input stringclasses 1
value | instruction stringlengths 202 3.29k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "MMUﾌﾞﾗｹｯﾄ組立(逆流れ)",
"WorkItems": [
"★1. BRACKET に をBOLT WASHER で取付け､CABLE-SUPPORT を挿し込む",
"2. 1.完成品裏面にCABLE ｺﾈｸﾀを挿し､抵抗をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words":... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "静電対策工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LED基板組立①(逆流れ)",
"WorkItems": [
"1. BRACKET にPLATE をBOLT で取付ける",
"2. 1.完成品にSHEET を敷き､SHEET をPLATE 上面に貼付ける"
],
"WorkPoints": [
"PLATE を包み込むようにSHEET を貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指定の位置に貼付けている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LED基板組立②(逆流れ)",
"WorkItems": [
"★1. に をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"正流れ･逆流れで基板配置が変わるので注意すること",
"逆流れ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"★静電対策作業",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-103",
"Other": "-",
"ProcessName": "静電対策工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾗｲﾊﾞｰLANｹｰﾌﾞﾙﾀｸﾞ取付(逆流れ)",
"WorkItems": [
"1. CABLE CABLE CABLE CABLE CABLE CABLE にMARK TUBE TERMINAL PROCESS を結束する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"X2AK4122"... | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "回生抵抗組立(逆流れ)",
"WorkItems": [
"1. PLATE に をSPACER WASHER BOLT にて取付ける",
"2. 1.の完成品に ををBOLT WASHER にて取付ける",
"3. PLATE に をBOLT WASHER にて取付ける",
"4. PLATE に をBOLT WASHER にて取付ける"
],
"WorkPoints": [
"ALXRM4112P",
"SU... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立①(逆流れ)",
"WorkItems": [
"1. BRACKET に をBOLT WASHER にて取付ける",
"2. にBOLT をCLIP で取付ける"
],
"WorkPoints": [
"K4101SUX軸"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立②(逆流れ)",
"WorkItems": [
"2. 1.の完成品に をBOLT WASHER にて取付ける",
"1. BRACKET にSPACER をBOLT WASHER にて取付ける",
"3. 2.完成品に をBOLT WASHER にて取付ける",
"4. 3.完成品の両端のﾄﾞﾗｲﾊﾞｰにBOLT をCLIP で取付ける"
],
"WorkPoints": [
"K4117ARY... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立③(逆流れ)",
"WorkItems": [
"1. BRACKET に をBOLT WASHER にて取付ける"
],
"WorkPoints": [
"K4114ALZ軸",
"K4115ALV軸",
"K4113ALY軸"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立④(逆流れ)",
"WorkItems": [
"1. の両端のﾄﾞﾗｲﾊﾞｰにBOLT をCLIP で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立⑤(逆流れ)",
"WorkItems": [
"3. 2.完成品の両端のﾄﾞﾗｲﾊﾞｰにBOLT をCLIP で取付ける",
"2. 1.の完成品に をBOLT WASHER にて取付ける",
"1. BRACKET にSPACER をBOLT WASHER にて取付ける"
],
"WorkPoints": [
"K4126MRX軸",
"K4102SMX軸",
"K4112ALX軸"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立⑥(逆流れ)",
"WorkItems": [
"1. に をBOLT WASHER にて取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立⑦(逆流れ)",
"WorkItems": [
"1. BRACKET に をBOLT WASHER にて取付ける",
"2.1.完成品の両端のﾄﾞﾗｲﾊﾞｰにBOLT でCLIP を取付ける"
],
"WorkPoints": [
"K4128MRZ軸",
"K4129MRV軸",
"K4127MRY軸"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立⑧(逆流れ)",
