input stringclasses 1
value | instruction stringlengths 222 1.92k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "MC-Stype2ﾍﾞｰｽﾌﾟﾚｰﾄ用ﾋﾟﾝ圧入ｼﾞｸ",
"Size": "",
"ToolOther": "FM-6018",
"WorkName": "ﾚﾝｽﾞ取付け",
"WorkItems": [
"1. PLATE にPIN を圧入する",
"3. 2完成品に をBOLT WASHER で取付ける",
"2. 1完成品にCUSHION を貼付ける"
],
"WorkPoints": [
"反対側も同様に取付ける",
"L側",
"R側",
"ｸｯｼｮﾝ",
"ﾌﾟﾚｰﾄの... | {
"QualityItem": "出代確認",
"ToolManageNo": "FM-6018",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾚﾝｽﾞ取付け",
"WorkItems": [
"3. 2完成品に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"反対側も同様に取付ける",
"L側",
"R側",
"ｸｯｼｮﾝ"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"Inspection... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｼｬﾌﾄ・ｾﾝｻｰｷｯﾄ取付け",
"WorkItems": [
"1. にSHAFT SHAFT をBOLT WASHER で取付ける",
"★2. 1完成品を反転して治具に搭載し をSCREW で取付ける"
],
"WorkPoints": [
"ｸｯｼｮﾝ",
"反対側も同様に取付ける",
"矢印方向に押し当て取付けの事",
"埃等入らぬよう注意する事",
"Hｶｯﾄの... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "60cN･m",
"WorkName": "ｼｬﾌﾄ・ｾﾝｻｰｷｯﾄ取付け",
"WorkItems": [
"1. にSHAFT SHAFT をBOLT WASHER で取付ける",
"★2. 1完成品を反転して治具に搭載し をSCREW で取付ける"
],
"WorkPoints": [
"ｸｯｼｮﾝ",
"反対側も同様に取付ける",
"矢印方向に押し当て取付けの事",
"埃等入らぬよう注意する事",
"H... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "MC-S用組立台(Type2)",
"Size": "",
"ToolOther": "FM-5877",
"WorkName": "ｼｬﾌﾄ・ｾﾝｻｰｷｯﾄ取付け",
"WorkItems": [
"1. にSHAFT SHAFT をBOLT WASHER で取付ける",
"★2. 1完成品を反転して治具に搭載し をSCREW で取付ける"
],
"WorkPoints": [
"ｸｯｼｮﾝ",
"反対側も同様に取付ける",
"矢印方向に押し当て取付けの事",
"埃等入らぬよう注意する事",
... | {
"QualityItem": "設置確認",
"ToolManageNo": "FM-5877",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り設置出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "P610前組み",
"WorkItems": [
"1. BRACKET にBUSH を取付けCUSHION を貼付ける",
"2. 1完成品にSPACER をSCREW WASHER NUT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words":... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "35cN･m",
"WorkName": "P610前組み",
"WorkItems": [],
"WorkPoints": [
"ｴｯｼﾞに合わせて貼付けの事",
"12.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 35cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "35cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "P601・P607前組み",
"WorkItems": [
"2. BRACKET にBUSH を取付ける",
"1. BRACKET にCUSHION を貼付ける"
],
"WorkPoints": [
"4㎜",
"面に当付けて貼付けの事",
"面に合わせて貼付けの事",
"左右対称に貼付けの事",
"面に当付けて貼付けの事",
"面に合わせて貼付けの事"
],
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "48cN･m",
"WorkName": "BOX・ﾎﾙﾀﾞｰ前組み",
"WorkItems": [
"1. BOX にBRACKET をWASHER BOLT で取付ける",
"2. HOLDER にCUSHION を貼付ける"
],
"WorkPoints": [
"BRACKET を奥方向に当付けの事",
"P227のｴｯｼﾞに合わせて貼付けの事"
],
"Tolks": [
"締付ﾄﾙｸ 48cN･m"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "48cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "3Dﾌｫｰｶｽ高さ･ｲﾒｰｼﾞｬ位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5833",
"WorkName": "調整準備1",
"WorkItems": [
"1. を治具に取付ける"
],
"WorkPoints": [
"治具に載せ奥に当付ける",
"治具のﾋﾟﾝに挿入する",
"ﾌﾟﾚｰﾄをｽﾗｲﾄﾞし落下防止させる",
"付属ﾎﾞﾙﾄで固定する",
"付属ﾎﾞﾙﾄで固定する",
"取付け方向に注意する事",
"ｸｯｼｮﾝ"
],... | {
"QualityItem": "設置確認",
"ToolManageNo": "FM-5833",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り設置出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "3Dﾌｫｰｶｽ高さ･ｲﾒｰｼﾞｬ位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5833",
"WorkName": "調整準備2",
"WorkItems": [
"★1. の取付け･接続を行う"
],
"WorkPoints": [
"CN1",
"CN2",
"ﾌﾚｷｹｰﾌﾞﾙを接続する",
"反対側も同様に接続する",
"CN1",
"CN1",
"CN2",
"CN2",
"付属ﾎﾞﾙﾄで固定する",
"ﾎﾞﾙ... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-5833",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り接続している事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "3Dﾌｫｰｶｽ高さ･ｲﾒｰｼﾞｬ位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5833",
"WorkName": "調整準備3",
"WorkItems": [
"4. 『Device Capture』を押す",
"1. 電源をONする",
"2. 『NPM_PartsEditer』を起動させる",
"3. 『Coherix』を押す",
"3. 『Coherix』を押す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5833",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "3Dﾌｫｰｶｽ高さ･ｲﾒｰｼﾞｬ位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5833",
