input stringclasses 1
value | instruction stringlengths 202 3.29k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜ﾛﾝｸﾞﾋﾞｯﾄ",
"ToolOther": "6.0N･m",
"WorkName": "安全SW部取付(切替仕様)",
"WorkItems": [
"1. 13連連結部に②をWASHER BOLT で取付",
"2. 1.完成品にCOVER をWASHER BOLT で取付",
"1. 13連連結部に②をWASHER BOLT で取付",
"2. 1.完成品にCOVER をWASHER BOLT で取付",
"3. 2.完成品に①をBOLT WASHER で取付"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "200cN･m",
"WorkName": "安全SW部取付(切替仕様)",
"WorkItems": [
"4. 3.完成品に③をBOLT WASHER で取付"
],
"WorkPoints": [
"切替仕様時作業",
"ｶﾊﾞｰを矢印方向にｽﾗｲﾄﾞさせ挿入する"
],
"Tolks": [
"締付ﾄﾙｸ 200cN･m"
],
"InspectionNo": "",
"InspectionItems":... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "200cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ﾃｰﾌﾟ浮き及び安全SW配線、引き回し(切替仕様)",
"WorkItems": [
"1. ﾃｰﾌﾟ浮き検出の配線を図の経路に引き回す"
],
"WorkPoints": [
"切替仕様時作業",
"13連ｶｯﾃｨﾝｸﾞﾊﾞﾙﾌﾞ下付近"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ浮き及び安全SW配線、引き回し(切替仕様)",
"WorkItems": [
"1. ﾃｰﾌﾟ浮き検出の配線を図の経路に引き回す"
],
"WorkPoints": [
"切替仕様時作業",
"13連ｶｯﾃｨﾝｸﾞﾊﾞﾙﾌﾞ下付近"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEBS-F013-103",
"Other": "切替仕様",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "ﾌｨｰﾀﾞｰ左側固定部取付(切替仕様)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"左側固定部"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰ左側固定部取付(切替仕様)",
"WorkItems": [
"1. 架台にBRACKET を②WASHER で取付SCREW を締結",
"3. 架台ﾎﾟｽﾄへ⑤をWASHER BOLT で取付",
"2. 架台に①をWASHER で取付"
],
"WorkPoints": [
"切替仕様時作業"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"In... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "350cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側ﾌｨｰﾀﾞｰ固定部配線(切替仕様)",
"WorkItems": [
"1. 本体に取付けたﾌｨﾀﾞｰ固定部の配線を引き回し結束",
"2. COVER をSCREW で取付",
"3. ﾄﾞﾛｱｺﾈｸﾀを取付"
],
"WorkPoints": [
"切替仕様時作業",
"ﾋﾟﾝとﾄﾞﾛｱの穴位置を合わせ締結",
"残りのM6ﾎﾞﾙﾄ2本は交換台車置台のBOXへ入れる"
],
"Tolks": ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEBS-F013-103",
"Other": "切替仕様",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN･m",
"WorkName": "左側ﾌｨｰﾀﾞｰ固定部配線(切替仕様)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "左側ﾌｨｰﾀﾞｰ固定部配線(切替仕様)",
"WorkItems": [
"3. ﾄﾞﾛｱｺﾈｸﾀを取付"
],
"WorkPoints": [
"ﾋﾟﾝとﾄﾞﾛｱの穴位置を合わせ締結",
"残りのM6ﾎﾞﾙﾄ2本は交換台車置台のBOXへ入れる"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "交換台車支持部取付(切替仕様)",
"WorkItems": [
"3. 架台にCOVER をSCREW WASHER で取付",
"2. ②を位置決めして取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 300cN･m",
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "交換台車支持部取付(切替仕様)",
"WorkItems": [
"1. 13連供給側へ①をBOLT で取付",
"3. 架台にCOVER をSCREW WASHER で取付",
"2. ②を位置決めして取付"
],
"WorkPoints": [
"指示する溝にﾋﾟﾝを合わせ､段付部に押し付けながら固定する"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m",
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.03㎜以内",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "切替仕様",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "交換台車支持部取付(切替仕様)",
"WorkItems": [
"3. 架台にCOVER をSCREW WASHER で取付",
"2. ②を位置決めして取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 300cN･m",
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN･m",
"WorkName": "交換台車支持部取付(切替仕様)",
"WorkItems": [
"3. 架台にCOVER をSCREW WASHER で取付",
"2. ②を位置決めして取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 300cN･m",
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "17連交換台車駆動部取付(切替仕様)",
"WorkItems": [
"1. 架台にPIN を圧入し､②をBOLT WASHER で取付",
"2. 1.完成品に①を取付"
],
"WorkPoints": [
"矢印方向に押し付けながら締結する",
"ﾋﾟﾝ出代 : 5㎜",
"先端部分を先に入れる",
"切替仕様時作業"
],
"Tolks": [],
"Ins... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "17連交換台車駆動部取付(切替仕様)",
"WorkItems": [
