input stringclasses 1
value | instruction stringlengths 202 3.29k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "正流れ本体組立⑥(搬送部ﾄﾞｯｷﾝｸﾞ)",
"WorkItems": [
"1. にSCREW を取付",
"2. 1.完成品に⑥をSPACER WASHER ㉒で取付"
],
"WorkPoints": [
"上面",
"矢視"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "正流れ本体組立⑦(搬送部ﾄﾞｯｷﾝｸﾞ)",
"WorkItems": [
"1. に をBOLT で取付",
"2. 1.完成品のｹｰﾌﾞﾙﾍﾞｱをBOLT WASHER WASHER で取付"
],
"WorkPoints": [
"上面",
"矢視"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "正流れ本体組立⑧(SP2X軸ﾌｪﾗｲﾄｺｱ取付)",
"WorkItems": [
"3. 1.完成品をブラケット上のFT4にフェライトコアを俵積みして㉗で固定",
"2. 付属のフェライトコアを所定の配線（モーター線、エンコーダー線、信号線）に㉖で固定",
"1. SP2X軸の配線3本配管3本をFT4に㉗で固定"
],
"WorkPoints": [
"矢視",
"ﾌｪﾗｲﾄｺｱ",
"フェライトコアを配線に㉖... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-185",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "正流れ本体組立⑨(SDX軸ﾌｪﾗｲﾄｺｱ取付)",
"WorkItems": [
"3. 1.完成品をブラケット上のFT4にフェライトコアを俵積みして㉗で固定",
"1. SDX軸の配線3本配管3本をFT4に㉗で固定",
"2. 付属のフェライトコアを所定の配線（モーター線、エンコーダー線、信号線）に㉖で固定"
],
"WorkPoints": [
"矢視",
"配線1本にﾌｪﾗｲﾄｺｱを1個固定",
"ﾌｪﾗｲ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-185",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "正流れ本体組立⑩(上面)",
"WorkItems": [
"1. に をBOLT WASHER で取付(5個)",
"2. 1､完成品に をBOLT WASHER で取付(2個)"
],
"WorkPoints": [
"上面",
"ｽﾍﾟｰｻｰ有り",
"ｽﾍﾟｰｻｰ無し"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "正流れ本体組立⑪",
"WorkItems": [
"1. に をWASHER BOLT で取付"
],
"WorkPoints": [
"正面",
"各面の段差が無いように調整し締結する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "正流れ本体組立⑫(前面ｶﾞｽｹｯﾄ取付)",
"WorkItems": [
"1. にGASKET GASKET GASKET GASKET を貼付"
],
"WorkPoints": [
"正面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"幅8㎜L=490㎜",
"幅8㎜L=376㎜",... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "正流れ本体組立⑬(後面ｶﾞｽｹｯﾄ取付)",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付(2個)",
"2. 1､完成品にGASKET GASKET GASKET GASKET GASKET GASKET GASKET を貼付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "正流れ本体組立⑭(左側面ｶﾞｽｹｯﾄ取付)",
"WorkItems": [
"1. GASKET を指定の長さにｶｯﾄする",
"2. にｶｯﾄしたGASKET を貼付する"
],
"WorkPoints": [
"左側面",
"GASKET \t1000mm\t4本\t 841mm\t2本\t 440mm\t2本"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "空圧部組立①",
"WorkItems": [
"1. BRACKET にSHEET を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "空圧部組立②",
"WorkItems": [],
"WorkPoints": [
"φ4白ﾁｭｰﾌﾞ:150㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:150.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "空圧部組立③",
"WorkItems": [
"1. を指定寸法にｶｯﾄする"
],
"WorkPoints": [
"φ6 黒",
"110㎜ 1本140㎜ 1本180㎜ 1本",
"φ4 白",
"80㎜ 1本"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "空圧部組立③",
"WorkItems": [
"1. を指定寸法にｶｯﾄする",
"2. VALVE にJOINT AIR-FILTER を取付け､1.完成品を取付ける",
"3. VALVE にJOINT SPEED-CONTROLLER SILENCER を取付け､1.完成品を取付ける"
],
"WorkPoints": [
"φ6 黒",
"110㎜ 1本140㎜ 1本180㎜ 1本",
"φ4 白"... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "全閉から1/3回転開く事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-081",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "空圧部組立④",
"WorkItems": [
"1. BRACKET に を貼付ける",
"4. に3.完成品をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部組立①",
"WorkItems": [
"1. PLATE にPIN を圧入する",
"2. 1.完成品にDOG をBOLT WASHER で取付ける"
],
"WorkPoints": [
"表面",
"裏面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部組立②",
"WorkItems": [
"1. PLATE にPIN を圧入する",
"2. BRACKET にPIN を圧入する"
],
"WorkPoints": [
"出代:5㎜",
"出代:7㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部組立②",
"WorkItems": [
"1. PLATE にPIN を圧入する",
"2. BRACKET にPIN を圧入する"
],
"WorkPoints": [
"出代:5㎜",
"出代:7㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:7.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部組立③",
"WorkItems": [
"1.LINEAR-WAY の型式を確認し､ｼﾘｱﾙNO.を記入する",
"2. LINEAR-WAY にDOG をBOLT WASHER で取付ける",
"3. に2.完成品をBOLT で取付ける"
],
"WorkPoints": [
"型式:SKR3320A-0395-R2E-10WP-08M(83835801K000)",
"平行度0.05㎜以下",
... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-081",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部組立③",
"WorkItems": [
"1.LINEAR-WAY の型式を確認し､ｼﾘｱﾙNO.を記入する",
"2. LINEAR-WAY にDOG をBOLT WASHER で取付ける",
"3. に2.完成品をBOLT で取付ける"
],
"WorkPoints": [
"型式:SKR3320A-0395-R2E-10WP-08M(83835801K000)",
"平行度0.05㎜以下",
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-081",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部組立③",
"WorkItems": [
"1.LINEAR-WAY の型式を確認し､ｼﾘｱﾙNO.を記入する",
"2. LINEAR-WAY にDOG をBOLT WASHER で取付ける",
"3. に2.完成品をBOLT で取付ける"
],
"WorkPoints": [
"型式:SKR3320A-0395-R2E-10WP-08M(83835801K000)",
... | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.05㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-081",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部組立③",
"WorkItems": [
"1.LINEAR-WAY の型式を確認し､ｼﾘｱﾙNO.を記入する",
"2. LINEAR-WAY にDOG をBOLT WASHER で取付ける",
"3. に2.完成品をBOLT で取付ける"
],
"WorkPoints": [
"型式:SKR3320A-0395-R2E-10WP-08M(83835801K000)",
"ﾋ... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.01㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-081",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部組立④",
"WorkItems": [
"1. にSENSOR をBOLT WASHER WASHER で取付け､SENSOR をBOLT WASHER WASHER で取付ける",
"2. 1.完成品に をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.01㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｽﾀﾝﾄﾞ部組込①",
"WorkItems": [
"1. STAND にPIN を圧入する",
"3. 2.完成品に をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾀﾝﾄﾞ部組込②",
"WorkItems": [
"1. にBOLT WASHER NUT を取付ける",
"2. 1.完成品にBLOCK をBOLT で取付ける",
"3. 2.完成品にBLOCK をBOLT で取付け､ADJUST-BOLT を取付ける"
],
"WorkPoints": [
"左右取付",
"調整ﾎﾞﾙﾄは効かさず当付け程度にし､ﾅｯﾄは本止めする"
],
"Tolks": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "空圧部組込",
"WorkItems": [
"1. BRACKET にCABLE をBOLT WASHER WASHER で取付ける",
"2. に1.完成品とBRACKET をBOLT WASHER で取付ける",
"3. 2.完成品にCABLE-SUPPORT を取付ける",
"5. 4.完成品に をBOLT ㉒で取付ける",
"4. 3.完成品にCABLE-SUPPORT をBOLT で取付ける"
],
"Wor... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部組立⑤",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNO.を記入する",
"2. 1.完成品にLABEL TERMINAL PROCESS を取付ける",
"3. に をBOLT で取付ける",
"4. 3完成品に2.完成品をBOLT WASHER で取付ける",
"5. 4.完成品に を取付ける"
],
"WorkPoints": [
"型式:MSMD012... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-081",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部組立⑤",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNO.を記入する",
"2. 1.完成品にLABEL TERMINAL PROCESS を取付ける",
"3. に をBOLT で取付ける",
"4. 3完成品に2.完成品をBOLT WASHER で取付ける",
"5. 4.完成品に を取付ける"
],
"WorkPoints": [
"型式:MSMD012... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-081",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾓｰﾀ原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "ｱｸﾁｭｴｰﾀ部調整",
"WorkItems": [
"3. ブラケットの原点位置合わせ穴に㉗を挿入し プレートを押し当てる",
"2. ﾓｰﾀ軸を回してZ相原点『00』位置にする",
"1. ﾓｰﾀに原点出し治具を接続する"
],
"WorkPoints": [
"ﾋﾟﾝ当てにて固定",
"ｼｬﾌﾄ",
"ﾌﾟﾚｰﾄ",
"ﾌﾞﾗｹｯﾄ"
],
"Tol... | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-081",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "位置合せ治具",
"Size": "",
"ToolOther": "FM-4606",
"WorkName": "ｱｸﾁｭｴｰﾀ部調整",
"WorkItems": [],
"WorkPoints": [
"ﾍﾞﾙﾄ張力 276~321Hz"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"上下"
]
} | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-4606",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部調整",
"WorkItems": [],
"WorkPoints": [
"ﾍﾞﾙﾄ張力 276~321Hz"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"上下",
"WWYJ-5300-081"
]
} | {
"QualityItem": "ﾍﾞﾙﾄﾃﾝｼｮﾝ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "276~321Hz",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "WWYJ-5300-081",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "反転ﾍｯﾄﾞ上下駆動部組込",
"WorkItems": [
"1. に をBOLT で取付ける",
"2. 1.完成品にCABLE を接続し引き回す"
],