"WorkName": "ｾﾝｻｰ感度登録の確認",
"WorkItems": [
"1. ﾕﾆｯﾄｼﾘｱﾙNo.を入力し､『3DLｾﾝｻ感度』を押す",
"3. 『3DRｾﾝｻ感度』を押す",
"4. ｾﾝｻｰｷｯﾄにﾊﾟﾗﾒｰﾀが書込まれている事を確認し『OK』を押す",
"2. ｾﾝｻｰｷｯﾄにﾊﾟﾗﾒｰﾀが書込まれている事を確認し『OK』を押す"
],
"WorkPoints": [
... | {
"QualityItem": "登録確認",
"ToolManageNo": "FM-5833",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "Offset:0以外ImgGain:47以外",
"Method": "目視",
"RecordMethod": "2LC-JG-22006",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "3Dﾌｫｰｶｽ高さ･ｲﾒｰｼﾞｬ位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5833",
"WorkName": "ﾋﾟﾝﾄ・ｾﾝｻ位置調整1",
"WorkItems": [
"1. 『D:MCS調整』を選択､反射IDLに17を入力､『TS2とContinue』にﾁｪｯｸし『Capture』を押し撮像を開始する"
],
"WorkPoints": [
"TS2ﾁｪｯｸ時:R側 TS4ﾁｪｯｸ時:L側"
],
"Tolks": [],
"InspectionNo": "",
"In... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5833",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "3Dﾌｫｰｶｽ高さ･ｲﾒｰｼﾞｬ位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5833",
"WorkName": "ﾋﾟﾝﾄ・ｾﾝｻ位置調整2",
"WorkItems": [
"1. 画面を見ながらﾋﾟﾝﾄ･位置を調整する"
],
"WorkPoints": [
"2ヶ所のｾｯﾄﾋﾞｽを緩める",
"ﾚﾝｽﾞを回し調整する",
"θ回転調整",
"各ﾀﾞｲﾔﾙｹﾞｰｼﾞを回し調整する",
"X方向調整",
"Y方向調整",
"ﾚﾝｽﾞのｷｬｯﾌﾟ... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5833",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "3Dﾌｫｰｶｽ高さ･ｲﾒｰｼﾞｬ位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5833",
"WorkName": "ﾋﾟﾝﾄ・ｾﾝｻ位置調整3",
"WorkItems": [
"3. TS2終了後､TS4も同様に調整を行う",
"2. 調整終了後『Stop』⇒ 『調整完了』を押す",
"1. ﾋﾟﾝﾄ･位置調整が両方共に規格値に入るまで繰り返し調整し締結する"
],
"WorkPoints": [
"ﾎﾞﾙﾄ締結",
"T=θ",
"ﾋﾟﾝﾄ規格値:FocusEva... | {
"QualityItem": "ﾋﾟﾝﾄ確認",
"ToolManageNo": "FM-5833",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "FocusEval<2.0",
"Method": "目視",
"RecordMethod": "2LC-JG-22006",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "3Dﾌｫｰｶｽ高さ･ｲﾒｰｼﾞｬ位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5833",
"WorkName": "ﾋﾟﾝﾄ・ｾﾝｻ位置調整3",
"WorkItems": [
"3. TS2終了後､TS4も同様に調整を行う",
"2. 調整終了後『Stop』⇒ 『調整完了』を押す",
"1. ﾋﾟﾝﾄ･位置調整が両方共に規格値に入るまで繰り返し調整し締結する"
],
"WorkPoints": [
"ﾎﾞﾙﾄ締結",
"T=θ",
"ﾋﾟﾝﾄ規格値:FocusEva... | {
"QualityItem": "ﾋﾟﾝﾄ確認",
"ToolManageNo": "FM-5833",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "左右のﾁｬｰﾄの見え方が同程度である事",
"Method": "目視",
"RecordMethod": "2LC-JG-22006",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "3Dﾌｫｰｶｽ高さ･ｲﾒｰｼﾞｬ位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5833",
"WorkName": "ﾋﾟﾝﾄ・ｾﾝｻ位置調整3",
"WorkItems": [
"3. TS2終了後､TS4も同様に調整を行う",
"2. 調整終了後『Stop』⇒ 『調整完了』を押す",
"1. ﾋﾟﾝﾄ･位置調整が両方共に規格値に入るまで繰り返し調整し締結する"
],
"WorkPoints": [
"ﾎﾞﾙﾄ締結",
"T=θ",
"ﾋﾟﾝﾄ規格値:FocusEva... | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-5833",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "X=1920±5[pix]Y=1080±5[pix]θ=±0.1°以内",
"Method": "目視",
"RecordMethod": "2LC-JG-22006",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "50cN･m",
"WorkName": "ﾋﾟﾝﾄ・ｾﾝｻ位置調整3",
"WorkItems": [
"3. TS2終了後､TS4も同様に調整を行う",
"2. 調整終了後『Stop』⇒ 『調整完了』を押す",
"1. ﾋﾟﾝﾄ･位置調整が両方共に規格値に入るまで繰り返し調整し締結する"
],
"WorkPoints": [
"ﾎﾞﾙﾄ締結",
"T=θ",
"ﾋﾟﾝﾄ規格値:FocusEval<2.0 ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾋﾟﾝﾄ・ｾﾝｻ位置調整3",
"WorkItems": [
"3. TS2終了後､TS4も同様に調整を行う",
"2. 調整終了後『Stop』⇒ 『調整完了』を押す",
"1. ﾋﾟﾝﾄ･位置調整が両方共に規格値に入るまで繰り返し調整し締結する"
],
"WorkPoints": [
"ﾎﾞﾙﾄ締結",
"T=θ",
"ﾋﾟﾝﾄ規格値:FocusEval<2.0 ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "3Dﾌｫｰｶｽ高さ･ｲﾒｰｼﾞｬ位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5833",
"WorkName": "画像内異物確認",
"WorkItems": [
"1. 異物確認用照明を移動させる",
"3. 撮像した画像に異物の影等が無い事を確認する",
"4. TS4も同様の手順で確認する",
"5. 確認後､治具から取り外す",
"2. 『0:Guide』を選択､『TS2』をﾁｪｯｸ 『Continue』のﾁｪｯｸを外し『Capture』を押し撮像する"
],
"W... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5833",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "画像内に映り込みが無い事",
"Method": "目視",
"RecordMethod": "2LC-JG-22006",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｹｰﾌﾞﾙ曲げｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6060",
