input stringclasses 1
value | instruction stringlengths 222 1.92k | output stringlengths 193 312 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "配管準備挿入",
"WorkItems": [
"1. TUBE を指定寸法にｶｯﾄする",
"2. に1完成品(№101)を取付ける",
"3. TUBE を指定寸法にｶｯﾄする",
"4. に3完成品(№201)を取付ける",
"5. に4完成品(№202)を取付ける",
"1. TUBE を指定寸法にｶｯﾄする",
"2. に1完成品(№101)を取付ける",
"3. TUBE... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｼｬｯﾀｰ部の配線配管の整線",
"WorkItems": [
"1. 開閉シャッター部の配線配管の整線を行い㉖で固定する"
],
"WorkPoints": [
"駆動部が 6㎜ 昇降するため配線配管に余裕を持たせる事",
"余裕を持たせる事",
"配線",
"配管",
"㉖の頭の位置に注意する",
"ｺﾈｸﾀｰの寸法を確認して整線を行う事",
"配線配管の固定に注意する... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ検査治具",
"Size": "",
"ToolOther": "FM-6229",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ検査治具接続-①",
"WorkItems": [
"1. に㉖の各センサーを接続する",
"2. に㉖の配管を各バルブに接続する"
],
"WorkPoints": [
"ｼｬｯﾀｰ開閉ｾﾝｻｰ(開:B01P､閉:B02P)",
"ﾁｪﾝｼﾞｬｰ有無ｾﾝｻｰ(B03R)",
"ﾁｪﾝｼﾞｬｰ昇降ｾﾝｻｰ(上昇:B04R､下降:B05R)",
"... | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-6229",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ検査治具",
"Size": "",
"ToolOther": "FM-6229",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ検査治具接続-②",
"WorkItems": [
"1. ㉖の電源を投入する"
],
"WorkPoints": [
"手順1:POWERをONする",
"手順2:ﾓﾆﾀｰの指示に従いSTART SWを押す",
"ｾｯﾄｱｯﾌﾟ完了です",
"指の挟み込みに注意して検査を実施してください"
],
"Tolks": [],
"Inspecti... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-6229",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ検査治具",
"Size": "",
"ToolOther": "FM-6229",
"WorkName": "昇降ｼﾘﾝﾀﾞｰ調整",
"WorkItems": [
"1. に㉖を繋ぎ駆動ユニットを上昇させる",
"2. のﾁｪﾝｼﾞｬｰ搭載面の高さ測定を行う"
],
"WorkPoints": [
"寸法測定箇所（チェンジャー搭載面中央）✖印",
"相対寸法測定箇所（チェンジャー搭載面中央）✖印",
" の駆動ﾕﾆｯﾄを何度か昇降させｽﾑｰｽﾞに動作する事",
"ｽﾃｰｼﾞ... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-6229",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降ｼﾘﾝﾀﾞｰ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "上昇限:94.50±0.05㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "昇降ｼﾘﾝﾀﾞｰ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WEPJ-G002-C07"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "上昇限:94.50±0.05㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C07",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ｼﾘﾝﾀﾞｰ調整",
"WorkItems": [
"1. に㉖を繋ぎ駆動ユニットを上昇させる",
"2. のﾁｪﾝｼﾞｬｰ搭載面の高さ測定を行う"
],
"WorkPoints": [
"寸法測定箇所（チェンジャー搭載面中央）✖印",
"相対寸法測定箇所（チェンジャー搭載面中央）✖印",
" の駆動ﾕﾆｯﾄを何度か昇降させｽﾑｰｽﾞに動作する事",
"ｽﾃｰｼﾞ昇降用ｼﾘﾝﾀﾞｰの上昇... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "上昇限:94.50±0.05㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C07",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "17㎜",
"ToolOther": "20.0N･m",
"WorkName": "昇降ｼﾘﾝﾀﾞｰ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱｰ供給治具ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ検査治具",
"Size": "",
"ToolOther": "FM-2823FM-6229",
"WorkName": "昇降ｾﾝｻｰ検出確認",
"WorkItems": [
"1. の ｽﾃｰｼﾞ昇降ﾌｫﾄｾﾝｻｰの調整を行う"
],
"WorkPoints": [
"ｽﾃｰｼﾞの昇降時ﾌｫﾄｾﾝｻｰが検知している事(同時ON無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"Inspecti... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2823FM-6229",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上限/下限位置でそれぞれON/OFFする事(同時ON無い事)",
