input stringclasses 1
value | instruction stringlengths 202 3.29k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し①",
"WorkItems": [
"1. のﾌｧｲﾊﾞｰｾﾝｻを引き回す",
"2. 1完成品にBOLT WASHER を取付"
],
"WorkPoints": [
"ﾌｧｲﾊﾞｰ線の根元が折れないように注意の事",
"ﾌｧｲﾊﾞｰ線の根元が折れないように注意の事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"Inspectio... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾚｰﾝ2可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し①",
"WorkItems": [
"1. のﾌｧｲﾊﾞｰｾﾝｻを引き回す",
"2. 1完成品にBOLT WASHER を取付"
],
"WorkPoints": [
"ﾌｧｲﾊﾞｰ線の根元が折れないように注意の事",
"ﾌｧｲﾊﾞｰ線の根元が折れないように注意の事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し②",
"WorkItems": [
"1. のﾌｧｲﾊﾞｰｾﾝｻを引き回す",
"2. 1完成品にBOLT WASHER を取付"
],
"WorkPoints": [
"ﾌｧｲﾊﾞｰ線の根元が折れないように注意の事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems":... | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾚｰﾝ2可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し②",
"WorkItems": [
"1. のﾌｧｲﾊﾞｰｾﾝｻを引き回す",
"2. 1完成品にBOLT WASHER を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【選択仕様:逆流れ】ﾚｰﾝ2可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し",
"WorkItems": [
"1. のﾌｧｲﾊﾞｰｾﾝｻを引き回す"
],
"WorkPoints": [
"L1側",
"L2側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP:ｽﾗｲﾄﾞ搬送仕様】ﾚｰﾝ2可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し",
"WorkItems": [
"1. のﾌｧｲﾊﾞｰｾﾝｻを引き回す"
],
"WorkPoints": [
"L1側",
"L2側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾚｰﾝ2可動側ﾀﾞｸﾄ取付",
"WorkItems": [
"2. 1完成品にDUCT をBOLT WASHER で取付",
"1. にDUCT をBOLT WASHER で取付",
"2. 1完成品にDUCT をBOLT WASHER で取付",
"1. にDUCT をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ﾚｰﾝ2可動側左側ﾍﾞｱ整線①",
"WorkItems": [
"2. 1完成品に㉘で配線を固定",
"■1. のFG線をSCREW で取付",
"3. ﾍﾞｱ配線のCABLE CABLE のｺﾈｸﾀをﾌﾞﾗｹｯﾄに取付",
"4. ﾚｰﾙ側配線をｺﾈｸﾀに挿入"
],
"WorkPoints": [
"B125P",
"B1027P",
"FGCVM4",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2可動側左側ﾍﾞｱ整線②",
"WorkItems": [
"1. TUBE に のﾌｧｲﾊﾞｰを通す",
"2. CABLE-BEAR のふたを開け配線を入れる",
"3. CABLE-BEAR のふたを閉じて､ﾚｰﾙ側の固定金具に取付",
"4. 下側の固定金具に取付"
],
"WorkPoints": [
"L2側",
"L1側",
"A矢視",
"上側",
"下側",
... | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2可動側左側ﾍﾞｱ整線②",
"WorkItems": [
"1. TUBE に のﾌｧｲﾊﾞｰを通す",
"2. CABLE-BEAR のふたを開け配線を入れる",
"3. CABLE-BEAR のふたを閉じて､ﾚｰﾙ側の固定金具に取付",
"4. 下側の固定金具に取付"
],
"WorkPoints": [
"L2側",
"L1側",
"A矢視",
"上側",
"下側",
... | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2可動側右側ﾍﾞｱ整線②",
"WorkItems": [
"1. TUBE に のﾌｧｲﾊﾞｰを通す",
"2. CABLE-BEAR のふたを開け配線を入れる",
"3. CABLE-BEAR のふたを閉じて､ﾚｰﾙ側の固定金具に取付",
"4. 下側の固定金具に取付"
],
"WorkPoints": [
"L2側",
"L1側",
"通してあるｲﾝｼｭﾛｯｸにて固定",
"A矢視... | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2可動側右側ﾍﾞｱ整線②",
"WorkItems": [
"1. TUBE に のﾌｧｲﾊﾞｰを通す",
"2. CABLE-BEAR のふたを開け配線を入れる",
"3. CABLE-BEAR のふたを閉じて､ﾚｰﾙ側の固定金具に取付",
"4. 下側の固定金具に取付"
],
"WorkPoints": [
"L2側",
"L1側",
"通してあるｲﾝｼｭﾛｯｸにて固定",
"A矢視... | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ﾚｰﾝ2可動側右側ﾍﾞｱ整線①",
"WorkItems": [
"■1. のFG線をSCREW で取付",
"2. 1完成品をｲﾝｼｭﾛｯｸで固定",
"3. ﾍﾞｱ配線のCABLE のｺﾈｸﾀをﾌﾞﾗｹｯﾄに取付"
],
"WorkPoints": [
"B1127P",
"FGCVM5"
],
"Tolks": [],
