input stringclasses 1
value | instruction stringlengths 202 3.29k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "操作SW・ﾌﾗｯﾄｹｰﾌﾞﾙ(太)取付け",
"WorkItems": [
"2. ケーブル関係を㉘でとめる",
"3. ﾌﾗｯﾄｹｰﾌﾞﾙを折り曲げる",
"1. SWITCH にCABLE を取付けてから にSCREW で取付ける"
],
"WorkPoints": [
"先にCABLE と をSWITCH のｺﾈｸﾀに接続し青ﾏｰｷﾝｸﾞする",
"ﾌﾚｰﾑへの乗り上げﾌﾗｯﾄｹｰﾌﾞﾙ折曲がり等注意のこと",
... | {
"QualityItem": "負荷確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｹｰﾌﾞﾙに負荷がかかって無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾗｯﾄｹｰﾌﾞﾙ配線(太)",
"WorkItems": [
"★1. のﾌﾗｯﾄｹｰﾌﾞﾙを引き回し､基板に接続する"
],
"WorkPoints": [
"突き当たりまで押し込んでﾛｯｸする(ｺﾈｸﾀｰに対して傾きが無い事)",
"接続後､青ﾏｰｷﾝｸﾞ",
"ﾌﾚｰﾑ下側を通す",
"一度折り曲げた箇所は開かないこと",
"細いﾌﾗｯﾄｹｰﾌﾞﾙに重ならないように折り曲げる",
"端子面を下... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "静電対策工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾗｯﾄｹｰﾌﾞﾙ配線(太)",
"WorkItems": [
"★1. のﾌﾗｯﾄｹｰﾌﾞﾙを引き回し､基板に接続する"
],
"WorkPoints": [
"突き当たりまで押し込んでﾛｯｸする(ｺﾈｸﾀｰに対して傾きが無い事)",
"接続後､青ﾏｰｷﾝｸﾞ",
"ﾌﾚｰﾑ下側を通す",
"一度折り曲げた箇所は開かないこと",
"細いﾌﾗｯﾄｹｰﾌﾞﾙに重ならないように折り曲げる",
"端子面を下... | {
"QualityItem": "負荷確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｹｰﾌﾞﾙに負荷がかかって無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "静電対策工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "引き込みﾓｰﾀｰ取付け",
"WorkItems": [
"★1. の引き込みﾓｰﾀｰのﾌﾗｯﾄｹｰﾌﾞﾙを引き回し､基板に接続する"
],
"WorkPoints": [
"ﾌﾚｰﾑの裏側を通す",
"干渉注意",
"基盤の端面･ｺﾈｸﾀと平行になっている事",
"ﾌﾗｯﾄｹｰﾌﾞﾙ細･太･ﾓｰﾀｰ用3本が同時に重なっていないか確認する"
],
"Tolks": [],
"InspectionNo":... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "静電対策工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "引き込みﾓｰﾀｰ取付け",
"WorkItems": [
"★1. の引き込みﾓｰﾀｰのﾌﾗｯﾄｹｰﾌﾞﾙを引き回し､基板に接続する"
],
"WorkPoints": [
"ﾌﾚｰﾑの裏側を通す",
"干渉注意",
"基盤の端面･ｺﾈｸﾀと平行になっている事",
"ﾌﾗｯﾄｹｰﾌﾞﾙ細･太･ﾓｰﾀｰ用3本が同時に重なっていないか確認する"
],
"Tolks": [],
"InspectionNo":... | {
"QualityItem": "負荷確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｹｰﾌﾞﾙに負荷がかかって無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "静電対策工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "2.5㎜",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ規正ｶﾞｲﾄﾞ取付け",
"WorkItems": [
"1. に を挟みながら を取付ける(共締め)"
],
"WorkPoints": [
"固定時に が浮かない様注意(幅検査でNGになる)",
"2.5mmのﾌﾞﾛｯｸｹﾞｰｼﾞを挟んでﾎﾞﾙﾄを締めてきつくなったところでﾅｯﾄを締結",
"ﾅｯﾄ締結時､ のｸｯｼｮﾝ部をつぶさないように締め付けること",
"ﾅｯﾄの図のように 側... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:2.5㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "5㎜",
"ToolOther": "50cN･m",
"WorkName": "ﾃｰﾌﾟ規正ｶﾞｲﾄﾞ取付け",
"WorkItems": [
"1. に を挟みながら を取付ける(共締め)"
],
"WorkPoints": [
"固定時に が浮かない様注意(幅検査でNGになる)",
"2.5mmのﾌﾞﾛｯｸｹﾞｰｼﾞを挟んでﾎﾞﾙﾄを締めてきつくなったところでﾅｯﾄを締結",
"ﾅｯﾄ締結時､ のｸｯｼｮﾝ部をつぶさないように締め付けること",
"ﾅｯﾄの図のように ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN・m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "M2ﾅｯﾄ用特殊ｽﾊﾟﾅ(幅5厚さ2)",
"Size": "5㎜",
"ToolOther": "FM-4416",
"WorkName": "ﾃｰﾌﾟ規正ｶﾞｲﾄﾞ取付け",
"WorkItems": [
"1. に を挟みながら を取付ける(共締め)"
],
"WorkPoints": [
"固定時に が浮かない様注意(幅検査でNGになる)",
"2.5mmのﾌﾞﾛｯｸｹﾞｰｼﾞを挟んでﾎﾞﾙﾄを締めてきつくなったところでﾅｯﾄを締結",
"ﾅｯﾄ締結時､ のｸｯｼｮﾝ部をつぶさないように締め付けること",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "FM-4416",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "50cN・m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ規正ｶﾞｲﾄﾞ取付け",
"WorkItems": [
"1. に を挟みながら を取付ける(共締め)"
],
"WorkPoints": [
"固定時に が浮かない様注意(幅検査でNGになる)",
"2.5mmのﾌﾞﾛｯｸｹﾞｰｼﾞを挟んでﾎﾞﾙﾄを締めてきつくなったところでﾅｯﾄを締結",
"ﾅｯﾄ締結時､ のｸｯｼｮﾝ部をつぶさないように締め付けること",
