input stringclasses 1 value | instruction stringlengths 181 1.31k | output stringlengths 329 1.48k | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付2(ﾌﾛﾝﾄｶﾊﾞｰ)","WorkItems":["■2. にLABEL LABEL を貼付ける","■1. LABEL LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:LABEL PW0102M1､LABEL PC013901"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表 :安全部品確認","検査表 :貼付位置確認","WWYJ-5300-025"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付2(ﾌﾛﾝﾄｶﾊﾞｰ)","WorkItems":["■2. にLABEL LABEL を貼付ける","■1. LABEL LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:LABEL PW0102M1､LABEL PC013901"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表 :安全部品確認","検査表 :貼付位置確認","WWYJ-5300-025"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-025","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"1000㎜","ToolOther":"","WorkName":"銘板貼付2(ﾌﾛﾝﾄｶﾊﾞｰ)","WorkItems":["■2. にLABEL LABEL を貼付ける","■1. LABEL LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:LABEL PW0102M1､LABEL PC013901"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表 :安全部品確認","検査表 :貼付位置確認","■安全作業"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"1000㎜","ToolOther":"","WorkName":"銘板貼付2(ﾌﾛﾝﾄｶﾊﾞｰ)","WorkItems":["■2. にLABEL LABEL を貼付ける","■1. LABEL LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:LABEL PW0102M1､LABEL PC013901"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表 :安全部品確認","検査表 :貼付位置確認","■安全作業"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付3(前面下ｶﾊﾞｰ)","WorkItems":["■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:PC010201","2ｾｯﾄ貼付け"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","KT4","図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付","WWYJ-5300-025"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付3(前面下ｶﾊﾞｰ)","WorkItems":["■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:PC010201","2ｾｯﾄ貼付け"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","KT4","図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付","WWYJ-5300-025"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-025","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付3(前面下ｶﾊﾞｰ)","WorkItems":["■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:PC010201","2ｾｯﾄ貼付け"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","KT4","図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付","■安全作業"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付3(前面下ｶﾊﾞｰ)","WorkItems":["■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:PC010201","2ｾｯﾄ貼付け"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","KT4","図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付","■安全作業"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付4(前面下ｶﾊﾞｰ左)","WorkItems":["1. にLABEL を貼付ける"],"WorkPoints":["貼付前に脱脂する事"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付4(前面下ｶﾊﾞｰ左)","WorkItems":["1. にLABEL を貼付ける"],"WorkPoints":["貼付前に脱脂する事"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付5(後面ｶﾊﾞｰ)","WorkItems":["3. 2.完成品にｼﾘｱﾙNo.ﾗﾍﾞﾙを貼付ける","■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:PD0101M1","ｼﾘｱﾙNo.ﾗﾍﾞﾙは､生産管理にて作成","ｼﾘｱﾙNo."],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","WWYJ-5300-025"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付5(後面ｶﾊﾞｰ)","WorkItems":["3. 2.完成品にｼﾘｱﾙNo.ﾗﾍﾞﾙを貼付ける","■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:PD0101M1","ｼﾘｱﾙNo.ﾗﾍﾞﾙは､生産管理にて作成","ｼﾘｱﾙNo."],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","WWYJ-5300-025"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-025","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付5(後面ｶﾊﾞｰ)","WorkItems":["3. 2.完成品にｼﾘｱﾙNo.ﾗﾍﾞﾙを貼付ける","■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする","3. 2.完成品にｼﾘｱﾙNo.ﾗﾍﾞﾙを貼付ける","■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","貼付前に脱脂する事"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","■安全作業","検査表LABEL :安全部品確認"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付5(後面ｶﾊﾞｰ)","WorkItems":["3. 2.完成品にｼﾘｱﾙNo.ﾗﾍﾞﾙを貼付ける","■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする","3. 2.完成品にｼﾘｱﾙNo.ﾗﾍﾞﾙを貼付ける","■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","貼付前に脱脂する事"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","■安全作業","検査表LABEL :安全部品確認"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付5(後面ｶﾊﾞｰ)","WorkItems":["3. 2.完成品にｼﾘｱﾙNo.ﾗﾍﾞﾙを貼付ける","■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする","3. 2.完成品にｼﾘｱﾙNo.ﾗﾍﾞﾙを貼付ける","■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","貼付前に脱脂する事"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","■安全作業","検査表LABEL :安全部品確認"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付5(後面ｶﾊﾞｰ)","WorkItems":["3. 2.完成品にｼﾘｱﾙNo.ﾗﾍﾞﾙを貼付ける","■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする","3. 2.完成品にｼﾘｱﾙNo.ﾗﾍﾞﾙを貼付ける","■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","貼付前に脱脂する事"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","■安全作業","検査表LABEL :安全部品確認"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付6(後面下ｶﾊﾞｰ)","WorkItems":["■2. COVER COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:PC010201"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","KT4","図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付","WWYJ-5300-025"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付6(後面下ｶﾊﾞｰ)","WorkItems":["■2. COVER COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:PC010201"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","KT4","図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付","WWYJ-5300-025"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-025","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付6(後面下ｶﾊﾞｰ)","WorkItems":["■2. COVER COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:PC010201"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","KT4","図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付","■安全作業"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付6(後面下ｶﾊﾞｰ)","WorkItems":["■2. COVER COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:PC010201"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","KT4","図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付","■安全作業"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付7(右側面架台下ｶﾊﾞｰ)","WorkItems":["■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式(品番):N210121728AA"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付","MA14","WWYJ-5300-025"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付7(右側面架台下ｶﾊﾞｰ)","WorkItems":["■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式(品番):N210121728AA"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付","MA14","WWYJ-5300-025"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-025","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付7(右側面架台下ｶﾊﾞｰ)","WorkItems":["■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式(品番):N210121728AA"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付","MA14","■安全作業"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付7(右側面架台下ｶﾊﾞｰ)","WorkItems":["■2. COVER にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式(品番):N210121728AA"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付","MA14","■安全作業"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"1000㎜","ToolOther":"","WorkName":"銘板貼付8(右側面架台下ｶﾊﾞｰ)","WorkItems":["1. にLABEL LABEL を貼付ける"],"WorkPoints":["貼付前に脱脂する事","標準仕様"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"1000㎜","ToolOther":"","WorkName":"銘板貼付8(右側面架台下ｶﾊﾞｰ)","WorkItems":["1. にLABEL LABEL を貼付ける"],"WorkPoints":["貼付前に脱脂する事","標準仕様"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付9(前部開閉扉右側)","WorkItems":["■2. FRAME-KIT にLABEL LABEL LABEL を貼付ける","■1. LABEL LABEL LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:LABEL PD0101M1 LABEL PC010101 LABEL PC011701"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","WWYJ-5300-025"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付9(前部開閉扉右側)","WorkItems":["■2. FRAME-KIT にLABEL LABEL LABEL を貼付ける","■1. LABEL LABEL LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:LABEL PD0101M1 LABEL PC010101 LABEL PC011701"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","WWYJ-5300-025"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-025","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付9(前部開閉扉右側)","WorkItems":["■2. FRAME-KIT にLABEL LABEL LABEL を貼付ける","■1. LABEL LABEL LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:LABEL PD0101M1 LABEL PC010101 LABEL PC011701"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","■安全作業"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付9(前部開閉扉右側)","WorkItems":["■2. FRAME-KIT にLABEL LABEL LABEL を貼付ける","■1. LABEL LABEL LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:LABEL PD0101M1 LABEL PC010101 LABEL PC011701"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","■安全作業"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付10(前部開閉扉右側)","WorkItems":["2. にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表 :安全部品確認",">PC<",">PC<","WWYJ-5300-015"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付10(前部開閉扉右側)","WorkItems":["2. にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表 :安全部品確認",">PC<",">PC<","WWYJ-5300-015"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-015","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付10(前部開閉扉右側)","WorkItems":["2. にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表 :安全部品確認",">PC<",">PC<","■安全作業"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付10(前部開閉扉右側)","WorkItems":["2. にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表 :安全部品確認",">PC<",">PC<","■安全作業"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付11(前部開閉扉左側)","WorkItems":["■2. FRAME-KIT にLABEL LABEL LABEL を貼付ける","■1. LABEL LABEL LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:LABEL PD0101M1 LABEL PC010101 LABEL PC011701"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","WWYJ-5300-025"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付11(前部開閉扉左側)","WorkItems":["■2. FRAME-KIT にLABEL LABEL LABEL を貼付ける","■1. LABEL LABEL LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:LABEL PD0101M1 LABEL PC010101 LABEL PC011701"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","WWYJ-5300-025"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-025","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付11(前部開閉扉左側)","WorkItems":["■2. FRAME-KIT にLABEL LABEL LABEL を貼付ける","■1. LABEL LABEL LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:LABEL PD0101M1 LABEL PC010101 LABEL PC011701"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","■安全作業"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付11(前部開閉扉左側)","WorkItems":["■2. FRAME-KIT にLABEL LABEL LABEL を貼付ける","■1. LABEL LABEL LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:LABEL PD0101M1 LABEL PC010101 LABEL PC011701"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認","検査表LABEL :貼付位置確認","■安全作業"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付12(前部開閉扉左側)","WorkItems":["2. にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表 :安全部品確認",">PC<",">PC<","WWYJ-5300-015"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付12(前部開閉扉左側)","WorkItems":["2. にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表 :安全部品確認",">PC<",">PC<","WWYJ-5300-015"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-015","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付12(前部開閉扉左側)","WorkItems":["2. にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表 :安全部品確認",">PC<",">PC<","■安全作業"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付12(前部開閉扉左側)","WorkItems":["2. にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表 :安全部品確認",">PC<",">PC<","■安全作業"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付13(前面上部)","WorkItems":["2. COVER にLABEL LABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","WWYJ-5300-015"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付13(前面上部)","WorkItems":["2. COVER にLABEL LABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","WWYJ-5300-015"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-015","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"1000㎜","ToolOther":"","WorkName":"銘板貼付13(前面上部)","WorkItems":["2. COVER にLABEL LABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","■安全作業"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"1000㎜","ToolOther":"","WorkName":"銘板貼付13(前面上部)","WorkItems":["2. COVER にLABEL LABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","■安全作業"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付14(後面上部)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","WWYJ-5300-015"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付14(後面上部)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","WWYJ-5300-015"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-015","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付14(後面上部)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","■安全作業"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付14(後面上部)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","■安全作業"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付15(後面中央左右)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認","2ｾｯﾄ","2ｾｯﾄ作成","穴位置寸法が違います"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","WWYJ-5300-015"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付15(後面中央左右)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認","2ｾｯﾄ","2ｾｯﾄ作成","穴位置寸法が違います"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","WWYJ-5300-015"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-015","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付15(後面中央左右)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認","2ｾｯﾄ","2ｾｯﾄ作成","穴位置寸法が違います"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","■安全作業"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付15(後面中央左右)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認","2ｾｯﾄ","2ｾｯﾄ作成","穴位置寸法が違います"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","■安全作業"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付16(ﾒﾝﾃﾅﾝｽｶﾊﾞｰ)","WorkItems":["2. COVER-KIT にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認","取手の横に穴あり"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","WWYJ-5300-015"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付16(ﾒﾝﾃﾅﾝｽｶﾊﾞｰ)","WorkItems":["2. COVER-KIT にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認","取手の横に穴あり"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","WWYJ-5300-015"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-015","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付16(ﾒﾝﾃﾅﾝｽｶﾊﾞｰ)","WorkItems":["2. COVER-KIT にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認","取手の横に穴あり"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","■安全作業"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付16(ﾒﾝﾃﾅﾝｽｶﾊﾞｰ)","WorkItems":["2. COVER-KIT にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認","取手の横に穴あり"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","■安全作業"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付17(ﾒﾝﾃﾅﾝｽｶﾊﾞｰ)","WorkItems":["■2. にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:PC010101"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表 :安全部品確認","検査表 :貼付位置確認","WWYJ-5300-025"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付17(ﾒﾝﾃﾅﾝｽｶﾊﾞｰ)","WorkItems":["■2. にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:PC010101"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表 :安全部品確認","検査表 :貼付位置確認","WWYJ-5300-025"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-025","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付17(ﾒﾝﾃﾅﾝｽｶﾊﾞｰ)","WorkItems":["■2. にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:PC010101"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表 :安全部品確認","検査表 :貼付位置確認","■安全作業"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付17(ﾒﾝﾃﾅﾝｽｶﾊﾞｰ)","WorkItems":["■2. にLABEL を貼付ける","■1. LABEL の型式確認をする"],"WorkPoints":["貼付前に脱脂する事","±2㎜以下","型式:PC010101"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表 :安全部品確認","検査表 :貼付位置確認","■安全作業"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付18(天井面前側)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","WWYJ-5300-015"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付18(天井面前側)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","WWYJ-5300-015"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-015","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付18(天井面前側)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","■安全作業"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付18(天井面前側)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","■安全作業"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付19(天井面中央側左右)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認","左側","右側","穴位置に注意する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<",">PC<","WWYJ-5300-015"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付19(天井面中央側左右)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認","左側","右側","穴位置に注意する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<",">PC<","WWYJ-5300-015"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-015","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付19(天井面中央側左右)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認","左側","右側","穴位置に注意する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<",">PC<","■安全作業"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付19(天井面中央側左右)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認","左側","右側","穴位置に注意する"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<",">PC<","■安全作業"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付20(天井面後側)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","WWYJ-5300-015"]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"銘板貼付20(天井面後側)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","WWYJ-5300-015"],"QualityItem":"型式確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"型式が一致する事","Method":"目視","RecordMethod":"WWYJ-5300-015","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付20(天井面後側)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","■安全作業"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"銘板貼付20(天井面後側)","WorkItems":["2. COVER にLABEL を貼付ける","■1. LABEL の型式を確認する"],"WorkPoints":["貼付前に脱脂する事","記述内容確認"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["検査表LABEL :安全部品確認",">PC<","■安全作業"],"QualityItem":"貼付確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±2㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":["安全工程"]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立①","WorkItems":["2. 