Datasets:
ayuzawa
/
ManageProcess19

Dataset card Data Studio Files
xet
Community
1
input
stringclasses
1 value
instruction
stringlengths
222
1.92k
output
stringlengths
193
312
category
stringclasses
1 value
index
stringclasses
1 value
fileName
null
{ "ToolName": "-", "Size": "", "ToolOther": "ｸﾞﾘｰｽ", "WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-③", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "塗布確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り塗布出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾃﾞｼﾞﾀﾙはかり", "Size": "", "ToolOther": "", "WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-④", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "5g~7g", "Method": "ﾃﾞｼﾞﾀﾙはかり", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "【ｸﾞﾘｰｽ注入機作業】ﾘﾆｱﾌﾞｯｼｭのｸﾞﾘｰｽ塗布-④", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "小豆:2", "Method": "目視", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱｼｬﾌﾄ組立て、ｸﾞﾘｰｽ塗布", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布小豆:各1", "Method": "目視", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾄﾘﾑ接着", "WorkItems": [ "▲1. BRACKET にTRIM を接着する｡" ], "WorkPoints": [ "接着剤をｺﾞﾏ粒の量･ﾄﾘﾑ寸法長さに塗布し､ﾄﾘﾑを取付", "下当付け" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "28㎜", "1㎜", "16㎜", "ﾄﾘﾑ", "接着剤", "･ﾄﾘﾑ取付後､接着剤の はみ出しが無い事", "･ﾄﾘﾑ寸法､長さに塗付" ] }
{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "剥がれ無い事ｺﾞﾏ粒×16㎜ｺﾞﾏ粒×28㎜", "Method": "目視", "RecordMethod": "-", "Other": "ﾛｯｸﾀｲﾄ415", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "50cN･m", "WorkName": "ｿﾚﾉｲﾄﾞﾊﾞﾙﾌﾞ組立", "WorkItems": [], "WorkPoints": [ "ﾏｰｸの向きが図の様に取付け" ], "Tolks": [ "締付ﾄﾙｸ 50cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "70cN・m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "50cN･m", "WorkName": "ｿﾚﾉｲﾄﾞﾊﾞﾙﾌﾞ組立", "WorkItems": [], "WorkPoints": [ "ﾏｰｸの向きが図の様に取付け" ], "Tolks": [ "締付ﾄﾙｸ 50cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "30cN・m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "50cN･m", "WorkName": "ｿﾚﾉｲﾄﾞﾊﾞﾙﾌﾞ組立", "WorkItems": [], "WorkPoints": [ "ﾏｰｸの向きが図の様に取付け" ], "Tolks": [ "締付ﾄﾙｸ 50cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "30cN・m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｺﾝﾍﾞｯｸｽ", "Size": "", "ToolOther": "", "WorkName": "ｿﾚﾉｲﾄﾞﾊﾞﾙﾌﾞ組立", "WorkItems": [], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 50cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法の長さにｶｯﾄしている事", "Method": "-", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "50cN･m", "WorkName": "上限下限ｾﾝｻ組立", "WorkItems": [], "WorkPoints": [ "ｾﾝｻの位置を合わせて締付けること", "表示面が上", "PLATE の平らな面が下" ], "Tolks": [ "締付ﾄﾙｸ 50cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "50cN・m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "", "ToolOther": "", "WorkName": "中継ｼﾞｮｲﾝﾄ組立、銘板貼付け", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "50cN・m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "", "ToolOther": "", "WorkName": "中継ｼﾞｮｲﾝﾄ組立、銘板貼付け", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "支持ﾎﾞﾙﾄ組立", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "作業確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "加工面に打痕､傷等無き事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "", "ToolOther": "", "WorkName": "中継ｼﾞｮｲﾝﾄﾌﾟﾚｰﾄ取付け", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.5N・m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｲﾝｼｭﾛｯｸﾀｲ、ｲﾝｼｭﾛｯｸ取付け", "WorkItems": [ "3. ⑯にｲﾝｼｭﾛｯｸを差込む｡", "2. にﾏｳﾝﾄを取付ける｡", "1. ㉙を塗布する" ], "WorkPoints": [ "M4ﾀｯﾌﾟ穴が手前", "⑯の方向に注意", "ｲﾝｼｭﾛｯｸの向きに注意", "M4ﾀｯﾌﾟ穴が手前" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "方向確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "作業指示通りの方向である事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "", "ToolOther": "", "WorkName": "ﾒｲﾝｼﾘﾝﾀﾞｰの取付け", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "5.3N・m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾒｲﾝｼﾘﾝﾀﾞｰの取付け", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "方向確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "作業指示通りの方向である事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱﾌﾞｯｼｭ取付け", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "9.8N・m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱﾌﾞｯｼｭ取付け", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.5N･m", "WorkName": "ｿﾚﾉｲﾄﾞﾊﾞﾙﾌﾞの取付け", "WorkItems": [ "1. に をBOLT WASHER で取付ける｡" ], "WorkPoints": [ "矢印方向に押して取付けること", " の取付け方向に注意" ], "Tolks": [ "締付ﾄﾙｸ 3.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.5N・m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｿﾚﾉｲﾄﾞﾊﾞﾙﾌﾞの取付け", "WorkItems": [ "1. に をBOLT WASHER で取付ける｡" ], "WorkPoints": [ "矢印方向に押して取付けること", " の取付け方向に注意" ], "Tolks": [ "締付ﾄﾙｸ 3.