input stringclasses 1 value | instruction stringlengths 222 1.92k | output stringlengths 193 312 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "1.5N･m",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立①",
"WorkItems": [
"1. AIR-CHUCK にJOINT を取付",
"2. 1完成品のｵｰﾄSWの止めねじをSCREW と交換 ※2か所",
"3. 2完成品に㉚のエアー供給ユニットを接続し、エアーを供給",
"4. ｼﾘﾝﾀﾞｰ【開】状態のSWITCH-KIT ｵｰﾄSW調整"
],
"WorkPoints": [
"交換した止めねじは廃棄する",
"ｵｰﾄSWの合わせ方参照",
"継手(開/閉)両方に接続し､ﾊﾞﾙﾌﾞにて切り替え動作実施 ※ｴｱｰ供給圧 0.5Mpa"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.27㎜",
"ToolOther": "10cN･m",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立①",
"WorkItems": [
"5. ｼﾘﾝﾀﾞｰ【閉】状態のSWITCH-KIT ｵｰﾄSW調整"
],
"WorkPoints": [
"ﾏｰｷﾝｸﾞ中央に取付",
"㉜8㎜ブロックゲージを挟んでから閉状態にする",
"ｵｰﾄSWの合わせ方参照"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m",
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｵｰﾄSW 【B106】",
"ｵｰﾄSW 【B104】"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｵｰﾄSW位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4292",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立①",
"WorkItems": [
"5. ｼﾘﾝﾀﾞｰ【閉】状態のSWITCH-KIT ｵｰﾄSW調整"
],
"WorkPoints": [
"ﾏｰｷﾝｸﾞ中央に取付",
"ﾏｰｷﾝｸﾞ中央に取付",
"㉜8㎜ブロックゲージを挟んでから閉状態にする",
"ｵｰﾄSWの合わせ方参照"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｵｰﾄSW 【B106】",
"ｵｰﾄSW 【B106】",
"ｵｰﾄSW 【B104】"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4292",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ(共通)",
"Size": "",
"ToolOther": "FM-3418",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立①",
"WorkItems": [
"5. ｼﾘﾝﾀﾞｰ【閉】状態のSWITCH-KIT ｵｰﾄSW調整"
],
"WorkPoints": [
"ﾏｰｷﾝｸﾞ中央に取付",
"㉜8㎜ブロックゲージを挟んでから閉状態にする",
"ｵｰﾄSWの合わせ方参照"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｵｰﾄSW 【B106】",
"ｵｰﾄSW 【B104】"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-3418",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "開閉限位置でONする事",
"Method": "PHﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ(2､8､11)",
"Size": "",
"ToolOther": "FM-6114",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立①",
"WorkItems": [
"5. ｼﾘﾝﾀﾞｰ【閉】状態のSWITCH-KIT ｵｰﾄSW調整"
],
"WorkPoints": [
"ﾏｰｷﾝｸﾞ中央に取付",
"㉜8㎜ブロックゲージを挟んでから閉状態にする",
"ｵｰﾄSWの合わせ方参照"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｵｰﾄSW 【B106】",
"ｵｰﾄSW 【B104】"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "FM-6114",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "8㎜を挟み取付の事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立②",
"WorkItems": [
"1. 配線の指定寸法にﾏｰｷﾝｸﾞ実施"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"220mm",
"【B106P】",
"130mm",
"【B104P】",
"160mm",
"80mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法±1.0㎜以内",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "63cN･m",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立③",
"WorkItems": [
"4. 2完成品BRACKET BRACKET の取付調整"
],
"WorkPoints": [
"2㎜ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"8㎜ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"以下の状態でBRACKET BRACKET を調整",
"シリンダーに㉘8㎜ブロックゲージを挟んだ状態で、エアーを供給【0.5Mpa】",
"BRACKET BRACKET で㉘11㎜ブロックゲージを挟んだ状態",
"BRACKET BRACKET とシリンダーの間に㉘2㎜ブロックゲージを挟んだ状態",
"【注意】 BRACKET BRACKET は取付穴左右ｾﾝﾀｰ狙いで取付"
],
"Tolks": [
"締付ﾄﾙｸ 63cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "63cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ(2､8､11)",
"Size": "",
"ToolOther": "FM-6114",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立③",
"WorkItems": [
"4. 2完成品BRACKET BRACKET の取付調整"
],
"WorkPoints": [
"2㎜ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"8㎜ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"以下の状態でBRACKET BRACKET を調整",
"シリンダーに㉘8㎜ブロックゲージを挟んだ状態で、エアーを供給【0.5Mpa】",
"BRACKET BRACKET で㉘11㎜ブロックゲージを挟んだ状態",
"BRACKET BRACKET とシリンダーの間に㉘2㎜ブロックゲージを挟んだ状態",
"【注意】 BRACKET BRACKET は取付穴左右ｾﾝﾀｰ狙いで取付"
],
"Tolks": [
"締付ﾄﾙｸ 63cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6114",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各2・8・11㎜を挟み取付の事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｵｰﾄSW位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4292",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立③",
"WorkItems": [
"1. BRACKET BRACKET のﾊﾞﾘ､打痕を確認",
"2. にBRACKET BRACKET をBOLT にて仮取付",
"3. ㉙エアー供給ユニットを接続",
"4. 2完成品BRACKET BRACKET の取付調整"