"Method": "PHﾁｪｯｶｰ",
"RecordMethod": "WEPJ-G002-C07",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ｾﾝｻｰ検出確認",
"WorkItems": [
"1. の ｽﾃｰｼﾞ昇降ﾌｫﾄｾﾝｻｰの調整を行う"
],
"WorkPoints": [
"ｽﾃｰｼﾞの昇降時ﾌｫﾄｾﾝｻｰが検知している事(同時ON無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes":... | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "上限/下限位置でそれぞれON/OFFする事(同時ON無い事)",
"Method": "PHﾁｪｯｶｰ",
"RecordMethod": "WEPJ-G002-C07",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "昇降ｾﾝｻｰ検出確認",
"WorkItems": [
"1. の ｽﾃｰｼﾞ昇降ﾌｫﾄｾﾝｻｰの調整を行う"
],
"WorkPoints": [
"ｽﾃｰｼﾞの昇降時ﾌｫﾄｾﾝｻｰが検知している事(同時ON無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ検査治具",
"Size": "",
"ToolOther": "FM-6229",
"WorkName": "ﾕﾆｯﾄｽﾃｰｼﾞ昇降ｽﾋﾟｺﾝ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WEPJ-G002-C07"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-6229",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "上昇時:200~250ms下降時:150~200ms",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C07",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "0.3N･m",
"WorkName": "ﾕﾆｯﾄｽﾃｰｼﾞ昇降ｽﾋﾟｺﾝ調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "0.3N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6239",
"WorkName": "ﾗﾍﾞﾙ貼付け",
"WorkItems": [
"1. にLABEL を貼付ける",
"2. に⑦を貼付ける"
],
"WorkPoints": [
"LABEL 矢印の方向に注意",
"可動ﾌﾟﾚｰﾄ(上部)に貼付ける事",
"⑦の貼付方向に注意",
"ﾍﾞｰｽﾌﾟﾚｰﾄ(下部)に貼付ける事"
],
"Tolks": [],
"InspectionNo... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6239",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け",
"WorkItems": [],
"WorkPoints": [
"LABEL 矢印の方向に注意",
"可動ﾌﾟﾚｰﾄ(上部)に貼付ける事",
"⑦の貼付方向に注意",
"ﾍﾞｰｽﾌﾟﾚｰﾄ(下部)に貼付ける事",
"LABEL 矢印の方向に注意",
"可動ﾌﾟﾚｰﾄ(上部)に貼付ける事",
"⑦の貼付方向に注意",
"ﾍﾞｰｽﾌﾟﾚｰﾄ(下部)に貼付ける事"
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "払い出し準備",
"WorkItems": [
"1. JOINT BOLT WASHER WASHER を3工程前準備工程に引き渡す",
"2. BOLT を3工程前準備工程に引き渡す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞｱﾘﾝｸﾞ､Dﾋﾟﾝ圧入治具",
"Size": "",
"ToolOther": "FM-2250",
"WorkName": "本組立前準備①",
"WorkItems": [
"1. BEARING にPIN を圧入"
],
"WorkPoints": [
"｢8.12ﾉｽﾞﾙ｣側を使用する 刻印注意",
"治具のﾋﾟﾝがある方にﾍﾞｱﾘﾝｸﾞをｾｯﾄする",
"ﾃｰﾊﾟｰ側を上にして挿入"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIt... | {
"QualityItem": "圧入確認",
"ToolManageNo": "FM-2250",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り圧入出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊﾞﾈｶﾞｲﾄﾞDﾋﾟﾝ圧入治具",
"Size": "",
"ToolOther": "FM-2252",
"WorkName": "本組立前準備②",
"WorkItems": [
"▲1. PIN に接着剤を塗布しBLOCK に圧入"
],
"WorkPoints": [
"圧入後､指で引っ張り抜け無い事を確認",
"ﾋﾟﾝのﾃｰﾊﾟ側に塗布する事",
"治具BLOCK にPIN を挿入する",
"治具PIN にBLOCK を挿入し圧入する",
"ﾋﾟﾝ出代:39㎜"
],
"Tolk... | {
"QualityItem": "圧入確認",
"ToolManageNo": "FM-2252",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り圧入出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本組立前準備②",
"WorkItems": [
"▲1. PIN に接着剤を塗布しBLOCK に圧入"
],
"WorkPoints": [
"圧入後､指で引っ張り抜け無い事を確認",
"ﾋﾟﾝのﾃｰﾊﾟ側に塗布する事",
"治具BLOCK にPIN を挿入する",
"治具PIN にBLOCK を挿入し圧入する",
"ﾋﾟﾝ出代:39㎜"
],
"Tolks": [],
"Inspection... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "剥がれ無き事米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "接着剤ﾛｯｸﾀｲﾄ242/243",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "本組立前準備②",
