input stringclasses 1
value | instruction stringlengths 202 3.29k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結【260㎜対応】",
"WorkItems": [],
"WorkPoints": [
"㉚,㉝でロックする"
],
"Tolks": [
"締付ﾄﾙｸ 30.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"WASHER を取付けｸﾞﾘｰｽをなじませる",
"WASHER の上にも... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "7.50±0.05㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結【260㎜対応】",
"WorkItems": [
"上ﾌﾟﾚｰﾄを上下させﾘﾆｱﾌﾞｯｼｭとｼｬﾌﾄのこじれが無くｽﾑｰｽﾞに動くか確認する事",
"5. ｼﾘﾝﾀﾞｰをｽﾊﾟﾅの入る位置まで上昇させ､ﾛｯﾄﾞ寸法の位置決め後､ﾛｯｸする",
"3. のＡに治具㉗の配管を繋ぐ",
"2. ㉘でプレートとシリンダーの芯出しを実施し、シリンダーを固定する",
"1. CYL-NUT に油砥石をかける",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:8",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "36㎜",
"ToolOther": "30.0N･m",
"WorkName": "上ﾌﾟﾚｰﾄとｼﾘﾝﾀﾞの連結【260㎜対応】",
"WorkItems": [],
"WorkPoints": [
"㉚,㉝でロックする"
],
"Tolks": [
"締付ﾄﾙｸ 30.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"WASHER を取付けｸﾞﾘｰｽをなじませる",
"WA... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｾﾝｻｰ、ﾄﾞｸﾞ取付け調整",
"WorkItems": [
"1. DOG に防錆油を塗布する",
"2. にDOG をBOLT WASHER で取付け",
"3. ｾﾝｻ位置調整後､Aを締付け"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰを上下させﾄﾞｸﾞとｾﾝｻｰが接触しないように調整する",
" ｼﾘﾝﾀﾞｰを上昇させ､上のｾﾝｻｰで位置調整DOG ゆっくり下げて下ｾﾝｻｰの... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｾﾝｻｰ、ﾄﾞｸﾞ取付け調整",
"WorkItems": [
"1. DOG に防錆油を塗布する",
"2. にDOG をBOLT WASHER で取付け",
"3. ｾﾝｻ位置調整後､Aを締付け"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰを上下させﾄﾞｸﾞとｾﾝｻｰが接触しないように調整する",
"ｾﾝｻｰの左右はｾﾝﾀﾞｰ奥行きは2/3を目安に取付け",
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"表裏面",
"上面",
"WEAV-G002-C10"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "出代:50±0.1㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WEAV-G002-C10",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"表裏面",
"上面",
"WEAV-G002-C10"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "高さ:110.5±0.05㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C10",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"表裏面",
"上面"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"表裏面",
"上面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "側面ﾌﾟﾚｰﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-4828",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"表裏面",
"上面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4828",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "側面ﾌﾟﾚｰﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-2675",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"表裏面",
"上面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2675",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整①",
"WorkItems": [
"1. PLATE PLATE に油砥石をかける",
"2. にPLATE PLATE をBOLT で仮取付け",
"3. PLATE PLATE の取付高さ調整及び平面度を測定する"
],
"WorkPoints": [
"表裏面と上面にかける",
"上下ｽﾋﾟｰﾄﾞを仮に上昇(1.20~1.50)下降(1.35~1.65)に調整",
"ﾁｪｯ... | {
"QualityItem": "仕様確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "仕様指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整②",
"WorkItems": [
"2. を動作させ､上がった状態でﾚｰﾙの平行を調整する",
"1. 治具台に㉙を取付ける"
],
"WorkPoints": [
"治具台と㉙に隙間が無いこと",
"最終確認は一度上下動作させ測定の事",
" ④は調整不可( ､④の差が大きい場合は治具を確認する)",
