input
stringclasses 1
value | instruction
stringlengths 222
1.92k
| output
stringlengths 193
312
| category
stringclasses 1
value | index
stringclasses 1
value | fileName
null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LCRﾁｪｯｶｰ:『I/Oﾁｪｯｸ』",
"WorkItems": [
"1. ①『調整』を選択する",
"2. ②『LCRﾁｪｯｶｰ』を選択する",
"3. ③『FRONT､REAR』を選択する",
"4. ④『開､閉』を選択しﾚﾊﾞｰ動作確認",
"5. ⑤『下降､上昇』を選択しﾚﾊﾞｰ動作確認",
"6. ⑥『廃棄ﾌﾞﾛｰ』を選択しﾚﾊﾞｰ動作確認",
"7. ⑦『部品廃棄BOXを取外し』",
"8. ⑥『廃棄ﾌﾞﾛｰ』を選択する",
"9. 取外した『廃棄BOX』を取付"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合はACTIVATIONｽｲｯﾁを押しながらﾎﾞﾀﾝをﾀｯﾌﾟする",
"※F/R共通作業(仕様に合わせ実施)",
"目視+ｴﾗｰ無き事",
"目視+ｴﾗｰ無き事",
"\"回収ﾌﾞﾛｰ\"でﾌﾞﾛｰON､ｰ定時間後にﾌﾞﾛｰOFFになることを確認する｡音で判断",
"廃棄ﾌﾞﾛｰ\"ON\"でﾌﾞﾛｰしないことを確認",
"『BOXなし』のｴﾗｰﾒｯｾｼﾞが出ることの確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:10_[I/Oﾁｪｯｸ]_No.1_No.2",
"検査表①:10_[I/Oﾁｪｯｸ]_No.3_No.4",
"検査表①:10_[I/Oﾁｪｯｸ]_No.5",
"検査表①:10_[I/Oﾁｪｯｸ]_No.7",
"検査表①:10_[I/Oﾁｪｯｸ]_No.8",
"検査表①:10_[I/Oﾁｪｯｸ]_No.6",
"WEPJ-G002-A03"
]
}
|
{
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り動作する事",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LCRﾁｪｯｶｰ:『動作ｽｲｯﾁ設定』",
"WorkItems": [
"5. ⑤『はい』を選択",
"4. ④『ｷｬﾘﾌﾞﾚｰｼｮﾝ』を選択",
"3. ③『LCRﾁｪｯｸ』をONにする",
"2. ②『LCRﾁｪｯｶｰ』を選択する",
"1. ①『設定』を選択する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LCRﾁｪｯｶｰ:『ｷｬﾘﾌﾞﾚｰｼｮﾝ』ﾒｶ補正",
"WorkItems": [
"1. ①『ｷｬﾘﾌﾞﾚｰｼｮﾝ』を選択する",
"2. ②『第5工程』を選択する",
"4. ④『XYｵﾌｾｯﾄ』を選択する",
"3. ③『実施するﾍｯﾄﾞFRONT､REAR』を選択する",
"5. ⑤『高さｵﾌｾｯﾄ』を選択する",
"6. 指定された位置にﾉｽﾞﾙをｾｯﾄし⑥『実行』を選択する",
"7. ⑦『正常に終了しました』の確認をし⑧を選択",
"8. ⑨を選択する"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合はACTIVATIONｽｲｯﾁを押しながらﾎﾞﾀﾝをﾀｯﾌﾟする",
"ｴﾗｰ無き事",
"ｴﾗｰ無き事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:11_[ﾒｶ補正]_No.1",
"検査表①:11_[ﾒｶ補正]_No.3",
"検査表①:11_[ﾒｶ補正]_No.2",
"データを保存しますか？",
"WEPJ-G002-A03"
]
}
|
{
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り動作する事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LCRﾁｪｯｶｰ:『ｷｬﾘﾌﾞﾚｰｼｮﾝ』電気校正1",
"WorkItems": [
"1. ①『ｷｬﾘﾌﾞﾚｰｼｮﾝ』を選択する",
"2. ②『第5工程』を選択する",
"3. ③『LCR電気校正』を選択する",
"4. ④『実施するﾍｯﾄﾞFRONT､REAR』を選択する",
"5. ⑤『計測準備』を選択する",
"6. 指定された位置にﾉｽﾞﾙをｾｯﾄし､⑥『実行』を選択する",
"7. 指定ｽﾛｯﾄに装着後､⑦『実行』を選択する",
"8. ⑦を選択後､下記画面が表示されるので､内容を確認し､⑧『確認』を選択"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合はACTIVATIONｽｲｯﾁを押しながらﾎﾞﾀﾝをﾀｯﾌﾟする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:12_[電気補正]_No.2",
"検査表①:12_[電気補正]_No1",
"検査表①:12_[電気補正]_No3",
"WEPJ-G002-A03"
]
}
|
{
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り動作する事",
"Method": "-",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LCRﾁｪｯｶｰ:『ｷｬﾘﾌﾞﾚｰｼｮﾝ』電気校正2",
"WorkItems": [
"1. ①『計測ｽﾀｰﾄ』を選択する",
"2. ②『正常に終了しました』を確認する"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合はACTIVATIONｽｲｯﾁを押しながらﾎﾞﾀﾝをﾀｯﾌﾟする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:12_[電気補正]_No.4",
"WEPJ-G002-A03"
]
}
|
{
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り動作する事",
"Method": "-",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LCRﾁｪｯｶｰ:手動測定『定数測定』1",
"WorkItems": [
"1. ①『機種切替』を選択する",
"2. ②『生産ﾃﾞｰﾀ選択』を選択する",
"3. ③『SD』を選択する",
"4. ④ﾃﾞｰﾀを選択する",
"5. ⑤を選択する",
"6. ⑤選択後､下記画面が表示されるので､⑥『はい』を選択する",
"7. ⑦にﾃﾞｰﾀが入っていることを確認",
"8. ⑧『調整』を選択する",
"9. ⑨『ﾍｯﾄﾞ』を選択する",
"10. ﾁｪﾝｼﾞｬｰの⑩『31』に指定ﾉｽﾞﾙをｾｯﾄする"
],
"WorkPoints": [
"ﾃﾞｰﾀの選択は仕様によって変わるため､仕様を確認",
"ﾃﾞｰﾀは『GH_LCR_Check_FC**_#』を選択する(**:16 or 8 or 3)(#:F or R)",
"仕様によってF側かR側が変わるため､仕様を確認",
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合はACTIVATIONｽｲｯﾁを押しながらﾎﾞﾀﾝをﾀｯﾌﾟする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:14_[部品計測]_No1",
"検査表①:14_[部品計測]_No2",
"WEPJ-G002-A03"
]
}
|
{
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LCRﾁｪｯｶｰ:手動測定『定数測定』2",
"WorkItems": [
"1. ﾌｨｰﾀﾞｰに指定部品を取付け､ｽﾛｯﾄ6に装着する",
"2. ①『生産ﾃﾞｰﾀﾃｨｰﾁ』を選択する",
"3. ②『LCRﾁｪｯｶ』を選択する",
"4. ③にﾃﾞｰﾀが入っていることを確認する",
"5. ④『測定開始』を選択する",
"6. ⑤の測定結果を検査書に記入する",
"7. ⑥『ESC』を選択する"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合はACTIVATIONｽｲｯﾁを押しながらﾎﾞﾀﾝをﾀｯﾌﾟする",
"ｽﾛｯﾄ6L:0402R､ｽﾛｯﾄ6R:0402C",
"ｱﾄﾞﾚｽ:6L､部品名:0402R-LCRになっていることを確認",
"測定結果内の計測値を記入する",
"1部品につき､3回計測を行う",
"ｴﾗｰ無き事",
"検査書記載の場合は､小数点2桁まで記載する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:13_[部品計測]_No3",
"検査表①:13_[部品計測]_No4",
"WEPJ-G002-A03"
]
}
|
{
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り動作する事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LCRﾁｪｯｶｰ:手動測定『定数測定』3",
"WorkItems": [
"1. ①を選択する",
"2. ②のﾃﾞｰﾀが変化したか確認する",
"3. ③『測定開始』を選択する",
"4. ④の測定結果を検査書に記入する",
"5. ⑤『ESC』を選択する",
"6. ｺﾝﾀｸﾄﾌﾞﾛｯｸ(治具)を取外し､正規品を再度取付け"
],
"WorkPoints": [
"←ﾎﾞﾀﾝ左上に左記のﾏｰｸがある場合はACTIVATIONｽｲｯﾁを押しながらﾎﾞﾀﾝをﾀｯﾌﾟする",
"ｱﾄﾞﾚｽ:6R､部品名:0402C-LCRになっていることを確認",
"測定結果内の計測値を記入する",
"1部品につき､3回計測を行う",
"ｴﾗｰ無き事",
"検査書記載の場合は､小数点2桁まで記載する事",
"取付け､取外しは下記ﾍﾟｰｼﾞ参照"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:13_[部品計測]_No4",