"WorkItems": [
"▲1. PIN に接着剤を塗布しBLOCK に圧入"
],
"WorkPoints": [
"圧入後､指で引っ張り抜け無い事を確認",
"ﾋﾟﾝのﾃｰﾊﾟ側に塗布する事",
"治具BLOCK にPIN を挿入する",
"治具PIN にBLOCK を挿入し圧入する",
"ﾋﾟﾝ出代:39㎜"
],
"Tolks": [],
"Ins... | {
"QualityItem": "ﾋﾟﾝ出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:39㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "本組立前準備③",
"WorkItems": [
"1. BLOCK に砥石を掛ける",
"2. 1完成品にPIN を圧入"
],
"WorkPoints": [
"ﾋﾟﾝ圧入面の裏表面に掛ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-22... | {
"QualityItem": "ﾋﾟﾝ出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:両端3㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "位置決めﾌﾞﾛｯｸ打込み治具",
"Size": "",
"ToolOther": "FM-2253",
"WorkName": "本組立前準備③",
"WorkItems": [
"1. BLOCK に砥石を掛ける",
"2. 1完成品にPIN を圧入"
],
"WorkPoints": [
"ﾋﾟﾝ圧入面の裏表面に掛ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": ... | {
"QualityItem": "圧入確認",
"ToolManageNo": "FM-2253",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り圧入出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立①",
"WorkItems": [
"1. BASE に油砥石(ｱﾙﾐ用)をかける"
],
"WorkPoints": [
"加工面をかけ､ﾊﾞﾘがないか確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"表面",
"裏面"
]
} | {
"QualityItem": "ﾊﾞﾘ確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘがないか確認",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立②",
"WorkItems": [
"1. にPIN を圧入"
],
"WorkPoints": [
"ﾋﾟﾝ出代:1.5㎜",
"座ｸﾞﾘ有りが表面",
"ﾃｰﾊﾟｰ側を圧入"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"表面... | {
"QualityItem": "ﾋﾟﾝ出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:1.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立③",
"WorkItems": [
"1. にSPACER を通し に圧入"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "圧入確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り圧入出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾎﾙﾀﾞ取付",
"WorkItems": [
"1. にHOLDER をBOLT で取付"
],
"WorkPoints": [
"ﾍﾞｰｽのDﾋﾟﾝに挿入した後､ﾎﾞﾙﾄを締結"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾍﾞｱﾘﾝｸﾞ取付",
"WorkItems": [
"1. BOLT にBEARING SPACER を通し に取付",
"2. BOLT にSPACER を通し に取付",
"1. BOLT にBEARING SPACER を通し に取付",
"2. BOLT にSPACER を通し に取付"
],
"WorkPoints": [],
"Tolks": [],
"Inspecti... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾌﾞﾛｯｸ取付①",
"WorkItems": [
"1. に をBOLT で取付"
],
"WorkPoints": [
"ﾃｰﾊﾟ側を下側にして挿入"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "95cN･m",
"WorkName": "ｽﾄｯﾊﾟｰ取付①",
"WorkItems": [
"1. BOLT にSPACER WASHER を通し に取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "95cN･m",
"WorkName": "ｼｬｯﾀｰ組立",
"WorkItems": [
"1. SHUTTER にBLOCK COLLAR GUIDE をBOLT で取付",
"2. 1完成品にCOLLAR GUIDE をBOLT で仮取付"
],
"WorkPoints": [
"仮取付で組立(穴位置は図の通り)",
"仮組立品を㉘治具に取付",
"全体を矢印方向に押し治具に当てﾚﾊﾞｰで固定する",
"次ﾍﾟｰｼ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰｼｬｯﾀｰｶﾞｲﾄﾞ面合わせ治具",
"Size": "",
"ToolOther": "FM-4868",
"WorkName": "ｼｬｯﾀｰ組立",
"WorkItems": [
"1. SHUTTER にBLOCK COLLAR GUIDE をBOLT で取付",
"2. 1完成品にCOLLAR GUIDE をBOLT で仮取付"
],
"WorkPoints": [
"仮取付で組立(穴位置は図の通り)",
"仮組立品を㉘治具に取付",
