ayuzawa/ManageProcess19 · Datasets at Hugging Face

instruction stringlengths 222 1.92k	output stringlengths 193 312	category stringclasses 1 value	fileName null
{ "ToolName": "ﾍﾞﾙﾄ張力計", "Size": "", "ToolOther": "", "WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸駆動部組立③", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-087" ] }	{ "QualityItem": "ﾍﾞﾙﾄﾃﾝｼｮﾝ", "ToolManageNo": "-", "ToolCycle": "1回/年", "ToolRecord": "校正成績書", "StdVal": "ﾍﾞﾙﾄ張力200~220Hz(44±4N)", "Method": "ﾍﾞﾙﾄ張力計", "RecordMethod": "WWYJ-5300-087", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "原点出し治具", "Size": "", "ToolOther": "FM-3446", "WorkName": "X軸原点調整", "WorkItems": [ "1. の原点位置を調整しｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを増し締め", "2. 1.完成品の取り外していたｶｯﾌﾟﾘﾝｸﾞ部ｶﾊﾞｰ･ﾎﾞｰﾙﾈｼﾞ部ｶﾊﾞｰを取付" ], "WorkPoints": [ "㉖原点出し治具にてモーターの原点を調整(表示を00に調整)", "ｽｹｰﾙ目で原点位置に移動させて､ﾓｰﾀｰZ相位置にてｶｯﾌﾟﾘﾝｸﾞを固定｡" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "X軸原点位置", "821mm±0.5mm 原点確認", "検査表 :<X軸> ﾓｰﾀｰ原点調整", "821㎜", "ｶｯﾌﾟﾘﾝｸﾞ固定位置", "WWYJ-5300-087" ] }	{ "QualityItem": "原点確認", "ToolManageNo": "FM-3446", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "原点位置である事", "Method": "原点出し治具", "RecordMethod": "WWYJ-5300-087", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "1000㎜", "ToolOther": "", "WorkName": "X軸原点調整", "WorkItems": [ "1. の原点位置を調整しｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを増し締め", "2. 1.完成品の取り外していたｶｯﾌﾟﾘﾝｸﾞ部ｶﾊﾞｰ･ﾎﾞｰﾙﾈｼﾞ部ｶﾊﾞｰを取付" ], "WorkPoints": [ "㉖原点出し治具にてモーターの原点を調整(表示を00に調整)", "ｽｹｰﾙ目で原点位置に移動させて､ﾓｰﾀｰZ相位置にてｶｯﾌﾟﾘﾝｸﾞを固定｡" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "X軸原点位置", "821mm±0.5mm 原点確認", "検査表 :<X軸> ﾓｰﾀｰ原点調整", "821㎜", "ｶｯﾌﾟﾘﾝｸﾞ固定位置" ] }	{ "QualityItem": "原点確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "821㎜±0.5㎜原点確認", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "", "ToolOther": "", "WorkName": "配線用ﾌﾞﾗｹｯﾄ組立", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "4.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線用ﾌﾞﾗｹｯﾄ組立", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布ｺﾞﾏ粒:2", "Method": "目視", "RecordMethod": "-", "Other": "ﾛｯｸﾀｲﾄ243", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線用ﾌﾞﾗｹｯﾄ・ｶﾊﾞｰ取付", "WorkItems": [ "▲1. にSPACER をSCREW でADHESIVE ﾛｯｸﾀｲﾄを塗布して組付け", "▲2. 1.完成品にをBOLT WASHER でADHESIVE ﾛｯｸﾀｲﾄを塗布して組付け", "3. 2.完成品にCOVER をSCREW で組付け" ], "WorkPoints": [ "拡大図" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1.完成品", "2.完成品", "接着剤塗布ｺﾞﾏ粒:2", "接着剤塗布ｺﾞﾏ粒:2" ] }	{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布ｺﾞﾏ粒:2", "Method": "目視", "RecordMethod": "-", "Other": "ﾛｯｸﾀｲﾄ243", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "空圧部ﾄﾞｯｷﾝｸﾞ", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾄﾚｲｽﾃｰｼﾞ部ﾄﾞｯｷﾝｸﾞ", "WorkItems": [ "1. にをBOLT WASHER で組付け" ], "WorkPoints": [ "A断面図" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｴｱｰ供給治具", "Size": "", "ToolOther": "FM-2823", "WorkName": "ﾄﾚｲｽﾃｰｼﾞ高さ調整", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "FM-2823", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾊｲﾄｹﾞｰｼﾞ", "Size": "600㎜", "ToolOther": "", "WorkName": "ﾄﾚｲｽﾃｰｼﾞ高さ調整", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-089", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-089" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "①384.5㎜±0.1㎜", "Method": "ﾊｲﾄｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5300-089", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾊｲﾄｹﾞｰｼﾞ", "Size": "600㎜", "ToolOther": "", "WorkName": "ﾄﾚｲｽﾃｰｼﾞ高さ調整", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-089", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-089" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "②417.5㎜±0.1㎜", "Method": "ﾊｲﾄｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5300-089", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ﾊｲﾄｹﾞｰｼﾞ", "Size": "600㎜", "ToolOther": "", "WorkName": "ﾄﾚｲｽﾃｰｼﾞ高さ調整", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-089", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-089" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "③412.0㎜±0.1㎜", "Method": "ﾊｲﾄｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5300-089", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線配管引き回し①", "WorkItems": [ "1. にLABEL TERMINAL PROCESS LABEL TERMINAL PROCESS のﾀｸﾞをを取付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ITVEM4111P", "E0501R", "ITVMM4111P", "ITYEM4110P", "ITXEM4109P", "ITYMM4110P", "ITXMM4109P" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線配管引き回し②", "WorkItems": [ "1. にCABLE CABLE CABLE の配線を取付" ], "WorkPoints": [ "拡大図" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ITVME4111R", "E0501P", "ITVMM4111R", "ITVME4111P", "E0501R", "ITVMM4111P", "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "ｲﾝｼｭﾛｯｸ(100mm)", "ｲﾝｼｭﾛｯｸ(300mm)", "接続確認", "検査表 :接続確認 (3)ICﾄﾚｲｽﾃｰｼﾞ部(正流れｽﾃｰｼﾞ)", "WWYJ-5300-115" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "WWYJ-5300-115", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線配管引き回し③", "WorkItems": [ "1. にCABLE CABLE の配線を取付" ], "WorkPoints": [ "ﾍﾞﾙﾄの下を通す", "A断面図", "B矢視図(ﾄﾚｲｽﾃｰｼﾞ下(Y軸部))" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :接続確認 (4)ICﾄﾚｲｽﾃｰｼﾞ部(正流れｽﾃｰｼﾞD1500)", "1B11010R", "1B11020R", "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "ｲﾝｼｭﾛｯｸ(100mm)", "B11015R", "接続確認", "検査表 :接続確認 (2)ICﾄﾚｲｽﾃｰｼﾞ部(ITY軸)", "接続確認", "WWYJ-5300-115" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "WWYJ-5300-115", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線配管引き回し④", "WorkItems": [ "1. にTUBE の配管を㉖で長さを調整し接続" ], "WorkPoints": [ "A矢視図", "L側配管を接続後､R側配管を接続し支柱にｲﾝｼｭﾛｯｸで固定", "支柱の内側へ", "B矢視図", "支柱の内側へ", "C断面図", "D断面図", "⑥の反対の端にﾏｽｷﾝｸﾞﾃｰﾌﾟで配管接続番号が判る様に明記の事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "L1", "L2", "R2", "R1", "L1", "L2", "R2", "R1", "下段Down", "下段Up", "上段Down", "上段Up", "下段Down", "下段Up", "上段Down", "上段Up", "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "ｲﾝｼｭﾛｯｸ(150mm)" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "", "ToolOther": "", "WorkName": "配線配管引き回し⑤", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線配管引き回し⑥", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-115", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-115" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "WWYJ-5300-115", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線配管引き回し⑦", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "配線配管引き回し⑧", "WorkItems": [ "1. にTUBE ･TUBE の配管をｶｯﾄして接続" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "φ4黒 130mm", "φ6橙 70mm", "φ6橙 110mm" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "配線配管引き回し⑨", "WorkItems": [ "1. にXｽﾃｰｼﾞからの配管をｶｯﾄして接続" ], "WorkPoints": [ "φ4黒配管接続図", "φ4黒 6芯ﾁｭｰﾌﾞ", "A矢視図(ﾄﾚｲ吸着)", "B矢視図(ﾄﾚｲｽﾃｰｼﾞ上下)" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ(100mm)", "ｲﾝｼｭﾛｯｸ(200mm)", "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線配管引き回し⑩", "WorkItems": [ "1. にCABLE CABLE CABLE の配線を接続" ], "WorkPoints": [ "接続確認" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :接続確認 (1)ICﾄﾚｲｽﾃｰｼﾞ部(ITX軸ｾﾝｻｰ､ﾊﾞﾙﾌﾞ)", "整線時はX軸ﾄﾞｸﾞとの干渉に注意", "ｲﾝｼｭﾛｯｸ(100mm)", "B10944R", "R31034R", "R31035R", "R31036R", "R31037R", "G2A020", "G2A021", "R31044R", "R31045R", "R31046R", "R31047R", "R31031R", "R31032R", "R31033R", "R31041R", "R31042R", "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "WWYJ-5300-115" ] }	{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "WWYJ-5300-115", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｺﾝﾍﾞｯｸｽ", "Size": "3m", "ToolOther": "", "WorkName": "配線配管引き回し⑪", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±1㎜", "Method": "ｺﾝﾍﾞｯｸｽ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "引き渡し準備", "WorkItems": [ "1. ･COVER ･COVER ･SCREW ･CLAMPER ･SPACER ･BOLT ･WASHER ･BOLT ･BOLT ･WASHER ･WASHER を本体載せ込み工程に引き渡す" ], "WorkPoints": [ "ｶﾊﾞｰの取付は本体載せ込み完了後に実施の事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "引き渡し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き渡し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾄﾚｲｽﾃｰｼﾞ組立①", "WorkItems": [ "2. PLATE ･PLATE にPAD を取付け", "1. PLATE ･PLATE のｴｱｰ経路が指示通り通っていることを確認する", "3. 2.完成品にBRACKET ･BRACKET をSCREW で組付け" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業ではそれぞれ2個作成", "この作業ではそれぞれ2個作成", "組付け詳細" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾄﾚｲｽﾃｰｼﾞ組立②", "WorkItems": [ "1. ･にBRACKET をBOLT ･WASHER で組付け", "2. 1.完成品にJOINT を組付け" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業ではそれぞれ2個作成", "この作業ではそれぞれ2個作成" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾄﾚｲｽﾃｰｼﾞ組立③", "WorkItems": [ "1. TUBE を指定の長さでｶｯﾄ", "2. ･に1.