input stringclasses 1
value | instruction stringlengths 222 1.92k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｽﾀﾝﾄﾞ部組込①",
"WorkItems": [
"1. STAND にPIN を圧入する",
"2. 1.完成品にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"片方のみ",
"出代:5㎜",
"ﾋﾟﾝ穴ｾﾝﾀｰ狙いで固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾀﾝﾄﾞ部組込②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "空圧部組込",
"WorkItems": [
"1. にCABLE を で取付ける",
"2. に1.完成品と を で取付ける",
"3. 2.完成品に を取付ける",
"5. 4.完成品に を ㉒で取付ける",
"4. 3.完成品に を で取付ける"
],
"WorkPoints": [
"矢視A",
"底面"
],
"Tolks": [],
"InspectionNo":... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部組立⑤",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNO.を記入する",
"2. 1.完成品にLABEL TERMINAL PROCESS を取付ける",
"3. に をBOLT で取付ける",
"4. 3完成品に2.完成品をBOLT WASHER で取付ける",
"5. 4.完成品に を取付ける"
],
"WorkPoints": [
"型式:MSMD012... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-081",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部組立⑤",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNO.を記入する",
"2. 1.完成品にLABEL TERMINAL PROCESS を取付ける",
"3. に をBOLT で取付ける",
"4. 3完成品に2.完成品をBOLT WASHER で取付ける",
"5. 4.完成品に を取付ける"
],
"WorkPoints": [
"型式:MSMD012... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-081",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾓｰﾀ原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "ｱｸﾁｭｴｰﾀ部調整",
"WorkItems": [
"4. ﾌﾟｰﾘを固定する",
"3. ブラケットの原点位置合わせ穴に㉗を挿入し プレートを押し当てる",
"2. ﾓｰﾀ軸を回してZ相原点『00』位置にする",
"1. ﾓｰﾀに原点出し治具を接続する"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄ"
],
"Tolks": [],
"Inspection... | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-081",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "位置合せ治具",
"Size": "",
"ToolOther": "FM-4606",
"WorkName": "ｱｸﾁｭｴｰﾀ部調整",
"WorkItems": [],
"WorkPoints": [
"ﾋﾟﾝ当てにて固定",
"ｼｬﾌﾄ",
"ﾌﾟﾚｰﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :MTY軸 原点確認"
]
} | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-4606",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部調整",
"WorkItems": [],
"WorkPoints": [
"ﾍﾞﾙﾄ張力 276~321Hz"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"上下"
]
} | {
"QualityItem": "ﾍﾞﾙﾄﾃﾝｼｮﾝ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "276~321Hz",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "反転ﾍｯﾄﾞ上下駆動部組込",
"WorkItems": [
"1. に をBOLT で取付ける",
"2. 1.完成品にCABLE を接続し引き回す"
],
"WorkPoints": [
"矢視A",
"矢視B"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-112",
"InspectionItems": [
"検査表 :接続確認"
],
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-112",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部配線①",
"WorkItems": [
"1. にCABLE CABLE CABLE CABLE を接続し引き回す"
],
"WorkPoints": [
"D1500"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :接続確認",
"ｲﾝｼ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-112",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀ部配線②",
"WorkItems": [
"1. にCABLE CABLE CABLE CABLE を接続し引き回す"
],
"WorkPoints": [
"他の箇所の結束は､ｸﾘｰﾝｹｰﾌﾞﾙと合わせて行う"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"I... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-112",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾘｰﾝｹｰﾌﾞﾙ組込",
"WorkItems": [
"1. BRACKET にSHEET を貼付ける",
"3. 2.完成品にCABLE をBOLT で取付ける"
],
"WorkPoints": [
"端面合わせ",
"ｸﾘｰﾝｹｰﾌﾞﾙ取り扱い注意 ｸﾘｰﾝｹｰﾌﾞﾙはﾕﾆｯﾄ組立が完了するまでｴｱﾏｯﾄ等で保護すること ※汚れが付くと浸み込む為取ることが出来ません"
