input stringclasses 1 value | instruction stringlengths 181 1.31k | output stringlengths 329 1.48k | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"表示灯・ﾌﾞｻﾞｰ関連ﾁｪｯｸ","WorkItems":["1. ①をﾀｯﾁ","2. 状態変化の目視確認実施","3. 全項目にて目視確認実施後OKをﾀｯﾁ､全項目のOK表示を確認後､①をﾀｯﾁ"],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","ｼｸﾞﾅﾙﾀﾜｰ","F ﾊﾟｰﾂ切れﾗｲﾄ","R ﾊﾟｰﾂ切れﾗｲﾄ","FRONT","状態が正常ならば OK をﾀｯﾁ","初期状態OKで 橙→青に変化","OKﾀｯﾁで次項目に切替るので 状態が正常ならば 継続して確認する","最終状態は青","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"表示灯・ﾌﾞｻﾞｰ関連ﾁｪｯｸ","WorkItems":["1. ①をﾀｯﾁ","2. 状態変化の目視確認実施","3. 全項目にて目視確認実施後OKをﾀｯﾁ､全項目のOK表示を確認後､①をﾀｯﾁ"],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","ｼｸﾞﾅﾙﾀﾜｰ","F ﾊﾟｰﾂ切れﾗｲﾄ","R ﾊﾟｰﾂ切れﾗｲﾄ","FRONT","状態が正常ならば OK をﾀｯﾁ","初期状態OKで 橙→青に変化","OKﾀｯﾁで次項目に切替るので 状態が正常ならば 継続して確認する","最終状態は青","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"出力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"前側確認①","WorkItems":["3. 状態変化を手動にて実施","1. ①をﾀｯﾁ","4. 入力OKで下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ","2. 下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ","5. 状態変化の目視確認実施"],"WorkPoints":["FRONT"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","F START SW","F START SWを 画面変化する迄押す","状態が正常ならば OK をﾀｯﾁ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"前側確認①","WorkItems":["3. 状態変化を手動にて実施","1. ①をﾀｯﾁ","4. 入力OKで下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ","2. 下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ","5. 状態変化の目視確認実施"],"WorkPoints":["FRONT"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","F START SW","F START SWを 画面変化する迄押す","状態が正常ならば OK をﾀｯﾁ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"入出力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"前側確認②","WorkItems":["1. 状態変化を手動にて実施","3. 入力OKで下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ","2. 状態変化を手動にて実施","4. 状態変化の目視確認実施"],"WorkPoints":["FRONT"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["F1 EXCHANGE SW","F STOP SW","F STOP SWを 画面変化する迄押す","入力OKで次項目に切替る","F1 EXCHANGE SWを 画面変化する迄押す","状態が正常ならば OK をﾀｯﾁ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"前側確認②","WorkItems":["1. 状態変化を手動にて実施","3. 入力OKで下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ","2. 状態変化を手動にて実施","4. 状態変化の目視確認実施"],"WorkPoints":["FRONT"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["F1 EXCHANGE SW","F STOP SW","F STOP SWを 画面変化する迄押す","入力OKで次項目に切替る","F1 EXCHANGE SWを 画面変化する迄押す","状態が正常ならば OK をﾀｯﾁ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"入出力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"前側確認③","WorkItems":["2. 入力OKで下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ","1. 状態変化を手動にて実施","4. 状態変化を手動にて実施","3. 状態変化の目視確認実施"],"WorkPoints":["FRONT"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["F2 EXCHANGE SW","F ACTIVATION SW","F2 EXCHANGE SWを 画面変化する迄押す","状態が正常ならば OK をﾀｯﾁ","F ACTIVATION SWを 画面変化する迄押す","最終項目入力 OK で 次へ をﾀｯﾁ しなくても自動で2/3ﾍﾟｰｼﾞに移る","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"前側確認③","WorkItems":["2. 入力OKで下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ","1. 状態変化を手動にて実施","4. 状態変化を手動にて実施","3. 状態変化の目視確認実施"],"WorkPoints":["FRONT"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["F2 EXCHANGE SW","F ACTIVATION SW","F2 EXCHANGE SWを 画面変化する迄押す","状態が正常ならば OK をﾀｯﾁ","F ACTIVATION SWを 画面変化する迄押す","最終項目入力 OK で 次へ をﾀｯﾁ しなくても自動で2/3ﾍﾟｰｼﾞに移る","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"入出力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"前側確認④","WorkItems":["3. 状態変化を手動にて実施","1. 状態変化を手動にて実施","F 安全ｶﾊﾞｰを開ける","搬送開口部ｾﾝｻ(左)を画面変化する迄遮光 →OKで搬送開口部ｾﾝｻ(右)を画面変化する迄遮光","2. 状態変化を手動にて実施"],"WorkPoints":["FRONT","F 安全ｶﾊﾞｰ"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["非常停止 SW ON/OFF","F 非常停止 SW","安全ｶﾊﾞｰ 開","搬送開口部ｾﾝｻ","FRONT","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","切替り後､非常停止SW解除","入力OKで次項目に切替る","F 非常停止 SWを 画面変化する迄押す","入力OKで次項目に切替る","入力OKで次項目に切替る","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"前側確認④","WorkItems":["3. 状態変化を手動にて実施","1. 状態変化を手動にて実施","F 安全ｶﾊﾞｰを開ける","搬送開口部ｾﾝｻ(左)を画面変化する迄遮光 →OKで搬送開口部ｾﾝｻ(右)を画面変化する迄遮光","2. 状態変化を手動にて実施"],"WorkPoints":["FRONT","F 安全ｶﾊﾞｰ"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["非常停止 SW ON/OFF","F 非常停止 SW","安全ｶﾊﾞｰ 開","搬送開口部ｾﾝｻ","FRONT","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","切替り後､非常停止SW解除","入力OKで次項目に切替る","F 非常停止 SWを 画面変化する迄押す","入力OKで次項目に切替る","入力OKで次項目に切替る","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"前側確認⑤","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"前側確認⑤","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"前側確認⑥","WorkItems":["2. 最終項目入力OK確認後､①をﾀｯﾁ","1. 状態変化を手動にて実施"],"WorkPoints":["F2(右側)","F2(右側)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["1S3711P","FRONT","最終状態は青","1S3711ｺﾈｸﾀを 画面変化する迄抜く","切替り後､ｺﾈｸﾀを戻す","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"前側確認⑥","WorkItems":["2. 最終項目入力OK確認後､①をﾀｯﾁ","1. 状態変化を手動にて実施"],"WorkPoints":["F2(右側)","F2(右側)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["1S3711P","FRONT","最終状態は青","1S3711ｺﾈｸﾀを 画面変化する迄抜く","切替り後､ｺﾈｸﾀを戻す","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"F1(左側)交換台車対応ﾕﾆｯﾄ有無検出確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"F1(左側)交換台車対応ﾕﾆｯﾄ有無検出確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ILK及び台車ｼｮｰﾄｺﾈｸﾀ","Size":"","ToolOther":"FE-0319FM-2962","WorkName":"F1(左側)供給部ILK確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"ILK及び台車ｼｮｰﾄｺﾈｸﾀ","Size":"","ToolOther":"FE-0319FM-2962","WorkName":"F1(左側)供給部ILK確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"FE-0319FM-2962","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ILK及び台車ｼｮｰﾄｺﾈｸﾀ","Size":"","ToolOther":"FE-0319FM-2962","WorkName":"F2(右側)供給部ILK確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"ILK及び台車ｼｮｰﾄｺﾈｸﾀ","Size":"","ToolOther":"FE-0319FM-2962","WorkName":"F2(右側)供給部ILK確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"FE-0319FM-2962","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ILK及び台車ｼｮｰﾄｺﾈｸﾀ","Size":"","ToolOther":"FE-0319FM-2962","WorkName":"F1(左側)台車確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"ILK及び台車ｼｮｰﾄｺﾈｸﾀ","Size":"","ToolOther":"FE-0319FM-2962","WorkName":"F1(左側)台車確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入出力確認","ToolManageNo":"FE-0319FM-2962","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ILK及び台車ｼｮｰﾄｺﾈｸﾀ","Size":"","ToolOther":"FE-0319FM-2962","WorkName":"F2(右側)台車確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"ILK及び台車ｼｮｰﾄｺﾈｸﾀ","Size":"","ToolOther":"FE-0319FM-2962","WorkName":"F2(右側)台車確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入出力確認","ToolManageNo":"FE-0319FM-2962","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"Fﾁｪﾝｼﾞｬ入力確認","WorkItems":["2. ①をﾀｯﾁ","3. 状態変化を手動にて実施","4. 入力OK確認後､①をﾀｯﾁ","1. F側のﾉｽﾞﾙﾁｪﾝｼﾞｬを外す"],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","ﾚﾊﾞｰを左に 倒したまま外す","F ﾉｽﾞﾙﾁｪﾝｼﾞｬを元に戻し 画面変化するか確認する","最終状態は青","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"Fﾁｪﾝｼﾞｬ入力確認","WorkItems":["2. ①をﾀｯﾁ","3. 状態変化を手動にて実施","4. 入力OK確認後､①をﾀｯﾁ","1. F側のﾉｽﾞﾙﾁｪﾝｼﾞｬを外す"],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","ﾚﾊﾞｰを左に 倒したまま外す","F ﾉｽﾞﾙﾁｪﾝｼﾞｬを元に戻し 画面変化するか確認する","最終状態は青","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"Fﾁｪﾝｼﾞｬ出力確認","WorkItems":["このﾒｯｾｰｼﾞにて再初期状態確認中","上昇･下降動作の入力信号も自動検査する","開閉動作の入力信号も自動検査する","2. 状態変化の目視確認実施","3. 状態変化の目視確認実施","4. 全項目のOK表示確認後､①をﾀｯﾁ","5. Fﾁｪﾝｼﾞｬ出力迄の完了表示確認","1. ①をﾀｯﾁ","自動検査実行中","自動検査実行中"],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","自動で上昇･下降動作を行い検査する","自動で開閉動作を行い 検査する","最終状態は青","仕様無の項目は完了ﾒｯｾｰｼﾞは表示しない","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"Fﾁｪﾝｼﾞｬ出力確認","WorkItems":["このﾒｯｾｰｼﾞにて再初期状態確認中","上昇･下降動作の入力信号も自動検査する","開閉動作の入力信号も自動検査する","2. 状態変化の目視確認実施","3. 状態変化の目視確認実施","4. 全項目のOK表示確認後､①をﾀｯﾁ","5. Fﾁｪﾝｼﾞｬ出力迄の完了表示確認","1. ①をﾀｯﾁ","自動検査実行中","自動検査実行中"],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","自動で上昇･下降動作を行い検査する","自動で開閉動作を行い 検査する","最終状態は青","仕様無の項目は完了ﾒｯｾｰｼﾞは表示しない","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"出力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"搬送用基板240×216","Size":"","ToolOther":"","WorkName":"L1/L2搬送確認①","WorkItems":["初期動作実行中","1. L1/L2選択→①をﾀｯﾁ","2. ①をﾀｯﾁ","3. 下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ","4. 搬送用基板を投入","自動検査が始まる"],"WorkPoints":["※ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様時は1枚にて実施","※ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様時は L1 のみ選択","※画像はﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様時"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","基板投入","初期動実行作中にL1/2共に､基板幅が自動動作し､搬送基板ｻｲｽﾞに変更することを確認","低速にて搬送開始","実行中のﾒｯｾｰｼﾞが表示したら L1/2共に､搬送基板を投入する","※流れ仕様関係なく､左側から投入","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"搬送用基板240×216","Size":"","ToolOther":"","WorkName":"L1/L2搬送確認①","WorkItems":["初期動作実行中","1. L1/L2選択→①をﾀｯﾁ","2. ①をﾀｯﾁ","3. 下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ","4. 搬送用基板を投入","自動検査が始まる"],"WorkPoints":["※ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様時は1枚にて実施","※ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様時は L1 のみ選択","※画像はﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様時"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","基板投入","初期動実行作中にL1/2共に､基板幅が自動動作し､搬送基板ｻｲｽﾞに変更することを確認","低速にて搬送開始","実行中のﾒｯｾｰｼﾞが表示したら L1/2共に､搬送基板を投入する","※流れ仕様関係なく､左側から投入","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"入出力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"搬送用基板240×216","Size":"","ToolOther":"","WorkName":"L1/L2搬送確認②","WorkItems":["2. 全項目のOK表示確認後､基板を取除き①をﾀｯﾁ","3. 完了表示確認","1. 