"WorkName": "ﾌﾚｷｹｰﾌﾞﾙ折り曲げ・取付け",
"WorkItems": [
"1. CABLE CABLE CABLE CABLE を折り曲げ線通りに折る",
"2. 1完成品を にCABLE-SUPPORT で取付ける"
],
"WorkPoints": [
"Bottom_L用",
"Top_L用",
"Top_R用",
"Bottom_R用",
"山折り: 谷折... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-6060",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｷｹｰﾌﾞﾙ接続",
"WorkItems": [
"2. 1完成品のﾌﾚｷｹｰﾌﾞﾙを で固定する",
"★1. のﾌﾚｷｹｰﾌﾞﾙを に接続する"
],
"WorkPoints": [
"ｸｯｼｮﾝ",
"ｺﾈｸﾀのﾂﾒを手前に倒しﾛｯｸする",
"ﾎﾞｽ",
"左右のﾎﾞｽが溝にはまっている事",
"白線がｺﾈｸﾀと平行になる様挿入",
"CN2",
"CN1",
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "斜め挿し無き事",
"Method": "目視",
"RecordMethod": "2LC-JG-22006",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾌﾞﾗｹｯﾄ固定",
"WorkItems": [
"1. のﾌﾞﾗｹｯﾄをBOLT WASHER で取付ける"
],
"WorkPoints": [
"面を合わせる事",
"矢印方向に押し当て取付けの事",
"ﾌﾚｷがｴｯｼﾞに接触無き事",
"反対側も同様に取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"Insp... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "60cN･m",
"WorkName": "ﾌﾞﾗｹｯﾄ固定",
"WorkItems": [
"2. 1完成品のﾌﾞﾗｹｯﾄをWASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾗｹｯﾄ固定",
"WorkItems": [
"1. のﾌﾞﾗｹｯﾄをBOLT WASHER で取付ける",
"2. 1完成品のﾌﾞﾗｹｯﾄをWASHER BOLT で取付ける"
],
"WorkPoints": [
"面を合わせる事",
"矢印方向に押し当て取付けの事",
"ﾌﾚｷがｴｯｼﾞに接触無き事",
"反対側も同様に取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 15... | {
"QualityItem": "外観確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾌﾚｷがｴｯｼﾞに接触無き事",
"Method": "目視",
"RecordMethod": "2LC-JG-22006",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "90cN･m",
"WorkName": "ﾌﾚｷｹｰﾌﾞﾙ固定",
"WorkItems": [
"1. に をSPACER SCREW SCREW で取付ける",
"2. 1完成品を反転して治具に搭載し を貼付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 90cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Work... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｷｹｰﾌﾞﾙ固定",
"WorkItems": [],
"WorkPoints": [
"面を合わせて取付けの事",
"1㎜",
"1㎜",
"ｸｯｼｮﾝ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :10.ｼﾘｱﾙﾗﾍﾞﾙ"
]... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "BOX・ﾎﾙﾀﾞ取付け",
"WorkItems": [
"1. に をSCREW で仮取付けする",
"2. 1完成品に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"反対側も同様に取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "50cN･m",
"WorkName": "BOX・ﾎﾙﾀﾞ取付け",
"WorkItems": [
"1. に をSCREW で仮取付けする",
"2. 1完成品に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"反対側も同様に取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItem... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "3D検査用ｶﾒﾗ",
"Size": "",
"ToolOther": "",
"WorkName": "3D検査準備1",
"WorkItems": [
"★1. を㉖に搭載しﾌﾚｷｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [
"ﾊｰﾌﾐﾗｰ･ﾌﾚｷｹｰﾌﾞﾙに注意して取付けの事",
"ﾌﾚｷｹｰﾌﾞﾙの斜め挿し無き事",
"TYPE2ﾕﾆｯﾄ上で調整の場合は検査不要",
"CN2･3",
"CN4･5",
"ｺﾈｸﾀのﾂﾒを起こす",
"ｺﾈｸﾀのﾂﾒを倒しﾛｯ... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りに出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "MC-S用完成品検査ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5961",
"WorkName": "3D検査準備2",
"WorkItems": [
"1. を治具に搭載する",
"2. 治具ｹｰﾌﾞﾙを接続し電源を入れる"
],
"WorkPoints": [
"矢印方向に当付け搭載する",
"ﾚﾊﾞｰﾛｯｸで位置決めしﾎﾞﾙﾄで固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-5961",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "3DI/Fﾎﾞｰﾄﾞ前組み",
"WorkItems": [
"■★1. PANASONIC I/F BOARD-3D の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を記入する",
"★2. PANASONIC I/F BOARD-3D にSHEET SHEET SHEET SHEET を貼付ける",
"★3. 2完成品にHEAT-SINK をSCREW で取付ける"
],
"WorkPoints": [
"12.5㎜",
"20.5... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致している事",
"Method": "目視",
"RecordMethod": "2LC-JG-22006",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "3DI/Fﾎﾞｰﾄﾞ前組み",
"WorkItems": [
"■★1. PANASONIC I/F BOARD-3D の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を記入する",
"★2. PANASONIC I/F BOARD-3D にSHEET SHEET SHEET SHEET を貼付ける",
"★3. 2完成品にHEAT-SINK をSCREW で取付ける"
],
"WorkPoints": [
"12.5㎜",