"治具取付位置:ﾌﾟﾚｰﾄ端面から治具端面... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "平面度0.05㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C10",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整②",
"WorkItems": [
"2. を動作させ､上がった状態でﾚｰﾙの平行を調整する",
"1. 治具台に㉙を取付ける"
],
"WorkPoints": [
"治具台と㉙に隙間が無いこと",
"最終確認は一度上下動作させ測定の事",
" ④は調整不可( ､④の差が大きい場合は治具を確認する)",
"治具取付位置:ﾌﾟﾚｰﾄ端面から治具端面まで4±... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ上昇ｽﾄｯﾊﾟｰ",
"Size": "",
"ToolOther": "FM-3167",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整②",
"WorkItems": [
"2. を動作させ､上がった状態でﾚｰﾙの平行を調整する",
"1. 治具台に㉙を取付ける"
],
"WorkPoints": [
"治具台と㉙に隙間が無いこと",
"最終確認は一度上下動作させ測定の事",
" ④は調整不可( ､④の差が大きい場合は治具を確認する)",
"治具取付位置:ﾌﾟﾚｰﾄ端面から治... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3167",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整②",
"WorkItems": [
"2. を動作させ､上がった状態でﾚｰﾙの平行を調整する",
"1. 治具台に㉙を取付ける"
],
"WorkPoints": [
"治具台と㉙に隙間が無いこと",
"最終確認は一度上下動作させ測定の事",
" ④は調整不可( ､④の差が大きい場合は治具を確認する)",
"治具取付位置:ﾌﾟﾚｰﾄ端面から治具端... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整②",
"WorkItems": [
"2. を動作させ､上がった状態でﾚｰﾙの平行を調整する",
"1. 治具台に㉙を取付ける"
],
"WorkPoints": [
"治具台と㉙に隙間が無いこと",
"最終確認は一度上下動作させ測定の事",
" ④は調整不可( ､④の差が大きい場合は治具を確認する)",
"治具取付位置:ﾌﾟﾚｰﾄ端面から治具端面まで4±1㎜で取付け... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "4±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付け調整②",
"WorkItems": [
"2. を動作させ､上がった状態でﾚｰﾙの平行を調整する",
"1. 治具台に㉙を取付ける"
],
"WorkPoints": [
"治具台と㉙に隙間が無いこと",
"最終確認は一度上下動作させ測定の事",
" ④は調整不可( ､④の差が大きい場合は治具を確認する)",
"治具取付位置:ﾌﾟﾚｰﾄ端面から治具端面まで4±1㎜で取付け... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "出代:50±0.1㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整",
"WorkItems": [
"1. の上ﾌﾟﾚｰﾄに を仮取付",
"2. の平面度調整を行う"
],
"WorkPoints": [
" ④⑤⑧番のﾎﾞﾙﾄを治具基準に調整",
" ③⑥⑦の高さ: を基準に-0.04~-0.09mm",
"⑨⑩⑪⑫の高さ: を基準に-0.02~-0.06mm",
"④⑤⑧の平面度: を基準に平面度0.... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "高さ:2.5±0.025㎜高さ:-0.02~-0.06㎜高さ:-0.04~-0.09㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C10",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整",
"WorkItems": [
"1. の上ﾌﾟﾚｰﾄに を仮取付",
"2. の平面度調整を行う"
],
"WorkPoints": [
" ④⑤⑧番のﾎﾞﾙﾄを治具基準に調整",
" ③⑥⑦の高さ: を基準に-0.04~-0.09mm",
"⑨⑩⑪⑫の高さ: を基準に-0.02~-0.06mm",
"④⑤⑧の平面度: を基準に平面度0.... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "高さ:2.5±0.025㎜高さ:-0.02~-0.06㎜高さ:-0.04~-0.09㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C10",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ上昇ｽﾄｯﾊﾟｰ",
"Size": "",
"ToolOther": "FM-3167",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整",
"WorkItems": [
"1. の上ﾌﾟﾚｰﾄに を仮取付",
"2. の平面度調整を行う"
],
"WorkPoints": [
" ④⑤⑧番のﾎﾞﾙﾄを治具基準に調整",
" ③⑥⑦の高さ: を基準に-0.04~-0.09mm",
"⑨⑩⑪⑫の高さ: を基準に-0.02~-0.06mm",
"④⑤⑧の平面度: を基準に平面... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3167",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整",
"WorkItems": [
"1. の上ﾌﾟﾚｰﾄに を仮取付",
"2. の平面度調整を行う"
],
"WorkPoints": [
" ④⑤⑧番のﾎﾞﾙﾄを治具基準に調整",
" ③⑥⑦の高さ: を基準に-0.04~-0.09mm",
"⑨⑩⑪⑫の高さ: を基準に-0.02~-0.06mm",
"④⑤⑧の平面度: を基準に平面度0... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾌﾟﾚｰﾄ搭載面調整冶具",
"Size": "",
"ToolOther": "FM-4639",
"WorkName": "下受けﾌﾟﾚｰﾄ搭載面取付け調整",
"WorkItems": [
"1. の上ﾌﾟﾚｰﾄに を仮取付",
"2. の平面度調整を行う"
],
"WorkPoints": [
" ④⑤⑧番のﾎﾞﾙﾄを治具基準に調整",