完成品を組付け" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業ではそれぞれ2個作成", "TUBE φ4白 100㎜ 4本" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法:100㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ICﾄﾚｲｽﾃｰｼﾞ部へ引き渡し", "WorkItems": [ "1. ･･BOLT ･WASHER を引き渡す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "ﾌﾚｰﾑ1", "WorkItems": [ "1. BLOCK FRAME FRAME をNUT NUT BOLT BOLT で取付" ], "WorkPoints": [ "寸法通り取付けるBLOCK FRAME FRAME の合わせ面に隙間が無い事", "2ｾｯﾄ製作" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "271㎜", "119㎜", "119㎜" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌﾚｰﾑ2", "WorkItems": [ "1. にPLATE をPLATE で挟んでBOLT WASHER で取付", "1. にPLATE をPLATE で挟んでBOLT WASHER で取付" ], "WorkPoints": [ "左ﾊﾝﾄﾞ組立", "右ﾊﾝﾄﾞ組立" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "", "ToolOther": "1/100", "WorkName": "ﾌﾚｰﾑ3", "WorkItems": [ "1. を定盤上でN015ﾌﾚｰﾑ上面の高さを測定する" ], "WorkPoints": [ "2ﾋﾟｰｽ測定", "0.4㎜以内", "P002の下面と定盤に隙間が無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :P(2軸)3 ｱﾙﾑﾌﾚｰﾑ高さ測定", "A001", "P005､P006", "P004", "N015", "P003", "定盤", "1~4相互の高低差を確認", "WWYJ-5300-46" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "高低差0.4㎜以内", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5300-46", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "左ﾌﾚｰﾑ", "WorkItems": [ "1. FRAME にBRACKET をNUT BOLT WASHER で取付", "2. 1.完成品にJOINT をBOLT WASHER WASHER で取付", "3. 2.完成品にCABLE-SUPPORT を取付", "4. 3.完成品にNUT を入れる", "1. FRAME にBRACKET をNUT BOLT WASHER で取付", "2. 1.完成品にJOINT をBOLT WASHER WASHER で取付", "3. 2.完成品にCABLE-SUPPORT を取付", "4. 3.完成品にNUT を入れる" ], "WorkPoints": [ "FRAME は方向あり", "FRAME の裏面に8個入れる", "FRAME の表面に2個入れる位置は不問", "FRAME の裏面に4個入れる位置は不問", "FRAME の測面に2個入れる位置は不問", "FRAME の表面に2個入れる位置は不問", "FRAME は方向あり", "FRAME の裏面に8個入れる", "FRAME の表面に2個入れる位置は不問", "FRAME の裏面に4個入れる位置は不問", "FRAME の測面に2個入れる位置は不問", "FRAME の表面に2個入れる位置は不問" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "230㎜", "166.3㎜", "45㎜", "15㎜", "28㎜", "120㎜", "230㎜", "166.3㎜", "45㎜", "15㎜", "28㎜", "120㎜" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "右ﾌﾚｰﾑ", "WorkItems": [ "1. FRAME にBRACKET をNUT BOLT WASHER で取付", "2. 1.完成品にJOINT をBOLT WASHER WASHER で取付", "3. 2.完成品にCABLE-SUPPORT を取付", "4. 3.完成品にNUT を入れる", "1. FRAME にBRACKET をNUT BOLT WASHER で取付", "2. 1.完成品にJOINT をBOLT WASHER WASHER で取付", "3. 2.完成品にCABLE-SUPPORT を取付", "4. 3.完成品にNUT を入れる" ], "WorkPoints": [ "FRAME は方向あり", "FRAME の裏面に8個入れる", "FRAME の測面に2個入れる位置は不問", "FRAME の表面に2個入れる位置は不問", "FRAME の裏面に4個入れる位置は不問", "FRAME の表面に2個入れる位置は不問", "FRAME は方向あり", "FRAME の裏面に8個入れる", "FRAME の測面に2個入れる位置は不問", "FRAME の表面に2個入れる位置は不問", "FRAME の裏面に4個入れる位置は不問", "FRAME の表面に2個入れる位置は不問" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "銘板貼付け1", "WorkItems": [ "1. にLABEL を貼付け" ], "WorkPoints": [ "2ｾｯﾄ製作" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾒﾓﾘとの合わせ基準", "ﾒﾓﾘとの合わせ基準" ] }	{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法の位置に貼付けている事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "銘板貼付け2", "WorkItems": [ "1. にLABEL を貼付け" ], "WorkPoints": [ "この範囲の貼付け寸法を明示右側も同じ", "2ｾｯﾄ製作" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "2㎜", "5㎜", "80㎜", "5㎜", "5㎜", "230㎜", "5㎜", "5㎜", "5㎜", "2㎜", "80㎜", "230㎜" ] }	{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法の位置に貼付けている事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "銘板貼付け3", "WorkItems": [ "1. BRACKET にLABEL を貼付け", "3. BRACKET にLABEL を貼付け", "4. 3.完成品にCABLE-SUPPORT を取付ける", "2. 1.完成品にCABLE-SUPPORT を取付ける" ], "WorkPoints": [ "左ﾊﾝﾄﾞ用", "右ﾊﾝﾄﾞ用" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "23㎜", "155㎜", "155㎜", "23㎜" ] }	{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法の位置に貼付けている事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "銘板貼付け4", "WorkItems": [ "1. COVER にLABEL を貼付け", "3. COVER にLABEL を貼付け", "4. 3.完成品にCABLE-SUPPORT を取付ける", "2. 1.完成品にCABLE-SUPPORT を取付ける" ], "WorkPoints": [ "注) AMPP構成時", "注) AMP構成時はこちらを貼る", "左ﾊﾝﾄﾞ用", "右ﾊﾝﾄﾞ用" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "32㎜", "2㎜", "32㎜", "2㎜" ] }	{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法の位置に貼付けている事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾊﾝﾄﾞﾊﾞﾙﾌﾞ1", "WorkItems": [ "1. JOINT SPACER JOINT を取付" ], "WorkPoints": [ "16ｾｯﾄ製作" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "", "ToolOther": "", "WorkName": "ﾊﾝﾄﾞﾊﾞﾙﾌﾞ2", "WorkItems": [ "1. にJOINT を取付(4か所)", "2. 1.完成品にVALVE をBOLT WASHER WASHER で取付(12か所)", "1. 2｡完成品のJOINT VALVE にを取付(16か所)" ], "WorkPoints": [ "VALVE は方向あり", "左ﾊﾝﾄﾞ用", "右ﾊﾝﾄﾞ用", "矢印方向に取付" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "10㎜", "10㎜" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法:10.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "治具", "Size": "", "ToolOther": "FM-6046", "WorkName": "搬送PAD組立①", "WorkItems": [ "1. BLOCK にVACUUM-PAD を仮取付(ﾅｯﾄはVACUUM-PAD の付属品を使用)", "3. PAD高さ調整を行う｡", "2. 1.完成品を㉗搬送PAD高さ合わせジグに取付" ], "WorkPoints": [ "32ｾｯﾄ製作" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-46" ] }	{ "QualityItem": "隙間確認", "ToolManageNo": "FM-6046", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "29.8±0.1㎜(隙間0.1㎜以内)", "Method": "治具", "RecordMethod": "WWYJ-5300-46", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "", "ToolOther": "", "WorkName": "搬送PAD組立①", "WorkItems": [ "1. BLOCK にVACUUM-PAD を仮取付(ﾅｯﾄはVACUUM-PAD の付属品を使用)", "3. PAD高さ調整を行う｡", "2. 1.完成品を㉗搬送PAD高さ合わせジグに取付" ], "WorkPoints": [ "32ｾｯﾄ製作" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-46" ] }	{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "29.8±0.1㎜(隙間0.1㎜以内)", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5300-46", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "搬送PAD組立②", "WorkItems": [ "▲1. にの付属品をADHESIVE ﾈｼﾞﾛｯｸ材で取付", "▲2. 1.完成品上部の付属品のﾌﾟﾗｸﾞを取り外し､JOINT をADHESIVE ﾈｼﾞﾛｯｸ材で取付ｼﾞｮｲﾝﾄの向き注意" ], "WorkPoints": [ "吸着穴に接着剤が混入し無い事", "吸着穴に接着剤が混入し無い事", "4ｾｯﾄ製作", "8ｾｯﾄ製作", "4ｾｯﾄ製作", "下部ｼﾞｮｲﾝﾄと上部ｼﾞｮｲﾝﾄの向き違いがある3種類製作する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :AM2､ねじﾛｯｸ塗布", "検査表 :AM2､ねじﾛｯｸ塗布", "接着剤塗布ｺﾞﾏ粒:2", "接着剤塗布ｺﾞﾏ粒:2", "ADHESIVE ねじﾛｯｸ塗布", " の付属品(ADHESIVE ねじﾛｯｸ塗布)", "WWYJ-5300-46" ] }	{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布ｺﾞﾏ粒:2", "Method": "目視", "RecordMethod": "WWYJ-5300-46", "Other": "ﾛｯｸﾀｲﾄ243", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "搬送PAD組立③", "WorkItems": [ "▲1. にの付属品をADHESIVE ﾈｼﾞﾛｯｸ材で取付" ], "WorkPoints": [ "吸着穴に接着剤が混入し無い事", "16ｾｯﾄ製作" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :AM2､ねじﾛｯｸ塗布", "接着剤塗布ｺﾞﾏ粒:2", " の付属品(ADHESIVE ねじﾛｯｸ塗布)", " の付属品(ADHESIVE ねじﾛｯｸ塗布)", "WWYJ-5300-46" ] }	{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布ｺﾞﾏ粒:2", "Method": "目視", "RecordMethod": "WWYJ-5300-46", "Other": "ﾛｯｸﾀｲﾄ243", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "左吸着ﾊﾝﾄﾞ組立1", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "210㎜" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法:210.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "左吸着ﾊﾝﾄﾞ組立2", "WorkItems": [ "1. をにNUT BOLT WASHER で取付" ], "WorkPoints": [ "端面合わせ" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "左吸着ﾊﾝﾄﾞ組立3", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "5㎜", "110㎜", "110㎜", "40㎜", "40㎜", "40㎜", "40㎜", "110㎜", "5㎜", "110㎜" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "左吸着ﾊﾝﾄﾞ組立4", "WorkItems": [ "1. にTUBE TUBE TUBE TUBE TUBE を取付", "2. 各配管を㉘で固定" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "左吸着ﾊﾝﾄﾞ組立5", "WorkItems": [ "▲1. CAP CAP に㉖を塗布しに取付" ], "WorkPoints": [ "CAP の中央部2本の爪は㉘で切断する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :(P2軸)2,接着剤塗布", "接着剤塗布小豆:2", "WWYJ-5300-46" ] }	{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布小豆:2", "Method": "目視", "RecordMethod": "WWYJ-5300-46", "Other": "ﾛｯｸﾀｲﾄ415", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "右吸着ﾊﾝﾄﾞ組立1", "WorkItems": [ "1. にをNUT BOLT WASHER で仮付け", "2. BRACKET BRACKET をNUT WASHER BOLT WASHER で仮付け", "3. 取付位置を210㎜に合わせ､各部品を隙間なく取付ける(本締め)" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法:210.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "右吸着ﾊﾝﾄﾞ組立2", "WorkItems": [ "1. をにNUT BOLT WASHER で取付" ], "WorkPoints": [ "端面合わせ" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "右吸着ﾊﾝﾄﾞ組立3", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "5㎜", "110㎜", "110㎜", "40㎜", "40㎜", "40㎜", "40㎜", "110㎜", "5㎜", "110㎜" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "", "ToolOther": "", "WorkName": "右吸着ﾊﾝﾄﾞ組立4", "WorkItems": [ "1. にTUBE TUBE TUBE TUBE TUBE を取付", "2. 