1.完成品にSUPPORT NUT NUT を取付け","1. FRAME にCAP を両端面に取付け"],"WorkPoints":["上面","右面","外面","左面","外面","内面","右面","外面","左面","上面","内面","SUPPORT はNUT NUT とｾｯﾄで使用"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ","NUT N011:M4後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立①","WorkItems":["2. 1.完成品にSUPPORT NUT NUT を取付け","1. FRAME にCAP を両端面に取付け"],"WorkPoints":["上面","右面","外面","左面","外面","内面","右面","外面","左面","上面","内面","SUPPORT はNUT NUT とｾｯﾄで使用"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ","NUT N011:M4後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立②","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["左面","上面","外面","内面","外面","内面","下面","外面","左面","上面","SUPPORT はNUT NUT とｾｯﾄで使用","下面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ","NUT N011:M4後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立②","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["左面","上面","外面","内面","外面","内面","下面","外面","左面","上面","SUPPORT はNUT NUT とｾｯﾄで使用","下面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ","NUT N011:M4後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立③","WorkItems":["1. にBRACKET をWASHER BOLT で取付け"],"WorkPoints":["左面","上面","外面","外面"," とBRACKET の端面を合わせる","内面","下面","外面","左面","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立③","WorkItems":["1. にBRACKET をWASHER BOLT で取付け"],"WorkPoints":["左面","上面","外面","外面"," とBRACKET の端面を合わせる","内面","下面","外面","左面","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立④","WorkItems":["1. FRAME にSUPPORT NUT NUT CABLE-SUPPORT を取付け"],"WorkPoints":["左面","上面","外面","外面","SUPPORT はNUT NUT とｾｯﾄで使用","下面","内面","内面","下面","外面","左面","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ","NUT N011:M4後入れ","CABLE-SUPPORT N601"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立④","WorkItems":["1. FRAME にSUPPORT NUT NUT CABLE-SUPPORT を取付け"],"WorkPoints":["左面","上面","外面","外面","SUPPORT はNUT NUT とｾｯﾄで使用","下面","内面","内面","下面","外面","左面","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ","NUT N011:M4後入れ","CABLE-SUPPORT N601"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立⑤","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["左面","外面","外面"," とBRACKET の端面を合わせる","内面","下面","外面","左面","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立⑤","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["左面","外面","外面"," とBRACKET の端面を合わせる","内面","下面","外面","左面","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立⑥","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["左面","外面","外面","SUPPORT はNUT NUT とｾｯﾄで使用","下面","内面","内面","下面","外面","左面","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ","NUT N011:M4後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立⑥","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["左面","外面","外面","SUPPORT はNUT NUT とｾｯﾄで使用","下面","内面","内面","下面","外面","左面","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ","NUT N011:M4後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立⑦","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["左面","外面","外面"," とBRACKET の端面を合わせる","内面","下面","外面","左面","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立⑦","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["左面","外面","外面"," とBRACKET の端面を合わせる","内面","下面","外面","左面","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立⑧","WorkItems":["1. FRAME にSUPPORT NUT を取付け"],"WorkPoints":["左面","上面","外面","SUPPORT はNUT とｾｯﾄで使用","内面","内面","下面","外面","左面","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立⑧","WorkItems":["1. FRAME にSUPPORT NUT を取付け"],"WorkPoints":["左面","上面","外面","SUPPORT はNUT とｾｯﾄで使用","内面","内面","下面","外面","左面","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立⑨","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["左面","外面","外面"," とBRACKET の端面を合わせる","内面","下面","外面","左面","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立⑨","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["左面","外面","外面"," とBRACKET の端面を合わせる","内面","下面","外面","左面","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"1000㎜","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立⑩","WorkItems":["1. をWASHER BOLT で取付"],"WorkPoints":["外面"," と の端面を合わせる","全て内面側を㉗側にして合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["170mm","765mm","290mm","35mm"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"1000㎜","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立⑩","WorkItems":["1. をWASHER BOLT で取付"],"WorkPoints":["外面"," と の端面を合わせる","全て内面側を㉗側にして合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["170mm","765mm","290mm","35mm"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±0.5㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立⑩","WorkItems":["1. をWASHER BOLT で取付"],"WorkPoints":["外面"," と の端面を合わせる","全て内面側を㉗側にして合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["170mm","765mm","290mm","35mm"]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ正面側組立⑩","WorkItems":["1. をWASHER BOLT で取付"],"WorkPoints":["外面"," と の端面を合わせる","全て内面側を㉗側にして合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["170mm","765mm","290mm","35mm"],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立①","WorkItems":["2. 1.完成品にSUPPORT NUT NUT を取付け","1. FRAME にCAP を両端面に取付け"],"WorkPoints":["上面","右面","外面","左面","外面","内面","右面","外面","左面","上面","内面","SUPPORT はNUT NUT とｾｯﾄで使用"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ","NUT N011:M4後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立①","WorkItems":["2. 1.