input stringclasses 1 value | instruction stringlengths 222 1.92k | output stringlengths 193 312 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "HEPA(OP)配線③",
"WorkItems": [
"■1. ｱｰｽ線をSCREW でｱｰｽ板に取付ける",
"2. HEPA電源ﾕﾆｯﾄを固定する"
],
"WorkPoints": [
"ｱｰｽ版取付け後 電源ﾕﾆｯﾄを固定する",
"HEPA(OP)が有る場合実施する"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :端子台接続確認",
"4X006",
"6X006",
"8X006",
"2X006",
"WWYJ-5300-101"
]
} | {
"QualityItem": "端子台接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-101",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "HEPA(OP)配線③",
"WorkItems": [
"■1. ｱｰｽ線をSCREW でｱｰｽ板に取付ける"
],
"WorkPoints": [
"HEPA(OP)が有る場合実施する"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :端子台接続確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "HEPA(OP)配線④",
"WorkItems": [
"1. HEPAの配線をする"
],
"WorkPoints": [
"HEPA(OP)がある時に実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ｺﾈｸﾀ接続確認",
"1G10720-1R",
"1G10720-2R",
"1G10720-3R",
"1G10720-4R",
"(Dummy)",
"(Dummy)",
"(Dummy)",
"(Dummy)",
"1G10720R",
"WWYJ-5300-104"
]
} | {
"QualityItem": "ｺﾈｸﾀｰ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-104",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "HEPA(OP)配線⑤",
"WorkItems": [
"■1. HEPA配線を接続し整線する"
],
"WorkPoints": [
"HEPA(OP)がある時に実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN16K007",
"CN15K007",
"ADPW-01",
"ADPW-02",
"ADPW-03",
"ADPW-04",
"ADPW-12",
"ADPW-13",
"ADPW-14",
"ADPW-15",
"検査表 :ｺﾈｸﾀ接続確認",
"検査表 :端子接続確認",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WWYJ-5300-101"
]
} | {
"QualityItem": "ｺﾈｸﾀｰ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-101",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "HEPA(OP)配線⑤",
"WorkItems": [
"■1. HEPA配線を接続し整線する"
],
"WorkPoints": [
"HEPA(OP)がある時に実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN16K007",
"CN15K007",
"ADPW-01",
"ADPW-02",
"ADPW-03",
"ADPW-04",
"ADPW-12",
"ADPW-13",
"ADPW-14",
"ADPW-15",
"検査表 :ｺﾈｸﾀ接続確認",
"検査表 :端子接続確認",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WWYJ-5300-101"
]
} | {
"QualityItem": "端子台接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-101",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄUPPER2組立",
"WorkItems": [],
"WorkPoints": [
"SUPPORT はNUT NUT とｾｯﾄで使用",
"BRACKET BRACKET はFRAME と端面合わせ",
"BRACKET BRACKET はFRAME と端面合わせ",
"BRACKET BRACKET はFRAME と端面合わせ",
"･は止めﾈｼﾞの方向を示す"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"NUT N004:M6止めﾈｼﾞ付き",
"CABLE-SUPPORT N007"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "ﾌﾚｰﾑｷｯﾄUPPER2組立",
"WorkItems": [],
"WorkPoints": [
"SUPPORT はNUT NUT とｾｯﾄで使用",
"BRACKET BRACKET はFRAME と端面合わせ",
"BRACKET BRACKET はFRAME と端面合わせ",
"BRACKET BRACKET はFRAME と端面合わせ",
"･は止めﾈｼﾞの方向を示す"
],
"Tolks": [
"締付ﾄﾙｸ11.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"NUT N004:M6止めﾈｼﾞ付き",
"CABLE-SUPPORT N007"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け_1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに貼付けてある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"1. 1.VALVE にJOINT SILENCER JOINT を取付",
"2. JOINT へTUBE を取付"
],
"WorkPoints": [
"ｼｰﾙ材のかすはﾋﾟﾝｾｯﾄ等で取り除くこと｡ｴｱｰﾌﾞﾛｰではｼﾞｮｲﾝﾄに入り込にﾊﾞﾙﾌﾞ破損に繋がります｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付ﾄﾙｸ 120cN･m",
"JOINT ",
"JOINT ",
"SILENCER ",
"VALVE ",
"120cN･m",
"3mm",
"3mm",
"JOINT ",
"TUBE ",
"手締めのことの"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "120cN･m",
"WorkName": "ﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"1. 1.VALVE にJOINT SILENCER JOINT を取付",
"2. JOINT へTUBE を取付"
],
"WorkPoints": [
"ｼｰﾙ材のかすはﾋﾟﾝｾｯﾄ等で取り除くこと｡ｴｱｰﾌﾞﾛｰではｼﾞｮｲﾝﾄに入り込にﾊﾞﾙﾌﾞ破損に繋がります｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付ﾄﾙｸ 120cN･m",
"JOINT ",
"JOINT ",
"SILENCER ",
"VALVE ",
"120cN･m",
"3mm",
"3mm",
"JOINT ",
"TUBE ",
"手締めのことの"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2N・m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"1. 1.VALVE にJOINT SILENCER JOINT を取付",
"2. JOINT へTUBE を取付"
],
"WorkPoints": [
"ｼｰﾙ材のかすはﾋﾟﾝｾｯﾄ等で取り除くこと｡ｴｱｰﾌﾞﾛｰではｼﾞｮｲﾝﾄに入り込にﾊﾞﾙﾌﾞ破損に繋がります｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付ﾄﾙｸ 120cN･m",
"JOINT ",
"JOINT ",
"SILENCER ",
"VALVE ",
"120cN･m",
"3mm",
"3mm",
"JOINT ",
"TUBE ",
"手締めのことの"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りに接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｼﾘﾝﾀﾞ部組立(1/4)",
"WorkItems": [
"1. BLOCK にSPACER BEARING をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｼﾘﾝﾀﾞ部組立(2/4)",
"WorkItems": [
"2. CYLINDER(300MM) の付属ﾅｯﾄを 取り外す",
"◆3. WASHER GUIDE WASHER SPRING にｸﾞﾘｰｽを塗布する",
"1. CYLINDER(300MM) にSPACER をBOLT で取付け"
],
"WorkPoints": [
"組込む前に塗布すること",
"治具の両面がﾜｯｼｬとﾎﾞﾙﾄに接触した状態で負荷なく治具の抜き差しが可能な状態とする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業",
"締付ﾄﾙｸ 95cN･m",
"全体にｸﾞﾘｰｽ塗布 米粒:1"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾘﾝﾀﾞ部組立(2/4)",
"WorkItems": [
"2. CYLINDER(300MM) の付属ﾅｯﾄを 取り外す",
"4. CYLINDER(300MM) にWASHER GUIDE WASHER SPRING 付属ﾅｯﾄを入れる",
"5. を取付",
"6. ｼﾘﾝﾀﾞのｽﾄﾛｰｸを調整 付属ﾅｯﾄで固定する",
"◆3. WASHER GUIDE WASHER SPRING にｸﾞﾘｰｽを塗布する",
"1. CYLINDER(300MM) にSPACER をBOLT で取付け"
],
"WorkPoints": [
"組込む前に塗布すること",
"※ ｽﾌﾟﾘﾝｸﾞを 飛ばさないように注意",
"FM-3087が入ること",
"治具の両面がﾜｯｼｬとﾎﾞﾙﾄに接触した状態で負荷なく治具の抜き差しが可能な状態とする",
"ｼﾘﾝﾀﾞｰ作業台上に密着させる事",
"しっかりと固定する事(ｽﾊﾟﾅは回転させない)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業",
"GUIDE ",
"WASHER ",
"SPRING ",
"付属ﾅｯﾄ",
"WASHER ",
"締付ﾄﾙｸ 95cN･m",
"SPACER ",
"締付けﾄﾙｸ:1.2N･m",
"CYLINDER(300MM) ",
"付属ﾅｯﾄ",
"検査表WASHER :ｼﾘﾝﾀﾞｰ調整 ｽﾄﾛｰｸ調整､位置調整",
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 米粒:1",
"全体にｸﾞﾘｰｽ塗布 米粒:1",