状態変化の確認","自動検査実行中","自動検査実行中","自動検査実行中","L1/2(♯1/2) 共に基板下受けが自動で上昇/下降することを目視確認","L1/2 基板検出ｾﾝｻ2 (右待機/右延長))検出後､ﾍﾞﾙﾄが 逆回転し､高速にて再び搬入位置に 基板が戻ってきて 終了"],"WorkPoints":["FRONT","ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様","ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様","※画像はﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様時","※ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様時は L1 のみ完了"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["基板検出ｾﾝｻ配置","実装位置#1","実装位置#2","ﾚｰﾝ1","ﾚｰﾝ1","ﾚｰﾝ2","実装位置#1","実装位置#2","実装位置#1","実装位置#2","右待機","左待機","右待機","左待機","最終状態は青","L1/2共に､自動検査OK後 次ﾍﾟｰｼﾞへ自動移行する","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"搬送用基板240×216","Size":"","ToolOther":"","WorkName":"L1/L2搬送確認②","WorkItems":["2. 全項目のOK表示確認後､基板を取除き①をﾀｯﾁ","3. 完了表示確認","1. 状態変化の確認","自動検査実行中","自動検査実行中","自動検査実行中","L1/2(♯1/2) 共に基板下受けが自動で上昇/下降することを目視確認","L1/2 基板検出ｾﾝｻ2 (右待機/右延長))検出後､ﾍﾞﾙﾄが 逆回転し､高速にて再び搬入位置に 基板が戻ってきて 終了"],"WorkPoints":["FRONT","ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様","ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様","※画像はﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様時","※ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様時は L1 のみ完了"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["基板検出ｾﾝｻ配置","実装位置#1","実装位置#2","ﾚｰﾝ1","ﾚｰﾝ1","ﾚｰﾝ2","実装位置#1","実装位置#2","実装位置#1","実装位置#2","右待機","左待機","右待機","左待機","最終状態は青","L1/2共に､自動検査OK後 次ﾍﾟｰｼﾞへ自動移行する","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"入出力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"SIG1/2確認","WorkItems":["1. SIG1/SIG2選択→①をﾀｯﾁ","2. ①をﾀｯﾁ","3. 状態変化の確認","4. 全項目のOK表示確認後､①をﾀｯﾁ","5. 完了表示確認","自動検査実行中","自動検査実行中","自動検査実行中"],"WorkPoints":["※画像はﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様時","※ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様時は SIG1 のみ選択","※ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様時は SIG1 のみ完了"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","SIG1/2共に､自動検査OK後 次ﾍﾟｰｼﾞへ自動移行する","最終状態は青","SIG1/2共に､自動検査OK後 次ﾍﾟｰｼﾞへ自動移行する","検査表①:I/O ﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"SIG1/2確認","WorkItems":["1. SIG1/SIG2選択→①をﾀｯﾁ","2. ①をﾀｯﾁ","3. 状態変化の確認","4. 全項目のOK表示確認後､①をﾀｯﾁ","5. 完了表示確認","自動検査実行中","自動検査実行中","自動検査実行中"],"WorkPoints":["※画像はﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様時","※ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様時は SIG1 のみ選択","※ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様時は SIG1 のみ完了"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","SIG1/2共に､自動検査OK後 次ﾍﾟｰｼﾞへ自動移行する","最終状態は青","SIG1/2共に､自動検査OK後 次ﾍﾟｰｼﾞへ自動移行する","検査表①:I/O ﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"入出力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"瞬停ﾘｾｯﾄ確認","WorkItems":["入力信号も自動検査する","1. 瞬停ﾘｾｯﾄ選択→①をﾀｯﾁ","2. ①をﾀｯﾁ","3. 状態変化の確認","5. 全項目のOK表示確認後､①をﾀｯﾁ","4. 状態変化の確認"],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","OKﾀｯﾁで次項目に切替る","最終状態は青","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"瞬停ﾘｾｯﾄ確認","WorkItems":["入力信号も自動検査する","1. 瞬停ﾘｾｯﾄ選択→①をﾀｯﾁ","2. ①をﾀｯﾁ","3. 状態変化の確認","5. 全項目のOK表示確認後､①をﾀｯﾁ","4. 状態変化の確認"],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","OKﾀｯﾁで次項目に切替る","最終状態は青","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"入出力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"後側確認①","WorkItems":["2. 下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ","1. ①をﾀｯﾁ","4. 状態変化を手動にて実施","5. 状態変化を手動にて実施","3. 状態変化の確認","確認済なので OK をﾀｯﾁ","6. SD-EJM2FH2-052-1に進む"],"WorkPoints":["REAR","FRONT"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","F ｻｰﾎﾞ SW","R START SW","変化で次項目に切替る","F ｻｰﾎﾞ SWをON→OFF 画面変化する迄OFFにする","変化後､ONに戻す","R START SWを 画面変化する迄押す","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"後側確認①","WorkItems":["2. 下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ","1. ①をﾀｯﾁ","4. 状態変化を手動にて実施","5. 状態変化を手動にて実施","3. 状態変化の確認","確認済なので OK をﾀｯﾁ","6. SD-EJM2FH2-052-1に進む"],"WorkPoints":["REAR","FRONT"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","F ｻｰﾎﾞ SW","R START SW","変化で次項目に切替る","F ｻｰﾎﾞ SWをON→OFF 画面変化する迄OFFにする","変化後､ONに戻す","R START SWを 画面変化する迄押す","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"後側確認②","WorkItems":["4. 状態変化を手動にて実施","2. 状態変化の目視確認実施","3. 状態変化を手動にて実施","5. 入力OKで下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ","6. 状態変化の目視確認実施","1. SD-EJM2FH2-051-6の続き:入力OKで下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ"],"WorkPoints":["REAR"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["R1 EXCHANGE SW","R STOP SW","状態が正常ならば OK をﾀｯﾁ","R STOP SWを 画面変化する迄押す","入力OKで次項目に切替る","R1 EXCHANGE SWを 画面変化する迄押す","状態が正常ならば OK をﾀｯﾁ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"後側確認②","WorkItems":["4. 状態変化を手動にて実施","2. 状態変化の目視確認実施","3. 状態変化を手動にて実施","5. 入力OKで下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ","6. 状態変化の目視確認実施","1. SD-EJM2FH2-051-6の続き:入力OKで下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ"],"WorkPoints":["REAR"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["R1 EXCHANGE SW","R STOP SW","状態が正常ならば OK をﾀｯﾁ","R STOP SWを 画面変化する迄押す","入力OKで次項目に切替る","R1 EXCHANGE SWを 画面変化する迄押す","状態が正常ならば OK をﾀｯﾁ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"入出力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"後側確認③","WorkItems":["1. 状態変化を手動にて実施","2. 入力OKで下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ","3. 状態変化の目視確認実施","4. 状態変化を手動にて実施"],"WorkPoints":["REAR"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["R2 EXCHANGE SW","最終項目入力 OK で 次へ をﾀｯﾁ しなくても自動で2/4ﾍﾟｰｼﾞに移る","R2 EXCHANGE SWを 画面変化する迄押す","状態が正常ならば OK をﾀｯﾁ","F ACTIVATION SWを 画面変化する迄押す","入力OKで次項目に切替る","R ACTIVATION SW","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"後側確認③","WorkItems":["1. 状態変化を手動にて実施","2. 入力OKで下記ﾒｯｾｰｼﾞを表示するので①をﾀｯﾁ","3. 状態変化の目視確認実施","4. 状態変化を手動にて実施"],"WorkPoints":["REAR"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["R2 EXCHANGE SW","最終項目入力 OK で 次へ をﾀｯﾁ しなくても自動で2/4ﾍﾟｰｼﾞに移る","R2 EXCHANGE SWを 画面変化する迄押す","状態が正常ならば OK をﾀｯﾁ","F ACTIVATION SWを 画面変化する迄押す","入力OKで次項目に切替る","R ACTIVATION SW","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"入出力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"後側確認④","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"後側確認④","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"後側確認⑤","WorkItems":["1. 状態変化を手動にて実施","2. 状態変化を手動にて実施"],"WorkPoints":["R2(右側)","R2(右側)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:I/Oﾁｪｯｸﾘｽﾄ","取外し","廃棄BOX","取付け","R側 廃棄BOXを 画面変化する迄外す","切替り後､廃棄BOX戻す","入力OKで次項目に切替る","REAR","1S3715P","1S3715ｺﾈｸﾀを 画面変化する迄抜く","切替り後､ｺﾈｸﾀを戻す","入力OKで次項目に切替る","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"後側確認⑤","WorkItems":["1. 状態変化を手動にて実施","2. 状態変化を手動にて実施"],"WorkPoints":["R2(右側)","R2(右側)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:I/Oﾁｪｯｸﾘｽﾄ","取外し","廃棄BOX","取付け","R側 廃棄BOXを 画面変化する迄外す","切替り後､廃棄BOX戻す","入力OKで次項目に切替る","REAR","1S3715P","1S3715ｺﾈｸﾀを 画面変化する迄抜く","切替り後､ｺﾈｸﾀを戻す","入力OKで次項目に切替る","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"後側確認⑥","WorkItems":["1. 状態変化を手動にて実施","2. 状態変化を手動にて実施","5. 状態変化を手動にて実施","6. 状態変化を手動にて実施","3. 状態変化を手動にて実施","4. 状態変化を手動にて実施"],"WorkPoints":["※左からFAN A/B/C/D/E/F"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["FAN A","FAN B","FAN C","FAN D","FAN E","FAN F","↓箇所のｺﾈｸﾀを抜差し","SIO(K311) 基板","入力OKで次項目に切替る","切替り後､ｺﾈｸﾀを差す","SIO基板ｺﾈｸﾀ FANA K311を 画面変化する迄抜いておく","SIO基板ｺﾈｸﾀ FANB K311を 画面変化する迄抜いておく","入力OKで次項目に切替る","切替り後､ｺﾈｸﾀを差す","SIO基板ｺﾈｸﾀ FANC K311を 画面変化する迄抜いておく","入力OKで次項目に切替る","切替り後､ｺﾈｸﾀを差す","SIO基板ｺﾈｸﾀ FAND K311を 画面変化する迄抜いておく","入力OKで次項目に切替る","切替り後､ｺﾈｸﾀを差す","SIO基板ｺﾈｸﾀ FANE K311を 画面変化する迄抜いておく","入力OKで次項目に切替る","切替り後､ｺﾈｸﾀを差す","SIO基板ｺﾈｸﾀ FANF K311を 画面変化する迄抜いておく","切替り後､ｺﾈｸﾀを差す","最終項目入力 OK で 次へ をﾀｯﾁ しなくても自動で4/4ﾍﾟｰｼﾞに移る","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"後側確認⑥","WorkItems":["1. 状態変化を手動にて実施","2. 状態変化を手動にて実施","5. 状態変化を手動にて実施","6. 状態変化を手動にて実施","3. 状態変化を手動にて実施","4. 状態変化を手動にて実施"],"WorkPoints":["※左からFAN A/B/C/D/E/F"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["FAN A","FAN B","FAN C","FAN D","FAN E","FAN F","↓箇所のｺﾈｸﾀを抜差し","SIO(K311) 基板","入力OKで次項目に切替る","切替り後､ｺﾈｸﾀを差す","SIO基板ｺﾈｸﾀ FANA K311を 画面変化する迄抜いておく","SIO基板ｺﾈｸﾀ FANB K311を 画面変化する迄抜いておく","入力OKで次項目に切替る","切替り後､ｺﾈｸﾀを差す","SIO基板ｺﾈｸﾀ FANC K311を 画面変化する迄抜いておく","入力OKで次項目に切替る","切替り後､ｺﾈｸﾀを差す","SIO基板ｺﾈｸﾀ FAND K311を 画面変化する迄抜いておく","入力OKで次項目に切替る","切替り後､ｺﾈｸﾀを差す","SIO基板ｺﾈｸﾀ FANE K311を 画面変化する迄抜いておく","入力OKで次項目に切替る","切替り後､ｺﾈｸﾀを差す","SIO基板ｺﾈｸﾀ FANF K311を 画面変化する迄抜いておく","切替り後､ｺﾈｸﾀを差す","最終項目入力 OK で 次へ をﾀｯﾁ しなくても自動で4/4ﾍﾟｰｼﾞに移る","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"後側確認⑦","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"後側確認⑦","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"後側確認⑧","WorkItems":["1. 状態変化を手動にて実施","2. 最終項目入力OK確認後､①をﾀｯﾁ"],"WorkPoints":["REAR"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["R ｻｰﾎﾞ SW","R ｻｰﾎﾞ SWをON→OFF 画面変化する迄OFFにする","変化後､ONに戻す","最終状態は青","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"後側確認⑧","WorkItems":["1. 状態変化を手動にて実施","2. 最終項目入力OK確認後､①をﾀｯﾁ"],"WorkPoints":["REAR"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["R ｻｰﾎﾞ SW","R ｻｰﾎﾞ SWをON→OFF 画面変化する迄OFFにする","変化後､ONに戻す","最終状態は青","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"R1(左側)交換台車対応ﾕﾆｯﾄ有無検出確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"R1(左側)交換台車対応ﾕﾆｯﾄ有無検出確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ILK及び台車ｼｮｰﾄｺﾈｸﾀ","Size":"","ToolOther":"FE-0319FM-2962","WorkName":"R1(左側)供給部ILK確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"ILK及び台車ｼｮｰﾄｺﾈｸﾀ","Size":"","ToolOther":"FE-0319FM-2962","WorkName":"R1(左側)供給部ILK確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"FE-0319FM-2962","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ILK及び台車ｼｮｰﾄｺﾈｸﾀ","Size":"","ToolOther":"FE-0319FM-2962","WorkName":"R2(右側)供給部ILK確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"ILK及び台車ｼｮｰﾄｺﾈｸﾀ","Size":"","ToolOther":"FE-0319FM-2962","WorkName":"R2(右側)供給部ILK確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"FE-0319FM-2962","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ILK及び台車ｼｮｰﾄｺﾈｸﾀ","Size":"","ToolOther":"FE-0319FM-2962","WorkName":"R1(左側)台車確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"ILK及び台車ｼｮｰﾄｺﾈｸﾀ","Size":"","ToolOther":"FE-0319FM-2962","WorkName":"R1(左側)台車確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入出力確認","ToolManageNo":"FE-0319FM-2962","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ILK及び台車ｼｮｰﾄｺﾈｸﾀ","Size":"","ToolOther":"FE-0319FM-2962","WorkName":"R2(右側)台車確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"ILK及び台車ｼｮｰﾄｺﾈｸﾀ","Size":"","ToolOther":"FE-0319FM-2962","WorkName":"R2(右側)台車確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入出力確認","ToolManageNo":"FE-0319FM-2962","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"Rﾁｪﾝｼﾞｬ入力確認","WorkItems":["2. ①をﾀｯﾁ","3. 