"InspectionNo": "",... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側配線①",
"WorkItems": [
"1. にCABLE を引き回す"
],
"WorkPoints": [
"B122R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側配線②",
"WorkItems": [
"1. にCABLE を引き回す"
],
"WorkPoints": [
"太線のみ板金と固定する事単線は単線のみで固定",
"配線が張らないようにする事",
"L2側",
"L1側",
"L1側",
"L2側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側配線①",
"WorkItems": [
"1. にCABLE を引き回す"
],
"WorkPoints": [
"B126R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側配線②",
"WorkItems": [
"1. にCABLE の配線を固定"
],
"WorkPoints": [
"L2側",
"L1側",
"太線のみ板金と固定する事単線は単線のみで固定",
"配線が張らないようにする事",
"L1側",
"L2側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ1固定側ﾏｰｸﾁｭｰﾌﾞ挿入",
"WorkItems": [
"1. ﾌｧｲﾊﾞｰ線にMARK TUBE MARK TUBE を挿入"
],
"WorkPoints": [
"ｽﾗｲﾄﾞ搬送OP仕様"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ1"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ1可動側ﾏｰｸﾁｭｰﾌﾞ挿入",
"WorkItems": [
"1. ﾌｧｲﾊﾞｰ線にMARK TUBE MARK TUBE を挿入"
],
"WorkPoints": [
"ｽﾗｲﾄﾞ搬送OP仕様"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ1"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2固定側ﾏｰｸﾁｭｰﾌﾞ挿入",
"WorkItems": [
"1. ﾌｧｲﾊﾞｰ線にMARK TUBE MARK TUBE を挿入"
],
"WorkPoints": [
"ｽﾗｲﾄﾞ搬送OP仕様"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ1"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2可動側ﾏｰｸﾁｭｰﾌﾞ挿入",
"WorkItems": [
"1. ﾌｧｲﾊﾞｰ線にMARK TUBE MARK TUBE を挿入"
],
"WorkPoints": [
"ｽﾗｲﾄﾞ搬送OP仕様"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ1"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側配線ﾌﾞﾗｹｯﾄ固定側ﾌｧｲﾊﾞｰ引き回し確認",
"WorkItems": [
"1. のﾌｧｲﾊﾞｰｾﾝｻの引き回し確認"
],
"WorkPoints": [
"図の通り引き回しされている事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側配線ﾌﾞﾗｹｯﾄ可動側ﾌｧｲﾊﾞｰ整線",
"WorkItems": [
"3. 2完成品にCABLE を引き回し",
"1. のﾌｧｲﾊﾞｰｾﾝｻを固定",
"2. JOINT にTUBE を接続"
],
"WorkPoints": [
"延長ｺﾝﾍﾞﾔｰ仕様時",
"通してあるｲﾝｼｭﾛｯｸに固定",
"TUBE ﾏｰｷﾝｸﾞ位置",
"延長仕様の場合､ﾊﾞﾙﾌﾞ側ｼﾞｮｲﾝﾄに接続",
... | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側ﾌｧｲﾊﾞｰ線接続",
"WorkItems": [
"1. のﾌｧｲﾊﾞｰ線接続"
],
"WorkPoints": [
"付属のﾌｧｲﾊﾞｰｶｯﾀｰでｶｯﾄして接続する",
"上段:可動側(黄)",
"下段:固定側(白)",
"ﾌｧｲﾊﾞｰ線を奥まで挿入する事",
"ﾌｧｲﾊﾞｰﾛｯｸﾚﾊﾞｰがﾛｯｸされている事"
],
"Tolks": [],
"InspectionNo": "",... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り配線･配管出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側配線ﾌﾞﾗｹｯﾄ固定側ﾌｧｲﾊﾞｰ引き回し確認",
"WorkItems": [
"1. のﾌｧｲﾊﾞｰｾﾝｻの引き回し確認"
],
"WorkPoints": [
"図の通り引き回しされている事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側配線ﾌﾞﾗｹｯﾄ可動側ﾌｧｲﾊﾞｰ整線",
"WorkItems": [
"1. のﾌｧｲﾊﾞｰｾﾝｻを固定"
],
"WorkPoints": [
"通してあるｲﾝｼｭﾛｯｸに固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ｲﾝｼｭﾛｯｸ指示",
... | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側ﾌｧｲﾊﾞｰｾﾝｻ接続",
"WorkItems": [
"1. のﾌｧｲﾊﾞｰ線接続"
],
"WorkPoints": [
"付属のﾌｧｲﾊﾞｰｶｯﾀｰでｶｯﾄして接続する",
"上段:可動側(黄)",
"下段:固定側(白)",
"ﾌｧｲﾊﾞｰ線を奥まで挿入する事",
"ﾌｧｲﾊﾞｰﾛｯｸﾚﾊﾞｰがﾛｯｸされている事"
],
"Tolks": [],
"InspectionNo": "... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｱﾝﾌﾟｶﾊﾞｰ取付",
"WorkItems": [
"1. に を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "幅寄せﾓｰﾀｰ取付",
"WorkItems": [
"1. に をBOLT WASHER で取付"
],
"WorkPoints": [
"ﾋﾟﾝにしっかりはまっている事",