各配管を㉘で固定" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "右吸着ﾊﾝﾄﾞ組立5", "WorkItems": [ "▲1. CAP CAP にADHESIVE を塗布しに取付" ], "WorkPoints": [ "CAP の中央部2本の爪は㉘で切断する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :(P2軸)2､接着剤塗布", "接着剤塗布小豆:2", "WWYJ-5300-46" ] }	{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布小豆:2", "Method": "目視", "RecordMethod": "WWYJ-5300-46", "Other": "ﾛｯｸﾀｲﾄ415", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "次工程へ引き渡し", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1. BOLT BOLT WASHER WASHER BOLT WASHER を次工程へ｡" ] }	{ "QualityItem": "引き渡し部材確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "正しい部材が引き渡される事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｾﾝﾀﾘﾝｸﾞﾌﾞﾛｯｸ取付", "WorkItems": [ "1. の取付用ﾎﾞﾙﾄ､ﾜｯｼｬを使ってBLOCK を取付" ], "WorkPoints": [ "PINに当付け" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾒﾝﾃﾅﾝｽﾗｲﾄP組立", "WorkItems": [ "SFN-SA4 4個", "SFA-9A2 4個", "六角穴付きﾎﾞﾙﾄM4×10 4本平座金みがき丸 4 4個", "1. BRACKET にLED-LAMP-UNIT をBOLT WASHER WASHER で取付ける", "2. 1の完成品にLABEL TERMINAL PROCESS を取付ける", "3. 2の完成品とNUT SUPPORT BOLT WASHER を付属する" ], "WorkPoints": [ "合わせる", "ﾗﾍﾞﾙ2種類" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "E0131R", "E0131R", "E0231R", "この作業ではﾗﾍﾞﾙ違いを2個製作" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6481", "WorkName": "ﾏｸﾞﾈｯﾄ取付け", "WorkItems": [ "1. ﾊｰﾈｽﾎﾞｰﾄﾞにﾏｸﾞﾈｯﾄを取付ける" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "⇒ﾏｸﾞﾈｯﾄ中", "⇒ﾏｸﾞﾈｯﾄ大" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "FM-6481", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾊｰﾈｽ準備", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1.下記ﾘｽﾄの順番でｹｰﾌﾞﾙを準備する" ] }	{ "QualityItem": "ｹｰﾌﾞﾙの準備", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り準備する事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6481", "WorkName": "ﾊｰﾈｽ引き回1", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "CN8K011", "R31140RR31141R", "1. CABLE を引き回す" ] }	{ "QualityItem": "配線確認", "ToolManageNo": "FM-6481", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り配線されている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6481", "WorkName": "ﾊｰﾈｽ引き回2", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1G10340-1R", "G10340P", "1. CABLE を引き回す" ] }	{ "QualityItem": "配線確認", "ToolManageNo": "FM-6481", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り配線されている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6481", "WorkName": "ﾊｰﾈｽ引き回3", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1G10340-2R", "G10341P", "1. CABLE を引き回す" ] }	{ "QualityItem": "配線確認", "ToolManageNo": "FM-6481", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り配線されている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6481", "WorkName": "ﾊｰﾈｽ引き回4", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1G10340-3R", "G10342P", "1. CABLE を引き回す" ] }	{ "QualityItem": "配線確認", "ToolManageNo": "FM-6481", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り配線されている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6481", "WorkName": "ﾊｰﾈｽ引き回5", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1G10340-4R", "G10343P", "1. CABLE を引き回す" ] }	{ "QualityItem": "配線確認", "ToolManageNo": "FM-6481", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り配線されている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6481", "WorkName": "ﾊｰﾈｽ引き回6", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1G10340-5R", "G10344P", "1. CABLE を引き回す" ] }	{ "QualityItem": "配線確認", "ToolManageNo": "FM-6481", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り配線されている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6481", "WorkName": "ﾊｰﾈｽ引き回7", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1G10340-6R", "G10345P", "1. CABLE を引き回す" ] }	{ "QualityItem": "配線確認", "ToolManageNo": "FM-6481", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り配線されている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6481", "WorkName": "ﾊｰﾈｽ引き回8", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ADPW-05ADPW-15", "CN1K6001", "1. CABLE を引き回す" ] }	{ "QualityItem": "配線確認", "ToolManageNo": "FM-6481", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り配線されている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6481", "WorkName": "ﾊｰﾈｽ引き回9", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "CN10K003", "BX2112", "1G10330R", "1G10340R", "1. CABLE を引き回す" ] }	{ "QualityItem": "配線確認", "ToolManageNo": "FM-6481", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り配線されている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6481", "WorkName": "ﾊｰﾈｽ引き回10", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "C-X2112", "PLED1P", "1. CABLE を引き回す", "1X012" ] }	{ "QualityItem": "配線確認", "ToolManageNo": "FM-6481", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り配線されている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6481", "WorkName": "ｲﾝｼｭﾛｯｸ固定", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1. ｲﾝｼｭﾛｯｸで固定する", "⇒100mm", "⇒150mm", "⇒200mm", "⇒250mm" ] }	{ "QualityItem": "取付確認", "ToolManageNo": "FM-6481", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "11.5N･m", "WorkName": "ﾌﾚｰﾑ組立①", "WorkItems": [ "1. FRAME-KIT(L) にFRAME-KIT(REAR) をBOLT ･WASHER で取付" ], "WorkPoints": [ "取付は仮固定※4面体にするまで､ﾎﾞﾙﾄの本締めはしない", "【注意】 WASHER 歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側" ], "Tolks": [ "締付ﾄﾙｸ 11.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "×3" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "11.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "11.5N･m", "WorkName": "ﾌﾚｰﾑ組立②", "WorkItems": [ "1. にFRAME-KIT(R) をBOLT WASHER で取付" ], "WorkPoints": [ "取付は仮固定※4面体にするまで､ﾎﾞﾙﾄの本締めはしない", "【注意】 WASHER 歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "×2" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "11.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "150cN･m", "WorkName": "ﾌﾚｰﾑ組立③", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "11.5N･m", "WorkName": "ﾌﾚｰﾑ組立③", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "11.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｺﾝﾍﾞｯｸｽ", "Size": "3.5m", "ToolOther": "", "WorkName": "ﾌﾚｰﾑ組立④", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±1㎜", "Method": "ｺﾝﾍﾞｯｸｽ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "11.5N･m", "WorkName": "ﾌﾚｰﾑ組立④", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "11.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "11.5N･m", "WorkName": "ﾌﾚｰﾑ組立⑤", "WorkItems": [ "1. にをBOLT WASHER BOLT BRACKET で取付" ], "WorkPoints": [ "下面にBOLT ･⑩で取付( と WASHER BRACKET の隙間無い事)", "【注意】 ③歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側", "【注意】下記取付け寸法は標準HEPA仕様の場合です", "前側のﾌﾚｰﾑと左右ﾌﾚｰﾑ､及びは､各面の段差が無いように調整し､ﾎﾞﾙﾄを締結する" ], "Tolks": [ "締付ﾄﾙｸ11.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "×20", "×4", "×16" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "11.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｺﾝﾍﾞｯｸｽ", "Size": "3.5m", "ToolOther": "", "WorkName": "ﾌﾚｰﾑ組立⑥", "WorkItems": [ "1. にFRAME-KIT(UPPER4) をBOLT WASHER で取付" ], "WorkPoints": [ "下面図", "【注意】 WASHER 歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側", " とFRAME-KIT(UPPER4) は､各面の段差が無いように調整し､ﾎﾞﾙﾄを締結する", "上面拡大図" ], "Tolks": [ "締付ﾄﾙｸ11.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "×4", "×4" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "1725±1㎜", "Method": "ｺﾝﾍﾞｯｸｽ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "11.5N･m", "WorkName": "ﾌﾚｰﾑ組立⑥", "WorkItems": [ "1. にFRAME-KIT(UPPER4) をBOLT WASHER で取付" ], "WorkPoints": [ "下面図", "【注意】 WASHER 歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側", " とFRAME-KIT(UPPER4) は､各面の段差が無いように調整し､ﾎﾞﾙﾄを締結する", "上面拡大図" ], "Tolks": [ "締付ﾄﾙｸ11.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "×4", "×4" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "11.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "600㎜", "ToolOther": "", "WorkName": "ﾌﾚｰﾑ組立⑦", "WorkItems": [ "1. FRAME-KIT(FRONT) (L) FRAME-KIT(FRONT) (R) にBRACKET BRACKET をWASHER BOLT WASHER ㉓で取付", "2. に1.完成品-1・-2をWASHER BOLT ⑧㉓で取付" ], "WorkPoints": [ "【注意】 FRAME-KIT(FRONT) (R) WASHER WASHER 歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側", "端面を合わせる" ], "Tolks": [ "締付ﾄﾙｸ11.5N･m", "締付ﾄﾙｸ11.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法:320㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "11.5N･m", "WorkName": "ﾌﾚｰﾑ組立⑦", "WorkItems": [ "1. FRAME-KIT(FRONT) (L) FRAME-KIT(FRONT) (R) にBRACKET BRACKET をWASHER BOLT WASHER ㉓で取付", "2. に1.完成品-1・-2をWASHER BOLT ⑧㉓で取付", "1. FRAME-KIT(FRONT) (L) FRAME-KIT(FRONT) (R) にBRACKET BRACKET をWASHER BOLT WASHER ㉓で取付", "2. に1.完成品-1・-2をWASHER BOLT ⑧㉓で取付" ], "WorkPoints": [ "【注意】 FRAME-KIT(FRONT) (R) WASHER WASHER 歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側", "端面を合わせる", "【注意】 FRAME-KIT(FRONT) (R) WASHER WASHER 歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側", "端面を合わせる" ], "Tolks": [ "締付ﾄﾙｸ11.5N･m", "締付ﾄﾙｸ11.5N･m", "締付ﾄﾙｸ11.5N･m", "締付ﾄﾙｸ11.