"GUIDE を治具のDﾋﾟﾝに当てつけ",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4868",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り治具に取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "95cN･m",
"WorkName": "ｼｬｯﾀｰ取付①",
"WorkItems": [
"2. に を挿入し､COLLAR BOLT で取付",
"◆1. のﾍﾞｱﾘﾝｸﾞ(8か所)にｸﾞﾘｰｽを塗布"
],
"WorkPoints": [
"指示箇所のﾍﾞｱﾘﾝｸﾞにｸﾞﾘｰｽを塗布"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"Insp... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ取付①",
"WorkItems": [
"2. に を挿入し､COLLAR BOLT で取付",
"◆1. のﾍﾞｱﾘﾝｸﾞ(8か所)にｸﾞﾘｰｽを塗布",
"3. ベアリングとガイドの当たりを調整し隙間が無いことを㉙にて4箇所確認すること"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞとｶﾞｲﾄﾞの当たり調整ｼｬｯﾀｰ動作時に各ﾍﾞｱﾘﾝｸﾞが回転する事",
"当てつけながら直角に取付",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ取付①",
"WorkItems": [],
"WorkPoints": [
"治具にて取付した基準側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾄｯﾊﾟｰ取付②",
"WorkItems": [
"▲1. BLOCK にSTOPPER を接着",
"▲2. 1完成品をBOLT WASHER で に取付"
],
"WorkPoints": [
"ﾃｰﾊﾟｰ側を挿入",
"STOPPER を挿入する前に接着剤を塗布",
"BOLT のﾎﾞﾙﾄ先端に接着剤を塗布",
"ｼｬｯﾀｰを矢印方向に押し､治具に当てつけ0.02㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "剥がれ無き事米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "接着剤ｽｰﾊﾟｰX",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾄｯﾊﾟｰ取付②",
"WorkItems": [
"▲1. BLOCK にSTOPPER を接着",
"▲2. 1完成品をBOLT WASHER で に取付"
],
"WorkPoints": [
"ﾃｰﾊﾟｰ側を挿入",
"STOPPER を挿入する前に接着剤を塗布",
"BOLT のﾎﾞﾙﾄ先端に接着剤を塗布",
"ｼｬｯﾀｰを矢印方向に押し､治具に当てつけ0.02㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "剥がれ無き事米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "接着剤ﾛｯｸﾀｲﾄ243",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｽﾄｯﾊﾟｰ取付②",
"WorkItems": [
"▲1. BLOCK にSTOPPER を接着",
"▲2. 1完成品をBOLT WASHER で に取付"
],
"WorkPoints": [
"ﾃｰﾊﾟｰ側を挿入",
"STOPPER を挿入する前に接着剤を塗布",
"飛び出した接着剤はふき取る事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｬｯﾀｰ調整治具",
"Size": "",
"ToolOther": "FM-2419",
"WorkName": "ｽﾄｯﾊﾟｰ取付②",
"WorkItems": [
"▲1. BLOCK にSTOPPER を接着",
"▲2. 1完成品をBOLT WASHER で に取付"
],
"WorkPoints": [
"ﾃｰﾊﾟｰ側を挿入",
"STOPPER を挿入する前に接着剤を塗布",
"飛び出した接着剤はふき取る事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2419",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに取付出来ている事",
"Method": "目視",
"RecordMethod": "DH7M-D019-024",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "ｽﾄｯﾊﾟｰ取付②",
"WorkItems": [
"▲1. BLOCK にSTOPPER を接着",
"▲2. 1完成品をBOLT WASHER で に取付"
],
"WorkPoints": [
"ﾃｰﾊﾟｰ側を挿入",
"STOPPER を挿入する前に接着剤を塗布",
"飛び出した接着剤はふき取る事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "DH7M-D019-024",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｼｬｯﾀｰ取付②",
"WorkItems": [
"3. GUIDE にWASHER を貼付し､BOLT WASHER で取付"
],
"WorkPoints": [
"GUIDE にWASHER を㉘で貼付"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ取付②",
"WorkItems": [
"◆1. とWASHER にｸﾞﾘｰｽを塗布",
"2. に をBOLT で取付し､SPRING を挿入",
"3. GUIDE にWASHER を貼付し､BOLT WASHER で取付"
],
"WorkPoints": [
"PINがGUIDE穴の中心になるよう調整",
"ｼｬｯﾀｰを可動させた場合にPINがGUIDEに接触しないよう取付位置を調整",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ取付②",
"WorkItems": [
"◆1. とWASHER にｸﾞﾘｰｽを塗布",
"2. に をBOLT で取付し､SPRING を挿入",
"3. GUIDE にWASHER を貼付し､BOLT WASHER で取付"
],
"WorkPoints": [
"PINがGUIDE穴の中心になるよう調整",