"0.10mmのｼｯｸﾈｽｹﾞｰｼﾞが入らないこと"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒/2粒米粒/1粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼﾘﾝﾀﾞｰﾌﾞﾛｯｸ保持治具",
"Size": "",
"ToolOther": "FM-3087",
"WorkName": "ｼﾘﾝﾀﾞ部組立(2/4)",
"WorkItems": [
"4. CYLINDER(300MM) にWASHER GUIDE WASHER SPRING 付属ﾅｯﾄを入れる",
"5. を取付",
"6. ｼﾘﾝﾀﾞのｽﾄﾛｰｸを調整 付属ﾅｯﾄで固定する"
],
"WorkPoints": [
"※ ｽﾌﾟﾘﾝｸﾞを 飛ばさないように注意",
"FM-3087が入ること",
"ｼﾘﾝﾀﾞｰ作業台上に密着させる事",
"しっかりと固定する事(ｽﾊﾟﾅは回転させない)"
],
"Tolks": [],
"InspectionNo": "WDQB-F013-006",
"InspectionItems": [
"検査表WASHER :ｼﾘﾝﾀﾞｰ調整 ｽﾄﾛｰｸ調整､位置調整"
],
"WorkTypes": [],
"Words": [
"締付けﾄﾙｸ:1.2N･m",
"0.10mmのｼｯｸﾈｽｹﾞｰｼﾞが入らないこと",
"WDQB-F013-006"
]
} | {
"QualityItem": "ｼﾘﾝﾀﾞｰ調整",
"ToolManageNo": "FM-3087",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "16.0±0.1㎜",
"Method": "目視",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "5.5㎜",
"ToolOther": "1.2N･m",
"WorkName": "ｼﾘﾝﾀﾞ部組立(2/4)",
"WorkItems": [
"4. CYLINDER(300MM) にWASHER GUIDE WASHER SPRING 付属ﾅｯﾄを入れる",
"5. を取付",
"6. ｼﾘﾝﾀﾞのｽﾄﾛｰｸを調整 付属ﾅｯﾄで固定する"
],
"WorkPoints": [
"※ ｽﾌﾟﾘﾝｸﾞを 飛ばさないように注意",
"FM-3087が入ること",
"ｼﾘﾝﾀﾞｰ作業台上に密着させる事",
"しっかりと固定する事(ｽﾊﾟﾅは回転させない)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付けﾄﾙｸ:1.2N･m",
"検査表WASHER :ｼﾘﾝﾀﾞｰ調整 ｽﾄﾛｰｸ調整､位置調整",
"0.10mmのｼｯｸﾈｽｹﾞｰｼﾞが入らないこと"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾘﾝﾀﾞ部組立(2/4)",
"WorkItems": [
"2. CYLINDER(300MM) の付属ﾅｯﾄを 取り外す",
"4. CYLINDER(300MM) にWASHER GUIDE WASHER SPRING 付属ﾅｯﾄを入れる",
"5. を取付",
"6. ｼﾘﾝﾀﾞのｽﾄﾛｰｸを調整 付属ﾅｯﾄで固定する",
"◆3. WASHER GUIDE WASHER SPRING にｸﾞﾘｰｽを塗布する",
"1. CYLINDER(300MM) にSPACER をBOLT で取付け"
],
"WorkPoints": [
"組込む前に塗布すること",
"※ ｽﾌﾟﾘﾝｸﾞを 飛ばさないように注意",
"FM-3087が入ること",
"治具の両面がﾜｯｼｬとﾎﾞﾙﾄに接触した状態で負荷なく治具の抜き差しが可能な状態とする",
"ｼﾘﾝﾀﾞｰ作業台上に密着させる事",
"しっかりと固定する事(ｽﾊﾟﾅは回転させない)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業",
"GUIDE ",
"WASHER ",
"SPRING ",
"付属ﾅｯﾄ",
"WASHER ",
"締付ﾄﾙｸ 95cN･m",
"SPACER ",
"締付けﾄﾙｸ:1.2N･m",
"CYLINDER(300MM) ",
"付属ﾅｯﾄ",
"検査表WASHER :ｼﾘﾝﾀﾞｰ調整 ｽﾄﾛｰｸ調整､位置調整",
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 米粒:1",
"全体にｸﾞﾘｰｽ塗布 米粒:1",
"0.10mmのｼｯｸﾈｽｹﾞｰｼﾞが入らないこと"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.10㎜のｼｯｸﾈｽｹﾞｰｼﾞが入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "位置合わせ治具",
"Size": "",
"ToolOther": "FM-6131",
"WorkName": "ｼﾘﾝﾀﾞ部組立(3/4)",
"WorkItems": [
"1. にPLATE BLOCK をBOLT WASHER で仮固定",
"2. 1完成品を㉛に装着し締結する"
],
"WorkPoints": [
"PLATE を治具の段差部に乗せる",
"治具とｽｷﾏ無きよう当付ける",
" やPLATE の中央部を下方向に当付ける",
"押さえた指はそのままで、㉖と㉗で締結する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付けﾄﾙｸ: 95cN･m"
]
} | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-6131",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｼﾘﾝﾀﾞ部組立(3/4)",
"WorkItems": [
"1. にPLATE BLOCK をBOLT WASHER で仮固定",
"2. 1完成品を㉛に装着し締結する"
],
"WorkPoints": [
"PLATE を治具の段差部に乗せる",
"治具とｽｷﾏ無きよう当付ける",
" やPLATE の中央部を下方向に当付ける",
"押さえた指はそのままで、㉖と㉗で締結する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付けﾄﾙｸ: 95cN･m"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "位置合わせ治具",
"Size": "",
"ToolOther": "FM-6131",
"WorkName": "ｼﾘﾝﾀﾞ部組立(4/4)",
"WorkItems": [
"1. に②を取付",
"2. 出限(B02/12R)のｺﾈｸﾀｰにPHﾁｪｯｶｰを繋ぎ ｼﾘﾝﾀﾞｰを伸ばしON領域とLS調整位置にﾏｰｷﾝｸﾞする",
"3. 戻限(B01/11R)のｺﾈｸﾀｰにPHﾁｪｯｶｰを繋ぎ ｼﾘﾝﾀﾞｰをちじめON領域とLS調整位置にﾏｰｷﾝｸﾞする",
"4. 各ｾﾝｻｰをLS調整位置へ固定する"
],
"WorkPoints": [
"出限･戻り限の取付位置(下図参照)を間違わないこと",
"右図を参照のこと",
"右図を参照のこと"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ｼﾘﾝﾀﾞｰLS位置調整",
"(出限)",
"(戻限)",
"検査表 :ｼﾘﾝﾀﾞｰLS位置調整",
"取付方向確認側面にｼﾞｮｲﾝﾄ取付穴有",
"出限",
"戻限",
"ｾﾝﾀｰ",
"⇧ＬＳ調整位置",
"約3㎜",
"右側より近づけてONする位置",
"左側より近づけてONする位置",
"右側より近づけてONする位置",
"左側より近づけてONする位置",
"ＬＳ調整位置⇩",
"約3㎜",
"ｾﾝﾀｰ",
"ｺﾈｸﾀｰへ",
"ﾏｰｷﾝｸﾞをする",
"ｼﾘﾝﾀﾞｰ戻限用LS(B01/11R)",
"ｼﾘﾝﾀﾞｰ出限用LS(B02/12R)"
]
} | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-6131",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2375",
"WorkName": "ｼﾘﾝﾀﾞ部組立(4/4)",
"WorkItems": [
"1. に②を取付",
"2. 出限(B02/12R)のｺﾈｸﾀｰにPHﾁｪｯｶｰを繋ぎ ｼﾘﾝﾀﾞｰを伸ばしON領域とLS調整位置にﾏｰｷﾝｸﾞする",
"3. 戻限(B01/11R)のｺﾈｸﾀｰにPHﾁｪｯｶｰを繋ぎ ｼﾘﾝﾀﾞｰをちじめON領域とLS調整位置にﾏｰｷﾝｸﾞする",
"4. 各ｾﾝｻｰをLS調整位置へ固定する"
],
"WorkPoints": [
"出限･戻り限の取付位置(下図参照)を間違わないこと",
"右図を参照のこと",
"右図を参照のこと"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ｼﾘﾝﾀﾞｰLS位置調整",
"(出限)",
"検査表 :ｼﾘﾝﾀﾞｰLS位置調整",
"(戻限)",
"WDQB-F013-006"
]
} | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-2375",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り取付いている事",
"Method": "PHﾁｪｯｶｰ",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾏｲﾅｽ1.6㎜",
"ToolOther": "10cN･m",
"WorkName": "ｼﾘﾝﾀﾞ部組立(4/4)",
"WorkItems": [
"3. 戻限(B01/11R)のｺﾈｸﾀｰにPHﾁｪｯｶｰを繋ぎ ｼﾘﾝﾀﾞｰをちじめON領域とLS調整位置にﾏｰｷﾝｸﾞする",
"4. 各ｾﾝｻｰをLS調整位置へ固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"(戻限)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾘﾝﾀﾞ部組立(4/4)",
"WorkItems": [
"1. に②を取付",
"2. 出限(B02/12R)のｺﾈｸﾀｰにPHﾁｪｯｶｰを繋ぎ ｼﾘﾝﾀﾞｰを伸ばしON領域とLS調整位置にﾏｰｷﾝｸﾞする",
"3. 戻限(B01/11R)のｺﾈｸﾀｰにPHﾁｪｯｶｰを繋ぎ ｼﾘﾝﾀﾞｰをちじめON領域とLS調整位置にﾏｰｷﾝｸﾞする",
"4. 各ｾﾝｻｰをLS調整位置へ固定する"
],
"WorkPoints": [
"出限･戻り限の取付位置(下図参照)を間違わないこと",
"右図を参照のこと",
"右図を参照のこと"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ｼﾘﾝﾀﾞｰLS位置調整",
"(出限)",
"(戻限)",
"検査表 :ｼﾘﾝﾀﾞｰLS位置調整",
"取付方向確認側面にｼﾞｮｲﾝﾄ取付穴有",
"出限",
"戻限",
"ｾﾝﾀｰ",
"⇧ＬＳ調整位置",
"約3㎜",
"右側より近づけてONする位置",
"左側より近づけてONする位置",
"右側より近づけてONする位置",
"左側より近づけてONする位置",
"ＬＳ調整位置⇩",
"約3㎜",
"ｾﾝﾀｰ",
"ｺﾈｸﾀｰへ",
"ﾏｰｷﾝｸﾞをする",
"ｼﾘﾝﾀﾞｰ戻限用LS(B01/11R)",
"ｼﾘﾝﾀﾞｰ出限用LS(B02/12R)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2N・m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾗｹｯﾄﾋﾟﾝ圧入治具ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "LEVER部組立(1/4)P005ﾌﾞﾛｯｸへﾋﾟﾝ圧入",
"WorkItems": [
"1. BRACKET の赤の指示部に油砥石をかける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. BRACKET をPIN に挿入し油砥石をかけた部分に防錆油を塗布する",