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "方向確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "作業指示通りの方向である事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "上限下限ｾﾝｻ取付け", "WorkItems": [ "1. にWASHER をBOLT WASHER で仮付ける｡" ], "WorkPoints": [ "目視にて長穴中央で仮付ける", "内輪の面取りは大きい方を上にする" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "", "ToolOther": "", "WorkName": "ｺﾈｸﾀﾌﾞﾗｹｯﾄ取付け", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.5N・m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｺﾈｸﾀﾌﾞﾗｹｯﾄ取付け", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配管接続", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "作業指示通り接続出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "PHｾﾝｻ引き回し", "WorkItems": [ "1. にCABLE orCABLE を接続する", "2. のｾﾝｻｺﾈｸﾀを接続する", "3. 配線を引き回す", "4. 各ｺﾈｸﾀにLABEL を取付ける" ], "WorkPoints": [ "Lane1用､Lane2用で使用部材が異なります!", "ｽﾍﾟｰｻｰと共締めのこと", "ﾀｸﾞのNo.が見える様に取付け" ], "Tolks": [], "InspectionNo": "WERP-F013-005", "InspectionItems": [ "検査表 :ｺﾈｸﾀ接続確認" ], "WorkTypes": [], "Words": [ "Lane1(A002):B1244PLane2(A001):B1235PPHｾﾝｻ:上側ｾﾝｻ(上限)", "Lane1(A002):B1245PLane2(A001):B1236PPHｾﾝｻ:下側ｾﾝｻ(下限)", "上限ｾﾝｻ", "下限ｾﾝｻ", "上限ｾﾝｻ側", "下限ｾﾝｻ側", "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "WERP-F013-005" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "作業指示通り接続出来ている事", "Method": "目視", "RecordMethod": "WERP-F013-005", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾊﾞﾙﾌﾞ切替配線", "WorkItems": [ "1. にCABLE orCABLE を接続する｡", "2. 配線配管を括る｡" ], "WorkPoints": [ "Lane1用､Lane2用で使用部材が異なります!", "R4134とR4136は括らない", "ｼﾘﾝﾀﾞｰ上継手に接続するﾁｭｰﾌﾞは括らない", "ﾁｭｰﾌﾞが干渉していないこと" ], "Tolks": [], "InspectionNo": "WERP-F013-005", "InspectionItems": [ "検査表 :ｺﾈｸﾀ接続確認" ], "WorkTypes": [], "Words": [ "Lane1(A003):R4135Lane2(A004):R4137", "Lane1(A003):R4134Lane2(A004):R4136", "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "WERP-F013-005" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "作業指示通り接続出来ている事", "Method": "目視", "RecordMethod": "WERP-F013-005", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "基板ﾎﾙﾀﾞ組立治具", "Size": "", "ToolOther": "FM-2672", "WorkName": "上ﾌﾟﾚｰﾄの取付けと位置調整", "WorkItems": [ "1. を組立治具のﾋﾟﾝに当てつけ取付ける" ], "WorkPoints": [ "治具台取付後､防錆油を塗布すること", "※PLATE は左奥と右前の対角に取付ける", "PLATE の向きに注意", "PLATE とHｶｯﾄの取付方向" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-2672", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "基板ﾎﾙﾀﾞﾌﾟﾚｰﾄ位置決め治具", "Size": "", "ToolOther": "FM-2673", "WorkName": "上ﾌﾟﾚｰﾄの取付けと位置調整", "WorkItems": [ "1. を組立治具のﾋﾟﾝに当てつけ取付ける", "2. に を挿入し､ のｼｬﾌﾄにPLATE をBOLT で取付ける", "3. の位置を調整し､締付ける｡" ], "WorkPoints": [ "治具台取付後､防錆油を塗布すること", "PLATE は左奥と右前の対角に取付ける", "※PLATE は左奥と右前の対角に取付ける", "PLATE の向きに注意", "ﾄﾞｸﾞ取付けﾀｯﾌﾟの位置に注意", " と治具の隙間:0.05㎜以内", " と治具の隙間:0.01㎜以内", "ｼｬﾌﾄのDｶｯﾄを点線に合わせて締付けること", "PLATE とHｶｯﾄの取付方向" ], "Tolks": [ "締付ﾄﾙｸ 9.8N･m" ], "InspectionNo": "WERP-F013-005", "InspectionItems": [ "検査表 :PLATE取付け位置確認" ], "WorkTypes": [], "Words": [ "治具台", "Dｶｯﾄ面(点線)", "FM2673組立治具", "FM2673組立治具", "FM2673組立治具", "WERP-F013-005" ] }
{ "QualityItem": "位置確認", "ToolManageNo": "FM-2673", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "隙間:0.01㎜以下", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "WERP-F013-005", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｼｬﾌﾄHｶｯﾄ方向合わせ治具", "Size": "", "ToolOther": "FM-4956", "WorkName": "上ﾌﾟﾚｰﾄの取付けと位置調整", "WorkItems": [ "1. を組立治具のﾋﾟﾝに当てつけ取付ける" ], "WorkPoints": [ "治具台取付後､防錆油を塗布すること", "※PLATE は左奥と右前の対角に取付ける", "PLATE の向きに注意", "PLATE とHｶｯﾄの取付方向" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-4956", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "9.8N･m", "WorkName": "上ﾌﾟﾚｰﾄの取付けと位置調整", "WorkItems": [ "2. に を挿入し､ のｼｬﾌﾄにPLATE をBOLT で取付ける", "3. の位置を調整し､締付ける｡" ], "WorkPoints": [ "PLATE は左奥と右前の対角に取付ける", "ﾄﾞｸﾞ取付けﾀｯﾌﾟの位置に注意" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :PLATE取付け位置確認" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "9.8N・m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｼﾘﾝﾀﾞｰ位置調整ｼﾞｸﾞ", "Size": "", "ToolOther": "FM-2982", "WorkName": "上ﾌﾟﾚｰﾄに対するﾒｲﾝｼﾘﾝﾀﾞの位置出し調整", "WorkItems": [ "1. のｼﾘﾝﾀﾞ部に治具をいれ､締付ける｡" ], "WorkPoints": [ "治具:FM-2982", "位置調整し締付ける", "治具がｽﾑｰｽﾞに上下すること" ], "Tolks": [ "締付ﾄﾙｸ 9.8N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "位置確認", "ToolManageNo": "FM-2982", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示通り位置確認する事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "9.8N･m", "WorkName": "上ﾌﾟﾚｰﾄに対するﾒｲﾝｼﾘﾝﾀﾞの位置出し調整", "WorkItems": [ "1. のｼﾘﾝﾀﾞ部に治具をいれ､締付ける｡" ], "WorkPoints": [ "治具:FM-2982", "位置調整し締付ける", "治具がｽﾑｰｽﾞに上下すること" ], "Tolks": [ "締付ﾄﾙｸ 9.8N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "9.8N・m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾉｷﾞｽ", "Size": "150㎜", "ToolOther": "", "WorkName": "上ﾌﾟﾚｰﾄの高さ調整とﾒｲﾝｼﾘﾝﾀﾞの連結", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "8.5㎜±0.05㎜", "◆作業者安全作業" ] }
