input stringclasses 1 value | instruction stringlengths 222 1.92k | output stringlengths 193 312 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付21(後面左上)",
"WorkItems": [
"■1. LABEL の記述内容を確認をする",
"2. COVER にLABEL を貼付ける"
],
"WorkPoints": [
"上下で穴寸法位置が違います",
"貼付前に脱脂する事",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"後面上左側",
"25mm",
">PC<",
"15mm",
"12mm",
"14mm",
"■安全作業",
"検査表LABEL :安全部品確認"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付22(後面中央右上)",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
">PC<",
"検査表LABEL :安全部品確認",
"後面中央右上",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付22(後面中央右上)",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
">PC<",
"検査表LABEL :安全部品確認",
"後面中央右上",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付23(後面中央右上)",
"WorkItems": [
"1. にCAP を取付ける"
],
"WorkPoints": [
"2個取付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
">PC<"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付24(前部開閉扉左側)",
"WorkItems": [
"■3. にLABEL LABEL LABEL を貼付ける",
"■2. LABEL LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"記述内容確認",
"型式:LABEL PD0101M1 ②PC010101 ③PC011701",
"貼付前に脱脂する事",
"2ｾｯﾄ貼付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表②:安全部品確認",
"検査表②:貼付位置確認",
"検査表LABEL :安全部品確認",
">PC<",
">PC<",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "①の型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付24(前部開閉扉左側)",
"WorkItems": [
"■3. にLABEL LABEL LABEL を貼付ける",
"■2. LABEL LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"記述内容確認",
"型式:LABEL PD0101M1 ②PC010101 ③PC011701",
"貼付前に脱脂する事",
"2ｾｯﾄ貼付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表②:安全部品確認",
"検査表②:貼付位置確認",
"検査表LABEL :安全部品確認",
">PC<",
">PC<",
"WWYJ-5300-007"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "⑥⑦⑧の型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-007",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付24(前部開閉扉左側)",
"WorkItems": [
"■3. にLABEL LABEL LABEL を貼付ける",
"■2. LABEL LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける",
"■3. にLABEL LABEL LABEL を貼付ける",
"■2. LABEL LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表②:安全部品確認",
"検査表LABEL :安全部品確認",
">PC<",
">PC<",
"■安全作業",
"検査表②:安全部品確認",
"検査表LABEL :安全部品確認",
">PC<",
">PC<"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付25(前部開閉扉右側)",
"WorkItems": [
"■3. にLABEL LABEL LABEL を貼付ける",
"■2. LABEL LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"記述内容確認",
"型式:LABEL PD0101M1 ②PC010101 ③PC011701",
"貼付前に脱脂する事",
"2ｾｯﾄ貼付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表②:安全部品確認",
"検査表②:貼付位置確認",
"検査表LABEL :安全部品確認",
">PC<",
">PC<",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "①の型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付25(前部開閉扉右側)",
"WorkItems": [
"■3. にLABEL LABEL LABEL を貼付ける",
"■2. LABEL LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"記述内容確認",
"型式:LABEL PD0101M1 ②PC010101 ③PC011701",
"貼付前に脱脂する事",
"2ｾｯﾄ貼付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表②:安全部品確認",
"検査表②:貼付位置確認",
"検査表LABEL :安全部品確認",
">PC<",
">PC<",
"WWYJ-5300-007"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "⑥⑦⑧の型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-007",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付25(前部開閉扉右側)",
"WorkItems": [
"■3. にLABEL LABEL LABEL を貼付ける",
"■2. LABEL LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける",
"■3. にLABEL LABEL LABEL を貼付ける",
"■2. LABEL LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表②:安全部品確認",
"検査表LABEL :安全部品確認",
"■安全作業",
"検査表②:安全部品確認",
"検査表LABEL :安全部品確認"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付26(後部扉左側)",
"WorkItems": [
"■3. にLABEL LABEL を貼付ける",
"■2. LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"記述内容確認",
"型式:LABEL PD0101M1 ②PC010101",
"貼付前に脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
">PC<",
"検査表②:安全部品確認",
"検査表②:貼付位置確認",
"検査表LABEL :安全部品確認",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "①の型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付26(後部扉左側)",
"WorkItems": [
