input stringclasses 1 value | instruction stringlengths 222 1.92k | output stringlengths 193 312 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄREAR組立⑦",
"WorkItems": [
"1. FRAME にSUPPORT NUT CABLE-SUPPORT を取付け",
"2. 1.完成品にBRACKET をWASHER BOLT で取付け"
],
"WorkPoints": [
"SUPPORT はNUT とｾｯﾄで使用",
"BRACKET はFRAME と端面合わせ",
"上面",
"内面",
"右面",
"外面",
"左面",
"内面",
"端面合わせ",
"端面合わせ",
"内面",
"右面",
"外面",
"左面",
"上面"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"NUT N014:M6後入れ",
"CABLE-SUPPORT N017"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑｷｯﾄREAR組立⑦",
"WorkItems": [
"1. FRAME にSUPPORT NUT CABLE-SUPPORT を取付け",
"2. 1.完成品にBRACKET をWASHER BOLT で取付け"
],
"WorkPoints": [
"SUPPORT はNUT とｾｯﾄで使用",
"BRACKET はFRAME と端面合わせ",
"上面",
"内面",
"右面",
"外面",
"左面",
"内面",
"端面合わせ",
"端面合わせ",
"内面",
"右面",
"外面",
"左面",
"上面"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"NUT N014:M6後入れ",
"CABLE-SUPPORT N017"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄREAR組立⑧",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CABLE-SUPPORT N017"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑｷｯﾄREAR組立⑧",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CABLE-SUPPORT N017"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄREAR組立⑨",
"WorkItems": [
"1. FRAME にSUPPORT NUT を取付け",
"2. 1.完成品にBRACKET をWASHER BOLT で取付け"
],
"WorkPoints": [
"SUPPORT はNUT とｾｯﾄで使用",
"BRACKET はFRAME と端面合わせ",
"上面",
"内面",
"右面",
"外面",
"左面",
"内面",
"端面合わせ",
"端面合わせ",
"内面",
"右面",
"外面",
"左面",
"上面"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"NUT N014:M6後入れ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑｷｯﾄREAR組立⑨",
"WorkItems": [
"1. FRAME にSUPPORT NUT を取付け",
"2. 1.完成品にBRACKET をWASHER BOLT で取付け"
],
"WorkPoints": [
"SUPPORT はNUT とｾｯﾄで使用",
"BRACKET はFRAME と端面合わせ",
"上面",
"内面",
"右面",
"外面",
"左面",
"内面",
"端面合わせ",
"端面合わせ",
"内面",
"右面",
"外面",
"左面",
"上面"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"NUT N014:M6後入れ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄREAR組立⑩",
"WorkItems": [
"1. FRAME にSUPPORT NUT を取付け",
"2. 1.完成品にBRACKET をWASHER BOLT で取付け"
],
"WorkPoints": [
"SUPPORT はNUT とｾｯﾄで使用",
"BRACKET はFRAME と端面合わせ",
"上面",
"内面",
"右面",
"外面",
"左面",
"内面",
"端面合わせ",
"端面合わせ",
"内面",
"右面",
"外面",
"左面",
"上面"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"NUT N014:M6後入れ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑｷｯﾄREAR組立⑩",
"WorkItems": [
"1. FRAME にSUPPORT NUT を取付け",
"2. 1.完成品にBRACKET をWASHER BOLT で取付け"
],
"WorkPoints": [
"SUPPORT はNUT とｾｯﾄで使用",
"BRACKET はFRAME と端面合わせ",
"上面",
"内面",
"右面",
"外面",
"左面",
"内面",
"端面合わせ",
"端面合わせ",
"内面",
"右面",
"外面",
"左面",
"上面"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"NUT N014:M6後入れ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄREAR組立⑪",
"WorkItems": [
"1. をWASHER BOLT で連結"
],
"WorkPoints": [
"全て内面で合わせる",
"は⑨BOLT を使用"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"320㎜",
"177.5㎜",
"177.5㎜",
"487.5㎜"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑｷｯﾄREAR組立⑪",
"WorkItems": [
"1. をWASHER BOLT で連結"
],
"WorkPoints": [
"全て内面で合わせる",
"は⑨BOLT を使用"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"320㎜",
"177.5㎜",
"177.5㎜",
"487.5㎜"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄREAR組立⑫",
"WorkItems": [
"1. をWASHER BOLT で連結"
],
"WorkPoints": [
"全て内面で合わせる",
"はWASHER BOLT を使用"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"177.5㎜",
"177.5㎜"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑｷｯﾄREAR組立⑫",
"WorkItems": [
"1. をWASHER BOLT で連結"
],
"WorkPoints": [
"全て内面で合わせる",
"はWASHER BOLT を使用"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"177.5㎜",
"177.5㎜"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "正流れﾌﾚｰﾑｷｯﾄFRONT2組立",
"WorkItems": [
"1. FRAME にSUPPORT NUT NUT CABLE-SUPPORT を取付け"
],
"WorkPoints": [
