input stringclasses 1
value | instruction stringlengths 202 3.29k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊｰﾈｽ準備2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1.下記ﾘｽﾄの順番でｹｰﾌﾞﾙを準備する"
]
} | {
"QualityItem": "ｹｰﾌﾞﾙの準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "付属品準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1.下記ﾘｽﾄで付属品を準備する"
]
} | {
"QualityItem": "ｹｰﾌﾞﾙの準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1/2/3aV001",
"1/3/5aF1508",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1/2/3bV001",
"1a/2a/3aX1601",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回3",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1X002",
"16X0500",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回4",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"7X006",
"16X0501",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回5",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"72X1500/73X1500/74X150029X1500/40X1500/51X1500",
"11X1001/12X1001/13X100151X1001/52X1001/5... | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回6",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"7X009",
"E1K4106",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回7",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"6X009",
"E1K4105",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回8",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"5X009",
"E1K4109",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回9",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1X003",
"E1K4116",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回10",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"75X1500/76X1500/77X150026X1500/37X1500/48X1500",
"11X1002/12X1002/13X100251X1002/52X1002/... | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回11",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1X009",
"E1K4110",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回12",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"3X009",
"E1K4108",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回13",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"8X004",
"E1K4118",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回14",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"12/16/23X1500",
"ACINA101",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回15",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"35/46/22X1500",
"ACINA004",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回16",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"16X006",
"2X002",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回17",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"9X002",
"16X004",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回18",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"11X002",
"16X009",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回19",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"6X002",
"4X010",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回20",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"60X1500/62X1500/64X150027X1500/49X1500",
"XAK4101/XAK4401",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回21",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"4X009",
"E1K4107",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回22",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"2X009",
"E1K4111",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回23",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"15X002",
"16X003",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回24",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"61X1500/63X1500/65X150028X1500/50X1500",
"XAK4102",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回25",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"3X003",
"E1K4102",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回26",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"78X1500/79X1500/80X150030X1500/41X1500/52X1500",