"WorkItems": [
"1. BRACKET に をBOLT WASHER にて取付ける",
"2.1.完成品の両端のﾄﾞﾗｲﾊﾞｰにBOLT でCLIP を取付ける"
],
"WorkPoints": [
"K4124MLZ軸",
"K4125MLV軸",
"K4123MLY軸"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立⑨(逆流れ)",
"WorkItems": [
"1. BRACKET に をBOLT WASHER にて取付ける",
"2.1.完成品の両端のﾄﾞﾗｲﾊﾞｰにBOLT でCLIP を取付ける"
],
"WorkPoints": [
"K4131AHRX軸",
"K4130AHLX軸",
"K4104ARF軸",
"K4103ALF軸"
],
"Tolks": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立⑩(逆流れ)",
"WorkItems": [
"1. BRACKET に をBOLT WASHER にて取付ける",
"2.1.完成品の両端のﾄﾞﾗｲﾊﾞｰにBOLT でCLIP を取付ける"
],
"WorkPoints": [
"K4108IH軸",
"K4110ITY軸",
"K4111ITV軸"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-102",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立⑪(逆流れ)",
"WorkItems": [
"3. 2.の完成品の両端のﾄﾞﾗｲﾊﾞｰにBOLT でCLIP を取付ける",
"1. BRACKET にSPACER をBOLT WASHER にて取付ける",
"2. 1.の完成品に をBOLT WASHER にて取付ける"
],
"WorkPoints": [
"K4106MHV軸",
"K4105MH軸",
"K4122MLX軸"... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-102",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立⑫(逆流れ)(ITXのOPありの場合)",
"WorkItems": [
"1. に をBOLT WASHER にて取付ける",
"2. 1.完成品のﾏｳﾝﾄを端へ移動する"
],
"WorkPoints": [
"K4107MTY軸",
"K4106MHV軸",
"K4122MLX軸",
"K4105MH軸",
"K4109ITX軸"
],
"Tolks": [... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立⑬(逆流れ)",
"WorkItems": [
"1. に をBOLT WASHER にて取付ける",
"2. 1.完成品のﾏｳﾝﾄを端へ移動する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立⑭(逆流れ)",
"WorkItems": [
"1. に を接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :ｺﾈｸﾀ接続確認",
"X2BK4119",
"X2AK4119",
"X2AK4118",
"... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-102",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立⑮(逆流れ)",
"WorkItems": [
"1. に を接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :ｺﾈｸﾀ接続確認",
"X2BK4125",
"X2AK4125",
"X2BK4123",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-102",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾞﾚｰｶｰBOX組立①(逆流れ)",
"WorkItems": [
"▲2. BRACKET にBUSH を接着する",
"1. BRACKET にLABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"接着剤塗布 米粒:2",
"▲特殊作業"
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "特殊工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾚｰｶｰBOX組立①(逆流れ)",
"WorkItems": [
"▲2. BRACKET にBUSH を接着する",
"1. BRACKET にLABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"10㎜",
"▲特殊作業",
"接着剤塗布 米粒... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ415",
"ProcessName": "特殊工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾚｰｶｰBOX組立②(逆流れ)",
"WorkItems": [
"1. にSCREW をBOLT WASHER で取付ける",
"2. 1.完成品に を付属ﾎﾞﾙﾄで取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾚｰｶｰBOX組立③(逆流れ)",
"WorkItems": [
"1. BRACKET にBUSH をBOLT WASHER で取付",
"3. 2.完成品にBUSH をBOLT WASHER で取付ける",
"2. に1.完成品をBOLT WASHER で取付ける",