"【SD-EJM8EH2-503~SD-EJM8EH2-504】参照",
"WEPJ-G002-A03"
]
}
|
{
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り動作する事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "付属品確認",
"WorkItems": [
"1. LCRﾍｯﾄﾞの検査書成績書の検査年月日を記載する",
"2. ｺﾝﾀｸﾄｼｰﾄの製造年月日を記載する"
],
"WorkPoints": [
"(出荷予定日ｰ検査年月日)が10か月以内であること",
"(出荷予定日ｰ検査年月日)が10か月以内であること",
"LOT.NO.から【 AI 】を取ったものが製造年月日写真の場合は｢2019/10/31｣"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:15_[付属品の確認]",
"検査表①:15_[付属品の確認]",
"WEPJ-G002-A03"
]
}
|
{
"QualityItem": "付属品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "付属品が全てある事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"2. 1完成品をBRACKET にBOLT SPACER WASHER で取付ける"
],
"WorkPoints": [
"刻印有り",
"取付方向･位置は下図参照に取付け"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "扉ﾛｯｸｼﾘﾝﾀﾞｰ組立",
"WorkItems": [],
"WorkPoints": [
"CYLINDER とBRACKET の外形を合わせること"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "243cN･m",
"WorkName": "扉ｷｬｯﾁ・ｼｬｯﾀｰ開閉ｽﾄｯﾊﾟｰ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 243cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "243cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "扉ｷｬｯﾁ・ｼｬｯﾀｰ開閉ｽﾄｯﾊﾟｰ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 243cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "100cN･m",
"WorkName": "扉ｷｬｯﾁ・ｼｬｯﾀｰ開閉ｽﾄｯﾊﾟｰ組立",
"WorkItems": [
"3. BRACKET にMAGNET をSCREW で取付ける"
],
"WorkPoints": [
"全体ｶﾊﾞｰ部(SD-A041400-005)で取付け"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｱﾌﾞｿｰﾊﾞｰ組立",
"WorkItems": [
"2. 1完成品にSTOPPER SPACER をBOLT で取付ける",
"1. BRACKET にSHOCK-ABSORBER を付属ﾅｯﾄで取付ける"
],
"WorkPoints": [
"STOPPER の取付けはSPACER BOLT を座ｸﾞﾘ穴側より入れて取付ける事",
"取付け寸法:25㎜±1㎜",
"この作業では同一の物を2個制作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "25㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "80cN･m",
"WorkName": "ｱﾌﾞｿｰﾊﾞｰ組立",
"WorkItems": [
"2. 1完成品にSTOPPER SPACER をBOLT で取付ける",
"1. BRACKET にSHOCK-ABSORBER を付属ﾅｯﾄで取付ける"
],
"WorkPoints": [
"STOPPER の取付けはSPACER BOLT を座ｸﾞﾘ穴側より入れて取付ける事",
"取付け寸法:25㎜±1㎜",
"この作業では同一の物を2個制作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｾｯﾄｸﾗﾝﾌﾟ組立",
"WorkItems": [
"4. 1完成品と3完成品を合わせCOLLAR BOLT で取付ける"
],
"WorkPoints": [
"この状態に合わせる"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"OR",
"◆作業者安全作業",
"OR"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽLCG100",
"WorkName": "ｾｯﾄｸﾗﾝﾌﾟ組立",
"WorkItems": [
"◆3. SPRING にｸﾞﾘｰｽを塗布し2完成品に挿入する"
],
"WorkPoints": [
"両端に近い所に1粒ずつ塗布し全体に馴染ませる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2",
"◆作業者安全作業"
]
}
|
{
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "保持ﾚｰﾙ組立1",
"WorkItems": [
"1. BRACKET BRACKET にPLATE SPACER をBOLT WASHER で取付ける"
],
"WorkPoints": [
"左側用",
"右側用",
"BRACKET BRACKET PLATE の下面を定盤上で合わせて固定",
"左側用",
"右側用",
"左右2個づつ作製の事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"定盤"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽLCG100",
"WorkName": "保持ﾚｰﾙ組立2",
"WorkItems": [
"◆1. SLIDE-RAIL のｷｬｯﾁﾊﾞﾈ部にｸﾞﾘｰｽを塗布する",
"2. 1完成品に をBOLT で仮取付けする"
],
"WorkPoints": [
"表裏のｷｬｯﾁﾊﾞﾈ部に塗布する事",
"左右2個づつ作製の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1",
"◆作業者安全作業"
]
}
|
{
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "194cN･m",
"WorkName": "保持ﾚｰﾙ組立2",
"WorkItems": [],
"WorkPoints": [
" をﾋﾟﾝに当付けｸﾗﾝﾌﾟする",
"SLIDE-RAIL を下に当付けて固定する",
"右側用"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "保持ﾚｰﾙ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5187",
"WorkName": "保持ﾚｰﾙ組立2",
"WorkItems": [],
"WorkPoints": [
" をﾋﾟﾝに当付けｸﾗﾝﾌﾟする",
"SLIDE-RAIL を下に当付けて固定する",
"右側用"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5187",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設置出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｶﾞｲﾄﾞﾚｰﾙ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5186",
"WorkName": "ｶﾞｲﾄﾞﾚｰﾙ組立",
"WorkItems": [
"1. GUIDE にBRACKET をBOLT WASHER で仮取付けする"
],
"WorkPoints": [
"GUIDE を矢印方向に押し当てて固定する",
"BRACKET を矢印方向に押し当てて固定する",
"止めﾈｼﾞにて固定する",
"GUIDE を矢印方向に押し当てて固定する",
"BRACKET を矢印方向に押し当てて固定する",
"取付け向きに注意する:穴が大きい方で取付ける",
"各4ｾｯﾄ作製する",
"止めﾈｼﾞにて固定する",
"SD-A041380-021にて本締結実施"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "設置確認",
"ToolManageNo": "FM-5186",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設置出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "安全SW組立",
"WorkItems": [
"■1. SWITCH の型式確認しﾛｯﾄNo.を記録する",
"3. 2完成品にLABEL を取付ける",
"2. SWITCH のｽｲｯﾁ部とCOVER をBRACKET にBOLT で取付ける"
],
"WorkPoints": [
"ﾛｯﾄNo.",
"ﾛｯﾄNo.",
"型式",
"型式",
"全体ｶﾊﾞｰ組立(SD-A41400-002)で取付け",
"ｽｲｯﾁ部",
"ｱｸﾁｭｴｰﾀ部",
"㉘ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"㉙ｼｯｸﾈｽｹﾞｰｼﾞ",
"㉘㉙を挟み込んで取付けの事",
"S301R"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m",