状態変化を手動にて実施","4. 入力OK確認後､①をﾀｯﾁ","1. F側のﾉｽﾞﾙﾁｪﾝｼﾞｬを外す"],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","ﾚﾊﾞｰを左に 倒したまま外す","検査表①:I/Oﾁｪｯｸﾘｽﾄ","F ﾉｽﾞﾙﾁｪﾝｼﾞｬを元に戻し 画面変化するか確認する","最終状態は青","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"Rﾁｪﾝｼﾞｬ入力確認","WorkItems":["2. ①をﾀｯﾁ","3. 状態変化を手動にて実施","4. 入力OK確認後､①をﾀｯﾁ","1. F側のﾉｽﾞﾙﾁｪﾝｼﾞｬを外す"],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","ﾚﾊﾞｰを左に 倒したまま外す","検査表①:I/Oﾁｪｯｸﾘｽﾄ","F ﾉｽﾞﾙﾁｪﾝｼﾞｬを元に戻し 画面変化するか確認する","最終状態は青","WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"Rﾁｪﾝｼﾞｬ出力確認","WorkItems":["2. 状態変化の目視確認実施","3. 状態変化の目視確認実施","4. 全項目のOK表示確認後､①をﾀｯﾁ","5. 全ての完了表示確認後､①をﾀｯﾁ","1. ①をﾀｯﾁ","上昇･下降動作の入力信号も自動検査する","このﾒｯｾｰｼﾞにて再初期状態確認中","開閉動作の入力信号も自動検査する","自動検査実行中","自動検査実行中"],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","自動で上昇･下降動作を行い検査する","自動で開閉動作を行い 検査する","最終状態は青","仕様無の項目は完了ﾒｯｾｰｼﾞは表示しない","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"Rﾁｪﾝｼﾞｬ出力確認","WorkItems":["2. 状態変化の目視確認実施","3. 状態変化の目視確認実施","4. 全項目のOK表示確認後､①をﾀｯﾁ","5. 全ての完了表示確認後､①をﾀｯﾁ","1. ①をﾀｯﾁ","上昇･下降動作の入力信号も自動検査する","このﾒｯｾｰｼﾞにて再初期状態確認中","開閉動作の入力信号も自動検査する","自動検査実行中","自動検査実行中"],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["初期状態ﾁｪｯｸ中","自動で上昇･下降動作を行い検査する","自動で開閉動作を行い 検査する","最終状態は青","仕様無の項目は完了ﾒｯｾｰｼﾞは表示しない","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"出力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸｾｯﾄｱｯﾌﾟ用SD","Size":"","ToolOther":"","WorkName":"標準ｼｽﾃﾑｱｯﾌﾟﾃﾞｰﾄ","WorkItems":["2. ｲﾝｽﾄｰﾙ完了後､画面指示に従い設備を再起動する","1. 標準ｼｽﾃﾑをｲﾝｽﾄｰﾙする"],"WorkPoints":["㉖を挿入後 《ﾛｸﾞｵﾝ》 を押す","ｻｰﾋﾞｽｴﾝｼﾞﾆｱに切り替える","㉗を挿入後 《SD》 を押す"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["最後にRS-232Cｹｰﾌﾞﾙ､ REX-BT60､連結ｹｰﾌﾞﾙを外す","① 《ｼｽﾃﾑ》 を選択","押す","② 《Update》 を押す","《はい》 を押す","押す","ｻｰﾋﾞｽｴﾝｼﾞﾆｱにて操作","ｽｸﾛｰﾙして 《設定》 を選択","② 《ｿﾌﾄｱｯﾌﾟﾃﾞｰﾄ》 を選択","③ 《ｱｯﾌﾟﾃﾞｰﾄ》 を選択","① 《SC》 を選択"]} | {"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸｾｯﾄｱｯﾌﾟ用SD","Size":"","ToolOther":"","WorkName":"標準ｼｽﾃﾑｱｯﾌﾟﾃﾞｰﾄ","WorkItems":["2. ｲﾝｽﾄｰﾙ完了後､画面指示に従い設備を再起動する","1. 標準ｼｽﾃﾑをｲﾝｽﾄｰﾙする"],"WorkPoints":["㉖を挿入後 《ﾛｸﾞｵﾝ》 を押す","ｻｰﾋﾞｽｴﾝｼﾞﾆｱに切り替える","㉗を挿入後 《SD》 を押す"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["最後にRS-232Cｹｰﾌﾞﾙ､ REX-BT60､連結ｹｰﾌﾞﾙを外す","① 《ｼｽﾃﾑ》 を選択","押す","② 《Update》 を押す","《はい》 を押す","押す","ｻｰﾋﾞｽｴﾝｼﾞﾆｱにて操作","ｽｸﾛｰﾙして 《設定》 を選択","② 《ｿﾌﾄｱｯﾌﾟﾃﾞｰﾄ》 を選択","③ 《ｱｯﾌﾟﾃﾞｰﾄ》 を選択","① 《SC》 を選択"],"QualityItem":"ｱｯﾌﾟﾃﾞｰﾄ確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通りｱｯﾌﾟﾃﾞｰﾄする事","Method":"目視","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸｶｯﾀｰ部開口確認治具","Size":"","ToolOther":"FM-3226","WorkName":"F1ﾃｰﾌﾟｶｯﾀ(17･34連台車仕様)","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸｶｯﾀｰ部開口確認治具","Size":"","ToolOther":"FM-3226","WorkName":"F1ﾃｰﾌﾟｶｯﾀ(17･34連台車仕様)","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"出力確認","ToolManageNo":"FM-3226","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"ｶｯﾀｰ部開口確認治具","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｶｯﾀｰ部開口確認治具","Size":"","ToolOther":"FM-3226","WorkName":"F2ﾃｰﾌﾟｶｯﾀ(17･34連台車仕様)","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"ｶｯﾀｰ部開口確認治具","Size":"","ToolOther":"FM-3226","WorkName":"F2ﾃｰﾌﾟｶｯﾀ(17･34連台車仕様)","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"出力確認","ToolManageNo":"FM-3226","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"ｶｯﾀｰ部開口確認治具","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸｶｯﾀｰ部開口確認治具","Size":"","ToolOther":"FM-3226","WorkName":"Fﾃｰﾌﾟｶｯﾀｰ①(30･60連台車仕様)","WorkItems":["2. 台車を挿入する","1. ｼｮｰﾄｺﾈｸﾀを外す","3. 操作ﾊﾟﾈﾙ左の 《EXCHANGE》 を長押しし､台車を接続する","7. 台車に治具を挿入し､下記状態になることを確認する","4. ㉖を挿入し、サービスエンジニアに切替える","6. を押しながら入出力画面ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ1をONにする","5. 番号順に選択しｱﾄﾞﾚｽ表示させる"],"WorkPoints":["入替","① 《全体》 を選択","③ 《ch2》 を選択","④ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ1を表示させる","写真は30連台車","写真は30連台車","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["F1 EXCHANGE SW","② 《入出力確認》 を選択","ｽｸﾛ❘ﾙ","ｻｰﾋﾞｽｴﾝｼﾞﾆｱにて操作","ｽｸﾛｰﾙして 《設定》 を選択","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸｶｯﾀｰ部開口確認治具","Size":"","ToolOther":"FM-3226","WorkName":"Fﾃｰﾌﾟｶｯﾀｰ①(30･60連台車仕様)","WorkItems":["2. 台車を挿入する","1. ｼｮｰﾄｺﾈｸﾀを外す","3. 操作ﾊﾟﾈﾙ左の 《EXCHANGE》 を長押しし､台車を接続する","7. 台車に治具を挿入し､下記状態になることを確認する","4. ㉖を挿入し、サービスエンジニアに切替える","6. を押しながら入出力画面ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ1をONにする","5. 番号順に選択しｱﾄﾞﾚｽ表示させる"],"WorkPoints":["入替","① 《全体》 を選択","③ 《ch2》 を選択","④ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ1を表示させる","写真は30連台車","写真は30連台車","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["F1 EXCHANGE SW","② 《入出力確認》 を選択","ｽｸﾛ❘ﾙ","ｻｰﾋﾞｽｴﾝｼﾞﾆｱにて操作","ｽｸﾛｰﾙして 《設定》 を選択","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"出力確認","ToolManageNo":"FM-3226","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"ｶｯﾀｰ部開口確認治具","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｶｯﾀｰ部開口確認治具","Size":"","ToolOther":"FM-3226","WorkName":"Fﾃｰﾌﾟｶｯﾀｰ②(30･60連台車仕様)","WorkItems":["4. を押しながら入出力画面ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ1をOFFにする","3. 台車に治具を挿入し､下記状態になることを確認する","1. ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ1はON状態のままｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ1を表示させる","2. を押しながら入出力画面ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ1をONにする","6. 台車に治具を挿入し､下記状態になることを確認する","5. を押しながら入出力画面ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ1をOFFにする"],"WorkPoints":["① 《ch7》 を選択","②ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ1を表示させる","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと","《ch7》 を選択","《ch2》 を選択","写真は30連台車","写真は30連台車","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["ｽｸﾛ❘ﾙ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"ｶｯﾀｰ部開口確認治具","Size":"","ToolOther":"FM-3226","WorkName":"Fﾃｰﾌﾟｶｯﾀｰ②(30･60連台車仕様)","WorkItems":["4. を押しながら入出力画面ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ1をOFFにする","3. 台車に治具を挿入し､下記状態になることを確認する","1. ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ1はON状態のままｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ1を表示させる","2. を押しながら入出力画面ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ1をONにする","6. 台車に治具を挿入し､下記状態になることを確認する","5. を押しながら入出力画面ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ1をOFFにする"],"WorkPoints":["① 《ch7》 を選択","②ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ1を表示させる","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと","《ch7》 を選択","《ch2》 を選択","写真は30連台車","写真は30連台車","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["ｽｸﾛ❘ﾙ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"出力確認","ToolManageNo":"FM-3226","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"ｶｯﾀｰ部開口確認治具","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｶｯﾀｰ部開口確認治具","Size":"","ToolOther":"FM-3226","WorkName":"R1ﾃｰﾌﾟｶｯﾀ(17･34連台車仕様)","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"ｶｯﾀｰ部開口確認治具","Size":"","ToolOther":"FM-3226","WorkName":"R1ﾃｰﾌﾟｶｯﾀ(17･34連台車仕様)","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"出力確認","ToolManageNo":"FM-3226","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"ｶｯﾀｰ部開口確認治具","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｶｯﾀｰ部開口確認治具","Size":"","ToolOther":"FM-3226","WorkName":"R2ﾃｰﾌﾟｶｯﾀ(17･34連台車仕様)","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"ｶｯﾀｰ部開口確認治具","Size":"","ToolOther":"FM-3226","WorkName":"R2ﾃｰﾌﾟｶｯﾀ(17･34連台車仕様)","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"出力確認","ToolManageNo":"FM-3226","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"ｶｯﾀｰ部開口確認治具","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｶｯﾀｰ部開口確認治具","Size":"","ToolOther":"FM-3226","WorkName":"Rﾃｰﾌﾟｶｯﾀｰ①(30･60連台車仕様)","WorkItems":["2. 台車を挿入する","1. ｼｮｰﾄｺﾈｸﾀを外す","3. 操作ﾊﾟﾈﾙ左の 《EXCHANGE》 を長押しし､台車を接続する","5. を押しながら入出力画面ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ5をONにする","6. 台車に治具を挿入し､下記状態になることを確認する","4. 番号順に選択しｱﾄﾞﾚｽ表示させる"],"WorkPoints":["① 《ch2》 を選択","②ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ5を表示させる","写真は30連台車","写真は30連台車","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["R1 EXCHANGE SW","ｽｸﾛ❘ﾙ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"ｶｯﾀｰ部開口確認治具","Size":"","ToolOther":"FM-3226","WorkName":"Rﾃｰﾌﾟｶｯﾀｰ①(30･60連台車仕様)","WorkItems":["2. 台車を挿入する","1. ｼｮｰﾄｺﾈｸﾀを外す","3. 操作ﾊﾟﾈﾙ左の 《EXCHANGE》 を長押しし､台車を接続する","5. を押しながら入出力画面ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ5をONにする","6. 台車に治具を挿入し､下記状態になることを確認する","4. 番号順に選択しｱﾄﾞﾚｽ表示させる"],"WorkPoints":["① 《ch2》 を選択","②ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ5を表示させる","写真は30連台車","写真は30連台車","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["R1 EXCHANGE SW","ｽｸﾛ❘ﾙ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"出力確認","ToolManageNo":"FM-3226","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"ｶｯﾀｰ部開口確認治具","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｶｯﾀｰ部開口確認治具","Size":"","ToolOther":"FM-3226","WorkName":"Rﾃｰﾌﾟｶｯﾀｰ②(30･60連台車仕様)","WorkItems":["4. を押しながら入出力画面ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ5をOFFにする","5. を押しながら入出力画面ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ5をOFFにする","1. ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ5はON状態のままｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ5を表示させる","2. を押しながら入出力画面ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ5をONにする","4. を押しながら入出力画面ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ5をOFFにする","5. を押しながら入出力画面ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ5をOFFにする","1. ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ5はON状態のままｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ5を表示させる","2. を押しながら入出力画面ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ5をONにする"],"WorkPoints":["① 《ch7》 を選択","②ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ5を表示させる","《ch2》 を選択","《ch7》 を選択","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと","① 《ch7》 を選択","②ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ5を表示させる","《ch2》 を選択","《ch7》 を選択","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["ｽｸﾛ❘ﾙ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","ｽｸﾛ❘ﾙ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"ｶｯﾀｰ部開口確認治具","Size":"","ToolOther":"FM-3226","WorkName":"Rﾃｰﾌﾟｶｯﾀｰ②(30･60連台車仕様)","WorkItems":["4. を押しながら入出力画面ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ5をOFFにする","5. を押しながら入出力画面ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ5をOFFにする","1. ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ5はON状態のままｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ5を表示させる","2. を押しながら入出力画面ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ5をONにする","4. を押しながら入出力画面ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ5をOFFにする","5. を押しながら入出力画面ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ5をOFFにする","1. ｱﾄﾞﾚｽ00A0 ﾋﾞｯﾄ5はON状態のままｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ5を表示させる","2. を押しながら入出力画面ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ5をONにする"],"WorkPoints":["① 《ch7》 を選択","②ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ5を表示させる","《ch2》 を選択","《ch7》 を選択","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと","① 《ch7》 を選択","②ｱﾄﾞﾚｽ01E0 ﾋﾞｯﾄ5を表示させる","《ch2》 を選択","《ch7》 を選択","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと","※出力操作時はｶｯﾀｰ部開口確認治具を挿入しないこと"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["ｽｸﾛ❘ﾙ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","ｽｸﾛ❘ﾙ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","WETE-G002-B02"],"QualityItem":"出力確認","ToolManageNo":"FM-3226","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"ｶｯﾀｰ部開口確認治具","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾗｲﾝSWBOX","Size":"","ToolOther":"FM-2460","WorkName":"隣接装置安全入力確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"ﾗｲﾝSWBOX","Size":"","ToolOther":"FM-2460","WorkName":"隣接装置安全入力確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"FM-2460","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り確認する事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"基板ﾎﾙﾀﾞ高さ検出ｾﾝｻ動作確認治具","Size":"","ToolOther":"FM-6723","WorkName":"基板ﾎﾙﾀﾞ位置検出①","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"基板ﾎﾙﾀﾞ高さ検出ｾﾝｻ動作確認治具","Size":"","ToolOther":"FM-6723","WorkName":"基板ﾎﾙﾀﾞ位置検出①","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"FM-6723","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り確認する事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"基板ﾎﾙﾀﾞ高さ検出ｾﾝｻ動作確認治具","Size":"","ToolOther":"FM-6723","WorkName":"基板ﾎﾙﾀﾞ位置検出②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"基板ﾎﾙﾀﾞ高さ検出ｾﾝｻ動作確認治具","Size":"","ToolOther":"FM-6723","WorkName":"基板ﾎﾙﾀﾞ位置検出②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"FM-6723","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り確認する事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"真空ﾎﾟﾝﾌﾟ冷却ﾌｧﾝ回転ﾊﾟﾙｽ","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"真空ﾎﾟﾝﾌﾟ冷却ﾌｧﾝ回転ﾊﾟﾙｽ","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り確認する事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸｼﾘﾝﾀﾞﾛｯﾄﾞ戻り防止治具","Size":"","ToolOther":"FM-6751","WorkName":"L1/L2(L/R)搬送ﾚｰﾙｸﾗﾝﾌﾟ解除検出(ｵﾌﾟｼｮﾝ:延長ｺﾝﾍﾞｱ)①","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸｼﾘﾝﾀﾞﾛｯﾄﾞ戻り防止治具","Size":"","ToolOther":"FM-6751","WorkName":"L1/L2(L/R)搬送ﾚｰﾙｸﾗﾝﾌﾟ解除検出(ｵﾌﾟｼｮﾝ:延長ｺﾝﾍﾞｱ)①","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入出力確認","ToolManageNo":"FM-6751","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り確認する事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｼﾘﾝﾀﾞﾛｯﾄﾞ戻り防止治具","Size":"","ToolOther":"FM-6751","WorkName":"L1/L2(L/R)搬送ﾚｰﾙｸﾗﾝﾌﾟ解除検出(ｵﾌﾟｼｮﾝ:延長ｺﾝﾍﾞｱ)②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"ｼﾘﾝﾀﾞﾛｯﾄﾞ戻り防止治具","Size":"","ToolOther":"FM-6751","WorkName":"L1/L2(L/R)搬送ﾚｰﾙｸﾗﾝﾌﾟ解除検出(ｵﾌﾟｼｮﾝ:延長ｺﾝﾍﾞｱ)②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入出力確認","ToolManageNo":"FM-6751","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り確認する事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸ基板検出ｾﾝｻ遮光治具","Size":"","ToolOther":"FM-3324","WorkName":"L1/L2基板検出ｾﾝｻ1･2(実装位置♯2)(ｵﾌﾟｼｮﾝ:ｽﾗｲﾄﾞ搬送)","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸ基板検出ｾﾝｻ遮光治具","Size":"","ToolOther":"FM-3324","WorkName":"L1/L2基板検出ｾﾝｻ1･2(実装位置♯2)(ｵﾌﾟｼｮﾝ:ｽﾗｲﾄﾞ搬送)","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"FM-3324","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り確認する事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸ","Size":"","ToolOther":"","WorkName":"F1/R1ﾌｨｰﾀﾞ安全ｶﾊﾞｰSW(台車ﾄﾞｯｸﾞ識別bit2)(ｵﾌﾟｼｮﾝ:切替仕様)","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸ","Size":"","ToolOther":"","WorkName":"F1/R1ﾌｨｰﾀﾞ安全ｶﾊﾞｰSW(台車ﾄﾞｯｸﾞ識別bit2)(ｵﾌﾟｼｮﾝ:切替仕様)","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り確認する事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"F1/R1ﾄﾚｲ/台車切替ﾕﾆｯﾄ有無(ｵﾌﾟｼｮﾝ:切替仕様)","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"F1/R1ﾄﾚｲ/台車切替ﾕﾆｯﾄ有無(ｵﾌﾟｼｮﾝ:切替仕様)","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り確認する事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸ","Size":"","ToolOther":"","WorkName":"ﾋﾞｰﾑ干渉ｾﾝｻ確認","WorkItems":["5. F/Rのﾋﾞｰﾑを干渉させる","6. 入出力画面ｱﾄﾞﾚｽ2C51 ﾋﾞｯﾄ4がOFFになることを確認する","1. ㉖を挿入し、サービスエンジニアに切替える","3. F/Rのﾋﾞｰﾑを干渉位置から離す","4. 入出力画面ｱﾄﾞﾚｽ2C51 ﾋﾞｯﾄ4がONになることを確認する","2. 番号順に選択しｱﾄﾞﾚｽ表示させる"],"WorkPoints":["① 《全体》 を選択","④ 《ch1》 を選択","⑤ｱﾄﾞﾚｽ2C51 ﾋﾞｯﾄ4を表示させる","ｾﾝｻとﾄﾞｸﾞを離す","ｾﾝｻを遮光する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["② 《入出力確認》 を選択","③ 《ﾍｯﾄﾞ通信IO》 を選択","ｽｸﾛ❘ﾙ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","ｻｰﾋﾞｽｴﾝｼﾞﾆｱにて操作","ｽｸﾛｰﾙして 《設定》 を選択","WETE-G002-B02"]} | {"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸ","Size":"","ToolOther":"","WorkName":"ﾋﾞｰﾑ干渉ｾﾝｻ確認","WorkItems":["5. F/Rのﾋﾞｰﾑを干渉させる","6. 入出力画面ｱﾄﾞﾚｽ2C51 ﾋﾞｯﾄ4がOFFになることを確認する","1. ㉖を挿入し、サービスエンジニアに切替える","3. F/Rのﾋﾞｰﾑを干渉位置から離す","4. 入出力画面ｱﾄﾞﾚｽ2C51 ﾋﾞｯﾄ4がONになることを確認する","2. 番号順に選択しｱﾄﾞﾚｽ表示させる"],"WorkPoints":["① 《全体》 を選択","④ 《ch1》 を選択","⑤ｱﾄﾞﾚｽ2C51 ﾋﾞｯﾄ4を表示させる","ｾﾝｻとﾄﾞｸﾞを離す","ｾﾝｻを遮光する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["② 《入出力確認》 を選択","③ 《ﾍｯﾄﾞ通信IO》 を選択","ｽｸﾛ❘ﾙ","検査表①:I/Oﾁｪｯｸﾘｽﾄ","ｻｰﾋﾞｽｴﾝｼﾞﾆｱにて操作","ｽｸﾛｰﾙして 《設定》 を選択","WETE-G002-B02"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り確認する事","Method":"目視","RecordMethod":"WETE-G002-B02","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"搬送流れ方向識別確認","WorkItems":["6. 設備電源をOFFする","1. 設備電源をONし､入出力確認画面にてｱﾄﾞﾚｽ0044 ﾋﾞｯﾄ2･3の 《搬送流れ方向識別》 が仕様通りになっているか確認する","2. 設備電源をOFFする","3. ﾊﾟﾜｰﾕﾆｯﾄのSIO基板のｺﾈｸﾀを入替える","4. 設備の電源をONする","5. 入出力確認画面ｱﾄﾞﾚｽ0044 ﾋﾞｯﾄ2･3の 《搬送流れ方向識別》 が逆になっているか確認する","7. 入替えたｺﾈｸﾀを仕様通りに接続する"],"WorkPoints":["正流れ仕様時 上:CNDU-P_K311(L→R) ⇒ CNDU-P_K311(R→L) 下:CNDU-S_K311(L→R) ⇒ CNDU-S_K311(R→L)","逆流れ仕様時 上:CNDU-P_K311(R→L) ⇒ CNDU-P_K311(L→R) 下:CNDU-S_K311(R→L) ⇒ CDU-S_K311(L→R)","逆流れ仕様時 上:CN00_K311(R→L) ⇒ CN00_K311(L→R) 下:CN01_K311(R→L) ⇒ CN01_K311(L→R)","正流れ仕様時 上:CN00_K311(L→R) ⇒ CN00_K311(R→L) 下:CN01_K311(L→R) ⇒ CN01_K311(R→L)","※本検査は仕様通りの搬送ﾓｰﾀ動作確認終了後に行うこと","ｺﾈｸﾀを確実に差込むこと","正流れ時は接続ｺﾈｸﾀ側① (左) ､逆流れ時② (右) のﾏｰｷﾝｸﾞﾀｲ名称に従ってｺﾈｸﾀを接続すること","左→右(正流れ)仕様時:ON","①本体→②入出力確認→③ﾘﾝｸ→④ch1→⑤ｱﾄﾞﾚｽ0044 ﾋﾞｯﾄ2･3を表示","右→左(逆流れ)仕様時:OFF","左→右(正流れ)仕様時､ｺﾈｸﾀ入替え後:OFF","右→左(逆流れ)仕様時､ｺﾈｸﾀ入替え後:ON"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:4.Sysytem ON時動作確認 (3/3) (6) 搬送流れ方向識別確認","検査表①:4.Sysytem ON時動作確認 (3/3) (6) 搬送流れ方向識別確認","検査表①:4.Sysytem ON時動作確認 (3/3) (6) 搬送流れ方向識別確認","WETE-G002-B01"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"搬送流れ方向識別確認","WorkItems":["6. 設備電源をOFFする","1. 設備電源をONし､入出力確認画面にてｱﾄﾞﾚｽ0044 ﾋﾞｯﾄ2･3の 《搬送流れ方向識別》 が仕様通りになっているか確認する","2. 設備電源をOFFする","3. ﾊﾟﾜｰﾕﾆｯﾄのSIO基板のｺﾈｸﾀを入替える","4. 設備の電源をONする","5. 入出力確認画面ｱﾄﾞﾚｽ0044 ﾋﾞｯﾄ2･3の 《搬送流れ方向識別》 が逆になっているか確認する","7. 入替えたｺﾈｸﾀを仕様通りに接続する"],"WorkPoints":["正流れ仕様時 上:CNDU-P_K311(L→R) ⇒ CNDU-P_K311(R→L) 下:CNDU-S_K311(L→R) ⇒ CNDU-S_K311(R→L)","逆流れ仕様時 上:CNDU-P_K311(R→L) ⇒ CNDU-P_K311(L→R) 下:CNDU-S_K311(R→L) ⇒ CDU-S_K311(L→R)","逆流れ仕様時 上:CN00_K311(R→L) ⇒ CN00_K311(L→R) 下:CN01_K311(R→L) ⇒ CN01_K311(L→R)","正流れ仕様時 上:CN00_K311(L→R) ⇒ CN00_K311(R→L) 下:CN01_K311(L→R) ⇒ CN01_K311(R→L)","※本検査は仕様通りの搬送ﾓｰﾀ動作確認終了後に行うこと","ｺﾈｸﾀを確実に差込むこと","正流れ時は接続ｺﾈｸﾀ側① (左) ､逆流れ時② (右) のﾏｰｷﾝｸﾞﾀｲ名称に従ってｺﾈｸﾀを接続すること","左→右(正流れ)仕様時:ON","①本体→②入出力確認→③ﾘﾝｸ→④ch1→⑤ｱﾄﾞﾚｽ0044 ﾋﾞｯﾄ2･3を表示","右→左(逆流れ)仕様時:OFF","左→右(正流れ)仕様時､ｺﾈｸﾀ入替え後:OFF","右→左(逆流れ)仕様時､ｺﾈｸﾀ入替え後:ON"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:4.Sysytem ON時動作確認 (3/3) (6) 搬送流れ方向識別確認","検査表①:4.Sysytem ON時動作確認 (3/3) (6) 搬送流れ方向識別確認","検査表①:4.Sysytem ON時動作確認 (3/3) (6) 搬送流れ方向識別確認","WETE-G002-B01"],"QualityItem":"入力確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り確認する事","Method":"目視","RecordMethod":"WETE-G002-B01","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"Fﾄﾞﾗｲﾊﾞｰ接続","WorkItems":["1. 