"WorkPoints": [
"矢視A",
"矢視B",
" 反転ﾍｯﾄﾞ上下駆動部は､逆流れ用を取付ける(ﾓｰﾀｰ取付け方向が､正流れとは180度反転)"
],
"Tolks": [],
"InspectionNo": "",
"Ins... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-112",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部配線①",
"WorkItems": [
"1. にCABLE CABLE CABLE CABLE を接続し引き回す"
],
"WorkPoints": [
"D1500"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :接続確認",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-112",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部配線②",
"WorkItems": [
"1. にCABLE CABLE CABLE CABLE を接続し引き回す"
],
"WorkPoints": [
"他の箇所の結束は､ｸﾘｰﾝｹｰﾌﾞﾙと合わせて行う"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"IHMM4108R",
"検査表... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-112",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾘｰﾝｹｰﾌﾞﾙ組込",
"WorkItems": [
"1. BRACKET にSHEET を貼付ける",
"3. 2.完成品にCABLE をBOLT で取付ける"
],
"WorkPoints": [
"端面合わせ",
"ｸﾘｰﾝｹｰﾌﾞﾙ取り扱い注意 ｸﾘｰﾝｹｰﾌﾞﾙはﾕﾆｯﾄ組立が完了するまでｴｱﾏｯﾄ等で保護すること ※汚れが付くと浸み込む為取ることが出来ません"
],
"Tolks": []... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾘｰﾝｹｰﾌﾞﾙ空圧側配線",
"WorkItems": [
"1. 空圧部の配線配管を引き回接続する"
],
"WorkPoints": [
"ﾊﾞﾙﾌﾞ配線がﾌﾞﾗｹｯﾄから10㎜以内に収まっている事(供給部ﾒﾝﾃﾅﾝｽﾗｲﾄとの干渉防止の為)",
"矢視A"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-112",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾘｰﾝｹｰﾌﾞﾙ空圧側配線",
"WorkItems": [
"1. 空圧部の配線配管を引き回接続する"
],
"WorkPoints": [
"ﾊﾞﾙﾌﾞ配線がﾌﾞﾗｹｯﾄから10㎜以内に収まっている事(供給部ﾒﾝﾃﾅﾝｽﾗｲﾄとの干渉防止の為)",
"矢視A"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words"... | {
"QualityItem": "配線引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:10.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾘｰﾝｹｰﾌﾞﾙ本体側配線",
"WorkItems": [
"1. ｸﾘｰﾝｹｰﾌﾞﾙ本体側の配線配管を引き回す"
],
"WorkPoints": [
"φ6白 →V21φ6黒 →P21",
"ICTR4RCN22K3131CN23K3131ICTR11R",
"目印ﾗﾍﾞﾙを貼付けておく"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "配線配管の引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾀﾝﾄﾞ部配線",
"WorkItems": [
"1. にCABLE を接続し引き回す"
],
"WorkPoints": [
"D1500"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :接続確認",
"1B10910R",
"ICTR10R",
"WWYJ-5300-1... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-112",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰ部配線",
"WorkItems": [
"1. ﾓｰﾀｰ配線を接続する",
"2. 全体を整線し結束する",
"3. 本体ﾄﾞｯｷﾝｸﾞ工程へ支給する"
],
"WorkPoints": [
"2.完成品",
"X517 BOLT",
"六角穴付きﾎﾞﾙﾄ M8×25(8P)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-112",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着移載ｲｵﾅｲｻﾞｰ部_(逆流れ)_組立①",
"WorkItems": [
"1. IONIZER の部品確認を行う",
"2. IONIZER にNOZZLE を取付ける",
"3. BRACKET に2完成品をBOLT で取付ける",
"4. 3完成品にSPEED-CONTROLLER をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ｲｵﾅｲｻﾞｰ付属ｹｰﾌﾞﾙ",
... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWXJ-5300-062",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着移載ｲｵﾅｲｻﾞｰ部_(逆流れ)_組立①",
"WorkItems": [
"1. IONIZER の部品確認を行う",
"2. IONIZER にNOZZLE を取付ける",
"3. BRACKET に2完成品をBOLT で取付ける",
"4. 3完成品にSPEED-CONTROLLER をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ｲｵﾅｲｻﾞｰ付属ｹｰﾌﾞﾙ",
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWXJ-5300-062",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "12㎜",
"ToolOther": "8.0N･m",
"WorkName": "仮圧着移載ｲｵﾅｲｻﾞｰ部_(逆流れ)_組立①",
"WorkItems": [
"1. IONIZER の部品確認を行う",
"2. IONIZER にNOZZLE を取付ける",
"3. BRACKET に2完成品をBOLT で取付ける",
"4. 3完成品にSPEED-CONTROLLER をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"･部... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "8.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着移載ｲｵﾅｲｻﾞｰ部_(逆流れ)_組立①",
"WorkItems": [
"1. IONIZER の部品確認を行う",
"2. IONIZER にNOZZLE を取付ける",
"3. BRACKET に2完成品をBOLT で取付ける",
"4. 3完成品にSPEED-CONTROLLER をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ｲｵﾅｲｻﾞｰ付属ｹｰﾌﾞﾙ",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "全閉から3回転開",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着移載ｲｵﾅｲｻﾞｰ部_(逆流れ)組立②",