"4. 3.完成品にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"Inspec... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾚｰｶｰBOX配線(逆流れ)",
"WorkItems": [
"■2. にCABLE ｹｰﾌﾞﾙ端子を通し､ｻｰｼﾞｷﾗｰ端子とｱｰｽﾌﾟﾚｰﾄにSCREW にて接続する",
"■1. にCABLE ｹｰﾌﾞﾙ端子を通し､ ﾌﾞﾚｰｶｰ二次側にｻｰｼﾞｷﾗｰ端子と共に接続する",
"3. 2.完成品に を取付け整線する"
],
"WorkPoints": [
"CABLE CABLE ｹｰﾌﾞﾙを 抜き穴を通しておく事",... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-102",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "2.5N･m",
"WorkName": "ﾌﾞﾚｰｶｰBOX配線(逆流れ)",
"WorkItems": [
"■2. にCABLE ｹｰﾌﾞﾙ端子を通し､ｻｰｼﾞｷﾗｰ端子とｱｰｽﾌﾟﾚｰﾄにSCREW にて接続する",
"■1. にCABLE ｹｰﾌﾞﾙ端子を通し､ ﾌﾞﾚｰｶｰ二次側にｻｰｼﾞｷﾗｰ端子と共に接続する"
],
"WorkPoints": [
"CABLE CABLE ｹｰﾌﾞﾙを 抜き穴を通しておく事",
"ｶ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.5N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "1.8N･m",
"WorkName": "ﾌﾞﾚｰｶｰBOX配線(逆流れ)",
"WorkItems": [
"■2. にCABLE ｹｰﾌﾞﾙ端子を通し､ｻｰｼﾞｷﾗｰ端子とｱｰｽﾌﾟﾚｰﾄにSCREW にて接続する",
"■1. にCABLE ｹｰﾌﾞﾙ端子を通し､ ﾌﾞﾚｰｶｰ二次側にｻｰｼﾞｷﾗｰ端子と共に接続する"
],
"WorkPoints": [
"CABLE CABLE ｹｰﾌﾞﾙを 抜き穴を通しておく事",
"ｶ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.8N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "FAN組立②(架台内、組立②)逆流れ",
"WorkItems": [
"2. ｹｰﾌﾞﾙの固定"
],
"WorkPoints": [
"FANのﾌﾚｰﾑ部へ固定する",
"･FAN本体部取付ﾎﾞﾙﾄ･ﾜｯｼｬWASHER BOLT を各8個準備し付属する事･BRACKET 本体取付用ﾎﾞﾙﾄ･ﾜｯｼｬWASHER BOLT を各8個準備し付属する事",
"4個作成する",
"右向き1個､左向き3個を作成す... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:30.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN組立③(架台内、ﾀｸﾞ取付け)逆流れ",
"WorkItems": [
"1. にMARK TUBE TERMINAL PROCESS ﾀｸﾞを結束する"
],
"WorkPoints": [
"合わせる",
"1ｾｯﾄ",
"4ｾｯﾄ",
"G10733R",
"G10734R",
"G10735R",
"G10742R",
"G10743R",
"3ｾｯﾄ... | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼｰﾄｶｾｯﾄ部(ｼｰﾄ幅230㎜)組立て①",
"WorkItems": [
"1. HOLDER にPIN を圧入する"
],
"WorkPoints": [
"出代:9㎜",
"写真は､実際のHOLDERと少し形状が異なりますが､PIN圧入作業は同じです"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "9.0±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｰﾄｶｾｯﾄ部(ｼｰﾄ幅230㎜)組立て②",
"WorkItems": [
"1. SHAFT にCOLLAR をBOLT で取付ける",
"2. 1.完成品にWASHER を挿入する",
"3. 2.完成品に を挿入する"
],
"WorkPoints": [
"SHAFT の段付きまでCOLLAR を挿入し固定する",
"段付き",
"完成図"
],
"Tolks": [],
"Insp... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｰﾄｶｾｯﾄ部(ｼｰﾄ幅230㎜)組立て③",
"WorkItems": [
"1. にTORQUE-LIMITER BLOCK SHIM BEARING の順に挿入しBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"挿入"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｰﾄｶｾｯﾄ部(ｼｰﾄ幅230㎜)組立て④",
"WorkItems": [
"1. にPIN を取付ける",
"2. 1.完成品にSHAFT をSCREW で取付ける"
],
"WorkPoints": [
"矢視A"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"矢視A"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｰﾄｶｾｯﾄ部(ｼｰﾄ幅230㎜)組立て⑤",
"WorkItems": [
"1. にHOLDER をBOLT で取付ける",
"2. 1.完成品にC-RING を挿入する",
"3. 2.完成品にBEARING を圧入しBOLT WASHER で取付ける",
"4. 3.完成品にSHAFT を挿入しC-RING を取付ける"
],
"WorkPoints": [