"取付前に㉚をシャフトに挿入しておく事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "幅寄せﾓｰﾀｰ取付",
"WorkItems": [
"2. 治具にてﾓｰﾀｰとｼｬﾌﾄの芯出し"
],
"WorkPoints": [
"治具を動かし､引っ掛かりが無い事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "100cN･m",
"WorkName": "幅寄せﾓｰﾀｰ取付",
"WorkItems": [
"3. 2完成品にCOUPLING を取付"
],
"WorkPoints": [
"付属ﾎﾞﾙﾄ締結",
"目視にて青丸部隙間が均等になっている事",
"COUPLING は矢印方向に当てつけながら締結"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｶｯﾌﾟﾘﾝｸﾞ治具(Φ8×Φ8)",
"Size": "",
"ToolOther": "FM-1198",
"WorkName": "幅寄せﾓｰﾀｰ取付",
"WorkItems": [
"2. 治具にてﾓｰﾀｰとｼｬﾌﾄの芯出し",
"1. に をBOLT WASHER で取付"
],
"WorkPoints": [
"治具を動かし､引っ掛かりが無い事",
"ﾋﾟﾝにしっかりはまっている事",
"取付前に㉚をシャフトに挿入しておく事"
],
"Tolks": [
"締付ﾄﾙｸ 194... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1198",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "200cN･m",
"WorkName": "上側ｶﾊﾞｰ取付",
"WorkItems": [
"1. に をSCREW SCREW で取付"
],
"WorkPoints": [
"隙間が均等になるように取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 200cN･m",
"締付ﾄﾙｸ 350cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "200cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.3",
"ToolOther": "350cN･m",
"WorkName": "上側ｶﾊﾞｰ取付",
"WorkItems": [
"1. に をSCREW SCREW で取付"
],
"WorkPoints": [
"隙間が均等になるように取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 200cN･m",
"締付ﾄﾙｸ 350cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "350cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "前面扉取付-①",
"WorkItems": [
"1. に をSCREW で取付"
],
"WorkPoints": [
"取付け方向",
"ﾌﾞﾛｯｸにて調整し平行に合わす",
"ﾌﾞﾛｯｸと扉の隙間無い事※扉がﾌﾞﾛｯｸの上に載っている事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "前面扉取付-①",
"WorkItems": [
"1. に をSCREW で取付"
],
"WorkPoints": [
"取付け方向",
"ﾌﾞﾛｯｸにて調整し平行に合わす",
"ﾌﾞﾛｯｸと扉の隙間無い事※扉がﾌﾞﾛｯｸの上に載っている事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"In... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "前面扉取付‐②",
"WorkItems": [
"1. のﾎﾞｰﾙｷｬｯﾁ位置を調整する"
],
"WorkPoints": [
"隙間を均等に合わせる",
"2.0㎜±0.5㎜",
"内側",
"外側",
"片当たりなく合わせる事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"Inspect... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "前面扉取付‐②",
"WorkItems": [
"1. のﾎﾞｰﾙｷｬｯﾁ位置を調整する"
],
"WorkPoints": [
"隙間を均等に合わせる",
"2.0㎜±0.5㎜",
"内側",
"外側",
"片当たりなく合わせる事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "前面扉取付‐③",
"WorkItems": [
"1. のﾏｸﾞﾈｯﾄｷｬｯﾁ位置を調整する",
"2. 前面扉のｶﾞﾀﾂｷの確認を行う"
],
"WorkPoints": [
"隙間を均等にする",
"ﾏｸﾞﾈｯﾄｷｬｯﾁの傾き無き事",
"内側",
"外側",
"ｶﾞﾀﾂｷ無き事",
"確認位置"
],
"Tolks": [
"締付ﾄﾙｸ 194cN... | {
"QualityItem": "取付位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "前面扉取付‐③",
"WorkItems": [
"1. のﾏｸﾞﾈｯﾄｷｬｯﾁ位置を調整する"
],
"WorkPoints": [
"隙間を均等にする",
"ﾏｸﾞﾈｯﾄｷｬｯﾁの傾き無き事",
"内側",
"外側"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"Inspectio... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前面扉取付‐③",
"WorkItems": [
"1. のﾏｸﾞﾈｯﾄｷｬｯﾁ位置を調整する",
"2. 前面扉のｶﾞﾀﾂｷの確認を行う"
],
"WorkPoints": [
"ｶﾞﾀﾂｷ無き事",
"隙間を均等にする",
"ﾏｸﾞﾈｯﾄｷｬｯﾁの傾き無き事",
"内側",
"外側",
"確認位置"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｶﾞﾀつき無き事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "前面扉取付‐④",
"WorkItems": [
"1. のﾛｯｸｼﾘﾝﾀﾞｰを調整する",