],
"WorkPoints": [
"青色矢印部分に接続 ※ｴｱｰはまだ供給しない",
"2㎜ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"8㎜ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"以下の状態でBRACKET BRACKET を調整",
"シリンダーに㉘8㎜ブロックゲージを挟んだ状態で、エアーを供給【0.5Mpa】",
"BRACKET BRACKET で㉘11㎜ブロックゲージを挟んだ状態",
"BRACKET BRACKET とシリンダーの間に㉘2㎜ブロックゲージを挟んだ状態",
"【注意】 BRACKET BRACKET は取付穴左右ｾﾝﾀｰ狙いで取付"
],
"Tolks": [
"締付ﾄﾙｸ 63cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4292",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立④",
"WorkItems": [
"1. にCABLE-SUPPORT BOLT を2か所取付",
"2. 1完成品の配線を結束"
],
"WorkPoints": [
"緑丸部は1本で結束の事",
"黄丸部のﾏｰｷﾝｸﾞが揃っていることを確認後､結束",
"ｲﾝｼｭﾛｯｸから90mmのﾏｰｷﾝｸﾞが揃っている事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"【B106P】 180mm",
"【B104P】 195mm",
"90mm",
"ｵｰﾄSW配線ﾏｰｷﾝｸﾞを合わす (2本)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立④",
"WorkItems": [
"1. にCABLE-SUPPORT BOLT を2か所取付",
"2. 1完成品の配線を結束"
],
"WorkPoints": [
"緑丸部は1本で結束の事",
"黄丸部のﾏｰｷﾝｸﾞが揃っていることを確認後､結束",
"ｲﾝｼｭﾛｯｸから90mmのﾏｰｷﾝｸﾞが揃っている事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"【B106P】 180mm",
"【B104P】 195mm",
"90mm",
"ｵｰﾄSW配線ﾏｰｷﾝｸﾞを合わす (2本)"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法±1.0㎜以内",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "1.5N･m",
"WorkName": "ﾌﾟﾚｰﾄ部ｼﾘﾝﾀﾞ組立①",
"WorkItems": [],
"WorkPoints": [
"仮止め:SD-A040344-038にて調整"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表AIR-SLIDE :ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ調整 (D,E)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ部ｼﾘﾝﾀﾞ組立①",
"WorkItems": [
"1. AIR-SLIDE のｵｰﾄSWのﾄﾒﾈｼﾞをSCREW と交換する ※2か所",
"2. おおむね略図の位置にｵｰﾄSWを仮取付",
"3. 2完成品にSPEED-CONTROLLER を2か所取付",
"4. SPEED-CONTROLLER ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ調整"
],
"WorkPoints": [
"B102P",
"B103P",
"仮止め:SD-A040344-038にて調整"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表AIR-SLIDE :ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ調整 (D,E)"
],
"WorkTypes": [],
"Words": [
"全閉状態から1.5回転開けてﾛｯｸする",
"全閉状態から1回転開けてﾛｯｸする",
"WEPJ-G002-C040"
]
} | {
"QualityItem": "ｽﾋﾟｺﾝ調整",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り調整できている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "ﾌﾟﾚｰﾄ部ｼﾘﾝﾀﾞ組立②",
"WorkItems": [
"1. にBRACKET をBOLT にて取付"
],
"WorkPoints": [
"取付寸法=略図参照",
" とBRACKET の端面を揃える"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｴｱｽﾗｲﾄﾞとﾌﾞﾗｹｯﾄの端面を揃える"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱｽﾗｲﾄﾞ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5980",
"WorkName": "ﾌﾟﾚｰﾄ部ｼﾘﾝﾀﾞ組立②",
"WorkItems": [
"1. にBRACKET をBOLT にて取付"
],
"WorkPoints": [
"取付寸法=略図参照",
" とBRACKET の端面を揃える"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｴｱｽﾗｲﾄﾞとﾌﾞﾗｹｯﾄの端面を揃える"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5980",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ部ｼﾘﾝﾀﾞ組立②",
"WorkItems": [
"2. 取付寸法確認"
],
"WorkPoints": [
"1完成品の取付位置寸法を確認",
"取付位置寸法:37.1㎜±0.1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"37.1mm±0.1mm",
"治具使用例"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "指定寸法±0.1㎜以内",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｯｸﾀｲﾄ",
"Size": "",
"ToolOther": "243",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部ﾌﾟﾚｰﾄ組立",
"WorkItems": [
"1. PLATE にﾊﾞﾘ､打痕が無いことを確認する",
"▲2. SCREW に㉘塗布後、PLATE に取付"
],
"WorkPoints": [
"4箇所"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:各1",
"▲特殊作業"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部ﾌﾟﾚｰﾄ組立",
"WorkItems": [
"3. SCREW の出代を調整する"
],
"WorkPoints": [
"SCREW をねじ込み､板裏出代1mm±0.1mmに取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1mm±0.1mm",
"▲特殊作業"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立①",
"WorkItems": [
"1. に をBOLT にて取付",
"2. 隙間､及び干渉確認 ※略図青線部分"
],
"WorkPoints": [
"Sﾋﾟﾝ(3点)との間に隙間のない様に取付",
"Sﾋﾟﾝ当付け面の隙間を確認 ※青線部分"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立①",
"WorkItems": [],
"WorkPoints": [
"必要部分のみ描いています",
"【目視確認】 ﾌﾞﾗｹｯﾄU溝部分とﾎﾞﾙﾄの干渉が無い事",
"各隙間 0.03mmが通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立②",
"WorkItems": [
"1. に をBOLT にて取付"
],
"WorkPoints": [
" 上辺に隙間のない様に取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立②",
"WorkItems": [
"2. 取付確認 ※略図青線部分"
],
"WorkPoints": [
"当付け面の隙間を確認 ※青線部分",