"ﾅｯﾄの図のように 側にすること"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "\u002BNo.2",
"ToolOther": "60cN･m",
"WorkName": "側面ｶﾊﾞｰ取付け",
"WorkItems": [
"1. にSLIDER UNIT を入れた状態でCOVER をSCREW で取付ける"
],
"WorkPoints": [
"ﾌﾗｯﾄｹｰﾌﾞﾙ部",
"ﾒｲﾝﾓｰﾀｹｰﾌﾞﾙ",
"束線",
"引き込みﾓｰﾀｹｰﾌﾞﾙ･ﾌﾗｯﾄｹｰﾌﾞﾙ",
"先端部から順番に締め込む事",
"配線の挟み込み無... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "側面ｶﾊﾞｰ取付け",
"WorkItems": [
"1. にSLIDER UNIT を入れた状態でCOVER をSCREW で取付ける"
],
"WorkPoints": [
"ﾌﾗｯﾄｹｰﾌﾞﾙ部",
"ﾒｲﾝﾓｰﾀｹｰﾌﾞﾙ",
"束線",
"引き込みﾓｰﾀｹｰﾌﾞﾙ･ﾌﾗｯﾄｹｰﾌﾞﾙ",
"先端部から順番に締め込む事",
"配線の挟み込み無き事",
" の穴にSLIDER UNI... | {
"QualityItem": "負荷確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｹｰﾌﾞﾙに負荷がかかって無い事",
"Method": "目視",
"RecordMethod": "WDKC-G09-001",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "側面ｶﾊﾞｰ取付け",
"WorkItems": [
"1. にSLIDER UNIT を入れた状態でCOVER をSCREW で取付ける"
],
"WorkPoints": [
"ﾌﾗｯﾄｹｰﾌﾞﾙ部",
"ﾒｲﾝﾓｰﾀｹｰﾌﾞﾙ",
"束線",
"引き込みﾓｰﾀｹｰﾌﾞﾙ･ﾌﾗｯﾄｹｰﾌﾞﾙ",
"先端部から順番に締め込む事",
"配線の挟み込み無き事",
" の穴にSLIDER UNI... | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "噛み込み無い事",
"Method": "目視",
"RecordMethod": "WDKC-G09-001",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "側面ｶﾊﾞｰ取付け",
"WorkItems": [
"1. にSLIDER UNIT を入れた状態でCOVER をSCREW で取付ける"
],
"WorkPoints": [
"ﾌﾗｯﾄｹｰﾌﾞﾙ部",
"ﾒｲﾝﾓｰﾀｹｰﾌﾞﾙ",
"束線",
"引き込みﾓｰﾀｹｰﾌﾞﾙ･ﾌﾗｯﾄｹｰﾌﾞﾙ",
"先端部から順番に締め込む事",
"配線の挟み込み無き事",
" の穴にSLIDER UNI... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WDKC-G09-001",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "60cN･m",
"WorkName": "ｶﾊﾞｰ取付け1",
"WorkItems": [
"1. にCOVER PLATE をSCREW で取付け､ﾓｰﾀをSCREW で取付ける"
],
"WorkPoints": [
"SCREW とSCREW の長さの違いに注意",
"M3×6 白",
"M3×5 黒",
"COVER は重なっていてもわかりづらいので注意のこと",
"配線の噛み込み注意"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾊﾞｰ取付け1",
"WorkItems": [
"1. にCOVER PLATE をSCREW で取付け､ﾓｰﾀをSCREW で取付ける"
],
"WorkPoints": [
"SCREW とSCREW の長さの違いに注意",
"M3×6 白",
"M3×5 黒",
"COVER は重なっていてもわかりづらいので注意のこと",
"配線の噛み込み注意"
],
"Tolks": [
"締... | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "噛み込み無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾊﾞｰ取付け1",
"WorkItems": [
"1. にCOVER PLATE をSCREW で取付け､ﾓｰﾀをSCREW で取付ける"
],
"WorkPoints": [
"SCREW とSCREW の長さの違いに注意",
"M3×6 白",
"M3×5 黒",
"COVER は重なっていてもわかりづらいので注意のこと",
"配線の噛み込み注意"
],
"Tolks": [
"締... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｱﾘﾝｸﾞ部組立",
"WorkItems": [
"1. BLOCK の上面に油砥石をかける",
"2. BLOCK にCAM-FOLLOWER を通しWASHER WASHER の順で入れNUT で固定する"
],
"WorkPoints": [
"2個作製する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｱﾘﾝｸﾞ部組立",
"WorkItems": [
"1. BLOCK の上面に油砥石をかける",
"2. BLOCK にCAM-FOLLOWER を通しWASHER WASHER の順で入れNUT で固定する"
],
"WorkPoints": [
"2個作製する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cNm±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "右ﾚﾊﾞｰ部組立",
"WorkItems": [
"2. LEVER にBOLT NUT を取付ける",
"1. LEVER の表裏面の斜線穴の周辺にｱﾙｶﾝｻｽをかける"
],
"WorkPoints": [
"出代:9㎜",
"表裏面"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:9㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "100cN･m",
"WorkName": "右ﾚﾊﾞｰ部組立",
"WorkItems": [
"2. LEVER にBOLT NUT を取付ける",
"1. LEVER の表裏面の斜線穴の周辺にｱﾙｶﾝｻｽをかける"
],
"WorkPoints": [
"出代:9㎜",
"表裏面"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"Inspec... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "左ﾚﾊﾞｰ部組立",
"WorkItems": [
"1. LEVER の表裏面に油砥石をかける",
"2. LEVER にBOLT NUT を取付ける"
],
"WorkPoints": [
"表裏面",