"WorkItems": [
"1. をBRACKET にBOLT WASHER で取付ける",
"3. 2.完成品にCABLE-SUPPORT を取付ける",
"2. 1.完成品にCLIP をBOLT で取付ける"
],
"WorkPoints": [
"A矢視"
],
"Tolks": [],
"InspectionNo": "",
"Inspectio... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "仮圧着移載ｲｵﾅｲｻﾞｰ部_(逆流れ)_組立③",
"WorkItems": [
"1. を右記の寸法にｶｯﾄする",
"2. に1完成品を接続する",
"■3. 2完成品にCABLE をBOLT WASHER WASHER で取付ける",
"4. 3完成品にｲｵﾅｲｻﾞｰ付属ｹｰﾌﾞﾙを接続しLABEL TERMINAL PROCESS を取付ける",
"5. 配線配管をｲﾝｼｭﾛｯｸで固定する",
"... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "62cN･m",
"WorkName": "仮圧着移載ｲｵﾅｲｻﾞｰ部_(逆流れ)_組立③",
"WorkItems": [
"1. を右記の寸法にｶｯﾄする",
"2. に1完成品を接続する",
"■3. 2完成品にCABLE をBOLT WASHER WASHER で取付ける",
"4. 3完成品にｲｵﾅｲｻﾞｰ付属ｹｰﾌﾞﾙを接続しLABEL TERMINAL PROCESS を取付ける",
"5. 配線配管をｲﾝｼｭﾛｯｸで固定... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "62cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ1",
"WorkItems": [
"1. を で取付"
],
"WorkPoints": [
"寸法通り取付ける の合わせ面に隙間が無い事",
"2ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"271㎜",
"119㎜",
"119㎜... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ2",
"WorkItems": [
"1. に を で挟んで で取付"
],
"WorkPoints": [
"2ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "1/100",
"WorkName": "ﾌﾚｰﾑ3",
"WorkItems": [
"1. を定盤上でN015ﾌﾚｰﾑ上面の高さを測定する"
],
"WorkPoints": [
"2ｾｯﾄ測定",
"0.4㎜以内",
"P002の下面と定盤に隙間が無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.4㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-46",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ4",
"WorkItems": [
"1. に を で取付",
"2. に を で取付",
"3. 2.完成品に を取付",
"4. 3.完成品に を入れる"
],
"WorkPoints": [
" は方向あり",
"2ｾｯﾄ製作",
" の裏面に8個入れる",
" の表面に2個入れる位置は不問"
],
"Tolks": [],
"Inspect... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付け1",
"WorkItems": [
"1. に を貼付け"
],
"WorkPoints": [
"2ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾒﾓﾘとの合わせ基準",
"ﾒﾓﾘとの合わせ基準"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付け2",
"WorkItems": [
"1. に を貼付け"
],
"WorkPoints": [
"この範囲の貼付け寸法を明示右側も同じ",
"2ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"2㎜",
"5㎜",
"80㎜",
"5㎜",... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "銘板貼付け3",
"WorkItems": [
"1. に を貼付け",
"3. に を貼付け",
"4. に を取付ける",
"2. に を取付ける",
"1. に を貼付け",
"3. に を貼付け",
"4. に を取付ける",
"2. に を取付ける"
],
"WorkPoints": [
"2ｾｯﾄ製作",
" は【US】と【AM】の... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾝﾄﾞﾊﾞﾙﾌﾞ1",
"WorkItems": [
"1. を取付"
],
"WorkPoints": [
"16ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾊﾝﾄﾞﾊﾞﾙﾌﾞ2",
"WorkItems": [
"1. に を取付",
"2. 1.完成品に を で取付",
"3. 2.完成品に を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:10.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "治具",
"Size": "",
"ToolOther": "FM-6046",
"WorkName": "搬送PAD組立①",
"WorkItems": [
"1. BLOCK にVACUUM-PAD を仮取付(ﾅｯﾄはVACUUM-PAD の付属品を使用)",
"2. 1.完成品を㉗搬送PAD高さ合わせジグに取付"
],
"WorkPoints": [
"32ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Word... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6046",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "搬送PAD組立①",
"WorkItems": [
"3. PAD高さ調整を行う｡"
],
"WorkPoints": [
"29.8㎜±0.1",
"調整ボルト締結後、隙間に㉙０．１mmシクネスゲージが入ら無い事を確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表BLOC... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:29.8±0.1㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-46",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送PAD組立②",
"WorkItems": [
"▲1. に の付属品をADHESIVE ﾈｼﾞﾛｯｸ材で取付",
"▲2. 1.完成品上部の 付属品のﾌﾟﾗｸﾞを取り外し､JOINT をADHESIVE で取付 ｼﾞｮｲﾝﾄの向き注意"
],
"WorkPoints": [
"吸着穴に接着剤が混入し無い事",
"吸着穴に接着剤が混入し無い事",
"Φ30仕様(標準)時は､JOINT を選択",
"Φ15... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "WWYJ-5300-46",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessName": "特殊工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送PAD組立③",