"20.5... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-22006",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "3DI/Fﾎﾞｰﾄﾞ前組み",
"WorkItems": [
"■★1. PANASONIC I/F BOARD-3D の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を記入する",
"★2. PANASONIC I/F BOARD-3D にSHEET SHEET SHEET SHEET を貼付ける",
"★3. 2完成品にHEAT-SINK をSCREW で取付ける"
],
"WorkPoints": [
"両面の保護ｼｰﾄを剥が... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "40cN･m",
"WorkName": "3DI/Fﾎﾞｰﾄﾞ前組み",
"WorkItems": [
"■★1. PANASONIC I/F BOARD-3D の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を記入する",
"★2. PANASONIC I/F BOARD-3D にSHEET SHEET SHEET SHEET を貼付ける",
"★3. 2完成品にHEAT-SINK をSCREW で取付ける"
],
"WorkPoints": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "放熱ｼｰﾄ貼付ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6220",
"WorkName": "P608前組み",
"WorkItems": [
"1. BRACKET にSHEET を貼付ける"
],
"WorkPoints": [
"貼付け面のみ保護ｼｰﾄを剥がす事",
"当付け",
"当付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wor... | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-6220",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに貼付け出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-22006",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾋｰﾄｼﾝｸ・MASK前組み",
"WorkItems": [
"1. HEAT-SINK にSHEET SHEET を貼付ける",
"2. MASK にCUSHION を貼付ける"
],
"WorkPoints": [
"P222のｴｯｼﾞに合わせて貼付けの事",
"3㎜",
"P606のｴｯｼﾞに合わせて貼付けの事",
"P222のｴｯｼﾞ･ｾﾝﾀｰに合わせて貼付けの事",
"貼付け目... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部材",
"WorkItems": [
"1. BRACKET ~SPACER を次工程に払い出す",
"2. LABEL LABEL を次工程に払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表BRACKET :12.その他(添... | {
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りの員数がある事",
"Method": "目視",
"RecordMethod": "2LC-JG-22006",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認①:『動作ｽｲｯﾁ設定』",
"WorkItems": [
"1. 装着ﾍｯﾄﾞの調整/ｷｬﾘﾌﾞが終了している事",
"2. ①『ﾎｰﾑ』を選択する",
"3. ②『ｻｰﾋﾞｽｴﾝｼﾞﾆｱ』をONにする",
"4. ③『動作ｽｲｯﾁ』を選択",
"5. ④『荷重ﾁｪｯｶｰF･R』､『実負荷(分銅)校正機能』を選択",
"6. ①『ﾎｰﾑ』を選択し⑤『はい』を選択",
"7.... | {
"QualityItem": "操作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "-",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認②:『ｷｬﾘﾌﾞﾚｰｼｮﾝ』",
"WorkItems": [
"3. ③『荷重ﾁｪｯｶｰ』を選択",
"1. ①『ｷｬﾘﾌﾞﾚｰｼｮﾝ』を選択",
"2. ②『第4工程』を選択",
"4. ④『荷重ﾁｪｯｶｰ位置測定』を選択する",
"5. 指定されたﾉｽﾞﾙを準備･ｾｯﾄし⑤を選択する",
"6. ⑥『正常に終了しました』の表示が出ていることを確認",
"7. ⑦『ﾒﾝﾃ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認③:『出力荷重確認1』",
"WorkItems": [
"1. ①『調整』を選択",
"2. ②『荷重ﾁｪｯｶｰ』を選択",
"3. ③『実荷重計測』を選択",
"4. ④『ｼﾞｸﾞ取付け』を選択",
"5. ｻﾎﾟｰﾄ治具をｾｯﾄし⑤『確認』を選択"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合はACTIVATIONｽｲｯﾁを押しながら... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認④:『出力荷重確認2』",
"WorkItems": [
"1. 計測する①『分銅』を選択し､②『計測ｽﾀｰﾄ』を選択する",
"2. 分銅を取付③『実行』を選択する",
"3. 分銅を取外し④『確認』を選択",
"4. ①『分銅』→1N､5Nそれぞれ②~④を実施"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合はACTIVATIONｽｲｯﾁを押しなが... | {
"QualityItem": "荷重確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "0.5N:±0.11.0N:±0.15.0N:±0.3",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認⑤:『動作確認1』",
"WorkItems": [
"1. ①｢機種切替｣を選択",
"2. ②｢生産ﾃﾞｰﾀ選択｣を選択",
"3. 下記注記が表示されるので③｢確認｣を選択",
"4. ④｢簡易ﾃﾞｰﾀ生成｣を選択",
"5. ⑤｢ｵﾌｾｯﾄ反映｣を選択",
"6. ⑥『1005』を選択",
"7. ⑦『ﾉｽﾞﾙ種別230､1001』を選択",
"8. ⑧｢読... | {
"QualityItem": "操作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認⑥:『動作確認2』",
"WorkItems": [
"1. ①『ﾍｯﾄﾞ』を選択する",
"2. ②で指定されたﾉｽﾞﾙを準備する",
"3. ﾁｪﾝｼﾞｬｰにﾉｽﾞﾙをｾｯﾄしﾏｼﾝにｾｯﾄする",
"4. ③『交換』を選択する"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合はACTIVATIONｽｲｯﾁを押しながらﾎﾞﾀﾝをﾀｯﾌﾟする",
... | {
"QualityItem": "操作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "(ｵﾌﾟｼｮﾝ)装着荷重計測ﾕﾆｯﾄ確認⑦:『動作確認3』",
"WorkItems": [
"1. ①『ﾒﾝﾃﾅﾝｽ』を選択する",
"2. ②『ﾍｯﾄﾞ』を選択する",
"6. ⑥NGになっていないことの確認",
"3. ③『装着荷重計測』を選択する",
"4. ④『全選択』を選択する",
"5. ⑤『計測ｽﾀｰﾄ』を選択する",
"7. 確認後､ﾉｽﾞﾙを外す"
],
"WorkPoints": ... | {
"QualityItem": "荷重確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "警告値における上限値・下限値以内であること",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付け",