完成品にSUPPORT NUT NUT を取付け","1. FRAME にCAP を両端面に取付け"],"WorkPoints":["上面","右面","外面","左面","外面","内面","右面","外面","左面","上面","内面","SUPPORT はNUT NUT とｾｯﾄで使用"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ","NUT N011:M4後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立②","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["右面","上面","外面","内面","外面","内面","下面","外面","右面","上面","SUPPORT はNUT NUT とｾｯﾄで使用","下面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ","NUT N011:M4後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立②","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["右面","上面","外面","内面","外面","内面","下面","外面","右面","上面","SUPPORT はNUT NUT とｾｯﾄで使用","下面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ","NUT N011:M4後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立③","WorkItems":["1. にBRACKET をWASHER BOLT で取付け"],"WorkPoints":["右面","上面","外面","外面","内面","下面","外面","右面","上面"," とBRACKET の端面を合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立③","WorkItems":["1. にBRACKET をWASHER BOLT で取付け"],"WorkPoints":["右面","上面","外面","外面","内面","下面","外面","右面","上面"," とBRACKET の端面を合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立④","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["右面","上面","外面","外面","SUPPORT はNUT NUT とｾｯﾄで使用","下面","内面","内面","下面","外面","右面","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ","NUT N011:M4後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立④","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["右面","上面","外面","外面","SUPPORT はNUT NUT とｾｯﾄで使用","下面","内面","内面","下面","外面","右面","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ","NUT N011:M4後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立⑤","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["右面","外面","外面"," とBRACKET の端面を合わせる","内面","下面","外面","右面","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立⑤","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["右面","外面","外面"," とBRACKET の端面を合わせる","内面","下面","外面","右面","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立⑥","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["右面","外面","外面","SUPPORT はNUT NUT とｾｯﾄで使用","下面","内面","下面","外面","右面","上面","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ","NUT N011:M4後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立⑥","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["右面","外面","外面","SUPPORT はNUT NUT とｾｯﾄで使用","下面","内面","下面","外面","右面","上面","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ","NUT N011:M4後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立⑦","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["右面","外面","外面"," とBRACKET の端面を合わせる","内面","下面","外面","右面","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立⑦","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["右面","外面","外面"," とBRACKET の端面を合わせる","内面","下面","外面","右面","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立⑧","WorkItems":["1. FRAME にSUPPORT NUT を取付け"],"WorkPoints":["右面","上面","外面","SUPPORT はNUT とｾｯﾄで使用","内面","内面","下面","外面","右面","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立⑧","WorkItems":["1. FRAME にSUPPORT NUT を取付け"],"WorkPoints":["右面","上面","外面","SUPPORT はNUT とｾｯﾄで使用","内面","内面","下面","外面","右面","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N010:M6後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立⑨","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["外面","外面","内面","下面","外面","右面","上面"," とBRACKET の端面を合わせる","右面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立⑨","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["外面","外面","内面","下面","外面","右面","上面"," とBRACKET の端面を合わせる","右面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"1000㎜","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立⑩","WorkItems":["1. をWASHER BOLT で取付"],"WorkPoints":["外面"," と の端面を合わせる","全て内面側を㉗側にして合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["475mm","480mm","240mm","35mm"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"1000㎜","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立⑩","WorkItems":["1. をWASHER BOLT で取付"],"WorkPoints":["外面"," と の端面を合わせる","全て内面側を㉗側にして合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["475mm","480mm","240mm","35mm"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±0.5㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立⑩","WorkItems":["1. をWASHER BOLT で取付"],"WorkPoints":["外面"," と の端面を合わせる","全て内面側を㉗側にして合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["475mm","480mm","240mm","35mm"]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ後面側組立⑩","WorkItems":["1. をWASHER BOLT で取付"],"WorkPoints":["外面"," と の端面を合わせる","全て内面側を㉗側にして合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["475mm","480mm","240mm","35mm"],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立①","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["正面方向","右面","底面","左面","底面","内面","右面","底面","左面","正面方向","内面","SUPPORT はNUT NUT とｾｯﾄで使用","正面方向"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立①","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["正面方向","右面","底面","左面","底面","内面","右面","底面","左面","正面方向","内面","SUPPORT はNUT NUT とｾｯﾄで使用","正面方向"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立②","WorkItems":["1. にBRACKET をWASHER BOLT で取付け","2. 1.完成品に④をWASHER ⑰で取付け","1. にBRACKET をWASHER BOLT で取付け","2. 1.完成品に④をWASHER ⑰で取付け"],"WorkPoints":[],"Tolks":["締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立②","WorkItems":["1. にBRACKET をWASHER BOLT で取付け","2. 1.完成品に④をWASHER ⑰で取付け","1. にBRACKET をWASHER BOLT で取付け","2. 1.完成品に④をWASHER ⑰で取付け"],"WorkPoints":[],"Tolks":["締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立③","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["正面方向","右面","底面","左面","底面","内面","右面","底面","左面","正面方向","内面","SUPPORT はNUT NUT とｾｯﾄで使用","正面方向"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立③","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["正面方向","右面","底面","左面","底面","内面","右面","底面","左面","正面方向","内面","SUPPORT はNUT NUT とｾｯﾄで使用","正面方向"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立④","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["左側","後面","底面","正面","底面","内面","SUPPORT はNUT NUT とｾｯﾄで使用","左側","左側","内面","正面","底面","後面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立④","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["左側","後面","底面","正面","底面","内面","SUPPORT はNUT NUT とｾｯﾄで使用","左側","左側","内面","正面","底面","後面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑤","WorkItems":["1. にBRACKET をWASHER BOLT で取付け","2. 