"出代:9㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"9㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:9㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "左ﾚﾊﾞｰ部組立",
"WorkItems": [
"1. LEVER の表裏面に油砥石をかける",
"2. LEVER にBOLT NUT を取付ける"
],
"WorkPoints": [
"表裏面",
"出代:9㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"9㎜"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾞﾘｰｽ塗布",
"WorkItems": [
"◆1. にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"裏面",
"表面",
"穴の内側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1",
"◆作業者安全作業",
"※表裏面の... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左右ﾚﾊﾞｰ部組立",
"WorkItems": [
"1. にCOLLAR をはめて､PIN BRACKET を締付けNUT で固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "左右ﾚﾊﾞｰ部組立",
"WorkItems": [
"1. にCOLLAR をはめて､PIN BRACKET を締付けNUT で固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5Nm±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾌﾟﾚｰﾄﾛｰﾗｰ位置決め治具",
"Size": "",
"ToolOther": "FM-4675",
"WorkName": "ﾌﾞﾛｯｸ取付け",
"WorkItems": [
"1. BLOCK にｱﾙｶﾝｻｽをかける",
"2. PLATE にBLOCK ､ (2個)をBOLT (6個)で取付ける"
],
"WorkPoints": [
"矢印方向に押し当てて取付ける",
"検査書の規格値は参考",
"取付後、㉛を使用し通らないこと",
"矢印方向に押し当てて取付ける"
],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "FM-4675",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "検査書通りのこと",
"Method": "目視",
"RecordMethod": "WEBS-F013-010",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｯｸ取付け",
"WorkItems": [],
"WorkPoints": [
"矢印方向に押し当てて取付ける",
"検査書の規格値は参考",
"取付後、㉛を使用し通らないこと",
"矢印方向に押し当てて取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 2.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.02㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "2.5N･m",
"WorkName": "ﾌﾞﾛｯｸ取付け",
"WorkItems": [],
"WorkPoints": [
"矢印方向に押し当てて取付ける",
"検査書の規格値は参考",
"取付後、㉛を使用し通らないこと",
"矢印方向に押し当てて取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 2.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "2.5N･m",
"WorkName": "ﾌﾞﾛｯｸ位置調整",
"WorkItems": [],
"WorkPoints": [
"㉙ピン2箇所の取付けて固定"
],
"Tolks": [
"締付ﾄﾙｸ 2.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾌﾟﾚｰﾄﾛｰﾗｰ位置決め治具",
"Size": "",
"ToolOther": "FM-4675",
"WorkName": "ﾌﾞﾛｯｸ位置調整",
"WorkItems": [
"2. にBLOCK をBOLT (2個)で取付ける",
"1. BLOCK にｱﾙｶﾝｻｽをかける"
],
"WorkPoints": [
"㉙ピン2箇所の取付けて固定"
],
"Tolks": [
"締付ﾄﾙｸ 2.5N･m"
],
"InspectionNo": "",
"InspectionI... | {
"QualityItem": "寸法確認",
"ToolManageNo": "FM-4675",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｯｸ位置調整",
"WorkItems": [
"2. にBLOCK をBOLT (2個)で取付ける",
"1. BLOCK にｱﾙｶﾝｻｽをかける"
],
"WorkPoints": [
"㉙ピン2箇所の取付けて固定"
],
"Tolks": [
"締付ﾄﾙｸ 2.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "1㎜",
"ToolOther": "",
"WorkName": "左右ﾚﾊﾞｰ取付け",
"WorkItems": [
"2. 左右 の位置を合わせて固定する"
],
"WorkPoints": [
"広がった と の隙間にﾌﾞﾛｯｸｹﾞｰｼﾞ1㎜を挟みﾎﾞﾙﾄを締める",
" の先端と の干渉が無いことを確認したらﾄﾙｸﾄﾞﾗｲﾊﾞｰで締結する"
],
"Tolks": [
"締付ﾄﾙｸ 2.5N･m"
],
"InspectionNo": "",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間1.0㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "左右ﾚﾊﾞｰ取付け",
"WorkItems": [
"1. に をBOLT (4個)で取付ける",
"2. 左右 の位置を合わせて固定する"
],
"WorkPoints": [
"広がった と の隙間にﾌﾞﾛｯｸｹﾞｰｼﾞ1㎜を挟みﾎﾞﾙﾄを締める",
"若干､軽めに仮締めする",
" の先端と の干渉が無いことを確認したらﾄﾙｸﾄﾞﾗｲﾊﾞｰで締結する"
],
"Tolks": [
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼﾘｱﾙ銘板貼付",
"WorkItems": [
"1. の左ﾚﾊﾞｰ部に①を貼付ける"
],
"WorkPoints": [
"ｼﾘｱﾙｺｰﾄﾞAVD"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"25㎜",