"■2. 安全SWの位置調整を行う"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが接触なく出入りする事",
"ON",
"OFF",
"ｽｲｯﾁ同士のｽﾞﾚ無き事"
],
"Tolks": [],
"InspectionNo": "",
"Inspe... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前面扉取付‐④",
"WorkItems": [
"1. のﾛｯｸｼﾘﾝﾀﾞｰを調整する",
"■2. 安全SWの位置調整を行う"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが接触なく出入りする事",
"傾き無き事",
"ON",
"OFF",
"中心に合わせる事",
"1~2.5㎜",
"SW固定ﾎﾞﾙﾄを合わす",
"ｽｲｯﾁ同士のｽﾞﾚ無き事"
],... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "干渉なく出入りする事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "前面扉取付‐④",
"WorkItems": [
"1. のﾛｯｸｼﾘﾝﾀﾞｰを調整する",
"■2. 安全SWの位置調整を行う"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが接触なく出入りする事",
"ON",
"OFF",
"ｽｲｯﾁ同士のｽﾞﾚ無き事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems"... | {
"QualityItem": "位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間1㎜~2.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｱｸﾘﾙ開閉ｶﾊﾞｰ調整",
"WorkItems": [
"1. の補給部PC開閉ｶﾊﾞｰ段差調整",
"2. ｽｲｯﾁ調整"
],
"WorkPoints": [
"段差:0.5~2.0㎜",
"前面扉",
"PCｶﾊﾞｰ",
"傾き無い事"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "50cN･m",
"WorkName": "ｱｸﾘﾙ開閉ｶﾊﾞｰ調整",
"WorkItems": [
"1. の補給部PC開閉ｶﾊﾞｰ段差調整",
"2. ｽｲｯﾁ調整",
"1. の補給部PC開閉ｶﾊﾞｰ段差調整",
"2. ｽｲｯﾁ調整"
],
"WorkPoints": [
"段差:0.5~2.0㎜",
"前面扉",
"PCｶﾊﾞｰ",
"傾き無い事",
"段差:0.5~2.0... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｱｸﾘﾙ開閉ｶﾊﾞｰ調整",
"WorkItems": [
"1. の補給部PC開閉ｶﾊﾞｰ段差調整",
"2. ｽｲｯﾁ調整"
],
"WorkPoints": [
"段差:0.5~2.0㎜",
"前面扉",
"PCｶﾊﾞｰ",
"傾き無い事"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"Ins... | {
"QualityItem": "位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間0.5㎜~2.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側ｼｬｯﾀｰｼｬﾌﾄ取付",
"WorkItems": [
"1. SHAFT にBOLT WASHER を仮取付",
"2. 1完成品を に挿入し固定ﾎﾞﾙﾄを仮止め"
],
"WorkPoints": [
"左側上ｱｰﾑ",
"ﾎﾞﾙﾄ側が上",
"ｼｬｯﾀｰｼｬﾌﾄ挿入穴",
"左側下ｱｰﾑ",
"ｼｬｯﾀｰｼｬﾌﾄ挿入穴",
"Dｶｯﾄ",
"Dｶｯﾄをﾎﾞﾙﾄ側に合わせる... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "左側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜ｼﾑが入ら無い事",
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付ﾎﾞﾙﾄを仮... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "左側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜ｼﾑが入ら無い事",
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付ﾎﾞﾙﾄを仮止... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "左側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜ｼﾑが入ら無い事",
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側ｼｬｯﾀｰｼｬﾌﾄ取付",
"WorkItems": [
"1. SHAFT にBOLT WASHER を仮取付",
"2. 1完成品を に挿入し固定ﾎﾞﾙﾄを仮止め"
],
"WorkPoints": [
"右側上ｱｰﾑ",
"左側上ﾌﾟﾚｰﾄ",
"ｼｬｯﾀｰｼｬﾌﾄ挿入穴",
"右側下ｱｰﾑ",
"ｼｬｯﾀｰｼｬﾌﾄ挿入穴",
"ﾎﾞﾙﾄ側が上",
"Dｶｯﾄをﾎﾞﾙﾄ側に... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視手感",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "右側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付ﾎﾞﾙﾄを仮止め",
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜ｼﾑが入ら無... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "右側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付ﾎﾞﾙﾄを仮止め",