"1. 架台にPIN を圧入し､②をBOLT WASHER で取付",
"2. 1.完成品に①を取付"
],
"WorkPoints": [
"矢印方向に押し付けながら締結する",
"ﾋﾟﾝ出代 : 5㎜",
"先端部分を先に入れる",
"切替仕様時作業"
],
"Tolks": [],
"Ins... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "17連交換台車駆動部取付(切替仕様)",
"WorkItems": [
"1. 架台にPIN を圧入し､②をBOLT WASHER で取付",
"2. 1.完成品に①を取付"
],
"WorkPoints": [
"矢印方向に押し付けながら締結する",
"ﾋﾟﾝ出代 : 5㎜",
"先端部分を先に入れる",
"切替仕様時作業"
],
"Tolks": [],
"Inspection... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "17連交換台車駆動部取付(切替仕様)",
"WorkItems": [
"1. 架台にPIN を圧入し､②をBOLT WASHER で取付",
"2. 1.完成品に①を取付"
],
"WorkPoints": [
"矢印方向に押し付けながら締結する",
"ﾋﾟﾝ出代 : 5㎜",
"先端部分を先に入れる",
"切替仕様時作業"
],
"Tolks": [
"締付ﾄﾙｸ 40N･m",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEBS-F013-103",
"Other": "切替仕様",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "台車駆動部、配線配管接続(切替仕様)",
"WorkItems": [
"1. 17連交換台車駆動部の配線･配管を接続",
"2. ﾄﾚｲ使用時はCABLE を取付"
],
"WorkPoints": [
"黒ﾗｲﾝは手前側･白ﾗｲﾝは奥側に接続",
"配管の黒を接続ｼﾞｮｲﾝﾄΦ6",
"配管の白ﾗｲﾝ有を接続ｼﾞｮｲﾝﾄΦ8",
"切替仕様時作業"
],
"Tolks": [],
"Insp... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "切替仕様",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "台車位置決め基準平行出し治具",
"Size": "",
"ToolOther": "FM-3354",
"WorkName": "台車ｽﾄｯﾊﾟｰの平行調整(切替仕様)",
"WorkItems": [
"1. 交換台車対応ﾕﾆｯﾄの平行調整実施"
],
"WorkPoints": [
"平行度 :0.02mm以下",
"切替仕様時作業",
"駆動部側で測定しｽﾄｯﾊﾟﾎﾞﾙﾄを調整",
"ﾍｯﾄﾞﾌﾟﾚｰﾄに㉙と㉗を取付け、平行を調整確認する",
"平行度の調整は駆動部(左側)のｽﾄｯﾊﾟｰﾎﾞﾙﾄ... | {
"QualityItem": "設置確認",
"ToolManageNo": "FM-3354",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEBS-F013-103",
"Other": "切替仕様",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "台車ｽﾄｯﾊﾟｰの平行調整(切替仕様)",
"WorkItems": [
"1. 交換台車対応ﾕﾆｯﾄの平行調整実施"
],
"WorkPoints": [
"平行度 :0.02mm以下",
"切替仕様時作業",
"駆動部側で測定しｽﾄｯﾊﾟﾎﾞﾙﾄを調整",
"ﾍｯﾄﾞﾌﾟﾚｰﾄに㉙と㉗を取付け、平行を調整確認する",
"平行度の調整は駆動部(左側)のｽﾄｯﾊﾟｰﾎﾞﾙﾄにて調... | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.02㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEBS-F013-103",
"Other": "切替仕様",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞ部ﾏｸﾞﾈｯﾄｽﾀﾝﾄﾞ取付治具",
"Size": "",
"ToolOther": "FM-2898",
"WorkName": "台車ｽﾄｯﾊﾟｰの平行調整(切替仕様)",
"WorkItems": [
"1. 交換台車対応ﾕﾆｯﾄの平行調整実施"
],
"WorkPoints": [
"平行度 :0.02mm以下",
"切替仕様時作業",
"駆動部側で測定しｽﾄｯﾊﾟﾎﾞﾙﾄを調整",
"ﾍｯﾄﾞﾌﾟﾚｰﾄに㉙と㉗を取付け、平行を調整確認する",
"平行度の調整は駆動部(左側)のｽﾄｯﾊ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2898",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEBS-F013-103",
"Other": "切替仕様",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "200cN･m",
"WorkName": "ﾌｨｰﾀﾞｰ右側固定部取付(切替仕様)",
"WorkItems": [
"1. 13連供給部に①をBOLT WASHER ､BOLT WASHER で取付､BRACKET をBOLT WASHER で取付しBRACKET に⑥を取付",
"2. 左側駆動部と右側支持部間の寸法を確認"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "200cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾌｨｰﾀﾞｰ右側固定部取付(切替仕様)",
"WorkItems": [
"1. 13連供給部に①をBOLT WASHER ､BOLT WASHER で取付､BRACKET をBOLT WASHER で取付しBRACKET に⑥を取付",
"2. 左側駆動部と右側支持部間の寸法を確認"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 200... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰ右側固定部取付(切替仕様)",
"WorkItems": [
"2. 左側駆動部と右側支持部間の寸法を確認"
],
"WorkPoints": [
"A寸法が規格外の場合､赤丸部を緩め再調整する",
"※A寸法が規格外の場合､交換台車駆動部のｶﾞｲﾄﾞ部を再調整する",
"台車駆動部ｶﾞｲﾄﾞ位置出し治具に当付け固定する"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:408±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "WEBS-F013-103",
"Other": "切替仕様",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "台車駆動部ｶﾞｲﾄﾞ位置出し治具",
"Size": "",
"ToolOther": "FM-4625",
"WorkName": "ﾌｨｰﾀﾞｰ右側固定部取付(切替仕様)",
"WorkItems": [
"2. 左側駆動部と右側支持部間の寸法を確認"
],
"WorkPoints": [
"A寸法が規格外の場合､赤丸部を緩め再調整する",
"※A寸法が規格外の場合､交換台車駆動部のｶﾞｲﾄﾞ部を再調整する",