"SUPPORT はNUT NUT とｾｯﾄで使用"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"NUT N005:M6後入れ",
"NUT N006:M4後入れ",
"N010"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立①",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"扉上側",
"A矢視図",
"中央ﾌﾚｰﾑ固定用の穴が扉下側になるよう組付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M6",
"M5",
"M4",
"M3",
"×2",
"この作業では同じものを2個製作",
"ﾅｯﾄ挿入面",
"×2"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立②",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT ･NUT ･CAP を取付"
],
"WorkPoints": [
"扉右側",
"風船色ﾅｯﾄｻｲｽﾞ",
"裏面図",
"ﾀｯﾌﾟ穴が扉左側になるよう組付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×4",
"この作業では同じものを2個製作",
"ﾅｯﾄ挿入面",
"M6",
"M5",
"M4",
"M3"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立③",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT を取付"
],
"WorkPoints": [
"ﾌﾗｯﾄ面",
"扉上側",
"風船色ﾅｯﾄｻｲｽﾞ",
"中央ﾌﾚｰﾑ固定用の穴が扉下側になるよう組付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×2",
"この作業では同じものを2個製作",
"ﾅｯﾄ挿入面",
"M6",
"M5",
"M4",
"M3",
"×2",
"×2",
"×2"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立④",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT ･NUT ･CAP を取付",
"2. 1.完成品にCAP を取付"
],
"WorkPoints": [
"ﾌﾗｯﾄ面",
"扉左側",
"風船色ﾅｯﾄｻｲｽﾞ",
"A面",
"B面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×2",
"この作業では同じものを2個製作",
"ﾅｯﾄ挿入面B",
"M6",
"M5",
"M4",
"M3",
"×2",
"ﾅｯﾄ挿入面A",
"×2",
"×2",
"1.完成品"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑤",
"WorkItems": [
"1. CLAMP を指定の長さにｶｯﾄ",
"1. 1.完成品･ ･ ･ ･ ･FRAME ･PANEL ･PANEL をBOLT で組付け"
],
"WorkPoints": [
"取っ手取付用穴"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"外側面",
"L=716.5",
"L=716.5",
"L=430",
"L=275"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑥",
"WorkItems": [
"1. にHINGE をSCREW で取付"
],
"WorkPoints": [
"取っ手取付用穴",
"白ﾌﾟﾗｽﾁｯｸが下になる様に取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"外側面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑦",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-031"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-031",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑦",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-031"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-031",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑦",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑧",
"WorkItems": [
"1. に をBOLT ･WASHER で取付"
],
"WorkPoints": [
"取っ手取付用穴"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"×2",
"内側面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑨",
"WorkItems": [
"1. にCATCH をBOLT で取付"
],
"WorkPoints": [
"取っ手取付用穴"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"×2",
"内側面",
"×2"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑩",
"WorkItems": [
"1. にBRACKET ･PLATE をBOLT ･WASHER ･BOLT で取付"
],
"WorkPoints": [
"ﾌﾚｰﾑ下面に直角平行に取付",
"取っ手取付用穴",
"ﾌﾚｰﾑに対して直角平行に取付",
"A矢視図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"内側面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑪",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "ﾊﾞﾘ確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "-",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "圧入治具ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-2215",
"3mm",
"出代: 3mm",
"ﾌﾞﾛｯｸ"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾋﾟﾝ出代:3㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "圧入治具ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"2.0mm",
"･ﾋﾟﾝ出代: 2mm",
"･各ﾋﾟﾝはﾃｰﾊﾟ側より 圧入する事｡",
"2. 1.にPIN を圧入する｡",
"FM-3202 2/3",
"FM-3202 3/3",
"拡大図FM-3202 3/3",
"FM-3202 -1",
"FM-3202 -2",
"*.段差を逃がす"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾋﾟﾝ出代:2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "圧入治具ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-3212",
"30.5mm",
"◆2. 1.ﾋﾟﾝにｸﾞﾘｰｽを塗布する｡",
"ｸﾞﾘｰｽを塗布する(米粒/2粒) 2ヵ所全体に薄く延ばす｡",