"■3. にLABEL LABEL を貼付ける",
"■2. LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"記述内容確認",
"型式:LABEL PD0101M1 ②PC010101",
"貼付前に脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
">PC<",
"検査表②:安全部品確認",
"検査表②:貼付位置確認",
"検査表LABEL :安全部品確認",
"WWYJ-5300-007"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "⑥⑦⑧の型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-007",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付26(後部扉左側)",
"WorkItems": [
"■3. にLABEL LABEL を貼付ける",
"■2. LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける",
"■3. にLABEL LABEL を貼付ける",
"■2. LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認",
"型式:LABEL PD0101M1 ②PC010101",
"貼付前に脱脂する事",
"貼付前に脱脂する事",
"記述内容確認",
"型式:LABEL PD0101M1 ②PC010101",
"貼付前に脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
">PC<",
"検査表②:安全部品確認",
"検査表LABEL :安全部品確認",
"■安全作業",
">PC<",
"検査表②:安全部品確認",
"検査表LABEL :安全部品確認"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付27(本圧着ﾒﾝﾃﾅﾝｽｶﾊﾞｰ)",
"WorkItems": [
"■3. にLABEL を貼付ける",
"■2. LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"記述内容確認",
"型式:LABEL PC010101",
"貼付前に脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表②:安全部品確認",
"検査表②:貼付位置確認",
"検査表LABEL :安全部品確認",
">PC<",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "①の型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付27(本圧着ﾒﾝﾃﾅﾝｽｶﾊﾞｰ)",
"WorkItems": [
"■3. にLABEL を貼付ける",
"■2. LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"記述内容確認",
"型式:LABEL PC010101",
"貼付前に脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表②:安全部品確認",
"検査表②:貼付位置確認",
"検査表LABEL :安全部品確認",
">PC<",
"WWYJ-5300-007"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "⑥⑦⑧の型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-007",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付27(本圧着ﾒﾝﾃﾅﾝｽｶﾊﾞｰ)",
"WorkItems": [
"■3. にLABEL を貼付ける",
"■2. LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける",
"■3. にLABEL を貼付ける",
"■2. LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表②:安全部品確認",
"検査表LABEL :安全部品確認",
"■安全作業",
"検査表②:安全部品確認",
"検査表LABEL :安全部品確認"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付28(後面上中央)IC供給仕様",
"WorkItems": [
"2. COVER にLABEL LABEL LABEL LABEL LABEL LABEL を貼付ける",
"■1. LABEL の型式を確認をする"
],
"WorkPoints": [
"貼付前に脱脂する事",
"IC供給有りの場合実施する",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"後面上中央",
"■安全作業",
"検査表LABEL :安全部品確認",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "銘板貼付28(後面上中央)IC供給仕様",
"WorkItems": [
"2. COVER にLABEL LABEL LABEL LABEL LABEL LABEL を貼付ける",
"■1. LABEL の型式を確認をする"
],
"WorkPoints": [
"貼付前に脱脂する事",
"IC供給有りの場合実施する",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"後面上中央",
"■安全作業",
"検査表LABEL :安全部品確認"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付29(後面上中央)IC供給仕様",
"WorkItems": [
"■1. LABEL の型式確認をする",
"■2. にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"IC供給有りの場合実施する",
"型式:LABEL PW0102M1",
"±2㎜以下"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業",
"検査表 :安全部品確認",
"検査表 :貼付位置確認",
"WWYJ-5300-007"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "⑥⑦⑧の型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-007",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付29(後面上中央)IC供給仕様",
"WorkItems": [
"■1. LABEL の型式確認をする",
"■2. にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"IC供給有りの場合実施する",
"型式:LABEL PW0102M1",
"±2㎜以下"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業",
"検査表 :安全部品確認",
"検査表 :貼付位置確認"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付30(後部中央扉大)IC供給仕様",
"WorkItems": [
"■3. にLABEL LABEL を貼付ける",
"■2. LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"記述内容確認",
"型式:LABEL PD0101M1 ②PC010101",
"貼付前に脱脂する事",
"IC供給仕様時"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
">PC<",
"検査表②:安全部品確認",
"検査表②:貼付位置確認",
"検査表LABEL :安全部品確認",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "①の型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付30(後部中央扉大)IC供給仕様",
"WorkItems": [
"■3. にLABEL LABEL を貼付ける",
"■2. LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"記述内容確認",
"型式:LABEL PD0101M1 ②PC010101",