"台車駆動部ｶﾞｲﾄﾞ位置出し治具に当付け固定する"
],
"Tolks": [
"締... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4625",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "切替仕様",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.9N･m",
"WorkName": "ﾌｨｰﾀﾞｰ右側固定部取付(切替仕様)",
"WorkItems": [
"2. 左側駆動部と右側支持部間の寸法を確認"
],
"WorkPoints": [
"A寸法が規格外の場合､赤丸部を緩め再調整する",
"※A寸法が規格外の場合､交換台車駆動部のｶﾞｲﾄﾞ部を再調整する",
"台車駆動部ｶﾞｲﾄﾞ位置出し治具に当付け固定する"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.9N・m±10%3.6N・m±10%5.3N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "架台へｶﾊﾞｰ取付(切替仕様)",
"WorkItems": [],
"WorkPoints": [
"切替仕様時作業",
"ｷｰが挿入できるか確認する",
"①ｶﾊﾞｰは台車使用時のみ取付",
"ﾄﾞﾛｱ取付部の架台の切り欠き部より100㎜"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionIt... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "200cN･m",
"WorkName": "架台へｶﾊﾞｰ取付(切替仕様)",
"WorkItems": [
"2. 架台に①を取付､架台側にLABEL を貼付ける",
"1. ｶﾊﾞｰをBOLT WASHER で固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 200cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Word... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "200cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "架台へｶﾊﾞｰ取付(切替仕様)",
"WorkItems": [],
"WorkPoints": [
"切替仕様時作業",
"ｷｰが挿入できるか確認する",
"①ｶﾊﾞｰは台車使用時のみ取付",
"ﾄﾞﾛｱ取付部の架台の切り欠き部より100㎜"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "200cN･m",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(切替仕様)",
"WorkItems": [
"1. 本体へ①を取付",
"2. 取付け後､上下･前後の位置調整を行う",
"1. 本体へ①を取付",
"2. 取付け後､上下･前後の位置調整を行う"
],
"WorkPoints": [
"このﾎﾞﾙﾄを締付けて取付ける",
"調整の際13連ﾌｨｰﾀﾞｰｶﾊﾞｰのﾗｲﾝと合わせる事",
"手前... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "200cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(切替仕様)",
"WorkItems": [
"1. 本体へ①を取付",
"2. 取付け後､上下･前後の位置調整を行う"
],
"WorkPoints": [
"このﾎﾞﾙﾄを締付けて取付ける",
"調整の際13連ﾌｨｰﾀﾞｰｶﾊﾞｰのﾗｲﾝと合わせる事",
"手前と奥側を上下合わせる",
"赤丸部分を緩め､前後､上下位置を調整"
],
"Tolks": [
"締付... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "切替仕様",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "T-20",
"ToolOther": "200cN･m",
"WorkName": "ｷｰｽｲｯﾁの調整(切替仕様)",
"WorkItems": [
"■1. ｷｰｽｲｯﾁ挿入時の調整と確認を行う",
"■2. ｽｲｯﾁ本体の取付ﾎﾞﾙﾄを規定ﾄﾙｸにて締結",
"3. ｷｰSWの上にCOVER をSCREW で取付"
],
"WorkPoints": [
"(2)ｱｸﾁｭｴｰﾀの位置調整･ｶﾊﾞｰを閉じる時に挿入されるｷｰがｽｲｯﾁの 中心に来る様に調整し確認･ｷｰが入ると... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "200cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "安全ｷｰSW調整治具",
"Size": "",
"ToolOther": "FM-3115",
"WorkName": "ｷｰｽｲｯﾁの調整(切替仕様)",
"WorkItems": [
"■1. ｷｰｽｲｯﾁ挿入時の調整と確認を行う",
"■2. ｽｲｯﾁ本体の取付ﾎﾞﾙﾄを規定ﾄﾙｸにて締結",
"3. ｷｰSWの上にCOVER をSCREW で取付"
],
"WorkPoints": [
"(2)ｱｸﾁｭｴｰﾀの位置調整･ｶﾊﾞｰを閉じる時に挿入されるｷｰがｽｲｯﾁの 中心に来る様に調整し確認･ｷｰが入るときと入り... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3115",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに取付出来ている事",
"Method": "目視",
"RecordMethod": "WEBS-F013-103",
"Other": "切替仕様",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｷｰｽｲｯﾁの調整(切替仕様)",
"WorkItems": [
"■1. ｷｰｽｲｯﾁ挿入時の調整と確認を行う"
],
"WorkPoints": [
"(2)ｱｸﾁｭｴｰﾀの位置調整･ｶﾊﾞｰを閉じる時に挿入されるｷｰがｽｲｯﾁの 中心に来る様に調整し確認･ｷｰが入るときと入りきった時両方で干渉無い事を確認",
"切替仕様時作業",
"（1）スイッチとアクチュエータの隙間調整カバーが閉じた\u3000\u3000状... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.8~2.1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "T-20",
"ToolOther": "200cN･m",
"WorkName": "ｷｰｽｲｯﾁの調整(切替仕様)",
"WorkItems": [
"■1. ｷｰｽｲｯﾁ挿入時の調整と確認を行う",
"■2. ｽｲｯﾁ本体の取付ﾎﾞﾙﾄを規定ﾄﾙｸにて締結",
"3. ｷｰSWの上にCOVER をSCREW で取付"
],
"WorkPoints": [
"(2)ｱｸﾁｭｴｰﾀの位置調整･ｶﾊﾞｰを閉じる時に挿入されるｷｰがｽｲｯﾁの 中心に来る様に調整し確認･ｷｰが入ると... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ｶﾊﾞｰ(P621)の取付(切替仕様)",
"WorkItems": [
"1. 13連供給部にCOVER をBOLT WASHER で取付"