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表SWITCH :5.前面扉安全SWの型式確認とﾛｯﾄNo.記録",
"WEPJ-G002-C31"
]
}
|
{
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致している事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C31",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "安全SW組立",
"WorkItems": [
"■1. SWITCH の型式確認しﾛｯﾄNo.を記録する",
"3. 2完成品にLABEL を取付ける",
"2. SWITCH のｽｲｯﾁ部とCOVER をBRACKET にBOLT で取付ける"
],
"WorkPoints": [
"ﾛｯﾄNo.",
"ﾛｯﾄNo.",
"型式",
"型式",
"全体ｶﾊﾞｰ組立(SD-A41400-002)で取付け",
"ｽｲｯﾁ部",
"ｱｸﾁｭｴｰﾀ部",
"㉘ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"㉙ｼｯｸﾈｽｹﾞｰｼﾞ",
"㉘㉙を挟み込んで取付けの事",
"S301R"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m",
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表SWITCH :5.前面扉安全SWの型式確認とﾛｯﾄNo.記録",
"WEPJ-G002-C31"
]
}
|
{
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C31",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "100cN･m",
"WorkName": "安全SW組立",
"WorkItems": [],
"WorkPoints": [
"㉘ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"㉙ｼｯｸﾈｽｹﾞｰｼﾞ",
"㉘ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"㉙ｼｯｸﾈｽｹﾞｰｼﾞ"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m",
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "2㎜",
"ToolOther": "",
"WorkName": "安全SW組立",
"WorkItems": [],
"WorkPoints": [
"㉘ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"㉙ｼｯｸﾈｽｹﾞｰｼﾞ"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業"
]
}
|
{
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "2㎜を挟み取付ける事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.5㎜",
"ToolOther": "",
"WorkName": "安全SW組立",
"WorkItems": [],
"WorkPoints": [
"㉘ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"㉙ｼｯｸﾈｽｹﾞｰｼﾞ"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業"
]
}
|
{
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜を挟み取付ける事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付け",
"WorkItems": [
"1. BRACKET にLABEL LABEL を貼付ける"
],
"WorkPoints": [
"150㎜",
"20㎜",
"50㎜",
"127㎜",
"貼付け場所に異物等無き事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立1",
"WorkItems": [
"1. BRACKET PLATE PLATE PLATE をBOLT ･BOLT WASHER ･BOLT WASHER で仮取付けする"
],
"WorkPoints": [
"SD-A041380-012にて本締結実施"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾌﾚｰﾑ組立2",
"WorkItems": [
"1. を定盤上で逆さまに載せて固定する"
],
"WorkPoints": [
"224.3±0.3㎜",
"443.0±0.5㎜",
"定盤との隙間に0.05㎜が入ら無い事を確認する",
"上段",
"中段",
"下段",
"ﾏｶﾞｼﾞﾝ保持部組立台(FM-5090)",
"目安値:下段224.3±0.3㎜､上･下段443.0±0.5㎜",
"各ﾌﾞﾗｹｯﾄ･ﾌﾟﾚｰﾄを矢印方向に当付けて固定する",
"A~Cの冶具をそれぞれの位置にｾｯﾄして調整"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾌﾚｰﾑ組立2",
"WorkItems": [
"1. を定盤上で逆さまに載せて固定する"
],
"WorkPoints": [
"224.3±0.3㎜",
"443.0±0.5㎜",
"定盤との隙間に0.05㎜が入ら無い事を確認する",
"上段",
"中段",
"下段",
"ﾏｶﾞｼﾞﾝ保持部組立台(FM-5090)",
"目安値:下段224.3±0.3㎜､上･下段443.0±0.5㎜",
"各ﾌﾞﾗｹｯﾄ･ﾌﾟﾚｰﾄを矢印方向に当付けて固定する",
"A~Cの冶具をそれぞれの位置にｾｯﾄして調整"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立2",
"WorkItems": [
"1. を定盤上で逆さまに載せて固定する"
],
"WorkPoints": [
"224.3±0.3㎜",
"443.0±0.5㎜",
"定盤との隙間に0.05㎜が入ら無い事を確認する",
"上段",
"中段",
"下段",
"ﾏｶﾞｼﾞﾝ保持部組立台(FM-5090)",
"目安値:下段224.3±0.3㎜､上･下段443.0±0.5㎜",
"各ﾌﾞﾗｹｯﾄ･ﾌﾟﾚｰﾄを矢印方向に当付けて固定する",
"A~Cの冶具をそれぞれの位置にｾｯﾄして調整"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾏｶﾞｼﾞﾝ保持部組立台",
"Size": "",
"ToolOther": "FM-5090",
"WorkName": "ﾌﾚｰﾑ組立2",
"WorkItems": [
"1. を定盤上で逆さまに載せて固定する"
],
"WorkPoints": [
"224.3±0.3㎜",
"443.0±0.5㎜",
"定盤との隙間に0.05㎜が入ら無い事を確認する",
"上段",
"中段",
"下段",
"ﾏｶﾞｼﾞﾝ保持部組立台(FM-5090)",
"目安値:下段224.3±0.3㎜､上･下段443.0±0.5㎜",
"各ﾌﾞﾗｹｯﾄ･ﾌﾟﾚｰﾄを矢印方向に当付けて固定する",
"A~Cの冶具をそれぞれの位置にｾｯﾄして調整"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "設置確認",
"ToolManageNo": "FM-5090",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設置出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾉｷﾞｽ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立2",
"WorkItems": [
"1. を定盤上で逆さまに載せて固定する"
],
"WorkPoints": [
"224.3±0.3㎜",
"443.0±0.5㎜",
"定盤との隙間に0.05㎜が入ら無い事を確認する",
"上段",
"中段",
"下段",
"ﾏｶﾞｼﾞﾝ保持部組立台(FM-5090)",
"目安値:下段224.3±0.3㎜､上･下段443.0±0.5㎜",
"各ﾌﾞﾗｹｯﾄ･ﾌﾟﾚｰﾄを矢印方向に当付けて固定する",
"A~Cの冶具をそれぞれの位置にｾｯﾄして調整"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "下段224.3±0.3㎜、上・下段443.0±0.5㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾌﾚｰﾑ組立3",
"WorkItems": [
"1. にSPACER BOLT ･SCREW WASHER を取付ける",
"2. 1完成品にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"下面",
"中段ﾌﾟﾚｰﾄ",
"上段ﾌﾟﾚｰﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "50cN･m",
"WorkName": "ﾌﾚｰﾑ組立3",
"WorkItems": [
"1. にSPACER BOLT ･SCREW WASHER を取付ける",
"2. 1完成品にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"下面",
"中段ﾌﾟﾚｰﾄ",
"上段ﾌﾟﾚｰﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾌﾚｰﾑ組立4",
"WorkItems": [
"1. にCOVER をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾈｼﾞ穴ｾﾝﾀｰで取付ける",