{ "QualityItem": "出代確認", "ToolManageNo": "-", "ToolCycle": "1回/年", "ToolRecord": "校正成績表", "StdVal": "出代:8.5㎜±0.05", "Method": "ﾉｷﾞｽ", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "上ﾌﾟﾚｰﾄの高さ調整とﾒｲﾝｼﾘﾝﾀﾞの連結", "WorkItems": [ "◆1. CYL-NUT に㉙をかけグリスを塗布する", "◆2. WASHER にｸﾞﾘｰｽを塗布する(両面塗布)", "3. ｴｱｰを入れ に2.を取付ける", "4. CYL-NUT の締付け位置を調整する", "5. 位置調整後､ﾅｯﾄを締結する" ], "WorkPoints": [ "ｸﾞﾘｰｽを均等に塗布する", "WASHER 表裏にｸﾞﾘｰｽを均等に塗布する", "ﾉｷﾞｽでﾅｯﾄ上面からﾛｯﾄﾞ先端までの深さを測定する", "CYL-NUT の取付面に砥石掛け" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "8.5㎜±0.05㎜", "※ｴｱｰ投入､禁止のこと", "両面", "ｸﾞﾘｰｽ塗布 米粒:2", "ｸﾞﾘｰｽ塗布 米粒:2" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:2", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "基板ﾎﾙﾀﾞｰﾕﾆｯﾄﾁｪｯｶｰ", "Size": "", "ToolOther": "FM-2223", "WorkName": "ﾄﾞｸﾞ取付け", "WorkItems": [ "1. にDOG をBOLT WASHER で取付ける｡", "2. に治具を接続し､DOG の位置確認をする｡", "3. 位置調整後､締結する" ], "WorkPoints": [ "目視にて2/3ｾﾝｻｰに入れる", "目視にてｾﾝｻｰの中央" ], "Tolks": [ "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "位置確認", "ToolManageNo": "FM-2223", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.5N･m", "WorkName": "ﾄﾞｸﾞ取付け", "WorkItems": [ "1. にDOG をBOLT WASHER で取付ける｡" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.5N・m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "基板ﾎﾙﾀﾞｰﾕﾆｯﾄﾁｪｯｶｰ", "Size": "", "ToolOther": "FM-2223", "WorkName": "ｶﾞｲﾄﾞﾌﾟﾚｰﾄの取付け", "WorkItems": [ "1. にPLATE PLATE をBOLT で仮付ける｡", "2. PLATE PLATE の位置を調整し締付ける｡" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-2223", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "基板ﾎﾙﾀﾞｰ側面ﾌﾟﾚｰﾄ位置決め治具", "Size": "", "ToolOther": "FM-2675", "WorkName": "ｶﾞｲﾄﾞﾌﾟﾚｰﾄの取付け", "WorkItems": [ "1. にPLATE PLATE をBOLT で仮付ける｡", "2. PLATE PLATE の位置を調整し締付ける｡" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-2675", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾉｷﾞｽ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｶﾞｲﾄﾞﾌﾟﾚｰﾄの取付け", "WorkItems": [ "1. にPLATE PLATE をBOLT で仮付ける｡", "2. PLATE PLATE の位置を調整し締付ける｡" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "WERP-F013-005", "InspectionItems": [ "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認" ], "WorkTypes": [], "Words": [ "WERP-F013-005" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "1回/年", "ToolRecord": "校正成績表", "StdVal": "AB寸法:50㎜±0.1㎜", "Method": "ﾉｷﾞｽ", "RecordMethod": "WERP-F013-005", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "0.01㎜", "ToolOther": "", "WorkName": "ｶﾞｲﾄﾞﾌﾟﾚｰﾄの平面調整", "WorkItems": [ "1. のｸﾗﾝﾌﾟﾌﾟﾚｰﾄの基準高さを調整する｡", "2. ｸﾗﾝﾌﾟﾌﾟﾚｰﾄの平面調整をする｡", "1. のｸﾗﾝﾌﾟﾌﾟﾚｰﾄの基準高さを調整する｡", "2. ｸﾗﾝﾌﾟﾌﾟﾚｰﾄの平面調整をする｡", "1. のｸﾗﾝﾌﾟﾌﾟﾚｰﾄの基準高さを調整する｡", "2. ｸﾗﾝﾌﾟﾌﾟﾚｰﾄの平面調整をする｡" ], "WorkPoints": [ "C=117.5±0.05㎜", "調整後､再度上下させて確認すること", " ~⑥=±0.05㎜(狙い目は+方向)", "C=117.5±0.05㎜", "調整後､再度上下させて確認すること", " ~⑥=±0.05㎜(狙い目は+方向)", "C=117.5±0.05㎜", "調整後､再度上下させて確認すること", " ~⑥=±0.05㎜(狙い目は+方向)" ], "Tolks": [ "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m" ], "InspectionNo": "WERP-F013-005", "InspectionItems": [ "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認" ], "WorkTypes": [], "Words": [ "FM-2673", " を下降させた状態で調整すること", "検査表 :PLATEの調整", "FM-2673", " を下降させた状態で調整すること", "検査表 :PLATEの調整", "FM-2673", " を下降させた状態で調整すること", "検査表 :PLATEの調整", "WERP-F013-005" ] }
{ "QualityItem": "高さ確認", "ToolManageNo": "-", "ToolCycle": "2回/年", "ToolRecord": "校正成績表", "StdVal": "高さ:117.5±0.05㎜", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WERP-F013-005", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "0.01㎜", "ToolOther": "", "WorkName": "ｶﾞｲﾄﾞﾌﾟﾚｰﾄの平面調整", "WorkItems": [ "1. のｸﾗﾝﾌﾟﾌﾟﾚｰﾄの基準高さを調整する｡", "2. ｸﾗﾝﾌﾟﾌﾟﾚｰﾄの平面調整をする｡", "1. のｸﾗﾝﾌﾟﾌﾟﾚｰﾄの基準高さを調整する｡", "2. ｸﾗﾝﾌﾟﾌﾟﾚｰﾄの平面調整をする｡", "1. のｸﾗﾝﾌﾟﾌﾟﾚｰﾄの基準高さを調整する｡", "2. ｸﾗﾝﾌﾟﾌﾟﾚｰﾄの平面調整をする｡" ], "WorkPoints": [ "C=117.5±0.05㎜", "調整後､再度上下させて確認すること", " ~⑥=±0.05㎜(狙い目は+方向)", "C=117.5±0.05㎜", "調整後､再度上下させて確認すること", " ~⑥=±0.05㎜(狙い目は+方向)", "C=117.5±0.05㎜", "調整後､再度上下させて確認すること", " ~⑥=±0.05㎜(狙い目は+方向)" ], "Tolks": [ "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m" ], "InspectionNo": "WERP-F013-005", "InspectionItems": [ "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認" ], "WorkTypes": [], "Words": [ "FM-2673", " を下降させた状態で調整すること", "検査表 :PLATEの調整", "FM-2673", " を下降させた状態で調整すること", "検査表 :PLATEの調整", "FM-2673", " を下降させた状態で調整すること", "検査表 :PLATEの調整", "WERP-F013-005" ] }