],
"WorkPoints": [
"切替仕様時作業"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ連結部組立治具(本体側)",
"Size": "",
"ToolOther": "FM-2901",
"WorkName": "ﾄﾚｲ位置決めﾌﾞﾛｯｸ取付(切替仕様)",
"WorkItems": [
"1. 架台にBLOCK をBOLT WASHER で取付(仮固定)",
"2. 架台に②をBOLT WASHER で取付(仮固定)",
"5. ㉘を取外す",
"3. 架台に㉘を取付",
"4. ㉘にBLOCK ②を当てつけ再度、締付ける"
],
"WorkPoints": [
"赤丸... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2901",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "切替仕様",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "26.5N･m",
"WorkName": "ﾄﾚｲ位置決めﾌﾞﾛｯｸ取付(切替仕様)",
"WorkItems": [
"5. ㉘を取外す",
"4. ㉘にBLOCK ②を当てつけ再度、締付ける"
],
"WorkPoints": [
"BLOCK ②共､隙間なく取付",
"矢印方向に当てつけ",
"切替仕様時作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIt... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ延長取付(切替仕様)",
"WorkItems": [
"1. M6､2本を外しﾄﾞﾛｱｺﾈｸﾀ延長部を取付"
],
"WorkPoints": [
"切替仕様時作業"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"M6",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "開閉ｶﾊﾞｰ調整①",
"WorkItems": [
"開閉ｶﾊﾞｰと天井ｶﾊﾞｰの隙間確認",
"開閉ｶﾊﾞｰと側面ｶﾊﾞｰの段差確認",
"2. 床から開閉ｶﾊﾞｰ開放時の高さ調整",
"■1. 開閉ｶﾊﾞｰを固定している2×2-M6､4本を緩め左右の隙間調整",
"3. 開閉ｶﾊﾞｰを閉めた時､ﾌｨｰﾀﾞｰｶﾊﾞｰとの隙間確認"
],
"WorkPoints": [
"ｶﾊﾞｰ開閉... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ調整①",
"WorkItems": [
"開閉ｶﾊﾞｰと天井ｶﾊﾞｰの隙間確認",
"開閉ｶﾊﾞｰと側面ｶﾊﾞｰの段差確認",
"2. 床から開閉ｶﾊﾞｰ開放時の高さ調整",
"■1. 開閉ｶﾊﾞｰを固定している2×2-M6､4本を緩め左右の隙間調整"
],
"WorkPoints": [
"ｶﾊﾞｰ開閉時､天井ｶﾊﾞｰと隙間があること",
"隙間:7.5㎜以下",
"隙間:... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:7.5㎜以下",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ調整①",
"WorkItems": [
"3. 開閉ｶﾊﾞｰを閉めた時､ﾌｨｰﾀﾞｰｶﾊﾞｰとの隙間確認"
],
"WorkPoints": [
"開閉ｶﾊﾞｰが側面ｶﾊﾞｰより外にでないこと",
"左右のｶﾞｽﾀﾞﾝﾊﾟｰ取付けﾎﾞﾙﾄ､2×2-M6を緩め調整する",
"規格値:①\u002B(②-94)=1710±5mm"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "1710±5㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "WEBS-F013-101",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ調整②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾎﾞﾙﾄ取付箇所",
"前側",
"後側",
"左側",
"右側",
"現在の作業位置",
"面より出ないこと"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:3~5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ安全ｽｲｯﾁの調整",
"WorkItems": [
"1. 安全ｽｲｯﾁのﾚﾊﾞｰ干渉確認",
"2. 安全ｽｲｯﾁのﾚﾊﾞｰ､遊び確認"
],
"WorkPoints": [
"調整は2-M5を緩め､ｽｲｯﾁ本体を動かし調整する",
"上下に遊びがあること",
"開閉ｶﾊﾞｰの開放時･未開放時､安全ｽｲｯﾁﾚﾊﾞｰが他面と干渉ないことを確認"
],
"Tolks": [
"締付ﾄﾙｸ ... | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｶﾊﾞｰ開閉時、干渉無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "開閉ｶﾊﾞｰ安全ｽｲｯﾁの調整",
"WorkItems": [
"1. 安全ｽｲｯﾁのﾚﾊﾞｰ干渉確認",
"2. 安全ｽｲｯﾁのﾚﾊﾞｰ､遊び確認"
],
"WorkPoints": [
"調整は2-M5を緩め､ｽｲｯﾁ本体を動かし調整する",
"上下に遊びがあること",
"開閉ｶﾊﾞｰの開放時･未開放時､安全ｽｲｯﾁﾚﾊﾞｰが他面と干渉ないことを確認"
],
"Tolks": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "開閉ｶﾊﾞｰ調整③",
"WorkItems": [
"■1. 安全ｽｲｯﾁの位置を調整する",
"■2. 安全ｽｲｯﾁとｱｸﾁｭｴｰﾀの隙間を調整する",
"■3. 安全ｽｲｯﾁとｱｸﾁｭｴｰﾀを調整する(前後･左右)",
"3. COVER をSPACER BOLT WASHER で取付"
],
"WorkPoints": [
"取付後､ｶﾊﾞｰと安全SWが干渉していないか確認する"
]... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "前面ｶﾊﾞｰ安全SWﾌﾞﾗｹｯﾄ位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5007",
"WorkName": "開閉ｶﾊﾞｰ調整③",
"WorkItems": [
"■1. 安全ｽｲｯﾁの位置を調整する",
"■2. 安全ｽｲｯﾁとｱｸﾁｭｴｰﾀの隙間を調整する",
"■3. 安全ｽｲｯﾁとｱｸﾁｭｴｰﾀを調整する(前後･左右)"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m"
],... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5007",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに取付出来ている事",
"Method": "前面ｶﾊﾞｰ安全SWﾌﾞﾗｹｯﾄ位置調整ｼﾞｸﾞ",
"RecordMethod": "WEBS-F013-101",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "開閉ｶﾊﾞｰ安全ｷｰSW調整治具",
"Size": "2.3㎜",
"ToolOther": "FM-3116",