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "11.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "11.5N･m", "WorkName": "ﾌﾚｰﾑ組立⑧", "WorkItems": [ "1. にFRAME-KIT(FRONT) (C) をBOLT WASHER で取付", "2. 裏側より､WASHER BOLT で取付" ], "WorkPoints": [ "内面図", "【注意】 WASHER 歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側", "取付は仮固定※ﾎﾞﾙﾄの本締めはしない", "取付は仮固定※ﾎﾞﾙﾄの本締めはしない" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "×6", "×4" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "11.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｺﾝﾍﾞｯｸｽ", "Size": "3.5m", "ToolOther": "", "WorkName": "ﾌﾚｰﾑ組立⑨", "WorkItems": [ "1. にFRAME-KIT(FRONT) をBOLT WASHER で取付", "2. ﾌﾚｰﾑ【FL､FR､C､F】連結ﾎﾞﾙﾄを本締めする" ], "WorkPoints": [ "【注意】 WASHER 歯付きﾜｯｼｬの歯の向きをｱﾙﾐﾌﾚｰﾑ側にする事 ※断面形状の鋭利な方が歯側", "取付は仮固定※ﾎﾞﾙﾄの本締めはしない", "ﾌﾚｰﾑ【F】", "ﾌﾚｰﾑ【F】", "ﾌﾚｰﾑ【C】", "ﾌﾚｰﾑ【FL】", "ﾌﾚｰﾑ【FR】", "各ﾌﾚｰﾑの段差が無いように調整し締結する" ], "Tolks": [ "締付ﾄﾙｸ11.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "170mm", "1518mm", "170mm", "765mm", "765mm", "1518mm" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±1㎜", "Method": "ｺﾝﾍﾞｯｸｽ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "11.5N･m", "WorkName": "ﾌﾚｰﾑ組立⑨", "WorkItems": [], "WorkPoints": [ "各ﾌﾚｰﾑの段差が無いように調整し締結する" ], "Tolks": [ "締付ﾄﾙｸ11.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "765mm", "1518mm" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "11.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "FRONT_戸当たりｺﾞﾑ取付", "WorkItems": [ "1. 前面に指定寸法にてRUBBER-LEG ･SPACER をBOLT で取付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "5mm", "5mm", "×8" ] }	{ "QualityItem": "外観確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ｷｽﾞ無い事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "FRONT_戸当たりｺﾞﾑ取付", "WorkItems": [ "1. 前面に指定寸法にてRUBBER-LEG ･SPACER をBOLT で取付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "5mm", "5mm", "×8" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法:5.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "600㎜", "ToolOther": "", "WorkName": "FRONT_ﾄﾞｱﾋﾝｼﾞ取付", "WorkItems": [ "1. 前面に指定寸法にてHINGE HINGE をSCREW で取付" ], "WorkPoints": [ "A内面", "B内面", "C内面", "D内面" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "153mm", "×8", "40mm", "535mm", "5mm" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±1㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "600㎜", "ToolOther": "", "WorkName": "REAR_戸当たりｺﾞﾑ・ﾄﾞｱﾋﾝｼﾞ取付", "WorkItems": [ "1. 背面に指定寸法にてRUBBER-LEG ･HINGE ･SCREW をBOLT ･⑨で取付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "153mm", "40mm", "560mm", "5mm", "5mm", "5mm" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法:5.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "600㎜", "ToolOther": "", "WorkName": "FRONT_ﾄﾞｱﾛｯｸ・ｾﾝｻｰ取付", "WorkItems": [ "1. に指定寸法にてをBOLT WASHER で取付" ], "WorkPoints": [ " 中央の取付ﾎﾞﾙﾄが､ﾌﾚｰﾑのｾﾝﾀｰになる様に下面から取付", "右略図､緑色部分のﾌﾚｰﾑ下面に取付(A･M用有注意)", "左下面", "必要部分のみ描いています", "右下面" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "6.M用", "6.A用", "759㎜", "759㎜", "759㎜", "759㎜" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法759各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "1000㎜", "ToolOther": "", "WorkName": "FRONT_下側ﾄﾞｱﾛｯｸ取付", "WorkItems": [ "1. に指定寸法にてをBOLT BOLT ㉒で取付" ], "WorkPoints": [ "必要部分のみ描いています(内面図)", "右略図､緑色部分のﾌﾚｰﾑ下面･内面に取付", "FRONT", "FRONT 左右共" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "←ﾌﾚｰﾑ端面から 730㎜", "730㎜ﾌﾚｰﾑ端面から→", "707㎜ﾌﾚｰﾑ端面から→", "←707㎜ﾌﾚｰﾑ端面から", "1B10110-3R", "1B10110-4R", "1B10C20-3R", "1B10C20-4R", "開閉ｶﾊﾞｰ左(A･ACF)", "開閉ｶﾊﾞｰ右(M･仮圧着)" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "REAR_ﾄﾞｱﾛｯｸ・ｾﾝｻｰ取付", "WorkItems": [ "1. に指定寸法にてをBOLT WASHER ㉒BOLT BOLT で取付" ], "WorkPoints": [ "必要部分のみ描いています(内面図)", "ｺﾞﾑは外向きに取付", "端面をそろえる事", "右略図､緑色部分のﾌﾚｰﾑ内面･側面に取付", "REAR" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "24mm", "←ﾌﾚｰﾑ端面から 730㎜", "21.2㎜", "21.2㎜", "24mm", "REAR 外側", "387.5mm", "415.5mm", "3㎜", "37㎜", "4.2㎜", "150mm", "120mm" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "1000㎜", "ToolOther": "", "WorkName": "非常停止ｽｲｯﾁ取付", "WorkItems": [ "1. に指定寸法にてをBOLT WASHER で取付" ], "WorkPoints": [ "必要部分のみ描いています", "前後位置は非常停止ﾌﾞﾗｹｯﾄとﾌﾚｰﾑ端面を合わす", "右略図､緑色部分のﾌﾚｰﾑ上面に取付", "FRONT", "REAR", "FRONT 左右共", "REAR" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "719㎜", "719㎜", "267.5㎜", "277.5㎜", "×2" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±1㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "REAR_CIM配線ｶﾊﾞｰ取付", "WorkItems": [ "1. に指定寸法にてをBOLT WASHER BOLT WASHER で取付" ], "WorkPoints": [ "必要部分のみ描いています", "前後位置はｶﾊﾞｰとﾌﾚｰﾑ端面を合わす", "右略図､緑色部分のﾌﾚｰﾑ上面に取付", "REAR", "REAR 外面", "A断面拡大図", " 取付に仕様あり※標準仕様は略図のとおり※CIMﾓﾆﾀｰ仕様ではの向きが180°逆になる", "取付ﾎﾞﾙﾄ類BOLT WASHER BOLT WASHER は同梱品を使用" ], "Tolks": [ "締付ﾄﾙｸ11.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "95㎜", "710㎜" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法:95.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "REAR_CIM配線ｶﾊﾞｰ取付", "WorkItems": [ "1. に指定寸法にてをBOLT WASHER BOLT WASHER で取付" ], "WorkPoints": [ "必要部分のみ描いています", "前後位置はｶﾊﾞｰとﾌﾚｰﾑ端面を合わす", "右略図､緑色部分のﾌﾚｰﾑ上面に取付", "REAR", "REAR 外面", "A断面拡大図", " 取付に仕様あり※標準仕様は略図のとおり※CIMﾓﾆﾀｰ仕様ではの向きが180°逆になる", "取付ﾎﾞﾙﾄ類BOLT WASHER BOLT WASHER は同梱品を使用" ], "Tolks": [ "締付ﾄﾙｸ11.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "95㎜", "710㎜" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法710±1㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "11.5N･m", "WorkName": "REAR_CIM配線ｶﾊﾞｰ取付", "WorkItems": [ "1. に指定寸法にてをBOLT WASHER BOLT WASHER で取付" ], "WorkPoints": [ "必要部分のみ描いています", "前後位置はｶﾊﾞｰとﾌﾚｰﾑ端面を合わす", "右略図､緑色部分のﾌﾚｰﾑ上面に取付", "REAR", "REAR 外面", "A断面拡大図", " 取付に仕様あり※標準仕様は略図のとおり※CIMﾓﾆﾀｰ仕様ではの向きが180°逆になる", "取付ﾎﾞﾙﾄ類BOLT WASHER BOLT WASHER は同梱品を使用" ], "Tolks": [ "締付ﾄﾙｸ11.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "95㎜", "710㎜" ] }	{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "11.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "FRONT_SDﾘｰﾀﾞｰ取付", "WorkItems": [ "1. に指定寸法にてをBOLT ･WASHER で取付" ], "WorkPoints": [ "必要部分のみ描いています", "右略図､緑色部分のﾌﾚｰﾑ内面に取付", "FRONT", "内面", "外面", "前面", "取付ﾎﾞﾙﾄ類BOLT ･WASHER は同梱品を使用" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "73mm", "24mm" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "FRONT_ｱｰｽ端子取付", "WorkItems": [ "1. に指定寸法にてTERMINAL をBOLT WASHER WASHER で取付" ], "WorkPoints": [ "必要部分のみ描いています", "右略図､緑色部分のﾌﾚｰﾑ内面に取付", "FRONT", "内面", "外面", "前面", "前後位置はｱｰｽ端子とﾌﾚｰﾑ端面を合わす" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "50.8mm", "164mm" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±1㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "REAR_ﾄﾞｱ周辺(IC供給有)", "WorkItems": [ "1. に指定寸法にて～をBOLT ・WASHER ・㉒・BOLT ・BOLT で取付" ], "WorkPoints": [ "端面をそろえる事", "ﾌﾚｰﾑ端面からﾎﾞﾙﾄ中央の距離", "必要部分のみ描いています", "外面", "内面", "IC供給有りの場合実施する", "ｱｰｽ端子の前面をﾌﾚｰﾑ外面と合わせる", "内面", "外面", "ﾌﾚｰﾑ端面からﾎﾞﾙﾄ中央の距離" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "23mm", "176mm", "103mm", "111mm", "152mm", "30mm", "24mm", "24mm", "72mm", "35mm", "163mm", "30mm", "188mm", "176mm", "19mm", "5mm", "3mm", "×2", "5mm", "5mm", "5mm", "5mm", "45mm" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "空圧部(電空ﾚｷﾞｭﾚｰﾀA)取付", "WorkItems": [ "1. に指定寸法にてをNUT SUPPORT BOLT WASHER で取付" ], "WorkPoints": [ "必要部分のみ描いています", "右略図､緑色部分のﾌﾚｰﾑ下面に取付", "FRONT", "下面拡大図", "ﾌﾚｰﾑ前面側から内面を見る", "ﾌﾚｰﾑ裏前から1列目で固定", "前面拡大図", "NUT SUPPORT BOLT WASHER は､ K003の付属品を使用", "ﾌﾚｰﾑ端面" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "573mm", "573mm" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法573±1㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "空圧部(電空ﾚｷﾞｭﾚｰﾀM)取付", "WorkItems": [ "1. に指定寸法にてをNUT ･SUPPORT ･BOLT ･WASHER で取付" ], "WorkPoints": [ "ﾌﾚｰﾑ前面側から内面を見る", "必要部分のみ描いています", "右略図､緑色部分のﾌﾚｰﾑ下面に取付", "FRONT", "NUT ･SUPPORT ･BOLT ･WASHER は､ K002の付属品を使用", "下面拡大図", "ﾌﾚｰﾑ裏前から1列目で固定", "前面拡大図", "ﾌﾚｰﾑ端面" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1178mm", "1178mm" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法1178±1㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾒﾝﾃﾅﾝｽﾗｲﾄ取付", "WorkItems": [ "1. に指定寸法にてをNUT SUPPORT BOLT WASHER で取付" ], "WorkPoints": [ "必要部分のみ描いています", "右略図､緑色部分のﾌﾚｰﾑ内面に取付", "FRONT", "内面図", "NUT SUPPORT BOLT WASHER は､ K001の付属品を使用", "ﾌﾚｰﾑ端面からのﾎﾞﾙﾄ中心の寸法", "ﾌﾚｰﾑ端面からのﾎﾞﾙﾄ中心の寸法", "NUT SUPPORT はﾌﾚｰﾑ側に挿入", "NUT SUPPORT はﾌﾚｰﾑ側に挿入" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "E0031", "E0033", "547mm", "547mm", "547mm", "547mm" ] }	{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法547±1㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }	information_extraction	null