"ｱﾌﾞｿｰﾊﾞｰ固定部のﾎﾞﾙﾄの逃がし穴を合わせて固定"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾌﾚｰﾑ組立5",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"中段",
"下段",
"下段",
"中段",
"0.1㎜が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰの位置確認"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾌﾞﾗｹｯﾄ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5086",
"WorkName": "ﾌﾚｰﾑ組立5",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"中段",
"下段",
"下段",
"中段",
"0.1㎜が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰの位置確認"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5086",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立5",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"中段",
"下段",
"下段",
"中段",
"0.1㎜が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰの位置確認",
"WEPJ-G002-C31"
]
}
|
{
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜ﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C31",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "100cN･m",
"WorkName": "ﾌﾚｰﾑ組立6",
"WorkItems": [
"1. にPLATE をBOLT で取付ける"
],
"WorkPoints": [
"PLATE のPLATEは外側を幅広側にする",
"PLATE の取付前に油砥石で両面のﾊﾞﾘを除去する事"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "194cN･m",
"WorkName": "保持ﾚｰﾙ取付け",
"WorkItems": [
"1. に をBOLT で取付ける"
],
"WorkPoints": [
"12.1㎜",
"取付け寸法",
"左右のﾏｶﾞｼﾞﾝ保持ﾚｰﾙは固定時下押し当てで固定の事",
"ｽﾗｲﾄﾞﾚｰﾙを動かし取付ける",
"BOLT の丸子ﾈｼﾞは六角穴部が潰れ易いので､摩耗した工具の使用不可"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾏｶﾞｼﾞﾝ保持部の引き出部の位置決め"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "12.1㎜",
"ToolOther": "",
"WorkName": "保持ﾚｰﾙ取付け",
"WorkItems": [
"1. に をBOLT で取付ける"
],
"WorkPoints": [
"12.1㎜",
"取付け寸法",
"左右のﾏｶﾞｼﾞﾝ保持ﾚｰﾙは固定時下押し当てで固定の事",
"ｽﾗｲﾄﾞﾚｰﾙを動かし取付ける",
"BOLT の丸子ﾈｼﾞは六角穴部が潰れ易いので､摩耗した工具の使用不可"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾏｶﾞｼﾞﾝ保持部の引き出部の位置決め",
"WEPJ-G002-C31"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "12.1㎜を挟んで取付ける事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C31",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "保持ﾚｰﾙ連結",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"保持ﾚｰﾙは閉じた状態で取付けの事",
"矢印方向に押し当てて固定する｡上段･下段両方行うこと｡固定後､ﾏｶﾞｼﾞﾝを載せｽﾑｰｽﾞな出し入れと収納が出来る事を確認｡"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｶﾞｲﾄﾞﾚｰﾙ取付け",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"K005-1",
"K005-2",
" と の取付位置",
"BRACKETの向きに注意",
"上方向へ押し当てて取付けの事",
"保持ﾚｰﾙ部に干渉してい無い事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"BRACKETの向きに注意"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｼｬｯﾀｰ開閉ｽﾄｯﾊﾟｰ・ｾｯﾄｸﾗﾝﾌﾟ取付け",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"矢印方向に押し当てて取付けの事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM5519",
"WorkName": "ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"WorkItems": [
"1. に㉖をﾏｶﾞｼﾞﾝ保持部上段に取付ける",
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け、上段と同様に調整する",
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け、上段と同様に調整する"
],
"WorkPoints": [
"ｽﾍﾟｰｻｰ貼付の調整用ﾏｶﾞｼﾞﾝ",
"1.調整用ﾏｶﾞｼﾞﾝはｶﾞﾀ分ｾﾝﾀｰにｾｯﾄする2.調整用ﾏｶﾞｼﾞﾝにｶﾞｲﾄﾞを当付ける3.治具ﾏｶﾞｼﾞﾝにて0.2㎜が通り0.25㎜が通らないことを確認する4.上下左右4ヵ所実施の事",
"1.調整用ﾏｶﾞｼﾞﾝはｶﾞﾀ分ｾﾝﾀｰにｾｯﾄする2.調整用ﾏｶﾞｼﾞﾝにｶﾞｲﾄﾞを当付ける3.治具ﾏｶﾞｼﾞﾝにて0.2㎜が通り0.25㎜が通らないことを確認する4.上下左右4ヵ所実施の事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整"
]
}
|
{
"QualityItem": "設置確認",
"ToolManageNo": "FM5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設置出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "治具ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"WorkItems": [
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け、上段と同様に調整する",
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け、上段と同様に調整する"
],
"WorkPoints": [
"1.調整用ﾏｶﾞｼﾞﾝはｶﾞﾀ分ｾﾝﾀｰにｾｯﾄする2.調整用ﾏｶﾞｼﾞﾝにｶﾞｲﾄﾞを当付ける3.治具ﾏｶﾞｼﾞﾝにて0.2㎜が通り0.25㎜が通らないことを確認する4.上下左右4ヵ所実施の事",
"1.調整用ﾏｶﾞｼﾞﾝはｶﾞﾀ分ｾﾝﾀｰにｾｯﾄする2.調整用ﾏｶﾞｼﾞﾝにｶﾞｲﾄﾞを当付ける3.治具ﾏｶﾞｼﾞﾝにて0.2㎜が通り0.25㎜が通らないことを確認する4.上下左右4ヵ所実施の事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整"
]
}
|
{
"QualityItem": "設置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設置出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.2㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"WorkItems": [
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け、上段と同様に調整する",
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け、上段と同様に調整する"
],
"WorkPoints": [
"1.調整用ﾏｶﾞｼﾞﾝはｶﾞﾀ分ｾﾝﾀｰにｾｯﾄする2.調整用ﾏｶﾞｼﾞﾝにｶﾞｲﾄﾞを当付ける3.治具ﾏｶﾞｼﾞﾝにて0.2㎜が通り0.25㎜が通らないことを確認する4.上下左右4ヵ所実施の事",
"1.調整用ﾏｶﾞｼﾞﾝはｶﾞﾀ分ｾﾝﾀｰにｾｯﾄする2.調整用ﾏｶﾞｼﾞﾝにｶﾞｲﾄﾞを当付ける3.治具ﾏｶﾞｼﾞﾝにて0.2㎜が通り0.25㎜が通らないことを確認する4.上下左右4ヵ所実施の事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"WEPJ-G002-C31"
]
}
|
{
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.2㎜ﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C31",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.2㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"WorkItems": [