"WorkItems": [
"▲1. に の付属品をﾈｼﾞﾛｯｸ材で取付"
],
"WorkPoints": [
"吸着穴に接着剤が混入し無い事",
"16ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"▲特殊作業",
"検査表 :AM2､ねじﾛｯｸ塗布",
... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "WWYJ-5300-46",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessName": "特殊工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "吸着ﾊﾝﾄﾞ組立1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"210㎜",
"210㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:210.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "吸着ﾊﾝﾄﾞ組立2",
"WorkItems": [
"1. を に で取付"
],
"WorkPoints": [
"2ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"85㎜"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "吸着ﾊﾝﾄﾞ組立3",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"5㎜",
"110㎜",
"110㎜",
"40㎜",
"40㎜",
"194㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "吸着ﾊﾝﾄﾞ組立4",
"WorkItems": [
"2. に1.完成品と を取付",
"3. 各配管を㉘で固定",
"1. ㉖配管を所定の長さに切断"
],
"WorkPoints": [
"2ｾｯﾄ製作",
"･150㎜･･･4本･460㎜･･･4本"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "吸着ﾊﾝﾄﾞ組立5",
"WorkItems": [
"▲1. に㉖を塗布し に取付"
],
"WorkPoints": [
" の中央部2本の爪は㉘で切断する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :P(1軸)2,接着剤塗布",
"▲特殊作業",
"接着剤塗布 小豆:2",
... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:2",
"Method": "目視",
"RecordMethod": "WWYJ-5300-46",
"Other": "ﾛｯｸﾀｲﾄ415",
"ProcessName": "特殊工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "次工程へ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1. を次工程へ"
]
} | {
"QualityItem": "払出確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り払い出されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾏｸﾞﾈｯﾄ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1. ﾊｰﾈｽﾎﾞｰﾄﾞにﾏｸﾞﾈｯﾄを取付ける",
"⇒ﾏｸﾞﾈｯﾄ中",
"⇒ﾏｸﾞﾈｯﾄ大"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊｰﾈｽ準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1.下記ﾘｽﾄの順番でｹｰﾌﾞﾙを準備する"
]
} | {
"QualityItem": "ｹｰﾌﾞﾙの準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"PCNEMG3A001",
"S203R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"PCNHTA001",
"CNSFA002",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回3",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"PCNOPA001",
"S001R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回4",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"BPCN24V23",
"POWERA102",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回5",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"DIOA101",
"PCNFAA001",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回6",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"PCN12V21A001",
"2G10851R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回7",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"PCN24V13A001",
"CN24VK3001",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回8",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"CPCN24V12",
"A-X2101",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回9",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"EPCN24V12/FPCN24V12",
"A-X2103",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回10",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"CNAFK3001",
"1B10110R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回11",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"CNTM1K3001",
"1B10C20R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回12",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"PCNCOV2A001",
"S321R/S329R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回13",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"PCNCOV1A001",
"S311",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回14",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"PCNCOV3A001",
"1S320R/S250R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回15",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"PCNCOV4A001",