{ "QualityItem": "平面確認", "ToolManageNo": "-", "ToolCycle": "2回/年", "ToolRecord": "校正成績表", "StdVal": "平面度:±0.05㎜以内", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WERP-F013-005", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "基板ﾎﾙﾀﾞｰﾕﾆｯﾄﾁｪｯｶｰ", "Size": "", "ToolOther": "FM-2223", "WorkName": "ｶﾞｲﾄﾞﾌﾟﾚｰﾄの平面調整", "WorkItems": [ "1. のｸﾗﾝﾌﾟﾌﾟﾚｰﾄの基準高さを調整する｡", "2. ｸﾗﾝﾌﾟﾌﾟﾚｰﾄの平面調整をする｡", "3. ｸﾗﾝﾌﾟﾌﾟﾚｰﾄの基準高さを確認する｡" ], "WorkPoints": [ "治具:FM-3147を取付ける", "C=117.5±0.05㎜", "調整後､再度上下させて確認すること", " ~⑥=±0.05㎜(狙い目は+方向)", "上昇させて を基準に②~⑥の平面を調整し､再度動作させ確認する｡", "高さが規格外の場合､再度調整し直すこと(1の作業から)" ], "Tolks": [ "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "FM-2673", " を下降させた状態で調整すること", "60mm", "60mm", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :PLATEの調整", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-2223", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "基板ﾎﾙﾀﾞｰﾌﾟﾚｰﾄ位置決め治具", "Size": "", "ToolOther": "FM-2673", "WorkName": "ｶﾞｲﾄﾞﾌﾟﾚｰﾄの平面調整", "WorkItems": [ "1. のｸﾗﾝﾌﾟﾌﾟﾚｰﾄの基準高さを調整する｡", "2. ｸﾗﾝﾌﾟﾌﾟﾚｰﾄの平面調整をする｡", "1. のｸﾗﾝﾌﾟﾌﾟﾚｰﾄの基準高さを調整する｡", "2. ｸﾗﾝﾌﾟﾌﾟﾚｰﾄの平面調整をする｡", "1. のｸﾗﾝﾌﾟﾌﾟﾚｰﾄの基準高さを調整する｡", "2. ｸﾗﾝﾌﾟﾌﾟﾚｰﾄの平面調整をする｡" ], "WorkPoints": [ "C=117.5±0.05㎜", "調整後､再度上下させて確認すること", " ~⑥=±0.05㎜(狙い目は+方向)", "C=117.5±0.05㎜", "調整後､再度上下させて確認すること", " ~⑥=±0.05㎜(狙い目は+方向)", "C=117.5±0.05㎜", "調整後､再度上下させて確認すること", " ~⑥=±0.05㎜(狙い目は+方向)" ], "Tolks": [ "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "FM-2673", " を下降させた状態で調整すること", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :PLATEの調整", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "FM-2673", " を下降させた状態で調整すること", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :PLATEの調整", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "FM-2673", " を下降させた状態で調整すること", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :PLATEの調整", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-2673", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "基板ﾎﾙﾀﾞ上昇ｽﾄｯﾊﾟｰ", "Size": "", "ToolOther": "FM-3147", "WorkName": "ｶﾞｲﾄﾞﾌﾟﾚｰﾄの平面調整", "WorkItems": [ "1. のｸﾗﾝﾌﾟﾌﾟﾚｰﾄの基準高さを調整する｡", "2. ｸﾗﾝﾌﾟﾌﾟﾚｰﾄの平面調整をする｡", "3. ｸﾗﾝﾌﾟﾌﾟﾚｰﾄの基準高さを確認する｡" ], "WorkPoints": [ "治具:FM-3147を取付ける", "C=117.5±0.05㎜", "調整後､再度上下させて確認すること", " ~⑥=±0.05㎜(狙い目は+方向)", "上昇させて を基準に②~⑥の平面を調整し､再度動作させ確認する｡", "高さが規格外の場合､再度調整し直すこと(1の作業から)" ], "Tolks": [ "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "FM-2673", " を下降させた状態で調整すること", "60mm", "60mm", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :PLATEの調整", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-3147", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.5N･m", "WorkName": "ｶﾞｲﾄﾞﾌﾟﾚｰﾄの平面調整", "WorkItems": [ "1. のｸﾗﾝﾌﾟﾌﾟﾚｰﾄの基準高さを調整する｡", "2. ｸﾗﾝﾌﾟﾌﾟﾚｰﾄの平面調整をする｡", "1. のｸﾗﾝﾌﾟﾌﾟﾚｰﾄの基準高さを調整する｡", "2. ｸﾗﾝﾌﾟﾌﾟﾚｰﾄの平面調整をする｡", "1. のｸﾗﾝﾌﾟﾌﾟﾚｰﾄの基準高さを調整する｡", "2. ｸﾗﾝﾌﾟﾌﾟﾚｰﾄの平面調整をする｡" ], "WorkPoints": [ "C=117.5±0.05㎜", "調整後､再度上下させて確認すること", " ~⑥=±0.05㎜(狙い目は+方向)", "C=117.5±0.05㎜", "調整後､再度上下させて確認すること", " ~⑥=±0.05㎜(狙い目は+方向)", "C=117.5±0.05㎜", "調整後､再度上下させて確認すること", " ~⑥=±0.05㎜(狙い目は+方向)" ], "Tolks": [ "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m", "締付ﾄﾙｸ 3.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "FM-2673", " を下降させた状態で調整すること", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :PLATEの調整", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "FM-2673", " を下降させた状態で調整すること", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :PLATEの調整", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "FM-2673", " を下降させた状態で調整すること", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認", "検査表 :PLATEの調整", "検査表 :ｸﾗﾝﾌﾟPLATE取付け高さ確認" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.5N・m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼ", "Size": "", "ToolOther": "", "WorkName": "支持ﾎﾞﾙﾄ取付け高さ確認", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "WERP-F013-005" ] }
{ "QualityItem": "高さ確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績表", "StdVal": "検査表通りの高さ調整する事", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WERP-F013-005", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "下受けﾌﾟﾚｰﾄ搭載面調整治具", "Size": "", "ToolOther": "FM-3684", "WorkName": "支持ﾎﾞﾙﾄ取付け高さ確認", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-3684", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "基板ﾎﾙﾀﾞ上昇ｽﾄｯﾊﾟｰ", "Size": "", "ToolOther": "FM-3147", "WorkName": "支持ﾎﾞﾙﾄ取付け高さ確認", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-3147", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "", "ToolOther": "", "WorkName": "支持ﾎﾞﾙﾄ取付け高さ確認", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.5N・m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "", "ToolOther": "", "WorkName": "ﾊﾟﾝﾁﾝｸﾞﾌﾟﾚｰﾄ取付け", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "250cN・m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾊﾟﾝﾁﾝｸﾞﾌﾟﾚｰﾄ取付け", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "位置確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾒｲﾊﾞﾝ貼付け", "WorkItems": [ "1. COVER にLABEL 貼付ける(ﾌﾛﾝﾄ側)", "2. COVER にLABEL 貼付ける(ﾘｱ側)", "1. COVER にLABEL 貼付ける(ﾌﾛﾝﾄ側)", "2. COVER にLABEL 貼付ける(ﾘｱ側)" ], "WorkPoints": [ "端面からの距離が長い", "端面からの距離が短い", "端面からの距離が長い", "端面からの距離が短い" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "33.5mm", "115mm", "33.5mm", "115mm" ] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌﾟﾚｰﾄの取付け(ｼｮｰﾄ250㎜仕様)", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾒｲﾊﾞﾝ貼付治具", "Size": "", "ToolOther": "", "WorkName": "ｼﾘｱﾙｼｰﾙ貼付け", "WorkItems": [ "1. に②を貼付ける" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "30㎜", "2㎜" ] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "作業指示通り貼付出来ている事", "Method": "ﾒｲﾊﾞﾝ貼付治具", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "基板ﾎﾙﾀﾞｰﾕﾆｯﾄﾁｪｯｶｰ", "Size": "", "ToolOther": "FM-2223", "WorkName": "基板下受け上下ｽﾋﾟｰﾄﾞ調整", "WorkItems": [ "1. のｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗを調整する", "2. 