"各隙間 0.03㎜が通ら無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "63cN･m",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立③",
"WorkItems": [
"1. に を付属ﾎﾞﾙﾄにて取付"
],
"WorkPoints": [
" の取付穴はｼﾘﾝﾀﾞｰを開状態にすると現れる ※黄色矢印方向",
" は の基準ﾋﾟﾝに嵌合させて取付",
"付属ﾎﾞﾙﾄ M3×20 2本"
],
"Tolks": [
"締付ﾄﾙｸ 63cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "63cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立④",
"WorkItems": [
"1. に をBOLT にて仮取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"仮止め:SD-A046151-106にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｵｰﾄSW位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4292",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立⑤",
"WorkItems": [
"1. のｵｰﾄSW調整"
],
"WorkPoints": [
"点灯した位置でﾏｰｷﾝｸﾞ",
"消灯した位置でﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ中央に取付",
"ｵｰﾄSW取付の合わせ方",
"戻り限調整",
"行き限調整",
"㉖エアー供給ユニットより、青色矢印側にエアを供給 【0.5Mpa】",
"青丸部分のSWを調整",
"㉖エアー供給ユニットより、黄色矢印側にエアを供給 【0.5Mpa】",
"黄丸部分のSWを調整"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4292",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ(共通)",
"Size": "",
"ToolOther": "FM-3418",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立⑤",
"WorkItems": [
"1. のｵｰﾄSW調整"
],
"WorkPoints": [
"点灯した位置でﾏｰｷﾝｸﾞ",
"消灯した位置でﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ中央に取付",
"ｵｰﾄSW取付の合わせ方",
"戻り限調整",
"行き限調整",
"㉖エアー供給ユニットより、青色矢印側にエアを供給 【0.5Mpa】",
"青丸部分のSWを調整",
"㉖エアー供給ユニットより、黄色矢印側にエアを供給 【0.5Mpa】",
"黄丸部分のSWを調整"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-3418",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "開閉限位置でONする事",
"Method": "PHﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.27㎜",
"ToolOther": "10cN･m",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立⑤",
"WorkItems": [
"1. のｵｰﾄSW調整"
],
"WorkPoints": [
"点灯した位置でﾏｰｷﾝｸﾞ",
"消灯した位置でﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ中央に取付",
"ｵｰﾄSW取付の合わせ方",
"戻り限調整",
"行き限調整",
"㉖エアー供給ユニットより、青色矢印側にエアを供給 【0.5Mpa】",
"青丸部分のSWを調整",
"㉖エアー供給ユニットより、黄色矢印側にエアを供給 【0.5Mpa】",
"黄丸部分のSWを調整"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立⑥",
"WorkItems": [
"1. のｵｰﾄSW配線にﾏｰｷﾝｸﾞ実施"
],
"WorkPoints": [
"指定寸法にてﾏｰｷﾝｸﾞ実施 ※略図参照"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"90mm",
"100mm",
"B103P",
"B102P"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法±1.0㎜以内",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｯｸ(A013)ﾋﾟﾝ圧入",
"WorkItems": [
"1. BLOCK にPIN (4個)を打ち込む"
],
"WorkPoints": [
"座ぐり面を下にする",
"圧入方向に注意(割りの向き)",
"圧入方向に注意(割りの向き)",
"圧入時BLOCK の方向に注意",
"出代5mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5㎜"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法±0.5㎜以内",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "中継ﾎﾞｰﾄﾞ用ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. BRACKET にCABLE-SUPPORT をBOLT で取付",
"2. 1完成品にBUSH を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5㎜BOX",
"ToolOther": "120cN･m",
"WorkName": "中継ﾎﾞｰﾄﾞ用ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"3. 2完成品にSPACER WASHER を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 110cN･m",
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "中継ﾎﾞｰﾄﾞ用ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. BRACKET にCABLE-SUPPORT をBOLT で取付",
"2. 1完成品にBUSH を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "中継ﾎﾞｰﾄﾞ部組立",
"WorkItems": [
"■1. HOT SWAP RELAY BOARD の検査成績書の添付を確認し､検査日､入荷日､判定を記入",
"■★2. HOT SWAP RELAY BOARD の型番を確認し､ｼﾘｱﾙ№を検査表に記入",
"★3. にHOT SWAP RELAY BOARD をBOLT WASHER (各4個)で取付"
],
"WorkPoints": [
"ｼﾘｱﾙﾗﾍﾞﾙの位置",
"HOT SWAP RELAY BOARD の取付方向は下図のｼﾘｱﾙﾗﾍﾞﾙの位置の通り取付こと"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表 :安全部品 検査",
"検査表 :安全部品 検査"
],
"WorkTypes": [],
"Words": [
"WEPJ-G002-C040"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式を確認",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "中継ﾎﾞｰﾄﾞ部組立",
"WorkItems": [
"■1. HOT SWAP RELAY BOARD の検査成績書の添付を確認し､検査日､入荷日､判定を記入",
"■★2. HOT SWAP RELAY BOARD の型番を確認し､ｼﾘｱﾙ№を検査表に記入",
"★3. にHOT SWAP RELAY BOARD をBOLT WASHER (各4個)で取付"
],
"WorkPoints": [
"ｼﾘｱﾙﾗﾍﾞﾙの位置",
"HOT SWAP RELAY BOARD の取付方向は下図のｼﾘｱﾙﾗﾍﾞﾙの位置の通り取付こと"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表 :安全部品 検査",
"検査表 :安全部品 検査"
],
"WorkTypes": [],
"Words": [
"WEPJ-G002-C040"
]
} | {