],
"Tolks": []... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾘｰﾝｹｰﾌﾞﾙ空圧側配線",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-112"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-112",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾘｰﾝｹｰﾌﾞﾙ空圧側配線",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾘｰﾝｹｰﾌﾞﾙ本体側配線",
"WorkItems": [
"1. ｸﾘｰﾝｹｰﾌﾞﾙ本体側の配線配管を引き回す"
],
"WorkPoints": [
"φ6白 →V21φ6黒 →P21",
"ICTR4RCN22K3131CN23K3131ICTR11R",
"目印ﾗﾍﾞﾙを貼付けておく"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾀﾝﾄﾞ部配線",
"WorkItems": [
"1. にCABLE を接続し引き回す"
],
"WorkPoints": [
"D1500"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :接続確認",
"1B10910R",
"ICTR10R... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-112",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰ部配線",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-112"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-112",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着反転ﾍｯﾄﾞ上下駆動部組立①",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNO.を記入する",
"2. 1.完成品にLABEL TERMINAL PROCESS を取付ける",
"3. PLATE に1.完成品をBOLT WASHER で仮締めし､ﾓｰﾀｰ軸側からBEARING を挿入後､BOLT WASHER を本締めする"
],
"WorkPoints": [
"ﾓｰﾀｰ線(4P):IH... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-083",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着反転ﾍｯﾄﾞ上下駆動部組立①",
"WorkItems": [
"■1. MOTOR の型式を確認し､ｼﾘｱﾙNO.を記入する",
"2. 1.完成品にLABEL TERMINAL PROCESS を取付ける",
"3. PLATE に1.完成品をBOLT WASHER で仮締めし､ﾓｰﾀｰ軸側からBEARING を挿入後､BOLT WASHER を本締めする"
],
"WorkPoints": [
"ﾓｰﾀｰ線(4P):IH... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-083",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "原点出し用ﾋﾟﾝ",
"Size": "φ3",
"ToolOther": "FM-3468",
"WorkName": "仮圧着反転ﾍｯﾄﾞ上下駆動部組立②",
"WorkItems": [
"1. にCAM BLOCK をBOLT で取付ける"
],
"WorkPoints": [
"φ3ﾋﾟﾝを挿入し､ｶﾑを固定する",
"ﾓｰﾀｰZ相位置にて､ｶﾑとﾓｰﾀｰを固定する",
"φ3ﾋﾟﾝ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItem... | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3468",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-083",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着反転ﾍｯﾄﾞ上下駆動部組立③",
"WorkItems": [
"3. 1.完成品に2.完成品をBOLT WASHER で取付ける",
"2. BRACKET にSENSOR をBOLT WASHER WASHER で取付ける",
"1. にDOG をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"Inspection... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着反転ﾍｯﾄﾞ上下駆動部組立④",
"WorkItems": [
"5. 次工程(仮圧着移載駆動部)へ支給する",
"◆4. 3.完成品のｶﾑ部にｸﾞﾘｰｽを塗布する",
"3. 2.完成品にCOVER をBOLT WASHER で取付ける",
"2. 1.完成品にCOVER をBOLT WASHER で取付ける",
"1. にSPACER をSCREW で取付ける"
],
"WorkPoints": [
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TCP認識照明組立①",
"WorkItems": [
"1. BRACKET にBRACKET をBOLT ･WASHER で組付けCABLE-SUPPORT を挿入",
"■2. LED LIGHTING UNIT の型式を確認しｼﾘｱﾙ番号を検査書に記入",
"3. LED LIGHTING UNIT にOPTICAL-FILTER を隙間のないように当付けて組付け"
],
"WorkPoints": [
"0.02㎜以下"
... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-088",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TCP認識照明組立①",
"WorkItems": [
"1. BRACKET にBRACKET をBOLT ･WASHER で組付けCABLE-SUPPORT を挿入",
"■2. LED LIGHTING UNIT の型式を確認しｼﾘｱﾙ番号を検査書に記入",
"3. LED LIGHTING UNIT にOPTICAL-FILTER を隙間のないように当付けて組付け"
],
"WorkPoints": [
"0.02㎜以下"
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-088",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "0.02㎜以下",