"ﾋﾟﾝ出代:3.5mm",
"S-Pinの割り部分をこちら側へ",
"3.5mm"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LEVER部組立(2/4)",
"WorkItems": [
"1. PLATE LEVER に砥石をかける",
"◆2. WASHER にｸﾞﾘｰｽを塗布する",
"3. LEVER にWASHER を入れる",
"4. PLATE にLEVER を合わせる",
"5. ④BOLT を取付",
"6. BOLT を取付"
],
"WorkPoints": [
"両面に砥石"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"PLATE ",
"LEVER ",
"締付けﾄﾙｸ: 320cN･m",
"締付けﾄﾙｸ: 150cN･m",
"WASHER ",
"BOLT ",
"WASHER ",
"LEVER ",
"PLATE ",
"WASHER ",
"BOLT ",
"･外周にｸﾞﾘｰｽ塗布米粒:2"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒/2粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "320cN･m",
"WorkName": "LEVER部組立(2/4)",
"WorkItems": [
"3. LEVER にWASHER を入れる",
"4. PLATE にLEVER を合わせる",
"5. ④BOLT を取付",
"6. BOLT を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付けﾄﾙｸ: 320cN･m",
"締付けﾄﾙｸ: 150cN･m",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%320cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "320cN･m",
"WorkName": "LEVER部組立(3/4)",
"WorkItems": [
"2. へ をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付けﾄﾙｸ: 3.2N･m",
"BOLT "
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "200cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LEVER部組立(4/4)",
"WorkItems": [
"1. LEVER に砥石をかける",
"5. BOLT にWASHER SPRING WASHER の順番で通す",
"◆4. BOLT にｸﾞﾘｰｽを塗布",
"3. にLEVER をBUSH WASHER BOLT で取付",
"◆2. BUSH にｸﾞﾘｰｽを塗布する",
"6. にBOLT を入れる"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"BUSH ",
"LEVER ",
"WASHER BOLT ",
"BUSH ",
"BOLT ",
"WASHER ",
"WASHER ",
"SPRING ",
"LCG100",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m",
"･摺動面にｸﾞﾘｰｽ塗布 米粒:2",
"･切削面にｸﾞﾘｰｽ塗布 米粒:2"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒/2粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "320cN･m",
"WorkName": "LEVER部組立(4/4)",
"WorkItems": [
"1. LEVER に砥石をかける",
"3. にLEVER をBUSH WASHER BOLT で取付",
"◆2. BUSH にｸﾞﾘｰｽを塗布する",
"5. BOLT にWASHER SPRING WASHER の順番で通す",
"◆4. BOLT にｸﾞﾘｰｽを塗布",
"6. にBOLT を入れる"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付ﾄﾙｸ 3.2N･m",
"◆作業者安全作業",
"締付ﾄﾙｸ 3.2N･m",
"･切削面にｸﾞﾘｰｽ塗布 米粒:2"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "320cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟ部の組立(1/3)",
"WorkItems": [
"1. LEVER LEVER BRACKET SHAFT の指示部を面取りする"
],
"WorkPoints": [
"面取りの箇所は取付け部か摺動部の為充分に拭きあげておくこと｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"表裏部",
"左右上面",
"端面"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟ部の組立(2/3)",
"WorkItems": [
"1. SPACER にBEARING WASHER をBOLT WASHER で取付",
"2. SPACER にBEARING WASHER をBOLT WASHER で取付",
"◆3. にｸﾞﾘｰｽを塗布する",
"4. に を入れる",
"5. BEARING の組立品を の組立品へWASHER BOLT で取付"
],
"WorkPoints": [
"･指示部にｸﾞﾘｰｽ塗布",
"締付けはSD-A000962-013で締付け",
"締付けはSD-A000962-013で締付け",
"締付けはSD-A000962-013で締付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WASHER BOLT ",
"WASHER BOLT ",
"SPACER ",
"BEARING ",
"BOLT ",
"WASHER ",
"WASHER ",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1(2ヵ所)"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟ部の組立(2/3)",
"WorkItems": [
"1. SPACER にBEARING WASHER をBOLT WASHER で取付",
"2. SPACER にBEARING WASHER をBOLT WASHER で取付",
"◆3. にｸﾞﾘｰｽを塗布する",
"4. に を入れる",
"5. BEARING の組立品を の組立品へWASHER BOLT で取付"
],
"WorkPoints": [
"･指示部にｸﾞﾘｰｽ塗布",
"締付けはSD-A000962-013で締付け",
"締付けはSD-A000962-013で締付け",
"締付けはSD-A000962-013で締付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WASHER BOLT ",
"WASHER BOLT ",
"SPACER ",
"BEARING ",
"BOLT ",
"WASHER ",
"WASHER ",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1(2ヵ所)"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒/1粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｸﾗﾝﾌﾟ部組立治具",
"Size": "",
"ToolOther": "FM-4062",
"WorkName": "ｸﾗﾝﾌﾟ部の組立(3/3)",
"WorkItems": [
"1. を治具に取付ける"
],
"WorkPoints": [
"浮きが無いこと確認しﾚｰﾊﾞｰを締めて固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4062",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｸﾗﾝﾌﾟ部の組立(3/3)",
"WorkItems": [
"2. Aを締付け",
"3. Bを締付け"
],
"WorkPoints": [
"締付けの際浮きが無いことを確認し締付ける",
"締付けの際浮きが無いことを確認し締付ける"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付ﾄﾙｸ 150cN･m"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ(A002)の面取り",
"WorkItems": [
"1. PLATE に油砥石をかける"
],
"WorkPoints": [
"指示部分にかける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"※砥石掛け部"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "圧入治具ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "PLATE部組立(1/4)S-PIN圧入とｶﾞｲﾄﾞの取付",
"WorkItems": [
"1. へPIN PIN を圧入する",
"2. にGUIDE GUIDE をBOLT WASHER で取付け"
],
"WorkPoints": [
"ﾋﾟﾝの出代に注意 (5㎜･11㎜)",
"この工程では仮取付け､本締めはSD-A000962-024にて締め付け",
"A側に押す",
"下側に押す"
],
"Tolks": [
"締付ﾄﾙｸ 320cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5㎜",
"11㎜",
"FM-2254",
"GUIDE ",
"GUIDE "
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5㎜出代:11㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PLATE部組立(1/4)S-PIN圧入とｶﾞｲﾄﾞの取付",
"WorkItems": [
"1. へPIN PIN を圧入する",
"2. にGUIDE GUIDE をBOLT WASHER で取付け"
],
"WorkPoints": [
"ﾋﾟﾝの出代に注意 (5㎜･11㎜)",
"この工程では仮取付け､本締めはSD-A000962-024にて締め付け",
"A側に押す",
"下側に押す"
],
"Tolks": [
"締付ﾄﾙｸ 320cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5㎜",
"11㎜",
"FM-2254",
"GUIDE ",
"GUIDE "
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "320cN･m",
"WorkName": "PLATE部組立(1/4)S-PIN圧入とｶﾞｲﾄﾞの取付",
"WorkItems": [
"1. へPIN PIN を圧入する",
"2. にGUIDE GUIDE をBOLT WASHER で取付け"
],
"WorkPoints": [
"ﾋﾟﾝの出代に注意 (5㎜･11㎜)",
"この工程では仮取付け､本締めはSD-A000962-024にて締め付け",
"下側に押す"
],
"Tolks": [