" ③⑥⑦の高さ: を基準に-0.04~-0.09mm",
"⑨⑩⑪⑫の高さ: を基準に-0.02~-0.06mm",
"④⑤⑧の平面度: を基準に平... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4639",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付け",
"WorkItems": [
"1. にGUIDE をBOLT で､ をBOLT WASHER で取付け"
],
"WorkPoints": [
" ､ をﾋﾟﾝに押し当てて取付け",
"隙間:0.05㎜が入らないこと"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 3.5N･m",
"BOLT 締付ﾄﾙｸ 9.8N･m"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付け",
"WorkItems": [
"1. にGUIDE をBOLT で､ をBOLT WASHER で取付け"
],
"WorkPoints": [
" ､ をﾋﾟﾝに押し当てて取付け",
"隙間:0.05㎜が入らないこと"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 3.5N･m",
"BOLT 締付ﾄﾙｸ 9.8N･m"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "0.05㎜",
"WorkName": "ｶﾞｲﾄﾞ・ﾌﾞﾛｯｸ・ｸﾗﾝﾌﾟ取付け",
"WorkItems": [
"1. にGUIDE をBOLT で､ をBOLT WASHER で取付け"
],
"WorkPoints": [
" ､ をﾋﾟﾝに押し当てて取付け",
"隙間:0.05㎜が入らないこと"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 3.5N･m",
"BOLT 締付ﾄﾙｸ 9.8N･m"
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間0.05㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｴｰｼﾞﾝｸﾞ準備",
"WorkItems": [
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際には標準ﾌﾟﾚｰﾄを取付けて実施する",
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際には標準ﾌﾟﾚｰﾄを取付けて実施する"
],
"Tolks": [],
... | {
"QualityItem": "遮光確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "LEDが消灯する事",
"Method": "目視",
"RecordMethod": "WEAV-G002-C10",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｴｰｼﾞﾝｸﾞ準備",
"WorkItems": [
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際には標準ﾌﾟﾚｰﾄを取付けて実施する",
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際には標準ﾌﾟﾚｰﾄを取付けて実施する"
],
"Tolks": [],
... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上昇:1.30~1.40S下降:1.20~1.30S上昇時:0.40~0.46S下降時:1.21~1.22S",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｴｰｼﾞﾝｸﾞ準備",
"WorkItems": [
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う"
],
"WorkPoints": [
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際には標準ﾌﾟﾚｰﾄを取付けて実施する",
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う際には標準ﾌﾟﾚｰﾄを取付けて実施する"
],
"Tolks": [],
... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上昇:1.30~1.40S下降:1.20~1.30S上昇時:0.40~0.46S下降時:1.21~1.22S",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｰｼﾞﾝｸﾞ用ｳｪｲﾄ治具",
"Size": "",
"ToolOther": "FM-5332",
"WorkName": "ｴｰｼﾞﾝｸﾞ準備",
"WorkItems": [
"2. ﾊﾞﾙﾌﾞ､ｽﾋﾟｺﾝの調整を行う",
"3. 通常ｽﾋﾟｰﾄﾞで上記A,Cﾂﾏﾐで調整｡",
"4. 速度切替ﾓｰﾄﾞでの確認｡",
"1. のｾﾝｻｰ部の遮光を確認する"
],
"WorkPoints": [
"ｴｰｼﾞﾝｸﾞ後､再度確認する為､検査表記入は不要",
"ｽﾋﾟｰﾄﾞ調整､ｴｰｼﾞﾝｸﾞを行う... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5332",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"1. ｴｰｼﾞﾝｸﾞを実施する｡"
],
"WorkPoints": [
"注意｢③の切替時｣｢A･Bの上下動作時｣隣に同じく作業する作業者がい無い事(勘違いにより反対側を動作させてしまう恐れが有る)",
"ﾕﾆｯﾄﾁｪｯｶｰ使用前にｴｱｰ圧力確認を行う事:500~505kPa",
"動作しなくなった場合はｽﾄｯﾌﾟ及び電源OFF安全の為二人作業... | {
"QualityItem": "動作回数確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "2000回",
"Method": "目視",
"RecordMethod": "WEAV-G002-C10",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｰｼﾞﾝｸﾞ用ｳｪｲﾄ治具",
"Size": "",
"ToolOther": "FM-5332",
"WorkName": "ｴｰｼﾞﾝｸﾞ",
"WorkItems": [
"1. ｴｰｼﾞﾝｸﾞを実施する｡"
],
"WorkPoints": [
"注意｢③の切替時｣｢A･Bの上下動作時｣隣に同じく作業する作業者がい無い事(勘違いにより反対側を動作させてしまう恐れが有る)",