"QualityItem": "検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "検査表の有無を確認する事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "80cN･m",
"WorkName": "中継ﾎﾞｰﾄﾞ部組立",
"WorkItems": [
"■1. HOT SWAP RELAY BOARD の検査成績書の添付を確認し､検査日､入荷日､判定を記入",
"■★2. HOT SWAP RELAY BOARD の型番を確認し､ｼﾘｱﾙ№を検査表に記入",
"★3. にHOT SWAP RELAY BOARD をBOLT WASHER (各4個)で取付"
],
"WorkPoints": [
"ｼﾘｱﾙﾗﾍﾞﾙの位置",
"HOT SWAP RELAY BOARD の取付方向は下図のｼﾘｱﾙﾗﾍﾞﾙの位置の通り取付こと"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :安全部品 検査",
"検査表 :安全部品 検査",
"■安全作業",
"★静電対策作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "1.5N･m",
"WorkName": "ﾕﾆｯﾄﾛｯｸ部ｼﾘﾝﾀﾞ組立",
"WorkItems": [
"1. CYLINDER にJOINT (2個)を取付",
"2. CYLINDER のｵｰﾄｽｲｯﾁのすりわり付き止めねじとSCREW を交換し行き限でｾﾝｻｰ位置調整すること"
],
"WorkPoints": [
"ｵｰﾄSW位置調整は､治具を接続しｼﾘﾝﾀﾞｰｼｬﾌﾄが行き限の状態でSWのLEDが点灯している事",
"CYLINDER の付属ﾎﾞﾙﾄはSD-A046151-043で使用"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.27㎜",
"ToolOther": "10cN･m",
"WorkName": "ﾕﾆｯﾄﾛｯｸ部ｼﾘﾝﾀﾞ組立",
"WorkItems": [],
"WorkPoints": [
"点灯した位置でﾏｰｷﾝｸﾞ",
"消灯した位置でﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ中央に取付",
"ｵｰﾄSW取付の合わせ方"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｵｰﾄSW位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4292",
"WorkName": "ﾕﾆｯﾄﾛｯｸ部ｼﾘﾝﾀﾞ組立",
"WorkItems": [],
"WorkPoints": [
"点灯した位置でﾏｰｷﾝｸﾞ",
"消灯した位置でﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ中央に取付",
"ｵｰﾄSW取付の合わせ方"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4292",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾝﾄﾞﾙ部組立",
"WorkItems": [
"1. GRIP にLEVER を素手でねじ込む"
],
"WorkPoints": [
"LEVER の短いほうをGRIP に取付",
"ﾈｼﾞ緩みの無いこと"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表GRIP :ﾒｶﾆｶﾙﾁｪｯｸ"
],
"WorkTypes": [],
"Words": [
"WEPJ-G002-C040"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾀｲﾏｳﾝﾄ取付",
"WorkItems": [],
"WorkPoints": [
"15箇所取付",
"規格値:手で触れる部分に著しいﾊﾞﾘ･打痕無い事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表BRACKET :ﾒｶﾆｶﾙﾁｪｯｸ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾀｲﾏｳﾝﾄ取付",
"WorkItems": [],
"WorkPoints": [
"15箇所取付",
"規格値:手で触れる部分に著しいﾊﾞﾘ･打痕無い事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表BRACKET :ﾒｶﾆｶﾙﾁｪｯｸ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾀｲﾏｳﾝﾄ取付",
"WorkItems": [],
"WorkPoints": [
"15箇所取付",
"規格値:手で触れる部分に著しいﾊﾞﾘ･打痕無い事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表BRACKET :ﾒｶﾆｶﾙﾁｪｯｸ"
],
"WorkTypes": [],
"Words": [
"WEPJ-G002-C040"
]
} | {
"QualityItem": "ﾊﾞﾘ･打痕確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕､傷などが無い事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾀｲﾏｳﾝﾄ取付",
"WorkItems": [],
"WorkPoints": [
"15箇所取付",
"規格値:手で触れる部分に著しいﾊﾞﾘ･打痕無い事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表BRACKET :ﾒｶﾆｶﾙﾁｪｯｸ"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5㎜BOX",
"ToolOther": "120cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄｽﾍﾟｰｻｰ取付",
"WorkItems": [
"1. SPACER WASHER を に取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾌﾞﾛｯｸ取付",
"WorkItems": [
"2. に1完成品をBOLT ･COLLAR BOLT で取付",
"1. 下図のようにBLOCK ､ にPLATE (2個)とCOLLAR (4個)をｾｯﾄ"
],
"WorkPoints": [
"･PLATE の凸の向きをBLOCK 側にすること",
"下図BLOCK の左側ﾋﾟﾝにPLATE の青丸部を挿入"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. BRACKET にBRACKET をBOLT WASHER で取付",
"2. 1.完成品にBUSH を貼付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"この作業では1個のみ",
"15㎜"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"3. に1.完成品と2.完成品をBOLT WASHER で取付"
],
"WorkPoints": [
"㉙ﾊﾝﾄﾞﾙ取付位置調整治具にて取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊﾝﾄﾞﾙ取付位置調整治具",
"Size": "",
"ToolOther": "FM-4272",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"3. に1.完成品と2.完成品をBOLT WASHER で取付"
],
"WorkPoints": [
"㉙ﾊﾝﾄﾞﾙ取付位置調整治具にて取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4272",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. BRACKET にBRACKET をBOLT WASHER で取付",
"2. 1.完成品にBUSH を貼付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"この作業では1個のみ",
"15㎜"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法±1.0㎜以内",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄｼﾘﾝﾀﾞ取付",
"WorkItems": [
"1. を に 付属のﾎﾞﾙﾄとWASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"付属ﾎﾞﾙﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾊﾝﾄﾞﾙ取付",
"WorkItems": [
"1. に をWASHER NUT NUT で取付"
],
"WorkPoints": [
"ﾈｼﾞ緩みの無いこと"
],