"11X1003/12X1003/13X100351X1003/52X1003/... | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回27",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"61X1001/62X1001/63X100121X1001/23X1001",
"XAK4112/XAK4114/XAK4115/XAK4113",
"1. CABL... | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回28",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"81X1001/82X1001/83X100141X1001/43X1001",
"XAK4116",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回29",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"71X1001/72X1001/73X1001/31X1001/33X1001",
"XAK4130/XAK4131",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回30",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"61X1003/62X1003/63X100322X1003/23X1003",
"XAK4124/XAK4125/XAK4123",
"1. CABLE を引き回す"... | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回31",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"81X1003/82X1003/83X100342X1003/43X1003",
"XAK4122",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回32",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"71X1003/72X1003/73X100332X1003/33X1003",
"XAK4126",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回33",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"61X1002/62X1002/63X100221X1002/22X1002",
"XAK4111/XAK4110/XAK4108",
"1. CABLE を引き回す"... | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回34",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"120X1600/112X16001bX1601/2bX1601/3bX1601",
"(基準)P1ACP",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回35",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"7X004",
"E1K4119",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回36",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"9X004",
"E1K4117",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回37",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"5X003",
"E1K4124",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回38",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"6X003",
"E1K4125",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回39",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"4X003",
"E1K4123",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回40",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"8X003",
"E1K4128",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回41",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"7X003",
"E1K4129",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回42",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"9X003",
"E1K4127",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回43",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"2X003",
"E1K4122",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回44",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"8X009",
"E1K4126",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回45",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"66X1500/68X1500/70X1500/81X150082X1500/83X1500/31X1500/53X150032X1500/43X1500",
"P1SVD1P"... | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回46",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"127X1600/119X1600",
"ACLaT161/ACNaT161",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回47",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ACF23R",
"11X006",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回48",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ACF24R",
"12X006",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ﾊｰﾈｽ引き回49",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"U200T001/V200T001/W200T001",
"4aV001/5aV001/6aV001",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6410",
"WorkName": "ｲﾝｼｭﾛｯｸ固定",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1. ｲﾝｼｭﾛｯｸで固定する",
"⇒100mm",
"⇒150mm",
"⇒200mm",
"⇒250mm"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6410",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "上下駆動部組立①",
"WorkItems": [
"1. BRACKET にPIN PIN を圧入する",
"3. 2.完成品にLINEAR-WAY をBOLT で取付ける"
],
"WorkPoints": [
"ﾋﾟﾝに当付ける",
"出代:1㎜",
"出代:5㎜",
"出代:3㎜",
"平行度 20μm以下",
"ﾎﾟｽﾄ高さ"
],