"WorkName": "TCP認識照明組立①",
"WorkItems": [
"1. BRACKET にBRACKET をBOLT ･WASHER で組付けCABLE-SUPPORT を挿入",
"■2. LED LIGHTING UNIT の型式を確認しｼﾘｱﾙ番号を検査書に記入",
"3. LED LIGHTING UNIT にOPTICAL-FILTER を隙間のないように当付けて組付け"
],
"WorkPoints": [... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.02㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-088",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "TCP認識照明組立②",
"WorkItems": [
"1. に を検査書の組付け寸法にて組付け"
],
"WorkPoints": [
"183±1㎜",
"正流れの場合",
"逆流れの場合",
"正流れ･逆流れで配線の向きが違うので注意",
"正流れの場合",
"逆流れの場合"
],
"Tolks": [],
"InspectionNo": "",
"Ins... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "183㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ICﾄﾚｲｽﾃｰｼﾞ部へ払い出し",
"WorkItems": [
"1. ･SPACER ･BOLT ･WASHER ･SCREW をICﾄﾚｲｽﾃｰｼﾞ部へ払い出し"
],
"WorkPoints": [
"MTKA044761 305CG:ICﾄﾚｲｽﾃｰｼﾞ部 又は MTKA044762 305CG逆流れ:ICﾄﾚｲｽﾃｰｼﾞ部 へ払い出し"
],
"Tolks": [],
"InspectionNo": "",
"I... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立①",
"WorkItems": [
"▲1. PLATE にSPACER SPACER SPACER SPACER SPACER SPACER SPACER SPACER をSCREW SCREW で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words"... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立②",
"WorkItems": [
"1. にCABLE-SUPPORT ･CABLE ･CABLE をBOLT ･WASHER ･WASHER で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θ軸部組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"出代:9mm",
"底面図",
"出代:3mm"
]
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θ軸部組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"出代:9mm",
"底面図",
"出代:3mm"
]
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:9.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立②",
"WorkItems": [
"1. PULLEY にDOG をBOLT WASHER で組付け",
"2. 1.完成品にBOLT WASHER を組付け"
],
"WorkPoints": [
"方向注意!!円の接線に平行に組付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θ軸部組立③",
"WorkItems": [
"1. HOUSING にPIN を圧入",
"2. 1.完成品にBEARING を挿入し をBOLT WASHER で組付け",
"3. BLOCK にSTOPPER を組付け",
"4. 2.完成品に3.完成品をBOLT で組付け",
"1. HOUSING にPIN を圧入",
"2. 1.完成品にBEARING を挿入し をBOLT WASHER で組付け... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代(合計8個):3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立④",
"WorkItems": [
"2. にLINEAR-WAY をDﾋﾟﾝに押し当ててBOLT で組付け",
"3. 2.完成品にPOST をNUT で組付け",
"1. LINEAR-WAY の型式を確認しｼﾘｱﾙ番号(ﾛｯﾄ番号)を検査書に記載"
],
"WorkPoints": [
"4面共組付け(計4個)",
"上側で端面合わせ",
"ｽﾗｲﾀﾞｰ基準面側をDﾋﾟﾝ側に押し当てて組付け"... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立④",
"WorkItems": [
"2. にLINEAR-WAY をDﾋﾟﾝに押し当ててBOLT で組付け",
"3. 2.完成品にPOST をNUT で組付け",
"1. LINEAR-WAY の型式を確認しｼﾘｱﾙ番号(ﾛｯﾄ番号)を検査書に記載"
],
"WorkPoints": [
"4面共組付け(計4個)",
"上側で端面合わせ",
"ｽﾗｲﾀﾞｰ基準面側をDﾋﾟﾝ側に押し当てて組付け"... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "1.2~1.5N･m",
"WorkName": "θ軸部組立④",
"WorkItems": [],
"WorkPoints": [
"4面共組付け(計4個)",
"上側で端面合わせ",
"ｽﾗｲﾀﾞｰ基準面側をDﾋﾟﾝ側に押し当てて組付け",
"4面共組付け(計4個)"
],
"Tolks": [
"締付ﾄﾙｸ 1.2~1.5N･m"
],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2~1.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立④",
"WorkItems": [
"2. にLINEAR-WAY をDﾋﾟﾝに押し当ててBOLT で組付け",
"3. 2.完成品にPOST をNUT で組付け",
"1. LINEAR-WAY の型式を確認しｼﾘｱﾙ番号(ﾛｯﾄ番号)を検査書に記載"
],
"WorkPoints": [
"4面共組付け(計4個)",
"上側で端面合わせ",
"ｽﾗｲﾀﾞｰ基準面側をDﾋﾟﾝ側に押し当てて組付け"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立⑤",
"WorkItems": [
"1. のｼｬﾌﾄに COLLAR BEARING を挿入しBOLT WASHER で組付け"
],