"締付ﾄﾙｸ 320cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"11㎜"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "320cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PLATE部組立(2/4)",
"WorkItems": [
"◆1. SPRING ･SPACER にｸﾞﾘｰｽを塗布",
"2. BOLT にSPRING WASHER SPACER を通す",
"3. に2,をWASHER NUT で取付",
"1. にCLIP をBOLT で取付け"
],
"WorkPoints": [
"BOLT を押した後に､ｽﾑｰｽﾞに戻ること",
"CLIP の取付け方向は下図参照",
"･SPRING ･SPACER の外周 にｸﾞﾘｰｽを塗布する"
],
"Tolks": [
"締付けﾄﾙｸ: 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付けﾄﾙｸ: 95cN･m",
"WASHER NUT ",
"BOLT SPACER SPRING WASHER ",
"SPRING ",
"SPACER ",
"WASHER ",
"BOLT ",
"CLIP BOLT ",
"ｸﾞﾘｰｽ塗布 米粒:2"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒/2粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "PLATE部組立(2/4)",
"WorkItems": [
"◆1. SPRING ･SPACER にｸﾞﾘｰｽを塗布",
"2. BOLT にSPRING WASHER SPACER を通す",
"3. に2,をWASHER NUT で取付",
"1. にCLIP をBOLT で取付け"
],
"WorkPoints": [
"BOLT を押した後に､ｽﾑｰｽﾞに戻ること",
"CLIP の取付け方向は下図参照",
"･SPRING ･SPACER の外周 にｸﾞﾘｰｽを塗布する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PLATE部組立(3/4)",
"WorkItems": [
"2. SENSOR へLABEL を取付け"
],
"WorkPoints": [
"被服ﾁｭｰﾌﾞ端面とﾗﾍﾞﾙの端面を合わせること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PLATE部組立(4/4)",
"WorkItems": [
"1. に をBOLT WASHER WASHER で取付け"
],
"WorkPoints": [
"取付位置･方向注意を下図参照にして取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"BOLT WASHER WASHER ",
"ｾﾝｻｰの矢印方向注意",
"刻印有り",
"ﾌﾛﾝﾄ用B06R",
"ﾌﾛﾝﾄ用B05R",
"ﾌﾛﾝﾄ用B04R",
"ﾌﾛﾝﾄ用B03R",
"ﾘｱ用B16R",
"ﾘｱ用B15R",
"ﾘｱ用B14R",
"ﾘｱ用B13R",
"当付方向",
"※ｾﾝｻｰの刻印側を図の方向とする｡※ｾﾝｻｰの当付を図の方向とする｡(これにより､斜光ﾎﾞﾙﾄの中央がｾﾝｻｰの中央位置となる｡)※必ず､ﾄﾙｸﾄﾞﾗｲﾊﾞｰでﾎﾞﾙﾄを固定する事(ｾﾝｻｰが破損しやすい)※ﾏｰｷﾝｸﾞﾀｲを図の番号通り取付",
"刻 印 側",
"締付けﾄﾙｸ: 40cN･m",
"BOLT ",
"WASHER ",
"WASHER ",
"当付方向"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "40cN･m",
"WorkName": "PLATE部組立(4/4)",
"WorkItems": [
"1. に をBOLT WASHER WASHER で取付け"
],
"WorkPoints": [
"取付位置･方向注意を下図参照にして取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"BOLT WASHER WASHER ",
"ｾﾝｻｰの矢印方向注意",
"刻印有り",
"ﾌﾛﾝﾄ用B06R",
"ﾌﾛﾝﾄ用B05R",
"ﾌﾛﾝﾄ用B04R",
"ﾌﾛﾝﾄ用B03R",
"ﾘｱ用B16R",
"ﾘｱ用B15R",
"ﾘｱ用B14R",
"ﾘｱ用B13R",
"当付方向",
"※ｾﾝｻｰの刻印側を図の方向とする｡※ｾﾝｻｰの当付を図の方向とする｡(これにより､斜光ﾎﾞﾙﾄの中央がｾﾝｻｰの中央位置となる｡)※必ず､ﾄﾙｸﾄﾞﾗｲﾊﾞｰでﾎﾞﾙﾄを固定する事(ｾﾝｻｰが破損しやすい)※ﾏｰｷﾝｸﾞﾀｲを図の番号通り取付",
"刻 印 側",
"締付けﾄﾙｸ: 40cN･m",
"BOLT ",
"WASHER ",
"WASHER ",
"当付方向"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞｯｷﾝｸﾞ(1/3)",
"WorkItems": [
"1. に をBOLT WASHER で取付",
"2. に をBOLT WASHER で取付",
"2. の裏へCLIP をBOLT で取付"
],
"WorkPoints": [
"調整後に指定ﾄﾙｸで仮締め締付けはSD-A000962-024にて締め付け",
"調整後に指定ﾄﾙｸで仮締め締付けはSD-A000962-023にて締め付け"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"BOLT WASHER "
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "ﾄﾞｯｷﾝｸﾞ(1/3)",
"WorkItems": [
"1. に をBOLT WASHER で取付",
"2. の裏へCLIP をBOLT で取付"
],
"WorkPoints": [
"調整後に指定ﾄﾙｸで仮締め締付けはSD-A000962-024にて締め付け"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線・JOINT取付",
"WorkItems": [
"1. .配線を固定する",
"2. にJOINT SILENCER を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"SILENCER ",
"JOINT "
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾄﾞｯｷﾝｸﾞ(2/3)",
"WorkItems": [
"1. に をBOLT WASHER で取付"
],
"WorkPoints": [
"段差部と平行に取付ける為にﾌﾞﾛｯｸｹﾞｰｼﾞをはさむ事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付けﾄﾙｸ:3.2N･m",
"3㎜ﾌﾞﾛｯｸｹﾞｰｼﾞ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "3㎜",
"ToolOther": "",
"WorkName": "ﾄﾞｯｷﾝｸﾞ(2/3)",
"WorkItems": [
"1. に をBOLT WASHER で取付"
],
"WorkPoints": [
"段差部と平行に取付ける為にﾌﾞﾛｯｸｹﾞｰｼﾞをはさむ事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付けﾄﾙｸ:3.2N･m",
"3㎜ﾌﾞﾛｯｸｹﾞｰｼﾞ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "3.0㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "50cN･m",
"WorkName": "ﾄﾞｯｷﾝｸﾞ(2/3)",
"WorkItems": [
"2. に をBOLT WASHER で取付け"
],
"WorkPoints": [
" を取付ける際ｴｱｰﾁｭｰﾌﾞを の穴に通しておくこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付けﾄﾙｸ:50cN･m"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞｵﾌﾟｼｮﾝ駆動ﾕﾆｯﾄ組立治具",
"Size": "",
"ToolOther": "FM-2124",
"WorkName": "ﾄﾞｯｷﾝｸﾞ(3/3)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2124",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞｯｷﾝｸﾞ(3/3)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "200cN・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞｯｷﾝｸﾞ(3/3)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "方向確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りの方向で取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞｯｷﾝｸﾞ(3/3)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒/1粒小豆/1粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "調整1",
"WorkItems": [
"1. 駆動部に治具を置く",
"2. ﾍﾞｱﾘﾝｸﾞの当りを調整",
"3. 各調整部のﾎﾞﾙﾄを締結"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞの当たり :片当り､隙間無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付けﾄﾙｸ: 150cN･m",
"締付けﾄﾙｸ: 320cN･m",
"検査表 :ｸﾗﾝﾊﾟすきま確認",
"締付けﾄﾙｸ: 150cN･m",
"締付けﾄﾙｸ: 320cN･m"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｸﾗﾝﾊﾟ組立治具",
"Size": "",
"ToolOther": "FM-2231",
"WorkName": "調整1",
"WorkItems": [
"1. 駆動部に治具を置く",
"2. ﾍﾞｱﾘﾝｸﾞの当りを調整",
"1. 駆動部に治具を置く",
"2. ﾍﾞｱﾘﾝｸﾞの当りを調整",
"3. 各調整部のﾎﾞﾙﾄを締結"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞの当たり :片当り､隙間無い事",
"ﾍﾞｱﾘﾝｸﾞの当たり :片当り､隙間無い事"
],
"Tolks": [],
"InspectionNo": "WDQB-F013-006",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付けﾄﾙｸ: 150cN･m",
"締付けﾄﾙｸ: 320cN･m",
"検査表 :ｸﾗﾝﾊﾟすきま確認",
"締付けﾄﾙｸ: 150cN･m",
"締付けﾄﾙｸ: 320cN･m",
"検査表 :ｸﾗﾝﾊﾟすきま確認",
"締付けﾄﾙｸ: 150cN･m",
"締付けﾄﾙｸ: 320cN･m",
"WDQB-F013-006"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-2231",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間無き事片当たり無き事",
"Method": "目視",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰﾛｯｸ部確認治具",