"Tolks": [],... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代1.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "上下駆動部組立①",
"WorkItems": [
"1. BRACKET にPIN PIN を圧入する",
"3. 2.完成品にLINEAR-WAY をBOLT で取付ける"
],
"WorkPoints": [
"ﾋﾟﾝに当付ける",
"出代:1㎜",
"出代:5㎜",
"出代:3㎜",
"平行度 20μm以下",
"ﾎﾟｽﾄ高さ"
],
"Tolks": [],... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "上下駆動部組立①",
"WorkItems": [
"1. BRACKET にPIN PIN を圧入する",
"3. 2.完成品にLINEAR-WAY をBOLT で取付ける"
],
"WorkPoints": [
"ﾋﾟﾝに当付ける",
"出代:1㎜",
"出代:5㎜",
"出代:3㎜",
"平行度 20μm以下",
"ﾎﾟｽﾄ高さ"
],
"Tolks": [],... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "上下駆動部組立①",
"WorkItems": [],
"WorkPoints": [
"平行度 20μm以下",
"ﾎﾟｽﾄ高さ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"WWYJ-5300-082"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "20μm以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-082",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "上下駆動部組立②",
"WorkItems": [],
"WorkPoints": [
"0.5㎜±0.5㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "上下駆動部組立②",
"WorkItems": [],
"WorkPoints": [
"0.5㎜±0.5㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "段差確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "段差:0.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "上下駆動部組立②",
"WorkItems": [],
"WorkPoints": [
"0.5㎜±0.5㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上下駆動部組立③",
"WorkItems": [
"1. にSPRING を取付ける",
"3. 2.完成品にSENSOR をBOLT WASHER WASHER で取付ける",
"4. 3.完成品にOIL-PAN をBOLT で取付ける",
"2. 1.完成品にDOG をBOLT で取付ける"
],
"WorkPoints": [
"ｽﾌﾟﾘﾝｸﾞの方向を合わせること"
],
"Tolks": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θ部ﾍﾞｰｽ組立",
"WorkItems": [
"1. PLATE にPIN PIN を圧入する"
],
"WorkPoints": [
"出代:3㎜",
"出代:4.5㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θ部ﾍﾞｰｽ組立",
"WorkItems": [
"1. PLATE にPIN PIN を圧入する"
],
"WorkPoints": [
"出代:3㎜",
"出代:4.5㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:4.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θﾓｰﾀｰ部組立",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNO.を記入する",
"2. BLOCK にMOTOR をBOLT で取付ける",
"3. に2.完成品をBOLT で取付ける",
"4. 3.完成品にLEVER をBOLT で取付ける"
],
"WorkPoints": [
"隙間を3.5㎜に合わせる事",
"型式:PK523PA-A6",
"ｼﾘｱﾙ... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-082",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θﾓｰﾀｰ部組立",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNO.を記入する",
"2. BLOCK にMOTOR をBOLT で取付ける",
"3. に2.完成品をBOLT で取付ける",
"4. 3.完成品にLEVER をBOLT で取付ける"
],
"WorkPoints": [
"隙間を3.5㎜に合わせる事",
"型式:PK523PA-A6",
"ｼﾘｱﾙ... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-082",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θﾓｰﾀｰ部組立",
"WorkItems": [],
"WorkPoints": [
"隙間を3.5㎜に合わせる事",
"型式:PK523PA-A6"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間3.5㎜に合わせる",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θﾌﾟﾚｰﾄｶﾞｲﾄﾞ部組立",
"WorkItems": [
"1. にPIN BEARING COLLAR をBOLT WASHER BOLT で取付ける",
"2. 1.完成品にBEARING COLLAR PIN をNUT で取付ける"
],
"WorkPoints": [
"BOLT を先に締結しBOLT を仮止め",
"SD-A044687-012で本止め",
"COLLAR がPIN のﾈｼﾞ部に噛み込まな... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θ部組立",
"WorkItems": [
"2. PLATE にPIN を圧入する"
],
"WorkPoints": [
"出代:4.5㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:4.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "5.5㎜",
"ToolOther": "0.39N･m",
"WorkName": "θ部組立",
"WorkItems": [
"1. PLATE にCAM-FOLLOWER をNUT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 0.39N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "0.39N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "反転ﾓｰﾀｰ組立①",
"WorkItems": [],
"WorkPoints": [
"出代:左右1.5㎜",
"ﾌﾟｰﾘ溝"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:左右共に1.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "反転ﾓｰﾀｰ組立②",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNO.を記入する",
"2. にCOUPLING を挿入し付属ﾎﾞﾙﾄで取付ける",
"3. 2.完成品にMOTOR をBOLT で取付ける",
"4. 3.完成品にDOG をSCREW で取付ける"
],
"WorkPoints": [
"型式:PK523PMB-C7",
"ｼﾘｱﾙNO.",
"ｶｯ... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-082",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "反転ﾓｰﾀｰ組立②",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNO.を記入する",