"WorkItems": [
"1. にLABEL を貼付ける"
],
"WorkPoints": [
"｢Model No.｣が､ ｢MTKU000044AD｣ になっている事",
"枠内からはみ出したり斜めにならないようにすること",
"ｼﾘｱﾙﾅﾝﾊﾞｰの確認をすること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "+№1",
"ToolOther": "40cN･m",
"WorkName": "ｸﾗﾝﾊﾟｰ取付け1",
"WorkItems": [
"◆1. にHOLDER KIT PLATE SPRING をSCREW で取付ける"
],
"WorkPoints": [
"HOLDER KIT PLATE の方向に注意",
"打ち抜き面をｽﾌﾟﾘﾝｸﾞ側(下側)にすること",
"HOLDER KIT の凸部が の溝に確実に入っているか確認する",
"SPRING PLATE... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾊﾟｰ取付け1",
"WorkItems": [
"◆1. にHOLDER KIT PLATE SPRING をSCREW で取付ける"
],
"WorkPoints": [
"HOLDER KIT PLATE の方向に注意",
"打ち抜き面をｽﾌﾟﾘﾝｸﾞ側(下側)にすること",
"HOLDER KIT の凸部が の溝に確実に入っているか確認する",
"SPRING PLATE HOLDER KIT を台に置く(... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｸﾗﾝﾌﾟｷｯﾄﾊﾞﾈ圧縮取付けｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5336",
"WorkName": "ｸﾗﾝﾊﾟｰ取付け1",
"WorkItems": [
"◆1. にHOLDER KIT PLATE SPRING をSCREW で取付ける"
],
"WorkPoints": [
"HOLDER KIT PLATE の方向に注意",
"打ち抜き面をｽﾌﾟﾘﾝｸﾞ側(下側)にすること",
"HOLDER KIT の凸部が の溝に確実に入っているか確認する",
"SPRI... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5336",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "-4.5㎜",
"ToolOther": "60cN･m",
"WorkName": "ﾃｰﾌﾟｶﾞｲﾄﾞ押さえﾚﾊﾞｰ取付け",
"WorkItems": [
"◆1. にSPACER SPRING を取付ける",
"3. BOLT を取付ける"
],
"WorkPoints": [
"SPACER の凸部を挿入"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟｶﾞｲﾄﾞ押さえﾚﾊﾞｰ取付け",
"WorkItems": [
"◆1. にSPACER SPRING を取付ける",
"◆2. を上からｽﾗｲﾄﾞさせてNUT を取付ける",
"3. BOLT を取付ける"
],
"WorkPoints": [
"両内側と穴の中",
"SPACER の凸部を挿入",
"NUT が の穴に入るところまで挿入",
"ｶﾊﾞｰ押さえを指で押し離した後､途中で引... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:1米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟｶﾞｲﾄﾞ押さえﾚﾊﾞｰ取付け",
"WorkItems": [
"◆1. にSPACER SPRING を取付ける",
"◆2. を上からｽﾗｲﾄﾞさせてNUT を取付ける",
"3. BOLT を取付ける"
],
"WorkPoints": [
"両内側と穴の中",
"SPACER の凸部を挿入",
"NUT が の穴に入るところまで挿入",
"ｶﾊﾞｰ押さえを指で押し離した後､途中で引... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WDKC-G09-001",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "7㎜幅",
"ToolOther": "80cN･m",
"WorkName": "ｸﾗﾝﾊﾟｰ取付け2",
"WorkItems": [
"◆1. にCLAMPER KIT をPIN で取付ける",
"◆2. PIN を取付ける"
],
"WorkPoints": [
"溝にかみ合わせる事",
"斜めになってなく左右均等に取付いていること"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m",
"締付ﾄﾙｸ 100cN･m"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "100cN･m",
"WorkName": "ｸﾗﾝﾊﾟｰ取付け2",
"WorkItems": [
"◆1. にCLAMPER KIT をPIN で取付ける",
"◆2. PIN を取付ける"
],
"WorkPoints": [
"溝にかみ合わせる事",
"斜めになってなく左右均等に取付いていること"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m",
"締付ﾄﾙｸ 100cN･m"
]... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾊﾟｰ取付け2",
"WorkItems": [
"◆1. にCLAMPER KIT をPIN で取付ける",
"◆2. PIN を取付ける"
],
"WorkPoints": [
"溝にかみ合わせる事",
"斜めになってなく左右均等に取付いていること"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m",
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo":... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾊﾟｰ取付け2",
"WorkItems": [
"◆1. にCLAMPER KIT をPIN で取付ける",
"◆2. PIN を取付ける"
],
"WorkPoints": [
"溝にかみ合わせる事",
"斜めになってなく左右均等に取付いていること"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m",
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo":... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:1ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ALﾌｨｰﾀﾞﾅｯﾄ落下防止治具",
"Size": "",
"ToolOther": "FM-4409",
"WorkName": "ﾅｯﾄｾｯﾄ",
"WorkItems": [
"1. NUT を に入れて㉖をスライドさせセットする"
],
"WorkPoints": [
"斜めに入っていないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4409",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "BOX5.5㎜",
"ToolOther": "80cN･m",
"WorkName": "ｸﾗﾝﾊﾟｰ部ﾅｯﾄ取付",
"WorkItems": [
"1. にNUT を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "15cN･m",
"WorkName": "ｽｲｯﾁ取付け",
"WorkItems": [
"1. にSWITCH をBOLT で取付ける"
],
"WorkPoints": [
"位置決め穴のｶﾞﾀ分､時計回り方向によせておく",
"配線は図のように上側に通す"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽｲｯﾁ取付け",