"ｴｯｼﾞ面をHOLDER の方に向けること",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｰﾄｶｾｯﾄ部(ｼｰﾄ幅230㎜)組立て⑥",
"WorkItems": [
"1. にHOLDER を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾞｯｸｱｯﾌﾟﾍﾞｰｽｾﾗﾐｯｸﾌﾟﾚｰﾄ設置",
"WorkItems": [
"1. にPLATE を設置する"
],
"WorkPoints": [
"同時加工品をｾｯﾄで使用する(1ｾｯﾄ4部品)",
"18㎜(幅小さい)",
"20㎜",
"20㎜",
"15㎜(幅小さい)",
"20㎜",
"20㎜",
"18㎜(幅小さい)",
"ﾌﾟﾚｰﾄ設置位置に注意す... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾞｯｸｱｯﾌﾟﾍﾞｰｽﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. BLOCK を砥石にかける",
"◆2. 1.完成品を にBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ﾌﾞﾛｯｸ全体に砥石をかけ､打痕･ﾊﾞﾘ･ｶｴﾘの無い事を確認する",
"BOLT ﾎﾞﾙﾄに耐熱ｸﾞﾘｰｽを塗布する",
"ﾋﾟﾝに当付ける",
"ﾋﾟﾝに当付ける",
"... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽﾓﾘｺｰﾄ1000",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾊﾞｯｸｱｯﾌﾟﾍﾞｰｽﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. BLOCK を砥石にかける",
"◆2. 1.完成品を にBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ﾌﾞﾛｯｸ全体に砥石をかけ､打痕･ﾊﾞﾘ･ｶｴﾘの無い事を確認する",
"BOLT ﾎﾞﾙﾄに耐熱ｸﾞﾘｰｽを塗布する",
"ﾋﾟﾝに当付ける",
"ﾋﾟﾝに... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ﾊﾞｯｸｱｯﾌﾟﾍﾞｰｽﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. BLOCK を砥石にかける",
"◆2. 1.完成品を にBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ﾌﾞﾛｯｸ全体に砥石をかけ､打痕･ﾊﾞﾘ･ｶｴﾘの無い事を確認する",
"BOLT ﾎﾞﾙﾄに耐熱ｸﾞﾘｰｽを塗布する",
"ﾋﾟﾝに当付ける",
"... | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.01㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾙﾀﾞｰ組立",
"WorkItems": [
"1. を砥石にかける",
"2. 1.完成品に ｶﾌﾟﾄﾝﾃｰﾌﾟを貼付ける"
],
"WorkPoints": [
"ﾌﾞﾛｯｸ全体に砥石をかけ､打痕･ﾊﾞﾘ･ｶｴﾘの無い事を確認する",
"ｶﾌﾟﾄﾝﾃｰﾌﾟ",
"貼付け面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾙﾀﾞｰﾊﾞｯｸｱｯﾌﾟﾂｰﾙ取付",
"WorkItems": [
"◆1. にSTAGE STAGE を BOLT で仮固定する"
],
"WorkPoints": [
"下記同一Noの部品は各機種毎の部材で同一作業を実施する",
"STAGE (ｶﾞﾗｽ製)STAGE (SUS製)は仕様通り取付ける",
"SD-A044411-005で固定",
"同時加工品をｾｯﾄで使用する(1ｾｯﾄ2部品)",
"B... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽﾓﾘｺｰﾄ1000",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾞｯｸｱｯﾌﾟﾂｰﾙ固定",
"WorkItems": [
"1. のﾎﾙﾀﾞｰとﾊﾞｯｸｱｯﾌﾟﾂｰﾙ部を固定する"
],
"WorkPoints": [
"ﾎﾙﾀﾞｰとﾊﾞｯｸｱｯﾌﾟﾂｰﾙを位置決め後､仮止めしていたﾎﾞﾙﾄで固定する",
"ﾎﾙﾀﾞｰをﾊﾞｯｸｱｯﾌﾟﾂｰﾙに押し当てて固定する",
"矢印方向にﾊﾞｯｸｱｯﾌﾟﾂｰﾙを押し当てて取付ける",
"ﾎﾙﾀﾞｰ",
"ﾊﾞｯｸｱｯﾌﾟﾂｰﾙ"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/1000",
"ToolOther": "",
"WorkName": "ﾊﾞｯｸｱｯﾌﾟﾍﾞｰｽ平面度測定",
"WorkItems": [
"1. ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞの平面度を測定する"
],
"WorkPoints": [
"5μm以下(各区間での最大最小の差)",
"50㎜間隔で測定",
"定盤",
"ｽﾃｰｼﾞ上面(ﾊﾞｯｸｱｯﾌﾟﾂｰﾙ上面)"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "5μm以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-067",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾊﾞｯｸｱｯﾌﾟﾍﾞｰｽ平面度測定",
"WorkItems": [
"1. ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞの平面度を測定する"
],
"WorkPoints": [
"5μm以下(各区間での最大最小の差)",
"50㎜間隔で測定",
"定盤",