"WorkPoints": [
"COLLAR は を挿入後BEARING を組付ける前に挿入",
" はﾄﾞｸﾞとｽﾄｯﾊﾟｰの位置関係に注意して挿入すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸部組立⑥",
"WorkItems": [
"1. にT-BELT を取付",
"2. 1.完成品にSENSOR をBOLT WASHER WASHER で取付"
],
"WorkPoints": [
"ﾄﾞｸﾞの下側に通すこと",
"ﾎﾟｽﾄの穴にｾﾝｻの突起を挿し込む"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸駆動部組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-089",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-089"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸駆動部組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-089",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-089"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "θ軸駆動部組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸駆動部組立②",
"WorkItems": [
"1. PLATE に をBOLT WASHER で組付け",
"2. 1.完成品にBOLT NUT を仮止め"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"仮止め:S... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸駆動部組立③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "θ軸駆動部組立④",
"WorkItems": [
"2. 1.完成品にJOINT JOINT をBOLT で取付"
],
"WorkPoints": [
"SD-A044761-010, 011で仮止めしていたﾎﾞﾙﾄを本締めすること",
"ﾍﾞﾙﾄﾃﾝｼｮﾝ:234~267Hz",
"ﾄﾞｸﾞは原点ｾﾝｻｰに対し下記寸法を目安とする｡"
],
"Tolks": [],
"Inspecti... | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "",
"WorkName": "θ軸駆動部組立④",
"WorkItems": [
"2. 1.完成品にJOINT JOINT をBOLT で取付"
],
"WorkPoints": [
"SD-A044761-010, 011で仮止めしていたﾎﾞﾙﾄを本締めすること",
"ﾍﾞﾙﾄﾃﾝｼｮﾝ:234~267Hz",
"ﾄﾞｸﾞは原点ｾﾝｻｰに対し下記寸法を目安とする｡"
],
"Tolks": [],
"InspectionNo":... | {
"QualityItem": "ﾍﾞﾙﾄﾃﾝｼｮﾝ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "234~267Hz",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "3.5㎜",
"ToolOther": "",
"WorkName": "θ軸駆動部組立④",
"WorkItems": [
"2. 1.完成品にJOINT JOINT をBOLT で取付"
],
"WorkPoints": [
"SD-A044761-010, 011で仮止めしていたﾎﾞﾙﾄを本締めすること",
"ﾍﾞﾙﾄﾃﾝｼｮﾝ:234~267Hz",
"ﾄﾞｸﾞは原点ｾﾝｻｰに対し下記寸法を目安とする｡"
],
"Tolks": [],
"Inspect... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:3.5㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立①",
"WorkItems": [
"1. CYLINDER CYLINDER にJOINT を組付け"
],
"WorkPoints": [
"この作業では同じものを2個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立②",
"WorkItems": [
"1. BRACKET BRACKET にSENSOR SENSOR をBOLT WASHER WASHER で組付け"
],
"WorkPoints": [
"この作業ではL･R用それぞれ1個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words":... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立③",
"WorkItems": [
"1. PLATE にSENSOR をBOLT ･WASHER ･WASHER で組付け",
"2. BRACKET ･BRACKET にSENSOR をBOLT ･WASHER ･WASHER で組付け",
"3. 2.完成品に1.完成品・SPACER をBOLT ・WASHER ・BOLT ・㉒で組付け"
],
"WorkPoints": [
"この作業ではL･R用それぞれ1個作成... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降部組立④",
"WorkItems": [
"1. PLATE に STOPPER をBOLT WASHER で組付け",
"2. 1.完成品にPLATE SCREW をBOLT で組付け"
],
"WorkPoints": [
"この作業ではL･R用それぞれ1個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:12.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立⑤",
"WorkItems": [
"1. に をBOLT WASHER で組付け",
"2. 1.完成品にPLATE STOPPER をBOLT で組付け"
],
"WorkPoints": [
"PLATE を組付け後にSTOPPER を組付け",
"この作業ではL･R用それぞれ1個作成",
"PLATE を組付け後にSTOPPER を組付け"
],
"Tolks": [],
"Ins... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立⑥",
"WorkItems": [
"1. にDOG DOG をBOLT WASHER で組付け",
"2. 1.完成品に をBOLT WASHER で組付け"
],
"WorkPoints": [
"この作業ではL･R用それぞれ1個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立⑦",