調整用ﾛｯｸﾅｯﾄを指締め後ﾛｯｸﾅｯﾄとｽﾋﾟｺﾝﾛｯｸﾅｯﾄにﾏｰｶで.Iﾏｰｸ入れる｡", "3. ｽﾋﾟｺﾝﾛｯｸﾅｯﾄにｽﾊﾟﾅをｾｯﾄし回らないようにし.調整用ﾛｯｸﾅｯﾄをﾗｼﾞｵﾍﾟﾝﾁでﾛｰﾚｯﾄ溝を1~2溝で締付ける｡", "4. のｾﾝｻのI/Oﾁｪｯｸをする" ], "WorkPoints": [ "元ｴｱｰ圧:0.52Mpa ~ 0.53Mpaに設定", "下降:0.9s±0.02s", "上昇:1.1s±0.02s" ], "Tolks": [], "InspectionNo": "WERP-F013-005", "InspectionItems": [ "検査表 :基板下受け上下ｽﾋﾟｰﾄﾞ調整" ], "WorkTypes": [], "Words": [ "上昇", "下降", " を上下させｾﾝｻを遮光しているか確認する", "ﾛｯｸ後", "ﾛｯｸ前", "ｽﾊﾟﾅ", "ｽﾋﾟｺﾝﾛｯｸﾅｯﾄ", "調整用ﾛｯｸﾅｯﾄ", "ｽﾋﾟｺﾝﾛｯｸﾅｯﾄ", "調整用ﾛｯｸﾅｯﾄ", "検査表 :I/Oﾁｪｯｸ", "調整用ﾛｯｸﾅｯﾄ", "WERP-F013-005" ] }
{ "QualityItem": "速度確認", "ToolManageNo": "FM-2223", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "上昇値:1.1s±0.02s", "Method": "基板ﾎﾙﾀﾞｰﾕﾆｯﾄﾁｪｯｶｰ", "RecordMethod": "WERP-F013-005", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "基板ﾎﾙﾀﾞｰﾕﾆｯﾄﾁｪｯｶｰ", "Size": "", "ToolOther": "FM-2223", "WorkName": "基板下受け上下ｽﾋﾟｰﾄﾞ調整", "WorkItems": [ "1. のｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗを調整する", "2. 調整用ﾛｯｸﾅｯﾄを指締め後ﾛｯｸﾅｯﾄとｽﾋﾟｺﾝﾛｯｸﾅｯﾄにﾏｰｶで.Iﾏｰｸ入れる｡", "3. ｽﾋﾟｺﾝﾛｯｸﾅｯﾄにｽﾊﾟﾅをｾｯﾄし回らないようにし.調整用ﾛｯｸﾅｯﾄをﾗｼﾞｵﾍﾟﾝﾁでﾛｰﾚｯﾄ溝を1~2溝で締付ける｡", "4. のｾﾝｻのI/Oﾁｪｯｸをする" ], "WorkPoints": [ "元ｴｱｰ圧:0.52Mpa ~ 0.53Mpaに設定", "下降:0.9s±0.02s", "上昇:1.1s±0.02s" ], "Tolks": [], "InspectionNo": "WERP-F013-005", "InspectionItems": [ "検査表 :基板下受け上下ｽﾋﾟｰﾄﾞ調整" ], "WorkTypes": [], "Words": [ "上昇", "下降", " を上下させｾﾝｻを遮光しているか確認する", "ﾛｯｸ後", "ﾛｯｸ前", "ｽﾊﾟﾅ", "ｽﾋﾟｺﾝﾛｯｸﾅｯﾄ", "調整用ﾛｯｸﾅｯﾄ", "ｽﾋﾟｺﾝﾛｯｸﾅｯﾄ", "調整用ﾛｯｸﾅｯﾄ", "検査表 :I/Oﾁｪｯｸ", "調整用ﾛｯｸﾅｯﾄ", "WERP-F013-005" ] }
{ "QualityItem": "速度確認", "ToolManageNo": "FM-2223", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "下降値:0.9s±0.02s", "Method": "基板ﾎﾙﾀﾞｰﾕﾆｯﾄﾁｪｯｶｰ", "RecordMethod": "WERP-F013-005", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "基板ﾎﾙﾀﾞｰﾕﾆｯﾄﾁｪｯｶｰ", "Size": "", "ToolOther": "FM-2223", "WorkName": "基板下受け上下ｽﾋﾟｰﾄﾞ調整", "WorkItems": [ "1. のｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗを調整する", "2. 調整用ﾛｯｸﾅｯﾄを指締め後ﾛｯｸﾅｯﾄとｽﾋﾟｺﾝﾛｯｸﾅｯﾄにﾏｰｶで.Iﾏｰｸ入れる｡", "3. ｽﾋﾟｺﾝﾛｯｸﾅｯﾄにｽﾊﾟﾅをｾｯﾄし回らないようにし.調整用ﾛｯｸﾅｯﾄをﾗｼﾞｵﾍﾟﾝﾁでﾛｰﾚｯﾄ溝を1~2溝で締付ける｡", "4. のｾﾝｻのI/Oﾁｪｯｸをする" ], "WorkPoints": [ "元ｴｱｰ圧:0.52Mpa ~ 0.53Mpaに設定", "下降:0.9s±0.02s", "上昇:1.1s±0.02s" ], "Tolks": [], "InspectionNo": "WERP-F013-005", "InspectionItems": [ "検査表 :基板下受け上下ｽﾋﾟｰﾄﾞ調整" ], "WorkTypes": [], "Words": [ "上昇", "下降", " を上下させｾﾝｻを遮光しているか確認する", "ﾛｯｸ後", "ﾛｯｸ前", "ｽﾊﾟﾅ", "ｽﾋﾟｺﾝﾛｯｸﾅｯﾄ", "調整用ﾛｯｸﾅｯﾄ", "ｽﾋﾟｺﾝﾛｯｸﾅｯﾄ", "調整用ﾛｯｸﾅｯﾄ", "検査表 :I/Oﾁｪｯｸ", "調整用ﾛｯｸﾅｯﾄ", "WERP-F013-005" ] }
{ "QualityItem": "I/O確認", "ToolManageNo": "FM-2223", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ｾﾝｻ遮光時LEDが消灯の事", "Method": "基板ﾎﾙﾀﾞｰﾕﾆｯﾄﾁｪｯｶｰ", "RecordMethod": "WERP-F013-005", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "基板ﾎﾙﾀﾞｰﾕﾆｯﾄﾁｪｯｶｰ", "Size": "", "ToolOther": "FM-2223", "WorkName": "ｴｰｼﾞﾝｸﾞ", "WorkItems": [ "1. のｴｰｼﾞﾝｸﾞをする", "2. のｽﾋﾟｰﾄﾞを確認し規格外の場合再調整する", "3. のｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗを以下4.5の手順でﾛｯｸする", "4. 調整用ﾛｯｸﾅｯﾄを指締め後ﾛｯｸﾅｯﾄと ｽﾋﾟｺﾝﾛｯｸﾅｯﾄにﾏｰｶで.Iﾏｰｸ入れる｡", "5. ｽﾋﾟｺﾝﾛｯｸﾅｯﾄにｽﾊﾟﾅをｾｯﾄし回らないようにし.調整用ﾛｯｸﾅｯﾄをﾗｼﾞｵﾍﾟﾝﾁでﾛｰﾚｯﾄ溝を1~2溝で締付ける｡" ], "WorkPoints": [ "ｴｱｰ圧:0.52Mpa ~ 0.53Mpa", "下降:0.9s±0.02s", "上昇:1.1s±0.02s", "再調整の際ｽﾋﾟｺﾝﾛｯｸﾅｯﾄにｽﾊﾟﾅをｾｯﾄし ｽﾋﾟｺﾝ本体が緩まない様に調整用ﾛｯｸﾅｯﾄを ﾗｼﾞｵﾍﾟﾝﾁで緩めること｡", "ﾛｯｸﾅｯﾄの締め過ぎによる破損に注意", "調整用ﾛｯｸﾅｯﾄを指で回し緩まないことを確認する｡", "Iﾏｰｸは最終消す｡" ], "Tolks": [], "InspectionNo": "WERP-F013-005", "InspectionItems": [ "検査表 :基板下受け上下ｽﾋﾟｰﾄﾞ調整" ], "WorkTypes": [], "Words": [ "上昇", "下降", "ﾛｯｸ後", "ｽﾋﾟｺﾝﾛｯｸﾅｯﾄ", "ﾛｯｸ前", "調整用ﾛｯｸﾅｯﾄ", "調整用ﾛｯｸﾅｯﾄ", "ｽﾊﾟﾅ", "ｽﾊﾟﾅ", "ｽﾋﾟｺﾝﾛｯｸﾅｯﾄ", "ｽﾋﾟｺﾝﾛｯｸﾅｯﾄ", "調整用ﾛｯｸﾅｯﾄ", "WERP-F013-005" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-2223", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ｴﾗｰ無きこと", "Method": "目視", "RecordMethod": "WERP-F013-005", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "600㎜", "ToolOther": "", "WorkName": "ｵｲﾙﾊﾟﾝ組立", "WorkItems": [ "▲2. 1完成品に㉘を塗布し、TRIM を貼付ける", "1. COVER にLABEL を貼付ける" ], "WorkPoints": [ "貼付け面は脱脂する事", "貼付け面は脱脂する事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この部分を持ってﾋﾞｰﾑを移動し無い事 /Do not move an X beam with this part / □□□□□□□□□□□□□□", "396㎜", "接着剤塗布 1ﾄﾘﾑにつきｺﾞﾏ粒:6", "この作業では同じものを2個製作", "▲特殊作業" ] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｵｲﾙﾊﾟﾝ組立", "WorkItems": [ "▲2. 1完成品に㉘を塗布し、TRIM を貼付ける", "1. COVER にLABEL を貼付ける" ], "WorkPoints": [ "側面", "写真の右側も同様に塗布する", "貼付け面は脱脂する事", "貼付け面は脱脂する事", "表面", "裏面" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この部分を持ってﾋﾞｰﾑを移動し無い事 /Do not move an X beam with this part / □□□□□□□□□□□□□□", "396㎜", "1㎜", "接着剤塗布 1ﾄﾘﾑにつきｺﾞﾏ粒:6", "COVER ", "TRIM ", "LABEL ", "この作業では同じものを2個製作", "TRIM ", "COVER ", "LABEL " ] }