"ｽﾃｰｼﾞ上面(ﾊﾞｯｸｱｯﾌﾟﾂｰﾙ上面)"
],
"Tolks": [],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "50㎜間隔で測定",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾋｰﾀｰ取付",
"WorkItems": [
"■1. HEATER の仕様確認とLot No.を記載する",
"◆2. 1.完成品を にSCREW で取付ける"
],
"WorkPoints": [
"ﾋｰﾀｰ仕様:200V700Wを確認する",
"SCREW 止めﾈｼﾞの先端に耐熱ｸﾞﾘｰｽを塗布する",
"ﾋｰﾀｰ出代に注意する",
"両端から挿入",
"出代: 5㎜",
"出代: 5... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-067",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾋｰﾀｰ取付",
"WorkItems": [
"■1. HEATER の仕様確認とLot No.を記載する",
"◆2. 1.完成品を にSCREW で取付ける"
],
"WorkPoints": [
"ﾋｰﾀｰ仕様:200V700Wを確認する",
"SCREW 止めﾈｼﾞの先端に耐熱ｸﾞﾘｰｽを塗布する",
"ﾋｰﾀｰ出代に注意する",
"両端から挿入",
"出代: 5㎜",
"出代: 5... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-067",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾋｰﾀｰ取付",
"WorkItems": [
"■1. HEATER の仕様確認とLot No.を記載する",
"◆2. 1.完成品を にSCREW で取付ける"
],
"WorkPoints": [
"ﾋｰﾀｰ仕様:200V700Wを確認する",
"SCREW 止めﾈｼﾞの先端に耐熱ｸﾞﾘｰｽを塗布する",
"ﾋｰﾀｰ出代に注意する",
"両端から挿入",
"出代: 5㎜",
"出代: 5... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽﾓﾘｺｰﾄ1000",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾋｰﾀｰ取付",
"WorkItems": [
"■1. HEATER の仕様確認とLot No.を記載する",
"◆2. 1.完成品を にSCREW で取付ける"
],
"WorkPoints": [
"ﾋｰﾀｰ仕様:200V700Wを確認する",
"SCREW 止めﾈｼﾞの先端に耐熱ｸﾞﾘｰｽを塗布する",
"ﾋｰﾀｰ出代に注意する",
"両端から挿入",
"出代: 5㎜",
... | {
"QualityItem": "ﾋｰﾀｰ出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "右側出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾋｰﾀｰ取付",
"WorkItems": [
"■1. HEATER の仕様確認とLot No.を記載する",
"◆2. 1.完成品を にSCREW で取付ける"
],
"WorkPoints": [
"ﾋｰﾀｰ仕様:200V700Wを確認する",
"SCREW 止めﾈｼﾞの先端に耐熱ｸﾞﾘｰｽを塗布する",
"ﾋｰﾀｰ出代に注意する",
"両端から挿入",
"出代: 5㎜",
... | {
"QualityItem": "ﾋｰﾀｰ出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "左側出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "温度ﾋｭｰｽﾞ固定ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"◆1. にBRACKET をWASHER BOLT で取付ける"
],
"WorkPoints": [
" とBRACKET の間にWASHER を挟み込む",
"BOLT ﾎﾞﾙﾄに耐熱ｸﾞﾘｰｽを塗布する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽﾓﾘｺｰﾄ1000",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "温度ﾋｭｰｽﾞ安全部品確認",
"WorkItems": [
"■1. CABLE CABLE の型式確認を行う",
"2. CABLE CABLE にGUIDE をｾｯﾄする"
],
"WorkPoints": [
"型式は温度ﾋｭｰｽﾞの刻印を確認する事",
"温度ﾋｭｰｽﾞの刻印部",
"GUIDE のｾｯﾄ位置に注意する",
"ﾋｭｰｽﾞの上にGUIDE をｾｯﾄ(端子にかから無い事)"
],
... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-128",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "温度ﾋｭｰｽﾞﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞ取付",
"WorkItems": [
"◆1. に をBOLT で取付ける"
],
"WorkPoints": [
"BOLT ﾎﾞﾙﾄに耐熱ｸﾞﾘｰｽを塗布する",
"F0037P",
"F0039P",
" 取付け位置と配線の方向に注意する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems"... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽﾓﾘｺｰﾄ1000",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "温度ﾋｭｰｽﾞ押さえﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. にBRACKET をBOLT で取付ける"