設備の電源をOFFし､ﾌﾛﾝﾄ側X･Y軸ﾄﾞﾗｲﾊﾞｰにﾊﾟﾜｰ線を接続する"],"WorkPoints":["FXﾄﾞﾗｲﾊﾞｰ","CNP3(K501)","FYﾄﾞﾗｲﾊﾞｰ","CNP3A(K502)","CNP3B(K502)","CHARGEﾗﾝﾌﾟ点灯中はﾊﾟﾜｰ線の接続は行わないこと"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["FRONT"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"Fﾄﾞﾗｲﾊﾞｰ接続","WorkItems":["1. 設備の電源をOFFし､ﾌﾛﾝﾄ側X･Y軸ﾄﾞﾗｲﾊﾞｰにﾊﾟﾜｰ線を接続する"],"WorkPoints":["FXﾄﾞﾗｲﾊﾞｰ","CNP3(K501)","FYﾄﾞﾗｲﾊﾞｰ","CNP3A(K502)","CNP3B(K502)","CHARGEﾗﾝﾌﾟ点灯中はﾊﾟﾜｰ線の接続は行わないこと"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["FRONT"],"QualityItem":"接続確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り接続する事","Method":"目視","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"","Size":"","ToolOther":"","WorkName":"Rﾄﾞﾗｲﾊﾞｰ接続","WorkItems":["1. 設備の電源をOFFし､ﾘｱ側X･Y軸ﾄﾞﾗｲﾊﾞｰにﾊﾟﾜｰ線を接続する"],"WorkPoints":["CNP3(K503)","CNP3A(K504)","CNP3B(K504)","RXﾄﾞﾗｲﾊﾞｰ","RYﾄﾞﾗｲﾊﾞｰ","CHARGEﾗﾝﾌﾟ点灯中はﾊﾟﾜｰ線の接続は行わないこと"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["REAR"]} | {"WorkTypes":[],"ToolName":"","Size":"","ToolOther":"","WorkName":"Rﾄﾞﾗｲﾊﾞｰ接続","WorkItems":["1. 設備の電源をOFFし､ﾘｱ側X･Y軸ﾄﾞﾗｲﾊﾞｰにﾊﾟﾜｰ線を接続する"],"WorkPoints":["CNP3(K503)","CNP3A(K504)","CNP3B(K504)","RXﾄﾞﾗｲﾊﾞｰ","RYﾄﾞﾗｲﾊﾞｰ","CHARGEﾗﾝﾌﾟ点灯中はﾊﾟﾜｰ線の接続は行わないこと"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["REAR"],"QualityItem":"接続確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り接続する事","Method":"目視","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸ","Size":"","ToolOther":"","WorkName":"原点復帰確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B01"]} | {"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸ","Size":"","ToolOther":"","WorkName":"原点復帰確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B01"],"QualityItem":"動作確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"目視","RecordMethod":"WETE-G002-B01","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸ","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(ｻｰﾎﾞSW)①","WorkItems":["■2. を押しながら開始を押下し原点復帰を実施すると､自己診断異常表示にて動作ができないことを確認する","1. F側 ｻｰﾎﾞSWをOFFにする","■3. R側のｻｰﾎﾞSWも同様に確認する"],"WorkPoints":["ｻｰﾎﾞｽｲｯﾁｵﾌの表示を確認する","OFF"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","F ｻｰﾎﾞSW","押す","WETE-G002-B01"]} | {"WorkTypes":[],"ToolName":"KEYﾃﾞｨｽｸ","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(ｻｰﾎﾞSW)①","WorkItems":["■2. を押しながら開始を押下し原点復帰を実施すると､自己診断異常表示にて動作ができないことを確認する","1. F側 ｻｰﾎﾞSWをOFFにする","■3. R側のｻｰﾎﾞSWも同様に確認する"],"WorkPoints":["ｻｰﾎﾞｽｲｯﾁｵﾌの表示を確認する","OFF"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","F ｻｰﾎﾞSW","押す","WETE-G002-B01"],"QualityItem":"動作確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"目視","RecordMethod":"WETE-G002-B01","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(交換台車)","WorkItems":["1. F1側の台車ｼｮｰﾄｺﾈｸﾀを取外す","■4. R1側も同様に確認する","■2. を押しながら開始を押下し原点復帰を実施すると､自己診断異常表示にて動作ができないことを確認する","■3. F2側も同様に確認する","■5. R2側も同様に確認する"],"WorkPoints":["発生位置と供給部接続ｴﾗｰの表示を確認する","17/34連","30/60連","F1:台車接続","F2:台車接続","F1:台車接続","台車ｼｮｰﾄｺﾈｸﾀを取外す","17/34連","30/60連","R1:台車接続","R2:台車接続","R1:台車接続","17/34連台車､30/60連台車､切替仕様時に確認","17/34連台車､ﾄﾚｲ固定､切替仕様時に確認","17/34連台車､30/60連台車､切替仕様時に確認","17/34連台車､ﾄﾚｲ固定､切替仕様時に確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","押す","FRONT","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","WETE-G002-B01"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(交換台車)","WorkItems":["1. F1側の台車ｼｮｰﾄｺﾈｸﾀを取外す","■4. R1側も同様に確認する","■2. を押しながら開始を押下し原点復帰を実施すると､自己診断異常表示にて動作ができないことを確認する","■3. F2側も同様に確認する","■5. R2側も同様に確認する"],"WorkPoints":["発生位置と供給部接続ｴﾗｰの表示を確認する","17/34連","30/60連","F1:台車接続","F2:台車接続","F1:台車接続","台車ｼｮｰﾄｺﾈｸﾀを取外す","17/34連","30/60連","R1:台車接続","R2:台車接続","R1:台車接続","17/34連台車､30/60連台車､切替仕様時に確認","17/34連台車､ﾄﾚｲ固定､切替仕様時に確認","17/34連台車､30/60連台車､切替仕様時に確認","17/34連台車､ﾄﾚｲ固定､切替仕様時に確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","押す","FRONT","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","WETE-G002-B01"],"QualityItem":"動作確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"目視","RecordMethod":"WETE-G002-B01","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(開閉ｶﾊﾞｰ)①","WorkItems":["■2. を押しながら開始を押下し原点復帰を実施すると､自己診断異常表示にて動作ができないことを確認する","1. F側の開閉ｶﾊﾞｰを開ける","■3. R側の開閉ｶﾊﾞｰも同様に確認する"],"WorkPoints":["発生位置とｶﾊﾞｰｵｰﾌﾟﾝの表示を確認する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","押す","FRONT","WETE-G002-B01"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(開閉ｶﾊﾞｰ)①","WorkItems":["■2. を押しながら開始を押下し原点復帰を実施すると､自己診断異常表示にて動作ができないことを確認する","1. F側の開閉ｶﾊﾞｰを開ける","■3. R側の開閉ｶﾊﾞｰも同様に確認する"],"WorkPoints":["発生位置とｶﾊﾞｰｵｰﾌﾟﾝの表示を確認する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","押す","FRONT","WETE-G002-B01"],"QualityItem":"動作確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"目視","RecordMethod":"WETE-G002-B01","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(非常停止)","WorkItems":["■1. を押しながら開始を押下し原点復帰中にF側非常停SWを押すと､設備が即停止&ｴﾗｰ表示されることを確認する","■2. R側の非常停止SWも同様に確認する"],"WorkPoints":["非常停止ｽｲｯﾁON表示を確認する","原点復帰中に押す"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","押す","WETE-G002-B01"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(非常停止)","WorkItems":["■1. を押しながら開始を押下し原点復帰中にF側非常停SWを押すと､設備が即停止&ｴﾗｰ表示されることを確認する","■2. R側の非常停止SWも同様に確認する"],"WorkPoints":["非常停止ｽｲｯﾁON表示を確認する","原点復帰中に押す"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","押す","WETE-G002-B01"],"QualityItem":"動作確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"目視","RecordMethod":"WETE-G002-B01","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(開閉ｶﾊﾞｰ)②","WorkItems":["■1. を押しながら開始を押下し原点復帰中にF側開閉ｶﾊﾞｰを開けると､設備が即停止&ｴﾗｰ表示されることを確認する","■2. R側の開閉ｶﾊﾞｰも同様に確認する"],"WorkPoints":["ｶﾊﾞｰｵｰﾌﾟﾝ(発生位置)の表示を確認する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","押す","WETE-G002-B01"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(開閉ｶﾊﾞｰ)②","WorkItems":["■1. を押しながら開始を押下し原点復帰中にF側開閉ｶﾊﾞｰを開けると､設備が即停止&ｴﾗｰ表示されることを確認する","■2. R側の開閉ｶﾊﾞｰも同様に確認する"],"WorkPoints":["ｶﾊﾞｰｵｰﾌﾟﾝ(発生位置)の表示を確認する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","押す","WETE-G002-B01"],"QualityItem":"動作確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"目視","RecordMethod":"WETE-G002-B01","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(ｻｰﾎﾞSW)②","WorkItems":["■1. を押しながら開始を押下し原点復帰中にF側ｻｰﾎﾞSWをOFFにすると､設備が即停止&ｴﾗｰ表示されることを確認する","■2. R側のｻｰﾎﾞSWも同様に確認する"],"WorkPoints":["ｻｰﾎﾞｽｲｯﾁｵﾌ表示を確認する","OFF","原点復帰中にOFFにする"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","F ｻｰﾎﾞSW","押す","WETE-G002-B01"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(ｻｰﾎﾞSW)②","WorkItems":["■1. を押しながら開始を押下し原点復帰中にF側ｻｰﾎﾞSWをOFFにすると､設備が即停止&ｴﾗｰ表示されることを確認する","■2. R側のｻｰﾎﾞSWも同様に確認する"],"WorkPoints":["ｻｰﾎﾞｽｲｯﾁｵﾌ表示を確認する","OFF","原点復帰中にOFFにする"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","F ｻｰﾎﾞSW","押す","WETE-G002-B01"],"QualityItem":"動作確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"目視","RecordMethod":"WETE-G002-B01","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(ﾌｨｰﾀﾞ開口部ｾﾝｻ)","WorkItems":["■1. を押しながら開始を押下し原点復帰中にF側のﾌｨｰﾀﾞﾞ開口部ｾﾝｻを遮光すると､ F側設備が即停止&ｴﾗｰ表示されることを確認する","■2. R側のﾌｨｰﾀﾞ開口部ｾﾝｻも同様に確認する"],"WorkPoints":["※ｾﾝｻ1ｴﾗｰ時の表示(各ｾﾝｻに対応した数字が表示される)","ﾌｨｰﾀﾞ開口部ｾﾝｻ","投光側","手前側","原点復帰中に1ヵ所づつ遮光し確認する","各ｾﾝｻに対応した表示を確認する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","押す","ｾﾝｻ1","ｾﾝｻ2","ｾﾝｻ4","ｾﾝｻ3","FRONT","WETE-G002-B01"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(ﾌｨｰﾀﾞ開口部ｾﾝｻ)","WorkItems":["■1. を押しながら開始を押下し原点復帰中にF側のﾌｨｰﾀﾞﾞ開口部ｾﾝｻを遮光すると､ F側設備が即停止&ｴﾗｰ表示されることを確認する","■2. R側のﾌｨｰﾀﾞ開口部ｾﾝｻも同様に確認する"],"WorkPoints":["※ｾﾝｻ1ｴﾗｰ時の表示(各ｾﾝｻに対応した数字が表示される)","ﾌｨｰﾀﾞ開口部ｾﾝｻ","投光側","手前側","原点復帰中に1ヵ所づつ遮光し確認する","各ｾﾝｻに対応した表示を確認する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","押す","ｾﾝｻ1","ｾﾝｻ2","ｾﾝｻ4","ｾﾝｻ3","FRONT","WETE-G002-B01"],"QualityItem":"動作確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"目視","RecordMethod":"WETE-G002-B01","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｼｮｰﾄｺﾈｸﾀ","Size":"CNEXR-S","ToolOther":"FM-2701","WorkName":"安全ﾃｽﾄ(搬送開口部ｾﾝｻ)","WorkItems":["■2. を押しながら開始を押下し原点復帰中に左側搬送開口部ｾﾝｻを遮光すると､設備が即停止&ｴﾗｰ表示されることを確認する","1. ｼｮｰﾄｺﾈｸﾀCNEXLとCNEXRが接続されている事を確認する","■3. 右側の搬送開口ｾﾝｻも同様に確認する"],"WorkPoints":["延長ｺﾝﾍﾞｱ仕様時は､延長ｺﾝﾍﾞｱ部に開口部ｾﾝｻを移行させる為､確認不要","搬送開口部ｾﾝｻ検出(発生位置)の表示を確認する","原点復帰中に開口部ｾﾝｻを遮光する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","押す","FRONT","■安全作業","WETE-G002-B01"]} | {"WorkTypes":[],"ToolName":"ｼｮｰﾄｺﾈｸﾀ","Size":"CNEXR-S","ToolOther":"FM-2701","WorkName":"安全ﾃｽﾄ(搬送開口部ｾﾝｻ)","WorkItems":["■2. を押しながら開始を押下し原点復帰中に左側搬送開口部ｾﾝｻを遮光すると､設備が即停止&ｴﾗｰ表示されることを確認する","1. ｼｮｰﾄｺﾈｸﾀCNEXLとCNEXRが接続されている事を確認する","■3. 右側の搬送開口ｾﾝｻも同様に確認する"],"WorkPoints":["延長ｺﾝﾍﾞｱ仕様時は､延長ｺﾝﾍﾞｱ部に開口部ｾﾝｻを移行させる為､確認不要","搬送開口部ｾﾝｻ検出(発生位置)の表示を確認する","原点復帰中に開口部ｾﾝｻを遮光する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","押す","FRONT","■安全作業","WETE-G002-B01"],"QualityItem":"動作確認","ToolManageNo":"FM-2701","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"目視","RecordMethod":"WETE-G002-B01","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｼｮｰﾄｺﾈｸﾀ","Size":"CNEXR-S","ToolOther":"FM-2700","WorkName":"安全ﾃｽﾄ(搬送開口部ｾﾝｻ)","WorkItems":["■2. を押しながら開始を押下し原点復帰中に左側搬送開口部ｾﾝｻを遮光すると､設備が即停止&ｴﾗｰ表示されることを確認する","1. ｼｮｰﾄｺﾈｸﾀCNEXLとCNEXRが接続されている事を確認する","■3. 右側の搬送開口ｾﾝｻも同様に確認する"],"WorkPoints":["延長ｺﾝﾍﾞｱ仕様時は､延長ｺﾝﾍﾞｱ部に開口部ｾﾝｻを移行させる為､確認不要","搬送開口部ｾﾝｻ検出(発生位置)の表示を確認する","原点復帰中に開口部ｾﾝｻを遮光する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","押す","FRONT","■安全作業","WETE-G002-B01"]} | {"WorkTypes":[],"ToolName":"ｼｮｰﾄｺﾈｸﾀ","Size":"CNEXR-S","ToolOther":"FM-2700","WorkName":"安全ﾃｽﾄ(搬送開口部ｾﾝｻ)","WorkItems":["■2. を押しながら開始を押下し原点復帰中に左側搬送開口部ｾﾝｻを遮光すると､設備が即停止&ｴﾗｰ表示されることを確認する","1. ｼｮｰﾄｺﾈｸﾀCNEXLとCNEXRが接続されている事を確認する","■3. 