"WorkName": "開閉ｶﾊﾞｰ調整③",
"WorkItems": [],
"WorkPoints": [
"規格値: A=4.7㎜±1㎜"
],
"Tolks": [
"締付ﾄﾙｸ 200cN･m",
"締付ﾄﾙｸ 200cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"前側",
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-3116",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:4.7±1㎜",
"Method": "開閉ｶﾊﾞｰ安全ｷｰSW調整治具",
"RecordMethod": "WEBS-F013-101",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "T-20",
"ToolOther": "200cN･m",
"WorkName": "開閉ｶﾊﾞｰ調整③",
"WorkItems": [],
"WorkPoints": [
"規格値: A=4.7㎜±1㎜",
"規格値: A=4.7㎜±1㎜"
],
"Tolks": [
"締付ﾄﾙｸ 200cN･m",
"締付ﾄﾙｸ 200cN･m",
"締付ﾄﾙｸ 200cN･m",
"締付ﾄﾙｸ 200cN･m"
],
"InspectionNo":... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "200cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "指詰め防止ｶﾊﾞｰ取付",
"WorkItems": [
"1. COVER をBOLT WASHER で取付"
],
"WorkPoints": [
"ｶﾊﾞｰが薄いため折り曲げに注意",
"やぐらと平行に取付のこと"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾍｯﾄﾞ取付",
"WorkItems": [
"1. ﾍｯﾄﾌﾟﾚ-ﾄに①②のいずれかをﾍｯﾄﾌﾟﾚｰﾄ付属ﾎﾞﾙﾄにて取付"
],
"WorkPoints": [
"ﾏｼﾝ仕様を確認し取付けること",
"右側上の付属ﾎﾞﾙﾄが長い為､最初にねじ込みを行うこと"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"Insp... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｷﾏ確認治具",
"Size": "5㎜",
"ToolOther": "FM-3224",
"WorkName": "後面左右下ｶﾊﾞｰ取付",
"WorkItems": [
"1. 上カバーとCOVER の間に㉖治具(5㎜)を挟みCOVER で固定",
"2. 上カバーとCOVER の間に㉖治具(5㎜)を挟みCOVER で固定"
],
"WorkPoints": [
"ﾒｲﾝｴｱｰ圧がｶﾊﾞｰ開口部の中央にあることを確認する",
"押し当て"
],
"Tolks": [
"締付ﾄﾙｸ 200cN... | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-3224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:5㎜",
"Method": "ｽｷﾏ確認治具",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "200cN･m",
"WorkName": "後面左右下ｶﾊﾞｰ取付",
"WorkItems": [
"1. 上カバーとCOVER の間に㉖治具(5㎜)を挟みCOVER で固定",
"2. 上カバーとCOVER の間に㉖治具(5㎜)を挟みCOVER で固定"
],
"WorkPoints": [
"ﾒｲﾝｴｱｰ圧がｶﾊﾞｰ開口部の中央にあることを確認する",
"押し当て"
],
"Tolks": [
"締付ﾄﾙｸ 20... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "200cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "ﾄﾚｲ連結ﾌﾟﾚｰﾄ取付(R)〔ﾄﾚｲﾌｨｰﾀﾞｰ対応、切替仕様〕",
"WorkItems": [
"1. 架台にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"架台寸法 架台端面~ﾌﾞﾗｹｯﾄ端面まで50㎜",
"ﾄﾚｲﾌｨｰﾀﾞ仕様､切替仕様時作業",
"下側より取付",
"切替仕様時も取付る事"
],
"Tolks": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾄﾚｲ連結ﾌﾟﾚｰﾄ取付(R)〔ﾄﾚｲﾌｨｰﾀﾞｰ対応、切替仕様〕",
"WorkItems": [
"1. 架台にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"架台寸法 架台端面~ﾌﾞﾗｹｯﾄ端面まで50㎜",
"ﾄﾚｲﾌｨｰﾀﾞ仕様､切替仕様時作業",
"下側より取付",
"切替仕様時も取付る事"
],
"Tolks": [
"締付ﾄﾙｸ... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:50㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾗｹｯﾄ位置決め治具",
"Size": "",
"ToolOther": "FM-3310",
"WorkName": "ﾄﾚｲ連結ﾌﾟﾚｰﾄ取付(R)〔ﾄﾚｲﾌｨｰﾀﾞｰ対応、切替仕様〕",
"WorkItems": [
"1. 架台にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"架台寸法 架台端面~ﾌﾞﾗｹｯﾄ端面まで50㎜",
"ﾄﾚｲﾌｨｰﾀﾞ仕様､切替仕様時作業",
"下側より取付",
"切替仕様時も取付る事"
],
"Tolks": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3310",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付られている事",
"Method": "ﾌﾞﾗｹｯﾄ位置決め治具",
"RecordMethod": "-",
"Other": "ﾄﾚｲ仕様切替仕様",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｷﾏ確認治具",
"Size": "5㎜",
"ToolOther": "FM-3224",
"WorkName": "左側面下側ｶﾊﾞｰ取付",
"WorkItems": [
"1. COVER をSCREW で仮付",
"2. COVER ･COVER をSCREW で仮付",
"3. 調整･締付け"
],
"WorkPoints": [
"中央に仮取付け",
"中央に仮付",
"高さを中央ｶﾊﾞｰに合わせる(隙間5㎜)",
"両端の隙間を均等に締付け",
"ｶﾊﾞｰの高さを... | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-3224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:5㎜",
"Method": "ｽｷﾏ確認治具",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "360cN･m",
"WorkName": "左側面下側ｶﾊﾞｰ取付",
"WorkItems": [