],
"WorkPoints": [
"BRACKET の取付け方向に注意する",
"温度ﾋｭｰｽﾞのｹｰﾌﾞﾙを押さえて固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "熱電対取付",
"WorkItems": [
"■1. THERMO-COUPLE の型式確認とｼﾘｱﾙNO.を記入する",
"◆2. 1.完成品を にSCREW で取付ける",
"3. 熱電対の配線をSD-A044411-011のP605 BRACKET で固定する"
],
"WorkPoints": [
"型式:TS-6-K-S-2-1.0-B-316-300-NDP-PT3-10-RT",
"ｼﾘｱﾙNO.",
... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-067",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "熱電対取付",
"WorkItems": [
"■1. THERMO-COUPLE の型式確認とｼﾘｱﾙNO.を記入する",
"◆2. 1.完成品を にSCREW で取付ける",
"3. 熱電対の配線をSD-A044411-011のP605 BRACKET で固定する"
],
"WorkPoints": [
"型式:TS-6-K-S-2-1.0-B-316-300-NDP-PT3-10-RT",
"ｼﾘｱﾙNO.",
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-067",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "熱電対取付",
"WorkItems": [
"■1. THERMO-COUPLE の型式確認とｼﾘｱﾙNO.を記入する",
"◆2. 1.完成品を にSCREW で取付ける",
"3. 熱電対の配線をSD-A044411-011のP605 BRACKET で固定する"
],
"WorkPoints": [
"型式:TS-6-K-S-2-1.0-B-316-300-NDP-PT3-10-RT",
"ｼﾘｱﾙNO.",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽﾓﾘｺｰﾄ1000",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾈｸﾀﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. にBRACKET をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙｻﾎﾟｰﾄFT4取付",
"WorkItems": [
"1. にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PL警告ﾗﾍﾞﾙ(高温注意)貼付",
"WorkItems": [
"■1. LABEL の型式確認を行う",
"■2. 1.完成品を に貼付ける"
],
"WorkPoints": [
"型式:PC010301",
"±2㎜以下",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems"... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-017",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "PL警告ﾗﾍﾞﾙ(高温注意)貼付",
"WorkItems": [
"■1. LABEL の型式確認を行う",
"■2. 1.完成品を に貼付ける"
],
"WorkPoints": [
"型式:PC010301",
"±2㎜以下",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "",
"Inspectio... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙﾀｸﾞ取付",
"WorkItems": [
"1. のｹｰﾌﾞﾙにLABEL TERMINAL PROCESS を取付ける"
],
"WorkPoints": [
"E10803P(L側)",
"E10805P(R側)",
"B40803P(L側)",
"B40805P(R側)",
"F0037P(L側)",
"F0039P(R側)",
"背面",
"L側",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾈﾙｽﾃｰｼﾞ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰ組立①",
"WorkItems": [
"1. BRACKET に砥石をかける"
],
"WorkPoints": [
"全体に砥石をかけ､ﾊﾞﾘ･ｶｴﾘ等無い事を確認する",
"裏面側(ﾌﾚｰﾑへの取付け面)",
"裏面側(ﾓｰﾀｰ取付け面)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰ組立②",
"WorkItems": [
"■1. MOTOR の型式確認とｼﾘｱﾙNO.を記入する",
"2. 1.完成品を にBOLT で取付ける"
],
"WorkPoints": [
"型式:PK543AW-A83",
"ｼﾘｱﾙNO."
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-070",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰ組立②",
"WorkItems": [
"■1. MOTOR の型式確認とｼﾘｱﾙNO.を記入する",
"2. 1.完成品を にBOLT で取付ける"
],
"WorkPoints": [
"型式:PK543AW-A83",
"ｼﾘｱﾙNO."