"ｼｬｯﾀｰを可動させた場合にPINがGUIDEに接触しないよう取付位置を調整",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾌﾞﾛｯｸ取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｶﾞｲﾄﾞ位置調整治具",
"Size": "",
"ToolOther": "FM-2178",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. にGUIDE をBOLT WASHER で取付"
],
"WorkPoints": [
"ﾁｪﾝｼﾞｬｰを治具にｾｯﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2178",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "DH7M-D019-024",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. にGUIDE をBOLT WASHER で取付"
],
"WorkPoints": [
"ﾁｪﾝｼﾞｬｰを治具にｾｯﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. にGUIDE をBOLT WASHER で取付"
],
"WorkPoints": [
"ﾁｪﾝｼﾞｬｰを治具にｾｯﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wor... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "DH7M-D019-024",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. にGUIDE をBOLT WASHER で取付",
"◆2. 1完成品にｸﾞﾘｰｽを塗布"
],
"WorkPoints": [
"治具にて調整し本締めの為､仮締め",
"ﾁｪﾝｼﾞｬｰを治具にｾｯﾄ",
"GUIDE を治具に当てつけ(矢印方向)て取付",
"締結後､ｼｯｸﾈｽｹﾞｰｼﾞ0.02㎜が通らないことを確認",
"j治具を抜いた時に... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ動作確認",
"WorkItems": [
"1. ｼｬｯﾀｰの動作確認実施"
],
"WorkPoints": [
"ｼｬｯﾀｰをﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞで押して開くときのｽﾄﾛｰｸ全域での最大荷重を測定⇒ 4N以下"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Word... | {
"QualityItem": "摺動確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "ｽﾄﾛｰｸ全域にて4N以下",
"Method": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"RecordMethod": "DH7M-D019-024",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6326",
"WorkName": "銘板貼付",
"WorkItems": [
"1. に㉗でLABEL LABEL を貼付",
"2. 1完成品に④を貼付"
],
"WorkPoints": [
"㉗のピン（３ヶ所）を シャッター側面にスキマ無く 当付けること",
"ｼｬｯﾀｰ面を傷つけないこと",
"貼付け方向に注意すること",
"貼付け後はｽｹｰﾙで寸法確認すること"
],
"Tolks": ... | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-6326",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付",
"WorkItems": [
"1. に㉗でLABEL LABEL を貼付",
"2. 1完成品に④を貼付",
"1. に㉗でLABEL LABEL を貼付",
"2. 1完成品に④を貼付"
],
"WorkPoints": [
"㉗のピン（３ヶ所）を シャッター側面にスキマ無く 当付けること",
"ｼｬｯﾀｰ面を傷つけないこと",
"貼付け方向に注意すること",
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"Size": "",
"ToolOther": "FM-2169",
"WorkName": "機能検査",
"WorkItems": [
"2. ﾉｽﾞﾙｾｯﾄ確認",
"1. ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ脱着確認"
],
"WorkPoints": [
"ｽﾑｰｽﾞにｾｯﾄできる事",
"着脱の際､引っかかりなく着脱できる事",
"ﾁｪﾝｼﾞｬｰを治具の上にｾｯﾄ(ﾚﾊﾞｰを押さない状態)",
"治具のﾚﾊﾞｰを押すと自重にて落下する事"
],
"To... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2169",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作する事",
"Method": "目視",
"RecordMethod": "DH7M-D019-024",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬ確認治具",
"Size": "",
"ToolOther": "FM-2411",
"WorkName": "機能検査",
"WorkItems": [
"2. ﾉｽﾞﾙｾｯﾄ確認",
"1. ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ脱着確認"
],
"WorkPoints": [
"ｽﾑｰｽﾞにｾｯﾄできる事",
"着脱の際､引っかかりなく着脱できる事",
"ﾁｪﾝｼﾞｬｰを治具の上にｾｯﾄ(ﾚﾊﾞｰを押さない状態)",
"治具のﾚﾊﾞｰを押すと自重にて落下する事"
],
"Tolks... | {
"QualityItem": "ｾｯﾄ確認",
"ToolManageNo": "FM-2411",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りｾｯﾄ出来る事",
"Method": "目視",
"RecordMethod": "DH7M-D019-024",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "駆動部調整検査治具乗せこみ前準備",