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け、上段と同様に調整する",
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け、上段と同様に調整する"
],
"WorkPoints": [
"1.調整用ﾏｶﾞｼﾞﾝはｶﾞﾀ分ｾﾝﾀｰにｾｯﾄする2.調整用ﾏｶﾞｼﾞﾝにｶﾞｲﾄﾞを当付ける3.治具ﾏｶﾞｼﾞﾝにて0.2㎜が通り0.25㎜が通らないことを確認する4.上下左右4ヵ所実施の事",
"1.調整用ﾏｶﾞｼﾞﾝはｶﾞﾀ分ｾﾝﾀｰにｾｯﾄする2.調整用ﾏｶﾞｼﾞﾝにｶﾞｲﾄﾞを当付ける3.治具ﾏｶﾞｼﾞﾝにて0.2㎜が通り0.25㎜が通らないことを確認する4.上下左右4ヵ所実施の事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"WEPJ-G002-C31"
]
}
|
{
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.25㎜ﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C31",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"WorkItems": [
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け、上段と同様に調整する",
"2. ㉖のｻｲﾄﾞの窓より隙間を合わせ固定する",
"3. に㉖をﾏｶﾞｼﾞﾝ保持部下段に取付け、上段と同様に調整する"
],
"WorkPoints": [
"1.調整用ﾏｶﾞｼﾞﾝはｶﾞﾀ分ｾﾝﾀｰにｾｯﾄする2.調整用ﾏｶﾞｼﾞﾝにｶﾞｲﾄﾞを当付ける3.治具ﾏｶﾞｼﾞﾝにて0.2㎜が通り0.25㎜が通らないことを確認する4.上下左右4ヵ所実施の事",
"1.調整用ﾏｶﾞｼﾞﾝはｶﾞﾀ分ｾﾝﾀｰにｾｯﾄする2.調整用ﾏｶﾞｼﾞﾝにｶﾞｲﾄﾞを当付ける3.治具ﾏｶﾞｼﾞﾝにて0.2㎜が通り0.25㎜が通らないことを確認する4.上下左右4ヵ所実施の事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整",
"検査表 :ﾏｶﾞｼﾞﾝｶﾞｲﾄﾞ位置調整"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "治具ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整",
"WorkItems": [
"1. 治具ﾏｶﾞｼﾞﾝを の保持部に挿入しｸﾗﾝﾌﾟする",
"2. ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟとﾏｶﾞｼﾞﾝの間をｼｯｸﾈｽｹﾞｰｼﾞ0.05㎜が通らない様調整する",
"3. 下段側も同様に調整する"
],
"WorkPoints": [
"挿入の際にﾏｶﾞｼﾞﾝﾒｶｽﾄｯﾊﾟｰとﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰの間にｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜を挟み固定する",
"0.05㎜が通ら無い事",
"1.下図の様にﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟ部に3.6㎜のﾌﾞﾛｯｸｹﾞｰｼﾞを挟む2.治具ﾏｶﾞｼﾞﾝとﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの間にｼｯｸﾈｽｹﾞｰｼﾞ0.05㎜が通らないよう位置調整をする※調整後､ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟが傾いてい無い事を確認する",
"ﾏｶﾞｼﾞﾝﾒｶｽﾄｯﾊﾟｰ",
"ﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰ",
"押し当て固定",
"ｼｯｸﾈｽｹﾞｰｼﾞ:0.1㎜",
"ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟ",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ:3.6㎜",
"ｼｯｸﾈｽｹﾞｰｼﾞ:0.05㎜"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整",
"検査表 :ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整"
]
}
|
{
"QualityItem": "設置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設置出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整",
"WorkItems": [
"1. 治具ﾏｶﾞｼﾞﾝを の保持部に挿入しｸﾗﾝﾌﾟする",
"2. ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟとﾏｶﾞｼﾞﾝの間をｼｯｸﾈｽｹﾞｰｼﾞ0.05㎜が通らない様調整する",
"3. 下段側も同様に調整する"
],
"WorkPoints": [
"挿入の際にﾏｶﾞｼﾞﾝﾒｶｽﾄｯﾊﾟｰとﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰの間にｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜を挟み固定する",
"0.05㎜が通ら無い事",
"1.下図の様にﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟ部に3.6㎜のﾌﾞﾛｯｸｹﾞｰｼﾞを挟む2.治具ﾏｶﾞｼﾞﾝとﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの間にｼｯｸﾈｽｹﾞｰｼﾞ0.05㎜が通らないよう位置調整をする※調整後､ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟが傾いてい無い事を確認する",
"ﾏｶﾞｼﾞﾝﾒｶｽﾄｯﾊﾟｰ",
"ﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰ",
"押し当て固定",
"ｼｯｸﾈｽｹﾞｰｼﾞ:0.1㎜",
"ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟ",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ:3.6㎜",
"ｼｯｸﾈｽｹﾞｰｼﾞ:0.05㎜"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整",
"検査表 :ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整"
]
}
|
{
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定の位置に0.1㎜を挟む",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整",
"WorkItems": [
"1. 治具ﾏｶﾞｼﾞﾝを の保持部に挿入しｸﾗﾝﾌﾟする",
"2. ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟとﾏｶﾞｼﾞﾝの間をｼｯｸﾈｽｹﾞｰｼﾞ0.05㎜が通らない様調整する",
"3. 下段側も同様に調整する"
],
"WorkPoints": [
"挿入の際にﾏｶﾞｼﾞﾝﾒｶｽﾄｯﾊﾟｰとﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰの間にｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜を挟み固定する",
"0.05㎜が通ら無い事",
"1.下図の様にﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟ部に3.6㎜のﾌﾞﾛｯｸｹﾞｰｼﾞを挟む2.治具ﾏｶﾞｼﾞﾝとﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの間にｼｯｸﾈｽｹﾞｰｼﾞ0.05㎜が通らないよう位置調整をする※調整後､ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟが傾いてい無い事を確認する",
"ﾏｶﾞｼﾞﾝﾒｶｽﾄｯﾊﾟｰ",
"ﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰ",
"押し当て固定",
"ｼｯｸﾈｽｹﾞｰｼﾞ:0.1㎜",
"ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟ",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ:3.6㎜",
"ｼｯｸﾈｽｹﾞｰｼﾞ:0.05㎜"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整",
"検査表 :ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整",
"WEPJ-G002-C31"
]
}
|
{
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜ﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C31",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "3.6㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整",
