"Tolks": [],
"InspectionNo"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "100cN･m",
"WorkName": "ﾊﾝﾄﾞﾙ取付け",
"WorkItems": [
"1. に を.BOLT WASHER で取付ける"
],
"WorkPoints": [
"定盤上で組立てを行い､側面を合わせる事"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Rﾌﾚｰﾑ組立1",
"WorkItems": [
"1. にGUIDE をBOLT で取付ける",
"2. にGUIDE をSCREW で取付ける"
],
"WorkPoints": [
"左下に押し当てながら取付けのこと",
"下方向に押し当てて取付"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 20cN･m"
],
"InspectionNo": "... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "40cN･m",
"WorkName": "Rﾌﾚｰﾑ組立1",
"WorkItems": [
"1. にGUIDE をBOLT で取付ける",
"2. にGUIDE をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "\u002BNo.1",
"ToolOther": "20cN･m",
"WorkName": "Rﾌﾚｰﾑ組立1",
"WorkItems": [],
"WorkPoints": [
"左下に押し当てながら取付けのこと",
"下方向に押し当てて取付"
],
"Tolks": [
"締付ﾄﾙｸ 20cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"下方向に押し当てて取付"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "-4.5㎜幅",
"ToolOther": "30cN･m",
"WorkName": "Rﾌﾚｰﾑ組立2",
"WorkItems": [
"4. PIN を本締めし㉙を外す"
],
"WorkPoints": [
"㉙は図示通り上側にスライドさせる",
"ﾃｰﾌﾟ押さえｶﾞｲﾄﾞを引き下げて戻した時に､引っ掛かり無く摺動する事"
],
"Tolks": [
"締付ﾄﾙｸ 30cN･m"
],
"InspectionNo": "",
"Inspec... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｶﾞｲﾄﾞ組立補助治具",
"Size": "",
"ToolOther": "FM-4816",
"WorkName": "Rﾌﾚｰﾑ組立2",
"WorkItems": [
"3. 完成品に㉙をセットしPIN を仮付け",
"4. PIN を本締めし㉙を外す"
],
"WorkPoints": [
"㉙は図示通り下側にスライドさせる",
"㉙は図示通り上側にスライドさせる",
"ﾃｰﾌﾟ押さえｶﾞｲﾄﾞを引き下げて戻した時に､引っ掛かり無く摺動する事"
],
"Tolks": [
"締付... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4816",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Rﾌﾚｰﾑ組立2",
"WorkItems": [
"◆1. GUIDE にSPRING をｾｯﾄする",
"2. 1完成品を にｾｯﾄする",
"3. 完成品に㉙をセットしPIN を仮付け",
"4. PIN を本締めし㉙を外す"
],
"WorkPoints": [
"㉘をSPRING の両端にそれぞれゴマ粒大を塗布",
"ﾊﾞﾈを押えながら取付けのこと",
"㉙は図示通り下側にスライドさせる",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "正常な事",
"Method": "目視",
"RecordMethod": "WDKC-G09-001",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Rﾌﾚｰﾑ組立2",
"WorkItems": [
"◆1. GUIDE にSPRING をｾｯﾄする",
"2. 1完成品を にｾｯﾄする",
"3. 完成品に㉙をセットしPIN を仮付け",
"4. PIN を本締めし㉙を外す"
],
"WorkPoints": [
"㉘をSPRING の両端にそれぞれゴマ粒大を塗布",
"ﾊﾞﾈを押えながら取付けのこと",
"㉙は図示通り下側にスライドさせる",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:4",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "-幅4.5㎜",
"ToolOther": "40cN･m",
"WorkName": "ｱﾀｯﾁﾒﾝﾄ接続部取付",
"WorkItems": [
"1. に をPIN で取付ける",
"2. 配線を㉘で固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｱﾀｯﾁﾒﾝﾄ接続部取付",
"WorkItems": [
"1. に をPIN で取付ける",
"2. 配線を㉘で固定する"
],
"WorkPoints": [
"ﾌﾚｰﾑより下に出ない",
"皿ﾓﾐに乗り上げない",