"ﾕﾆｯﾄﾁｪｯｶｰ使用前にｴｱｰ圧力確認を行う事:500~505kPa",
"動作しなくなった場合はｽﾄｯﾌﾟ及び電源OFF安全の為二人... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5332",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｽﾋﾟｰﾄﾞ調整",
"WorkItems": [
"1.ｴｰｼﾞﾝｸﾞ実施後､基板ﾎﾙﾀﾞｰの動作確認を行う",
"3. ｴｰｼﾞﾝｸﾞ完了後､再度ｽﾋﾟｰﾄﾞ調整を行う",
"2. ｼﾘﾝﾀﾞｰとｼｬﾌﾄのこじれを取る"
],
"WorkPoints": [
" 、上プレートが下限の状態で、シリンダー締め付けボルトを一度緩める②、㉖のスイッチで上プレートを3回上下させてこじれがない状態を確認し... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上昇:1.30~1.40S下降:1.20~1.30S上昇時:0.40~0.55S下降時:1.21~1.22S",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "WEAV-G002-C10",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2999",
"WorkName": "ｽﾋﾟｰﾄﾞ調整",
"WorkItems": [
"1.ｴｰｼﾞﾝｸﾞ実施後､基板ﾎﾙﾀﾞｰの動作確認を行う",
"3. ｴｰｼﾞﾝｸﾞ完了後､再度ｽﾋﾟｰﾄﾞ調整を行う",
"2. ｼﾘﾝﾀﾞｰとｼｬﾌﾄのこじれを取る"
],
"WorkPoints": [
" 、上プレートが下限の状態で、シリンダー締め付けボルトを一度緩める②、㉖のスイッチで上プレートを3回上下させてこじれがない状態を確認し... | {
"QualityItem": "速度確認",
"ToolManageNo": "FM-2999",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上昇:1.30~1.40S下降:1.20~1.30S上昇時:0.40~0.55S下降時:1.21~1.22S",
"Method": "基板ﾎﾙﾀﾞｰﾁｪｯｶｰ",
"RecordMethod": "WEAV-G002-C10",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｽﾋﾟｰﾄﾞ調整",
"WorkItems": [],
"WorkPoints": [
"2箇所のﾎﾞﾙﾄを緩めて調整する"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｰｼﾞﾝｸﾞ用ｳｪｲﾄ治具",
"Size": "",
"ToolOther": "FM-5332",
"WorkName": "ｽﾋﾟｰﾄﾞ調整",
"WorkItems": [
"1.ｴｰｼﾞﾝｸﾞ実施後､基板ﾎﾙﾀﾞｰの動作確認を行う",
"3. ｴｰｼﾞﾝｸﾞ完了後､再度ｽﾋﾟｰﾄﾞ調整を行う",
"2. ｼﾘﾝﾀﾞｰとｼｬﾌﾄのこじれを取る"
],
"WorkPoints": [
" 、上プレートが下限の状態で、シリンダー締め付けボルトを一度緩める②、㉖のスイッチで上プレートを3回上下させてこじれがない状態を確... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5332",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘番・警告ﾗﾍﾞﾙ貼付け",
"WorkItems": [
"1. にLABEL ,LABEL ,LABEL を貼付け"
],
"WorkPoints": [
"指示寸法 各±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"製造手配銘板(ｾﾝｻｰのﾄﾞｸﾞ部)",
"3㎜",
... | {
"QualityItem": "貼付け確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "銘板貼付冶具",
"Size": "",
"ToolOther": "FM-4920",
"WorkName": "銘番・警告ﾗﾍﾞﾙ貼付け",
"WorkItems": [
"1. にLABEL ,LABEL ,LABEL を貼付け"
],
"WorkPoints": [
"指示寸法 各±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"製造手配銘板(ｾﾝｻｰのﾄﾞｸﾞ部)",
"3㎜",
... | {
"QualityItem": "貼付け確認",
"ToolManageNo": "FM-4920",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘番・警告ﾗﾍﾞﾙ貼付け②",
"WorkItems": [
"1. の各ﾚｰﾝに対応したｼｰﾙを貼付ける事"
],
"WorkPoints": [
"貼付け寸法は前ﾍﾟｰｼﾞ参照の事",
"貼付け向きに注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "貼付け確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ移載治具",
"Size": "",
"ToolOther": "FM-4489",
"WorkName": "払い出し準備",
"WorkItems": [
"1. に㉖を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4489",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-LEFT)組立①",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"下記ｷｯﾄは､扉前左が共通の為､同様に作成の事",
"扉上側",
"A矢視図",
"中央ﾌﾚｰﾑ固定用の穴が扉下側になるよう組付け"
],
"Tolks": [],
"Insp... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-LEFT)組立②",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT ･NUT ･CAP を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"下記ｷｯﾄは､扉前左が共通の為､同様に作成の事",
"扉左側",
"裏面図",
"ﾀｯﾌﾟ穴が扉左側になるよう組付け"
],
"Tolks": [],
"I... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-LEFT)組立③",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"下記ｷｯﾄは､扉前左が共通の為､同様に作成の事",