"ﾃｰﾊﾟ"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾋﾟﾝ出代:30.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-3212",
"30.5mm",
"◆2. 1.ﾋﾟﾝにｸﾞﾘｰｽを塗布する｡",
"ｸﾞﾘｰｽを塗布する(米粒/2粒) 2ヵ所全体に薄く延ばす｡",
"ﾃｰﾊﾟ"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒/2粒､2ヵ所",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "圧入治具ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立⑤",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-2250(2)",
"BEARING ",
"※D-pin(2ヶ所)と穴(2ヶ所)を はめ込む(赤矢印参照)",
"※上側の列2ヶ所に挿入の事｡",
"2.ﾊﾝﾄﾞﾌﾟﾚｽでPIN を1.に圧入する｡",
"PIN ",
"･ﾃｰﾊﾟ側を 上向きに圧入",
"1mm",
"･出代: 1mm",
"3.2.にWASHER を挿入する",
"*.ﾍﾞｱﾘﾝｸﾞ圧入時､ HW 入れ忘れ防止の為"
]
} | {
"QualityItem": "圧入確認出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾋﾟﾝ出代:1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "圧入治具ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立⑥",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1･治具(FM-3203) 下ﾌﾟﾚｰﾄにﾍﾞｱﾘﾝｸﾞをｾｯﾄする2･上ﾌﾟﾚｰﾄをD-ﾋﾟﾝ穴に合わせ､はめ込む",
"BEARING ",
"･出代: 1mm",
"ﾃｰﾊﾟ",
"2. 1.にWASHER を挿入する｡",
"*.ﾍﾞｱﾘﾝｸﾞ圧入時､ ﾜｯｼｬｰの入れ忘れ防止の為｡"
]
} | {
"QualityItem": "圧入確認出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾋﾟﾝ出代:1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊﾝﾄﾞﾌﾟﾚｽ圧入治具",
"Size": "",
"ToolOther": "FM-3271-1FM-3271-2",
"WorkName": "ﾍﾞｱﾘﾝｸﾞ挿入①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･後 側",
"･⑩K006 挿入図",
"1.･治具(FM-3271-1)にｾｯﾄする",
"裏面･ﾎﾞﾙﾄで固定",
"2.⑧に⑩を挿入する｡",
"M3小径",
"FM-3271-1",
"FM-3271-2",
"治具ｾﾝﾀｰにて圧入の事",
"*､地下置きにて圧入",
"治具ｾﾝﾀｰにて圧入の事"
]
} | {
"QualityItem": "圧入確認",
"ToolManageNo": "FM-3271-1FM-3271-2",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "-",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊﾝﾄﾞﾌﾟﾚｽ圧入治具",
"Size": "",
"ToolOther": "FM-3271-1FM-3271-2",
"WorkName": "ﾍﾞｱﾘﾝｸﾞ挿入②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･⑩K006 挿入図",
"裏面･ﾎﾞﾙﾄで固定",
"･治具(FM-3271-1)にｾｯﾄする",
"2.⑧に⑩を挿入する｡",
"M3小径",
"治具ｾﾝﾀｰにて圧入の事",
"治具ｾﾝﾀｰにて圧入の事",
"*､地下置きにて圧入",
"FM-3271-2",
"FM-3271-1"
]
} | {
"QualityItem": "圧入確認",
"ToolManageNo": "FM-3271-1FM-3271-2",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "-",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立⑦",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆ ﾍﾞｱﾘﾝｸﾞ外周に ｸﾞﾘｰｽ(LCG100) 塗布",
"･米粒/1粒",
"･各 ｺﾞﾏ粒/1粒",
"･米粒/1粒",
"･各 ｺﾞﾏ粒/1粒"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒/1粒ｺﾞﾏ粒/1粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾍﾞｰｽ組立⑧",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"SPACER ",
"SPACER ",
"◆2. 1.のﾍﾞｱﾘﾝｸﾞ外周にｸﾞﾘｰｽを塗布する｡",
"◆ｸﾞﾘｰｽ塗布(LCG100)ｺﾞﾏ粒/1粒(4ヵ所)",
"*.ﾍﾞｱﾘﾝｸﾞ 隅にﾏｰｶｰを付ける｡ (SD-0130281-016 にて回転確認の為)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立⑧",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"SPACER ",
"SPACER ",
"◆2. 1.のﾍﾞｱﾘﾝｸﾞ外周にｸﾞﾘｰｽを塗布する｡",
"◆ｸﾞﾘｰｽ塗布(LCG100)ｺﾞﾏ粒/1粒(4ヵ所)",
"*.ﾍﾞｱﾘﾝｸﾞ 隅にﾏｰｶｰを付ける｡ (SD-0130281-016 にて回転確認の為)"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒/1粒､4ヵ所",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾄｯﾊﾟｰ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に接着米粒/2粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "接着剤ｽｰﾊﾟｰX",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ(P002)面処理",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"*.ｴｯｼﾞ部に砥石を掛ける"
]
} | {
"QualityItem": "ﾊﾞﾘ確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "-",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "周辺部品･面処理",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"2. BLOCK にｱﾙｶﾝｻｽを掛ける｡",
"･指示分に油砥石を掛け､ﾊﾞﾘ等の無き事の確認を行う｡",
"3. BLOCK にｱﾙｶﾝｻｽを掛ける｡",
"･指示分に油砥石を掛け､ﾊﾞﾘ等の無き事の確認を行う｡"
]
} | {
"QualityItem": "ﾊﾞﾘ確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "-",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ取付①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"←方向に当付け取付",
"･切吹き部に取付(2ヵ所)",