"2. にCOUPLING を挿入し付属ﾎﾞﾙﾄで取付ける",
"3. 2.完成品にMOTOR をBOLT で取付ける",
"4. 3.完成品にDOG をSCREW で取付ける"
],
"WorkPoints": [
"型式:PK523PMB-C7",
"ｼﾘｱﾙNO.",
"ｶｯ... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "反転ﾓｰﾀｰ組立②",
"WorkItems": [
"2. にCOUPLING を挿入し付属ﾎﾞﾙﾄで取付ける"
],
"WorkPoints": [
"ｶｯﾌﾟﾘﾝｸﾞ位置は隙間2㎜で調整する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"■安全作業",
"■安全作業"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間2.0㎜に調整する",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "反転ﾓｰﾀｰ組立③",
"WorkItems": [
"1. BRACKET にSENSOR をBOLT WASHER WASHER で取付ける",
"2. に1.完成品をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "反転ﾓｰﾀｰ組込み",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "反転ﾍｯﾄﾞθ部組込み",
"WorkItems": [
"1. のﾍﾞｱﾘﾝｸﾞの溝に のﾌﾟﾚｰﾄを下図のようにはめ込み､回して3個のﾍﾞｱﾘﾝｸﾞの溝にかける",
"◆2. ﾌﾟﾚｰﾄのR外周部及びﾚﾊﾞｰのU溝部にｸﾞﾘｰｽを塗布する",
"3. ﾚﾊﾞｰ溝をﾋﾟﾝにはめ込みSTOPPER SPACER をBOLT で取付ける",
"4. 3.完成品の偏心ﾋﾟﾝでｸﾘｱﾗﾝｽを調整する"
],
"WorkPoints": ... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "1㎜",
"ToolOther": "",
"WorkName": "反転ﾍｯﾄﾞθ部組込み",
"WorkItems": [],
"WorkPoints": [
"調整後2ヶ所のﾎﾞﾙﾄを本締め",
"1㎜以上の隙間がある事",
" 回転方向のｶﾞﾀ無き事",
" 上下方向のｶﾞﾀがあり小さき事",
"STOPPER 摺動抵抗2N以下である事 (全ｽﾄﾛｰｸ領域)"
],
"Tolks": [],
"InspectionNo": "",
"Insp... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:1.0㎜以上",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"Size": "2N",
"ToolOther": "",
"WorkName": "反転ﾍｯﾄﾞθ部組込み",
"WorkItems": [],
"WorkPoints": [
"調整後2ヶ所のﾎﾞﾙﾄを本締め",
"1㎜以上の隙間がある事",
" 回転方向のｶﾞﾀ無き事",
" 上下方向のｶﾞﾀがあり小さき事",
"STOPPER 摺動抵抗2N以下である事 (全ｽﾄﾛｰｸ領域)"
],
"Tolks": [],
"InspectionNo": "",
"I... | {
"QualityItem": "摺動確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "2N以下",
"Method": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-082",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "IC反転供給ﾉｽﾞﾙﾎﾙﾀﾞ部組立③",
"WorkItems": [
"◆1. ｼｬﾌﾄ部を清掃し真空ｸﾞﾘｰｽを塗布する",
"2. BLOCK にJOINT を取付け のｼｬﾌﾄに挿入する",
"3. 2.完成品にPULLEY をBOLT で取付ける",
"4. に3.完成品をBOLT で取付ける",
"5. 4.完成品にSPACER をBOLT で取付ける"
],
"WorkPoints": [
"抵... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽﾊﾞﾘｴﾙﾀ",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "IC反転供給ﾉｽﾞﾙﾎﾙﾀﾞ部組立③",
"WorkItems": [
"5. 4.完成品にSPACER をBOLT で取付ける"
],
"WorkPoints": [
"隙間"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"◆作業者安全作業",
"◆作業者安全作業"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:1㎜に設定",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着反転ﾍｯﾄﾞ部組込み①",
"WorkItems": [
"1. ﾎﾟｽﾄ部にSPRING を取付ける",
"2. 1.完成品のﾌﾟｰﾘ部にT-BELT を取付ける",
"3. 2.完成品のﾍﾞﾙﾄﾃﾝｼｮﾝを調整する"
],
"WorkPoints": [
"ｽﾌﾟﾘﾝｸﾞは下図方向で掛ける事",
"初期張力は規格の上限付近であわせること(253~288Hz)",
"裏面",
"隙... | {
"QualityItem": "ﾍﾞﾙﾄﾃﾝｼｮﾝ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "253~288Hz",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "WWYJ-5300-082",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着反転ﾍｯﾄﾞ部組込み②",
"WorkItems": [
"1. にCABLE CABLE を接続する",
"2. ｹｰﾌﾞﾙを板金と結束する",
"3. BRACKET にSENSOR をBOLT WASHER WASHER で取付ける",
"4. 2.完成品に3.完成品をBOLT で取付ける"
],
"WorkPoints": [
"IRM6203R",
"IVM6204R",
"TRIMが... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-113",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2375",
"WorkName": "仮圧着反転ﾍｯﾄﾞ部組込み③",
"WorkItems": [
"1. IR軸原点調整を行う"
],
"WorkPoints": [
"1.PHﾁｪｯｶｰを接続する",
"2.ﾉｽﾞﾙを真上に向ける",
"3.ｽﾘｯﾄをONする位置に回転",
"4.ﾁｪｯｶｰがONする位置でｶｯﾌﾟﾘﾝｸﾞを締結",
"ﾉｽﾞﾙ上向き時原点の事"
],
"Tolks": [],
"In... | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-2375",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-082",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着反転ﾍｯﾄﾞ部組込み④",
"WorkItems": [
"4. 1.完成品に2.完成品､3.完成品の順にBOLT で取付ける"
],
"WorkPoints": [
"裏面",
"側面",
"出代:5㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着反転ﾍｯﾄﾞ部組込み⑤",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける",
"2. 1.完成品にCOVER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着反転ﾍｯﾄﾞ部組込み⑥",
"WorkItems": [
"1. にCOVER をSCREW で取付ける",
"2. 1.完成品のﾍﾞｰｽﾌﾟﾚｰﾄ取付け部にBOLT WASHER を取付ける"
],
"WorkPoints": [
"4ヶ所を手締め",
"反転ﾍｯﾄﾞ底面",
"脱落防止ﾎﾞﾙﾄ"
],
"Tolks": [],
"InspectionNo": "",