"ﾌﾗｯﾄ面",
"扉上側",
"中央ﾌﾚｰﾑ固定用の穴が扉下側になるよう組付け"
],
"Tolks": [],
"Ins... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-LEFT)組立④",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT ･NUT ･CAP を取付",
"2. 1.完成品にCAP を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"下記ｷｯﾄは､扉前左が共通の為､同様に作成の事",
"ﾌﾗｯﾄ面",
"扉左側",
"A面",
"B面"
]... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-LEFT)組立⑤",
"WorkItems": [],
"WorkPoints": [
"ｶｯﾄした両端を､更に図のようにｶｯﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1.完成品",
"L=430",
"L=697.5",
"外側面",
"... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-LEFT)組立⑥",
"WorkItems": [
"1. にHINGE をSCREW で取付"
],
"WorkPoints": [
"取っ手取付用穴",
"白ﾌﾟﾗｽﾁｯｸが下になる様に取付",
"下記ｷｯﾄは､扉前左が共通の為､同様に作成の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-LEFT)組立⑦",
"WorkItems": [
"2. BRACKET にSWITCH をNUT-PLATE ･BOLT ･WASHER ･WASHER で取付",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [
"下記ｷｯﾄは､扉前左が共通の為､同様に作成の事"
],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-033",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-LEFT)組立⑦",
"WorkItems": [
"2. BRACKET にSWITCH をNUT-PLATE ･BOLT ･WASHER ･WASHER で取付",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [
"下記ｷｯﾄは､扉前左が共通の為､同様に作成の事"
],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-033",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾍｷｻﾛT20",
"ToolOther": "1.0N･m",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-LEFT)組立⑦",
"WorkItems": [
"2. BRACKET にSWITCH をNUT-PLATE ･BOLT ･WASHER ･WASHER で取付",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [
"下記ｷｯﾄは､扉前左が共通の為､同様に作成の事"
],
"Tolks": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-LEFT)組立⑧",
"WorkItems": [
"1. に をBOLT ･WASHER で取付"
],
"WorkPoints": [
"取っ手取付用穴",
"下記ｷｯﾄは､扉前左が共通の為､同様に作成の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"×2",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-LEFT)組立⑨",
"WorkItems": [
"1. にCATCH をBOLT で取付"
],
"WorkPoints": [
"取っ手取付用穴",
"下記ｷｯﾄは､扉前左が共通の為､同様に作成の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"×2",
"内... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-LEFT)組立⑩",
"WorkItems": [
"1. にBRACKET ･PLATE をBOLT ･WASHER ･BOLT で取付"
],
"WorkPoints": [
"ﾌﾚｰﾑ下面に直角平行に取付",
"取っ手取付用穴",
"ﾌﾚｰﾑに対して直角平行に取付",
"A矢視図",
"下記ｷｯﾄは､扉前左が共通の為､同様に作成の事"
],
"Tolks": []... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-LEFT)組立⑪",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立①",
"WorkItems": [
"1. FRAME にSUPPORT NUT NUT を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"扉上側",
"A矢視図",
"中央ﾌﾚｰﾑ固定用の穴が扉下側になるよう組付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立②",
"WorkItems": [
"1. FRAME にSUPPORT NUT CAP を取付"
],
"WorkPoints": [
"扉左側",
"風船色ﾅｯﾄｻｲｽﾞ",
"裏面図",
"ﾀｯﾌﾟ穴が扉左側になるよう組付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立③",
"WorkItems": [
"1. FRAME にSUPPORT NUT を取付"
],
"WorkPoints": [
"ﾌﾗｯﾄ面",
"扉上側",
"風船色ﾅｯﾄｻｲｽﾞ",
"中央ﾌﾚｰﾑ固定用の穴が扉下側になるよう組付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立④",
"WorkItems": [
"1. FRAME にCAP を取付"
],
"WorkPoints": [
"扉左側",
"風船色ﾅｯﾄｻｲｽﾞ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"M6",
"M5",
"M4",
"M3"
]
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑤",