"5㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法であること",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し1",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
"V±aK301",
"COM6a",
"±aK3010.09/10/11",
"101.02/03",
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"HDP",
"A1bK201",
"-VaT1022aF123",
... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し2",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"1aF121/2",
"\u002BV1/2aT101"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し3",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"1K301P",
"EX212",
"2bF125"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し4",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"AX212",
"2a/bF122",
"-VbT101"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words":... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し5",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"AX211",
"2a/bF121",
"-XV1/2aT101"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し6",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"A1K101T33K101",
"CX212",
"A2K101",
"A2aK201"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し7",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"BX211",
"1/3aK201"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し8",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"CX211",
"1/2/3/5_PWK601",
"2aK202"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し9",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"DX211",
"1/2/3/5_PWK602",
"4aK202"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し10",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"FX212",
"CN1K304",
"CN7K303"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words":... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し11",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"S001P",
"21aK201",
"T32K101",
"2aF125",
"BX212",
"1aF125"
],
"Tolks": [],
"InspectionNo... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し12",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"1S301P",
"*S201",
"DX212",
"T11/12K101",
"T21/22K101",
"6aK202",
"0.00/0.01"
],
"Tolk... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し13",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"CN1K603",
"2aF124",
"EX211"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": ... | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し14",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"T31K101",
"22aK202"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し15",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"5aK201"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し16",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"A1aK202",
"S24K101"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し17",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"A1aK201",
"S14K101"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し18",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"A2bK201",
"A2aK202"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し19",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"1aF123",
"\u002BVaT102"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引き回し20",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
":ｽﾀｰﾄ :ｺﾞｰﾙ",
"COM6b",