"Size": "",
"ToolOther": "FM-2904",
"WorkName": "調整1",
"WorkItems": [
"4. ﾎﾙﾀﾞ治具の取付を確認する"
],
"WorkPoints": [
"ﾎﾙﾀﾞ脱着時 引っかかり無い事",
"ﾎﾙﾀﾞ装着時 XYZ 方向にｶﾞﾀ無い事"
],
"Tolks": [],
"InspectionNo": "WDQB-F013-006",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾎﾙﾀﾞ取付確認",
"WDQB-F013-006"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-2904",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間無き事片当たり無き事",
"Method": "目視",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰﾛｯｸ部確認治具",
"Size": "",
"ToolOther": "FM-2123",
"WorkName": "調整1",
"WorkItems": [
"4. ﾎﾙﾀﾞ治具の取付を確認する"
],
"WorkPoints": [
"ﾎﾙﾀﾞ脱着時 引っかかり無い事",
"ﾎﾙﾀﾞ装着時 XYZ 方向にｶﾞﾀ無い事"
],
"Tolks": [],
"InspectionNo": "WDQB-F013-006",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾎﾙﾀﾞ取付確認",
"WDQB-F013-006"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2123",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "引っ掛かり無き事",
"Method": "手感",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰﾛｯｸ部確認治具",
"Size": "",
"ToolOther": "FM-2123",
"WorkName": "調整1",
"WorkItems": [
"4. ﾎﾙﾀﾞ治具の取付を確認する"
],
"WorkPoints": [
"ﾎﾙﾀﾞ脱着時 引っかかり無い事",
"ﾎﾙﾀﾞ装着時 XYZ 方向にｶﾞﾀ無い事"
],
"Tolks": [],
"InspectionNo": "WDQB-F013-006",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾎﾙﾀﾞ取付確認",
"WDQB-F013-006"
]
} | {
"QualityItem": "ｶﾞﾀ確認",
"ToolManageNo": "FM-2123",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｶﾞﾀ無き事",
"Method": "手感",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼﾘﾝﾀﾞｰﾌﾞﾛｯｸ保持治具",
"Size": "",
"ToolOther": "FM-2124",
"WorkName": "調整2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"調整ﾎﾞﾙﾄ",
"3mmﾌﾞﾛｯｸｹﾞｰｼﾞ(ﾌﾟﾚｰﾄ)を挟み平行に調整"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2124",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞｵﾌﾟｼｮﾝ駆動ﾕﾆｯﾄ組立治具",
"Size": "",
"ToolOther": "FM-3087",
"WorkName": "調整2",
"WorkItems": [
"2. ｼﾘﾝﾀﾞ部の調整をする",
"1. 治具を置きP601/P602の位置きめを行う"
],
"WorkPoints": [
"㉖とシリンダ部間に㉙が通らないこと",
"㉘を挟み、シリンダ部を平行に調整する",
"㉖と 間に ㉙ が通らないこと"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.02mmのｼｯｸﾈｽｹﾞｰｼﾞが通らないこと",
"締付けﾄﾙｸ: 3.2N･m",
"検査表 :ｼﾘﾝﾀﾞｰ調整 ｼﾘﾝﾀﾞｰ位置調整",
"㉖を装着の前後で㉗の拭き差し負荷が変わらないこと",
"調整ﾎﾞﾙﾄ",
"3mmﾌﾞﾛｯｸｹﾞｰｼﾞ(ﾌﾟﾚｰﾄ)を挟み平行に調整",
"WDQB-F013-006"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-3087",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.02㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "0.02㎜",
"WorkName": "調整2",
"WorkItems": [
"2. ｼﾘﾝﾀﾞ部の調整をする",
"1. 治具を置きP601/P602の位置きめを行う"
],
"WorkPoints": [
"㉖とシリンダ部間に㉙が通らないこと",
"㉘を挟み、シリンダ部を平行に調整する",
"㉖と 間に ㉙ が通らないこと"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.02mmのｼｯｸﾈｽｹﾞｰｼﾞが通らないこと",
"締付けﾄﾙｸ: 3.2N･m",
"検査表 :ｼﾘﾝﾀﾞｰ調整 ｼﾘﾝﾀﾞｰ位置調整",
"㉖を装着の前後で㉗の拭き差し負荷が変わらないこと",
"調整ﾎﾞﾙﾄ",
"3mmﾌﾞﾛｯｸｹﾞｰｼﾞ(ﾌﾟﾚｰﾄ)を挟み平行に調整",
"WDQB-F013-006"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.02㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "3㎜",
"ToolOther": "",
"WorkName": "調整2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"調整ﾎﾞﾙﾄ",
"3mmﾌﾞﾛｯｸｹﾞｰｼﾞ(ﾌﾟﾚｰﾄ)を挟み平行に調整"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "3㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "調整2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"調整ﾎﾞﾙﾄ",
"3mmﾌﾞﾛｯｸｹﾞｰｼﾞ(ﾌﾟﾚｰﾄ)を挟み平行に調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾌﾞﾗｹｯﾄ取付と配管接続",
"WorkItems": [
"2. へ③を配管の接続を行う",
"1. に③をBOLT WASHER で取付け",
"3. 配管と一緒に固定"
],
"WorkPoints": [
"傾きが無いように下へ押し下げた状態で取付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付けﾄﾙｸ: 95cN･m",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾗｹｯﾄ取付と配管接続",
"WorkItems": [
"2. へ③を配管の接続を行う",
"1. に③をBOLT WASHER で取付け",
"3. 配管と一緒に固定"
],
"WorkPoints": [
"傾きが無いように下へ押し下げた状態で取付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付けﾄﾙｸ: 95cN･m",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りに接続されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"Size": "",
"ToolOther": "FM-2169",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ開閉機能検査",
"WorkItems": [
"･機能検査装置(ﾁｪｯｶｰ)と駆動部のｴｱｰ配管と電源を接続して､以下の動作を確認する｡･SW:開限側→ﾗﾝﾌﾟ開限ON→ｼﾘﾝﾀﾞｰ前進･SW:閉限側→ﾗﾝﾌﾟ閉限ON→ｼﾘﾝﾀﾞｰ後進"
],
"WorkPoints": [
"･ﾚｷﾞｭﾚｰﾀの設定が0.5Mpaである事｡･配線と配管を接続してからｴｱｰの絞りを開き､ 電源のSWをONにする事｡･確実に目視で確認する事｡･ﾗﾝﾌﾟの点灯が逆の場合は､駆動部のｺﾈｸﾀ 接続ﾐｽの可能性が高い｡･重点教育要｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"\"閉限\"ON",
"SW\"閉限\"",
"ｼﾘﾝﾀﾞｰ動作",
"ｼﾘﾝﾀﾞｰ動作",
"\"開限\"ON",
"SW\"開限\"",
"検査表 :ﾎﾙﾀﾞ取付確認",
"検査表 :ﾎﾙﾀﾞ種別ｾﾝｻの検出確認を行う｡",
"WDQB-F013-006"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2169",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに動作する事",
"Method": "目視",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"Size": "",
"ToolOther": "FM-2169",
"WorkName": "2ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査",
"WorkItems": [
"1. ﾁｪﾝｼﾞｬｰの自重落下確認 2ﾉｽﾞﾙﾁｪﾝｼﾞｬｰを駆動部にｾｯﾄする(図:ﾁｪﾝｼﾞｬｰ自重落下確認参照)",
"2. ②ﾉｽﾞﾙ治具ｾｯﾄ開閉確認･2ﾉｽﾞﾙﾁｪﾝｼﾞｬｰを駆動部ﾕﾆｯﾄにｾｯﾄした状態で､装置のSWを \"開\"側にし､2ﾉｽﾞﾙ治具をｾｯﾄする｡･装置でSWを\"閉\"側にし､開閉異常がないか確認する｡",
"3. ﾁｪﾝｼﾞｬｰの自重落下確認",
"4. 2ﾉｽﾞﾙ治具ｾｯﾄ開閉確認"
],
"WorkPoints": [
"･自重落下させる時は､ひっかかりなくｽﾑｰｽﾞである事｡･2ﾁｪﾝｼﾞｬｰとｽﾀﾝﾄﾞに隙間が無い事(目視確認)｡･装置の2ﾉｽﾞﾙﾗﾝﾌﾟが点灯する事｡･重点教育要｡",
"2ﾉｽﾞﾙﾁｪﾝｼﾞｬｰのｼｬｯﾀｰ開閉がひっかかりなく､ｽﾑｰｽﾞである事｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚﾊﾞｰを押す",
"自重落下",
"目視:隙間無い事",
"2ﾉｽﾞﾙﾗﾝﾌﾟ点灯する事",
"SW\"開\"側",
"ｼｬｯﾀｰ\"開\"",
"SW\"閉\"側",
"ｼｬｯﾀｰ\"閉\"",
"2ﾉｽﾞﾙ治具をｾｯﾄ",
"検査表 :ﾎﾙﾀﾞ取付確認",
"検査表 :ﾎﾙﾀﾞ種別ｾﾝｻの検出確認を行う｡",
"WDQB-F013-006"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2169",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに動作する事",
"Method": "目視",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "2ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査",
"WorkItems": [