"Tolks": [
"締付ﾄﾙｸ 5.5N･m",
"締付ﾄﾙｸ 6N･m"
],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表 :ﾒｶﾆｶﾙﾁｪｯｸ"
],
"WorkTypes": [],
"Words": [
"WEPJ-G002-C040"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "緩み無い事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "5.5N･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾊﾝﾄﾞﾙ取付",
"WorkItems": [
"1. に をWASHER NUT NUT で取付"
],
"WorkPoints": [
"ﾈｼﾞ緩みの無いこと"
],
"Tolks": [
"締付ﾄﾙｸ 5.5N･m",
"締付ﾄﾙｸ 6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾒｶﾆｶﾙﾁｪｯｸ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "6N･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾊﾝﾄﾞﾙ取付",
"WorkItems": [
"1. に をWASHER NUT NUT で取付"
],
"WorkPoints": [
"ﾈｼﾞ緩みの無いこと"
],
"Tolks": [
"締付ﾄﾙｸ 5.5N･m",
"締付ﾄﾙｸ 6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾒｶﾆｶﾙﾁｪｯｸ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄ制御ﾎﾞｰﾄﾞ取付",
"WorkItems": [
"★3. にHEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) をSPACER BOLT WASHER WASHER で取付",
"■1. HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の検査成績書の添付を確認し､検査日､入荷日､判定を検査表に記載",
"■★2. HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の品番､型番を確認し､ｼﾘｱﾙ№を検査表に記入"
],
"WorkPoints": [
"HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の基板の取付方向に注意する",
"このｺﾈｸﾀｰをﾊﾝﾄﾞﾙ側に向ける",
"このｺﾈｸﾀｰを前側に向ける"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表SPACER :安全部品 検査",
"検査表SPACER :安全部品 検査"
],
"WorkTypes": [],
"Words": [
"WEPJ-G002-C040"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式を確認",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄ制御ﾎﾞｰﾄﾞ取付",
"WorkItems": [
"★3. にHEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) をSPACER BOLT WASHER WASHER で取付",
"■1. HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の検査成績書の添付を確認し､検査日､入荷日､判定を検査表に記載",
"■★2. HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の品番､型番を確認し､ｼﾘｱﾙ№を検査表に記入"
],
"WorkPoints": [
"HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の基板の取付方向に注意する",
"このｺﾈｸﾀｰをﾊﾝﾄﾞﾙ側に向ける",
"このｺﾈｸﾀｰを前側に向ける"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表SPACER :安全部品 検査",
"検査表SPACER :安全部品 検査"
],
"WorkTypes": [],
"Words": [
"WEPJ-G002-C040"
]
} | {
"QualityItem": "検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "検査表の有無を確認する事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5㎜BOX",
"ToolOther": "95cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄ制御ﾎﾞｰﾄﾞ取付",
"WorkItems": [
"★3. にHEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) をSPACER BOLT WASHER WASHER で取付",
"■1. HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の検査成績書の添付を確認し､検査日､入荷日､判定を検査表に記載",
"■★2. HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の品番､型番を確認し､ｼﾘｱﾙ№を検査表に記入"
],
"WorkPoints": [
"HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の基板の取付方向に注意する",
"このｺﾈｸﾀｰをﾊﾝﾄﾞﾙ側に向ける",
"このｺﾈｸﾀｰを前側に向ける"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表SPACER :安全部品 検査",
"検査表SPACER :安全部品 検査",
"■安全作業",
"★静電対策作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "80cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄ制御ﾎﾞｰﾄﾞ取付",
"WorkItems": [
"★3. にHEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) をSPACER BOLT WASHER WASHER で取付",
"■1. HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の検査成績書の添付を確認し､検査日､入荷日､判定を検査表に記載",
"■★2. HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の品番､型番を確認し､ｼﾘｱﾙ№を検査表に記入"
],
"WorkPoints": [
"HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の基板の取付方向に注意する",
"このｺﾈｸﾀｰをﾊﾝﾄﾞﾙ側に向ける",
"このｺﾈｸﾀｰを前側に向ける"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表SPACER :安全部品 検査",
"検査表SPACER :安全部品 検査",
"■安全作業",
"★静電対策作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "80cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄ中継ﾎﾞｰﾄﾞ部取付",
"WorkItems": [
"★1. に をBOLT WASHER で取付"
],
"WorkPoints": [
"ｹｰﾌﾞﾙｻﾎﾟｰﾄの位置",
"取付方向に注意"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"★静電対策作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾛｰﾄﾞｾﾙ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾛｰﾄﾞｾﾙ取付",
"WorkItems": [
"1. に をBOLT にて取付",
"2. 隙間確認"
],
"WorkPoints": [
"ﾋﾟﾝと段差に当てつけて取付",
"Sﾋﾟﾝ当付け面の隙間を確認 ※青線部分",
"段差の隙間を確認 ※黄色矢印部分が段差隙間部分",
"各隙間 0.03mmのｼｯｸﾈｽｹﾞｰｼﾞが通らないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "清掃部取付",
"WorkItems": [