"貼付前に脱脂する事",
"IC供給仕様時"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
">PC<",
"検査表②:安全部品確認",
"検査表②:貼付位置確認",
"検査表LABEL :安全部品確認",
"WWYJ-5300-007"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "⑥⑦⑧の型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-007",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付30(後部中央扉大)IC供給仕様",
"WorkItems": [
"■3. にLABEL LABEL を貼付ける",
"■2. LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける",
"■3. にLABEL LABEL を貼付ける",
"■2. LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表②:安全部品確認",
"検査表LABEL :安全部品確認",
"■安全作業",
"検査表②:安全部品確認",
"検査表LABEL :安全部品確認"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付31(後部中央扉小)IC供給仕様",
"WorkItems": [
"■3. にLABEL LABEL を貼付ける",
"■2. LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"記述内容確認",
"型式:LABEL PD0101M1 ②PC010101",
"貼付前に脱脂する事",
"IC供給仕様時"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
">PC<",
"検査表②:安全部品確認",
"検査表②:貼付位置確認",
"検査表LABEL :安全部品確認",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "①の型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付31(後部中央扉小)IC供給仕様",
"WorkItems": [
"■3. にLABEL LABEL を貼付ける",
"■2. LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"記述内容確認",
"型式:LABEL PD0101M1 ②PC010101",
"貼付前に脱脂する事",
"IC供給仕様時"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
">PC<",
"検査表②:安全部品確認",
"検査表②:貼付位置確認",
"検査表LABEL :安全部品確認",
"WWYJ-5300-007"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "⑥⑦⑧の型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-007",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付31(後部中央扉小)IC供給仕様",
"WorkItems": [
"■3. にLABEL LABEL を貼付ける",
"■2. LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける",
"■3. にLABEL LABEL を貼付ける",
"■2. LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表②:安全部品確認",
"検査表LABEL :安全部品確認",
"■安全作業",
"検査表②:安全部品確認",
"検査表LABEL :安全部品確認"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付32(後面中央下)IC供給仕様",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"穴位置寸法が違います",
"貼付前に脱脂する事",
"記述内容確認",
"IC供給仕様時"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
">PC<",
"検査表LABEL :安全部品確認",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付32(後面中央下)IC供給仕様",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"穴位置寸法が違います",
"貼付前に脱脂する事",
"記述内容確認",
"IC供給仕様時"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
">PC<",
"検査表LABEL :安全部品確認",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付33(後面中央)IC供給仕様専用",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認",
"IC供給仕様時"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
">PC<",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付33(後面中央)IC供給仕様専用",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認",
"IC供給仕様時"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
">PC<",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付34(後面下ｶﾊﾞｰ)IC供給仕様専用",
"WorkItems": [
"■2. COVER にLABEL を貼付ける",
"■1. LABEL の型式確認をする"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"型式:PC010201",
"IC供給仕様時"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:安全部品確認",
"検査表①:貼付位置確認",
"KT4",
"図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付",
"WWYJ-5300-007"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "⑥⑦⑧の型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-007",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付34(後面下ｶﾊﾞｰ)IC供給仕様専用",
"WorkItems": [
"■2. COVER にLABEL を貼付ける",
"■1. LABEL の型式確認をする"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"型式:PC010201",
"IC供給仕様時"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:安全部品確認",
"検査表①:貼付位置確認",
"KT4",
"図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付35(後面上中央)TCP供給仕様",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"TCP供給仕様時",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
">PC<",
"検査表LABEL :安全部品確認",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "銘板貼付35(後面上中央)TCP供給仕様",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"TCP供給仕様時",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
">PC<",