"A側から見て端子が下図のように右側になるように取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "15cN･m",
"WorkName": "ﾃｰﾌﾟ浮き検出ｾﾝｻ確認",
"WorkItems": [
"■3. 各ｾﾝｻの投光側を遮光したときに､遮光したｾﾝｻの受光側がONしないことを確認する",
"■1. ﾃｰﾌﾟ浮き検出ｾﾝｻの投光･受光の配列を確認する",
"■2. ｾﾝｻの組換えがある場合､締付けﾄﾙｸ確認をする"
],
"WorkPoints": [
"前後､作業を実施すること",
"配列に間違いが無いこと",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾌｨｰﾀﾞｶﾊﾞｰ取付け位置の調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "ﾌｨｰﾀﾞｶﾊﾞｰ取付け位置の調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｶﾊﾞｰ取付け位置の調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"WEPJ-G002-A02"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "102.0~104.0㎜120.5~122.0㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WEPJ-G002-A02",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "ｺﾞﾑｽﾄｯﾊﾟｰ調整①",
"WorkItems": [
"■1. ﾌｨｰﾀﾞｰｶﾊﾞｰ側のｽﾄｯﾊﾟｰ調整を行う"
],
"WorkPoints": [
"前後､作業を実施すること",
"C部分:隙間",
"左側",
"右側",
"調整後､Xﾋﾞｰﾑとﾌｨｰﾀﾞｶﾊﾞｰが干渉しないことを確認する",
"ﾌｨｰﾀﾞｶﾊﾞｰA/B寸法調整後に実施すること",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "Xﾋﾞｰﾑ隙間調整治具(Gｼﾘｰｽﾞ)",
"Size": "",
"ToolOther": "FM-5970",
"WorkName": "ｺﾞﾑｽﾄｯﾊﾟｰ調整①",
"WorkItems": [
"■1. ﾌｨｰﾀﾞｰｶﾊﾞｰ側のｽﾄｯﾊﾟｰ調整を行う"
],
"WorkPoints": [
"前後､作業を実施すること",
"C部分:隙間",
"左側",
"右側",
"調整後､Xﾋﾞｰﾑとﾌｨｰﾀﾞｶﾊﾞｰが干渉しないことを確認する",
"ﾌｨｰﾀﾞｶﾊﾞｰA/B寸法調整後に実施すること... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5970",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A02",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "T20H",
"ToolOther": "194cN･m",
"WorkName": "安全SW位置調整",
"WorkItems": [
"■3. 開閉ｶﾊﾞｰを開けて安全ｽｲｯﾁのﾎﾞﾙﾄを締める"
],
"WorkPoints": [
"ﾌｨｰﾀﾞｶﾊﾞｰ側の安全ｽｲｯﾁのﾎﾞﾙﾄを軽く2箇所緩める"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "開閉ｶﾊﾞｰ安全SW調整治具(Gｼﾘｰｽﾞ)",
"Size": "",
"ToolOther": "FM-6034",
"WorkName": "安全SW位置調整",
"WorkItems": [
"■1. 開閉ｶﾊﾞｰを開けて安全ｽｲｯﾁにｼﾞｸﾞを取付ける",
"■2. ｼﾞｸﾞを付けたまま開閉ｶﾊﾞｰを閉じて安全ｽｲｯﾁを調整する",
"■4. ㉘を取外す",
"■5. ㉖を取外す"
],
"WorkPoints": [
"前後､作業を実施すること",
"取外し忘れのないこと!",
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6034",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A02",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "ｺﾞﾑｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾌｨｰﾀﾞｶﾊﾞｰ､開閉ｶﾊﾞｰの両方を閉じた時の隙間を確認する",
"2. ﾌｨｰﾀﾞｰｶﾊﾞ側のｽﾄｯﾊﾟｰ調整を行う"
],
"WorkPoints": [
"前後､作業を実施すること",
"隙間 0.1mm止まりとなるよう調整する",
"ﾌｨｰﾀﾞｶﾊﾞｰA/B寸法調整後に実施すること",
"下面か... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾞﾑｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾌｨｰﾀﾞｶﾊﾞｰ､開閉ｶﾊﾞｰの両方を閉じた時の隙間を確認する",
"2. ﾌｨｰﾀﾞｰｶﾊﾞ側のｽﾄｯﾊﾟｰ調整を行う"
],
"WorkPoints": [
"前後､作業を実施すること",
"隙間 0.1mm止まりとなるよう調整する",
"ﾌｨｰﾀﾞｶﾊﾞｰA/B寸法調整後に実施すること",