{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ｺﾞﾏ粒:6", "Method": "目視", "RecordMethod": "-", "Other": "ﾛｯｸﾀｲﾄ415", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｱﾙｶﾝｻｽ", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立①", "WorkItems": [ "1. PLATE の両面に砥石をかける", "2. 1完成品にPIN を圧入する(4箇所)" ], "WorkPoints": [ "ﾋﾟﾝ圧入面(ｻﾞｸﾞﾘ穴側)と圧入方向に注意する", "ﾋﾟﾝ出代:2.5㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "裏 面", "表 面", "2.5㎜", "表 面", "この作業では同じものを2個製作" ] }
{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "傷、ﾊﾞﾘ等無き事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "圧入台", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立①", "WorkItems": [ "1. PLATE の両面に砥石をかける", "2. 1完成品にPIN を圧入する(4箇所)" ], "WorkPoints": [ "ﾋﾟﾝ圧入面(ｻﾞｸﾞﾘ穴側)と圧入方向に注意する", "ﾋﾟﾝ出代:2.5㎜", "PINの面取り部分を下に向けて圧入する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "裏 面", "表 面", "2.5㎜", "表 面", "2.5㎜", "表 面", "この作業では同じものを2個製作" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "Pin圧入治具", "Size": "", "ToolOther": "FM-5868", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立①", "WorkItems": [ "1. PLATE の両面に砥石をかける", "2. 1完成品にPIN を圧入する(4箇所)" ], "WorkPoints": [ "ﾋﾟﾝ圧入面(ｻﾞｸﾞﾘ穴側)と圧入方向に注意する", "ﾋﾟﾝ出代:2.5㎜", "PINの面取り部分を下に向けて圧入する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "裏 面", "表 面", "2.5㎜", "表 面", "2.5㎜", "表 面", "この作業では同じものを2個製作" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-5868", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立①", "WorkItems": [ "1. PLATE の両面に砥石をかける", "2. 1完成品にPIN を圧入する(4箇所)" ], "WorkPoints": [ "ﾋﾟﾝ圧入面(ｻﾞｸﾞﾘ穴側)と圧入方向に注意する", "ﾋﾟﾝ出代:2.5㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "裏 面", "表 面", "2.5㎜", "表 面", "この作業では同じものを2個製作" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｱﾙｶﾝｻｽ", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立②", "WorkItems": [ "1. X-PLATE の両面に砥石をかける", "2. X-PLATE にPIN を圧入する" ], "WorkPoints": [ "表裏でﾋﾟﾝ出代が違うので注意する事", "この作業では同じものを2個製作", "PIN ﾋﾟﾝ出代:7㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "7mm", "裏 面", "7mm" ] }
{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "傷、ﾊﾞﾘ等無き事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "圧入台", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立②", "WorkItems": [ "1. X-PLATE の両面に砥石をかける", "2. X-PLATE にPIN を圧入する" ], "WorkPoints": [ "表裏でﾋﾟﾝ出代が違うので注意する事", "この作業では同じものを2個製作", "PIN ﾋﾟﾝ出代:7㎜", "PIN ﾋﾟﾝ出代:5㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "7mm", "表 面", "裏 面", "7mm", "5mm" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "Pin圧入治具", "Size": "", "ToolOther": "FM-5831", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立②", "WorkItems": [ "1. X-PLATE の両面に砥石をかける", "2. X-PLATE にPIN を圧入する" ], "WorkPoints": [ "表裏でﾋﾟﾝ出代が違うので注意する事", "この作業では同じものを2個製作", "PIN ﾋﾟﾝ出代:7㎜", "PIN ﾋﾟﾝ出代:5㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "7mm", "表 面", "裏 面", "7mm", "5mm" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-5831", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立②", "WorkItems": [ "1. X-PLATE の両面に砥石をかける", "2. X-PLATE にPIN を圧入する" ], "WorkPoints": [ "表裏でﾋﾟﾝ出代が違うので注意する事", "この作業では同じものを2個製作", "PIN ﾋﾟﾝ出代:7㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "7mm", "裏 面", "7mm" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "110cN･m", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立③", "WorkItems": [ "1. にCLIP BOLT を取付ける" ], "WorkPoints": [ "表 :4箇所", "B視点", "A視点", "この作業では同じものを2個製作", "CLIP の取付方向や位置を間違えないように取付ける事(下図参照)", "このﾏｳﾝﾄは矢印方向に当てつけて取付ける", "このﾏｳﾝﾄは矢印方向に当てつけて取付ける", "穴の側面とﾏｳﾝﾄの側面を合わせて取付を行う", "当てつけて取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 110cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "A視点", "B視点" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "110cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立④", "WorkItems": [ "1. にSTOPPER SPACER をBOLT で取付ける" ], "WorkPoints": [ "この作業では同じものを2個製作" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "40cN･m", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立④", "WorkItems": [ "2. FAN にLABEL を取付ける", "4. 1完成品に2完成品をBOLT WASHER で取付ける" ], "WorkPoints": [ "ﾌｧﾝの銘板が下になるようにして取付ける事", "FANの型式ﾗﾍﾞﾙが見え無い事", "FANｹｰﾌﾞﾙの向きに注意すること(ｺﾈｸﾀｰの向きに注意する事)", "ﾁｭｰﾌﾞの先端に合わせる" ], "Tolks": [ "締付ﾄﾙｸ 40cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "40cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立④", "WorkItems": [ "■3. FAN の型式を確認し､ｼﾘｱﾙ番号を転記", "1. にSTOPPER SPACER をBOLT で取付ける", "2. FAN にLABEL を取付ける", "4. 1完成品に2完成品をBOLT WASHER で取付ける" ], "WorkPoints": [ "この作業では同じものを2個製作", "ﾌｧﾝの銘板が下になるようにして取付ける事", "FANの型式ﾗﾍﾞﾙが見え無い事", "FANｹｰﾌﾞﾙの向きに注意すること(ｺﾈｸﾀｰの向きに注意する事)", "ﾁｭｰﾌﾞの先端に合わせる" ], "Tolks": [ "締付ﾄﾙｸ 40cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :X軸ﾌｧﾝの型式確認", "WETE-G002-C09" ] }