"･ｼｬｯﾀｰに対して､隙間無き事"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "-",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･本締結(SD-0130281-016)締付けﾄﾙｸ:150cN･m",
"◆2. 1.に⑨WASHER を挿入する｡",
"･⑨にWASHER をｸﾞﾘｰｽで貼付け､1.を入れる",
"3. 2.にCOLLAR BLOCK ⑩をBOLT BOLT で仮取付け｡",
"*.ｽﾌﾟﾘﾝｸﾞを押え挿入"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒/2粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ取付③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･締付けﾄﾙｸ: 150cN･m",
"*.ｶﾞｲﾄﾞがﾍﾞｱﾘﾝｸﾞと 干渉し無い事｡",
"*.ﾍﾞｱﾘﾝｸﾞの摺動がｶﾞﾀがなく､ｽﾑｰｽﾞである事を確認する｡",
"･調整後､ﾎﾞﾙﾄを締結する｡"
]
} | {
"QualityItem": "摺動確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｼｬｯﾀｰ動作がｽﾑｰｽﾞである事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｼｬｯﾀｰ取付③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･締付けﾄﾙｸ: 150cN･m",
"*.ｶﾞｲﾄﾞがﾍﾞｱﾘﾝｸﾞと 干渉し無い事｡",
"*.ﾍﾞｱﾘﾝｸﾞの摺動がｶﾞﾀがなく､ｽﾑｰｽﾞである事を確認する｡",
"･調整後､ﾎﾞﾙﾄを締結する｡"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "95cN･m",
"WorkName": "ﾌﾞﾛｯｸ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･締付けﾄﾙｸ:95cN･m",
"･GUIDE を右側に押し当てて取付け｡",
"2. ⑧にGUIDE をSPACER BOLT で取付け｡"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆/1粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "95cN･m",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･締付けﾄﾙｸ:95cN･m",
"･GUIDE を右側に押し当てて取付け｡",
"2. ⑧にGUIDE をSPACER BOLT で取付け｡"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｽﾍﾟｰｻ取付ｶﾞｰﾄﾞ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"2. 1.にGUARD をBOLT WASHER で取付け｡",
"･矢印方向･垂直に押し当てて取付",
"･締付けﾄﾙｸ:95cN･m",
"*.水平に取付",
"*.ﾏｰｶｰ位置 (内側)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｽﾍﾟｰｻ取付ｶﾞｰﾄﾞ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"2. 1.にGUARD をBOLT WASHER で取付け｡",
"･矢印方向･垂直に押し当てて取付",
"･締付けﾄﾙｸ:95cN･m",
"*.水平に取付",
"*.ﾏｰｶｰ位置 (内側)"
]
} | {
"QualityItem": "取付確認締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "動作確認治具",
"Size": "",
"ToolOther": "FM-2411",
"WorkName": "動作確認",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･着脱の際､引っ掛かりが無い事",
"2.ｼｬｯﾀｰの動作確認を実施する｡",
"※1. ｷｯﾄ検査表 :ｼｬｯﾀｰ動作確認",
"･最大過重 :4N 以下",
"WCQP-C010-049"
]
} | {
"QualityItem": "着脱確認",
"ToolManageNo": "FM-2411",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "引っ掛かりの無い事",
"Method": "手感",
"RecordMethod": "WCQP-C010-049",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "動作確認",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･着脱の際､引っ掛かりが無い事",
"2.ｼｬｯﾀｰの動作確認を実施する｡",
"※1. ｷｯﾄ検査表 :ｼｬｯﾀｰ動作確認",
"･最大過重 :4N 以下",
"WCQP-C010-049"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "最大荷重4N以下",
"Method": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"RecordMethod": "WCQP-C010-049",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｾﾝﾀｰ合せ"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼﾘｱﾙﾗﾍﾞﾙ貼付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "150cN･m",
"WorkName": "ｶﾗｰ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｶﾗｰ向き",
"･ｶﾗｰの取付方向 (Dｶｯﾄ部が横に来る様に取付)"
]
} | {
"QualityItem": "方向確認締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2169",
"WorkName": "機能検査",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"2･治具ﾉｽﾞﾙ 開閉確認を実施する｡",
"SW 上側 ｼｬｯﾀｰ \"開 下側 ｼｬｯﾀｰ \"閉",
"*､ｼｬｯﾀｰ開閉が引っ掛りがなく､ｽﾑｰｽﾞである事",
"*､A部のﾚﾊﾞｰを押して､ﾁｪﾝｼﾞｬｰがｽﾑｰｽﾞに落下する事",
"*.ﾉｽﾞﾙをｾｯﾄし､ｽﾑｰｽﾞである事を確認する",
"ｼｬｯﾀｰ\"開､ﾉｽﾞﾙｾｯﾄ確認",
"ｼｬｯﾀｰ\"閉､ﾉｽﾞﾙ抜け確認",
"検査用ﾉｽﾞﾙ",
"※1.ｷｯﾄ検査表 : ﾉｽﾞﾙｾｯﾄ確認 (WCQP-C010-049)",
"*.5ヵ所全て確認の事"
]
} | {
"QualityItem": "自重落下確認",
"ToolManageNo": "FM-2169",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾁｪﾝｼﾞｬｰがｽﾑｰｽﾞに落下出きる事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾁｪｯｶｰ検査ﾉｽﾞﾙ",
"Size": "",
"ToolOther": "FM-2169",
"WorkName": "機能検査",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"2･治具ﾉｽﾞﾙ 開閉確認を実施する｡",
"SW 上側 ｼｬｯﾀｰ \"開 下側 ｼｬｯﾀｰ \"閉",
"*､ｼｬｯﾀｰ開閉が引っ掛りがなく､ｽﾑｰｽﾞである事",
"*､A部のﾚﾊﾞｰを押して､ﾁｪﾝｼﾞｬｰがｽﾑｰｽﾞに落下する事",
"*.ﾉｽﾞﾙをｾｯﾄし､ｽﾑｰｽﾞである事を確認する",
"ｼｬｯﾀｰ\"開､ﾉｽﾞﾙｾｯﾄ確認",