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜ｼﾑが入ら無い... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "右側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付ﾎﾞﾙﾄを仮止め",
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(ﾒｶｽﾄｯﾊﾟｰ位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"1. のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置(原点)まで下降させる"
],
"WorkPoints": [
"治具を当付け隙間無い事(0.01㎜)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(ﾒｶｽﾄｯﾊﾟｰ位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"1. のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置(原点)まで下降させる"
],
"WorkPoints": [
"治具を当付け隙間無い事(0.01㎜)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(ﾒｶｽﾄｯﾊﾟｰ位置)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"上面",
"ｼｬﾌﾄ",
"ｼｬﾌﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(ﾒｶｽﾄｯﾊﾟｰ位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"1. のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置(原点)まで下降させる"
],
"WorkPoints": [
"治具を当付け隙間無い事(0.01㎜)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除治具(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(ﾒｶｽﾄｯﾊﾟｰ位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"1. のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置(原点)まで下降させる"
],
"WorkPoints": [
"治具を当付け隙間無い事(0.01㎜)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(LMｶﾞｲﾄﾞ上端位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"3. 上側ｼｬｯﾀｰ部の位置を調整する",
"1. のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置まで上昇する"
],
"WorkPoints": [
"ｼｬﾌﾄを治具に当付ける",
"治具を当付け隙間無い事(0.01㎜)"
],
"Tolks": [],
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(LMｶﾞｲﾄﾞ上端位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"3. 上側ｼｬｯﾀｰ部の位置を調整する",
"1. のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置まで上昇する"
],
"WorkPoints": [
"ｼｬﾌﾄを治具に当付ける",
"治具を当付け隙間無い事(0.01㎜)"
],
"Tolks": [],
"Inspect... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(LMｶﾞｲﾄﾞ上端位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"3. 上側ｼｬｯﾀｰ部の位置を調整する",
"1. のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置まで上昇する"
],
"WorkPoints": [
"ｼｬﾌﾄを治具に当付ける",
"治具を当付け隙間無い事(0.01㎜)"
],
"Tolks": [],
"Inspect... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(LMｶﾞｲﾄﾞ上端位置)",
"WorkItems": [],
"WorkPoints": [
"上端位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除治具(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(LMｶﾞｲﾄﾞ上端位置)",
"WorkItems": [],
"WorkPoints": [
"上端位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ ②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目 ②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事... | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けできていること",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ ②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目 ②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.02㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ ②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目 ②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ ②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目 ②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.15㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ ②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目 ②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ ②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目 ②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "前面扉ｶﾞｲﾄﾞﾞ隙間調整",