{ "ToolName": "ﾍﾞﾙﾄ張力計", "Size": "", "ToolOther": "", "WorkName": "ﾄﾚｲｽﾃｰｼﾞY軸駆動部組立③", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-087" ] }

{ "QualityItem": "ﾍﾞﾙﾄﾃﾝｼｮﾝ", "ToolManageNo": "-", "ToolCycle": "1回/年", "ToolRecord": "校正成績書", "StdVal": "ﾍﾞﾙﾄ張力200~220Hz(44±4N)", "Method": "ﾍﾞﾙﾄ張力計", "RecordMethod": "WWYJ-5300-087", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "原点出し治具", "Size": "", "ToolOther": "FM-3446", "WorkName": "X軸原点調整", "WorkItems": [ "1. の原点位置を調整しｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを増し締め", "2. 1.完成品の取り外していたｶｯﾌﾟﾘﾝｸﾞ部ｶﾊﾞｰ･ﾎﾞｰﾙﾈｼﾞ部ｶﾊﾞｰを取付" ], "WorkPoints": [ "㉖原点出し治具にてモーターの原点を調整(表示を00に調整)", "ｽｹｰﾙ目で原点位置に移動させて､ﾓｰﾀｰZ相位置にてｶｯﾌﾟﾘﾝｸﾞを固定｡" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "X軸原点位置", "821mm±0.5mm 原点確認", "検査表 :<X軸> ﾓｰﾀｰ原点調整", "821㎜", "ｶｯﾌﾟﾘﾝｸﾞ固定位置", "WWYJ-5300-087" ] }