"WorkItems": [
"1. にSWITCH をBOLT で取付ける"
],
"WorkPoints": [
"位置決め穴のｶﾞﾀ分､時計回り方向によせておく",
"配線は図のように上側に通す"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes":... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "20cN･m",
"WorkName": "ｱｸﾁｭｴｰﾀｰ取付け",
"WorkItems": [
"1. に を挿入する",
"2. を にBOLT WASHER で取付を行う"
],
"WorkPoints": [
"向きに注意",
"｢SD-A00501-413｣で取り外したﾋﾟｽﾄﾝを取付ける",
" の凸部を の穴に合わせて取付けること"
],
"Tolks": [
"締付ﾄﾙｸ 20cN･... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｱｸﾁｭｴｰﾀｰ取付け",
"WorkItems": [
"1. に を挿入する",
"2. を にBOLT WASHER で取付を行う"
],
"WorkPoints": [
"向きに注意",
"｢SD-A00501-413｣で取り外したﾋﾟｽﾄﾝを取付ける",
" の凸部を の穴に合わせて取付けること"
],
"Tolks": [
"締付ﾄﾙｸ 20cN･m"
],
"Inspec... | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "噛み込み無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾏｲﾅｽ7㎜幅",
"ToolOther": "60cN･m",
"WorkName": "ｼｬｯﾀｰﾚﾊﾞｰ取付け",
"WorkItems": [
"1. に をPIN で取付ける",
"◆2. SPRING を取付ける",
"3. ➀を上下させて隙間、動きの確認を行う"
],
"WorkPoints": [
" の凸部に合わせて取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": ""... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰﾚﾊﾞｰ取付け",
"WorkItems": [
"1. に をPIN で取付ける",
"◆2. SPRING を取付ける",
"3. ➀を上下させて隙間、動きの確認を行う"
],
"WorkPoints": [
" の凸部に合わせて取付ける",
"引っかかりなくｽﾑｰｽﾞに上下するか確認する",
"ﾊﾞﾈ伸縮の妨げになる為､ｸﾞﾘｰｽをﾊﾞﾈ両端以外に塗布しないこと",
"自重で落下する事... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ALﾌｨｰﾀﾞﾅｯﾄ落下防止治具",
"Size": "",
"ToolOther": "FM-4409",
"WorkName": "ｼｬｯﾀｰﾚﾊﾞｰ取付け",
"WorkItems": [
"1. に をPIN で取付ける",
"◆2. SPRING を取付ける",
"3. ➀を上下させて隙間、動きの確認を行う"
],
"WorkPoints": [
" の凸部に合わせて取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": ""... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4409",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰﾚﾊﾞｰ取付け",
"WorkItems": [
"1. に をPIN で取付ける",
"◆2. SPRING を取付ける",
"3. ➀を上下させて隙間、動きの確認を行う"
],
"WorkPoints": [
" の凸部に合わせて取付ける",
"引っかかりなくｽﾑｰｽﾞに上下するか確認する",
"ﾊﾞﾈ伸縮の妨げになる為､ｸﾞﾘｰｽをﾊﾞﾈ両端以外に塗布しないこと",
"自重で落下する事... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "正常な事",
"Method": "目視",
"RecordMethod": "WDKC-G09-001",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "-幅4.5㎜",
"ToolOther": "60cN･m",
"WorkName": "落下防止ｷﾞｱ取付け",
"WorkItems": [
"◆1. に SPRING をPIN で取付ける",
"2. の動きの確認を行う"
],
"WorkPoints": [
"正回転方向のみに回転する事",
"ｽﾑｰｽﾞに回転する事",
"ｽﾑｰｽﾞに動作する事",
"SPRING のﾌｯｸの方向に注意",
"SPRING の両端､ の摺動面にｸﾞﾘｰｽ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "落下防止ｷﾞｱ取付け",
"WorkItems": [
"◆1. に SPRING をPIN で取付ける",
"2. の動きの確認を行う"
],
"WorkPoints": [
"正回転方向のみに回転する事",
"ｽﾑｰｽﾞに回転する事",
"ｽﾑｰｽﾞに動作する事",
"SPRING のﾌｯｸの方向に注意",
"SPRING の両端､ の摺動面にｸﾞﾘｰｽを塗布すること"
],
"To... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:1ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "落下防止ｷﾞｱ取付け",
"WorkItems": [
"◆1. に SPRING をPIN で取付ける",
"2. の動きの確認を行う"
],
"WorkPoints": [
"正回転方向のみに回転する事",
"ｽﾑｰｽﾞに回転する事",
"ｽﾑｰｽﾞに動作する事",
"SPRING のﾌｯｸの方向に注意",
"SPRING の両端､ の摺動面にｸﾞﾘｰｽを塗布すること"
],
"To... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "落下防止ｷﾞｱ取付け",
"WorkItems": [
"◆1. に SPRING をPIN で取付ける",
"2. の動きの確認を行う"
],
"WorkPoints": [
"正回転方向のみに回転する事",
"ｽﾑｰｽﾞに回転する事",
"ｽﾑｰｽﾞに動作する事",
"SPRING のﾌｯｸの方向に注意",
"SPRING の両端､ の摺動面にｸﾞﾘｰｽを塗布すること"
],
"To... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "正常な事",
"Method": "目視",
"RecordMethod": "WDKC-G09-001",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "-幅7㎜",
"ToolOther": "60cN･m",
"WorkName": "ﾚﾊﾞｰ取付け",
"WorkItems": [
"1. にCOLLAR をPIN で取付ける",
"2. ㉘を取り外す"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ALﾌｨｰﾀﾞﾅｯﾄ落下防止治具",
"Size": "",
"ToolOther": "FM-4409",
"WorkName": "ﾚﾊﾞｰ取付け",
"WorkItems": [
"1. にCOLLAR をPIN で取付ける",
"2. ㉘を取り外す",
"1. にCOLLAR をPIN で取付ける",
"2. ㉘を取り外す"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 60cN･m"
],
"Insp... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4409",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WDKC-G09-001",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾌﾟﾘﾝｸﾞ取付け1",