"COM7a"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "FMUﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6061",
"WorkName": "ﾊｰﾈｽ引結束",
"WorkItems": [
"1. 引き回したﾊｰﾈｽをｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定... | {
"QualityItem": "結束確認",
"ToolManageNo": "FM-6061",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｱﾘﾝｸﾞ部組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"BRACKET ",
"NUT WASHER WASHER ",
"CAM-FOLLOWER ",
"･締付けﾄﾙｸ:150cN･m",
"2.BRACKET にCAM-F... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｱﾘﾝｸﾞ部組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"BRACKET ",
"NUT WASHER WASHER ",
"CAM-FOLLOWER ",
"･締付けﾄﾙｸ:150cN･m",
"2.BRACKET ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cNm±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "150㎜",
"WorkName": "右ﾚﾊﾞｰ部組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"BOLT ",
"NUT ",
"出代9㎜",
"･締付けﾄﾙｸ : 100cN･m",
"2.LEVER にBOLT NUT を取付ける｡",
"･(注意... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:9㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "100cN･m",
"WorkName": "右ﾚﾊﾞｰ部組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"BOLT ",
"NUT ",
"出代9㎜",
"･締付けﾄﾙｸ : 100cN･m",
"2.LEVER にBOLT NUT を取付ける｡",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "150㎜",
"WorkName": "左ﾚﾊﾞｰ部組立",
"WorkItems": [],
"WorkPoints": [
"ｴｯｼﾞが立ってていないこと"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"BOLT ",
"NUT ",
"出代9㎜",
"2.LEVER にBOL... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:9㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "100cN･m",
"WorkName": "左ﾚﾊﾞｰ部組立",
"WorkItems": [],
"WorkPoints": [
"ｴｯｼﾞが立ってていないこと"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"BOLT ",
"NUT ",
"出代9㎜",
"2.L... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾞﾘｰｽ塗布",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左右ﾚﾊﾞｰ部組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"COLLAR ",
"NUT ",
"BRACKET ",
"PIN P001",
"COLLAR P004",
"NUT X593",
"M5ﾅｯﾄ",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "5N･m",
"WorkName": "左右ﾚﾊﾞｰ部組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"COLLAR ",
"NUT ",
"BRACKET ",
"PIN P001",
"COLLAR P004",
"NUT X593",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5Nm±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "BOLT取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"出代=2.5mm",
"割りの方向"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "BOLT取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"出代=2.5mm",
"割りの方向"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾌﾟﾚｰﾄﾛｰﾗｰ位置決め治具",
"Size": "",
"ToolOther": "FM-3253FM-4715",
"WorkName": "ﾌﾞﾛｯｸ取付け①",
"WorkItems": [
"3. PLATE に BRACKET を位置決め"
],
"WorkPoints": [
"取付後、下記赤線部の隙間確認㉖を使用し通らないこと",
"PLATE に㉕治具をセットし、斜めにならないように取付ける、取付後下記隙間確認の事",
"FM-4715(DXﾀｲﾌﾟ共用)でも使用可"
],
"Tolk... | {
"QualityItem": "寸法確認",
"ToolManageNo": "FM-3253FM-4715",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "検査書通りの事",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｯｸ取付け①",
"WorkItems": [
"3. PLATE に BRACKET を位置決め"
],
"WorkPoints": [
"取付後、下記赤線部の隙間確認㉖を使用し通らないこと",
"PLATE に㉕治具をセットし、斜めにならないように取付ける、取付後下記隙間確認の事",
"FM-4715(DXﾀｲﾌﾟ共用)でも使用可"
],
"Tolks": [],
"Inspe... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間0.02㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEBS-F013-011",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "2.5N･m",