"ｼｬｯﾀｰ\"閉､ﾉｽﾞﾙ抜け確認",
"検査用ﾉｽﾞﾙ",
"※1.ｷｯﾄ検査表 : ﾉｽﾞﾙｾｯﾄ確認 (WCQP-C010-049)",
"*.5ヵ所全て確認の事",
"WCQP-C010-049"
]
} | {
"QualityItem": "ﾉｽﾞﾙｾｯﾄ確認",
"ToolManageNo": "FM-2169",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾉｽﾞﾙがｽﾑｰｽﾞにｾｯﾄ出きる事",
"Method": "ﾁｪｯｶｰ",
"RecordMethod": "WCQP-C010-049",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｾﾝｻｰ部組立",
"WorkItems": [
"1. BRACKET にSENSOR をNUT-PLATE BOLT で取付ける(2個)",
"2. 1の完成品にBRACKET をWASHER WASHER BOLT で取付ける",
"3. 2の完成品にCABLE-SUPPORT を取付ける(2個)"
],
"WorkPoints": [
"FT4向き",
"測定位置はｾﾝｻ中心部 各位置より±0.5㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"57.5mm",
"75.1mm",
"取付位置"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾟｰﾘｰ部組立",
"WorkItems": [
"1. PLATE にPLATE をBOLT で取付ける",
"2. 1の完成品にｱｲﾄﾞﾗｰﾋﾟﾝ をWASHER WASHER NUT で取付ける(2個)",
"3. 2の完成品にPULLEY PULLEY を挿入しC-RING を取付ける"
],
"WorkPoints": [
"青線部の端面を合わせる",
"WASHER 入れる場所注意",
"ｱｲﾄﾞﾗｰﾋﾟﾝ の取付向き注意",
"C-RING は平らな面を外側に向けて付ける",
"PULLEY はこの向きになるように取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"PULLEY PULLEY ﾌﾟｰﾘｰ",
"C-RING ",
"ｱｲﾄﾞﾗｰﾋﾟﾝ ﾋﾟﾝ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "5㎜",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰ部組立_1",
"WorkItems": [],
"WorkPoints": [
"KEY溝側",
"隙間 5mmﾌﾞﾛｯｸｹﾞｰｼﾞ使用",
"Dｶｯﾄ側",
"KEY溝",
"TORQUE-LIMITER の付属ﾈｼﾞ(2個)は取り外して破棄する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"外径ｷｰ",
"TORQUE-LIMITER に付属",
"Dｶｯﾄ面の止めねじが正面に対し､左側にKEY溝の止めねじある向きにする"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:5㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "170cN･m",
"WorkName": "ﾓｰﾀｰ部組立_1",
"WorkItems": [],
"WorkPoints": [
"KEY溝側",
"隙間 5mmﾌﾞﾛｯｸｹﾞｰｼﾞ使用",
"Dｶｯﾄ側",
"KEY溝",
"TORQUE-LIMITER の付属ﾈｼﾞ(2個)は取り外して破棄する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"外径ｷｰ",
"TORQUE-LIMITER に付属",
"Dｶｯﾄ面の止めねじが正面に対し､左側にKEY溝の止めねじある向きにする"
]
} | {
"QualityItem": "締付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "170cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀｰ部組立_2",
"WorkItems": [
"2. 1の完成品にBRACKET をBOLT WASHER で取付ける",
"1. にﾌﾟｰﾘ(1) を挿入し､ｽﾄｯﾌﾟﾘﾝｸﾞを取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｽﾄｯﾌﾟﾘﾝｸﾞ(N005付属品)",
"N005",
"N005(TORQUE-LIMITER)",
"N005 ﾄﾙｸﾃﾝﾀﾞｰ",
"ﾌﾟｰﾘ(1) ﾌﾟｰﾘｰ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_1",
"WorkItems": [
"3. 2の完成品にBALL-SCREW を挿入しBOLT WASHER で取付ける",
"1. BEARING の余分な油を清掃後､BEARING を重ねてNUT に挿入する",
"2. 1の完成品にKEY を圧入する"
],
"WorkPoints": [
"この作業ﾍﾟｰｼﾞでは同じ物を2個製作する",
"BEARING の側面のﾏｰｸをVの字に合わせる事",
"BALL-SCREW の余分な油清掃と両端にｺﾞﾑが付いているので外し忘れないようにすること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"Vﾏｰｸ",
"このでは同じ物を2個製作",
"取付け方向に注意!この部品には方向性があります｡",
"隙間無き事"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_2",
"WorkItems": [
"2. LOCK-NUT を1の完成品に締め付けて固定する",
"1. にﾌﾟﾚｰﾄ を挿入後､ﾌﾟｰﾘ(2) とﾌﾟｰﾘ(3) を挿入する｡",
"3. 2の完成品をSCREW で固定する"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ はﾌﾟｰﾘｰ側にｻﾞｸﾞﾘ穴があるように取付ける",
"LOCK-NUT 取付向き注意",
"締め終えたら注記箇所に隙間が無い事を確認",
"ﾌﾟｰﾘ(2) は1本(ﾈｼﾞがKEY溝側にしか入らない)",
"ﾌﾟｰﾘ(3) は2本"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"〇部をﾓﾝｷｰﾚﾝﾁで固定しLOCK-NUT を締め付ける"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "隙間無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_3",
"WorkItems": [
"1. にﾌﾟﾚｰﾄ を挿入後､ｽﾍﾟｰｻ とﾌﾟｰﾘ(2) を挿入する",
"2. LOCK-NUT を1の完成品に締め付けて固定する",
"3. 2の完成品をSCREW で固定する"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ はﾌﾟｰﾘｰ側にｻﾞｸﾞﾘ穴があるように取付ける",
"LOCK-NUT 取付向き注意",
"締め終えたら注記箇所に隙間が無い事を確認",
"ﾌﾟｰﾘ(2) は1本(ﾈｼﾞがKEY溝側にしか入らない)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"〇部をﾓﾝｷｰﾚﾝﾁで固定しLOCK-NUT を締め付ける"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "隙間無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_4",
"WorkItems": [
"1. ｹｰｽ にBUSH を挿入しSCREW で取付ける"
],
"WorkPoints": [
"この作業ﾍﾟｰｼﾞでは同じ物を2個製作する",
"BUSH の凹み部分がｹｰｽ の穴と合うように挿入する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｹｰｽ の段付き箇所まで挿入する",