"3. 調整･締付け"
],
"WorkPoints": [
"両端の隙間を均等に締付け",
"ｶﾊﾞｰの高さを合わせる (ｶﾊﾞｰ間隙間:5㎜)",
"COVER とCOVER COVER の隙間を1~2㎜開けること"
],
"Tolks": [
"締付ﾄﾙｸ 360cN･m"
],
"Inspec... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "350cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "左側面下側ｶﾊﾞｰ取付",
"WorkItems": [
"3. 調整･締付け"
],
"WorkPoints": [
"両端の隙間を均等に締付け",
"ｶﾊﾞｰの高さを合わせる (ｶﾊﾞｰ間隙間:5㎜)",
"COVER とCOVER COVER の隙間を1~2㎜開けること"
],
"Tolks": [
"締付ﾄﾙｸ 360cN･m"
],
"InspectionNo": "",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "1~2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "左側延長ｺﾝﾍﾞｱｶﾊﾞｰ取付",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱについているPCｶﾊﾞｰを取外す",
"2. 延長ｺﾝﾍﾞｱ 上側を本体にBOLT WASHER で取付",
"3. 延長ｺﾝﾍﾞｱ 下側を本体にWASHER BOLT で取付",
"1. 延長ｺﾝﾍﾞｱについているPCｶﾊﾞｰを取外す",
"2. 延長ｺﾝﾍﾞｱ 上側を本体にBOLT WASHER で取付",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "左側延長ｺﾝﾍﾞｱｶﾊﾞｰ取付",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱについているPCｶﾊﾞｰを取外す",
"2. 延長ｺﾝﾍﾞｱ 上側を本体にBOLT WASHER で取付",
"3. 延長ｺﾝﾍﾞｱ 下側を本体にWASHER BOLT で取付",
"1. 延長ｺﾝﾍﾞｱについているPCｶﾊﾞｰを取外す",
"2. 延長ｺﾝﾍﾞｱ 上側を本体にBOLT WASHER で取付",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "左側延長ｺﾝﾍﾞｱｶﾊﾞｰ取付",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱについているPCｶﾊﾞｰを取外す",
"2. 延長ｺﾝﾍﾞｱ 上側を本体にBOLT WASHER で取付",
"3. 延長ｺﾝﾍﾞｱ 下側を本体にWASHER BOLT で取付"
],
"WorkPoints": [
"配線終了後にPCｶﾊﾞｰを再度取付",
"参考値:ﾚｰﾙとｶﾊﾞｰの隙間7㎜",
"ﾚｰﾙ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側延長ｺﾝﾍﾞｱ配線①",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱのP板検出の配線を接続しｲﾝｼｭﾛｯｸで固定"
],
"WorkPoints": [
"ｺﾈｸﾀ名称 (左側)B11370R･B1135R",
"配線に負荷がかからない様､注意",
"ﾋﾟﾝの破損､抜けの確認をする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEBS-F013-103",
"Other": "延長ｺﾝﾍﾞｱ仕様",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側延長ｺﾝﾍﾞｱ配線②",
"WorkItems": [
"1. ①にCABLE-SUPPORT BOLT を取付",
"2. 延長ｺﾝﾍﾞｱ配線を引き回し結束",
"3. COVER をSCREW で取付",
"4. 外したPCｶﾊﾞｰ取付"
],
"WorkPoints": [
"M6ﾄﾗｽﾎﾞﾙﾄ取外し",
"ｺﾈｸﾀCNEXRを接続",
"ｸﾗﾝﾌﾟに配線取付",
"取外したPCｶﾊ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "延長ｺﾝﾍﾞｱ仕様",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "左側延長ｺﾝﾍﾞｱ配線②",
"WorkItems": [
"3. COVER をSCREW で取付",
"4. 外したPCｶﾊﾞｰ取付"
],
"WorkPoints": [
"取外したPCｶﾊﾞｰを取付"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "左側延長ｺﾝﾍﾞｱ配線②",
"WorkItems": [
"3. COVER をSCREW で取付",
"4. 外したPCｶﾊﾞｰ取付"
],
"WorkPoints": [
"取外したPCｶﾊﾞｰを取付"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "銘板貼付治具",
"Size": "",
"ToolOther": "FM-3225",
"WorkName": "ｼﾘｱﾙﾗﾍﾞﾙ貼付",
"WorkItems": [
"1. 右側後側面ｶﾊﾞｰにMEIBAN:NPM-TT2 を貼付"
],
"WorkPoints": [
"ｱﾙｺｰﾙにて清掃し､ﾗﾍﾞﾙに気泡が入らないよう貼付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"5㎜",
"10㎜... | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-3225",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付出来ている事",
"Method": "銘板貼付治具",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲ接続ｺﾈｸﾀｰｶﾊﾞｰ取付(切替仕様)",
"WorkItems": [
"1. 架台に①を付属ﾈｼﾞで取付"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側 左下ｶﾊﾞｰに取付",
"台車使用時の取付方",
"ﾄﾚｲ使用時の取付方",
"切替仕様時作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Word... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "切替仕様",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上部ｶﾊﾞｰ前組_①",
"WorkItems": [
"1. COVER にCOVER をBOLT WASHER で仮固定"
],
"WorkPoints": [
"本締め:SD-A049209-002"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに取付られている事",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "110cN･m",
"WorkName": "上部ｶﾊﾞｰ前組_②",
"WorkItems": [
"1. にCOVER をBOLT WASHER で取付ける",
"2. 完成品のｶﾊﾞｰ同士の隙間が均一である事を確認する"
],
"WorkPoints": [
"矢視",