"1. に をBOLT にて取付",
"2. 隙間確認"
],
"WorkPoints": [
"Sﾋﾟﾝ当付け面の隙間を確認 ※青線部分",
"ﾋﾟﾝに当付けて取付",
"各隙間 0.03mmのｼｯｸﾈｽｹﾞｰｼﾞが通らないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "清掃部取付",
"WorkItems": [
"1. に をBOLT にて取付",
"2. 隙間確認"
],
"WorkPoints": [
"Sﾋﾟﾝ当付け面の隙間を確認 ※青線部分",
"ﾋﾟﾝに当付けて取付",
"各隙間 0.03mmのｼｯｸﾈｽｹﾞｰｼﾞが通らないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.27㎜",
"ToolOther": "10cN･m",
"WorkName": "清掃部ｵｰﾄSW調整",
"WorkItems": [
"1. のｵｰﾄSW調整",
"2. 調整後､継手を傾ける",
"3. ｵｰﾄSW配線にﾏｰｷﾝｸﾞ実施"
],
"WorkPoints": [
"㉘エアー供給ユニットより、戻り側接手にエアーを供給 ※青色矢印",
"ｴｱｰ供給圧【0.5Mpa】",
"ｵｰﾄSWより60mmにﾏｰｷﾝｸﾞ実施"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｵｰﾄSW位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4292",
"WorkName": "清掃部ｵｰﾄSW調整",
"WorkItems": [
"1. のｵｰﾄSW調整",
"2. 調整後､継手を傾ける",
"3. ｵｰﾄSW配線にﾏｰｷﾝｸﾞ実施"
],
"WorkPoints": [
"㉘エアー供給ユニットより、戻り側接手にエアーを供給 ※青色矢印",
"ｴｱｰ供給圧【0.5Mpa】",
"ｵｰﾄSWより60mmにﾏｰｷﾝｸﾞ実施"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4292",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ(共通)",
"Size": "",
"ToolOther": "FM-3418",
"WorkName": "清掃部ｵｰﾄSW調整",
"WorkItems": [
"1. のｵｰﾄSW調整",
"2. 調整後､継手を傾ける",
"3. ｵｰﾄSW配線にﾏｰｷﾝｸﾞ実施"
],
"WorkPoints": [
"㉘エアー供給ユニットより、戻り側接手にエアーを供給 ※青色矢印",
"ｴｱｰ供給圧【0.5Mpa】",
"ｵｰﾄSWより60mmにﾏｰｷﾝｸﾞ実施"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3418",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "ｰ",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "清掃部ｵｰﾄSW調整",
"WorkItems": [
"1. のｵｰﾄSW調整",
"2. 調整後､継手を傾ける",
"3. ｵｰﾄSW配線にﾏｰｷﾝｸﾞ実施"
],
"WorkPoints": [
"㉘エアー供給ユニットより、戻り側接手にエアーを供給 ※青色矢印",
"ｴｱｰ供給圧【0.5Mpa】",
"ｵｰﾄSWより60mmにﾏｰｷﾝｸﾞ実施"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "清掃部ｴｱﾁｭｰﾌﾞ接続",
"WorkItems": [
"2. ｴｱﾁｭｰﾌﾞにﾏｰｷﾝｸﾞ",
"3. TUBE ﾁｭｰﾌﾞにAﾎﾟｰﾄ識別ﾏｰｷﾝｸﾞ",
"1. にTUBE TUBE ｴｱﾁｭｰﾌﾞ接続"
],
"WorkPoints": [
"【長さ175mm】",
"【長さ145mm】",
"清掃部上昇 Aﾎﾟｰﾄ【行き】 TUBE 145mm",
"清掃部下降 Bﾎﾟｰﾄ【戻り】 TUBE 175mm",
"TUBE 145mm 先端より70mmにﾏｰｷﾝｸﾞ",
"TUBE 175mm 先端より80mmにﾏｰｷﾝｸﾞ",
"70mmの中央付近にﾏｰｷﾝｸﾞ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"70mm",
"80mm",
"Aﾎﾟｰﾄ清掃部上昇"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "清掃部配線配管",
"WorkItems": [
"2. 配線ﾏｰｷﾝｸﾞ位置で結束",
"3. ｴｱﾁｭｰﾌﾞどおしを結束",
"1. のｵｰﾄSW線引き回し ※略図青線部分"
],
"WorkPoints": [
"ｴｱﾁｭｰﾌﾞの下を通し､配線ﾏｰｷﾝｸﾞとﾀｲﾏｳﾝﾄを合わす",
"ｴｱﾁｭｰﾌﾞを省いて描いています",
"動作部分に干渉しない為の結束",
"配線を省いて描いています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"配線ﾏｰｷﾝｸﾞ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "20cN･m",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部取付",
"WorkItems": [
"2. ﾌﾟﾚｰﾄ部ｼﾘﾝﾀﾞｰを規正ﾋﾟﾝに当てつけて締結",
"1. に をBOLT WASHER にて仮締結"
],
"WorkPoints": [
"目視にて隙間確認",
"規正ﾋﾟﾝの指示の為､ﾛｰﾄﾞｾﾙの無い図としています",
"ﾎﾞﾙﾄ4本を均等に締付"
],
"Tolks": [
"締付ﾄﾙｸ 20cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "100cN･m",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部取付",
"WorkItems": [
"2. ﾌﾟﾚｰﾄ部ｼﾘﾝﾀﾞｰを規正ﾋﾟﾝに当てつけて締結",
"1. に をBOLT WASHER にて仮締結"
],
"WorkPoints": [
"目視にて隙間確認",
"規正ﾋﾟﾝの指示の為､ﾛｰﾄﾞｾﾙの無い図としています",
"ﾎﾞﾙﾄ4本を均等に締付"
],
"Tolks": [
"締付ﾄﾙｸ 20cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "清掃部ｴｱﾁｭｰﾌﾞ結束",
"WorkItems": [
"1. の清掃部ｼﾘﾝﾀﾞｰ用ｴｱﾁｭｰﾌﾞの結束"
],
"WorkPoints": [
"ﾏｰｷﾝｸﾞ箇所で結束"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ(100mm)",
"結束位置ﾏｰｷﾝｸﾞ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線結束",
"WorkItems": [
"1. の各配線の結束 (4か所)"
],
"WorkPoints": [
"ｾﾝｻｰ線のﾏｰｷﾝｸﾞとﾀｲﾏｳﾝﾄを合わす",
"ﾎﾙﾀﾞｰ部のｵｰﾄSW配線のﾏｰｷﾝｸﾞをﾀｲﾏｳﾝﾄに合わす",
"ﾎﾙﾀﾞｰ部のｵｰﾄSW配線はｴｱﾁｭｰﾌﾞの下側になる事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｾﾝｻｰ配線ﾏｰｷﾝｸﾞを合わす",
"ｵｰﾄSW配線ﾏｰｷﾝｸﾞを合わす (2本)",
"ｴｱﾁｭｰﾌﾞ",
"ﾛｰﾄﾞｾﾙ配線はｾﾝｻｰ配線に沿わす",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ部ｼﾘﾝﾀﾞｴｱﾁｭｰﾌﾞ接続",
"WorkItems": [
"1. にTUBE を接続【2本】"
],
"WorkPoints": [
"【長さ70mm】",
"【長さ70mm】",
"ﾎﾙﾀﾞｰ部ｼﾘﾝﾀﾞｰへﾁｭｰﾌﾞ接続【2本】",
"反対側はSD-A046151-115にて接続"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"Aﾎﾟｰﾄﾌﾟﾚｰﾄ上昇側"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ部取付",
"WorkItems": [
"1. に をBOLT WASHER にて取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. にGUIDE PLATE をBOLT で取付",
"2. に1.完成品をCOLLAR BOLT で取付",
"1. にGUIDE PLATE をBOLT で取付",
"2. に1.完成品をCOLLAR BOLT で取付"
],
"WorkPoints": [
" の凸の向きをGUIDE PLATE 側にすること",
" の凸の向きをGUIDE PLATE 側にすること"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｸﾗﾝﾌﾟ部取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "40cN･m",