{ "QualityItem": "原点確認", "ToolManageNo": "FM-3446", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "原点位置である事", "Method": "原点出し治具", "RecordMethod": "WWYJ-5300-087", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "1000㎜", "ToolOther": "", "WorkName": "X軸原点調整", "WorkItems": [ "1. の原点位置を調整しｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを増し締め", "2. 1.完成品の取り外していたｶｯﾌﾟﾘﾝｸﾞ部ｶﾊﾞｰ･ﾎﾞｰﾙﾈｼﾞ部ｶﾊﾞｰを取付" ], "WorkPoints": [ "㉖原点出し治具にてモーターの原点を調整(表示を00に調整)", "ｽｹｰﾙ目で原点位置に移動させて､ﾓｰﾀｰZ相位置にてｶｯﾌﾟﾘﾝｸﾞを固定｡" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "X軸原点位置", "821mm±0.5mm 原点確認", "検査表 :<X軸> ﾓｰﾀｰ原点調整", "821㎜", "ｶｯﾌﾟﾘﾝｸﾞ固定位置" ] }

{ "QualityItem": "原点確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "821㎜±0.5㎜原点確認", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "", "ToolOther": "", "WorkName": "配線用ﾌﾞﾗｹｯﾄ組立", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "4.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線用ﾌﾞﾗｹｯﾄ組立", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布ｺﾞﾏ粒:2", "Method": "目視", "RecordMethod": "-", "Other": "ﾛｯｸﾀｲﾄ243", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線用ﾌﾞﾗｹｯﾄ・ｶﾊﾞｰ取付", "WorkItems": [ "▲1. にSPACER をSCREW でADHESIVE ﾛｯｸﾀｲﾄを塗布して組付け", "▲2. 1.完成品にをBOLT WASHER でADHESIVE ﾛｯｸﾀｲﾄを塗布して組付け", "3. 2.完成品にCOVER をSCREW で組付け" ], "WorkPoints": [ "拡大図" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1.完成品", "2.完成品", "接着剤塗布ｺﾞﾏ粒:2", "接着剤塗布ｺﾞﾏ粒:2" ] }

{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布ｺﾞﾏ粒:2", "Method": "目視", "RecordMethod": "-", "Other": "ﾛｯｸﾀｲﾄ243", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "空圧部ﾄﾞｯｷﾝｸﾞ", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾄﾚｲｽﾃｰｼﾞ部ﾄﾞｯｷﾝｸﾞ", "WorkItems": [ "1. にをBOLT WASHER で組付け" ], "WorkPoints": [ "A断面図" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｴｱｰ供給治具", "Size": "", "ToolOther": "FM-2823", "WorkName": "ﾄﾚｲｽﾃｰｼﾞ高さ調整", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "FM-2823", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾊｲﾄｹﾞｰｼﾞ", "Size": "600㎜", "ToolOther": "", "WorkName": "ﾄﾚｲｽﾃｰｼﾞ高さ調整", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-089", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-089" ] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "①384.5㎜±0.1㎜", "Method": "ﾊｲﾄｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5300-089", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾊｲﾄｹﾞｰｼﾞ", "Size": "600㎜", "ToolOther": "", "WorkName": "ﾄﾚｲｽﾃｰｼﾞ高さ調整", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-089", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-089" ] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "②417.5㎜±0.1㎜", "Method": "ﾊｲﾄｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5300-089", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ﾊｲﾄｹﾞｰｼﾞ", "Size": "600㎜", "ToolOther": "", "WorkName": "ﾄﾚｲｽﾃｰｼﾞ高さ調整", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-089", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-089" ] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "③412.0㎜±0.1㎜", "Method": "ﾊｲﾄｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5300-089", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線配管引き回し①", "WorkItems": [ "1. にLABEL TERMINAL PROCESS LABEL TERMINAL PROCESS のﾀｸﾞをを取付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ITVEM4111P", "E0501R", "ITVMM4111P", "ITYEM4110P", "ITXEM4109P", "ITYMM4110P", "ITXMM4109P" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線配管引き回し②", "WorkItems": [ "1. にCABLE CABLE CABLE の配線を取付" ], "WorkPoints": [ "拡大図" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ITVME4111R", "E0501P", "ITVMM4111R", "ITVME4111P", "E0501R", "ITVMM4111P", "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "ｲﾝｼｭﾛｯｸ(100mm)", "ｲﾝｼｭﾛｯｸ(300mm)", "接続確認", "検査表 :接続確認 (3)ICﾄﾚｲｽﾃｰｼﾞ部(正流れｽﾃｰｼﾞ)", "WWYJ-5300-115" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "WWYJ-5300-115", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線配管引き回し③", "WorkItems": [ "1. にCABLE CABLE の配線を取付" ], "WorkPoints": [ "ﾍﾞﾙﾄの下を通す", "A断面図", "B矢視図(ﾄﾚｲｽﾃｰｼﾞ下(Y軸部))" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :接続確認 (4)ICﾄﾚｲｽﾃｰｼﾞ部(正流れｽﾃｰｼﾞD1500)", "1B11010R", "1B11020R", "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "ｲﾝｼｭﾛｯｸ(100mm)", "B11015R", "接続確認", "検査表 :接続確認 (2)ICﾄﾚｲｽﾃｰｼﾞ部(ITY軸)", "接続確認", "WWYJ-5300-115" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "WWYJ-5300-115", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線配管引き回し④", "WorkItems": [ "1. にTUBE の配管を㉖で長さを調整し接続" ], "WorkPoints": [ "A矢視図", "L側配管を接続後､R側配管を接続し支柱にｲﾝｼｭﾛｯｸで固定", "支柱の内側へ", "B矢視図", "支柱の内側へ", "C断面図", "D断面図", "⑥の反対の端にﾏｽｷﾝｸﾞﾃｰﾌﾟで配管接続番号が判る様に明記の事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "L1", "L2", "R2", "R1", "L1", "L2", "R2", "R1", "下段Down", "下段Up", "上段Down", "上段Up", "下段Down", "下段Up", "上段Down", "上段Up", "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "ｲﾝｼｭﾛｯｸ(150mm)" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "", "ToolOther": "", "WorkName": "配線配管引き回し⑤", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線配管引き回し⑥", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-115", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-115" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "WWYJ-5300-115", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線配管引き回し⑦", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "配線配管引き回し⑧", "WorkItems": [ "1. にTUBE ･TUBE の配管をｶｯﾄして接続" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "φ4黒 130mm", "φ6橙 70mm", "φ6橙 110mm" ] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "配線配管引き回し⑨", "WorkItems": [ "1. にXｽﾃｰｼﾞからの配管をｶｯﾄして接続" ], "WorkPoints": [ "φ4黒配管接続図", "φ4黒 6芯ﾁｭｰﾌﾞ", "A矢視図(ﾄﾚｲ吸着)", "B矢視図(ﾄﾚｲｽﾃｰｼﾞ上下)" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ(100mm)", "ｲﾝｼｭﾛｯｸ(200mm)", "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "配線配管引き回し⑩", "WorkItems": [ "1. にCABLE CABLE CABLE の配線を接続" ], "WorkPoints": [ "接続確認" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :接続確認 (1)ICﾄﾚｲｽﾃｰｼﾞ部(ITX軸ｾﾝｻｰ､ﾊﾞﾙﾌﾞ)", "整線時はX軸ﾄﾞｸﾞとの干渉に注意", "ｲﾝｼｭﾛｯｸ(100mm)", "B10944R", "R31034R", "R31035R", "R31036R", "R31037R", "G2A020", "G2A021", "R31044R", "R31045R", "R31046R", "R31047R", "R31031R", "R31032R", "R31033R", "R31041R", "R31042R", "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定", "WWYJ-5300-115" ] }