"SD-A049209-001での仮固定箇所も締結"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"Inspectio... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾊﾞｯｸｱｯﾌﾟﾍﾞｰｽﾋﾟﾝ圧入",
"WorkItems": [
"1. BASE にPIN PIN を圧入する",
"2. BOLT WASHER は本圧着ﾄﾞｯｷﾝｸﾞ工程に払い出し"
],
"WorkPoints": [
"ﾋﾟﾝの位置と出代に注意する",
"各6P",
"出代: 20㎜",
"出代: 10㎜",
"出代: 20㎜"
],
"Tolks": [],
... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:10㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾊﾞｯｸｱｯﾌﾟﾍﾞｰｽﾋﾟﾝ圧入",
"WorkItems": [
"1. BASE にPIN PIN を圧入する",
"2. BOLT WASHER は本圧着ﾄﾞｯｷﾝｸﾞ工程に払い出し"
],
"WorkPoints": [
"ﾋﾟﾝの位置と出代に注意する",
"各6P",
"出代: 20㎜",
"出代: 10㎜",
"出代: 20㎜"
],
"Tolks": [],
... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:20㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾊﾞｯｸｱｯﾌﾟﾍﾞｰｽﾋﾟﾝ圧入",
"WorkItems": [
"1. BASE にPIN PIN を圧入する",
"2. BOLT WASHER は本圧着ﾄﾞｯｷﾝｸﾞ工程に払い出し"
],
"WorkPoints": [
"ﾋﾟﾝの位置と出代に注意する",
"各6P",
"出代: 20㎜",
"出代: 10㎜",
"出代: 20㎜"
],
"Tolks": [],
... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:20㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｰﾄｶｾｯﾄ組立",
"WorkItems": [
"4. 3.完成品にPLATE をSCREW C-RING で取付ける",
"2. PLATE に1.完成品とSHAFT をSCREW で取付ける",
"3. 2.完成品にSHAFT をC-RING で取付ける",
"1. BLOCK に砥石をかける"
],
"WorkPoints": [
"全体に砥石をかけ､ﾊﾞﾘ･ｶｴﾘ等が無いようにする"
],
"To... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼｰﾄﾎﾙﾀﾞｰﾊﾟﾈﾙ冷却ﾌﾞﾛｰ部組立",
"WorkItems": [
"1. PIPE に を で取付ける"
],
"WorkPoints": [
"仮止め:SD-A044416-031で本締め",
"矢視A",
"ｴｱｰ噴出し方向"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:2.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "空圧部組立①",
"WorkItems": [
"1. VALVE にJOINT を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "空圧部組立②",
"WorkItems": [
"1. CYLINDER にFLOATING-JOINT を取付",
"2. CYLINDER にSPEED-CONTROLLER を取付",
"3. SPEED-CONTROLLER の設定を行う",
"1. CYLINDER のﾘｰﾄﾞｽｲｯﾁ(付属)を調整"
],
"WorkPoints": [
"全閉から1.5回転開き",
"21㎜に調整",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "空圧部組立②",
"WorkItems": [
"1. CYLINDER にFLOATING-JOINT を取付",
"2. CYLINDER にSPEED-CONTROLLER を取付",
"3. SPEED-CONTROLLER の設定を行う",
"1. CYLINDER のﾘｰﾄﾞｽｲｯﾁ(付属)を調整"
],
"WorkPoints": [
"全閉から1.5回転開き",
"21㎜に調整",
"B... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "全閉から1.5回転開く",
"Method": "目視",
"RecordMethod": "WWYJ-5300-100",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "",
"ToolOther": "",
"WorkName": "空圧部組立③",
"WorkItems": [
"1. BLOCK にPLATE をBOLT WASHER で取付",
"2. BLOCK にBLOCK をWASHER BOLT で取付",
"3. と2完成品を指定寸法に取付"
],
"WorkPoints": [
"BLOCK とPLATE を端面合わせ",
"BLOCK とPLATE を端面合わせ"
],
"Tolks": [],
"Insp... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "寸法:4.5㎜±0.1㎜以内",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "BLOCK組立",
"WorkItems": [
"1. BLOCK にPIN を圧入",
"2. BLOCK にFRAME をBOLT WASHER で取付"
],
"WorkPoints": [
"出代2㎜",
"2ｾｯﾄ組立"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:2.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "BLOCK組立",
"WorkItems": [
"1. BLOCK にPIN を圧入",
"2. BLOCK にFRAME をBOLT WASHER で取付"
],
"WorkPoints": [
"出代2㎜",
"BLOCK とFRAME を定盤上で組立てる",
"2ｾｯﾄ組立"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-100",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "LMｶﾞｲﾄﾞ組立",
"WorkItems": [
"1. PLATE にPIN を圧入",
"3. PLATE にLINEAR-WAY をBOLT で仮固定",
"2. LINEAR-WAY の型式確認"
],
"WorkPoints": [
"出代1㎜",
"基準側はPINに当付け",
"型式確認"
],
"Tolks": [],
"InspectionNo": "",
"In... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:1.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LMｶﾞｲﾄﾞ組立",
"WorkItems": [
"1. PLATE にPIN を圧入",
"3. PLATE にLINEAR-WAY をBOLT で仮固定",