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-070",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "5.5㎜",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰ組立③",
"WorkItems": [
"1. にGEAR をSCREW で取付ける",
"2. 1.完成品にLABEL TERMINAL PROCESS を取付ける"
],
"WorkPoints": [
"GEAR ｷﾞｱとﾌﾞﾗｹｯﾄの間に､5.5㎜のﾌﾞﾛｯｸｹﾞｰｼﾞを挟んで固定する",
"ｷﾞｱ高さ 24.5㎜を確認する",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ 5.5㎜",
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:5.5㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰ組立③",
"WorkItems": [
"1. にGEAR をSCREW で取付ける",
"2. 1.完成品にLABEL TERMINAL PROCESS を取付ける"
],
"WorkPoints": [
"GEAR ｷﾞｱとﾌﾞﾗｹｯﾄの間に､5.5㎜のﾌﾞﾛｯｸｹﾞｰｼﾞを挟んで固定する",
"ｷﾞｱ高さ 24.5㎜を確認する",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ 5.5㎜",
"ﾓｰﾀｼｬ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:24.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰ組立④",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｰﾄ送りﾍﾞｰｽ組立",
"WorkItems": [
"1. BRACKET に砥石をかける"
],
"WorkPoints": [
"指示箇所に砥石をかけ､ﾊﾞﾘ･ｶｴﾘ等無い事を確認する",
"下面全体に砥石をかける",
"凸部､加工面に砥石をかける",
"2個作製"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ取付右側",
"WorkItems": [
"1. にPLATE をBOLT で取付ける"
],
"WorkPoints": [
"取付ﾈｼﾞ穴",
"短い",
"長い",
" の段差に当付け",
"ｼｯｸﾈｽｹﾞｰｼﾞで隙間確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.01㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ取付左側",
"WorkItems": [
"1. にPLATE をBOLT で取付ける"
],
"WorkPoints": [
"取付ﾈｼﾞ穴",
"短い",
"長い",
" の段差に当付け",
"ｼｯｸﾈｽｹﾞｰｼﾞで隙間確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.01㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ取付右側",
"WorkItems": [
"1. にGUIDE をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ下側に面位置で取付ける",
"取付方向に注意する",
"ﾌﾟﾚｰﾄ下側に面位置で取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ取付左側",
"WorkItems": [
"1. にGUIDE をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ下側に面位置で取付ける",
"取付方向に注意する",
"ﾌﾟﾚｰﾄ下側に面位置で取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "7㎜",
"ToolOther": "50cN･m",
"WorkName": "ﾌﾟﾗﾝｼﾞｬｰ取付右側",
"WorkItems": [
"1. BLOCK にPLUNGER をNUT で取付ける"
],
"WorkPoints": [
"1.5㎜程度で固定する",
"ﾌﾟﾗﾝｼﾞｬｰの締付けに注意する"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾗﾝｼﾞｬｰ取付右側",
"WorkItems": [
"1. BLOCK にPLUNGER をNUT で取付ける"
],
"WorkPoints": [
"1.5㎜程度で固定する",
"ﾌﾟﾗﾝｼﾞｬｰの締付けに注意する"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:1.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｯｸ取付右側",
"WorkItems": [
"1. に をBOLT で取付ける"
],
"WorkPoints": [
"ﾌﾞﾛｯｸのｶｯﾄ面(左側へ向く)",
"上下は段付き部分に当付け固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻｰ取付右側",
"WorkItems": [
"1. BRACKET にSENSOR をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻｰﾌﾞﾗｹｯﾄ取付右側",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"右側のみｾﾝｻｰﾌﾞﾗｹｯﾄ取付",
"面合わせで取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "7㎜",
"ToolOther": "50cN･m",
"WorkName": "ﾌﾟﾗﾝｼﾞｬｰ取付左側",
"WorkItems": [
"1. BLOCK にPLUNGER をNUT で取付ける"
],
"WorkPoints": [
"1.5㎜程度で固定する",
"ﾌﾟﾗﾝｼﾞｬｰの締付けに注意する"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾗﾝｼﾞｬｰ取付左側",
"WorkItems": [
"1. BLOCK にPLUNGER をNUT で取付ける"
],
"WorkPoints": [
"1.5㎜程度で固定する",
"ﾌﾟﾗﾝｼﾞｬｰの締付けに注意する"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:1.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｯｸ取付左側",
"WorkItems": [
"1. に をBOLT で取付ける"
],
"WorkPoints": [
"ﾌﾞﾛｯｸのｶｯﾄ面(右側へ向く)",
"上下は段付き部分に当付け固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｱﾘﾝｸﾞﾌﾟﾚｰﾄﾋﾟﾝ圧入",
"WorkItems": [