"WorkItems": [],
"WorkPoints": [
"ﾏｶﾞｼﾞﾝｼｬｯﾀｰ閉のこと",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ﾌﾞﾗｹｯﾄ",
"ﾆｭｰﾗｲﾄﾃｰﾌﾟ",
"0.4㎜が通り0.5㎜が通ら無い事",
"ﾄﾚｲﾊﾟﾚｯﾄ各5･19ｽﾛｯﾄに挿入",
"ﾄﾚｲﾊﾟﾚｯﾄをｼｬﾌﾄに当付ける",
"橙丸のﾎﾞﾙﾄを締めてけて固定す... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.4㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "前面扉ｶﾞｲﾄﾞﾞ隙間調整",
"WorkItems": [],
"WorkPoints": [
"ﾏｶﾞｼﾞﾝｼｬｯﾀｰ閉のこと",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ﾌﾞﾗｹｯﾄ",
"ﾆｭｰﾗｲﾄﾃｰﾌﾟ",
"0.4㎜が通り0.5㎜が通ら無い事",
"ﾄﾚｲﾊﾟﾚｯﾄ各5･19ｽﾛｯﾄに挿入",
"ﾄﾚｲﾊﾟﾚｯﾄをｼｬﾌﾄに当付ける",
"橙丸のﾎﾞﾙﾄを締めてけて固定す... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "前面扉ｶﾞｲﾄﾞﾞ隙間調整",
"WorkItems": [],
"WorkPoints": [
"ﾏｶﾞｼﾞﾝｼｬｯﾀｰ閉のこと",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ﾌﾞﾗｹｯﾄ",
"ﾆｭｰﾗｲﾄﾃｰﾌﾟ",
"0.4㎜が通り0.5㎜が通ら無い事",
"ﾄﾚｲﾊﾟﾚｯﾄ各5･19ｽﾛｯﾄに挿入",
"ﾄﾚｲﾊﾟﾚｯﾄをｼｬﾌﾄに当付ける",
"橙丸のﾎﾞﾙﾄを締めてけて固定... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "前面扉押込み防止ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"1. の押込み防止ｽﾄｯﾊﾟｰとﾌﾚｰﾑの隙間を調整する"
],
"WorkPoints": [
"説明の為に前面扉は消しています",
"ﾌﾚｰﾑに当付ける",
"平行に取付け"
],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m"
],
"InspectionNo": "",
"Insp... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "補給部前側ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"2. 補給部ｽﾄｯﾊﾟｰの隙間を確認する",
"1. にﾄﾚｲﾊﾟﾚｯﾄを挿入し補給部ｽﾄｯﾊﾟｰを調整する",
"2. 補給部ｽﾄｯﾊﾟｰの隙間を確認する",
"1. にﾄﾚｲﾊﾟﾚｯﾄを挿入し補給部ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄｽ... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.4㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "補給部前側ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"2. 補給部ｽﾄｯﾊﾟｰの隙間を確認する",
"1. にﾄﾚｲﾊﾟﾚｯﾄを挿入し補給部ｽﾄｯﾊﾟｰを調整する",
"2. 補給部ｽﾄｯﾊﾟｰの隙間を確認する",
"1. にﾄﾚｲﾊﾟﾚｯﾄを挿入し補給部ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄｽ... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "補給部前側ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"2. 補給部ｽﾄｯﾊﾟｰの隙間を確認する",
"1. にﾄﾚｲﾊﾟﾚｯﾄを挿入し補給部ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰ",
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "NG排出部ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"1. のNG排出部にﾄﾚｲﾊﾟﾚｯﾄを挿入する",
"2. NG排出ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.4㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "NG排出部ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"1. のNG排出部にﾄﾚｲﾊﾟﾚｯﾄを挿入する",
"2. NG排出ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "NG排出部ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"1. のNG排出部にﾄﾚｲﾊﾟﾚｯﾄを挿入する",
"2. NG排出ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "補給部ﾗﾍﾞﾙ貼付け",
"WorkItems": [
"1. にLABEL を貼付ける"
],
"WorkPoints": [
"ﾗﾍﾞﾙの端面がﾄﾚｲﾊﾟﾚｯﾄに隠れ無い事",
"ｱﾙｺｰﾙ使用時には保護ﾒｶﾞﾈ着用の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"60㎜",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾁｪｯｶｰ接続と立ち上げ",