"WorkItems": [
"1. ･ に ･ ･CABLE-SUPPORT をBOLT で組付け"
],
"WorkPoints": [
"この作業ではL･R用それぞれ1個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"L用",
"R用"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降部組立⑧",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降部組立⑨",
"WorkItems": [
"2. BRACKET にPIN を圧入",
"1. BLOCK にSCREW を組付け",
"3. 2.完成品にPOST をNUT で組付け"
],
"WorkPoints": [
"この作業ではそれぞれ4個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.7㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降部組立⑨",
"WorkItems": [
"2. BRACKET にPIN を圧入",
"1. BLOCK にSCREW を組付け",
"3. 2.完成品にPOST をNUT で組付け"
],
"WorkPoints": [
"この作業ではそれぞれ4個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降部組立⑨",
"WorkItems": [
"2. BRACKET にPIN を圧入",
"1. BLOCK にSCREW を組付け",
"3. 2.完成品にPOST をNUT で組付け"
],
"WorkPoints": [
"この作業ではそれぞれ4個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:19.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降部組立⑩",
"WorkItems": [
"2. 1.完成品にSTOPPER をNUT で組付け",
"1. に をBOLT ･WASHER で組付け",
"3. 2.完成品にLABEL を貼付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wo... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:13.7㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降部組立⑩",
"WorkItems": [
"2. 1.完成品にSTOPPER をNUT で組付け",
"1. に をBOLT ･WASHER で組付け",
"3. 2.完成品にLABEL を貼付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wo... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立⑪",
"WorkItems": [
"2. 1.完成品にSPRING を組付け",
"1. に ･ ･ ･ をBOLT ･WASHER で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"Dﾋﾟﾝ押当て",
"4面共組付... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立⑫",
"WorkItems": [
"1. に をBOLT で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"A-A断面図"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部組立⑬",
"WorkItems": [
"1. に の配管を接続しBOLT WASHER で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"上面図",
" 配管",
" 配管",
" 配管",
" 配... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "昇降部組立⑭",
"WorkItems": [
"1. の原点位置でのﾌﾟﾚｰﾄ平面度確認"
],
"WorkPoints": [
"平面度 0.05mm以下"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾌﾟﾚｰﾄ平面度確認",
... | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.05㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-089",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部配線①",
"WorkItems": [
"1. にCABLE CABLE CABLE LABEL TERMINAL PROCESS を取付"
],
"WorkPoints": [
"合わせる",
"合わせる"
],
"Tolks": [
"KEYENCE PR-MB30N1の配線に取付",
"KEYENCE PR-MB30N1の配線に取付"
],
"InspectionNo": "",
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-115",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部配線②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-115",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-115"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-115",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降部配線③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-115"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-115",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線用ﾌﾞﾗｹｯﾄ組立①",
"WorkItems": [
"1. BRACKET にSWITCH をBOLT WASHER で組付け",
"2. 1.完成品にJOINT を組付け"
],
"WorkPoints": [
"この作業ではそれぞれ2個作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線用ﾌﾞﾗｹｯﾄ組立②",
"WorkItems": [
"1. SPEED-CONTROLLER のｽﾋﾟｺﾝを調整",
"2. に2.完成品･BRACKET をにBRACKET をBOLT WASHER WASHER で組付け"
],