"WorkItems": [
"1. 駆動部の指示のﾎﾞﾙﾄをすべて緩める"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :治具活用前準備",
"ﾈｼﾞ緩め箇所",
"ﾈｼﾞ緩め箇所",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C41",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6626",
"WorkName": "駆動部調整検査治具乗せこみ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "切替ﾕﾆｯﾄ運搬台車(NPM-GH)",
"Size": "",
"ToolOther": "FM-6630",
"WorkName": "駆動部調整検査治具乗せこみ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6630",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "駆動部調整検査治具乗せこみ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WEPJ-G002-C41"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C41",
"Other": "重量物",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6626",
"WorkName": "駆動部側面調整",
"WorkItems": [
"1. ﾌﾞﾛｯｸの取付位置を合わせて､締結"
],
"WorkPoints": [
"ﾋﾟﾝとﾌﾞﾛｯｸの隙間確認(0.03㎜が通ら無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替ﾕﾆｯﾄ運搬台車(NPM-GH)",
"Size": "",
"ToolOther": "FM-6630",
"WorkName": "駆動部側面調整",
"WorkItems": [
"1. ﾌﾞﾛｯｸの取付位置を合わせて､締結"
],
"WorkPoints": [
"ﾋﾟﾝとﾌﾞﾛｯｸの隙間確認(0.03㎜が通ら無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTyp... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6630",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "駆動部側面調整",
"WorkItems": [
"1. ﾌﾞﾛｯｸの取付位置を合わせて､締結"
],
"WorkPoints": [
"ﾋﾟﾝとﾌﾞﾛｯｸの隙間確認(0.03㎜が通ら無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C41",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "駆動部側面調整",
"WorkItems": [
"1. ﾌﾞﾛｯｸの取付位置を合わせて､締結"
],
"WorkPoints": [
"ﾋﾟﾝとﾌﾞﾛｯｸの隙間確認(0.03㎜が通ら無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "支持部調整検査治具乗せこみ前準備",
"WorkItems": [
"1. 支持部の指示のﾎﾞﾙﾄをすべて緩める"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :治具活用前準備",
"ﾈｼﾞ緩め箇所",
"ﾈｼﾞ緩め箇所",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C43",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6626",
"WorkName": "支持部調整検査治具乗せこみ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替ﾕﾆｯﾄ運搬台車(NPM-GH)",
"Size": "",
"ToolOther": "FM-6630",
"WorkName": "支持部調整検査治具乗せこみ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6630",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "支持部調整検査治具乗せこみ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WEPJ-G002-C43"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C43",
"Other": "重量物",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6626",
"WorkName": "支持部側面調整",
"WorkItems": [
"1. ﾌﾞﾛｯｸの取付位置を合わせて､締結"
],
"WorkPoints": [
"ﾋﾟﾝとﾌﾞﾛｯｸの隙間確認(0.03㎜が通ら無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes":... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替ﾕﾆｯﾄ運搬台車(NPM-GH)",
"Size": "",
"ToolOther": "FM-6630",
"WorkName": "支持部側面調整",
"WorkItems": [
"1. ﾌﾞﾛｯｸの取付位置を合わせて､締結"
],
"WorkPoints": [
"ﾋﾟﾝとﾌﾞﾛｯｸの隙間確認(0.03㎜が通ら無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTy... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6630",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "支持部側面調整",
"WorkItems": [
"1. ﾌﾞﾛｯｸの取付位置を合わせて､締結"
],
"WorkPoints": [