"1. PLATE にPIN を圧入する"
],
"WorkPoints": [
"2個作製",
"出代: 5㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｱﾘﾝｸﾞ取付",
"WorkItems": [
"1. にBEARING を取付ける"
],
"WorkPoints": [
"左右対称にする",
"K017-1(右側用)",
"K017-2(左側用)",
"裏面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｱﾘﾝｸﾞﾌﾟﾚｰﾄ取付右側",
"WorkItems": [
"1. に をBOLT で取付ける"
],
"WorkPoints": [
"面合わせで取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｱﾘﾝｸﾞﾌﾟﾚｰﾄ取付左側",
"WorkItems": [
"1. に をBOLT で取付ける"
],
"WorkPoints": [
"面合わせで取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾈｸﾀﾌﾞﾗｹｯﾄ取付右側",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾈｸﾀﾌﾞﾗｹｯﾄ取付左側",
"WorkItems": [
"1. に を で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾗｲﾄﾞﾚｰﾙ組立①右側",
"WorkItems": [
"1. SLIDE-RAIL にPLATE をSCREW で取付ける",
"2. 1.完成品にBLOCK をBOLT WASHER で取付ける"
],
"WorkPoints": [
"裏側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾗｲﾄﾞﾚｰﾙ組立②右側",
"WorkItems": [
"1. にBRACKET をSCREW で取付ける",
"2. に1.完成品をBOLT WASHER で取付ける"
],
"WorkPoints": [
"裏側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾗｲﾄﾞﾚｰﾙ組立①左側",
"WorkItems": [
"1. SLIDE-RAIL にPLATE をSCREW で取付ける",
"2. 1.完成品にBLOCK をBOLT WASHER で取付ける"
],
"WorkPoints": [
"裏側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾗｲﾄﾞﾚｰﾙ組立②左側",
"WorkItems": [
"1. に を で取付ける",
"2. に1.完成品を で取付ける"
],
"WorkPoints": [
"裏側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾗﾝｼﾞｬｰﾌﾞﾗｹｯﾄ組立①右側",
"WorkItems": [
"2. 1.完成品にPLATE をBOLT WASHER で取付ける",
"3. 2.完成品にPLUNGER を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "出代:6.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾟﾗﾝｼﾞｬｰﾌﾞﾗｹｯﾄ組立②右側",
"WorkItems": [
"1. にBEARING をNUT で取付ける",
"2. 1.完成品にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"裏側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾗﾝｼﾞｬｰﾌﾞﾗｹｯﾄ組立①左側",
"WorkItems": [
"2. 1.完成品にPLATE をBOLT WASHER で取付ける",
"3. 2.完成品にPLUNGER を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "出代:6.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾟﾗﾝｼﾞｬｰﾌﾞﾗｹｯﾄ組立②左側",
"WorkItems": [
"1. にBEARING をNUT で取付ける",
"2. 1.完成品にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"裏側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻｰ取付①",
"WorkItems": [
"1. にSENSOR を付属ねじで取付ける",
"2. 1.完成品にLABEL TERMINAL PROCESS を取付ける"
],
"WorkPoints": [
"ｾﾝｻｰの投光(白線)､受光(黒線)に注意する事",
"受光(黒線)",
"投光(白線)",
"付属ねじ",
"1B10630-7R",
"1B10630-8R",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻｰ取付②",
"WorkItems": [
"1. のｾﾝｻｰ配線を結束する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付",
"WorkItems": [
"■1. LABEL の型式確認を行う",
"■2. にLABEL を貼付ける",
"3. 2.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"型式:PC011201",
"±2㎜以下",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-017",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付",
"WorkItems": [
"■1. LABEL の型式確認を行う",
"■2. にLABEL を貼付ける",
"3. 2.完成品にLABEL を貼付ける",
"■1. LABEL の型式確認を行う",
"■2. にLABEL を貼付ける",
"3. 2.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"型式:PC011201",
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜以下",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "引き渡し準備",
"WorkItems": [
"1. COVER SCREW BOLT WASHER BOLT BOLT WASHER を本圧着加圧ﾌﾚｰﾑ部に引き渡す"
],
"WorkPoints": [
"ﾓｰﾀｰ組立品",
"ｼｰﾄ送りｽﾗｲﾄﾞﾚｰﾙ組立品",
"右側",
"左側",
"ｾﾝｻｰ部組立品"
],
"Tolks": [],
"InspectionNo": "",... | {
"QualityItem": "払出確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り払い出されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.