"WorkName": "ｸﾗﾝﾌﾟ部取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体配管1/6",
"WorkItems": [
"2. にTUBE を接続 ※略図黒線",
"3. 清掃部上昇用ﾁｭｰﾌﾞ接続 ※略図橙線",
"4. 清掃部下降用ﾁｭｰﾌﾞ接続 ※略図黒線",
"1. にTUBE を接続 ※略図橙線"
],
"WorkPoints": [
"204【長さ185mm】",
"203【長さ150mm】",
"TUBE ｴｱﾁｭｰﾌﾞ Φ4黒 185mm",
"ｼｬｯﾀｰ(閉) ﾊﾞﾙﾌﾞAﾎﾟｰﾄ ~ ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ",
"TUBE ｴｱﾁｭｰﾌﾞ Φ4黒 150mm",
"ｼｬｯﾀｰ(開) ﾊﾞﾙﾌﾞBﾎﾟｰﾄ ~ ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ",
"清掃部上昇 Φ4黒 ﾏｰｷﾝｸﾞあり",
"清掃部上昇 ﾊﾞﾙﾌﾞAﾎﾟｰﾄ ~ ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ",
"清掃部下降 Φ4黒 ﾏｰｷﾝｸﾞなし",
"清掃部下降 ﾊﾞﾙﾌﾞBﾎﾟｰﾄ ~ ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体配管2/6",
"WorkItems": [
"1. にTUBE を接続 ※略図橙線",
"2. TUBE ｴｱﾁｭｰﾌﾞに識別(Aﾎﾟｰﾄ)ﾏｰｷﾝｸﾞ"
],
"WorkPoints": [
"Bﾎﾟｰﾄ【長さ450mm】",
"Aﾎﾟｰﾄ【長さ450mm】",
"ﾛｯｸ用(行き限)ﾊﾞﾙﾌﾞAﾎﾟｰﾄ ※略図橙色線",
"ﾛｯｸ用(戻り限)ﾊﾞﾙﾌﾞBﾎﾟｰﾄ ※略図黒色線",
"略図橙色線のｴｱﾁｭｰﾌﾞ端面より30mm程度の位置にﾏｰｷﾝｸﾞ",
"TUBE ｴｱﾁｭｰﾌﾞ Φ4黒 450mm",
"反対側はSD-A046151-118にて接続"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"識別ﾏｰｷﾝｸﾞ"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体配管3/6",
"WorkItems": [
"1. のｴｱﾁｭｰﾌﾞ接続 ※略図橙線",
"2. のｴｱﾁｭｰﾌﾞを接続 ※略図橙線"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ上昇用(行き限)ﾊﾞﾙﾌﾞAﾎﾟｰﾄ ~ ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ",
"必要部分のみ描いています",
"【注意】 ﾛｯｸ用ﾁｭｰﾌﾞの上になる様に引き廻す",
"ﾌﾟﾚｰﾄ下降用(戻り限)ﾊﾞﾙﾌﾞBﾎﾟｰﾄ ~ ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ",
"【注意】 ﾛｯｸ用ﾁｭｰﾌﾞの上になる様に引き廻す",
"必要部分のみ描いています",
"ｴｱﾁｭｰﾌﾞ Φ4黒 70mm",
"ｴｱﾁｭｰﾌﾞ Φ4黒 70mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "本体配管4/6",
"WorkItems": [
"2. ｼｬｯﾀｰ【閉】側ｴｱﾁｭｰﾌﾞに識別ﾏｰｷﾝｸﾞ実施",
"1. にTUBE を接続",
"3. ｴｱﾁｭｰﾌﾞを結束",
"2. ｼｬｯﾀｰ【閉】側ｴｱﾁｭｰﾌﾞに識別ﾏｰｷﾝｸﾞ実施",
"1. にTUBE を接続",
"3. ｴｱﾁｭｰﾌﾞを結束"
],
"WorkPoints": [
"TUBE ｴｱﾁｭｰﾌﾞ Φ4黒 365mm",
"ｼｬｯﾀｰ開用継手 ※略図上側ｴｱﾁｭｰﾌﾞ",
"ｼｬｯﾀｰ閉用継手 ※略図下側ｴｱﾁｭｰﾌﾞ",
"ｴｱﾁｭｰﾌﾞ端面より30mm程度の位置にﾏｰｷﾝｸﾞ",
"ｼﾞｮｲﾝﾄ差込口より145mmの位置にﾏｰｷﾝｸﾞ",
"ﾌｯｸ部のﾋﾟﾝ(青丸部分)を目印にし､継手やｴｱﾁｭｰﾌﾞの角度を合わせ結束",
"TUBE ｴｱﾁｭｰﾌﾞ Φ4黒 365mm",
"ｼｬｯﾀｰ開用継手 ※略図上側ｴｱﾁｭｰﾌﾞ",
"ｼｬｯﾀｰ閉用継手 ※略図下側ｴｱﾁｭｰﾌﾞ",
"ｴｱﾁｭｰﾌﾞ端面より30mm程度の位置にﾏｰｷﾝｸﾞ",
"ｼﾞｮｲﾝﾄ差込口より145mmの位置にﾏｰｷﾝｸﾞ",
"ﾌｯｸ部のﾋﾟﾝ(青丸部分)を目印にし､継手やｴｱﾁｭｰﾌﾞの角度を合わせ結束"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "本体配管5/6",
"WorkItems": [],
"WorkPoints": [
"必要部分のみ描いています",
"下降時､配管とﾊﾟﾚｯﾄの間が8mm以上である事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"8mm以上",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "8㎜以上になっている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体配管6/6",
"WorkItems": [
"1. の配管を接続し結束"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｼｬｯﾀｰ(開)識別ﾏｰｷﾝｸﾞ",
"ﾛｯｸｼﾘﾝﾀﾞｰ(行き限)識別ﾏｰｷﾝｸﾞ"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓﾆﾀｰ前段取り1/2",
"WorkItems": [
"2. 製品型式･ｼﾘｱﾙﾅﾝﾊﾞｰ確認",
"3. MONITOR の取付ﾌﾞﾗｹｯﾄのﾈｼﾞをBOLT WASHER と交換",
"1. MONITOR の検査表･保証書の確認",
"4. 端子ｶﾊﾞｰ(小)取り外し"
],
"WorkPoints": [
"取付は仮取付",
"既存のﾈｼﾞは廃棄",
"端子接続後に取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表MONITOR :部品検査",
"検査表MONITOR :部品検査",
"WEPJ-G002-C040"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式を確認",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓﾆﾀｰ前段取り1/2",
"WorkItems": [
"2. 製品型式･ｼﾘｱﾙﾅﾝﾊﾞｰ確認",
"3. MONITOR の取付ﾌﾞﾗｹｯﾄのﾈｼﾞをBOLT WASHER と交換",
"1. MONITOR の検査表･保証書の確認",
"4. 端子ｶﾊﾞｰ(小)取り外し"
],
"WorkPoints": [
"取付は仮取付",
"既存のﾈｼﾞは廃棄",
"端子接続後に取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表MONITOR :部品検査",
"検査表MONITOR :部品検査",
"WEPJ-G002-C040"
]
} | {
"QualityItem": "検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "検査表の有無を確認",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓﾆﾀｰ前段取り1/2",
"WorkItems": [
"2. 製品型式･ｼﾘｱﾙﾅﾝﾊﾞｰ確認",
"3. MONITOR の取付ﾌﾞﾗｹｯﾄのﾈｼﾞをBOLT WASHER と交換",
"1. MONITOR の検査表･保証書の確認",
"4. 端子ｶﾊﾞｰ(小)取り外し"
],
"WorkPoints": [
"取付は仮取付",
"既存のﾈｼﾞは廃棄",
"端子接続後に取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表MONITOR :部品検査",
"検査表MONITOR :部品検査"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "50cN･m",
"WorkName": "ﾓﾆﾀｰ前段取り2/2",
"WorkItems": [
"1. にCABLE CABLE CABLE CABLE CABLE CABLE を接続",
"2. 端子ｶﾊﾞｰ(透明ｶﾊﾞｰ小)取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"OCMB411b",
"未接続",
"O2B411",
"未接続",
"I1B411",
"未接続",
"I3B411",
"I4B411",
"OCMB411a",
"ICOB411",
"50cN･m",
"-B411",
"GNDB411",
"+B411",
"80cN･m",
"検査表 :配線接続確認 & 締付ﾄﾙｸ",
"50cN･m"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "80cN･m",