"ﾋﾟﾝとﾌﾞﾛｯｸの隙間確認(0.03㎜が通ら無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C43",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "支持部側面調整",
"WorkItems": [
"1. ﾌﾞﾛｯｸの取付位置を合わせて､締結"
],
"WorkPoints": [
"ﾋﾟﾝとﾌﾞﾛｯｸの隙間確認(0.03㎜が通ら無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6626",
"WorkName": "調整検査治具取付",
"WorkItems": [
"1. ㉘の治具を取付"
],
"WorkPoints": [
"決して押し付けないように接触させる程度",
"平行ﾋﾟﾝにてX方向に正確に位置決めされるようにｾｯﾄし､ﾉﾌﾞで固定して使用する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Work... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替ﾕﾆｯﾄ運搬台車(NPM-GH)",
"Size": "",
"ToolOther": "FM-6630",
"WorkName": "調整検査治具取付",
"WorkItems": [
"1. ㉘の治具を取付"
],
"WorkPoints": [
"決して押し付けないように接触させる程度",
"平行ﾋﾟﾝにてX方向に正確に位置決めされるようにｾｯﾄし､ﾉﾌﾞで固定して使用する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6630",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ(34連専用部)",
"Size": "",
"ToolOther": "FM-6668",
"WorkName": "調整検査治具取付",
"WorkItems": [
"1. ㉘の治具を取付"
],
"WorkPoints": [
"決して押し付けないように接触させる程度",
"平行ﾋﾟﾝにてX方向に正確に位置決めされるようにｾｯﾄし､ﾉﾌﾞで固定して使用する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6668",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6626",
"WorkName": "駆動部支持部調整と検査",
"WorkItems": [
"1. 駆動部の樹脂ｶﾞｲﾄﾞ部の幅を治具に沿わせて位置決め調整",
"2. 支持部の樹脂ｶﾞｲﾄﾞ部の幅を治具に沿わせて位置決め調整"
],
"WorkPoints": [
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"調整は右... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替ﾕﾆｯﾄ運搬台車(NPM-GH)",
"Size": "",
"ToolOther": "FM-6630",
"WorkName": "駆動部支持部調整と検査",
"WorkItems": [
"1. 駆動部の樹脂ｶﾞｲﾄﾞ部の幅を治具に沿わせて位置決め調整",
"2. 支持部の樹脂ｶﾞｲﾄﾞ部の幅を治具に沿わせて位置決め調整"
],
"WorkPoints": [
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6630",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ(34連専用部)",
"Size": "",
"ToolOther": "FM-6668",
"WorkName": "駆動部支持部調整と検査",
"WorkItems": [
"1. 駆動部の樹脂ｶﾞｲﾄﾞ部の幅を治具に沿わせて位置決め調整",
"2. 支持部の樹脂ｶﾞｲﾄﾞ部の幅を治具に沿わせて位置決め調整"
],
"WorkPoints": [
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6668",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "駆動部支持部調整と検査",
"WorkItems": [
"1. 駆動部の樹脂ｶﾞｲﾄﾞ部の幅を治具に沿わせて位置決め調整",
"2. 支持部の樹脂ｶﾞｲﾄﾞ部の幅を治具に沿わせて位置決め調整"
],
"WorkPoints": [
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"調整は右図の3か所が... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C41",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "駆動部支持部調整と検査",
"WorkItems": [
"1. 駆動部の樹脂ｶﾞｲﾄﾞ部の幅を治具に沿わせて位置決め調整",
"2. 支持部の樹脂ｶﾞｲﾄﾞ部の幅を治具に沿わせて位置決め調整"
],
"WorkPoints": [
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"調整は右図の3か所が... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C43",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "駆動部支持部調整と検査",
"WorkItems": [
"1. 駆動部の樹脂ｶﾞｲﾄﾞ部の幅を治具に沿わせて位置決め調整",
"2. 支持部の樹脂ｶﾞｲﾄﾞ部の幅を治具に沿わせて位置決め調整"
],
"WorkPoints": [
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"調整は右図の3か所が... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "駆動部支持部調整と検査",
"WorkItems": [
"1. 駆動部の樹脂ｶﾞｲﾄﾞ部の幅を治具に沿わせて位置決め調整"
],
"WorkPoints": [
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 194... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6626",
"WorkName": "駆動部支持部取り外し",
"WorkItems": [
"1. から治具㉘の調整用ブロック（青色）を取り外す",
"2. 駆動部と支持部を治具㉖㉗から取り外す"
],