{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "WWYJ-5300-115", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｺﾝﾍﾞｯｸｽ", "Size": "3m", "ToolOther": "", "WorkName": "配線配管引き回し⑪", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±1㎜", "Method": "ｺﾝﾍﾞｯｸｽ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "引き渡し準備", "WorkItems": [ "1. ･COVER ･COVER ･SCREW ･CLAMPER ･SPACER ･BOLT ･WASHER ･BOLT ･BOLT ･WASHER ･WASHER を本体載せ込み工程に引き渡す" ], "WorkPoints": [ "ｶﾊﾞｰの取付は本体載せ込み完了後に実施の事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "引き渡し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き渡し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾄﾚｲｽﾃｰｼﾞ組立①", "WorkItems": [ "2. PLATE ･PLATE にPAD を取付け", "1. PLATE ･PLATE のｴｱｰ経路が指示通り通っていることを確認する", "3. 2.完成品にBRACKET ･BRACKET をSCREW で組付け" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業ではそれぞれ2個作成", "この作業ではそれぞれ2個作成", "組付け詳細" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾄﾚｲｽﾃｰｼﾞ組立②", "WorkItems": [ "1. ･にBRACKET をBOLT ･WASHER で組付け", "2. 1.完成品にJOINT を組付け" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業ではそれぞれ2個作成", "この作業ではそれぞれ2個作成" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾄﾚｲｽﾃｰｼﾞ組立③", "WorkItems": [ "1. TUBE を指定の長さでｶｯﾄ", "2. ･に1.完成品を組付け" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業ではそれぞれ2個作成", "TUBE φ4白 100㎜ 4本" ] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法:100㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ICﾄﾚｲｽﾃｰｼﾞ部へ引き渡し", "WorkItems": [ "1. ･･BOLT ･WASHER を引き渡す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "ﾌﾚｰﾑ1", "WorkItems": [ "1. BLOCK FRAME FRAME をNUT NUT BOLT BOLT で取付" ], "WorkPoints": [ "寸法通り取付けるBLOCK FRAME FRAME の合わせ面に隙間が無い事", "2ｾｯﾄ製作" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "271㎜", "119㎜", "119㎜" ] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌﾚｰﾑ2", "WorkItems": [ "1. にPLATE をPLATE で挟んでBOLT WASHER で取付", "1. にPLATE をPLATE で挟んでBOLT WASHER で取付" ], "WorkPoints": [ "左ﾊﾝﾄﾞ組立", "右ﾊﾝﾄﾞ組立" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "", "ToolOther": "1/100", "WorkName": "ﾌﾚｰﾑ3", "WorkItems": [ "1. を定盤上でN015ﾌﾚｰﾑ上面の高さを測定する" ], "WorkPoints": [ "2ﾋﾟｰｽ測定", "0.4㎜以内", "P002の下面と定盤に隙間が無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :P(2軸)3 ｱﾙﾑﾌﾚｰﾑ高さ測定", "A001", "P005､P006", "P004", "N015", "P003", "定盤", "1~4相互の高低差を確認", "WWYJ-5300-46" ] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "高低差0.4㎜以内", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5300-46", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "左ﾌﾚｰﾑ", "WorkItems": [ "1. FRAME にBRACKET をNUT BOLT WASHER で取付", "2. 1.完成品にJOINT をBOLT WASHER WASHER で取付", "3. 2.完成品にCABLE-SUPPORT を取付", "4. 3.完成品にNUT を入れる", "1. FRAME にBRACKET をNUT BOLT WASHER で取付", "2. 1.完成品にJOINT をBOLT WASHER WASHER で取付", "3. 2.完成品にCABLE-SUPPORT を取付", "4. 3.完成品にNUT を入れる" ], "WorkPoints": [ "FRAME は方向あり", "FRAME の裏面に8個入れる", "FRAME の表面に2個入れる位置は不問", "FRAME の裏面に4個入れる位置は不問", "FRAME の測面に2個入れる位置は不問", "FRAME の表面に2個入れる位置は不問", "FRAME は方向あり", "FRAME の裏面に8個入れる", "FRAME の表面に2個入れる位置は不問", "FRAME の裏面に4個入れる位置は不問", "FRAME の測面に2個入れる位置は不問", "FRAME の表面に2個入れる位置は不問" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "230㎜", "166.3㎜", "45㎜", "15㎜", "28㎜", "120㎜", "230㎜", "166.3㎜", "45㎜", "15㎜", "28㎜", "120㎜" ] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "右ﾌﾚｰﾑ", "WorkItems": [ "1. FRAME にBRACKET をNUT BOLT WASHER で取付", "2. 1.完成品にJOINT をBOLT WASHER WASHER で取付", "3. 2.完成品にCABLE-SUPPORT を取付", "4. 3.完成品にNUT を入れる", "1. FRAME にBRACKET をNUT BOLT WASHER で取付", "2. 1.完成品にJOINT をBOLT WASHER WASHER で取付", "3. 2.完成品にCABLE-SUPPORT を取付", "4. 3.完成品にNUT を入れる" ], "WorkPoints": [ "FRAME は方向あり", "FRAME の裏面に8個入れる", "FRAME の測面に2個入れる位置は不問", "FRAME の表面に2個入れる位置は不問", "FRAME の裏面に4個入れる位置は不問", "FRAME の表面に2個入れる位置は不問", "FRAME は方向あり", "FRAME の裏面に8個入れる", "FRAME の測面に2個入れる位置は不問", "FRAME の表面に2個入れる位置は不問", "FRAME の裏面に4個入れる位置は不問", "FRAME の表面に2個入れる位置は不問" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "銘板貼付け1", "WorkItems": [ "1. にLABEL を貼付け" ], "WorkPoints": [ "2ｾｯﾄ製作" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾒﾓﾘとの合わせ基準", "ﾒﾓﾘとの合わせ基準" ] }

{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法の位置に貼付けている事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "銘板貼付け2", "WorkItems": [ "1. にLABEL を貼付け" ], "WorkPoints": [ "この範囲の貼付け寸法を明示右側も同じ", "2ｾｯﾄ製作" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "2㎜", "5㎜", "80㎜", "5㎜", "5㎜", "230㎜", "5㎜", "5㎜", "5㎜", "2㎜", "80㎜", "230㎜" ] }

{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法の位置に貼付けている事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "銘板貼付け3", "WorkItems": [ "1. BRACKET にLABEL を貼付け", "3. BRACKET にLABEL を貼付け", "4. 3.完成品にCABLE-SUPPORT を取付ける", "2. 1.完成品にCABLE-SUPPORT を取付ける" ], "WorkPoints": [ "左ﾊﾝﾄﾞ用", "右ﾊﾝﾄﾞ用" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "23㎜", "155㎜", "155㎜", "23㎜" ] }

{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法の位置に貼付けている事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "銘板貼付け4", "WorkItems": [ "1. COVER にLABEL を貼付け", "3. COVER にLABEL を貼付け", "4. 3.完成品にCABLE-SUPPORT を取付ける", "2. 1.完成品にCABLE-SUPPORT を取付ける" ], "WorkPoints": [ "注) AMPP構成時", "注) AMP構成時はこちらを貼る", "左ﾊﾝﾄﾞ用", "右ﾊﾝﾄﾞ用" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "32㎜", "2㎜", "32㎜", "2㎜" ] }