"S323R/S326R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回16",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"FPCN24V23",
"A-X2101",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回17",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"PCN24V11A001",
"A-X2104",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回18",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"CN14K007/CN11K007/CN11K007//CN13K007",
"1G10710R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ﾊｰﾈｽ引き回19",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"RGBA101",
"CN1K3140",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6476",
"WorkName": "ｲﾝｼｭﾛｯｸ固定",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1. ｲﾝｼｭﾛｯｸで固定する",
"⇒100mm",
"⇒150mm",
"⇒200mm",
"⇒250mm"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6476",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6478",
"WorkName": "ﾏｸﾞﾈｯﾄ取付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1. ﾊｰﾈｽﾎﾞｰﾄﾞにﾏｸﾞﾈｯﾄを取付ける",
"⇒ﾏｸﾞﾈｯﾄ中",
"⇒ﾏｸﾞﾈｯﾄ大"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6478",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊｰﾈｽ準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1.下記ﾘｽﾄの順番でｹｰﾌﾞﾙを準備する"
]
} | {
"QualityItem": "ｹｰﾌﾞﾙの準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6478",
"WorkName": "ﾊｰﾈｽ引き回1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"B-X2101",
"CN1K3131",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6478",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6478",
"WorkName": "ﾊｰﾈｽ引き回2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"D-X2101",
"CN5K3012",
"CN1K3007",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6478",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6478",
"WorkName": "ﾊｰﾈｽ引き回3",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"CN15K009/CN5K009",
"ICTR11P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6478",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6478",
"WorkName": "ﾊｰﾈｽ引き回4",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"CN13K009",
"ICTR10P",
"CN16K010",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6478",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6478",
"WorkName": "ﾊｰﾈｽ引き回5",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"CN3K3100",
"ACF7R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6478",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6478",
"WorkName": "ﾊｰﾈｽ引き回6",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"CN3K3101/CN4K3101",
"MMU7R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6478",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6478",
"WorkName": "ﾊｰﾈｽ引き回7",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"CN11K009",
"CN11K009P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6478",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6478",
"WorkName": "ﾊｰﾈｽ引き回8",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1TB1K012/2TB1K012",
"ACF15R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6478",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6478",
"WorkName": "ﾊｰﾈｽ引き回9",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"3TB1K012/4TB1K012",
"ACF16R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6478",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6478",
"WorkName": "ﾊｰﾈｽ引き回10",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"CH1A002",
"ACF5R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6478",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6478",
"WorkName": "ﾊｰﾈｽ引き回11",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"CH2A002",
"ACF6R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6478",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.