1.完成品にBRACKET をWASHER BOLT で取付け","1. にBRACKET をWASHER BOLT で取付け","2. 1.完成品にBRACKET をWASHER BOLT で取付け"],"WorkPoints":["左側","底面","底面","左側","左側","内面","正面","底面","後面"," とBRACKET の端面を合わせる","内面","左側","底面","底面","左側","左側","内面","正面","底面","後面"," とBRACKET の端面を合わせる","内面"],"Tolks":["締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑤","WorkItems":["1. にBRACKET をWASHER BOLT で取付け","2. 1.完成品にBRACKET をWASHER BOLT で取付け","1. にBRACKET をWASHER BOLT で取付け","2. 1.完成品にBRACKET をWASHER BOLT で取付け"],"WorkPoints":["左側","底面","底面","左側","左側","内面","正面","底面","後面"," とBRACKET の端面を合わせる","内面","左側","底面","底面","左側","左側","内面","正面","底面","後面"," とBRACKET の端面を合わせる","内面"],"Tolks":["締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑥","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["左面","後面","底面","正面","底面","内面","SUPPORT はNUT NUT とｾｯﾄで使用","左面","左面","内面","正面","底面","後面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑥","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["左面","後面","底面","正面","底面","内面","SUPPORT はNUT NUT とｾｯﾄで使用","左面","左面","内面","正面","底面","後面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑦","WorkItems":["1. にBRACKET をWASHER BOLT で取付け"],"WorkPoints":["左面","底面","底面","左面","左面","内面","正面","底面","後面"," とBRACKET の端面を合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑦","WorkItems":["1. にBRACKET をWASHER BOLT で取付け"],"WorkPoints":["左面","底面","底面","左面","左面","内面","正面","底面","後面"," とBRACKET の端面を合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑧","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["左面","後面","底面","正面","底面","内面","SUPPORT はNUT NUT とｾｯﾄで使用","左面","左面","内面","正面","底面","後面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑧","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["左面","後面","底面","正面","底面","内面","SUPPORT はNUT NUT とｾｯﾄで使用","左面","左面","内面","正面","底面","後面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑨","WorkItems":["1. にBRACKET をWASHER BOLT で取付け"],"WorkPoints":["左面","底面","底面","左面","左面","内面","正面","底面","後面"," とBRACKET の端面を合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑨","WorkItems":["1. にBRACKET をWASHER BOLT で取付け"],"WorkPoints":["左面","底面","底面","左面","左面","内面","正面","底面","後面"," とBRACKET の端面を合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑩","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["左面","後面","底面","正面","底面","内面","SUPPORT はNUT NUT とｾｯﾄで使用","左面","左面","内面","正面","底面","後面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑩","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["左面","後面","底面","正面","底面","内面","SUPPORT はNUT NUT とｾｯﾄで使用","左面","左面","内面","正面","底面","後面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑪","WorkItems":["1. にBRACKET をWASHER BOLT で取付け","2. 1.完成品にBRACKET をWASHER BOLT で取付け","1. にBRACKET をWASHER BOLT で取付け","2. 1.完成品にBRACKET をWASHER BOLT で取付け"],"WorkPoints":["左面","底面","底面","左面","左面","内面","正面","底面","後面"," とBRACKET の端面を合わせる","内面","左面","底面","底面","左面","左面","内面","正面","底面","後面"," とBRACKET の端面を合わせる","内面"],"Tolks":["締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑪","WorkItems":["1. にBRACKET をWASHER BOLT で取付け","2. 1.完成品にBRACKET をWASHER BOLT で取付け","1. にBRACKET をWASHER BOLT で取付け","2. 1.完成品にBRACKET をWASHER BOLT で取付け"],"WorkPoints":["左面","底面","底面","左面","左面","内面","正面","底面","後面"," とBRACKET の端面を合わせる","内面","左面","底面","底面","左面","左面","内面","正面","底面","後面"," とBRACKET の端面を合わせる","内面"],"Tolks":["締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m","締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"1000㎜","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑫","WorkItems":["1. をWASHER BOLT で取付"],"WorkPoints":["底面"," と の端面を合わせる","全て内面側を㉗側にして合わせる"," と の端面を合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["405mm","472mm","405mm","30mm","30mm","30mm","30mm"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"1000㎜","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑫","WorkItems":["1. をWASHER BOLT で取付"],"WorkPoints":["底面"," と の端面を合わせる","全て内面側を㉗側にして合わせる"," と の端面を合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["405mm","472mm","405mm","30mm","30mm","30mm","30mm"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±0.5㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑫","WorkItems":["1. をWASHER BOLT で取付"],"WorkPoints":["底面"," と の端面を合わせる","全て内面側を㉗側にして合わせる"," と の端面を合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["405mm","472mm","405mm","30mm","30mm","30mm","30mm"]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ底面側組立⑫","WorkItems":["1. をWASHER BOLT で取付"],"WorkPoints":["底面"," と の端面を合わせる","全て内面側を㉗側にして合わせる"," と の端面を合わせる"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["405mm","472mm","405mm","30mm","30mm","30mm","30mm"],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ上面側組立①","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["左面","上面","前面","上面","SUPPORT はNUT NUT とｾｯﾄで使用","下面","後面","後面","下面","前面","左面","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ上面側組立①","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["左面","上面","前面","上面","SUPPORT はNUT NUT とｾｯﾄで使用","下面","後面","後面","下面","前面","左面","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ上面側組立②","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["左面","上面"," とBRACKET の端面を合わせる","上面","後面","下面","前面","左面","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ上面側組立②","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["左面","上面"," とBRACKET の端面を合わせる","上面","後面","下面","前面","左面","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ左面側組立①","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["後側","上面","左面","左面","SUPPORT はNUT NUT