"WorkItems": [
"1. CLAMP を指定の長さにｶｯﾄ",
"2. 1.完成品･ FRAME PANEL PANEL をBOLT で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"外側面",
"L=81... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑥",
"WorkItems": [
"1. にHINGE をSCREW で取付"
],
"WorkPoints": [
"取っ手取付用穴",
"白ﾌﾟﾗｽﾁｯｸが下になる様に取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"外側面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑦",
"WorkItems": [
"2. BRACKET にSWITCH をNUT-PLATE BOLT WASHER WASHER で取付",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems"... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-036",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑦",
"WorkItems": [
"2. BRACKET にSWITCH をNUT-PLATE BOLT WASHER WASHER で取付",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems"... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-036",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾍｷｻﾛT20",
"ToolOther": "1.0N･m",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑦",
"WorkItems": [
"2. BRACKET にSWITCH をNUT-PLATE BOLT WASHER WASHER で取付",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": ""... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑧",
"WorkItems": [
"1. に をBOLT ･WASHER で取付"
],
"WorkPoints": [
"取っ手取付用穴"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"×2",
"内側面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑨",
"WorkItems": [
"1. にCATCH をBOLT で取付",
"2. にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"取っ手取付用穴"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"×2",
"内側面",... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑩",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付け①",
"WorkItems": [
"1. 貼付け面を清掃する",
"2. LABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"後 面",
"前 面",
"10mm"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付け②",
"WorkItems": [
"1. 貼付け面を清掃する",
"2. LABEL LABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"後 面",
"前 面",
"5mm",
"5mm"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付け③",
"WorkItems": [
"1. 貼付け面を清掃する",
"2. LABEL LABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"後 面",
"前 面",
"5mm",
"5mm"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付け④",
"WorkItems": [
"1. 貼付け面を清掃する",
"2. LABEL LABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"後 面",
"前 面",
"5mm",
"5mm"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付け⑤",
"WorkItems": [
"1. 貼付け面を清掃する",
"2. LABEL LABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"後 面",
"前 面",
"5mm",
"5mm"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付け⑥",
"WorkItems": [
"1. 貼付け面を清掃する",
"2. LABEL LABEL LABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"後 面",
"前 面",
"375mm",
"50mm",
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "銘板貼付け⑦(前面右)",
"WorkItems": [
"1. の架台へLABEL LABEL LABEL LABEL LABEL LABEL を貼付ける"
],
"WorkPoints": [
"油脂･ｺﾞﾐを取り寸法を確認して貼付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "銘板貼付け⑧(前面左)",
"WorkItems": [
"1. の架台へLABEL LABEL LABEL LABEL LABEL LABEL LABEL LABEL を貼付ける"
],
"WorkPoints": [
"油脂･ｺﾞﾐを取り寸法を確認して貼付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "銘板貼付け⑨(前面左)",
"WorkItems": [