右側の搬送開口ｾﾝｻも同様に確認する"],"WorkPoints":["延長ｺﾝﾍﾞｱ仕様時は､延長ｺﾝﾍﾞｱ部に開口部ｾﾝｻを移行させる為､確認不要","搬送開口部ｾﾝｻ検出(発生位置)の表示を確認する","原点復帰中に開口部ｾﾝｻを遮光する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","押す","FRONT","■安全作業","WETE-G002-B01"],"QualityItem":"動作確認","ToolManageNo":"FM-2700","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"目視","RecordMethod":"WETE-G002-B01","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"下受けﾋﾟﾝ(長･短)","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(下受けﾋﾟﾝ検出)ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様","WorkItems":["3. ｴﾗｰ停止後下受けﾋﾟﾝを立て換え､ﾚｰﾙとﾋﾟﾝ間に隙間がある事を確認する","■2. ｻﾎﾟｰﾄﾌﾟﾚｰﾄに下受けﾋﾟﾝを立て､幅寄せを行った時､検出ｾﾝｻにて即停止することを確認する","1. ｻﾎﾟｰﾄﾌﾟﾚｰﾄに下受けﾋﾟﾝを立て手動で幅寄せを行い 検出ｾﾝｻがOFF(緑のみ点灯)することを確認する"],"WorkPoints":["下受けﾋﾟﾝ検出ｲﾝﾀｰﾛｯｸｾﾝｻｰが下受けﾋﾟﾝを検出して幅寄せ動作が即停止することを確認する","下受けﾋﾟﾝ位置注意","下受けﾋﾟﾝ位置注意､1箇所ずつ確認","下受けﾋﾟﾝ干渉ｴﾗｰと発生位置のﾚｰﾝ1表示を確認する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["標準仕様(X2列目･Y任意置､左右2箇所)","自動ﾋﾟﾝ仕様(X端面･Y任意置､左右2箇所)","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","標準仕様(X2列目･Y3行目)","50mm","自動ﾋﾟﾝ仕様(X端面･Y50㎜)","左図をもとに下受けﾋﾟﾝを立て､手でﾍﾞﾙﾄを回し､ｺﾝﾍﾞｱ幅を縮め､検出ｾﾝｻがOFFすることを確認する(ｺﾝﾍﾞｱ破損防止のため)","FRONT","FRONT","① 《調整》 を選択","② 《ｺﾝﾍﾞｱ》 を選択","③ 《幅調整》 を選択","押す","50 と入力し《Enter》 を押す","を押しながら《実行》を押す","検出ｾﾝｻ","WETE-G002-B01"]} | {"WorkTypes":[],"ToolName":"下受けﾋﾟﾝ(長･短)","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(下受けﾋﾟﾝ検出)ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様","WorkItems":["3. ｴﾗｰ停止後下受けﾋﾟﾝを立て換え､ﾚｰﾙとﾋﾟﾝ間に隙間がある事を確認する","■2. ｻﾎﾟｰﾄﾌﾟﾚｰﾄに下受けﾋﾟﾝを立て､幅寄せを行った時､検出ｾﾝｻにて即停止することを確認する","1. ｻﾎﾟｰﾄﾌﾟﾚｰﾄに下受けﾋﾟﾝを立て手動で幅寄せを行い 検出ｾﾝｻがOFF(緑のみ点灯)することを確認する"],"WorkPoints":["下受けﾋﾟﾝ検出ｲﾝﾀｰﾛｯｸｾﾝｻｰが下受けﾋﾟﾝを検出して幅寄せ動作が即停止することを確認する","下受けﾋﾟﾝ位置注意","下受けﾋﾟﾝ位置注意､1箇所ずつ確認","下受けﾋﾟﾝ干渉ｴﾗｰと発生位置のﾚｰﾝ1表示を確認する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["標準仕様(X2列目･Y任意置､左右2箇所)","自動ﾋﾟﾝ仕様(X端面･Y任意置､左右2箇所)","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","標準仕様(X2列目･Y3行目)","50mm","自動ﾋﾟﾝ仕様(X端面･Y50㎜)","左図をもとに下受けﾋﾟﾝを立て､手でﾍﾞﾙﾄを回し､ｺﾝﾍﾞｱ幅を縮め､検出ｾﾝｻがOFFすることを確認する(ｺﾝﾍﾞｱ破損防止のため)","FRONT","FRONT","① 《調整》 を選択","② 《ｺﾝﾍﾞｱ》 を選択","③ 《幅調整》 を選択","押す","50 と入力し《Enter》 を押す","を押しながら《実行》を押す","検出ｾﾝｻ","WETE-G002-B01"],"QualityItem":"動作確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"目視","RecordMethod":"WETE-G002-B01","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"下受けﾋﾟﾝ(長･短)","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(下受けﾋﾟﾝ検出ﾚｰﾝ1)ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様","WorkItems":["3. ｴﾗｰ停止後下受けﾋﾟﾝを立て換え､ﾚｰﾙとﾋﾟﾝ間に隙間がある事を確認する","■2. ｻﾎﾟｰﾄﾌﾟﾚｰﾄに下受けﾋﾟﾝを立て､幅寄せを行った時､検出ｾﾝｻにて即停止することを確認する","1. ｻﾎﾟｰﾄﾌﾟﾚｰﾄに下受けﾋﾟﾝを立て手動で幅寄せを行い 検出ｾﾝｻがOFF(緑のみ点灯)することを確認する"],"WorkPoints":["下受けﾋﾟﾝ検出ｲﾝﾀｰﾛｯｸｾﾝｻｰが下受けﾋﾟﾝを検出して幅寄せ動作が即停止することを確認する","下受けﾋﾟﾝ位置注意","下受けﾋﾟﾝ位置注意､1箇所ずつ確認","下受けﾋﾟﾝ干渉ｴﾗｰと発生位置のﾚｰﾝ1表示を確認する","ﾚｰﾝ1が動作"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","① 《調整》 を選択","② 《ｺﾝﾍﾞｱ》 を選択","③ 《幅調整》 を選択","① ﾚｰﾝ2を押す","②押す","標準仕様(X2列目･Y3行目)","50mm","自動ﾋﾟﾝ仕様(X端面･Y50㎜)","50 と入力し《Enter》 を押す","標準仕様(X2列目･Y任意置､左右2箇所ずつ)","自動ﾋﾟﾝ仕様(X端面･Y任意置､左右2箇所ずつ)","FRONT","FRONT","を押しながら《実行》を押す","検出ｾﾝｻ","左図をもとに下受けﾋﾟﾝを立て､手でﾍﾞﾙﾄを回し､ｺﾝﾍﾞｱ幅を縮め､検出ｾﾝｻがOFFすることを確認する(ｺﾝﾍﾞｱ破損防止のため)","WETE-G002-B01"]} | {"WorkTypes":[],"ToolName":"下受けﾋﾟﾝ(長･短)","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(下受けﾋﾟﾝ検出ﾚｰﾝ1)ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様","WorkItems":["3. ｴﾗｰ停止後下受けﾋﾟﾝを立て換え､ﾚｰﾙとﾋﾟﾝ間に隙間がある事を確認する","■2. ｻﾎﾟｰﾄﾌﾟﾚｰﾄに下受けﾋﾟﾝを立て､幅寄せを行った時､検出ｾﾝｻにて即停止することを確認する","1. ｻﾎﾟｰﾄﾌﾟﾚｰﾄに下受けﾋﾟﾝを立て手動で幅寄せを行い 検出ｾﾝｻがOFF(緑のみ点灯)することを確認する"],"WorkPoints":["下受けﾋﾟﾝ検出ｲﾝﾀｰﾛｯｸｾﾝｻｰが下受けﾋﾟﾝを検出して幅寄せ動作が即停止することを確認する","下受けﾋﾟﾝ位置注意","下受けﾋﾟﾝ位置注意､1箇所ずつ確認","下受けﾋﾟﾝ干渉ｴﾗｰと発生位置のﾚｰﾝ1表示を確認する","ﾚｰﾝ1が動作"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","① 《調整》 を選択","② 《ｺﾝﾍﾞｱ》 を選択","③ 《幅調整》 を選択","① ﾚｰﾝ2を押す","②押す","標準仕様(X2列目･Y3行目)","50mm","自動ﾋﾟﾝ仕様(X端面･Y50㎜)","50 と入力し《Enter》 を押す","標準仕様(X2列目･Y任意置､左右2箇所ずつ)","自動ﾋﾟﾝ仕様(X端面･Y任意置､左右2箇所ずつ)","FRONT","FRONT","を押しながら《実行》を押す","検出ｾﾝｻ","左図をもとに下受けﾋﾟﾝを立て､手でﾍﾞﾙﾄを回し､ｺﾝﾍﾞｱ幅を縮め､検出ｾﾝｻがOFFすることを確認する(ｺﾝﾍﾞｱ破損防止のため)","WETE-G002-B01"],"QualityItem":"動作確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"目視","RecordMethod":"WETE-G002-B01","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"下受けﾋﾟﾝ(長･短)","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(下受けﾋﾟﾝ検出ﾚｰﾝ2)ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様","WorkItems":["1. ｻﾎﾟｰﾄﾌﾟﾚｰﾄに下受けﾋﾟﾝを立て手動で幅寄せを行い 検出ｾﾝｻがOFF(緑のみ点灯)することを確認する","■2. ｻﾎﾟｰﾄﾌﾟﾚｰﾄに下受けﾋﾟﾝを立て､幅寄せを行った時､検出ｾﾝｻにて即停止することを確認する","3. ｴﾗｰ停止後下受けﾋﾟﾝを立て換え､ﾚｰﾙとﾋﾟﾝ間に隙間がある事を確認する"],"WorkPoints":["下受けﾋﾟﾝ位置注意､1箇所ずつ確認","下受けﾋﾟﾝ検出ｲﾝﾀｰﾛｯｸｾﾝｻｰが下受けﾋﾟﾝを検出して幅寄せ動作が即停止することを確認する","下受けﾋﾟﾝ位置注意","ﾚｰﾝ2が動作","下受けﾋﾟﾝ干渉ｴﾗｰと発生位置のﾚｰﾝ2表示を確認する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["50mm","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","① 《調整》 を選択","② 《ｺﾝﾍﾞｱ》 を選択","③ 《幅調整》 を選択","②押す","① ﾚｰﾝ1を押す","50 と入力し《Enter》 を押す","標準仕様(X2列目･Y3行目)","50mm","自動ﾋﾟﾝ仕様(X端面･Y50㎜)","FRONT","標準仕様(X2列目･Y任意置､左右2箇所ずつ)","自動ﾋﾟﾝ仕様(X端面･Y任意置､左右2箇所ずつ)","FRONT","を押しながら《実行》を押す","検出ｾﾝｻ","左図をもとに下受けﾋﾟﾝを立て､手でﾍﾞﾙﾄを回し､ｺﾝﾍﾞｱ幅を縮め､検出ｾﾝｻがOFFすることを確認する(ｺﾝﾍﾞｱ破損防止のため)","WETE-G002-B01"]} | {"WorkTypes":[],"ToolName":"下受けﾋﾟﾝ(長･短)","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(下受けﾋﾟﾝ検出ﾚｰﾝ2)ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様","WorkItems":["1. ｻﾎﾟｰﾄﾌﾟﾚｰﾄに下受けﾋﾟﾝを立て手動で幅寄せを行い 検出ｾﾝｻがOFF(緑のみ点灯)することを確認する","■2. ｻﾎﾟｰﾄﾌﾟﾚｰﾄに下受けﾋﾟﾝを立て､幅寄せを行った時､検出ｾﾝｻにて即停止することを確認する","3. ｴﾗｰ停止後下受けﾋﾟﾝを立て換え､ﾚｰﾙとﾋﾟﾝ間に隙間がある事を確認する"],"WorkPoints":["下受けﾋﾟﾝ位置注意､1箇所ずつ確認","下受けﾋﾟﾝ検出ｲﾝﾀｰﾛｯｸｾﾝｻｰが下受けﾋﾟﾝを検出して幅寄せ動作が即停止することを確認する","下受けﾋﾟﾝ位置注意","ﾚｰﾝ2が動作","下受けﾋﾟﾝ干渉ｴﾗｰと発生位置のﾚｰﾝ2表示を確認する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["50mm","検査表①:5.Power ON時動作確認 (3) Power ON時 安全ﾃｽﾄ","① 《調整》 を選択","② 《ｺﾝﾍﾞｱ》 を選択","③ 《幅調整》 を選択","②押す","① ﾚｰﾝ1を押す","50 と入力し《Enter》 を押す","標準仕様(X2列目･Y3行目)","50mm","自動ﾋﾟﾝ仕様(X端面･Y50㎜)","FRONT","標準仕様(X2列目･Y任意置､左右2箇所ずつ)","自動ﾋﾟﾝ仕様(X端面･Y任意置､左右2箇所ずつ)","FRONT","を押しながら《実行》を押す","検出ｾﾝｻ","左図をもとに下受けﾋﾟﾝを立て､手でﾍﾞﾙﾄを回し､ｺﾝﾍﾞｱ幅を縮め､検出ｾﾝｻがOFFすることを確認する(ｺﾝﾍﾞｱ破損防止のため)","WETE-G002-B01"],"QualityItem":"動作確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"目視","RecordMethod":"WETE-G002-B01","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(ｵﾌﾟｼｮﾝ:延長ｺﾝﾍﾞｱ開口部ｾﾝｻ)","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B01"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"安全ﾃｽﾄ(ｵﾌﾟｼｮﾝ:延長ｺﾝﾍﾞｱ開口部ｾﾝｻ)","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WETE-G002-B01"],"QualityItem":"動作確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り動作出来ている事","Method":"目視","RecordMethod":"WETE-G002-B01","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾍｯﾄﾞ診断用SD","Size":"","ToolOther":"","WorkName":"ﾍｯﾄﾞ診断①","WorkItems":["7. ⑥ 操作ﾊﾟﾈﾙの を押しながら 『計測ｽﾀｰﾄ』を押す","2. ① 《ﾒﾝﾃﾅﾝｽ》 を押す","4. ③ 《ﾍｯﾄﾞ診断》 を押す","5. ④ 4項目を押し選択を解除する","3. ② 《ﾍｯﾄﾞ》 を押す","1. ㉖ ヘッド診断用SDをドライブに挿入する","6. ⑤ 3項目の選択が選択されているのを確認する","8. ⑦ 計測終了後､3項目のﾁｪｯｸが 《OK》 になっているか確認する","9. ⑧ 《計測結果》 を押し､計測結果を確認する"],"WorkPoints":["･ｴｱ漏れﾁｪｯｸ(ﾌﾞﾛｰ)･ｴｱ漏れﾁｪｯｸ(ﾊﾞｷｭｰﾑ)･θ軸動作ﾁｪｯｸ･ Z 軸動作ﾁｪｯｸ※上記4項目は選択解除すること","･流量ｾﾝｻ ｾﾞﾛﾁｪｯｸ･ｴｱつまりﾁｪｯｸ(ﾌﾞﾛｰ)･ｴｱつまりﾁｪｯｸ(ﾊﾞｷｭｰﾑ)※上記3項目は選択されていること"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["FRONT"]} | {"WorkTypes":[],"ToolName":"ﾍｯﾄﾞ診断用SD","Size":"","ToolOther":"","WorkName":"ﾍｯﾄﾞ診断①","WorkItems":["7. ⑥ 操作ﾊﾟﾈﾙの を押しながら 『計測ｽﾀｰﾄ』を押す","2. ① 《ﾒﾝﾃﾅﾝｽ》 を押す","4. ③ 《ﾍｯﾄﾞ診断》 を押す","5. ④ 4項目を押し選択を解除する","3. ② 《ﾍｯﾄﾞ》 を押す","1. ㉖ ヘッド診断用SDをドライブに挿入する","6. ⑤ 3項目の選択が選択されているのを確認する","8. ⑦ 計測終了後､3項目のﾁｪｯｸが 《OK》 になっているか確認する","9. ⑧ 《計測結果》 を押し､計測結果を確認する"],"WorkPoints":["･ｴｱ漏れﾁｪｯｸ(ﾌﾞﾛｰ)･ｴｱ漏れﾁｪｯｸ(ﾊﾞｷｭｰﾑ)･θ軸動作ﾁｪｯｸ･ Z 軸動作ﾁｪｯｸ※上記4項目は選択解除すること","･流量ｾﾝｻ ｾﾞﾛﾁｪｯｸ･ｴｱつまりﾁｪｯｸ(ﾌﾞﾛｰ)･ｴｱつまりﾁｪｯｸ(ﾊﾞｷｭｰﾑ)※上記3項目は選択されていること"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["FRONT"],"QualityItem":"表示確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"ｴﾗｰ無き事","Method":"目視","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾍｯﾄﾞ診断用SD","Size":"","ToolOther":"","WorkName":"ﾍｯﾄﾞ診断②","WorkItems":["1. ① 計測結果を確認し､ｴﾗｰ(黄色)がないことを確認する","2. ② 《戻る》 を押す","3. ③ 《ﾃﾞｰﾀ転送》 を押す","4. ④ 《LNB 》 を押し､LNBにﾃﾞｰﾀを転送する","5. ⑤ 《TBL2》 を押し､5~13までを同様に実施する","6. LNBにて転送ﾃﾞｰﾀにｴﾗｰが無いことを確認する"],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["頁切替えし全て確認する","検査表①:4.Sysytem ON時動作確認 (2/3) (5) 圧力設定と確認 (2/2)","WETE-G002-B01"]} | {"WorkTypes":[],"ToolName":"ﾍｯﾄﾞ診断用SD","Size":"","ToolOther":"","WorkName":"ﾍｯﾄﾞ診断②","WorkItems":["1. ① 計測結果を確認し､ｴﾗｰ(黄色)がないことを確認する","2. ② 《戻る》 を押す","3. ③ 《ﾃﾞｰﾀ転送》 を押す","4. ④ 《LNB 》 を押し､LNBにﾃﾞｰﾀを転送する","5. ⑤ 《TBL2》 を押し､5~13までを同様に実施する","6. LNBにて転送ﾃﾞｰﾀにｴﾗｰが無いことを確認する"],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["頁切替えし全て確認する","検査表①:4.Sysytem ON時動作確認 (2/3) (5) 圧力設定と確認 (2/2)","WETE-G002-B01"],"QualityItem":"表示確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"ｴﾗｰ無き事","Method":"目視","RecordMethod":"WETE-G002-B01","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"駆動部ﾌﾚｰﾑ吊り上げ、金ﾆｽ塗装","WorkItems":["◆2. FRAME の指示した場所以外の加工面に金ﾆｽ塗装を行う","1. FRAME 本圧着ﾌﾚｰﾑの加工面(下面以外)全てを油砥石で均す","◆3. FRAME をﾘﾌﾀｰ(ｸﾚｰﾝ)で吊り上げ本圧着ﾌﾚｰﾑ下面を油砥石で均す"],"WorkPoints":["ﾓｰﾀｰ取付け面","ﾌﾚｰﾑ前側基準面(LMｶﾞｲﾄﾞ取付基準面)","この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)","LMｶﾞｲﾄﾞ取付け面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["下記の指示部には金二ｽ塗布はしない｡(LMｶﾞｲﾄﾞ､ﾓｰﾀｰ取付後に塗布すること)","◆作業者安全作業"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"駆動部ﾌﾚｰﾑ吊り上げ、金ﾆｽ塗装","WorkItems":["◆2. FRAME の指示した場所以外の加工面に金ﾆｽ塗装を行う","1. FRAME 本圧着ﾌﾚｰﾑの加工面(下面以外)全てを油砥石で均す","◆3. FRAME をﾘﾌﾀｰ(ｸﾚｰﾝ)で吊り上げ本圧着ﾌﾚｰﾑ下面を油砥石で均す"],"WorkPoints":["ﾓｰﾀｰ取付け面","ﾌﾚｰﾑ前側基準面(LMｶﾞｲﾄﾞ取付基準面)","この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)","LMｶﾞｲﾄﾞ取付け面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["下記の指示部には金二ｽ塗布はしない｡(LMｶﾞｲﾄﾞ､ﾓｰﾀｰ取付後に塗布すること)","◆作業者安全作業"],"QualityItem":"金ﾆｽ塗布確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示箇所に塗布されている事","Method":"目視","RecordMethod":"-","Other":"金ﾆｽ","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"駆動部ﾌﾚｰﾑ吊り上げ、金ﾆｽ塗装","WorkItems":["◆2. FRAME の指示した場所以外の加工面に金ﾆｽ塗装を行う","1. FRAME 本圧着ﾌﾚｰﾑの加工面(下面以外)全てを油砥石で均す","◆3. FRAME をﾘﾌﾀｰ(ｸﾚｰﾝ)で吊り上げ本圧着ﾌﾚｰﾑ下面を油砥石で均す"],"WorkPoints":["ﾓｰﾀｰ取付け面","ﾌﾚｰﾑ前側基準面(LMｶﾞｲﾄﾞ取付基準面)","この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)","LMｶﾞｲﾄﾞ取付け面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["下記の指示部には金二ｽ塗布はしない｡