"WorkItems": [
"3. 下段側も同様に調整する"
],
"WorkPoints": [
"ﾏｶﾞｼﾞﾝﾒｶｽﾄｯﾊﾟｰ",
"ﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰ",
"押し当て固定",
"ｼｯｸﾈｽｹﾞｰｼﾞ:0.1㎜",
"ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟ",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ:3.6㎜",
"ｼｯｸﾈｽｹﾞｰｼﾞ:0.05㎜"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整"
]
}
|
{
"QualityItem": "設置確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り設置出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整",
"WorkItems": [
"3. 下段側も同様に調整する"
],
"WorkPoints": [
"ﾏｶﾞｼﾞﾝﾒｶｽﾄｯﾊﾟｰ",
"ﾏｶﾞｼﾞﾝｽﾄｯﾊﾟｰ",
"押し当て固定",
"ｼｯｸﾈｽｹﾞｰｼﾞ:0.1㎜",
"ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟ",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ:3.6㎜",
"ｼｯｸﾈｽｹﾞｰｼﾞ:0.05㎜"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾏｶﾞｼﾞﾝｸﾗﾝﾌﾟの調整"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "扉開閉ﾊﾞﾙﾌﾞ・扉ﾛｯｸｼﾘﾝﾀﾞｰ取付け",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"矢印方向に押し当てて取付けの事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "194cN･m",
"WorkName": "ｺﾈｸﾀﾌﾞﾗｹｯﾄ・安全SW取付け",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"矢印方向に押し当て取付けの事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾊﾞｰ用POST取付け",
"WorkItems": [
"1. にPOST をBOLT WASHER で仮取付けする",
"2. 1完成品にPOST をBOLT WASHER で仮取付けする"
],
"WorkPoints": [
"Hｶｯﾄ部を縦方向に固定する｡POST POST の長さが違うので取付位置に注意",
"Hｶｯﾄ部を縦方向に固定する｡POST POST の長さが違うので取付位置に注意",
"SD-A041086-712にて本締結実施",
"SD-A041086-710にて本締結実施"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "扉用ﾏｸﾞﾈｯﾄ・ｷｬｯﾁ取付け",
"WorkItems": [
"1. に をPLATE BOLT WASHER で仮取付けする",
"2. 1完成品に をWASHER BOLT で仮取付けする"
],
"WorkPoints": [
"矢印方向へ押し当てて仮固定する",
"矢印方向へ押し当てて仮固定する",
"SD-A041086-403にて本締結実施",
"SD-A041086-404にて本締結実施"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FT4取付け",
"WorkItems": [
"1. にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"右側面",
"ｲﾝｼｭﾛｯｸ挿入方向を下図参照に向ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "連結用ﾌﾞﾗｹｯﾄ・ｶﾞｲﾄﾞﾌﾞﾛｯｸ取付け",
"WorkItems": [
"1. にBRACKET を左右上部にBOLT WASHER で取付ける",
"2. 1完成品にBLOCK をSPACER BOLT WASHER で取付ける"
],
"WorkPoints": [
"左側",
"BRACKET を仮取付け後､治具FM-5216に押し当てて位置決めし締結する",
"SD-A041086-402にて本締結実施",
"右側"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾏｶﾞｼﾞﾝ保持部ﾌﾞﾗｹｯﾄ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5216",
"WorkName": "連結用ﾌﾞﾗｹｯﾄ・ｶﾞｲﾄﾞﾌﾞﾛｯｸ取付け",
"WorkItems": [
"1. にBRACKET を左右上部にBOLT WASHER で取付ける",
"2. 1完成品にBLOCK をSPACER BOLT WASHER で取付ける"
],
"WorkPoints": [
"左側",
"右側",
"BRACKET を仮取付け後､治具FM-5216に押し当てて位置決めし締結する",
"SD-A041086-402にて本締結実施"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "設置確認",
"ToolManageNo": "FM-5216",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設置出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｹｰﾌﾞﾙﾍﾞｱﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ｹｰﾌﾞﾙﾍﾞｱﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"2. 1完成品にJOINT をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｴｱｰ配管接続",
"WorkItems": [
"1. JOINT にJOINT を挿入する",
"2. TUBE を指定の長さにｶｯﾄし､1完成品に挿入する",
"3. 2完成品を に挿入する"
],
"WorkPoints": [
"100㎜",
"70㎜",
"外側よりﾀﾞﾌﾞﾙｿﾚﾉｲﾄﾞとｼﾝｸﾞﾙｿﾚﾉｲﾄﾞに短い方を各1本ずつ､一番内側のｼﾝｸﾞﾙｿﾚﾉｲﾄﾞに長いﾁｭｰﾌﾞを挿入する｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｴｱｰ配管接続",
"WorkItems": [
"1. JOINT にJOINT を挿入する",
"2. TUBE を指定の長さにｶｯﾄし､1完成品に挿入する",
"3. 2完成品を に挿入する"
],
"WorkPoints": [
"100㎜",
"70㎜",
"外側よりﾀﾞﾌﾞﾙｿﾚﾉｲﾄﾞとｼﾝｸﾞﾙｿﾚﾉｲﾄﾞに短い方を各1本ずつ､一番内側のｼﾝｸﾞﾙｿﾚﾉｲﾄﾞに長いﾁｭｰﾌﾞを挿入する｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾌﾛﾝﾄﾌﾚｰﾑﾋﾟﾝ圧入ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4882",
"WorkName": "YZﾋﾟﾝ圧入",
"WorkItems": [
"1. FRAME(A) にPIN を圧入する",
"2. PIN をSCREW を固定する"
],
"WorkPoints": [
"圧入前､FRAME(A) 下面に砥石を掛けておく"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-4882",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "50cN･m",
"WorkName": "YZﾋﾟﾝ圧入",
"WorkItems": [
"1. FRAME(A) にPIN を圧入する",
"2. PIN をSCREW を固定する"
],
"WorkPoints": [
"圧入前､FRAME(A) 下面に砥石を掛けておく"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X位置決めﾋﾟﾝ取付",
"WorkItems": [
"1. にPIN をNUT WASHER で仮止めする"
],
"WorkPoints": [
"｢SD-A000501-306｣で本締め",
"ﾏｲﾅｽの溝を横方向にしておく"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ALﾌﾛﾝﾄﾌﾚｰﾑPIN圧入治具",
"Size": "",
"ToolOther": "FM-4421",
"WorkName": "Fﾌﾚｰﾑﾋﾟﾝ圧入",
"WorkItems": [
"1. にPIN を圧入する"
],
"WorkPoints": [
"ﾋﾟﾝ出代:3.5㎜ 治具より高く出ていないこと",
"PIN の細いほうを 側に圧入",
"ﾌﾚｰﾑ下面に突き出ないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "PIN出代",
"ToolManageNo": "FM-4421",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.5㎜",
"Method": "目視手感",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ALﾘｱﾌﾚｰﾑPIN圧入治具",
"Size": "",
"ToolOther": "FM-4422",