"2. LINEAR-WAY の型式確認"
],
"WorkPoints": [
"出代1㎜",
"基準側はPINに当付け",
"型式確認"
],
"Tolks": [],
"InspectionNo": "",
"Inspe... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-100",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "LMｶﾞｲﾄﾞ調整",
"WorkItems": [],
"WorkPoints": [
"真直度:0.02㎜以下平行度:0.02㎜以下",
"真直度:0.02㎜以下平行度:0.02㎜以下"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"Dﾋﾟﾝ",
"検査表 :2.LMｶﾞｲﾄ... | {
"QualityItem": "真直度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.02㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-100",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "LMｶﾞｲﾄﾞ調整",
"WorkItems": [],
"WorkPoints": [
"真直度:0.02㎜以下平行度:0.02㎜以下",
"真直度:0.02㎜以下平行度:0.02㎜以下"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"Dﾋﾟﾝ",
"検査表 :2.LMｶﾞｲﾄ... | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.02㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-100",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "可動ﾌﾟﾚｰﾄにﾋﾟﾝ圧入",
"WorkItems": [
"1. のLMｶﾞｲﾄﾞを取付けしていない面にPIN を圧入"
],
"WorkPoints": [
"出代3㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付け",
"WorkItems": [
"1. にLABEL を貼付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼﾘﾝﾀﾞｰ取付",
"WorkItems": [
"1. PLATE にPIN を圧入",
"2. PLATE にPIN を裏から圧入",
"1. PLATE にPIN を圧入",
"2. PLATE にPIN を裏から圧入"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words"... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼﾘﾝﾀﾞｰ取付",
"WorkItems": [
"1. PLATE にPIN を圧入",
"2. PLATE にPIN を裏から圧入",
"1. PLATE にPIN を圧入",
"2. PLATE にPIN を裏から圧入"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words"... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "全体組立①",
"WorkItems": [
"1. に をBOLT WASHER で取付ける",
"2. にBOLT WASHER を取付ける"
],
"WorkPoints": [
"ｱﾙﾐﾌﾚｰﾑはﾋﾟﾝに当付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "全体組立②",
"WorkItems": [
"1. に をBOLT で取付",
"2. にWASHER LEVER を取付",
"3. 2.完成品に をBOLT WASHER で取付"
],
"WorkPoints": [
" がｽﾑｰｽﾞに可動すること",
"矢視図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "全体組立③",
"WorkItems": [
"1. を上部と下部に分離する"
],
"WorkPoints": [
"赤〇のﾎﾞﾙﾄ4本を外す",
"外すﾎﾞﾙﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "全体組立④",
"WorkItems": [
"1. の下部に をBOLT で取付",
"2. の下部に の上部を取付"
],
"WorkPoints": [
" のPINが に当っていること",
"前ﾍﾟｰｼﾞで外したﾎﾞﾙﾄ(M5×12)を使用",
"1㎜以上"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-47",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3m",
"ToolOther": "",
"WorkName": "配管接続①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3m",
"ToolOther": "",
"WorkName": "配管接続②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管固定",
"WorkItems": [
"1. の配管を㉖で固定する",
"2. 1.完成品とBRACKET BOLT WASHER を次工程に払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "空圧部組立①",
"WorkItems": [
"1. VALVE にJOINT JOINT を組付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "空圧部組立②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1.PLATE に をBOLT WASHER で組付ける",
"2.1の完成品にMANIFOLD をBOLT WASHER で組付ける"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "空圧部組立③",
"WorkItems": [],
"WorkPoints": [
"SPEED-CONTROLLER のｽﾋﾟｺﾝは全閉から4回転開いてﾛｯｸしておく事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1. にSPEED-CONTROLLER をBOLT WASHER WASHER で組付ける",
"2.1... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "全閉から4回転開く",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "空圧部組立④",
"WorkItems": [
"3. 2の完成品にJOINT JOINT をBOLT WASHER WASHER で組付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"JOINT φ8を下にする",
"1. にJOINT を挿入する",
"2.1の完成品に... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.