"WorkName": "ﾓﾆﾀｰ前段取り2/2",
"WorkItems": [
"1. にCABLE CABLE CABLE CABLE CABLE CABLE を接続",
"2. 端子ｶﾊﾞｰ(透明ｶﾊﾞｰ小)取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"OCMB411b",
"未接続",
"O2B411",
"未接続",
"I1B411",
"未接続",
"I3B411",
"I4B411",
"OCMB411a",
"ICOB411",
"50cN･m",
"-B411",
"GNDB411",
"+B411",
"80cN･m",
"検査表 :配線接続確認 & 締付ﾄﾙｸ",
"50cN･m"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓﾆﾀｰ前段取り2/2",
"WorkItems": [
"1. にCABLE CABLE CABLE CABLE CABLE CABLE を接続",
"2. 端子ｶﾊﾞｰ(透明ｶﾊﾞｰ小)取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"OCMB411b",
"未接続",
"O2B411",
"未接続",
"I1B411",
"未接続",
"I3B411",
"I4B411",
"OCMB411a",
"ICOB411",
"50cN･m",
"-B411",
"GNDB411",
"+B411",
"80cN･m",
"検査表 :配線接続確認 & 締付ﾄﾙｸ",
"50cN･m",
"WEPJ-G002-C040"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "80cN･m",
"WorkName": "本体制御1/14",
"WorkItems": [
"2. 端子ｶﾊﾞｰ(透明ｶﾊﾞｰ大)取付",
"1. のﾛｰﾄﾞｾﾙ配線を に接続"
],
"WorkPoints": [
"端子ｶﾊﾞｰ(透明ｶﾊﾞｰ大)取り外し",
"端子ｶﾊﾞｰ(透明ｶﾊﾞｰ大)"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"80cN･m",
"AB411",
"BB411",
"CB411",
"DB411",
"EB411",
"+B411",
"−B411",
"検査表 :配線接続確認 & 締付ﾄﾙｸ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体制御1/14",
"WorkItems": [
"2. 端子ｶﾊﾞｰ(透明ｶﾊﾞｰ大)取付",
"1. のﾛｰﾄﾞｾﾙ配線を に接続"
],
"WorkPoints": [
"端子ｶﾊﾞｰ(透明ｶﾊﾞｰ大)取り外し",
"端子ｶﾊﾞｰ(透明ｶﾊﾞｰ大)"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"80cN･m",
"AB411",
"BB411",
"CB411",
"DB411",
"EB411",
"+B411",
"−B411",
"検査表 :配線接続確認 & 締付ﾄﾙｸ",
"WEPJ-G002-C040"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体制御2/14",
"WorkItems": [
"3. 2完成品の配線結束",
"★2. 1完成品にCABLE を取付",
"★1. のｸﾗﾝﾌﾟ部配線ｺﾈｸﾀ接続"
],
"WorkPoints": [
"上基板の【CN1】に接続",
"上基板の【CN6】と下基板の【CN1】に接続",
"【CN1】",
"【CN1】",
"【CN6】"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ｺﾈｸﾀ接続 確認",
"検査表 :ｺﾈｸﾀ接続 確認",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WEPJ-G002-C040"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体制御3/14",
"WorkItems": [
"1. 【R412】を接続",
"2. 【R412】配線を結束",
"3. 【R411】を接続",
"4. 【R413】を接続",
"5. 【R414】を接続",
"6. 【R415】を接続"
],
"WorkPoints": [
"【注意】接続は､傾いて隙間が空く場合があるので確実に接続する事",
"【注意】接続は､傾いて隙間が空く場合があるので確実に接続する事",
" のﾓﾆﾀｰAssyを本体に近づけて､付帯するｺﾈｸﾀｰを接続"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"R412",
"R411",
"R413",
"R414",
"R415",
"検査表 :ｺﾈｸﾀ接続 確認",
"検査表 :ｺﾈｸﾀ接続 確認",
"検査表 :ｺﾈｸﾀ接続 確認",
"検査表 :ｺﾈｸﾀ接続 確認",
"検査表 :ｺﾈｸﾀ接続 確認",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WEPJ-G002-C040"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体制御4/14",
"WorkItems": [
"1. ﾌﾞﾗｹｯﾄに【B101P】を引き回し"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"【B101P】",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体制御5/14",
"WorkItems": [
"1. まとめ仮結束 "
],
"WorkPoints": [
"ﾛｰﾄﾞｾﾙ配線/ﾊﾞﾙﾌﾞ配線/ﾛｯｸｼﾘﾝﾀﾞｰｵｰﾄSW を仮結束",
"必要部分のみ描いています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾛｯｸｼﾘﾝﾀﾞｰ配線【B101P】",
"ﾛｰﾄﾞｾﾙ配線",
"ﾊﾞﾙﾌﾞ配線【R411/R412/R413/R414/R415】",
"仮結束 ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体制御6/14",
"WorkItems": [
"1. のｼｬｯﾀｰ部ｵｰﾄSW配線のﾏｰｷﾝｸﾞ位置にて結束",
"2. 結束間にまとめ結束",
"3. 干渉確認"
],
"WorkPoints": [
"【注意】 ｲﾝｼｭﾛｯｸの頭の向きは奥側 ※下略図参照",
"ﾀｲﾏｳﾝﾄにﾏｰｷﾝｸﾞを合わせ結束",
"略図赤色部分を上昇/下降させ配線の干渉確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ﾏｰｷﾝｸﾞ",
"B104P",
"B106P"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体制御7/14",
"WorkItems": [
"3. 結束",
"2. 前側 黒ｺﾈｸﾀ 【B103P】【B105P】【B107P】取付",
"1. 前側 黒ｺﾈｸﾀ 【B102P】【B104P】【B106P】取付"
],
"WorkPoints": [
"【B101P~B107P】計7本をまとめて結束",
" の必要な部分のみ描いています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体制御8/14",
"WorkItems": [
"★1. にCABLE を接続"
],
"WorkPoints": [
"【CN10】",
"【CN9】",
"【CN7】",
"【B107R】",
"上基板の【CN7】と下基板の【CN10】/【CN9】に接続"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ｺﾈｸﾀ接続 確認",
"WEPJ-G002-C040"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体制御9/14",
"WorkItems": [
"★1. にCABLE を接続"
],
"WorkPoints": [
"【B101R~B106R】を接続"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ｺﾈｸﾀ接続 確認",
"WEPJ-G002-C040"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体制御10/14",
"WorkItems": [
"★1. のﾓﾆﾀｰ配線を接続"
],
"WorkPoints": [
"配線が繋がっている為､配線が張らないように注意しながら作業する事",
"下基板の【CN5】に接続",
"【CN5】"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ｺﾈｸﾀ接続 確認",
"WEPJ-G002-C040"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.