"1. ﾁｪﾝｼﾞｬｰの自重落下確認 2ﾉｽﾞﾙﾁｪﾝｼﾞｬｰを駆動部にｾｯﾄする(図:ﾁｪﾝｼﾞｬｰ自重落下確認参照)",
"2. ②ﾉｽﾞﾙ治具ｾｯﾄ開閉確認･2ﾉｽﾞﾙﾁｪﾝｼﾞｬｰを駆動部ﾕﾆｯﾄにｾｯﾄした状態で､装置のSWを \"開\"側にし､2ﾉｽﾞﾙ治具をｾｯﾄする｡･装置でSWを\"閉\"側にし､開閉異常がないか確認する｡",
"3. ﾁｪﾝｼﾞｬｰの自重落下確認",
"4. 2ﾉｽﾞﾙ治具ｾｯﾄ開閉確認"
],
"WorkPoints": [
"･自重落下させる時は､ひっかかりなくｽﾑｰｽﾞである事｡･2ﾁｪﾝｼﾞｬｰとｽﾀﾝﾄﾞに隙間が無い事(目視確認)｡･装置の2ﾉｽﾞﾙﾗﾝﾌﾟが点灯する事｡･重点教育要｡",
"2ﾉｽﾞﾙﾁｪﾝｼﾞｬｰのｼｬｯﾀｰ開閉がひっかかりなく､ｽﾑｰｽﾞである事｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚﾊﾞｰを押す",
"自重落下",
"目視:隙間無い事",
"2ﾉｽﾞﾙﾗﾝﾌﾟ点灯する事",
"SW\"開\"側",
"ｼｬｯﾀｰ\"開\"",
"SW\"閉\"側",
"ｼｬｯﾀｰ\"閉\"",
"2ﾉｽﾞﾙ治具をｾｯﾄ",
"検査表 :ﾎﾙﾀﾞ取付確認",
"検査表 :ﾎﾙﾀﾞ種別ｾﾝｻの検出確認を行う｡",
"WDQB-F013-006"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｽﾑｰｽﾞに動作する事",
"Method": "目視",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"Size": "",
"ToolOther": "FM-2169",
"WorkName": "8ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査",
"WorkItems": [
"1. ﾁｪﾝｼﾞｬｰの自重落下確認 8ﾉｽﾞﾙﾁｪﾝｼﾞｬｰを駆動部にｾｯﾄする(図:ﾁｪﾝｼﾞｬｰ自重落下確認参照)",
"1. ②ﾉｽﾞﾙ治具ｾｯﾄ開閉確認･8ﾉｽﾞﾙﾁｪﾝｼﾞｬｰを駆動部ﾕﾆｯﾄにｾｯﾄした状態で､装置のSWを \"開\"側にし､8ﾉｽﾞﾙ治具をｾｯﾄする｡･装置でSWを\"閉\"側にし､開閉異常がないか確認する｡",
"2. ﾁｪﾝｼﾞｬｰの自重落下確認",
"3. 8ﾉｽﾞﾙ治具ｾｯﾄ開閉確認"
],
"WorkPoints": [
"･自重落下させる時は､ひっかかりなくｽﾑｰｽﾞである事｡･8ﾁｪﾝｼﾞｬｰとｽﾀﾝﾄﾞに隙間が無い事(目視確認)｡･装置の8ﾉｽﾞﾙﾗﾝﾌﾟが点灯する事｡･重点教育要｡",
"8ﾉｽﾞﾙﾁｪﾝｼﾞｬｰのｼｬｯﾀｰ開閉がひっかかりなく､ｽﾑｰｽﾞである事｡"
],
"Tolks": [],
"InspectionNo": "WDQB-F013-006",
"InspectionItems": [
"検査表 :ﾎﾙﾀﾞ取付確認"
],
"WorkTypes": [],
"Words": [
"ﾚﾊﾞｰを押す",
"自重落下",
"目視:隙間無い事",
"8ﾉｽﾞﾙﾗﾝﾌﾟ点灯する事",
"ｼｬｯﾀｰ\"開\"",
"SW\"閉\"側",
"ｼｬｯﾀｰ\"閉\"",
"2ﾉｽﾞﾙ治具をｾｯﾄ",
"SW\"開\"側",
"検査表 :ﾎﾙﾀﾞ種別ｾﾝｻの検出確認を行う｡",
"WDQB-F013-006"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2169",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに動作する事",
"Method": "目視",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬﾛｯｸ部確認治具",
"Size": "",
"ToolOther": "FM-2123",
"WorkName": "8ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査",
"WorkItems": [
"1. ﾁｪﾝｼﾞｬｰの自重落下確認 8ﾉｽﾞﾙﾁｪﾝｼﾞｬｰを駆動部にｾｯﾄする(図:ﾁｪﾝｼﾞｬｰ自重落下確認参照)",
"1. ②ﾉｽﾞﾙ治具ｾｯﾄ開閉確認･8ﾉｽﾞﾙﾁｪﾝｼﾞｬｰを駆動部ﾕﾆｯﾄにｾｯﾄした状態で､装置のSWを \"開\"側にし､8ﾉｽﾞﾙ治具をｾｯﾄする｡･装置でSWを\"閉\"側にし､開閉異常がないか確認する｡",
"2. ﾁｪﾝｼﾞｬｰの自重落下確認",
"3. 8ﾉｽﾞﾙ治具ｾｯﾄ開閉確認"
],
"WorkPoints": [
"･自重落下させる時は､ひっかかりなくｽﾑｰｽﾞである事｡･8ﾁｪﾝｼﾞｬｰとｽﾀﾝﾄﾞに隙間が無い事(目視確認)｡･装置の8ﾉｽﾞﾙﾗﾝﾌﾟが点灯する事｡･重点教育要｡",
"8ﾉｽﾞﾙﾁｪﾝｼﾞｬｰのｼｬｯﾀｰ開閉がひっかかりなく､ｽﾑｰｽﾞである事｡"
],
"Tolks": [],
"InspectionNo": "WDQB-F013-006",
"InspectionItems": [
"検査表 :ﾎﾙﾀﾞ取付確認"
],
"WorkTypes": [],
"Words": [
"ﾚﾊﾞｰを押す",
"自重落下",
"目視:隙間無い事",
"8ﾉｽﾞﾙﾗﾝﾌﾟ点灯する事",
"ｼｬｯﾀｰ\"開\"",
"SW\"閉\"側",
"ｼｬｯﾀｰ\"閉\"",
"2ﾉｽﾞﾙ治具をｾｯﾄ",
"SW\"開\"側",
"検査表 :ﾎﾙﾀﾞ種別ｾﾝｻの検出確認を行う｡",
"WDQB-F013-006"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2123",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｽﾑｰｽﾞに動作する事",
"Method": "目視",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"Size": "",
"ToolOther": "FM-2169",
"WorkName": "12ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査",
"WorkItems": [
"1. ﾁｪﾝｼﾞｬｰの自重落下確認 12ﾉｽﾞﾙﾁｪﾝｼﾞｬｰを駆動部にｾｯﾄする(図:ﾁｪﾝｼﾞｬｰ自重落下確認参照)",
"2. ②ﾉｽﾞﾙ治具ｾｯﾄ開閉確認･12ﾉｽﾞﾙﾁｪﾝｼﾞｬｰを駆動部ﾕﾆｯﾄにｾｯﾄした状態で､装置のSWを \"開\"側にし､12ﾉｽﾞﾙ治具をｾｯﾄする｡･装置でSWを\"閉\"側にし､開閉異常がないか確認する｡",
"3. ﾁｪﾝｼﾞｬｰの自重落下確認",
"4. 12ﾉｽﾞﾙ治具ｾｯﾄ開閉確認"
],
"WorkPoints": [
"･自重落下させる時は､ひっかかりなくｽﾑｰｽﾞである事｡･12ﾁｪﾝｼﾞｬｰとｽﾀﾝﾄﾞに隙間が無い事(目視確認)｡･装置の12ﾉｽﾞﾙﾗﾝﾌﾟが点灯する事｡･重点教育要｡",
"12ﾉｽﾞﾙﾁｪﾝｼﾞｬｰのｼｬｯﾀｰ開閉がひっかかりなく､ｽﾑｰｽﾞである事｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾎﾙﾀﾞ取付確認",
"検査表 :ﾎﾙﾀﾞ種別ｾﾝｻの検出確認を行う｡",
"ﾚﾊﾞｰを押す",
"自重落下",
"目視:隙間無い事",
"12ﾉｽﾞﾙﾗﾝﾌﾟ点灯する事",
"ｼｬｯﾀｰ\"開\"",
"SW\"閉\"側",
"ｼｬｯﾀｰ\"閉\"",
"12ﾉｽﾞﾙ治具をｾｯﾄ",
"SW\"開\"側",
"WDQB-F013-006"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2169",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに動作する事",
"Method": "目視",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬﾛｯｸ部確認治具",
"Size": "",
"ToolOther": "FM-2123",
"WorkName": "12ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査",
"WorkItems": [
"4. 12ﾉｽﾞﾙ治具ｾｯﾄ開閉確認"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚﾊﾞｰを押す",
"自重落下",
"目視:隙間無い事",
"12ﾉｽﾞﾙﾗﾝﾌﾟ点灯する事",
"ｼｬｯﾀｰ\"開\"",
"SW\"閉\"側",
"ｼｬｯﾀｰ\"閉\"",
"12ﾉｽﾞﾙ治具をｾｯﾄ",
"SW\"開\"側",
"WDQB-F013-006"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2123",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｽﾑｰｽﾞに動作する事",
"Method": "目視",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"Size": "",
"ToolOther": "FM-2169",
"WorkName": "3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査",
"WorkItems": [
"1. ﾁｪﾝｼﾞｬｰの自重落下確認 3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰを駆動部にｾｯﾄする(図:ﾁｪﾝｼﾞｬｰ自重落下確認参照)",
"2. ②ﾉｽﾞﾙ治具ｾｯﾄ開閉確認･3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰを駆動部ﾕﾆｯﾄにｾｯﾄした状態で､装置のSWを \"開\"側にし､3(2)ﾉｽﾞﾙ治具をｾｯﾄする｡･装置でSWを\"閉\"側にし､開閉異常がないか確認する｡",
"3. ﾁｪﾝｼﾞｬｰの自重落下確認"
],
"WorkPoints": [
"･自重落下させる時は､ひっかかりなくｽﾑｰｽﾞである事｡･3ﾁｪﾝｼﾞｬｰとｽﾀﾝﾄﾞに隙間が無い事(目視確認)｡･装置の3ﾉｽﾞﾙﾗﾝﾌﾟが消灯する事｡･重点教育要｡",
"3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰのｼｬｯﾀｰ開閉がひっかかりなく､ｽﾑｰｽﾞである事｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ使用",
"検査表 :ﾎﾙﾀﾞ取付確認",
"検査表 :ﾎﾙﾀﾞ種別ｾﾝｻの検出確認を行う｡",
"WDQB-F013-006"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2169",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに動作する事",
"Method": "目視",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査",
"WorkItems": [
"1. ﾁｪﾝｼﾞｬｰの自重落下確認 3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰを駆動部にｾｯﾄする(図:ﾁｪﾝｼﾞｬｰ自重落下確認参照)",
"2. ②ﾉｽﾞﾙ治具ｾｯﾄ開閉確認･3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰを駆動部ﾕﾆｯﾄにｾｯﾄした状態で､装置のSWを \"開\"側にし､3(2)ﾉｽﾞﾙ治具をｾｯﾄする｡･装置でSWを\"閉\"側にし､開閉異常がないか確認する｡",
"3. ﾁｪﾝｼﾞｬｰの自重落下確認",
"4. 3(2)ﾉｽﾞﾙ治具ｾｯﾄ開閉確認"
],
"WorkPoints": [
"･自重落下させる時は､ひっかかりなくｽﾑｰｽﾞである事｡･3ﾁｪﾝｼﾞｬｰとｽﾀﾝﾄﾞに隙間が無い事(目視確認)｡･装置の3ﾉｽﾞﾙﾗﾝﾌﾟが消灯する事｡･重点教育要｡",