(LMｶﾞｲﾄﾞ､ﾓｰﾀｰ取付後に塗布すること)","◆作業者安全作業"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"駆動部ﾌﾚｰﾑ吊り上げ、金ﾆｽ塗装","WorkItems":["◆2. FRAME の指示した場所以外の加工面に金ﾆｽ塗装を行う","1. FRAME 本圧着ﾌﾚｰﾑの加工面(下面以外)全てを油砥石で均す","◆3. FRAME をﾘﾌﾀｰ(ｸﾚｰﾝ)で吊り上げ本圧着ﾌﾚｰﾑ下面を油砥石で均す"],"WorkPoints":["ﾓｰﾀｰ取付け面","ﾌﾚｰﾑ前側基準面(LMｶﾞｲﾄﾞ取付基準面)","この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)","LMｶﾞｲﾄﾞ取付け面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["下記の指示部には金二ｽ塗布はしない｡(LMｶﾞｲﾄﾞ､ﾓｰﾀｰ取付後に塗布すること)","◆作業者安全作業"],"QualityItem":"取付確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り取付出来ている事","Method":"目視","RecordMethod":"-","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"駆動部ﾌﾚｰﾑにﾋﾟﾝ圧入","WorkItems":["1. にPIN を圧入する"],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["出代1.5mm","出代:2.5㎜","出代:5㎜","PIN ﾋﾟﾝの圧入位置と出代に注意する"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"駆動部ﾌﾚｰﾑにﾋﾟﾝ圧入","WorkItems":["1. にPIN を圧入する"],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["出代1.5mm","出代:2.5㎜","出代:5㎜","PIN ﾋﾟﾝの圧入位置と出代に注意する"],"QualityItem":"PIN出代","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"出代:1.5㎜±0.5㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"駆動部ﾌﾚｰﾑにﾋﾟﾝ圧入","WorkItems":["1. にPIN を圧入する"],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["出代1.5mm","出代:2.5㎜","出代:5㎜","PIN ﾋﾟﾝの圧入位置と出代に注意する"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"駆動部ﾌﾚｰﾑにﾋﾟﾝ圧入","WorkItems":["1. にPIN を圧入する"],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["出代1.5mm","出代:2.5㎜","出代:5㎜","PIN ﾋﾟﾝの圧入位置と出代に注意する"],"QualityItem":"PIN出代","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"出代:2.5㎜±0.5㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"駆動部ﾌﾚｰﾑにﾋﾟﾝ圧入","WorkItems":["1. にPIN を圧入する"],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["出代1.5mm","出代:2.5㎜","出代:5㎜","PIN ﾋﾟﾝの圧入位置と出代に注意する"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"駆動部ﾌﾚｰﾑにﾋﾟﾝ圧入","WorkItems":["1. にPIN を圧入する"],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["出代1.5mm","出代:2.5㎜","出代:5㎜","PIN ﾋﾟﾝの圧入位置と出代に注意する"],"QualityItem":"PIN出代","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"出代:5.0㎜±0.5㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"H軸LMｶﾞｲﾄﾞ取付け①","WorkItems":[],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["1. にLINEAR-WAY をBOLT で固定する(従動側は仮固定)","･LINEAR-WAY の取付け位置､方向に注意する･LINEAR-WAY を のﾋﾟﾝと隙間が無いよう取付け･仮固定:SD-0169115-004にて本締め","基準面は光っている側","検査表 :H軸LMｶﾞｲﾄﾞﾋﾟﾝ当て確認","基準側のLMｶﾞｲﾄﾞは刻印の側末尾***-KBを使用","駆動部基準側LMｶﾞｲﾄﾞ","駆動部従動側LMｶﾞｲﾄﾞ","ﾋﾟﾝ当て隙間ﾁｪｯｸ","基準面は光っている側","検査表 :重要部品確認","LMｶﾞｲﾄﾞ:型式確認･ｼﾘｱﾙNo.記入","隙間:0.01mm未満","WWYJ-5300-062"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"H軸LMｶﾞｲﾄﾞ取付け①","WorkItems":[],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["1. にLINEAR-WAY をBOLT で固定する(従動側は仮固定)","･LINEAR-WAY の取付け位置､方向に注意する･LINEAR-WAY を のﾋﾟﾝと隙間が無いよう取付け･仮固定:SD-0169115-004にて本締め","基準面は光っている側","検査表 :H軸LMｶﾞｲﾄﾞﾋﾟﾝ当て確認","基準側のLMｶﾞｲﾄﾞは刻印の側末尾***-KBを使用","駆動部基準側LMｶﾞｲﾄﾞ","駆動部従動側LMｶﾞｲﾄﾞ","ﾋﾟﾝ当て隙間ﾁｪｯｸ","基準面は光っている側","検査表 :重要部品確認","LMｶﾞｲﾄﾞ:型式確認･ｼﾘｱﾙNo.記入","隙間:0.01mm未満","WWYJ-5300-062"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-062","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"H軸LMｶﾞｲﾄﾞ取付け①","WorkItems":[],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["1. にLINEAR-WAY をBOLT で固定する(従動側は仮固定)","･LINEAR-WAY の取付け位置､方向に注意する･LINEAR-WAY を のﾋﾟﾝと隙間が無いよう取付け･仮固定:SD-0169115-004にて本締め","基準面は光っている側","検査表 :H軸LMｶﾞｲﾄﾞﾋﾟﾝ当て確認","基準側のLMｶﾞｲﾄﾞは刻印の側末尾***-KBを使用","駆動部基準側LMｶﾞｲﾄﾞ","駆動部従動側LMｶﾞｲﾄﾞ","ﾋﾟﾝ当て隙間ﾁｪｯｸ","基準面は光っている側","検査表 :重要部品確認","LMｶﾞｲﾄﾞ:型式確認･ｼﾘｱﾙNo.記入","隙間:0.01mm未満","WWYJ-5300-062"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"H軸LMｶﾞｲﾄﾞ取付け①","WorkItems":[],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["1. にLINEAR-WAY をBOLT で固定する(従動側は仮固定)","･LINEAR-WAY の取付け位置､方向に注意する･LINEAR-WAY を のﾋﾟﾝと隙間が無いよう取付け･仮固定:SD-0169115-004にて本締め","基準面は光っている側","検査表 :H軸LMｶﾞｲﾄﾞﾋﾟﾝ当て確認","基準側のLMｶﾞｲﾄﾞは刻印の側末尾***-KBを使用","駆動部基準側LMｶﾞｲﾄﾞ","駆動部従動側LMｶﾞｲﾄﾞ","ﾋﾟﾝ当て隙間ﾁｪｯｸ","基準面は光っている側","検査表 :重要部品確認","LMｶﾞｲﾄﾞ:型式確認･ｼﾘｱﾙNo.記入","隙間:0.01mm未満","WWYJ-5300-062"],"QualityItem":"製造番号記録","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"製造番号転記","Method":"目視","RecordMethod":"WWYJ-5300-062","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｼｯｸﾈｽｹﾞｰｼﾞ","Size":"0.01㎜","ToolOther":"","WorkName":"H軸LMｶﾞｲﾄﾞ取付け①","WorkItems":[],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["1. にLINEAR-WAY をBOLT で固定する(従動側は仮固定)","･LINEAR-WAY の取付け位置､方向に注意する･LINEAR-WAY を のﾋﾟﾝと隙間が無いよう取付け･仮固定:SD-0169115-004にて本締め","基準面は光っている側","検査表 :H軸LMｶﾞｲﾄﾞﾋﾟﾝ当て確認","基準側のLMｶﾞｲﾄﾞは刻印の側末尾***-KBを使用","駆動部基準側LMｶﾞｲﾄﾞ","駆動部従動側LMｶﾞｲﾄﾞ","ﾋﾟﾝ当て隙間ﾁｪｯｸ","基準面は光っている側","検査表 :重要部品確認","LMｶﾞｲﾄﾞ:型式確認･ｼﾘｱﾙNo.記入","隙間:0.01mm未満","WWYJ-5300-062"]} | {"WorkTypes":[],"ToolName":"ｼｯｸﾈｽｹﾞｰｼﾞ","Size":"0.01㎜","ToolOther":"","WorkName":"H軸LMｶﾞｲﾄﾞ取付け①","WorkItems":[],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["1. にLINEAR-WAY をBOLT で固定する(従動側は仮固定)","･LINEAR-WAY の取付け位置､方向に注意する･LINEAR-WAY を のﾋﾟﾝと隙間が無いよう取付け･仮固定:SD-0169115-004にて本締め","基準面は光っている側","検査表 :H軸LMｶﾞｲﾄﾞﾋﾟﾝ当て確認","基準側のLMｶﾞｲﾄﾞは刻印の側末尾***-KBを使用","駆動部基準側LMｶﾞｲﾄﾞ","駆動部従動側LMｶﾞｲﾄﾞ","ﾋﾟﾝ当て隙間ﾁｪｯｸ","基準面は光っている側","検査表 :重要部品確認","LMｶﾞｲﾄﾞ:型式確認･ｼﾘｱﾙNo.記入","隙間:0.01mm未満","WWYJ-5300-062"],"QualityItem":"隙間確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"隙間:0.01㎜以下","Method":"ｼｯｸﾈｽｹﾞｰｼﾞ","RecordMethod":"WWYJ-5300-062","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ","Size":"","ToolOther":"","WorkName":"H軸LMｶﾞｲﾄﾞ取付け②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WWYJ-5300-062"]} | {"WorkTypes":[],"ToolName":"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ","Size":"","ToolOther":"","WorkName":"H軸LMｶﾞｲﾄﾞ取付け②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WWYJ-5300-062"],"QualityItem":"平行度確認","ToolManageNo":"-","ToolCycle":"1回/半年","ToolRecord":"校正成績書","StdVal":"60㎜の範囲で0.01㎜以下","Method":"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ","RecordMethod":"WWYJ-5300-062","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"H軸LMｶﾞｲﾄﾞ取付け②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"H軸LMｶﾞｲﾄﾞ取付け②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"金ﾆｽ塗布確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示箇所に塗布されている事","Method":"目視","RecordMethod":"-","Other":"金ﾆｽ","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"ﾍｯﾄﾞ配置部ｼﾘﾝﾀﾞｰ移動LMｶﾞｲﾄﾞ取付け①","WorkItems":["1. にLINEAR-WAY をBOLT で仮固定する"],"WorkPoints":["･LINEAR-WAY の取付け位置､方向に注意する･LINEAR-WAY を のﾋﾟﾝに当付ける(隙間:0.01㎜以下)","基準側(研磨面)を写真左側に向ける","基準側(研磨面)を写真左側に向ける","SD-0169115-006 調整後締付けする","型式確認","この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["LMｶﾞｲﾄﾞﾚｰﾙをﾋﾟﾝに隙間無き様当付ける","検査表 :重要部品確認","WWYJ-5300-064"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"ﾍｯﾄﾞ配置部ｼﾘﾝﾀﾞｰ移動LMｶﾞｲﾄﾞ取付け①","WorkItems":["1. にLINEAR-WAY をBOLT で仮固定する"],"WorkPoints":["･LINEAR-WAY の取付け位置､方向に注意する･LINEAR-WAY を のﾋﾟﾝに当付ける(隙間:0.01㎜以下)","基準側(研磨面)を写真左側に向ける","基準側(研磨面)を写真左側に向ける","SD-0169115-006 調整後締付けする","型式確認","この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["LMｶﾞｲﾄﾞﾚｰﾙをﾋﾟﾝに隙間無き様当付ける","検査表 :重要部品確認","WWYJ-5300-064"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-064","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｼｯｸﾈｽｹﾞｰｼﾞ","Size":"0.01㎜","ToolOther":"","WorkName":"ﾍｯﾄﾞ配置部ｼﾘﾝﾀﾞｰ移動LMｶﾞｲﾄﾞ取付け①","WorkItems":["1. にLINEAR-WAY をBOLT で仮固定する"],"WorkPoints":["･LINEAR-WAY の取付け位置､方向に注意する･LINEAR-WAY を のﾋﾟﾝに当付ける(隙間:0.01㎜以下)","基準側(研磨面)を写真左側に向ける","基準側(研磨面)を写真左側に向ける","SD-0169115-006 調整後締付けする","型式確認","この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["LMｶﾞｲﾄﾞﾚｰﾙをﾋﾟﾝに隙間無き様当付ける","検査表 :重要部品確認","WWYJ-5300-064"]} | {"WorkTypes":[],"ToolName":"ｼｯｸﾈｽｹﾞｰｼﾞ","Size":"0.01㎜","ToolOther":"","WorkName":"ﾍｯﾄﾞ配置部ｼﾘﾝﾀﾞｰ移動LMｶﾞｲﾄﾞ取付け①","WorkItems":["1. にLINEAR-WAY をBOLT で仮固定する"],"WorkPoints":["･LINEAR-WAY の取付け位置､方向に注意する･LINEAR-WAY を のﾋﾟﾝに当付ける(隙間:0.01㎜以下)","基準側(研磨面)を写真左側に向ける","基準側(研磨面)を写真左側に向ける","SD-0169115-006 調整後締付けする","型式確認","この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["LMｶﾞｲﾄﾞﾚｰﾙをﾋﾟﾝに隙間無き様当付ける","検査表 :重要部品確認","WWYJ-5300-064"],"QualityItem":"隙間確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"隙間:0.01㎜以下","Method":"ｼｯｸﾈｽｹﾞｰｼﾞ","RecordMethod":"WWYJ-5300-064","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ","Size":"","ToolOther":"","WorkName":"ﾍｯﾄﾞ配置部ｼﾘﾝﾀﾞｰ移動LMｶﾞｲﾄﾞ取付け②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WWYJ-5300-064"]} | {"WorkTypes":[],"ToolName":"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ","Size":"","ToolOther":"","WorkName":"ﾍｯﾄﾞ配置部ｼﾘﾝﾀﾞｰ移動LMｶﾞｲﾄﾞ取付け②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WWYJ-5300-064"],"QualityItem":"平行度確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"全ｽﾄﾛｰｸで0.02㎜以下","Method":"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ","RecordMethod":"WWYJ-5300-064","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ","Size":"","ToolOther":"","WorkName":"ﾍｯﾄﾞ配置部ｼﾘﾝﾀﾞｰ移動LMｶﾞｲﾄﾞ取付け②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WWYJ-5300-064"]} | {"WorkTypes":[],"ToolName":"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ","Size":"","ToolOther":"","WorkName":"ﾍｯﾄﾞ配置部ｼﾘﾝﾀﾞｰ移動LMｶﾞｲﾄﾞ取付け②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WWYJ-5300-064"],"QualityItem":"隙間確認","ToolManageNo":"-","ToolCycle":"1回/半年","ToolRecord":"校正成績書","StdVal":"隙間:0.01㎜以下","Method":"ｼｯｸﾈｽｹﾞｰｼﾞ","RecordMethod":"WWYJ-5300-064","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"ﾍｯﾄﾞ配置部ｼﾘﾝﾀﾞｰ移動LMｶﾞｲﾄﾞ取付け②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"ﾍｯﾄﾞ配置部ｼﾘﾝﾀﾞｰ移動LMｶﾞｲﾄﾞ取付け②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"金ﾆｽ塗布確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示箇所に塗布されている事","Method":"目視","RecordMethod":"-","Other":"金ﾆｽ","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組立①","WorkItems":["◆1. BRACKET 