"検査表LABEL :安全部品確認",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付36(天井面前側右)",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付36(天井面前側右)",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付37(天井面前側左)",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付37(天井面前側左)",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付38(天井面前側中央)",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付38(天井面前側中央)",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付39(天井面中央側左右)",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認",
"左側",
"右側",
"左右で寸法値違うので注意する",
"穴位置に注意する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付39(天井面中央側左右)",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認",
"左側",
"右側",
"左右で寸法値違うので注意する",
"穴位置に注意する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付40(天井面後側右)",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付40(天井面後側右)",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付41(天井面後側左)",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付41(天井面後側左)",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付42(天井面後側中央)",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
"WWYJ-5300-005"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-005",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付42(天井面後側中央)",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付け①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"(40㎜)",
"(40㎜)",
"(40㎜)"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮置ｶﾊﾞｰR側銘板貼付1",
"WorkItems": [
"2. COVER にLABEL LABEL LABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認",
"正流れ時:下流側逆流れ時:上流側",
"正流れ",
"逆流れ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
">PC<",
"WWYJ-5300-028"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-028",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "仮置ｶﾊﾞｰR側銘板貼付1",
"WorkItems": [
"2. COVER にLABEL LABEL LABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認",
"正流れ時:下流側逆流れ時:上流側",
"正流れ",
"逆流れ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
">PC<",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮置ｶﾊﾞｰR側銘板貼付2",
"WorkItems": [
"■2. COVER にLABEL を貼付ける",
"■1. LABEL の型式確認をする"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"型式:PW0102M1"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
"検査表LABEL :貼付位置確認",
"WWYJ-5300-027"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-027",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮置ｶﾊﾞｰR側銘板貼付2",
"WorkItems": [
"■2. COVER にLABEL を貼付ける",
"■1. LABEL の型式確認をする"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"型式:PW0102M1"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
"検査表LABEL :貼付位置確認",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮置ｶﾊﾞｰR側銘板貼付3",
"WorkItems": [
"■3. FRAME-KIT にLABEL LABEL LABEL を貼付ける",
"■2. LABEL LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"記述内容確認",
"型式:LABEL PD0101M1 ②PC010101 ③PC011701",
"貼付前に脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表②:安全部品確認",
"検査表②:貼付位置確認",
"検査表LABEL :安全部品確認",
">PC<",
">PC<",
"WWYJ-5300-028"
]
} | {
"QualityItem": "①の型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-028",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮置ｶﾊﾞｰR側銘板貼付3",
"WorkItems": [
"■3. FRAME-KIT にLABEL LABEL LABEL を貼付ける",
"■2. LABEL LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"記述内容確認",
"型式:LABEL PD0101M1 ②PC010101 ③PC011701",
"貼付前に脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表②:安全部品確認",
"検査表②:貼付位置確認",
"検査表LABEL :安全部品確認",
">PC<",
">PC<",
"WWYJ-5300-027"
]
} | {
"QualityItem": "⑥⑦⑧の型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-027",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮置ｶﾊﾞｰR側銘板貼付3",
"WorkItems": [
"■3. FRAME-KIT にLABEL LABEL LABEL を貼付ける",
"■2. LABEL LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける",
"■3. FRAME-KIT にLABEL LABEL LABEL を貼付ける",
"■2. LABEL LABEL LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表②:安全部品確認",
"検査表LABEL :安全部品確認",
"■安全作業",
"検査表②:安全部品確認",
"検査表LABEL :安全部品確認"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮置ｶﾊﾞｰR側銘板貼付4",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