{ "QualityItem": "型式確認･ｼﾘｱﾙ番号確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認､ｼﾘｱﾙNo.転記", "Method": "目視", "RecordMethod": "WETE-G002-C09", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立⑤", "WorkItems": [ "2. 1完成品にWASHER BOLT を取付ける", "1. にBOLT を挿入する", "3. 2完成品に をWASHER BOLT で取付" ], "WorkPoints": [ "WASHER をBOLT の方向に当てつけて取付ける事", " を矢印方向に押し当てる事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立⑥", "WorkItems": [ "1. PIN にBOLT WASHER を挿入する" ], "WorkPoints": [ "Dｶｯﾄ面" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "95cN･m", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立⑥", "WorkItems": [ "3. 2完成品にSCREW を取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立⑥", "WorkItems": [ "3. 2完成品にSCREW を取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立➆", "WorkItems": [ "■1. MOTOR の型式を確認し､ｼﾘｱﾙNoを検査書に記入する", "2. にMOTOR をBOLT WASHER で取付ける" ], "WorkPoints": [ "この作業では同じものを2個製作", "MOTOR のﾓｰﾀ線は左側から出る様に取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "型式", "Ser.No", "検査表 :X軸ﾓｰﾀのｼﾘｱﾙNo.の確認", "WETE-G002-C09" ] }
{ "QualityItem": "型式確認･ｼﾘｱﾙ番号確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認､ｼﾘｱﾙNo.転記", "Method": "目視", "RecordMethod": "WETE-G002-C09", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "ﾍｯﾄﾞﾌﾟﾚｰﾄ組立➆", "WorkItems": [ "■1. MOTOR の型式を確認し､ｼﾘｱﾙNoを検査書に記入する", "2. にMOTOR をBOLT WASHER で取付ける" ], "WorkPoints": [ "この作業では同じものを2個製作", "MOTOR のﾓｰﾀ線は左側から出る様に取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "型式", "Ser.No", "検査表 :X軸ﾓｰﾀのｼﾘｱﾙNo.の確認", "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立①", "WorkItems": [ "1. LINEAR-SCALE の型式を確認し､ｼﾘｱﾙNo.を検査書に転記する", "2. 橙色の斜線部分に砥石をかける", "3. BRACKET にBOLT WASHER を差込む", "4. BRACKET にLINEAR-SCALE (ﾍｯﾄﾞ)をBOLT で取付ける" ], "WorkPoints": [ "読取り面には触ら無い事", "読取り面を上にして取付ける事", "読取り面", "矢印方向に当付ける", "線に合わせて取付ける", "LINEAR-SCALE のﾍｯﾄﾞ及びｽｹｰﾙのｼﾘｱﾙNo.を転記する" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "Ser.No.型式", "S/N ※※※※※※※", "Model ST748C-0980E-PF", "この作業では同じものを2個製作", "検査表LINEAR-SCALE :ﾘﾆｱｽｹｰﾙのｼﾘｱﾙNo.の確認", "WETE-G002-C09" ] }
{ "QualityItem": "型式確認･ｼﾘｱﾙ番号確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認､ｼﾘｱﾙNo.転記", "Method": "目視", "RecordMethod": "WETE-G002-C09", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｱﾙｶﾝｻｽ", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立①", "WorkItems": [ "1. LINEAR-SCALE の型式を確認し､ｼﾘｱﾙNo.を検査書に転記する", "2. 橙色の斜線部分に砥石をかける", "3. BRACKET にBOLT WASHER を差込む", "4. BRACKET にLINEAR-SCALE (ﾍｯﾄﾞ)をBOLT で取付ける" ], "WorkPoints": [ "LINEAR-SCALE のﾍｯﾄﾞ及びｽｹｰﾙのｼﾘｱﾙNo.を転記する" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "Ser.No.型式", "S/N ※※※※※※※", "Model ST748C-0980E-PF", "この作業では同じものを2個製作", "検査表LINEAR-SCALE :ﾘﾆｱｽｹｰﾙのｼﾘｱﾙNo.の確認" ] }
{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "傷、ﾊﾞﾘ等無き事", "Method": "ｱﾙｶﾝｻｽ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "定盤", "Size": "", "ToolOther": "", "WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立①", "WorkItems": [ "1. LINEAR-SCALE の型式を確認し､ｼﾘｱﾙNo.を検査書に転記する", "2. 橙色の斜線部分に砥石をかける", "3. BRACKET にBOLT WASHER を差込む", "4. BRACKET にLINEAR-SCALE (ﾍｯﾄﾞ)をBOLT で取付ける" ], "WorkPoints": [ "LINEAR-SCALE のﾍｯﾄﾞ及びｽｹｰﾙのｼﾘｱﾙNo.を転記する" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "Ser.No.型式", "S/N ※※※※※※※", "Model ST748C-0980E-PF", "この作業では同じものを2個製作", "検査表LINEAR-SCALE :ﾘﾆｱｽｹｰﾙのｼﾘｱﾙNo.の確認" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "1回/3年", "ToolRecord": "校正成績書", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立①", "WorkItems": [ "1. LINEAR-SCALE の型式を確認し､ｼﾘｱﾙNo.を検査書に転記する", "2. 橙色の斜線部分に砥石をかける", "3. BRACKET にBOLT WASHER を差込む", "4. BRACKET にLINEAR-SCALE (ﾍｯﾄﾞ)をBOLT で取付ける" ], "WorkPoints": [ "LINEAR-SCALE のﾍｯﾄﾞ及びｽｹｰﾙのｼﾘｱﾙNo.を転記する" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "Ser.No.型式", "S/N ※※※※※※※", "Model ST748C-0980E-PF", "この作業では同じものを2個製作", "検査表LINEAR-SCALE :ﾘﾆｱｽｹｰﾙのｼﾘｱﾙNo.の確認" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "110cN･m", "WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立②", "WorkItems": [ "3. 2完成品の配線を㉙インシュロックで固定する" ], "WorkPoints": [ "ｲﾝｼｭﾛｯｸの頭位置", "配線をﾏｰｸ位置で固定する(適度な余裕がある事)", "ｲﾝｼｭﾛｯｸの頭位置に注意する事", "板金に平行に取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 110cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "110cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ組立②", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｱﾙｶﾝｻｽ", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立①", "WorkItems": [ "1. BLOCK のGREASE-NIPPLE JOINT 取付面にｱﾙｶﾝｻｽをかける", "2. BLOCK にGREASE-NIPPLE を取付ける" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを8個製作" ] }