部品の指定以外の加工面に金ﾆｽ塗装を行う","2.1完成品にPIN を圧入する"],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["ﾋﾟﾝ出代5mm","◆作業者安全作業","外周だけでなく内面の加工面に金ﾆｽ塗布を忘れないこと","金二ｽ塗布禁止","金二ｽ塗布する事(BRACKET ﾌﾚｰﾑの内面は塗布しておく)","ﾋﾟﾝ出代に注意し圧入する"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組立①","WorkItems":["◆1. BRACKET 部品の指定以外の加工面に金ﾆｽ塗装を行う","2.1完成品にPIN を圧入する"],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["ﾋﾟﾝ出代5mm","◆作業者安全作業","外周だけでなく内面の加工面に金ﾆｽ塗布を忘れないこと","金二ｽ塗布禁止","金二ｽ塗布する事(BRACKET ﾌﾚｰﾑの内面は塗布しておく)","ﾋﾟﾝ出代に注意し圧入する"],"QualityItem":"金ﾆｽ塗布確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示箇所に塗布されている事","Method":"目視","RecordMethod":"-","Other":"金ﾆｽ","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組立①","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["ﾋﾟﾝ出代5mm","◆作業者安全作業","金二ｽ塗布する事(BRACKET ﾌﾚｰﾑの内面は塗布しておく)"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組立①","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["ﾋﾟﾝ出代5mm","◆作業者安全作業","金二ｽ塗布する事(BRACKET ﾌﾚｰﾑの内面は塗布しておく)"],"QualityItem":"PIN出代","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"出代:5.0㎜±0.5㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組立②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WWYJ-5300-062"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組立②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WWYJ-5300-062"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-062","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組立②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WWYJ-5300-062"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組立②","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WWYJ-5300-062"],"QualityItem":"製造番号記録","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"製造番号転記","Method":"目視","RecordMethod":"WWYJ-5300-062","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組立③","WorkItems":["1. に を挿入しBOLT を仮止め","◆2. 1完成品のﾎﾞｰﾙﾈｼﾞ周辺に金ﾆｽを塗布する"],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[" 仮付け後､金ﾆｽを塗布する","ｸﾞﾘｰｽﾆｯﾌﾟﾙの位置","･ の取付け位置に注意する･仮止め:SD-0169115-013にて本締め(ﾎﾞｰﾙﾈｼﾞ均しのため)(参考:ﾎﾞｰﾙﾎﾟｲﾝﾄﾚﾝﾁで負荷が指に伝わって5度緩める)"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組立③","WorkItems":["1. に を挿入しBOLT を仮止め","◆2. 1完成品のﾎﾞｰﾙﾈｼﾞ周辺に金ﾆｽを塗布する"],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[" 仮付け後､金ﾆｽを塗布する","ｸﾞﾘｰｽﾆｯﾌﾟﾙの位置","･ の取付け位置に注意する･仮止め:SD-0169115-013にて本締め(ﾎﾞｰﾙﾈｼﾞ均しのため)(参考:ﾎﾞｰﾙﾎﾟｲﾝﾄﾚﾝﾁで負荷が指に伝わって5度緩める)"],"QualityItem":"金ﾆｽ塗布確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示箇所に塗布されている事","Method":"目視","RecordMethod":"-","Other":"金ﾆｽ","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組込み①","WorkItems":["◆1. に をBOLT で16箇所で固定する(重量物のためｸﾚｰﾝを使用すること)"],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[" のﾋﾟﾝを ﾘﾆｱﾌﾞﾛｯｸに当てつけ(隙間:0.01㎜以下)"," のﾋﾟﾝに隙間無く当付ける"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組込み①","WorkItems":["◆1. に をBOLT で16箇所で固定する(重量物のためｸﾚｰﾝを使用すること)"],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[" のﾋﾟﾝを ﾘﾆｱﾌﾞﾛｯｸに当てつけ(隙間:0.01㎜以下)"," のﾋﾟﾝに隙間無く当付ける"],"QualityItem":"取付確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り取付出来ている事","Method":"目視","RecordMethod":"-","Other":"重量物","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｼｯｸﾈｽｹﾞｰｼﾞ","Size":"0.01㎜","ToolOther":"","WorkName":"H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組込み①","WorkItems":["◆1. に をBOLT で16箇所で固定する(重量物のためｸﾚｰﾝを使用すること)"],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[" のﾋﾟﾝを ﾘﾆｱﾌﾞﾛｯｸに当てつけ(隙間:0.01㎜以下)"," のﾋﾟﾝに隙間無く当付ける"]} | {"WorkTypes":[],"ToolName":"ｼｯｸﾈｽｹﾞｰｼﾞ","Size":"0.01㎜","ToolOther":"","WorkName":"H軸ﾎﾞｰﾙねじﾊｳｼﾞﾝｸﾞ部組込み①","WorkItems":["◆1. に をBOLT で16箇所で固定する(重量物のためｸﾚｰﾝを使用すること)"],"WorkPoints":["この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[" のﾋﾟﾝを ﾘﾆｱﾌﾞﾛｯｸに当てつけ(隙間:0.01㎜以下)"," のﾋﾟﾝに隙間無く当付ける"],"QualityItem":"隙間確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"隙間:0.01㎜以下","Method":"ｼｯｸﾈｽｹﾞｰｼﾞ","RecordMethod":"-","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"ﾓｰﾀｰﾌﾞﾗｹｯﾄ組立","WorkItems":["◆1. MOTOR-BRACKET の下面及び左側面以外の外周りの加工面に金ﾆｽを塗装する","◆2. BEARING にｸﾞﾘｰｽをいれIﾏｰｸを合わせる","3. 2完成品にPLATE をBOLT で締結する"],"WorkPoints":["･BEARING ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝｸﾞはﾏｰｸを合わせ､MOTOR-BRACKET に挿入する(正面合わせ､刻印あわせ)","挿入時方向に注意する","取付け後､隙間を確認(0.01㎜以上)","塗布禁止場所(ﾓｰﾀｰ取付け面､ﾌﾚｰﾑ取付け面)","この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["刻印を合わせる","印4箇所の隙間があるかﾁｪｯｸする(隙間が無いときはﾘｰﾀﾞｰへ)","左側面","下面","空間容積の30%~40%"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"ﾓｰﾀｰﾌﾞﾗｹｯﾄ組立","WorkItems":["◆1. MOTOR-BRACKET の下面及び左側面以外の外周りの加工面に金ﾆｽを塗装する","◆2. BEARING にｸﾞﾘｰｽをいれIﾏｰｸを合わせる","3. 2完成品にPLATE をBOLT で締結する"],"WorkPoints":["･BEARING ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝｸﾞはﾏｰｸを合わせ､MOTOR-BRACKET に挿入する(正面合わせ､刻印あわせ)","挿入時方向に注意する","取付け後､隙間を確認(0.01㎜以上)","塗布禁止場所(ﾓｰﾀｰ取付け面､ﾌﾚｰﾑ取付け面)","この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["刻印を合わせる","印4箇所の隙間があるかﾁｪｯｸする(隙間が無いときはﾘｰﾀﾞｰへ)","左側面","下面","空間容積の30%~40%"],"QualityItem":"金ﾆｽ塗布確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示箇所に塗布されている事","Method":"目視","RecordMethod":"-","Other":"金ﾆｽ","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"ﾓｰﾀｰﾌﾞﾗｹｯﾄ組立","WorkItems":["◆1. MOTOR-BRACKET の下面及び左側面以外の外周りの加工面に金ﾆｽを塗装する","◆2. BEARING にｸﾞﾘｰｽをいれIﾏｰｸを合わせる","3. 2完成品にPLATE をBOLT で締結する"],"WorkPoints":["･BEARING ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝｸﾞはﾏｰｸを合わせ､MOTOR-BRACKET に挿入する(正面合わせ､刻印あわせ)","挿入時方向に注意する","取付け後､隙間を確認(0.01㎜以上)","塗布禁止場所(ﾓｰﾀｰ取付け面､ﾌﾚｰﾑ取付け面)","この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["刻印を合わせる","印4箇所の隙間があるかﾁｪｯｸする(隙間が無いときはﾘｰﾀﾞｰへ)","左側面","下面","空間容積の30%~40%"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"ﾓｰﾀｰﾌﾞﾗｹｯﾄ組立","WorkItems":["◆1. MOTOR-BRACKET の下面及び左側面以外の外周りの加工面に金ﾆｽを塗装する","◆2. BEARING にｸﾞﾘｰｽをいれIﾏｰｸを合わせる","3. 2完成品にPLATE をBOLT で締結する"],"WorkPoints":["･BEARING ｱﾝｷﾞｭﾗﾍﾞｱﾘﾝｸﾞはﾏｰｸを合わせ､MOTOR-BRACKET に挿入する(正面合わせ､刻印あわせ)","挿入時方向に注意する","取付け後､隙間を確認(0.01㎜以上)","塗布禁止場所(ﾓｰﾀｰ取付け面､ﾌﾚｰﾑ取付け面)","この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["刻印を合わせる","印4箇所の隙間があるかﾁｪｯｸする(隙間が無いときはﾘｰﾀﾞｰへ)","左側面","下面","空間容積の30%~40%"],"QualityItem":"塗布量","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"空間容積の30%~40%","Method":"目視","RecordMethod":"-","Other":"ｸﾞﾘｰｽLCG100","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｼｯｸﾈｽｹﾞｰｼﾞ","Size":"0.01㎜","ToolOther":"","WorkName":"ﾓｰﾀｰﾌﾞﾗｹｯﾄ組立","WorkItems":["3. 2完成品にPLATE をBOLT で締結する"],"WorkPoints":["挿入時方向に注意する","取付け後､隙間を確認(0.01㎜以上)","塗布禁止場所(ﾓｰﾀｰ取付け面､ﾌﾚｰﾑ取付け面)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["刻印を合わせる","印4箇所の隙間があるかﾁｪｯｸする(隙間が無いときはﾘｰﾀﾞｰへ)","◆作業者安全作業"]} | {"WorkTypes":[],"ToolName":"ｼｯｸﾈｽｹﾞｰｼﾞ","Size":"0.01㎜","ToolOther":"","WorkName":"ﾓｰﾀｰﾌﾞﾗｹｯﾄ組立","WorkItems":["3. 2完成品にPLATE をBOLT で締結する"],"WorkPoints":["挿入時方向に注意する","取付け後､隙間を確認(0.01㎜以上)","塗布禁止場所(ﾓｰﾀｰ取付け面､ﾌﾚｰﾑ取付け面)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["刻印を合わせる","印4箇所の隙間があるかﾁｪｯｸする(隙間が無いときはﾘｰﾀﾞｰへ)","◆作業者安全作業"],"QualityItem":"隙間確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"隙間:0.01㎜以下","Method":"ｼｯｸﾈｽｹﾞｰｼﾞ","RecordMethod":"-","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｼｯｸﾈｽｹﾞｰｼﾞ","Size":"0.01㎜","ToolOther":"","WorkName":"ﾓｰﾀｰﾌﾞﾗｹｯﾄ組込み","WorkItems":["1. のﾎﾞｰﾙﾈｼﾞにSTOPPER を挿入する","2. 1完成品に を挿入しBOLT で締結する"],"WorkPoints":["挿入時ﾋﾟﾝに当てながらﾎﾞｰﾙねじ部がｽﾑｰｽﾞに挿入できること(ﾋﾟﾝとの隙間:0.01㎜以下)","この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["隙間無き様取付け","ﾌﾚｰﾑの裏から取付け"]} | {"WorkTypes":[],"ToolName":"ｼｯｸﾈｽｹﾞｰｼﾞ","Size":"0.01㎜","ToolOther":"","WorkName":"ﾓｰﾀｰﾌﾞﾗｹｯﾄ組込み","WorkItems":["1. のﾎﾞｰﾙﾈｼﾞにSTOPPER を挿入する","2. 1完成品に を挿入しBOLT で締結する"],"WorkPoints":["挿入時ﾋﾟﾝに当てながらﾎﾞｰﾙねじ部がｽﾑｰｽﾞに挿入できること(ﾋﾟﾝとの隙間:0.01㎜以下)","この作業では､P1用､P2用の 2個を作成の事(ｵﾌﾟｼｮﾝ･個別仕様によりP2無しの仕様有)"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["隙間無き様取付け","ﾌﾚｰﾑの裏から取付け"],"QualityItem":"隙間確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"隙間:0.01㎜以下","Method":"ｼｯｸﾈｽｹﾞｰｼﾞ","RecordMethod":"-","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸｽﾊﾟﾅ","Size":"","ToolOther":"","WorkName":"H軸ﾎﾞｰﾙねじ芯出し","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WWYJ-5300-062"]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸｽﾊﾟﾅ","Size":"","ToolOther":"","WorkName":"H軸ﾎﾞｰﾙねじ芯出し","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WWYJ-5300-062"],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"10N･m±10%","Method":"ﾄﾙｸｽﾊﾟﾅ","RecordMethod":"WWYJ-5300-062","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ","Size":"","ToolOther":"","WorkName":"ﾎﾞｰﾙねじ芯振れ確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WWYJ-5300-062"]} | {"WorkTypes":[],"ToolName":"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ","Size":"","ToolOther":"","WorkName":"ﾎﾞｰﾙねじ芯振れ確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WWYJ-5300-062"],"QualityItem":"芯ﾌﾞﾚ確認","ToolManageNo":"-","ToolCycle":"1回/半年","ToolRecord":"校正成績書","StdVal":"10μm以下","Method":"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ","RecordMethod":"WWYJ-5300-062","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ","Size":"","ToolOther":"","WorkName":"ﾎﾞｰﾙねじｽﾗｽﾄｶﾞﾀ確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WWYJ-5300-062"]} | {"WorkTypes":[],"ToolName":"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ","Size":"","ToolOther":"","WorkName":"ﾎﾞｰﾙねじｽﾗｽﾄｶﾞﾀ確認","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WWYJ-5300-062"],"QualityItem":"ｽﾗｽﾄ確認","ToolManageNo":"-","ToolCycle":"1回/半年","ToolRecord":"校正成績書","StdVal":"ｶﾞﾀ5μm以下","Method":"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ","RecordMethod":"WWYJ-5300-062","Other":"-","ProcessNames":["作業者安全工程"]} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.