"WorkPoints": [
"この作業ではL･R用を作成",
"ｽﾋﾟｺﾝ:全閉から2回転開く",
"この作業では8個作成"
],
"Tolks": [],
"... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "全閉から2回転開く",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "配線用ﾌﾞﾗｹｯﾄ組立③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線用ﾌﾞﾗｹｯﾄ組立④",
"WorkItems": [
"▲1. BRACKET にSPACER SPACER をBOLT WASHER でADHESIVE ﾛｯｸﾀｲﾄを塗布して組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"裏側",
... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線用ﾌﾞﾗｹｯﾄ組立⑤",
"WorkItems": [
"1. PLATE にBRACKET をBOLT WASHER で組付け",
"2. 1.完成品にCABLE-SUPPORT を組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TCP認識照明部取付",
"WorkItems": [
"1. にSPACER をSCREW で組付け",
"2. 定盤上で1.完成品に をBOLT ㉒で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"定盤上で組付け",
"1.完... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線用ﾌﾞﾗｹｯﾄ取付①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線用ﾌﾞﾗｹｯﾄ取付②",
"WorkItems": [
"1. に をBOLT WASHER で組付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"A 断面図"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "真空部配線",
"WorkItems": [
"1. にCABLE CABLE を接続"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"A 断面図",
"B11016R",
"検査表 :接続確認 (3)ICﾄﾚｲｽﾃｰｼﾞ部(正流れｽﾃｰ... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-115",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ組立①",
"WorkItems": [
"1. FRAME にSUPPORT NUT NUT CABLE-SUPPORT を挿入"
],
"WorkPoints": [
"挿入面は上図参照",
"1 のB･D面対象品"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wor... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ組立②",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT ･NUT ･CABLE-SUPPORT を挿入"
],
"WorkPoints": [
"挿入面は上図参照",
"1 のB･D面対象品"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ組立③",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT ･NUT を挿入"
],
"WorkPoints": [
"挿入面は上図参照",
"1 のA･C面対象品"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ組立⑤",
"WorkItems": [
"1. FRAME にSUPPORT NUT NUT を挿入"
],
"WorkPoints": [
"挿入面は上図参照"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"D面",
"C面",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ組立⑥",
"WorkItems": [
"1. をBRACKET WASHER BOLT で組付け"
],
"WorkPoints": [
"端面合わせ",
"WASHER の方向に注意",
"ｴｯｼﾞあり",
"丸みを帯びている",
"定盤上で平面に組付けの事",
"BRACKET は組付けの向きに注意",
"左外側の組付け"
],
"Tolks": []... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ組立⑦",
"WorkItems": [
"1. ･ ･ ･ をBRACKET ･WASHER ･BOLT で組付け"
],
"WorkPoints": [
"端面合わせ",
"WASHER の方向に注意",
"ｴｯｼﾞあり",
"丸みを帯びている",
"定盤上で平面に組付けの事",
"BRACKET は組付けの向きに注意",
"右外側の組付け"
],
"Tolks... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ組立⑧",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ組立⑨",
"WorkItems": [
"1. にBRACKET をWASHER BOLT WASHER で組付け"
],
"WorkPoints": [
"WASHER の方向に注意",
"ｴｯｼﾞあり",
"丸みを帯びている",
"定盤上で平面に組付けの事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ組立⑩",
"WorkItems": [
"▲1. COVER にBUSH をADHESIVE で接着",
"2. にBRACKET をBOLT WASHER で取付し､CABLE-SUPPORT を挿入",
"3. 2.完成品に1.完成品･COVER BRACKET をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:5",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ415",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ組立⑪",
"WorkItems": [
"▲1. COVER にBUSH をADHESIVE で接着",
"2. に1.完成品･COVER をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:5",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ415",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ICﾄﾚｲｽﾄｯｶｰ供給・収納共通部組立①",