"3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰのｼｬｯﾀｰ開閉がひっかかりなく､ｽﾑｰｽﾞである事｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ使用",
"3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ使用",
"3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ使用",
"3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ使用",
"ﾚﾊﾞｰを押す",
"自重落下",
"目視:隙間無い事",
"ｼｬｯﾀｰ\"開\"",
"SW\"閉\"側",
"ｼｬｯﾀｰ\"閉\"",
"3(2)ﾉｽﾞﾙ治具をｾｯﾄ",
"SW\"開\"側",
"赤ﾗﾝﾌﾟが消灯する事",
"検査表 :ﾎﾙﾀﾞ取付確認",
"検査表 :ﾎﾙﾀﾞ種別ｾﾝｻの検出確認を行う｡",
"WDQB-F013-006"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｽﾑｰｽﾞに動作する事",
"Method": "目視",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-3418",
"WorkName": "3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査",
"WorkItems": [
"1. ﾁｪﾝｼﾞｬｰの自重落下確認 3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰを駆動部にｾｯﾄする(図:ﾁｪﾝｼﾞｬｰ自重落下確認参照)",
"2. ②ﾉｽﾞﾙ治具ｾｯﾄ開閉確認･3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰを駆動部ﾕﾆｯﾄにｾｯﾄした状態で､装置のSWを \"開\"側にし､3(2)ﾉｽﾞﾙ治具をｾｯﾄする｡･装置でSWを\"閉\"側にし､開閉異常がないか確認する｡",
"3. ﾁｪﾝｼﾞｬｰの自重落下確認"
],
"WorkPoints": [
"･自重落下させる時は､ひっかかりなくｽﾑｰｽﾞである事｡･3ﾁｪﾝｼﾞｬｰとｽﾀﾝﾄﾞに隙間が無い事(目視確認)｡･装置の3ﾉｽﾞﾙﾗﾝﾌﾟが消灯する事｡･重点教育要｡",
"3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰのｼｬｯﾀｰ開閉がひっかかりなく､ｽﾑｰｽﾞである事｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ使用",
"検査表 :ﾎﾙﾀﾞ取付確認",
"検査表 :ﾎﾙﾀﾞ種別ｾﾝｻの検出確認を行う｡",
"WDQB-F013-006"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-3418",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "赤ﾗﾝﾌﾟが消灯する事",
"Method": "PHﾁｪｯｶｰ",
"RecordMethod": "WDQB-F013-006",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け_2",
"WorkItems": [
"1. に②LABEL を貼付け"
],
"WorkPoints": [
" の貼付け部分の油分･ごみ等を除去する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"74mm",
"5mm",
"74mm",
"5mm",
"4mm"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに貼付けてある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾞﾘｰｽ塗布",
"WorkItems": [
"◆1. ｸﾞﾘｰｽｱｯﾌﾟを実施"
],
"WorkPoints": [
"2,8,12ﾁｪﾝｼﾞｬｰ接触面にｸﾞﾘｰｽ塗布(各ﾁｪﾝｼﾞｬｰとこすれが生じる箇所)",
"赤丸部:ｸﾞﾘｰｽ塗布部分",
"青丸部:ｸﾞﾘｰｽ塗布部分"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:1",
"10mm程度"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒/1粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷準備",
"WorkItems": [
"1. ﾁｪﾝｼﾞｬｰ駆動部ﾕﾆｯﾄ(本体1台当たり2ﾕﾆｯﾄ使用)"
],
"WorkPoints": [
"ﾌﾛﾝﾄ用:ｺﾈｸﾀB03R､B04R､B05R､B06R ﾘｱ用 :ｺﾈｸﾀB13R､B14R､B15R､B16R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"PLATE 検査書有無確認(N210142855)検査書が添付されている事｡"
]
} | {
"QualityItem": "準備確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに準備してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "1.2N･m",
"WorkName": "ﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"1. VALVE にJOINT SILENCER JOINT を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"2. 1完成品にTUBE を取付ける"
],
"WorkPoints": [
"TUBE を120㎜にｶｯﾄする",
"ｻｲﾚﾝｻの根元を掴んで取付けの事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "120㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｼﾘﾝﾀﾞ組立1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｼﾘﾝﾀﾞ組立2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 米粒:1",
"全体にｸﾞﾘｰｽ塗布 米粒:1",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "5.5㎜",
"ToolOther": "1.2N･m",
"WorkName": "ｼﾘﾝﾀﾞ組立2",
"WorkItems": [],
"WorkPoints": [
"FM-3087が入った状態で0.1㎜が通ら無い事(16±0.1㎜)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"付属ﾅｯﾄ",
"付属ﾅｯﾄ",
"0.1㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ｼﾘﾝﾀﾞ組立2",
"WorkItems": [],
"WorkPoints": [
"FM-3087が入った状態で0.1㎜が通ら無い事(16±0.1㎜)"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-C01",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"付属ﾅｯﾄ",
"付属ﾅｯﾄ",
"0.1㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"◆作業者安全作業",
"WEAV-G002-C01"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｽﾄﾛｰｸ:16±0.1㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C01",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼﾘﾝﾀﾞｰﾌﾞﾛｯｸ保持治具",
"Size": "",
"ToolOther": "FM-3087",
"WorkName": "ｼﾘﾝﾀﾞ組立2",
"WorkItems": [],
"WorkPoints": [
"FM-3087が入った状態で0.1㎜が通ら無い事(16±0.1㎜)"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-C01",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"付属ﾅｯﾄ",
"付属ﾅｯﾄ",
"0.1㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"◆作業者安全作業",
"WEAV-G002-C01"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "FM-3087",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｽﾄﾛｰｸ:16±0.1㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-C01",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾘﾝﾀﾞ組立2",
"WorkItems": [
"◆3. WASHER GUIDE WASHER SPRING にｸﾞﾘｰｽを塗布する",
"4. CYLINDER(300MM) にWASHER GUIDE WASHER SPRING 付属ﾅｯﾄを入れる",
"5. を取付ける",
"2. CYLINDER(300MM) にSPACER をBOLT で取付ける",
"1. CYLINDER(300MM) の付属ﾅｯﾄを 取り外す",
"6. ｼﾘﾝﾀﾞのｽﾄﾛｰｸを調整し付属ﾅｯﾄで固定する"
],
"WorkPoints": [
"組込む前に塗布する事",
"ｽﾌﾟﾘﾝｸﾞを飛ばさないように注意",
"FM-3087が入った状態で0.1㎜が通ら無い事(16±0.1㎜)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"付属ﾅｯﾄ",
"付属ﾅｯﾄ",
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 米粒:1",
"全体にｸﾞﾘｰｽ塗布 米粒:1",
"検査表WASHER :ｼﾘﾝﾀﾞｰ調整",
"0.1㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各2粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾘﾝﾀﾞ組立2",
"WorkItems": [
"◆3. WASHER GUIDE WASHER SPRING にｸﾞﾘｰｽを塗布する",
"4. CYLINDER(300MM) にWASHER GUIDE WASHER SPRING 付属ﾅｯﾄを入れる",
"5. を取付ける",
"2. CYLINDER(300MM) にSPACER をBOLT で取付ける",
"1. CYLINDER(300MM) の付属ﾅｯﾄを 取り外す",
"6. ｼﾘﾝﾀﾞのｽﾄﾛｰｸを調整し付属ﾅｯﾄで固定する"
],
"WorkPoints": [
"組込む前に塗布する事",
"ｽﾌﾟﾘﾝｸﾞを飛ばさないように注意",
"FM-3087が入った状態で0.1㎜が通ら無い事(16±0.1㎜)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"付属ﾅｯﾄ",
"付属ﾅｯﾄ",
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 米粒:1",
"全体にｸﾞﾘｰｽ塗布 米粒:1",