"WorkName": "Rﾌﾚｰﾑﾋﾟﾝ圧入",
"WorkItems": [
"1. FRAME(B) にPIN PIN を圧入する"
],
"WorkPoints": [
"治具をｾｯﾄしてﾋﾟﾝを入れる",
"上から治具を被せて圧入する",
"ﾋﾟﾝ出代:3.0㎜下側治具より高く出ていないこと",
"PIN の細いほうをFRAME(B) 側に圧入",
"PIN の引っ掛け側を上側に圧入",
"ﾋﾟﾝ出代:5.2㎜上側治具で隙間なく押えていること",
"ﾌﾚｰﾑ下面に突き出ないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "PIN出代",
"ToolManageNo": "FM-4422",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5.2㎜出代:3.0㎜",
"Method": "目視手感",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ALﾘｱﾌﾚｰﾑPIN圧入治具",
"Size": "",
"ToolOther": "FM-4423",
"WorkName": "Rﾌﾚｰﾑﾋﾟﾝ取付け",
"WorkItems": [
"1. にPIN を圧入する"
],
"WorkPoints": [
"突き当たりまで圧入する",
" に治具を取付ける",
"PIN の上に治具を乗せて圧入する",
"青い穴にPIN を入れる",
"PIN の引っ掛け側を上側に圧入",
"㉗のピンを丸位置に挿入"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-4423",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾋﾟﾝ圧入治具",
"Size": "",
"ToolOther": "FM-3913",
"WorkName": "Tｽﾛｯﾄﾋﾟﾝ圧入",
"WorkItems": [
"1. RAIL にｱﾙｶﾝｻｽをかけてﾊﾞﾘ等取り除く",
"2. ㉘にRAIL をセットする",
"3. ㉘の付属品を乗せる"
],
"WorkPoints": [
"2本作製のこと",
"RAIL の斜めに加工している側を作業者側から見て右になるようにｾｯﾄする",
"出代1.8㎜ ﾋﾟﾝ圧入方向に注意 下面に突き出さないこと",
"治具より高く出ていないこと",
"PIN の細いほうを➀側に圧入"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "PIN出代方向確認",
"ToolManageNo": "FM-3913",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:1.8㎜",
"Method": "目視手感",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾍﾞｱﾘﾝｸﾞ圧入治具",
"Size": "",
"ToolOther": "FM-4105",
"WorkName": "ﾍﾞｱﾘﾝｸﾞ圧入1",
"WorkItems": [
"1. STOPPER にBEARING orBEARING とBEARING を圧入する"
],
"WorkPoints": [
"治具にSTOPPER を乗せる",
"STOPPER にBEARING ･BEARING を乗せる",
"BEARING ･BEARING の上に治具を被せて圧入する",
"BEARING ･BEARING の端面をこちら側の面に合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-4105",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "box4㎜",
"ToolOther": "20cN･m",
"WorkName": "ﾚﾊﾞｰ組立",
"WorkItems": [
"1. PIN を治具に乗せて､ WASHER LEVER の順で乗せていきNUT で固定する"
],
"WorkPoints": [
"治具にPIN を入れる",
"PIN の上に を乗せる",
" の上にWASHER を乗せる",
"WASHER の上にLEVER を乗せる",
"NUT を乗せて固定する"
],
"Tolks": [
"締付ﾄﾙｸ 20cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾚﾊﾞｰ部組立治具",
"Size": "",
"ToolOther": "FM-4399",
"WorkName": "ﾚﾊﾞｰ組立",
"WorkItems": [
"1. PIN を治具に乗せて､ WASHER LEVER の順で乗せていきNUT で固定する"
],
"WorkPoints": [
"治具にPIN を入れる",
"PIN の上に を乗せる",
" の上にWASHER を乗せる",
"WASHER の上にLEVER を乗せる",
"NUT を乗せて固定する"
],
"Tolks": [
"締付ﾄﾙｸ 20cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-4399",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾍﾞｱﾘﾝｸﾞ圧入治具",
"Size": "",
"ToolOther": "FM-4398",
"WorkName": "ﾍﾞｱﾘﾝｸﾞ圧入2",
"WorkItems": [
"1. LEVER にBEARING orBEARING を圧入する"
],
"WorkPoints": [
"LEVER とBEARING の端面を合わせる",
"この面よりﾍﾞｱﾘﾝｸﾞがはみ出していないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-4398",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾎｲｰﾙ組立台",
"Size": "",
"ToolOther": "FM-4407",
"WorkName": "落下防止ｷﾞｱ組立1",
"WorkItems": [
"1. WHEEL にCLUTCH を圧入する",
"2. 上記完成品にWHEEL をSCREW で取付ける"
],
"WorkPoints": [
"圧入する",
"ｼﾞｸﾞにWHEEL を乗せる",
"回転方向の矢印が見える様にCLUTCH を置く",
"WHEEL の凸部とCLUTCH の凹部の位置合わせをする",
"樹脂の凸部とWHEEL の穴を合わせる事",
"ﾈｼﾞが届かない場合は治具上で作業する事",
"WHEEL は表裏あり",
"CLUTCH は表裏あり"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-4407",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "+№1",
"ToolOther": "15cN･m",
"WorkName": "落下防止ｷﾞｱ組立1",
"WorkItems": [
"2. 上記完成品にWHEEL をSCREW で取付ける"
],
"WorkPoints": [
"樹脂の凸部とWHEEL の穴を合わせる事",
"ﾈｼﾞが届かない場合は治具上で作業する事",
"WHEEL は表裏あり",
"CLUTCH は表裏あり"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "60cN･m",
"WorkName": "落下防止ｷﾞｱ組立2",
"WorkItems": [
"2. ㉗（左側）に上記完成品、 、COLLAR の順番でセットし、SCREW で締結し、CAP を取付ける"
],
"WorkPoints": [
"PIN の凹部を上向きにｾｯﾄする",
"回転方向",
" ,COLLAR を写真の向きでｾｯﾄする事",
"BRACKET の凸部にPIN の凹部が乗り上げていないか確認"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "落下防止ｷﾞｱ組立2",
"WorkItems": [
"1. ㉗（右側）にPIN BRACKET の順番で下記写真のようにセットし、SCREW で締結する",
"2. ㉗（左側）に上記完成品、 、COLLAR の順番でセットし、SCREW で締結し、CAP を取付ける"
],
"WorkPoints": [
"PIN の凹部を上向きにｾｯﾄする",
"回転方向",
" ,COLLAR を写真の向きでｾｯﾄする事",
"BRACKET の凸部にPIN の凹部が乗り上げていないか確認"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾃｰﾌﾟ落下防止ｷﾞｱ組立台",
"Size": "",
"ToolOther": "FM-5587",
"WorkName": "落下防止ｷﾞｱ組立2",
"WorkItems": [
"2. ㉗（左側）に上記完成品、 、COLLAR の順番でセットし、SCREW で締結し、CAP を取付ける"
],
"WorkPoints": [
"PIN の凹部を上向きにｾｯﾄする",
"回転方向",
" ,COLLAR を写真の向きでｾｯﾄする事",
"BRACKET の凸部にPIN の凹部が乗り上げていないか確認"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5587",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾏｲﾅｽ幅7㎜",
"ToolOther": "40cN･m",
"WorkName": "ﾃｰﾌﾟｶﾞｲﾄﾞ押さえﾚﾊﾞｰ組立",
"WorkItems": [
"1. 治具にSPACER を乗せ､LEVER WASHER BEARING orBEARING を置いてPIN で固定する",
"2. 上記完成品にPLATE をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾃｰﾌﾟ押えﾚﾊﾞｰ部組立治具",
"Size": "",