"WorkName": "ﾌﾞﾛｯｸ取付け①",
"WorkItems": [
"3. PLATE に BRACKET を位置決め"
],
"WorkPoints": [
"取付後、下記赤線部の隙間確認㉖を使用し通らないこと",
"PLATE に㉕治具をセットし、斜めにならないように取付ける、取付後下記隙間確認の事",
"FM-4715(DXﾀｲﾌﾟ共用)でも使用可"
],
"Tolks": [],
"Insp... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾌﾟﾚｰﾄﾛｰﾗｰ位置決め治具",
"Size": "",
"ToolOther": "FM-3253FM-4715",
"WorkName": "ﾌﾞﾛｯｸ取付け②",
"WorkItems": [
"3､ に BRACKET を位置決め"
],
"WorkPoints": [
"取付後、隙間確認㉖を使用し通らないこと",
" に㉕治具をセットし、斜めにならないように取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "FM-3253FM-4715",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "検査書通りの事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｯｸ取付け②",
"WorkItems": [
"3､ に BRACKET を位置決め"
],
"WorkPoints": [
"取付後、隙間確認㉖を使用し通らないこと",
" に㉕治具をセットし、斜めにならないように取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"矢印側に角... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間0.02㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEBS-F013-011",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "2.5N･m",
"WorkName": "ﾌﾞﾛｯｸ取付け②",
"WorkItems": [
"3､ に BRACKET を位置決め"
],
"WorkPoints": [
"取付後、隙間確認㉖を使用し通らないこと",
" に㉕治具をセットし、斜めにならないように取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "1.0㎜",
"ToolOther": "",
"WorkName": "左右ﾚﾊﾞｰ取付け",
"WorkItems": [
"4. ﾌﾟﾚｰﾄを表面にし左側のﾚﾊﾞｰに S/Nｼｰﾙを貼る｡",
"2. を左右へ広げて手前のﾋﾞｽ1ヶを軽く固定する"
],
"WorkPoints": [
"指でｶﾞﾀ分を軽く押し､ﾌﾟﾚｰﾄとｱｰﾑの干渉が無い事を確認できたらﾋﾞｽを増締めする｡(ﾚﾊﾞｰとﾌﾟﾚｰﾄの隙間確認)約1mmの隙間",
"広がったﾌﾟﾚｰﾄとｱｰﾑの隙間にﾌﾞ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間1.0㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "2.5N･m",
"WorkName": "左右ﾚﾊﾞｰ取付け",
"WorkItems": [
"4. ﾌﾟﾚｰﾄを表面にし左側のﾚﾊﾞｰに S/Nｼｰﾙを貼る｡",
"2. を左右へ広げて手前のﾋﾞｽ1ヶを軽く固定する"
],
"WorkPoints": [
"指でｶﾞﾀ分を軽く押し､ﾌﾟﾚｰﾄとｱｰﾑの干渉が無い事を確認できたらﾋﾞｽを増締めする｡(ﾚﾊﾞｰとﾌﾟﾚｰﾄの隙間確認)約1mmの隙間",
"広がったﾌﾟﾚｰﾄとｱｰﾑの隙間に... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "高さ平面度測定治具てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "-FM-5001",
"WorkName": "ﾌﾟﾚｰﾄ取付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"BOLT ",
"WASHER ",
"NUT ",
"5､平面度測定",
"※基板下受けﾌﾞﾛｯｸ(自動交換用)ｷｯﾄ検... | {
"QualityItem": "平面度",
"ToolManageNo": "-FM-5001",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "-0.18㎜~\u002B0.13㎜",
"Method": "高さ平面度測定治具てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEBS-F013-011",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ(0.1/0.3/0,5㎜))",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ取付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"BOLT ",
"WASHER ",
"NUT ",
"5､平面度測定",
"※基板下受けﾌﾞﾛｯｸ(自動交換用)ｷｯﾄ検査表:WD... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "通り0.1㎜止まり0.3㎜ﾎﾞﾙﾄ・ﾌﾟﾚｰﾄ間:0.5㎜以上",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ(0.1/0.3/0,5㎜)",
"RecordMethod": "WEBS-F013-011",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5㎜B0X",
"ToolOther": "90cN･m",
"WorkName": "ﾌﾟﾚｰﾄ取付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"3､ へ2枚目のPLATE をBOLT とWASHER NUT で中央内側から取付ける",
"ﾋﾞｽの取付は中央から両ｻｲﾄﾞへ向けて取付けること",
"･... | {
"QualityItem": "締結ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台砥石かけ",
"WorkItems": [
"1. FRAME に砥石をかけ､ﾊﾞﾘ等の除去､確認 (色付き囲み表示部分)",
"2. 砥石がけ後㉘で洗浄する"
],
"WorkPoints": [
"左右共",
"LMｶﾞｲﾄﾞ取付面",
"LMｶﾞｲﾄﾞ当て面",
"Yﾌﾚｰﾑ取付面､Y軸LMｶﾞｲﾄﾞ取付面及び当て面､ﾘﾆｱｽｹｰﾙ取付面にかける",
"D-Pinに注意する"
],
... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【WX専用】Y軸LMｶﾞｲﾄﾞ仮取付け",
"WorkItems": [
"1. LINEAR-WAY の下面・スライダー上面に㉖をかける",
"2. LINEAR-WAY の防錆油･ｸﾞﾘｰｽ･ｺﾞﾐの除去を行う",
"◆3. LINEAR-WAY を架台に搭載しBOLT で仮締めをする"
],
"WorkPoints": [
"LMｶﾞｲﾄﾞ下面",
"ｽﾗｲﾀﾞｰ上面",
"手袋着用し作業する事",
... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取扱",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸LMｶﾞｲﾄﾞ押え治具",
"Size": "",
"ToolOther": "FM-4598",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け",
"WorkItems": [],
"WorkPoints": [
"治具取付けｲﾒｰｼﾞ",
"取付用ﾎﾞﾙﾄ",
"㉗とLMガイドの間に㉘を挟み込む"
],
"Tolks": [
"締付ﾄﾙｸ 2.4N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4598",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸LMｶﾞｲﾄﾞ押え治ｼﾞｸﾞｽﾍﾟｰｻ",
"Size": "",
"ToolOther": "FM-5069",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け",
"WorkItems": [
"4. LMｶﾞｲﾄﾞと当て面に隙間が無いことを確認する",
"1. ㉗を取付用ボルトで架台に固定する",
"3. LMｶﾞｲﾄﾞに仮締めしてあるﾎﾞﾙﾄを本締付けする",
"2. ㉗の押し当て用ボルトを締付けてLMガイドに当付ける"
],
"WorkPoints": [
"治具取付けｲﾒｰｼﾞ",
... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5069",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "2.4N･m",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け",
"WorkItems": [
"1. ㉗を取付用ボルトで架台に固定する",
"3. LMｶﾞｲﾄﾞに仮締めしてあるﾎﾞﾙﾄを本締付けする",
"2. ㉗の押し当て用ボルトを締付けてLMガイドに当付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.4N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け",
"WorkItems": [],
"WorkPoints": [
"治具取付けｲﾒｰｼﾞ",
"取付用ﾎﾞﾙﾄ",
"㉗とLMガイドの間に㉘を挟み込む"
],
"Tolks": [
"締付ﾄﾙｸ 2.4N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "26.5N･m",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け",
"WorkItems": [
"1. ㉗を取付用ボルトで架台に固定する",
"3. LMｶﾞｲﾄﾞに仮締めしてあるﾎﾞﾙﾄを本締付けする",
"2. ㉗の押し当て用ボルトを締付けてLMガイドに当付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "Y軸LMｶﾞｲﾄﾞ本取付け",
"WorkItems": [
"4. LMｶﾞｲﾄﾞと当て面に隙間が無いことを確認する"
],
"WorkPoints": [
"0.03mmｹﾞｰｼﾞが入らないこと",
"隙間確認後､REAR作業者と入れ替わり増し締め確認を行う"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"W... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜ｹﾞｰｼﾞが入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C02",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "CPU_BOX固定ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"2. BRACKET をBOLT WASHER にて取付ける",
"1. BRACKET にｲﾝｼｭﾛｯｸを通す"
],
"WorkPoints": [
"上方向に押し当てて取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"Inspect... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "天板ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. 前準備完成品 をBOLT WASHER にて取付ける"
],
"WorkPoints": [
"4ヵ所取付け"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"FRONT"
]... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾗﾝｽ取付前準備",
"WorkItems": [
"◆2. ﾄﾗﾝｽ側取付穴に移載治具が入るように､連結ﾋﾟﾝの高さを合わせ挿入する",
"◆4. ﾄﾗﾝｽを上昇させ､ﾄﾗﾝｽ台車から治具ごと引き抜く",
"◆3. 連結ﾋﾟﾝ上段2本に抜け防止ﾌﾟﾚｰﾄを挿入する",
"■1. 付属の検査書とﾄﾗﾝｽのｼﾘｱﾙ№が同じか確認し検査表に№を記入する(付属の検査書は一旦保管)"
],
"WorkPoints": [
"ﾗﾁ... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D06",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾗﾝｽ取付前準備",
"WorkItems": [
"◆2. ﾄﾗﾝｽ側取付穴に移載治具が入るように､連結ﾋﾟﾝの高さを合わせ挿入する",
"◆4. ﾄﾗﾝｽを上昇させ､ﾄﾗﾝｽ台車から治具ごと引き抜く",
"◆3. 連結ﾋﾟﾝ上段2本に抜け防止ﾌﾟﾚｰﾄを挿入する",
"■1. 付属の検査書とﾄﾗﾝｽのｼﾘｱﾙ№が同じか確認し検査表に№を記入する(付属の検査書は一旦保管)"
],
"WorkPoints": [
"ﾗﾁ... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WEAV-G002-D06",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾗﾝｽ移載治具",
"Size": "",
"ToolOther": "FM-4451",