"WorkItems": [
"◆1. にSPRING SPRING を取付ける"
],
"WorkPoints": [
"ﾌｯｸの向きに注意",
"確実に溝に入っているか確認する事",
"ｽﾌﾟﾘﾝｸﾞﾌｯｸの外れ無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾌﾟﾘﾝｸﾞ取付け1",
"WorkItems": [
"◆1. にSPRING SPRING を取付ける"
],
"WorkPoints": [
"ﾌｯｸの向きに注意",
"確実に溝に入っているか確認する事",
"ｽﾌﾟﾘﾝｸﾞﾌｯｸの外れ無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WDKC-G09-001",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "#0",
"ToolOther": "17cN･m",
"WorkName": "ｾﾝｻ取付け2",
"WorkItems": [
"1. にSENSOR をSCREW WASHER で取付ける"
],
"WorkPoints": [
"SENSOR はﾊﾞｶ穴分上･右側に寄せて取付け",
"乗り上げ注意"
],
"Tolks": [
"締付ﾄﾙｸ 17cN･m"
],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "17cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻ取付け2",
"WorkItems": [
"1. にSENSOR をSCREW WASHER で取付ける",
"2. ㉘で配線を固定する"
],
"WorkPoints": [
"SENSOR はﾊﾞｶ穴分上･右側に寄せて取付け",
"乗り上げ注意",
"LEDが見える向きで取付ける",
"配線がﾌﾚｰﾑ側面がら飛び出さないようｶﾌﾟﾄﾝﾃｰﾌﾟで固定"
],
"Tolks": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻ取付け2",
"WorkItems": [
"1. にSENSOR をSCREW WASHER で取付ける",
"2. ㉘で配線を固定する"
],
"WorkPoints": [
"SENSOR はﾊﾞｶ穴分上･右側に寄せて取付け",
"乗り上げ注意",
"LEDが見える向きで取付ける",
"配線がﾌﾚｰﾑ側面がら飛び出さないようｶﾌﾟﾄﾝﾃｰﾌﾟで固定"
],
"Tolks": [
... | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "噛み込み無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.0",
"ToolOther": "15cN･m",
"WorkName": "ｽﾌﾟﾘﾝｸﾞ取付け2",
"WorkItems": [],
"WorkPoints": [
"ﾌﾚｰﾑの摺動面にｸﾞﾘｰｽを塗布する"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾌﾟﾘﾝｸﾞ取付け2",
"WorkItems": [
"◆1. PIN を㉙にセットし を倒す",
"◆2. SPRING をｾｯﾄしCOLLAR SCREW で取付け",
"3. ｽﾌﾟﾘﾝｸﾞのﾌｯｸをかける"
],
"WorkPoints": [
"㉙にPIN のマイナス溝を合わせてセットする事",
"SPRING の向きに注意",
"ﾌｯｸの方向に注意",
"ﾌﾚｰﾑの摺動面にｸﾞﾘｰｽを塗... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:1ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾈｼﾞ締付台",
"Size": "",
"ToolOther": "FM-4408",
"WorkName": "ｽﾌﾟﾘﾝｸﾞ取付け2",
"WorkItems": [],
"WorkPoints": [
"ﾌﾚｰﾑの摺動面にｸﾞﾘｰｽを塗布する",
"ﾌﾚｰﾑの摺動面にｸﾞﾘｰｽを塗布する"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTyp... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4408",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾌﾟﾘﾝｸﾞ取付け2",
"WorkItems": [
"◆1. PIN を㉙にセットし を倒す",
"◆2. SPRING をｾｯﾄしCOLLAR SCREW で取付け",
"3. ｽﾌﾟﾘﾝｸﾞのﾌｯｸをかける"
],
"WorkPoints": [
"㉙にPIN のマイナス溝を合わせてセットする事",
"SPRING の向きに注意",
"ﾌｯｸの方向に注意",
"ﾌﾚｰﾑの摺動面にｸﾞﾘｰｽを塗... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "正常な事",
"Method": "目視",
"RecordMethod": "WDKC-G09-001",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "40cN･m",
"WorkName": "ﾌﾞﾛｯｸ取付け",
"WorkItems": [
"1. にBLOCK をBOLT で取付ける"
],
"WorkPoints": [
"当付けて固定する"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｯｸ取付け",
"WorkItems": [
"1. にBLOCK をBOLT で取付ける"
],
"WorkPoints": [
"当付けて固定する"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "40cN･m",
"WorkName": "ｾﾝｻ取付け1",
"WorkItems": [
"1. にSENSOR ､COVER をSCREW で取付ける"
],
"WorkPoints": [
"配線のはさみこみ無きこと",
"ｶﾌﾟﾄﾝﾃｰﾌﾟを貼る配線のはさみこみ無きこと",
"COVER は上に押し当てながら締結のこと",
"SENSOR は㉘を使って位置決めをする事(2箇所)"
],
"Tolks": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "継ぎ目検出ｾﾝｻｰ位置決め治具",
"Size": "",
"ToolOther": "FM-4049",
"WorkName": "ｾﾝｻ取付け1",
"WorkItems": [
"1. にSENSOR ､COVER をSCREW で取付ける"
],
"WorkPoints": [
"配線のはさみこみ無きこと",
"ｶﾌﾟﾄﾝﾃｰﾌﾟを貼る配線のはさみこみ無きこと",
"COVER は上に押し当てながら締結のこと",
"SENSOR は㉘を使って位置決めをする事(2箇所)"
],
"Tolks"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4049",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾝｻ取付け1",
"WorkItems": [
"1. にSENSOR ､COVER をSCREW で取付ける"
],
"WorkPoints": [
"配線のはさみこみ無きこと",
"ｶﾌﾟﾄﾝﾃｰﾌﾟを貼る配線のはさみこみ無きこと",
"COVER は上に押し当てながら締結のこと",
"SENSOR は㉘を使って位置決めをする事(2箇所)"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･... | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "噛み込み無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "30cN･m",
"WorkName": "ﾄﾞﾗｲﾊﾞｰ基板取付け",
"WorkItems": [
"■★1. にSHEET MOTOR-DRIVER をSCREW で取付ける"
],
"WorkPoints": [