"半透明図",
"断面図",
"段付き箇所",
"取付け方向に注意!この部品には方向性があります｡"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_5",
"WorkItems": [
"1. に を挿入しWASHER BOLT で取付ける"
],
"WorkPoints": [
" と を端面で合わせて取付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"端面を合わせる",
"端面を合わせる"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_6",
"WorkItems": [
"1. に を挿入しWASHER BOLT で取付ける"
],
"WorkPoints": [
" と を端面で合わせて取付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"端面を合わせる",
"端面を合わせる"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_7(ﾓｰﾀｰ側)",
"WorkItems": [
"1. にﾍﾞﾛｰｽﾞ を挿入する",
"2. PIN を挿入しPIN で固定する"
],
"WorkPoints": [
"軸を回しPIN が入るように穴を合わせる",
"PIN とPIN の取付拡大図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾍﾞﾛｰｽﾞ の挿入時は下図3か所の位置関係を確認する",
"軸を回し穴を合わせる",
"Dｶｯﾄ向き",
"ｻﾞｸﾞﾘ穴",
"軸回転",
"取付け方向に注意!この部品には方向性があります｡",
"溝部",
"Dｶｯﾄ位置",
"ｻﾞｸﾞﾘ穴",
"溝部",
"上から見た図"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_8(従動側)",
"WorkItems": [
"1. にﾍﾞﾛｰｽﾞ を挿入する",
"2. PIN を挿入しPIN で固定する"
],
"WorkPoints": [
"軸を回しPIN が入るように穴を合わせる",
"PIN とPIN の取付拡大図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾍﾞﾛｰｽﾞ の挿入時は下図3か所の位置関係を確認する",
"軸を回し穴を合わせる",
"Dｶｯﾄ向き",
"座ｸﾞﾘ穴",
"軸回転",
"取付け方向に注意!この部品には方向性があります｡",
"溝部",
"Dｶｯﾄ位置",
"ｻﾞｸﾞﾘ穴",
"溝部",
"上から見た図"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_9",
"WorkItems": [
"1. と にﾌﾞｯｼｭ を挿入しBOLT で取付ける"
],
"WorkPoints": [
"ﾌﾞｯｼｭ は奥まで挿入してからﾈｼﾞを入れるようにすること",
"ﾓｰﾀｰ側(ﾌﾟｰﾘｰ2個)",
"従動側(ﾌﾟｰﾘｰ1個)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_10",
"WorkItems": [
"2. 1の完成品に をBOLT WASHER で取付ける",
"3. (従動側)に をBOLT WASHER で矢印の方向に仮止めする",
"1. (ﾓｰﾀｰ側)に をBOLT WASHER で矢印の方向に仮止めする"
],
"WorkPoints": [
"ﾓｰﾀｰ側(ﾌﾟｰﾘｰ2個)",
"ﾓｰﾀｰ側(ﾌﾟｰﾘｰ2個)",
"従動側(ﾌﾟｰﾘｰ1個)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"仮止め:SD-A052523-020にて本締め",
"仮止め:SD-A052523-021にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降ﾕﾆｯﾄ組立_11",
"WorkItems": [
"1. PLATE にBOLT NUT を取付ける"
],
"WorkPoints": [
"ﾈｼﾞ出代 7㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:7㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ組立",
"WorkItems": [
"1. CHANNEL にSHAFT をWASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"下から見た図"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Oﾘﾝｸﾞ取付",
"WorkItems": [
"●1. のOリング溝とO-RING を清掃後、O-RING に㉘を塗布し のOリング溝に取付ける",
"2. 1の完成品を㉘で軽く拭く"
],
"WorkPoints": [
"ﾓｰﾀｰ側",
"従動側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"Oﾘﾝｸﾞ溝",
"※Oﾘﾝｸﾞが溝へ正常に挿入されている事を確認する",
"ｸﾞﾘｰｽ塗布 米粒:各1"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部取付",
"WorkItems": [
"1. ⑥の〇で示した部分を㉗㉘で清掃する",
"2. 1の完成品に をWASHER BOLT で取付ける"
],
"WorkPoints": [
"底面から見た図",
"ﾓｰﾀｰ側",
"従動側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります｡"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "T-BELT取付",
"WorkItems": [
"2. の従動側の昇降部にある〇印のﾈｼﾞを緩めﾌﾞﾗｹｯﾄを動かしてT-BELT を張り､再度ねじを仮締めする",
"1. のﾓｰﾀｰ側の昇降部にある〇印のﾈｼﾞを緩めﾓｰﾀｰを動かしてT-BELT を張り､再度ねじを仮締めする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"仮止め:SD-A052523-020にて本締め",
"仮止め:SD-A052523-022にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "U-507",
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾝ調整_1",
"WorkItems": [
"1. ﾓｰﾀｰ側の昇降部の〇印のﾎﾞﾙﾄを緩め､左右に動かしながらﾍﾞﾙﾄﾃﾝｼｮﾝを調整する"
],
"WorkPoints": [
"ﾍﾞﾙﾄ張力計の設定が下記数値になっていることを確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾃﾝｼｮﾝ規格値:50~70N",
"※SD-A018066-019での仮締めを本締結",
"Mass 22.7g/mWidth 12.7mm/RSpan 70mm/R",
"ﾃﾝｼｮﾝ測定ﾎﾟｲﾝﾄ(ｾﾝﾀｰ部)"
]
} | {
"QualityItem": "ﾍﾞﾙﾄﾃﾝｼｮﾝ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "50~70N",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾓｰﾀｰﾌﾞﾚｰｷ解除治具",
"Size": "",
"ToolOther": "FM-3229",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部高さ調整",
"WorkItems": [
"1. のモーターのコネクタに㉖を取付ける",
"2. ㉖のプラグをコンセントに繋ぎ、スイッチをONにする",
"3. ﾓｰﾀｰﾌﾞﾚｰｷ解除後､ のｼｬﾌﾄの出代を調整する"
],
"WorkPoints": [
"ﾓｰﾀｰ",
"治具",
"BKがﾌﾞﾚｰｷ解除のｺﾈｸﾀになる",