"WorkName": "ﾄﾗﾝｽ取付前準備",
"WorkItems": [
"◆2. ﾄﾗﾝｽ側取付穴に移載治具が入るように､連結ﾋﾟﾝの高さを合わせ挿入する",
"◆4. ﾄﾗﾝｽを上昇させ､ﾄﾗﾝｽ台車から治具ごと引き抜く",
"◆3. 連結ﾋﾟﾝ上段2本に抜け防止ﾌﾟﾚｰﾄを挿入する",
"■1. 付属の検査書とﾄﾗﾝｽのｼﾘｱﾙ№が同じか確認し検査表に№を記入する(付属の検査書は一旦保管)"
],
"WorkPoint... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4451",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取扱",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾗﾝｽ移載ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6059",
"WorkName": "ﾄﾗﾝｽ取付前準備",
"WorkItems": [
"◆2. ﾄﾗﾝｽ側取付穴に移載治具が入るように､連結ﾋﾟﾝの高さを合わせ挿入する",
"◆4. ﾄﾗﾝｽを上昇させ､ﾄﾗﾝｽ台車から治具ごと引き抜く",
"◆3. 連結ﾋﾟﾝ上段2本に抜け防止ﾌﾟﾚｰﾄを挿入する",
"■1. 付属の検査書とﾄﾗﾝｽのｼﾘｱﾙ№が同じか確認し検査表に№を記入する(付属の検査書は一旦保管)"
],
"WorkPoi... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-6059",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取扱",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾗﾝｽ移載治具",
"Size": "",
"ToolOther": "FM-4451",
"WorkName": "ﾄﾗﾝｽ取付け",
"WorkItems": [
"6. ｽﾗｲﾄﾞｼｰﾄを外す",
"7. ﾄﾗﾝｽをBOLT WASHER にて取付ける",
"◆3. ﾄﾗﾝｽ移載治具を奥まで入れ込む"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4451",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取扱",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾗﾝｽ移載ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6059",
"WorkName": "ﾄﾗﾝｽ取付け",
"WorkItems": [
"6. ｽﾗｲﾄﾞｼｰﾄを外す",
"7. ﾄﾗﾝｽをBOLT WASHER にて取付ける",
"◆3. ﾄﾗﾝｽ移載治具を奥まで入れ込む"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-6059",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取扱",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "ﾄﾗﾝｽ取付け",
"WorkItems": [
"6. ｽﾗｲﾄﾞｼｰﾄを外す",
"7. ﾄﾗﾝｽをBOLT WASHER にて取付ける",
"◆3. ﾄﾗﾝｽ移載治具を奥まで入れ込む"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾗﾝｽｽﾗｲﾄﾞｼｰﾄ",
"Size": "",
"ToolOther": "FM-4836",
"WorkName": "ﾄﾗﾝｽ取付け",
"WorkItems": [
"6. ｽﾗｲﾄﾞｼｰﾄを外す",
"7. ﾄﾗﾝｽをBOLT WASHER にて取付ける",
"◆3. ﾄﾗﾝｽ移載治具を奥まで入れ込む"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4836",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【WX専用】ﾊﾟﾜｰﾕﾆｯﾄｹｰﾌﾞﾙ引き回し①(OP:REAR_17連切替仕様、REAR_ﾄﾚｲ仕様あり)",
"WorkItems": [
"1. REAR側にﾄﾞﾗｲﾊﾞｰ･ﾄﾚｲ電源ｹｰﾌﾞﾙを送る"
],
"WorkPoints": [
"ｹｰﾌﾞﾙの配置",
"L1K504",
"L11K504",
"L11K503",
"TRAY.PR",
"この穴からREAR側へ送る",
"･... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【WX専用】ﾊﾟﾜｰﾕﾆｯﾄｹｰﾌﾞﾙ引き回し①(OP:REAR_17連切替仕様、REAR_ﾄﾚｲ仕様あり)",
"WorkItems": [
"1. REAR側にﾄﾞﾗｲﾊﾞｰ･ﾄﾚｲ電源ｹｰﾌﾞﾙを送る"
],
"WorkPoints": [
"ｹｰﾌﾞﾙの配置",
"L1K504",
"L11K504",
"L11K503",
"TRAY.PR",
"この穴からREAR側へ送る",
"･... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "8㎜ｿｹｯﾄ",
"ToolOther": "6.0N･m",
"WorkName": "配線固定用ﾎﾟｽﾄ取付",
"WorkItems": [
"1. ﾌﾞﾚｰｶｰｹｰﾌﾞﾙに付属のFT-11を架台に挿し込み固定する",
"2. 前準備完成品 を取付ける"
],
"WorkPoints": [
"ﾌﾞﾚｰｶｰ配線を先に引き回す(ﾄﾗﾝｽ･ｱｰｽ)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｶﾊﾞｰﾌﾞﾗｹｯﾄ･ﾒｲﾝｽｲｯﾁ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5260",
"WorkName": "ﾒｲﾝﾌﾞﾚｰｶｰ取付け",
"WorkItems": [
"3. ｹｰﾌﾞﾙに付属のFT-11を架台に挿し込み固定する",
"1. 位置決め治具㉙でメインブレーカーの前後方向を位置決めしBOLT WASHER で取付ける",
"2. 位置決め治具㉙を使用しメインブレーカーのSW位置を調整する"
],
"WorkPoints": [
"傾きのない様に取付けること",
... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5260",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾒｲﾝﾌﾞﾚｰｶｰ取付け",
"WorkItems": [
"3. ｹｰﾌﾞﾙに付属のFT-11を架台に挿し込み固定する"
],
"WorkPoints": [
"傾きのない様に取付けること",
"真直ぐ押し込む",
"ﾒｲﾝﾌﾞﾚｰｶｰ"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionI... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.