"WorkItems": [
"3. PC画面が立ち上がったらNPM-GWのｱｲｺﾝをﾀﾞﾌﾞﾙｸﾘｯｸ",
"5. ｼｽﾃﾑ立ち上げ",
"1. ﾄﾚｲ本体とﾁｪｯｶｰを接続する",
"2. ﾁｪｯｶｰのﾊﾟｿｺﾝの立ち上げ",
"4.ﾁｪｯｶｰの電源BOXとｻｰﾎﾞSWをON"
],
"WorkPoints": [
"･ﾁｪｯｶｰ電源接... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整①",
"WorkItems": [
"1. 原点復帰を行う",
"2. 補給部ｼｬｯﾀｰの開閉を行い\u0022閉\u0022にする",
"1. 原点復帰を行う",
"2. 補給部ｼｬｯﾀｰの開閉を行い\u0022閉\u0022にする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"Inspectio... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.6㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"Inspectio... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.8㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"Insp... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"Inspectio... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"Inspectio... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.15㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸原点登録",
"WorkItems": [
"2. TP軸をﾊﾟﾜｰONする",
"3. TP軸原点登録",
"1. ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄを緩める",
"4. TP軸原点ｾﾝｻ調整"
],
"WorkPoints": [
"ﾊﾟﾜｰOFFでﾚﾊﾞｰを原点付近へ動かす",
"ﾚﾊﾞｰが原点を探し動き始め原点確認後停止する",
"ﾒｶｽﾄｯﾊﾟｰ端面",... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "引き出し部調整治具",
"Size": "",
"ToolOther": "FM-6646",
"WorkName": "TP軸原点登録",
"WorkItems": [
"3. TP軸原点登録",
"1. ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄを緩める",
"4. TP軸原点ｾﾝｻ調整"
],
"WorkPoints": [
"ﾚﾊﾞｰが原点を探し動き始め原点確認後停止する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6646",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付られている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TP軸原点登録",
"WorkItems": [],
"WorkPoints": [
"ﾒｶｽﾄｯﾊﾟｰ端面",
"㉖でTP軸を動作させ、原点から『0.9㎜』で投光、『1.0㎜』で遮光の位置でセンサ位置を調整する",
"プーリーの固定が完了したら、㉘を取り外し、㉖にて原点復帰の確認を行う",
"TP軸原点ｾﾝｻﾄﾞｸﾞ",
"ｾﾝｻ位置調整ﾎﾞﾙﾄ"
],
"Tolks": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸原点登録",
"WorkItems": [
"2. TP軸をﾊﾟﾜｰONする",
"3. TP軸原点登録",
"1. ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄを緩める",
"4. TP軸原点ｾﾝｻ調整"
],
"WorkPoints": [
"ﾊﾟﾜｰOFFでﾚﾊﾞｰを原点付近へ動かす",
"ﾚﾊﾞｰが原点を探し動き始め原点確認後停止する",
"ﾒｶｽﾄｯﾊﾟｰ端面",... | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが0.9㎜で投光1.0㎜で遮光する事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整①",
"WorkItems": [
"1. ﾊﾟﾜｰONする",
"2. TL軸原点復帰を行う",
"3. 引き出部を原点位置から下段23Slot高さへ移動する"
],
"WorkPoints": [
"画面上で①②③④のﾎﾞﾀﾝを順次押すとﾊﾟﾜｰONとなる",
"ﾊﾟﾜｰOFFでﾚﾊﾞｰを原点付近へ動かす",
"FM-2848治... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"4. 治具を取付ける",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5519",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す",
"4. 治具を取付ける"
],
"WorkPoints": [
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"FM-1934を引き出部へ",
"A0",
"A 1",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀﾞｲﾚｸﾄﾄﾚｲﾌｨｰﾀﾞJIG",
"Size": "",
"ToolOther": "FM-1934",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"4. 治具を取付ける",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1934",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "中央:±0.05㎜以内左右:±0.2㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.