"ｼｬﾌﾄ同士がお互いに±0.1㎜以内",
"ﾍﾞﾙﾄを動かすと連結しているので､両方のｼｬﾌﾄが動いてしまう",
"〇印のﾈｼﾞを緩め､ﾍﾞﾙﾄを少し弛ませてﾌﾟｰﾘｰ単体を回すようにすると調整しやすい"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M607BKP",
"M60□BKR",
"M607R",
"ﾓｰﾀｰｺﾈｸﾀ接続",
"ﾌﾞﾚｰｷ解除治具"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "FM-3229",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "-",
"Method": "-",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部高さ調整",
"WorkItems": [],
"WorkPoints": [
"ﾓｰﾀｰ",
"治具",
"BKがﾌﾞﾚｰｷ解除のｺﾈｸﾀになる",
"ｼｬﾌﾄ同士がお互いに±0.1㎜以内",
"ﾍﾞﾙﾄを動かすと連結しているので､両方のｼｬﾌﾄが動いてしまう"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M607BKP",
"M60□BKR",
"M607R",
"ﾓｰﾀｰｺﾈｸﾀ接続"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "±0.1㎜以内",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞﾙﾄ張力計",
"Size": "",
"ToolOther": "U-507",
"WorkName": "ﾍﾞﾙﾄﾃﾝｼｮﾝ調整_2",
"WorkItems": [
"1. 従動側の昇降部の〇印のﾎﾞﾙﾄを緩め､左右に動かしながらﾍﾞﾙﾄﾃﾝｼｮﾝを調整する",
"2. ベルトテンション調整後、シャフトの出代を再度確認し規格内なら㉖を取り外す"
],
"WorkPoints": [
"ﾃﾝｼｮﾝ規格値:50~70N",
"ﾍﾞﾙﾄ張力計の設定が下記数値になっていることを確認する",
"規格外の場合はSD-A052523-021に戻り､再調整をおこなう",
"ﾍﾞﾙﾄの凹凸とﾌﾟｰﾘｰが引っかかってる位置がｽﾞﾚると高さが変わる為､動かす際は注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"※SD-A018066-019での仮締めを本締結",
"Mass 22.7g/mWidth 12.7mm/RSpan 232mm/R",
"ﾃﾝｼｮﾝ測定ﾎﾟｲﾝﾄ(ｾﾝﾀｰ部)"
]
} | {
"QualityItem": "ﾍﾞﾙﾄﾃﾝｼｮﾝ",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "50~70N",
"Method": "ﾍﾞﾙﾄ張力計",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"下から見た図",
"取付け方向に注意!この部品には方向性があります｡"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DOG取付",
"WorkItems": [
"1. にDOG をBOLT WASHER で取付ける",
"2. ｾﾝｻｰとDOG の位置関係を確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"下から見た図",
"ｾﾝｻｰ(ｸﾗﾝﾌﾟ原点)",
"ｾﾝｻｰ(ｸﾗﾝﾌﾟ下限)",
"ｾﾝｻｰとの干渉無き事",
"ｾﾝｻｰ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "APX検査機",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整1",
"WorkItems": [
"1. を㉖に接続する",
"2. ㉖の背面にある電源をONにする",
"3. 画面右上のPower ONﾎﾞﾀﾝと〇印のﾎﾞﾀﾝを同時に押す"
],
"WorkPoints": [
"治具",
"ﾓｰﾀｰ",
"ｾﾝｻ接続の線はDOGが動くので当たらないように止めておく",
"右上のPower ONが黄色にならないと検査機は動かない"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M607BKP",
"M607P",
"M60□BKR",
"M607R",
"ﾓｰﾀｰｺﾈｸﾀ接続",
"PH163",
"PH166",
"B080R",
"B720R",
"ｾﾝｻ接続"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "APX検査機",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整2",
"WorkItems": [
"1. ﾌﾟﾛｾｽﾁｬﾝﾊﾞｰ調整/検査のﾎﾞﾀﾝを押す",
"2. センサ確認画面がでるので クランプ昇降部のセンサが反応するか㉗で遮光し確認する",
"4. 下にﾀﾌﾞが出てくるので､左から3番目のMoterを押す",
"2. センサ確認画面がでるので クランプ昇降部のセンサが反応するか㉗で遮光し確認する",
"4. 下にﾀﾌﾞが出てくるので､左から3番目のMoterを押す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾗﾝﾌﾟ昇降 ORG PH163(B080)検出ONｸﾗﾝﾌﾟ下降位置 PH166(B072)検出ON",
"ｸﾗﾝﾌﾟ昇降 ORG PH163(B080)検出ONｸﾗﾝﾌﾟ下降位置 PH166(B072)検出ON"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "APX検査機",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整3",
"WorkItems": [
"2. 移動量を 41.3 に数値を設定する",
"1. 〇印の部分が有効になっていることを確認する",
"3. Originと画面外のﾎﾞﾀﾝを同時に押し､ｸﾗﾝﾌﾟ軸を原点復帰させる"
],
"WorkPoints": [
"無効になってる場合はﾎﾞﾀﾝを押して有効に切り替える",
"ｸﾗﾝﾌﾟ昇降が動く為､配線の挟み込みやぶつかりが無いかを確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"Origin 原点復帰JOG UP 押してる間だけ昇降部が上がるJOG Down 押している間だけ昇降部が下がるMOVE 移動量分だけ動く検査機のﾊﾟﾄﾗﾝﾌﾟ赤 ｴﾗｰ黄色 停止中緑 稼働中",
"検査機が動く場合は必ず押す"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整4",
"WorkItems": [
"2. 高さが出ていない場合は､PH163(原点ｾﾝｻ)の位置を動かして調整を行う",
"1. 原点のｼｬﾌﾄの高さを測る",
"3. JOG DownもしくはMOVEを押し､原点をずらしてから再度Originを押し原点復帰を行い､1の作業に戻る"
],
"WorkPoints": [
"PH163",
"位置調整ができた際､ｾﾝｻｰの中心にﾄﾞｸﾞが通っていることを確認する",
"高さ75.3㎜±0.1㎜",
"※高さが出ていたらこの作業は必要ない",
"※高さが出ていたらこの作業は必要ない"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"75.3㎜",
"検査表 :ﾁｬﾝﾊﾞｰ底面からの高さ",
"検査表 :ﾓｰﾀｰ原点位置ｾﾝｻ検出"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "75.3±0.1㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "APX検査機",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整4",
"WorkItems": [
"2. 高さが出ていない場合は､PH163(原点ｾﾝｻ)の位置を動かして調整を行う",