{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法の位置に貼付けている事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾊﾝﾄﾞﾊﾞﾙﾌﾞ1", "WorkItems": [ "1. JOINT SPACER JOINT を取付" ], "WorkPoints": [ "16ｾｯﾄ製作" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "", "ToolOther": "", "WorkName": "ﾊﾝﾄﾞﾊﾞﾙﾌﾞ2", "WorkItems": [ "1. にJOINT を取付(4か所)", "2. 1.完成品にVALVE をBOLT WASHER WASHER で取付(12か所)", "1. 2｡完成品のJOINT VALVE にを取付(16か所)" ], "WorkPoints": [ "VALVE は方向あり", "左ﾊﾝﾄﾞ用", "右ﾊﾝﾄﾞ用", "矢印方向に取付" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "10㎜", "10㎜" ] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法:10.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "治具", "Size": "", "ToolOther": "FM-6046", "WorkName": "搬送PAD組立①", "WorkItems": [ "1. BLOCK にVACUUM-PAD を仮取付(ﾅｯﾄはVACUUM-PAD の付属品を使用)", "3. PAD高さ調整を行う｡", "2. 1.完成品を㉗搬送PAD高さ合わせジグに取付" ], "WorkPoints": [ "32ｾｯﾄ製作" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-46" ] }

{ "QualityItem": "隙間確認", "ToolManageNo": "FM-6046", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "29.8±0.1㎜(隙間0.1㎜以内)", "Method": "治具", "RecordMethod": "WWYJ-5300-46", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "", "ToolOther": "", "WorkName": "搬送PAD組立①", "WorkItems": [ "1. BLOCK にVACUUM-PAD を仮取付(ﾅｯﾄはVACUUM-PAD の付属品を使用)", "3. PAD高さ調整を行う｡", "2. 1.完成品を㉗搬送PAD高さ合わせジグに取付" ], "WorkPoints": [ "32ｾｯﾄ製作" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-46" ] }

{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "29.8±0.1㎜(隙間0.1㎜以内)", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5300-46", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "搬送PAD組立②", "WorkItems": [ "▲1. にの付属品をADHESIVE ﾈｼﾞﾛｯｸ材で取付", "▲2. 1.完成品上部の付属品のﾌﾟﾗｸﾞを取り外し､JOINT をADHESIVE ﾈｼﾞﾛｯｸ材で取付ｼﾞｮｲﾝﾄの向き注意" ], "WorkPoints": [ "吸着穴に接着剤が混入し無い事", "吸着穴に接着剤が混入し無い事", "4ｾｯﾄ製作", "8ｾｯﾄ製作", "4ｾｯﾄ製作", "下部ｼﾞｮｲﾝﾄと上部ｼﾞｮｲﾝﾄの向き違いがある3種類製作する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :AM2､ねじﾛｯｸ塗布", "検査表 :AM2､ねじﾛｯｸ塗布", "接着剤塗布ｺﾞﾏ粒:2", "接着剤塗布ｺﾞﾏ粒:2", "ADHESIVE ねじﾛｯｸ塗布", " の付属品(ADHESIVE ねじﾛｯｸ塗布)", "WWYJ-5300-46" ] }

{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布ｺﾞﾏ粒:2", "Method": "目視", "RecordMethod": "WWYJ-5300-46", "Other": "ﾛｯｸﾀｲﾄ243", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "搬送PAD組立③", "WorkItems": [ "▲1. にの付属品をADHESIVE ﾈｼﾞﾛｯｸ材で取付" ], "WorkPoints": [ "吸着穴に接着剤が混入し無い事", "16ｾｯﾄ製作" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :AM2､ねじﾛｯｸ塗布", "接着剤塗布ｺﾞﾏ粒:2", " の付属品(ADHESIVE ねじﾛｯｸ塗布)", " の付属品(ADHESIVE ねじﾛｯｸ塗布)", "WWYJ-5300-46" ] }

{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布ｺﾞﾏ粒:2", "Method": "目視", "RecordMethod": "WWYJ-5300-46", "Other": "ﾛｯｸﾀｲﾄ243", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "左吸着ﾊﾝﾄﾞ組立1", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "210㎜" ] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法:210.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "左吸着ﾊﾝﾄﾞ組立2", "WorkItems": [ "1. をにNUT BOLT WASHER で取付" ], "WorkPoints": [ "端面合わせ" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "左吸着ﾊﾝﾄﾞ組立3", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "5㎜", "110㎜", "110㎜", "40㎜", "40㎜", "40㎜", "40㎜", "110㎜", "5㎜", "110㎜" ] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "左吸着ﾊﾝﾄﾞ組立4", "WorkItems": [ "1. にTUBE TUBE TUBE TUBE TUBE を取付", "2. 各配管を㉘で固定" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "左吸着ﾊﾝﾄﾞ組立5", "WorkItems": [ "▲1. CAP CAP に㉖を塗布しに取付" ], "WorkPoints": [ "CAP の中央部2本の爪は㉘で切断する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :(P2軸)2,接着剤塗布", "接着剤塗布小豆:2", "WWYJ-5300-46" ] }

{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布小豆:2", "Method": "目視", "RecordMethod": "WWYJ-5300-46", "Other": "ﾛｯｸﾀｲﾄ415", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "右吸着ﾊﾝﾄﾞ組立1", "WorkItems": [ "1. にをNUT BOLT WASHER で仮付け", "2. BRACKET BRACKET をNUT WASHER BOLT WASHER で仮付け", "3. 取付位置を210㎜に合わせ､各部品を隙間なく取付ける(本締め)" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法:210.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "右吸着ﾊﾝﾄﾞ組立2", "WorkItems": [ "1. をにNUT BOLT WASHER で取付" ], "WorkPoints": [ "端面合わせ" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "右吸着ﾊﾝﾄﾞ組立3", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "5㎜", "110㎜", "110㎜", "40㎜", "40㎜", "40㎜", "40㎜", "110㎜", "5㎜", "110㎜" ] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "ｽｹｰﾙ", "Size": "", "ToolOther": "", "WorkName": "右吸着ﾊﾝﾄﾞ組立4", "WorkItems": [ "1. にTUBE TUBE TUBE TUBE TUBE を取付", "2. 各配管を㉘で固定" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定又は板金に固定" ] }

{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "右吸着ﾊﾝﾄﾞ組立5", "WorkItems": [ "▲1. CAP CAP にADHESIVE を塗布しに取付" ], "WorkPoints": [ "CAP の中央部2本の爪は㉘で切断する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :(P2軸)2､接着剤塗布", "接着剤塗布小豆:2", "WWYJ-5300-46" ] }

{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布小豆:2", "Method": "目視", "RecordMethod": "WWYJ-5300-46", "Other": "ﾛｯｸﾀｲﾄ415", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "次工程へ引き渡し", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1. BOLT BOLT WASHER WASHER BOLT WASHER を次工程へ｡" ] }

{ "QualityItem": "引き渡し部材確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "正しい部材が引き渡される事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｾﾝﾀﾘﾝｸﾞﾌﾞﾛｯｸ取付", "WorkItems": [ "1. の取付用ﾎﾞﾙﾄ､ﾜｯｼｬを使ってBLOCK を取付" ], "WorkPoints": [ "PINに当付け" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾒﾝﾃﾅﾝｽﾗｲﾄP組立", "WorkItems": [ "SFN-SA4 4個", "SFA-9A2 4個", "六角穴付きﾎﾞﾙﾄM4×10 4本平座金みがき丸 4 4個", "1. BRACKET にLED-LAMP-UNIT をBOLT WASHER WASHER で取付ける", "2. 1の完成品にLABEL TERMINAL PROCESS を取付ける", "3. 2の完成品とNUT SUPPORT BOLT WASHER を付属する" ], "WorkPoints": [ "合わせる", "ﾗﾍﾞﾙ2種類" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "E0131R", "E0131R", "E0231R", "この作業ではﾗﾍﾞﾙ違いを2個製作" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6481", "WorkName": "ﾏｸﾞﾈｯﾄ取付け", "WorkItems": [ "1. ﾊｰﾈｽﾎﾞｰﾄﾞにﾏｸﾞﾈｯﾄを取付ける" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "⇒ﾏｸﾞﾈｯﾄ中", "⇒ﾏｸﾞﾈｯﾄ大" ] }

{ "QualityItem": "取付確認", "ToolManageNo": "FM-6481", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾊｰﾈｽ準備", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1.下記ﾘｽﾄの順番でｹｰﾌﾞﾙを準備する" ] }

{ "QualityItem": "ｹｰﾌﾞﾙの準備", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り準備する事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }

information_extraction

0

null

{ "ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ", "Size": "", "ToolOther": "FM-6481", "WorkName": "ﾊｰﾈｽ引き回1", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "CN8K011", "R31140RR31141R", "1. CABLE を引き回す" ] }