">PC<",
"WWYJ-5300-028"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-028",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮置ｶﾊﾞｰR側銘板貼付4",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
">PC<",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮置ｶﾊﾞｰR側銘板貼付5",
"WorkItems": [
"■3. COVER にLABEL を貼付ける",
"■2. LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"記述内容確認",
"型式:PW0101M1",
"貼付前に脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表②:安全部品確認",
"検査表②:貼付位置確認",
"検査表LABEL :安全部品確認",
">PC<",
"WWYJ-5300-028"
]
} | {
"QualityItem": "①の型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-028",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮置ｶﾊﾞｰR側銘板貼付5",
"WorkItems": [
"■3. COVER にLABEL を貼付ける",
"■2. LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"記述内容確認",
"型式:PW0101M1",
"貼付前に脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表②:安全部品確認",
"検査表②:貼付位置確認",
"検査表LABEL :安全部品確認",
">PC<",
"WWYJ-5300-027"
]
} | {
"QualityItem": "⑥の型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-027",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "仮置ｶﾊﾞｰR側銘板貼付5",
"WorkItems": [
"■3. COVER にLABEL を貼付ける",
"■2. LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける",
"■3. COVER にLABEL を貼付ける",
"■2. LABEL の型式確認をする",
"■1. LABEL の型式を確認する",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表②:安全部品確認",
"検査表LABEL :安全部品確認",
">PC<",
"■安全作業",
"検査表②:安全部品確認",
"検査表LABEL :安全部品確認",
">PC<"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮置ｶﾊﾞｰR側銘板貼付6",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認",
"背面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
">PC<",
"WWYJ-5300-028"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-028",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮置ｶﾊﾞｰR側銘板貼付6",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認",
"背面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
">PC<",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮置ｶﾊﾞｰR側銘板貼付7",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認",
"天面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
">PC<",
"WWYJ-5300-028"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-028",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "仮置ｶﾊﾞｰR側銘板貼付7",
"WorkItems": [
"2. COVER にLABEL を貼付ける",
"■1. LABEL の型式を確認する"
],
"WorkPoints": [
"貼付前に脱脂する事",
"記述内容確認",
"天面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表LABEL :安全部品確認",
">PC<",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "非常停止SW組立",
"WorkItems": [
"1. BRACKET にLABEL を貼付",
"■2. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入",
"3. 1.完成品にSWITCH を取付"
],
"WorkPoints": [
"LABEL をBRACKET の中心穴に均等貼付",
"ﾎﾞﾀﾝ側を1.完成品に挿入し､付属のﾅｯﾄで締結",
"型式確認･ｼﾘｱﾙNo記録"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表BRACKET :安全部品確認",
"WWYJ-5300-036"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-036",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "非常停止SW組立",
"WorkItems": [
"1. BRACKET にLABEL を貼付",
"■2. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入",
"3. 1.完成品にSWITCH を取付"
],
"WorkPoints": [
"LABEL をBRACKET の中心穴に均等貼付",
"ﾎﾞﾀﾝ側を1.完成品に挿入し､付属のﾅｯﾄで締結",
"型式確認･ｼﾘｱﾙNo記録"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表BRACKET :安全部品確認",
"WWYJ-5300-036"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-036",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾅｯﾄ締付治具",
"Size": "",
"ToolOther": "FM-2528",
"WorkName": "非常停止SW組立",
"WorkItems": [
"1. BRACKET にLABEL を貼付",
"■2. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入",
"3. 1.完成品にSWITCH を取付"
],
"WorkPoints": [
"LABEL をBRACKET の中心穴に均等貼付",
"ﾎﾞﾀﾝ側を1.完成品に挿入し､付属のﾅｯﾄで締結",
"型式確認･ｼﾘｱﾙNo記録"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表BRACKET :安全部品確認",
"■安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2528",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "非常停止SW組立",
"WorkItems": [
"1. BRACKET にLABEL を貼付",
"■2. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入",
"3. 1.完成品にSWITCH を取付"