"ToolOther": "FM-4403",
"WorkName": "ﾃｰﾌﾟｶﾞｲﾄﾞ押さえﾚﾊﾞｰ組立",
"WorkItems": [
"1. 治具にSPACER を乗せ､LEVER WASHER BEARING orBEARING を置いてPIN で固定する",
"2. 上記完成品にPLATE をSCREW で取付ける",
"1. 治具にSPACER を乗せ､LEVER WASHER BEARING orBEARING を置いてPIN で固定する",
"2. 上記完成品にPLATE をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-4403",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾏｲﾅｽ幅7㎜",
"ToolOther": "40cN･m",
"WorkName": "ﾃｰﾌﾟｶﾞｲﾄﾞ押さえﾚﾊﾞｰ組立",
"WorkItems": [
"1. 治具にSPACER を乗せ､LEVER WASHER BEARING orBEARING を置いてPIN で固定する",
"2. 上記完成品にPLATE をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "+№0",
"ToolOther": "22cN･m",
"WorkName": "ｱｸﾁｭｴｰﾀｰ組立",
"WorkItems": [
"1. SOLENOID-ACTUATOR から先端部のﾋﾟｽﾄﾝを抜いておく",
"3. 完成品を治具に取付け固定する"
],
"WorkPoints": [
"ﾋﾟｽﾄﾝは取付け時に使用する為廃棄し無い事",
"ｱｸﾁｭｴｰﾀｰの穴とｼﾞｸﾞの凸部とｱｸﾁｭｴｰﾀｰの凸部とｼﾞｸﾞの凹部を合わせる",
"｢SD-A000501-508｣で取付",
"引いてｾｯﾄする",
"締結終了後､引いてｸﾗﾝﾌﾟ解除して取り外す"
],
"Tolks": [
"締付ﾄﾙｸ 22cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "22cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｱｸﾁｭｴｰﾀ組付治具",
"Size": "",
"ToolOther": "FM-4400",
"WorkName": "ｱｸﾁｭｴｰﾀｰ組立",
"WorkItems": [
"1. SOLENOID-ACTUATOR から先端部のﾋﾟｽﾄﾝを抜いておく",
"3. 完成品を治具に取付け固定する"
],
"WorkPoints": [
"ﾋﾟｽﾄﾝは取付け時に使用する為廃棄し無い事",
"ｱｸﾁｭｴｰﾀｰの穴とｼﾞｸﾞの凸部とｱｸﾁｭｴｰﾀｰの凸部とｼﾞｸﾞの凹部を合わせる",
"｢SD-A000501-508｣で取付",
"引いてｾｯﾄする",
"締結終了後､引いてｸﾗﾝﾌﾟ解除して取り外す"
],
"Tolks": [
"締付ﾄﾙｸ 22cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-4400",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "+No.0",
"ToolOther": "25cN･m",
"WorkName": "ﾃｰﾌﾟ矯正ｶﾞｲﾄﾞ組立",
"WorkItems": [
"3. 本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 25cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "25cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "矯正ｶﾞｲﾄﾞねじ締めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4781",
"WorkName": "ﾃｰﾌﾟ矯正ｶﾞｲﾄﾞ組立",
"WorkItems": [
"2. 1.完成品を㉘にセットする",
"4. ﾚﾊﾞｰを戻して完成品を取り外す",
"3. 本締めする",
"2. 1.完成品を㉘にセットする",
"4. ﾚﾊﾞｰを戻して完成品を取り外す"
],
"WorkPoints": [
"ｸﾗﾝﾌﾟ部を開いて入れる",
"ﾚﾊﾞｰを倒してｸﾗﾝﾌﾟさせる",
"ｸﾗﾝﾌﾟ部を開いて入れる",
"ﾚﾊﾞｰを倒してｸﾗﾝﾌﾟさせる"
],
"Tolks": [
"締付ﾄﾙｸ 25cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-4781",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "中継基盤組立",
"WorkItems": [
"1. LED-LAMP-UNIT のｹｰﾌﾞﾙをBOARD のｺﾈｸﾀに取付ける"
],
"WorkPoints": [
"LED-LAMP-UNIT の挿入方向に注意",
"ｺﾈｸﾀを接続したら青ﾏｰｷﾝｸﾞをする",
"色が薄い部分が､1mm程度出ている"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "+№2",
"ToolOther": "60cN･m",
"WorkName": "ﾃｰﾌﾟ規正ｶﾞｲﾄﾞ組立1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ規正ｶﾞｲﾄﾞ組立1",
"WorkItems": [
"1. ㉘にGUIDE GUIDE ,BRACKET ,PLATE の順番で写真のように置き、SCREW で締結",
"2.上記､完成品を反転させ､PLATE を置き､SCREW にて締結"
],
"WorkPoints": [
"GUIDE :段ありが上",
"GUIDE :向きはどちらでも可",
"㉘を反対の手で押さえながら締結の事"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾃｰﾌﾟ規制ｶﾞｲﾄﾞ組立台",
"Size": "",
"ToolOther": "FM-5582",
"WorkName": "ﾃｰﾌﾟ規正ｶﾞｲﾄﾞ組立1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5582",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ規正ｶﾞｲﾄﾞ組立2",
"WorkItems": [
"1. にBOLT NUT を取付ける"
],
"WorkPoints": [
"締め込ま無い事(本締めはSD-A000501-531)",
"目安寸法2~2.5mm",
"ﾅｯﾄ取付け方向図示のこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾗｯﾄ面",
"挿入方向"
]
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:2~2.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ規正ｶﾞｲﾄﾞ組立3",
"WorkItems": [
"1. COVER にBLOCK KIT を貼付ける"
],
"WorkPoints": [
"16.5㎜±0.5㎜",
"2㎜±0.5㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:16.5±0.5㎜2±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾊｻﾐ",
"Size": "小",
"ToolOther": "CANARY:DS-100",
"WorkName": "ﾏｸﾞﾈｯﾄ準備",
"WorkItems": [
"1. MAGNET を㉗で１つずつに切り分ける",
"2. MAGNET MAGNET を㉖で１つずつに切り分ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "切断確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "両面ﾃｰﾌﾟが切れている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾏｸﾞﾈｯﾄ貼付けｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5610",
"WorkName": "ｽﾌﾟﾘﾝｸﾞﾌﾟﾚｰﾄ組立2",
"WorkItems": [
"1. ㉖のブロックを持ち上げてSPRING-PLATE を取付ける。",
"2. SPRING-PLATE に を取付ける｡"
],
"WorkPoints": [
"2段に曲げているほうが左側",
"奥に押し当てる",
"ﾉﾌﾞを回してSPRING-PLATE を規正する",
"左のﾌﾞﾛｯｸに当付け",
" に当付け",
"上げる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "隙間確認",
"ToolManageNo": "FM-5610",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾏｸﾞﾈｯﾄ貼付けｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5610",
"WorkName": "ｽﾌﾟﾘﾝｸﾞﾌﾟﾚｰﾄ組立3",
"WorkItems": [
"1. ㉖のカバーを下す",
"2. ③を貼付ける"
],
"WorkPoints": [
"中のﾏｸﾞﾈｯﾄに当付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
}
|
{
"QualityItem": "隙間確認",
"ToolManageNo": "FM-5610",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
}
|
information_extraction
|
0
| null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.