"白ｺﾈｸﾀが並んでいる側を上側にすること",
"SHEET は2枚重なっていてもわかりづらいので取付時､注意のこと",
"型式:MU001-8111-D"
],
"Tolks": [
"締付ﾄﾙ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾗｲﾊﾞｰ基板取付け",
"WorkItems": [
"■★1. にSHEET MOTOR-DRIVER をSCREW で取付ける"
],
"WorkPoints": [
"白ｺﾈｸﾀが並んでいる側を上側にすること",
"SHEET は2枚重なっていてもわかりづらいので取付時､注意のこと",
"型式:MU001-8111-D"
],
"Tolks": [
"締付ﾄﾙｸ 30cN･m"
],
... | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示された型式になっている事",
"Method": "目視",
"RecordMethod": "WDKC-G09-001",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線",
"WorkItems": [
"★1. 基盤に配線を接続する",
"2. ｹｰﾌﾞﾙをとめる"
],
"WorkPoints": [
"ｺﾈｸﾀの向きに注意",
"ｺﾈｸﾀの向きに注意",
"空き",
"1→2→3の順番に接続して配線の負荷がかからないようにすること",
"ｺﾈｸﾀを接続したら青ﾏｰｷﾝｸﾞをする"
],
"Tolks": [],
"InspectionNo"... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線",
"WorkItems": [
"★1. 基盤に配線を接続する",
"2. ｹｰﾌﾞﾙをとめる"
],
"WorkPoints": [
"ｺﾈｸﾀの向きに注意",
"ｺﾈｸﾀの向きに注意",
"空き",
"1→2→3の順番に接続して配線の負荷がかからないようにすること",
"ｺﾈｸﾀを接続したら青ﾏｰｷﾝｸﾞをする"
],
"Tolks": [],
"InspectionNo"... | {
"QualityItem": "負荷確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｹｰﾌﾞﾙに負荷がかかって無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "送りﾓｰﾀｰ・ｻｲﾄﾞﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. にMOTOR をBOLT で取付け､PLATE をSCREW BOLT で取付ける"
],
"WorkPoints": [
"ﾓｰﾀのｹｰﾌﾞﾙは下図のように通すこと",
"ｻｲﾄﾞﾌﾟﾚｰﾄとﾌﾚｰﾑの段差を手感で確認しﾌﾚｰﾑと同じ高さ或いはﾌﾚｰﾑより出ていないこと",
"㉜を に押し当てクランプをロックす... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "40cN･m",
"WorkName": "送りﾓｰﾀｰ・ｻｲﾄﾞﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. にMOTOR をBOLT で取付け､PLATE をSCREW BOLT で取付ける"
],
"WorkPoints": [
"ﾓｰﾀのｹｰﾌﾞﾙは下図のように通すこと",
"ｻｲﾄﾞﾌﾟﾚｰﾄとﾌﾚｰﾑの段差を手感で確認しﾌﾚｰﾑと同じ高さ或いはﾌﾚｰﾑより出ていないこと",
"㉜を に押し当てクランプをロックする... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "送りﾓｰﾀｰ・ｻｲﾄﾞﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. にMOTOR をBOLT で取付け､PLATE をSCREW BOLT で取付ける"
],
"WorkPoints": [
"ﾓｰﾀのｹｰﾌﾞﾙは下図のように通すこと",
"ｻｲﾄﾞﾌﾟﾚｰﾄとﾌﾚｰﾑの段差を手感で確認しﾌﾚｰﾑと同じ高さ或いはﾌﾚｰﾑより出ていないこと",
"㉜を に押し当てクランプをロックす... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "8cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾟﾚｰﾄ走行面合わせ治具",
"Size": "",
"ToolOther": "FM-4417",
"WorkName": "送りﾓｰﾀｰ・ｻｲﾄﾞﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. にMOTOR をBOLT で取付け､PLATE をSCREW BOLT で取付ける"
],
"WorkPoints": [
"ﾓｰﾀのｹｰﾌﾞﾙは下図のように通すこと",
"ｻｲﾄﾞﾌﾟﾚｰﾄとﾌﾚｰﾑの段差を手感で確認しﾌﾚｰﾑと同じ高さ或いはﾌﾚｰﾑより出ていないこと",
"㉜を に押し当てクランプをロックする... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4417",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WDKC-G09-001",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "引き込みﾓｰﾀｰ取付け1",
"WorkItems": [
"1. にMOTOR をBOLT で取付ける"
],
"WorkPoints": [
"裏面の写真",
"樹脂ｶﾞｲﾄﾞでMOTOR の歯が隠れている事",
"ｹｰﾌﾞﾙを先に入れる",
"ﾓｰﾀのﾋﾟﾝをﾌﾚｰﾑの穴に入れること",
"➀を入れる時に、➀のスプロケットが樹脂ガイドに乗り上げるためこの樹脂ガイドを... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "引き込みﾓｰﾀｰ取付け1",
"WorkItems": [
"1. にMOTOR をBOLT で取付ける"
],
"WorkPoints": [
"裏面の写真",
"樹脂ｶﾞｲﾄﾞでMOTOR の歯が隠れている事",
"ｹｰﾌﾞﾙを先に入れる",
"ﾓｰﾀのﾋﾟﾝをﾌﾚｰﾑの穴に入れること",
"➀を入れる時に、➀のスプロケットが樹脂ガイドに乗り上げるためこの樹脂ガイドを下げながら取付のこと"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "30cN･m",
"WorkName": "引き込みﾓｰﾀｰ取付け2",
"WorkItems": [
"1. にSCREW を取付ける"
],
"WorkPoints": [
"先にｾﾝｻｰのｺﾈｸﾀを挿して青ﾏｰｷﾝｸﾞ",
"ﾈｼﾞを締めた後で､配線をｶﾌﾟﾄﾝﾃｰﾌﾟで固定する",
"配線経路に押し込むようにﾃｰﾌﾟでとめる"
],
"Tolks": [
"締付ﾄﾙｸ 30cN･m"
],
"I... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "引き込みﾓｰﾀｰ取付け2",
"WorkItems": [
"1. にSCREW を取付ける"
],
"WorkPoints": [
"先にｾﾝｻｰのｺﾈｸﾀを挿して青ﾏｰｷﾝｸﾞ",
"ﾈｼﾞを締めた後で､配線をｶﾌﾟﾄﾝﾃｰﾌﾟで固定する",
"配線経路に押し込むようにﾃｰﾌﾟでとめる"
],
"Tolks": [
"締付ﾄﾙｸ 30cN･m"
],
"InspectionNo": "",
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "引き込みﾓｰﾀｰ取付け2",
"WorkItems": [
"1. にSCREW を取付ける"
],
"WorkPoints": [
"先にｾﾝｻｰのｺﾈｸﾀを挿して青ﾏｰｷﾝｸﾞ",
"ﾈｼﾞを締めた後で､配線をｶﾌﾟﾄﾝﾃｰﾌﾟで固定する",
"配線経路に押し込むようにﾃｰﾌﾟでとめる"
],
"Tolks": [
"締付ﾄﾙｸ 30cN･m"
],
"InspectionNo": "",
... | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "噛み込み無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.