"1. の架台へLABEL を貼付ける"
],
"WorkPoints": [
"油脂･ｺﾞﾐを取り寸法を確認して貼付け",
"油脂･ｺﾞﾐを取り寸法を確認して貼付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"30㎜",
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "銘板貼付け⑩(後面右)",
"WorkItems": [
"1. の架台へLABEL を貼付ける"
],
"WorkPoints": [
"油脂･ｺﾞﾐを取り寸法を確認して貼付け",
"油脂･ｺﾞﾐを取り寸法を確認して貼付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "銘板貼付け⑪(後面左)",
"WorkItems": [
"1. の架台へLABEL を貼付ける"
],
"WorkPoints": [
"油脂･ｺﾞﾐを取り寸法を確認して貼付け",
"油脂･ｺﾞﾐを取り寸法を確認して貼付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "扉ｽﾄｯﾊﾟｰ部組立",
"WorkItems": [
"1. PLATE にRUBBER-LEG をBOLT で取付",
"2. ㉗にBOLT ・WASHER を入れマスキングテープで止め同梱",
"2. PLATE にRUBBER-LEG をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "扉ﾛｯｸｼﾘﾝﾀﾞｰ部組立①",
"WorkItems": [
"1. CYLINDER にSWITCH を取付",
"2. 1.完成品にLABEL TERMINAL PROCESS ･LABEL TERMINAL PROCESS を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "扉ﾛｯｸｼﾘﾝﾀﾞｰ部組立②",
"WorkItems": [
"1. にJOINT を取付",
"3. 2.完成品にBRACKET をBOLT WASHER で取付",
"2. 1.完成品にJOINT を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1.完成品",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "扉ﾛｯｸｼﾘﾝﾀﾞｰ部組立③",
"WorkItems": [
"1. にPLATE ･CATCH をSPACER NUT BOLT WASHER 取付",
"2. ㉘にBOLT ・WASHER を入れマスキングテープで止め同梱"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業で... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "扉中開閉ｶﾊﾞｰSW組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"WWYJ-5300-032"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-032",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "扉中開閉ｶﾊﾞｰSW組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"WWYJ-5300-032"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-032",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "扉中開閉ｶﾊﾞｰSW組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"WWYJ-5300-032"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-032",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "扉小ﾏｸﾞﾈｯﾄSW部組立",
"WorkItems": [
"■1. BRACKET の型式を確認し､ｼﾘｱﾙNoを検査書に記入",
"4. ㉘にBOLT ・WASHER (各2本)を入れマスキングテープで止め同梱",
"2. BRACKET にSWITCH をBOLT ･WASHER ･WASHER ･NUT-PLATE で取付",
"3. 1.完成品にLABEL TERMINAL PROCESS を取付"
],
"WorkPo... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-031",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "扉小ﾏｸﾞﾈｯﾄSW部組立",
"WorkItems": [
"■1. BRACKET の型式を確認し､ｼﾘｱﾙNoを検査書に記入",
"4. ㉘にBOLT ・WASHER (各2本)を入れマスキングテープで止め同梱",
"2. BRACKET にSWITCH をBOLT ･WASHER ･WASHER ･NUT-PLATE で取付",
"3. 1.完成品にLABEL TERMINAL PROCESS を取付"
],
"WorkPo... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-031",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾍｸｻﾛﾋﾞｭﾗT-20",
"ToolOther": "1.0N･m",
"WorkName": "扉小ﾏｸﾞﾈｯﾄSW部組立",
"WorkItems": [],
"WorkPoints": [
"被覆端面とLABEL TERMINAL PROCESS の端面を合わせて取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1.完成品",
"S357",
"P... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "IC交換ｽｲｯﾁ組立",
"WorkItems": [
"1. BRACKET にCABLE を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"S01004",
"S01005",
"CN5K3010",
"CN15K010"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘｽﾄﾗｯﾌﾟ部組立",
"WorkItems": [
"1. にTERMINAL をBOLT ・WASHER ・㉒で取付",
"2. ㉗にWASHER ・BOLT を入れマスキングテープで止め同梱"
],
"WorkPoints": [