],
"WorkPoints": [
"LABEL をBRACKET の中心穴に均等貼付",
"ﾎﾞﾀﾝ側を1.完成品に挿入し､付属のﾅｯﾄで締結",
"型式確認･ｼﾘｱﾙNo記録"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表BRACKET :安全部品確認"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "正しい位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "扉ﾛｯｸｼﾘﾝﾀﾞｰ部組立①",
"WorkItems": [
"1. CYLINDER にSWITCH を取付",
"2. 1完成品にLABEL TERMINAL PROCESS を取付"
],
"WorkPoints": [
"被覆端面とLABEL TERMINAL PROCESS の端面を合わせて取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1B10110-5R"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "扉ﾛｯｸｼﾘﾝﾀﾞｰ部組立②",
"WorkItems": [
"1. にJOINT を取付",
"2. 1完成品にJOINT を取付",
"4. 3.完成品にSUPPORT NUT BOLT WASHER を㉘に入れマスキングテープで止め同梱",
"3. BRACKET に2.完成品をBOLT WASHER で取付"
],
"WorkPoints": [
"BRACKET ﾌﾞﾗｹｯﾄに2.完成品ｼﾘﾝﾀﾞｰを直角平行に取付",
"本体ｶﾊﾞｰﾌﾚｰﾑに固定の為"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"×2",
"×2",
"2.完成品",
"2.完成品"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "扉ｷｬｯﾁ部組立",
"WorkItems": [
"1. BRACKET にCATCH をBOLT WASHER で取付",
"2. 1.完成品にSUPPORT NUT BOLT WASHER を㉗に入れマスキングテープで止め同梱"
],
"WorkPoints": [
"本体ｶﾊﾞｰﾌﾚｰﾑに固定の為"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×2",
"×2"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "扉ｽﾄｯﾊﾟｰ部組立",
"WorkItems": [
"1. PLATE にRUBBER-LEG をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では勝手違いを各1個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "扉ﾏｸﾞﾈｯﾄSW部組立",
"WorkItems": [
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入",
"3. 2.完成品にLABEL TERMINAL PROCESS LABEL TERMINAL PROCESS を取付",
"2. BRACKET にSWITCH をBOLT WASHER WASHER NUT-PLATE で取付"
],
"WorkPoints": [
"型式確認･ｼﾘｱﾙNo記録",
"被覆端面とLABEL TERMINAL PROCESS の端面を合わせて取付"
],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"S308",
"2.完成品",
"検査表BRACKET :安全部品確認",
"PCOVUSA001",
"WWYJ-5300-036"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-036",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "扉ﾏｸﾞﾈｯﾄSW部組立",
"WorkItems": [
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入",
"3. 2.完成品にLABEL TERMINAL PROCESS LABEL TERMINAL PROCESS を取付",
"2. BRACKET にSWITCH をBOLT WASHER WASHER NUT-PLATE で取付"
],
"WorkPoints": [
"型式確認･ｼﾘｱﾙNo記録",
"被覆端面とLABEL TERMINAL PROCESS の端面を合わせて取付"
],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"S308",
"2.完成品",
"検査表BRACKET :安全部品確認",
"PCOVUSA001",
"WWYJ-5300-036"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-036",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾍｸｻﾛﾋﾞｭﾗT-20",
"ToolOther": "1.0N･m",
"WorkName": "扉ﾏｸﾞﾈｯﾄSW部組立",
"WorkItems": [],
"WorkPoints": [
"被覆端面とLABEL TERMINAL PROCESS の端面を合わせて取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"S308",
"2.完成品",
"PCOVUSA001",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "扉ｽﾄｯﾊﾟｰ取付①",
"WorkItems": [
"1. に をBOLT WASHER で取付"
],
"WorkPoints": [
"ﾌﾚｰﾑと平行",
"正面側",
"後面側",
"底面側",
"左面側",
"端面合わせ",
"端面合わせ",
"A矢視図",
"B矢視図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾍｸｻﾛﾋﾞｭﾗT-20",
"ToolOther": "1.0N･m",
"WorkName": "ｾｰﾌﾃｨｰｶﾊﾞｰｽｲｯﾁ取付",
"WorkItems": [
"1. に をBOLT WASHER で取付"
],
"WorkPoints": [
"ﾌﾚｰﾑと平行",
"正面側",
"後面側",
"底面側",
"左面側",
"端面合わせ",
"締付ﾄﾙｸ 1.0N･m"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "非常停止ｽｲｯﾁ取付",
"WorkItems": [
"1. に をBOLT WASHER で取付"
],
"WorkPoints": [
"正面側",
"後面側",
"底面側",
"左面側",
"端面合わせ",
"A矢視図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾋﾝｼﾞ取付",
"WorkItems": [
"1. にHINGE をSCREW で取付"
],
"WorkPoints": [
"正面側",
"後面側",
"底面側",
"左面側",
"ﾌﾚｰﾑに対して平行",
"A矢視図",
"B矢視図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "扉ｽﾄｯﾊﾟｰ取付②",
"WorkItems": [
"1. にSPACER RUBBER-LEG をBOLT で取付"
],
"WorkPoints": [
"正面側",
"後面側",
"底面側",
"左面側",
"A矢視図",
"B矢視図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｷｬｯﾌﾟ取付",
"WorkItems": [
"1. にCAP を取付"
],
"WorkPoints": [
"正面側",
"後面側",
"底面側",
"左面側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "底板取付",
"WorkItems": [
"1. にCOVER COVER COVER をWASHER SCREW で取付"
],
"WorkPoints": [
"底面側",
"左面側",
"正面側",
"後面側"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｽﾀﾝﾄﾞ取付①",
"WorkItems": [
"1. にSUPPORT NUT を取付"