"検査表WASHER :ｼﾘﾝﾀﾞｰ調整",
"0.1㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "位置合わせ治具",
"Size": "",
"ToolOther": "FM-6131",
"WorkName": "ｼﾘﾝﾀﾞ組立3",
"WorkItems": [
"1. にPLATE BLOCK をBOLT WASHER で仮固定",
"2. 1完成品を㉜に装着し締結する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付けﾄﾙｸ: 95cN･m"
]
} | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-6131",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｼﾘﾝﾀﾞ組立3",
"WorkItems": [
"1. にPLATE BLOCK をBOLT WASHER で仮固定",
"2. 1完成品を㉜に装着し締結する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"締付けﾄﾙｸ: 95cN･m"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "位置合わせ治具",
"Size": "",
"ToolOther": "FM-6131",
"WorkName": "ｼﾘﾝﾀﾞ組立4",
"WorkItems": [
"1. に を取付ける",
"2. 出限(B02/12R)のｺﾈｸﾀｰに治具を繋ぎ ｼﾘﾝﾀﾞｰを伸ばしON領域にﾏｰｷﾝｸﾞする",
"3. 戻限(B01/11R)のｺﾈｸﾀｰに治具を繋ぎ ｼﾘﾝﾀﾞｰを縮めON領域にﾏｰｷﾝｸﾞする",
"4. 各ｾﾝｻｰを固定する"
],
"WorkPoints": [
"出限･戻り限の取付位置(下図参照)を間違わ無い事",
"右図を参照の事",
"右図を参照の事",
"NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"戻限(B01/11R)はﾏｰｷﾝｸﾞのｾﾝﾀｰで固定",
"出限(B02/12R)はﾏｰｷﾝｸﾞのｾﾝﾀｰで固定"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"(出限)",
"(戻限)",
"検査表 :ｼﾘﾝﾀﾞｰLS位置調整",
"検査表 :ｼﾘﾝﾀﾞｰLS位置調整",
"検査表 :ｼﾘﾝﾀﾞｰLS位置調整",
"取付方向確認側面にｼﾞｮｲﾝﾄ取付穴有",
"出限",
"戻限",
"ｾﾝﾀｰ",
"⇧ＬＳ調整位置",
"約3㎜",
"右側より近づけてONする位置",
"左側より近づけてONする位置",
"右側より近づけてONする位置",
"左側より近づけてONする位置",
"ＬＳ調整位置⇩",
"約3㎜",
"ｾﾝﾀｰ",
"ｺﾈｸﾀｰへ",
"ﾏｰｷﾝｸﾞをする",
"ｼﾘﾝﾀﾞｰ戻限用LS(B01/11R)",
"ｼﾘﾝﾀﾞｰ出限用LS(B02/12R)"
]
} | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-6131",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2375",
"WorkName": "ｼﾘﾝﾀﾞ組立4",
"WorkItems": [
"1. に を取付ける",
"2. 出限(B02/12R)のｺﾈｸﾀｰに治具を繋ぎ ｼﾘﾝﾀﾞｰを伸ばしON領域にﾏｰｷﾝｸﾞする",
"3. 戻限(B01/11R)のｺﾈｸﾀｰに治具を繋ぎ ｼﾘﾝﾀﾞｰを縮めON領域にﾏｰｷﾝｸﾞする",
"4. 各ｾﾝｻｰを固定する"
],
"WorkPoints": [
"出限･戻り限の取付位置(下図参照)を間違わ無い事",
"右図を参照の事",
"右図を参照の事",
"NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"戻限(B01/11R)はﾏｰｷﾝｸﾞのｾﾝﾀｰで固定",
"出限(B02/12R)はﾏｰｷﾝｸﾞのｾﾝﾀｰで固定"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "WEAV-G002-C01",
"InspectionItems": [
"検査表 :ｼﾘﾝﾀﾞｰLS位置調整",
"検査表 :ｼﾘﾝﾀﾞｰLS位置調整",
"検査表 :ｼﾘﾝﾀﾞｰLS位置調整"
],
"WorkTypes": [],
"Words": [
"(出限)",
"(戻限)",
"取付方向確認側面にｼﾞｮｲﾝﾄ取付穴有",
"出限",
"戻限",
"ｾﾝﾀｰ",
"⇧ＬＳ調整位置",
"約3㎜",
"右側より近づけてONする位置",
"左側より近づけてONする位置",
"右側より近づけてONする位置",
"左側より近づけてONする位置",
"ＬＳ調整位置⇩",
"約3㎜",
"ｾﾝﾀｰ",
"ｺﾈｸﾀｰへ",
"ﾏｰｷﾝｸﾞをする",
"ｼﾘﾝﾀﾞｰ戻限用LS(B01/11R)",
"ｼﾘﾝﾀﾞｰ出限用LS(B02/12R)",
"WEAV-G002-C01"
]
} | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-2375",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上下限位置でONする事",
"Method": "PHﾁｪｯｶｰ",
"RecordMethod": "WEAV-G002-C01",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾏｲﾅｽ1.6㎜",
"ToolOther": "10cN･m",
"WorkName": "ｼﾘﾝﾀﾞ組立4",
"WorkItems": [
"4. 各ｾﾝｻｰを固定する"
],
"WorkPoints": [
"右図を参照の事",
"戻限(B01/11R)はﾏｰｷﾝｸﾞのｾﾝﾀｰで固定",
"出限(B02/12R)はﾏｰｷﾝｸﾞのｾﾝﾀｰで固定"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"(戻限)",
"検査表 :ｼﾘﾝﾀﾞｰLS位置調整",
"検査表 :ｼﾘﾝﾀﾞｰLS位置調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄｽﾊﾟﾅ",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾘﾝﾀﾞ組立4",
"WorkItems": [
"1. に を取付ける",
"2. 出限(B02/12R)のｺﾈｸﾀｰに治具を繋ぎ ｼﾘﾝﾀﾞｰを伸ばしON領域にﾏｰｷﾝｸﾞする",
"3. 戻限(B01/11R)のｺﾈｸﾀｰに治具を繋ぎ ｼﾘﾝﾀﾞｰを縮めON領域にﾏｰｷﾝｸﾞする",
"4. 各ｾﾝｻｰを固定する"
],
"WorkPoints": [
"出限･戻り限の取付位置(下図参照)を間違わ無い事",
"右図を参照の事",
"右図を参照の事",
"NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"戻限(B01/11R)はﾏｰｷﾝｸﾞのｾﾝﾀｰで固定",
"出限(B02/12R)はﾏｰｷﾝｸﾞのｾﾝﾀｰで固定"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"(出限)",
"(戻限)",
"検査表 :ｼﾘﾝﾀﾞｰLS位置調整",
"検査表 :ｼﾘﾝﾀﾞｰLS位置調整",
"検査表 :ｼﾘﾝﾀﾞｰLS位置調整",
"取付方向確認側面にｼﾞｮｲﾝﾄ取付穴有",
"出限",
"戻限",
"ｾﾝﾀｰ",
"⇧ＬＳ調整位置",
"約3㎜",
"右側より近づけてONする位置",
"左側より近づけてONする位置",
"右側より近づけてONする位置",
"左側より近づけてONする位置",
"ＬＳ調整位置⇩",
"約3㎜",
"ｾﾝﾀｰ",
"ｺﾈｸﾀｰへ",
"ﾏｰｷﾝｸﾞをする",
"ｼﾘﾝﾀﾞｰ戻限用LS(B01/11R)",
"ｼﾘﾝﾀﾞｰ出限用LS(B02/12R)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2N･m±10%",
"Method": "ﾄﾙｸﾄｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾋﾟﾝ圧入1",
"WorkItems": [],
"WorkPoints": [
"3.5㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.5±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾗｹｯﾄﾋﾟﾝ圧入治具",
"Size": "",
"ToolOther": "FM-4532",
"WorkName": "ﾋﾟﾝ圧入1",
"WorkItems": [],
"WorkPoints": [
"3.5㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "出代確認",
"ToolManageNo": "FM-4532",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.5±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "200cN･m",
"WorkName": "ﾋﾟﾝ圧入1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 200cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "200cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "320cN･m",
"WorkName": "ﾚﾊﾞｰ組立1",
"WorkItems": [
"3. にWASHER を入れ､PLATE に③BOLT で取付ける",
"4. 3完成品にBOLT を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 320cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "320cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾚﾊﾞｰ組立1",
"WorkItems": [
"3. にWASHER を入れ､PLATE に③BOLT で取付ける",
"4. 3完成品にBOLT を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 320cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚﾊﾞｰ組立1",
"WorkItems": [
"1. PLATE に砥石をかけ防錆油を塗布する",
"3. にWASHER を入れ､PLATE に③BOLT で取付ける",
"4. 3完成品にBOLT を取付ける",
"◆2. WASHER にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"両面に砥石",
"外周にｸﾞﾘｰｽを塗布"
],
"Tolks": [
"締付ﾄﾙｸ 320cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "320cN･m",
"WorkName": "ﾚﾊﾞｰ組立2",
"WorkItems": [
"◆4. BOLT にｸﾞﾘｰｽを塗布する",
"5. BOLT にWASHER SPRING WASHER を通し､3完成品に取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 320cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "320cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.