とｾｯﾄで使用","下面","右面","右面","下面","左面","後側","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ左面側組立①","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["後側","上面","左面","左面","SUPPORT はNUT NUT とｾｯﾄで使用","下面","右面","右面","下面","左面","後側","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ左面側組立②","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["後側","左面"," とBRACKET の端面を合わせる","左面","右面","下面","左面","後側","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ左面側組立②","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["後側","左面"," とBRACKET の端面を合わせる","左面","右面","下面","左面","後側","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ左面側組立③","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["後側","上面","左面","左面","SUPPORT はNUT NUT とｾｯﾄで使用","下面","右面","後側","右面","上面","左面","下面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ左面側組立③","WorkItems":["1. FRAME にSUPPORT NUT NUT を取付け"],"WorkPoints":["後側","上面","左面","左面","SUPPORT はNUT NUT とｾｯﾄで使用","下面","右面","後側","右面","上面","左面","下面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ","NUT N012:M4後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ左面側組立④","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["後側","左面"," とBRACKET の端面を合わせる","左面","後側","右面","上面","左面","下面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ左面側組立④","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["後側","左面"," とBRACKET の端面を合わせる","左面","後側","右面","上面","左面","下面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ左面側組立⑤","WorkItems":["1. FRAME にSUPPORT NUT を取付け"],"WorkPoints":["後側","上面","左面","左面","SUPPORT はNUT とｾｯﾄで使用","下面","右面","右面","下面","左面","後側","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ"]} | {"WorkTypes":[],"ToolName":"ｺﾝﾍﾞｯｸｽ","Size":"2m","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ左面側組立⑤","WorkItems":["1. FRAME にSUPPORT NUT を取付け"],"WorkPoints":["後側","上面","左面","左面","SUPPORT はNUT とｾｯﾄで使用","下面","右面","右面","下面","左面","後側","上面"],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["NUT N006:M6後入れ"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±1㎜","Method":"ｺﾝﾍﾞｯｸｽ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ左面側組立⑥","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["後側","左面"," とBRACKET の端面を合わせる","左面","右面","下面","左面","後側","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ左面側組立⑥","WorkItems":["1. にBRACKET をWASHER BOLT で取付"],"WorkPoints":["後側","左面"," とBRACKET の端面を合わせる","左面","右面","下面","左面","後側","上面"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ全体組立①","WorkItems":["1. と をWASHER BOLT BOLT で取付"],"WorkPoints":["正面"," の底面を下にして を の内面側に取付ける","下から見た図"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["5mm"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ全体組立①","WorkItems":["1. と をWASHER BOLT BOLT で取付"],"WorkPoints":["正面"," の底面を下にして を の内面側に取付ける","下から見た図"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["5mm"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±0.5㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ全体組立①","WorkItems":["1. と をWASHER BOLT BOLT で取付"],"WorkPoints":["正面"," の底面を下にして を の内面側に取付ける","下から見た図"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["5mm"]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ全体組立①","WorkItems":["1. と をWASHER BOLT BOLT で取付"],"WorkPoints":["正面"," の底面を下にして を の内面側に取付ける","下から見た図"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["5mm"],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ全体組立②","WorkItems":["1. と をWASHER BOLT BOLT で取付"],"WorkPoints":["後面"," の底面を下にして を の内面側に取付ける","下から見た図"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["5mm"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ全体組立②","WorkItems":["1. と をWASHER BOLT BOLT で取付"],"WorkPoints":["後面"," の底面を下にして を の内面側に取付ける","下から見た図"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["5mm"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±0.5㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ全体組立②","WorkItems":["1. と をWASHER BOLT BOLT で取付"],"WorkPoints":["後面"," の底面を下にして を の内面側に取付ける","下から見た図"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["5mm"]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ全体組立②","WorkItems":["1. と をWASHER BOLT BOLT で取付"],"WorkPoints":["後面"," の底面を下にして を の内面側に取付ける","下から見た図"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["5mm"],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"1000㎜","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ全体組立③","WorkItems":["1. に をWASHER BOLT で取付"],"WorkPoints":["左面","左面側に各材料の端面合わせ"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["220mm","290mm","720mm"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"1000㎜","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ全体組立③","WorkItems":["1. に をWASHER BOLT で取付"],"WorkPoints":["左面","左面側に各材料の端面合わせ"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["220mm","290mm","720mm"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±0.5㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ全体組立③","WorkItems":["1. に をWASHER BOLT で取付"],"WorkPoints":["左面","左面側に各材料の端面合わせ"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["220mm","290mm","720mm"]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ全体組立③","WorkItems":["1. に をWASHER BOLT で取付"],"WorkPoints":["左面","左面側に各材料の端面合わせ"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["220mm","290mm","720mm"],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"1000㎜","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ全体組立④","WorkItems":["1. に をWASHER BOLT で取付","2. 1.完成品とWASHER SUPPORT NUT を後工程に払い出し"],"WorkPoints":["上面","上面側に端面合わせ"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["685mm","685mm"]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"1000㎜","ToolOther":"","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ全体組立④","WorkItems":["1. に をWASHER BOLT で取付","2. 1.完成品とWASHER SUPPORT NUT を後工程に払い出し"],"WorkPoints":["上面","上面側に端面合わせ"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["685mm","685mm"],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示寸法各±0.5㎜","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ全体組立④","WorkItems":["1. に をWASHER BOLT で取付","2. 