"WorkItems": [
"1. BLOCK ･BLOCK にPIN を圧入",
"2. 1.完成品にPOST をNUT で組付"
],
"WorkPoints": [
"各4ｾｯﾄ組立の事",
"出代 9.5mm±0.5mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "ﾃﾞｼﾞﾀﾙ",
"WorkName": "ICﾄﾚｲｽﾄｯｶｰ供給・収納共通部組立①",
"WorkItems": [
"1. BLOCK ･BLOCK にPIN を圧入",
"2. 1.完成品にPOST をNUT で組付"
],
"WorkPoints": [
"各4ｾｯﾄ組立の事",
"出代 9.5mm±0.5mm"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-090",
"In... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "ﾊﾞﾈﾎﾟｽﾄ出代:9.5㎜±0.5㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WWYJ-5300-090",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ICﾄﾚｲｽﾄｯｶｰ供給・収納共通部組立②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ICﾄﾚｲｽﾄｯｶｰ供給・収納共通部組立③",
"WorkItems": [
"1. にDOG DOG をBOLT で組付け"
],
"WorkPoints": [
"各4ｾｯﾄ組立の事",
"幅の広い方がこちらになる様に取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ICﾄﾚｲｽﾄｯｶｰ供給・収納共通部組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-090",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-090"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "寸法:24.5㎜±0.2㎜以内",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "WWYJ-5300-090",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ICﾄﾚｲｽﾄｯｶｰ供給・収納共通部組立⑤",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ICﾄﾚｲｽﾄｯｶｰ供給・収納共通部組立⑥",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ICﾄﾚｲｽﾄｯｶｰ供給・収納共通部組立⑦",
"WorkItems": [
"2. にLINEAR-WAY をD-PINに押し当ててBOLT で組付け",
"1. LINEAR-WAY の･型式確認 しｼﾘｱﾙNo記録",
"3. 2.完成品に をｽﾗｲﾀﾞｰ基準面にD-PINを押し当ててBOLT で組付け､SPRING を取付",
"4. 3.完成品の仮止めしていたドグを㉙ブロックゲージを挟んで水平に組付け"
],
"Wor... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-090",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ICﾄﾚｲｽﾄｯｶｰ供給・収納共通部組立⑦",
"WorkItems": [
"2. にLINEAR-WAY をD-PINに押し当ててBOLT で組付け",
"1. LINEAR-WAY の･型式確認 しｼﾘｱﾙNo記録",
"3. 2.完成品に をｽﾗｲﾀﾞｰ基準面にD-PINを押し当ててBOLT で組付け､SPRING を取付",
"4. 3.完成品の仮止めしていたドグを㉙ブロックゲージを挟んで水平に組付け"
],
"Wor... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-090",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "0.01㎜",
"WorkName": "ICﾄﾚｲｽﾄｯｶｰ供給・収納共通部組立⑦",
"WorkItems": [],
"WorkPoints": [
"･型式確認 ･ｼﾘｱﾙNo記録"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LINEAR-WAY :重要部品確認",
"0.01㎜が... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.01㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-090",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "0.5㎜",
"WorkName": "ICﾄﾚｲｽﾄｯｶｰ供給・収納共通部組立⑦",
"WorkItems": [],
"WorkPoints": [
"･型式確認 ･ｼﾘｱﾙNo記録"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LINEAR-WAY :重要部品確認",
"0.01㎜が通... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:0.5㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ICﾄﾚｲｽﾄｯｶｰ供給・収納共通部組立⑧",
"WorkItems": [
"◆1. の指示部に㉖グリースを薄く塗布",
"2. に をBOLT WASHER で組付け"
],
"WorkPoints": [
"ベアリング外周に㉖グリースを塗布",
"各4ｾｯﾄ組立の事(供給L･R､収納L･R区分必要)",
"ﾁｬｯｸを取付けるまでは板金と接触する",
"先端ロッド外周に㉖グリースを塗布",
"... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ICﾄﾚｲｽﾄｯｶｰ供給部組立①",
"WorkItems": [
"1. PLATE PLATE にPIN を圧入",
"2. 1.完成品にSCREW が後ろ側に飛び出ないようにNUT で仮止め"
],
"WorkPoints": [
"各2ｾｯﾄ組立の事",
"SCREW が後ろ側に飛び出ない様注意の事",
"ｻﾞｸﾞﾘが無い面に圧入",
"ｻﾞｸﾞﾘが有る面"
],
"Tolks"... | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:4.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.