"S01005が取付してあるﾌﾞﾗｹｯﾄに取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"4㎜",
"1.完成品"
]
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:4.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "認識光学系組立①",
"WorkItems": [
"■1. CAMERA の型式確認とｼﾘｱﾙNo.の記入",
"3. LENS のｾｯﾄﾋﾞｽ 3ヶ所を均等に緩め分解",
"▲2. LENS に㉖接着剤を塗布し、CAMERA に組付"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙ番号",
"L･R共通の為､2ｾｯﾄ(1台分)組立 (L･R区分必要)",
"型式確認･ｼﾘｱﾙNo記録"... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-053",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "認識光学系組立①",
"WorkItems": [
"■1. CAMERA の型式確認とｼﾘｱﾙNo.の記入",
"3. LENS のｾｯﾄﾋﾞｽ 3ヶ所を均等に緩め分解",
"▲2. LENS に㉖接着剤を塗布し、CAMERA に組付"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙ番号",
"L･R共通の為､2ｾｯﾄ(1台分)組立 (L･R区分必要)",
"型式確認･ｼﾘｱﾙNo記録"... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-053",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "認識光学系組立①",
"WorkItems": [
"■1. CAMERA の型式確認とｼﾘｱﾙNo.の記入",
"3. LENS のｾｯﾄﾋﾞｽ 3ヶ所を均等に緩め分解",
"▲2. LENS に㉖接着剤を塗布し、CAMERA に組付"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙ番号",
"L･R共通の為､2ｾｯﾄ(1台分)組立 (L･R区分必要)",
"型式確認･ｼﾘ... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布φ3±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "6.3㎜",
"ToolOther": "",
"WorkName": "認識光学系組立②",
"WorkItems": [],
"WorkPoints": [
"LED差込口方向注意",
"CCD方向注意",
"本締め"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1.完成品",
"ﾚﾝｽﾞ側",
"ｾｯﾄﾋﾞｽ 3ヶ所",
"... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:6.3㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "認識光学系組立②",
"WorkItems": [],
"WorkPoints": [
"LED差込口方向注意",
"CCD方向注意",
"本締め"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1.完成品",
"ﾚﾝｽﾞ側",
"ｾｯﾄﾋﾞｽ 3ヶ所",
"㉘ブロックゲ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "寸法:76.07㎜±0.02㎜以内",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "認識光学系組立③",
"WorkItems": [
"■1. LED-LIGHTING-UNIT の型式確認とｼﾘｱﾙNo.の記入",
"2. LED-LIGHTING-UNIT にLABEL TERMINAL PROCESS ･LABEL TERMINAL PROCESS を取付",
"3. に1.完成品を取付"
],
"WorkPoints": [
"合わせる",
"型式確認･ｼﾘｱﾙNo.記録",
"L･... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-053",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "認識光学系組立③",
"WorkItems": [
"■1. LED-LIGHTING-UNIT の型式確認とｼﾘｱﾙNo.の記入",
"2. LED-LIGHTING-UNIT にLABEL TERMINAL PROCESS ･LABEL TERMINAL PROCESS を取付",
"3. に1.完成品を取付"
],
"WorkPoints": [
"合わせる",
"型式確認･ｼﾘｱﾙNo.記録",
"L･... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-053",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【ACF貼付けﾕﾆｯﾄL/R】への組付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台上面中継JOINT組付け①",
"WorkItems": [
"1. 又は をBOLT WASHER 又はBOLT WASHER で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"後 面",
"前 面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台上面中継JOINT組付け②",
"WorkItems": [
"1. 又は をBOLT WASHER 又はBOLT WASHER で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"後 面",
"前 面",
"1軸仕様の場合",
"2軸仕様の場合"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｲｵﾅｲｻﾞｰ・ｶﾊﾞｰﾛｯｸ用ﾊﾞﾙﾌﾞ組付け",
"WorkItems": [
"1. 又は をBOLT WASHER 又はBOLT WASHER で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"後 面",
"前 面",
"1軸仕様の場合",
"2軸... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.