1.完成品とWASHER SUPPORT NUT を後工程に払い出し"],"WorkPoints":["上面","上面側に端面合わせ"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["685mm","685mm"]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾚﾝﾁ","Size":"5㎜","ToolOther":"11.5N･m","WorkName":"共通(L)ﾌﾚｰﾑｷｯﾄ全体組立④","WorkItems":["1. に をWASHER BOLT で取付","2. 1.完成品とWASHER SUPPORT NUT を後工程に払い出し"],"WorkPoints":["上面","上面側に端面合わせ"],"Tolks":["締付ﾄﾙｸ11.5N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["685mm","685mm"],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"11.5N･m±10%","Method":"ﾄﾙｸﾚﾝﾁ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸｽﾊﾟﾅ","Size":"7㎜","ToolOther":"1.2N･m","WorkName":"ﾊﾞﾙﾌﾞ組立","WorkItems":["1. VALVE にJOINT SILENCER JOINT を取付ける","2. 1完成品にTUBE を取付ける"],"WorkPoints":["TUBE を120㎜にｶｯﾄする","ｻｲﾚﾝｻの根元を掴んで取付けの事"],"Tolks":["締付ﾄﾙｸ 1.2N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸｽﾊﾟﾅ","Size":"7㎜","ToolOther":"1.2N･m","WorkName":"ﾊﾞﾙﾌﾞ組立","WorkItems":["1. VALVE にJOINT SILENCER JOINT を取付ける","2. 1完成品にTUBE を取付ける"],"WorkPoints":["TUBE を120㎜にｶｯﾄする","ｻｲﾚﾝｻの根元を掴んで取付けの事"],"Tolks":["締付ﾄﾙｸ 1.2N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"1.2N･m±10%","Method":"ﾄﾙｸｽﾊﾟﾅ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"ﾊﾞﾙﾌﾞ組立","WorkItems":[],"WorkPoints":["ｻｲﾚﾝｻの根元を掴んで取付けの事"],"Tolks":["締付ﾄﾙｸ 1.2N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ｽｹｰﾙ","Size":"150㎜","ToolOther":"","WorkName":"ﾊﾞﾙﾌﾞ組立","WorkItems":[],"WorkPoints":["ｻｲﾚﾝｻの根元を掴んで取付けの事"],"Tolks":["締付ﾄﾙｸ 1.2N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"寸法確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"作業指示の寸法である事","Method":"ｽｹｰﾙ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"ﾊﾞﾙﾌﾞ組立","WorkItems":["1. VALVE にJOINT SILENCER JOINT を取付ける","2. 1完成品にTUBE を取付ける"],"WorkPoints":["TUBE を120㎜にｶｯﾄする","ｻｲﾚﾝｻの根元を掴んで取付けの事"],"Tolks":["締付ﾄﾙｸ 1.2N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"ﾊﾞﾙﾌﾞ組立","WorkItems":["1. VALVE にJOINT SILENCER JOINT を取付ける","2. 1完成品にTUBE を取付ける"],"WorkPoints":["TUBE を120㎜にｶｯﾄする","ｻｲﾚﾝｻの根元を掴んで取付けの事"],"Tolks":["締付ﾄﾙｸ 1.2N･m"],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"接続確認","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示通り接続出来ている事","Method":"目視","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾄﾞﾗｲﾊﾞｰ","Size":"2.5㎜","ToolOther":"95cN･m","WorkName":"ｼﾘﾝﾀﾞ組立1","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾄﾞﾗｲﾊﾞｰ","Size":"2.5㎜","ToolOther":"95cN･m","WorkName":"ｼﾘﾝﾀﾞ組立1","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"95cN･m±10%","Method":"ﾄﾙｸﾄﾞﾗｲﾊﾞｰ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾄﾞﾗｲﾊﾞｰ","Size":"","ToolOther":"","WorkName":"ｼﾘﾝﾀﾞ組立2","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾄﾞﾗｲﾊﾞｰ","Size":"","ToolOther":"","WorkName":"ｼﾘﾝﾀﾞ組立2","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"95cN･m±10%","Method":"ﾄﾙｸﾄﾞﾗｲﾊﾞｰ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"ｼﾘﾝﾀﾞ組立2","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"-","Size":"","ToolOther":"","WorkName":"ｼﾘﾝﾀﾞ組立2","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"塗布量","ToolManageNo":"-","ToolCycle":"-","ToolRecord":"-","StdVal":"指示箇所に塗布米粒:1米粒:2","Method":"目視","RecordMethod":"-","Other":"ｸﾞﾘｰｽLCG100","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｼﾘﾝﾀﾞｰﾌﾞﾛｯｸ保持治具","Size":"","ToolOther":"FM-3087","WorkName":"ｼﾘﾝﾀﾞ組立2","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WDSJ-G002-C11"]} | {"WorkTypes":[],"ToolName":"ｼﾘﾝﾀﾞｰﾌﾞﾛｯｸ保持治具","Size":"","ToolOther":"FM-3087","WorkName":"ｼﾘﾝﾀﾞ組立2","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WDSJ-G002-C11"],"QualityItem":"ｼﾘﾝﾀﾞｰ調整","ToolManageNo":"FM-3087","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"16±0.1㎜","Method":"目視","RecordMethod":"WDSJ-G002-C11","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸｽﾊﾟﾅ","Size":"","ToolOther":"","WorkName":"ｼﾘﾝﾀﾞ組立2","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸｽﾊﾟﾅ","Size":"","ToolOther":"","WorkName":"ｼﾘﾝﾀﾞ組立2","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"1.2N･m±10%","Method":"ﾄﾙｸｽﾊﾟﾅ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ｼｯｸﾈｽｹﾞｰｼﾞ","Size":"","ToolOther":"","WorkName":"ｼﾘﾝﾀﾞ組立2","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WDSJ-G002-C11"]} | {"WorkTypes":[],"ToolName":"ｼｯｸﾈｽｹﾞｰｼﾞ","Size":"","ToolOther":"","WorkName":"ｼﾘﾝﾀﾞ組立2","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":["WDSJ-G002-C11"],"QualityItem":"隙間確認","ToolManageNo":"-","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"0.1㎜が通らないこと","Method":"ｼｯｸﾈｽｹﾞｰｼﾞ","RecordMethod":"WDSJ-G002-C11","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"位置合わせ治具","Size":"","ToolOther":"FM-6131","WorkName":"ｼﾘﾝﾀﾞ組立3","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"位置合わせ治具","Size":"","ToolOther":"FM-6131","WorkName":"ｼﾘﾝﾀﾞ組立3","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"位置確認","ToolManageNo":"FM-6131","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"ﾄﾙｸﾄﾞﾗｲﾊﾞｰ","Size":"","ToolOther":"","WorkName":"ｼﾘﾝﾀﾞ組立3","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"ﾄﾙｸﾄﾞﾗｲﾊﾞｰ","Size":"","ToolOther":"","WorkName":"ｼﾘﾝﾀﾞ組立3","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"締付ﾄﾙｸ","ToolManageNo":"-","ToolCycle":"日常点検(1回/日)","ToolRecord":"ﾄﾙｸﾁｪｯｸ台帳","StdVal":"95cN･m±10%","Method":"ﾄﾙｸﾄﾞﾗｲﾊﾞｰ","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null | |
{"WorkTypes":[],"ToolName":"位置合わせ治具","Size":"","ToolOther":"FM-6131","WorkName":"ｼﾘﾝﾀﾞ組立4","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[]} | {"WorkTypes":[],"ToolName":"位置合わせ治具","Size":"","ToolOther":"FM-6131","WorkName":"ｼﾘﾝﾀﾞ組立4","WorkItems":[],"WorkPoints":[],"Tolks":[],"InspectionNo":"","InspectionItems":[],"_workType":[],"Words":[],"QualityItem":"位置確認","ToolManageNo":"FM-6131","ToolCycle":"校正対象外","ToolRecord":"-","StdVal":"指示通り作業出来ている事","Method":"目視","RecordMethod":"-","Other":"-","ProcessNames":[]} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.