"下面から見上げる形で確認",... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.2㎜通り",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-A02",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾞﾑｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾌｨｰﾀﾞｶﾊﾞｰ､開閉ｶﾊﾞｰの両方を閉じた時の隙間を確認する",
"2. ﾌｨｰﾀﾞｰｶﾊﾞ側のｽﾄｯﾊﾟｰ調整を行う"
],
"WorkPoints": [
"前後､作業を実施すること",
"隙間 0.1mm止まりとなるよう調整する",
"ﾌｨｰﾀﾞｶﾊﾞｰA/B寸法調整後に実施すること",
"下面から見上げる形で確認",... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.3㎜通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-A02",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾃｰﾌﾟ浮きｲﾝﾀｰﾛｯｸ確認",
"WorkItems": [],
"WorkPoints": [
"ﾚﾊﾞｰでﾌｯｸを解除しｶﾊﾞｰを前に動かしていく",
"ﾚﾊﾞｰ",
"ﾛｯｸ状態",
"解除状態",
"ﾌｯｸ",
"ﾌｯｸが外れた状態で保持できる位置でOFFすること",
"ﾌｯｸが外れた状態で保持できる位置でOFFすること",
"緑だけが点灯していること"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ浮きｲﾝﾀｰﾛｯｸ確認",
"WorkItems": [
"2. 検査書の指定ｽﾛｯﾄにﾌｨｰﾀﾞをｾｯﾄし､ﾄｯﾌﾟﾃｰﾌﾟ押さえをｵｰﾌﾟﾝするとB/CいずれかのｾﾝｻがOFFすることを確認する",
"1. 交換台車をｾｯﾄしてｼｭｰﾄの内側を遮光し､AのｾﾝｻがOFFすることを確認する",
"3. ﾌｨｰﾀﾞｶﾊﾞｰが完全に閉まっていない状態でDがOFF､閉まっている状態でONすることを確認する",
"4. 検査異常がある場合､ﾌ... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに動作出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A02",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "安全ｽｲｯﾁ動作確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6052",
"WorkName": "開閉ｶﾊﾞｰ安全SWの動作確認",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"WEPJ-G002-A02"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-6052",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに動作出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A02",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "搬送開口部ｾﾝｻの高さ調整",
"WorkItems": [
"■1. ㉖をコンベアにセットし、搬送開口部センサの確認・調整を行なう"
],
"WorkPoints": [
"延長ｺﾝﾍﾞｱ仕様時は､延長ｺﾝﾍﾞｱ部に開口部ｾﾝｻを移行する為､調整不要",
"左右搬送開口部で作業を実施すること",
"左側",
"右側",
"搬送開口部ｾﾝｻ",
"左側",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "開口部ｾﾝｻｰ位置確認治具",
"Size": "",
"ToolOther": "FM-4490",
"WorkName": "搬送開口部ｾﾝｻの高さ調整",
"WorkItems": [
"■1. ㉖をコンベアにセットし、搬送開口部センサの確認・調整を行なう"
],
"WorkPoints": [
"延長ｺﾝﾍﾞｱ仕様時は､延長ｺﾝﾍﾞｱ部に開口部ｾﾝｻを移行する為､調整不要",
"左右搬送開口部で作業を実施すること",
"左側",
"右側",
"搬送開口部ｾﾝｻ",
"左側",
... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4490",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに動作出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A02",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "【OP】延長ｺﾝﾍﾞｱ搬送開口部ｾﾝｻの調整",
"WorkItems": [
"■2. ㉖を延長コンベアにセットし、搬送開口部センサの調整・確認を行なう",
"1. 延長ｺﾝﾍﾞｱのｹｰﾌﾞﾙCNEXL･CNEXRを､本体に接続する"
],
"WorkPoints": [
"8㎜で光軸 通過(緑･橙点灯)",
"10㎜で光軸 遮断(緑点灯･橙消灯)",
"前側､後側両方で確認するこ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.