{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "傷、ﾊﾞﾘ等無き事", "Method": "ｱﾙｶﾝｻｽ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "7㎜", "ToolOther": "150cN･m", "WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立①", "WorkItems": [ "1. BLOCK のGREASE-NIPPLE JOINT 取付面にｱﾙｶﾝｻｽをかける", "2. BLOCK にGREASE-NIPPLE を取付ける" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを8個製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "8㎜", "ToolOther": "110cN･m", "WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立①", "WorkItems": [], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 150cN･m", "締付ﾄﾙｸ 110cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "110cN･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立銘板", "WorkItems": [ "1. BRACKET BRACKET にLABEL LABEL を貼付ける" ], "WorkPoints": [ "この作業では同じものを2個製作", "LABEL LABEL の向きに注意する", "A矢視", "貼付けを行う前にｱﾙｺｰﾙで脱脂する事", "B矢視" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "B矢視", "8㎜", "18㎜", "A矢視", "30㎜", "5㎜", "7㎜", "1.5㎜", "7㎜", "1.5㎜" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾄﾞﾛｱｺﾈｸﾀｰ組立", "WorkItems": [ "2. COUPLER にBRACKET をSPACER BOLT WASHER で取付ける", "1. BRACKET にLABEL を貼付ける" ], "WorkPoints": [ "貼付け前に脱脂する事", "BRACKET の向きに注意する事" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ﾍｯﾄﾞﾄﾞﾛｱｺﾈｸﾀｰ組立", "WorkItems": [ "3. 2完成品にBRACKET BRACKET をBOLT で仮付けする" ], "WorkPoints": [ "本締工程:SD-A051867-046" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "11㎜", "7㎜" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｱﾙｶﾝｻｽ", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立②", "WorkItems": [ "1. にCOVER を貼付ける", "2. にSHEET SHEET を貼付ける" ], "WorkPoints": [ "ﾊﾞﾘの確認(ある場合はｱﾙｶﾝｻｽをかける)", "COVER の取付位置を脱脂する事", "青色の線で面を合わせる", "貼付け面は脱脂する事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作", "▲特殊作業" ] }
{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "傷、ﾊﾞﾘ等無き事", "Method": "ｱﾙｶﾝｻｽ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立②", "WorkItems": [ "1. にCOVER を貼付ける", "2. にSHEET SHEET を貼付ける", "1. にCOVER を貼付ける", "2. にSHEET SHEET を貼付ける" ], "WorkPoints": [ "ﾊﾞﾘの確認(ある場合はｱﾙｶﾝｻｽをかける)", "COVER の取付位置を脱脂する事", "青色の線で面を合わせる", "貼付け面は脱脂する事", "ﾊﾞﾘの確認(ある場合はｱﾙｶﾝｻｽをかける)", "COVER の取付位置を脱脂する事", "青色の線で面を合わせる", "貼付け面は脱脂する事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作", "▲特殊作業", "この作業では同じものを2個製作" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立②", "WorkItems": [ "1. にCOVER を貼付ける", "2. にSHEET SHEET を貼付ける", "▲3. 2完成品にWASHER を貼付ける" ], "WorkPoints": [ "ﾊﾞﾘの確認(ある場合はｱﾙｶﾝｻｽをかける)", "COVER の取付位置を脱脂する事", "青色の線で面を合わせる", "貼付け面は脱脂する事", "接着剤塗布 ｺﾞﾏ粒:2", "中心を合わせる" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "3mm", "この作業では同じものを2個製作", "1mm" ] }
{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ｺﾞﾏ粒:2", "Method": "目視", "RecordMethod": "-", "Other": "ﾛｯｸﾀｲﾄ415", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｱﾙｶﾝｻｽ", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立③", "WorkItems": [ "1. に をSCREW WASHER BOLT で仮付けする", "2. 1完成品にWASHER BOLT を固定する" ], "WorkPoints": [ "面に合わして仮付けする(黄緑色線)", "ﾊﾞﾘの確認(ある場合はｱﾙｶﾝｻｽをかける)" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "傷、ﾊﾞﾘ等無き事", "Method": "ｱﾙｶﾝｻｽ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立③", "WorkItems": [ "3. 2完成品をWASHER BOLT で固定する", "3. 2完成品をWASHER BOLT で固定する" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 160cN･m", "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 160cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "160cN･m", "WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立③", "WorkItems": [ "3. 2完成品をWASHER BOLT で固定する" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 160cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "160cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立④", "WorkItems": [ "1. にCOVER COVER COVER COVER を貼付ける", "3. に2完成品を挿入しSPACER を締め付ける", "2. SPACER にSCREW を挿入する" ], "WorkPoints": [ "貼付位置を脱脂する事", "SCREW が12㎜になる様にする事", "挿入方向:六角穴が上" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "2㎜", "2㎜", "3㎜", "この作業では同じものを2個製作", "2㎜", "12㎜", "3㎜", "2㎜", "2㎜" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "BOX7㎜", "ToolOther": "194cN･m", "WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立④", "WorkItems": [], "WorkPoints": [ "SCREW が12㎜になる様にする事", "挿入方向:六角穴が上" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "2㎜", "12㎜", "3㎜", "2㎜", "2㎜" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "110cN･m", "WorkName": "ﾍｯﾄﾞﾌﾞﾗｹｯﾄ組立⑤", "WorkItems": [ "1. にCLIP をBOLT で取付ける", "1. にCLIP をBOLT で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 110cN･m", "締付ﾄﾙｸ 110cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "CLIP の取付位置(向き)に気を付ける事", "この作業では同じものを2個製作", "CLIP の取付位置(向き)に気を付ける事", "この作業では同じものを2個製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "110cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null