],
"WorkPoints": [
"底面側",
"左面側",
"正面側",
"後面側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×3",
"×3",
"101㎜",
"101㎜",
"101㎜",
"101㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ｽﾀﾝﾄﾞ取付②",
"WorkItems": [
"1. に をWASHER BOLT で取付"
],
"WorkPoints": [
"底面側",
"左面側",
"正面側",
"後面側"
],
"Tolks": [
"締付ﾄﾙｸ 11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×3",
"×3"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "払出",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. HINGE ~GASKET BOLT WASHER をﾄﾞｯｷﾝｸﾞ工程へ払い出し"
]
} | {
"QualityItem": "払出確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り払い出されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立横",
"WorkItems": [
"1. FRAME にSUPPORT NUT NUT NUT CABLE-SUPPORT を取付",
"2. 1.完成品にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立縦",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT を取付",
"2. 1.完成品にBRACKET をBOLT ･WASHER で取付"
],
"WorkPoints": [
"上面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立",
"WorkItems": [
"1. に をBOLT WASHER で取付",
"2. ㉘にBOLT WASHER (各8個)を入れマスキングテープで止め同梱"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "HEPA組立",
"WorkItems": [
"3. BOLT WASHER WASHER (残り2個)を㉙に入れマスキングテープで止め同梱",
"2. BLOWER の取付ﾌﾞﾗｹｯﾄを1.完成品と交換し取り外したﾎﾞﾙﾄで固定",
"1. BRACKET のﾌﾞﾗｹｯﾄ2個にTAPE ｶﾌﾟﾄﾝﾃｰﾌﾟを貼付け"
],
"WorkPoints": [
"4ヶ所",
"交換したﾌﾞﾗｹｯﾄは廃棄",
"交換前と反対で下面を合わせて固定する",
"BRACKET の曲げが下側",
"下面を合わせる",
"この作業は4個の内2個のみ実施"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備①",
"WorkItems": [
"1. GROMMET に切り込みを入れる",
"2. COVER に1.完成品･GROMMET を取付"
],
"WorkPoints": [
"切り込み"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ上面ｶﾊﾞｰ準備②",
"WorkItems": [
"1. COVER にGROMMET を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立①",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT ･NUT ･CAP ･CABLE-SUPPORT を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"正面",
"右面",
"裏面",
"左面",
"上面",
"正面",
"上面",
"右面",
"裏面",
"正面",
"左面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M6",
"M5",
"M4",
"×3",
"×3",
"×3",
"×4",
"×9"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立②",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT ･NUT ･CAP ･CABLE-SUPPORT を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"正面",
"右面",
"裏面",
"左面",
"上面",
"正面",
"上面",
"右面",
"裏面",
"正面",
"左面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M6",
"M5",
"M4",
"×3",
"×3",
"×3",
"×4",
"×9"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立③",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT ･NUT を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"正面",
"裏面",
"左面",
"上面",
"左面",
"上面",
"裏面",
"正面",
"下面",
"正面",
"下面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M6",
"M5",
"M4"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立④",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT ･NUT ･CABLE-SUPPORT を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"上面",
"右面",
"正面",
"左面",
"正面",
"正面",
"右面",
"裏面",
"左面",
"上面",
"裏面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M6",
"M5",
"M4"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立⑤",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT ･NUT ･CABLE-SUPPORT を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"右面",
"正面",
"左面",
"正面",
"正面",
"右面",
"裏面",
"左面",
"上面",
"裏面",
"上面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M6",
"M5",
"M4"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立⑥",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT ･NUT を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"左面",
"上面",
"正面",
"下面",
"正面",
"裏面",
"正面",
"裏面",
"左面",
"上面",
"下面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M6",
"M5",
"M4"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑ組立⑦",
"WorkItems": [
"1. ･ ･ をBRACKET ･WASHER ･BOLT で取付"
],
"WorkPoints": [
"正面･上面･左面の向きに注意",
"正面",
"上面",
"左面"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑ組立⑧",
"WorkItems": [
"1. ･ ･ をBRACKET ･WASHER ･BOLT で取付"
],
"WorkPoints": [
"正面･上面･左面の向きに注意",
"正面",
"上面",
"左面"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.