"1. 原点のｼｬﾌﾄの高さを測る",
"3. JOG DownもしくはMOVEを押し､原点をずらしてから再度Originを押し原点復帰を行い､1の作業に戻る"
],
"WorkPoints": [
"PH163",
"位置調整ができた際､ｾﾝｻｰの中心にﾄﾞｸﾞが通っていることを確認する",
"高さ75.3㎜±0.1㎜",
"※高さが出ていたらこの作業は必要ない",
"※高さが出ていたらこの作業は必要ない"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"75.3㎜",
"検査表 :ﾁｬﾝﾊﾞｰ底面からの高さ",
"検査表 :ﾓｰﾀｰ原点位置ｾﾝｻ検出"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整5",
"WorkItems": [
"2. 原点のｼｬﾌﾄの高さを測る",
"4. JOG UPもしくはOriginを押し､ 再度MOVEを押し下限位置にし､2の作業に戻る",
"3. 高さが出ていない場合は､PH166(下降)の位置を動かして調整を行う"
],
"WorkPoints": [
"高さ34.0㎜±0.1㎜",
"※高さが出ていたらこの作業は必要ない",
"どちらかでずらす",
"下限位置",
"※高さが出ていたらこの作業は必要ない"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"34.0㎜",
"検査表 :ﾁｬﾝﾊﾞｰ底面からの高さ",
"検査表 :ﾓｰﾀｰ下限位置ｾﾝｻ検出"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "34.0±0.1㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "APX検査機",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾘﾝｸﾞ昇降部原点調整5",
"WorkItems": [
"2. 原点のｼｬﾌﾄの高さを測る",
"4. JOG UPもしくはOriginを押し､ 再度MOVEを押し下限位置にし､2の作業に戻る",
"3. 高さが出ていない場合は､PH166(下降)の位置を動かして調整を行う",
"4. JOG UPもしくはOriginを押し､ 再度MOVEを押し下限位置にし､2の作業に戻る",
"3. 高さが出ていない場合は､PH166(下降)の位置を動かして調整を行う"
],
"WorkPoints": [
"高さ34.0㎜±0.1㎜",
"※高さが出ていたらこの作業は必要ない",
"どちらかでずらす",
"下限位置",
"※高さが出ていたらこの作業は必要ない",
"※高さが出ていたらこの作業は必要ない",
"どちらかでずらす",
"下限位置",
"※高さが出ていたらこの作業は必要ない"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"34.0㎜",
"検査表 :ﾁｬﾝﾊﾞｰ底面からの高さ",
"検査表 :ﾓｰﾀｰ下限位置ｾﾝｻ検出"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾈｼﾞ取付",
"WorkItems": [
"1. にBOLT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"ｸﾘｰﾝ工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "X軸真直確認治具",
"Size": "",
"ToolOther": "FM-2209",
"WorkName": "左側ｶﾞｲﾄﾞ組立1/3",
"WorkItems": [
"1. POST をCOLLAR に挿入する",
"2. 1.完成品をBRACKET に挿入しWASHER BOLT で取付ける"
],
"WorkPoints": [
"FM-2209",
"BRACKET の幅を㉖で広げる"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2209",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "左側ｶﾞｲﾄﾞ組立1/3",
"WorkItems": [
"1. POST をCOLLAR に挿入する",
"2. 1.完成品をBRACKET に挿入しWASHER BOLT で取付ける"
],
"WorkPoints": [
"FM-2209",
"BRACKET の幅を㉖で広げる"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "左側ｶﾞｲﾄﾞ組立2/3",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾌﾞﾛｯｸｹﾞｰｼﾞ5㎜を挟み取付けの事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "5㎜",
"ToolOther": "",
"WorkName": "左側ｶﾞｲﾄﾞ組立2/3",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾌﾞﾛｯｸｹﾞｰｼﾞ5㎜を挟み取付けの事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "定盤",
"Size": "",
"ToolOther": "",
"WorkName": "左側ｶﾞｲﾄﾞ組立2/3",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾌﾞﾛｯｸｹﾞｰｼﾞ5㎜を挟み取付けの事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "左側ｶﾞｲﾄﾞ組立2/3",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける",
"2. 1.完成品にCOVER を取付ける",
"3. にTAPE を貼付ける",
"2. 1.完成品にCOVER を取付ける",
"3. にTAPE を貼付ける"
],
"WorkPoints": [
"ﾌﾞﾛｯｸｹﾞｰｼﾞ5㎜を挟み取付けの事",
"端面40㎜から貼付け",
"表面の端面 6mmから貼付",
"端面40㎜から貼付け",
"表面の端面 6mmから貼付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各指示寸法±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "左側ｶﾞｲﾄﾞ組立3/3",
"WorkItems": [
"1. GUIDE へTAPE を貼付ける",
"2. 1.完成品を へBOLT WASHER で取付ける"
],
"WorkPoints": [
"右側ｴｯｼﾞ部から貼付けて気泡が入らない様貼付ける事",
"GUIDE の取付位置は長穴ｾﾝﾀｰで取付ける取付の際中央位置を仮固定し両ｻｲﾄﾞで確認し位置決めする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "左側ｶﾞｲﾄﾞ組立3/3",
"WorkItems": [
"1. GUIDE へTAPE を貼付ける",
"2. 1.完成品を へBOLT WASHER で取付ける"
],
"WorkPoints": [
"右側ｴｯｼﾞ部から貼付けて気泡が入らない様貼付ける事",
"GUIDE の取付位置は長穴ｾﾝﾀｰで取付ける取付の際中央位置を仮固定し両ｻｲﾄﾞで確認し位置決めする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付け確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "右側ｶﾞｲﾄﾞ組立1/2",
"WorkItems": [
"1. POST をCOLLAR に挿入する",
"2. 1.完成品をBRACKET に挿入しBOLT BOLT WASHER で取付ける"
],
"WorkPoints": [
"FM-2209"
],
"Tolks": [
"BOLT 締付ﾄﾙｸ 9.8N･m",
"BOLT 締付ﾄﾙｸ 10.9N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.