"Inspectio... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "仮圧着反転ﾍｯﾄﾞ部配管",
"WorkItems": [
"1. TUBE を指定寸法にｶｯﾄする",
"2. に1.完成品を配管する"
],
"WorkPoints": [
"φ4白ﾁｭｰﾌﾞ:530㎜",
"ｼﾞｮｲﾝﾄに接続",
"ﾌﾟﾚｰﾄ穴を通す",
"ﾁｭｰﾌﾞの結束は､次ﾍﾟｰｼﾞ以降のｹｰﾌﾞﾙ配線と合わせて行う",
"ﾌﾟﾚｰﾄ穴までの配管長さ目安 75㎜",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着反転ﾍｯﾄﾞ部配線①",
"WorkItems": [
"1. にCABLE CABLE を接続する"
],
"WorkPoints": [
"B13132R",
"B13130R",
"B13133R",
"2IVM6204P",
"2IVM6204R",
"B10905R",
"1IRM6203R",
"1IRM6203P",
"B13120R"
],
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-113",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮圧着反転ﾍｯﾄﾞ部配線②",
"WorkItems": [
"1. のｹｰﾌﾞﾙを配線し結束する"
],
"WorkPoints": [
"IR軸ﾓｰﾀｰの配線が､P17ﾌﾟﾚｰﾄの下面より下に出無い事",
"P017",
"IR軸ﾓｰﾀｰ配線は､P604から45㎜以内に引き回の事",
"P604",
"矢視A(裏面)",
"このｹｰﾌﾞﾙは､ﾌﾞﾗｹｯﾄ裏面側で結束する",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着移載ｲｵﾅｲｻﾞｰ部_(正流れ)_組立①",
"WorkItems": [
"1. IONIZER の部品確認を行う",
"2. IONIZER にNOZZLE を取付ける",
"3. BRACKET に2完成品をBOLT で取付ける",
"4. 3完成品にSPEED-CONTROLLER をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ｲｵﾅｲｻﾞｰ付属ｹｰﾌﾞﾙ",
... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWXJ-5300-062",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着移載ｲｵﾅｲｻﾞｰ部_(正流れ)_組立①",
"WorkItems": [
"1. IONIZER の部品確認を行う",
"2. IONIZER にNOZZLE を取付ける",
"3. BRACKET に2完成品をBOLT で取付ける",
"4. 3完成品にSPEED-CONTROLLER をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ｲｵﾅｲｻﾞｰ付属ｹｰﾌﾞﾙ",
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWXJ-5300-062",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "12㎜",
"ToolOther": "8.0N･m",
"WorkName": "仮圧着移載ｲｵﾅｲｻﾞｰ部_(正流れ)_組立①",
"WorkItems": [
"1. IONIZER の部品確認を行う",
"2. IONIZER にNOZZLE を取付ける"
],
"WorkPoints": [
"ｲｵﾅｲｻﾞｰ付属ｹｰﾌﾞﾙ",
"取付け向きに注意",
"･部品の型式が検査表と一致する事･ｼﾘｱﾙ№を検査表に記入する"
],
"Tolks": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "8.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着移載ｲｵﾅｲｻﾞｰ部_(正流れ)_組立②",
"WorkItems": [
"1. をBRACKET にBOLT WASHER で取付ける",
"3. 2.完成品にCABLE-SUPPORT を取付ける",
"2. 1.完成品にCLIP BOLT を取付ける"
],
"WorkPoints": [
"A矢視"
],
"Tolks": [],
"InspectionNo": "",
"Inspectio... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "仮圧着移載ｲｵﾅｲｻﾞｰ部_(正流れ)_組立③",
"WorkItems": [
"1. TUBE を右記の寸法にｶｯﾄする",
"2. に1完成品を接続する",
"■3. 2完成品にCABLE をBOLT WASHER WASHER で取付ける",
"4. 3完成品にｲｵﾅｲｻﾞｰ付属ｹｰﾌﾞﾙを接続しLABEL TERMINAL PROCESS を取付ける",
"5. 配線配管をｲﾝｼｭﾛｯｸで固定する"
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "62cN･m",
"WorkName": "仮圧着移載ｲｵﾅｲｻﾞｰ部_(正流れ)_組立③",
"WorkItems": [
"1. TUBE を右記の寸法にｶｯﾄする",
"2. に1完成品を接続する",
"■3. 2完成品にCABLE をBOLT WASHER WASHER で取付ける",
"4. 3完成品にｲｵﾅｲｻﾞｰ付属ｹｰﾌﾞﾙを接続しLABEL TERMINAL PROCESS を取付ける",
"5. 配線配管をｲﾝｼｭﾛｯ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "62cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6427",
"WorkName": "ﾏｸﾞﾈｯﾄ取付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1. ﾊｰﾈｽﾎﾞｰﾄﾞにﾏｸﾞﾈｯﾄを取付ける",
"⇒ﾏｸﾞﾈｯﾄ中",
"⇒ﾏｸﾞﾈｯﾄ大"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6427",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊｰﾈｽ準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"1.下記ﾘｽﾄの順番でｹｰﾌﾞﾙを準備する"
]
} | {
"QualityItem": "ｹｰﾌﾞﾙの準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6427",
"WorkName": "ﾊｰﾈｽ引き回1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"P1PLS1R",
"CN2K3130",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6427",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6427",
"WorkName": "ﾊｰﾈｽ引き回2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"P1EMGR",
"PLED2P",
"P1COV5P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6427",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6427",
"WorkName": "ﾊｰﾈｽ引き回3",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"P1HTR",
"CN11K003",
"CNSFA012",
"P2HTP",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6427",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6427",
"WorkName": "ﾊｰﾈｽ引き回4",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"P1COVDIR",
"P2COVDIP",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6427",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.