"WorkPoints": [
"駆動部と支持部を取り外し時に接触するため",
"駆動部",
"支持部"
],
"Tolks": [],
"InspectionNo": "",
"Inspect... | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-6626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替ﾕﾆｯﾄ運搬台車(NPM-GH)",
"Size": "",
"ToolOther": "FM-6630",
"WorkName": "駆動部支持部取り外し",
"WorkItems": [
"1. から治具㉘の調整用ブロック（青色）を取り外す",
"2. 駆動部と支持部を治具㉖㉗から取り外す"
],
"WorkPoints": [
"駆動部と支持部を取り外し時に接触するため",
"駆動部",
"支持部"
],
"Tolks": [],
"InspectionNo": "",
"In... | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-6630",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ(34連専用部)",
"Size": "",
"ToolOther": "FM-6668",
"WorkName": "駆動部支持部取り外し",
"WorkItems": [
"1. から治具㉘の調整用ブロック（青色）を取り外す"
],
"WorkPoints": [
"駆動部と支持部を取り外し時に接触するため"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words":... | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-6668",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "逆流れﾌﾚｰﾑｷｯﾄL組立①",
"WorkItems": [
"1. FRAME にSUPPORT NUT NUT NUT NUT NUT CABLE-SUPPORT を取付け",
"2. 1.完成品にCAP CAP を取付"
],
"WorkPoints": [
"上面",
"外面",
"左面",
"内面",
"内面",
"右面",
"外面",
"左面"... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "150cN･m",
"WorkName": "逆流れﾌﾚｰﾑｷｯﾄL組立②",
"WorkItems": [
"2. 1.完成品にCAP を取付け",
"1. にBRACKET BRACKET BRACKET BRACKET をWASHER BOLT で取付け"
],
"WorkPoints": [
"ｾｯﾄｽｸﾘｭｰ締め付け",
"ﾌﾞﾗｹｯﾄ固定後導通確保の為ｾｯﾄｽｸﾘｭｰを締め付ける",
"内面",
"右面",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "逆流れﾌﾚｰﾑｷｯﾄL組立②",
"WorkItems": [
"2. 1.完成品にCAP を取付け",
"1. にBRACKET BRACKET BRACKET BRACKET をWASHER BOLT で取付け"
],
"WorkPoints": [
"ｾｯﾄｽｸﾘｭｰ締め付け",
"ﾌﾞﾗｹｯﾄ固定後導通確保の為ｾｯﾄｽｸﾘｭｰを締め付ける",
"内面",
"右面",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "逆流れﾌﾚｰﾑｷｯﾄL組立③",
"WorkItems": [
"1. FRAME にSUPPORT NUT NUT NUT NUT CABLE-SUPPORT を取付け"
],
"WorkPoints": [
"上面",
"外面",
"左面",
"内面",
"･は止めﾈｼﾞの方向を示す",
"内面",
"SUPPORT はNUT NUT NUT NUT とｾｯﾄで使用",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "150cN･m",
"WorkName": "逆流れﾌﾚｰﾑｷｯﾄL組立④",
"WorkItems": [
"2. 1.完成品にCAP を取付け",
"1. にBRACKET BRACKET BRACKET をWASHER BOLT で取付け"
],
"WorkPoints": [
"ｾｯﾄｽｸﾘｭｰ締め付け",
"ﾌﾞﾗｹｯﾄ固定後導通確保の為ｾｯﾄｽｸﾘｭｰを締め付ける",
"内面",
"内面",
"右面... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "逆流れﾌﾚｰﾑｷｯﾄL組立④",
"WorkItems": [
"2. 1.完成品にCAP を取付け",
"1. にBRACKET BRACKET BRACKET をWASHER BOLT で取付け"
],
"WorkPoints": [
"ｾｯﾄｽｸﾘｭｰ締め付け",
"ﾌﾞﾗｹｯﾄ固定後導通確保の為ｾｯﾄｽｸﾘｭｰを締め付ける",
"内面",
"内面",
"右面",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "逆流れﾌﾚｰﾑｷｯﾄL組立⑤",
"WorkItems": [
"1. FRAME にSUPPORT NUT NUT を取付け"
],
"WorkPoints": [
"上面",
"外面",
"下面",
"内面",
"･は止めﾈｼﾞの方向を示す",
"内面",
"SUPPORT はNUT NUT とｾｯﾄで使用",
"内面",
"下面",
"外面"... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "150cN･m",
"WorkName": "逆流れﾌﾚｰﾑｷｯﾄL組立⑥",
"WorkItems": [
"1. の下側にBRACKET をWASHER BOLT で取付け"
],
"WorkPoints": [
"下面",
"外面",
"上面",
"後面",
" とBRACKET の端面を合わせる",
"内面",
"ﾌﾞﾗｹｯﾄ固定後導通確保の為ｾｯﾄｽｸﾘｭｰを締め付ける",
"ｾｯ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "逆流れﾌﾚｰﾑｷｯﾄL組立⑥",
"WorkItems": [
"1. の下側にBRACKET をWASHER BOLT で取付け"
],
"WorkPoints": [
"下面",
"外面",
"上面",
"後面",
" とBRACKET の端面を合わせる",
"内面",
"ﾌﾞﾗｹｯﾄ固定後導通確保の為ｾｯﾄｽｸﾘｭｰを締め付ける",
"ｾｯﾄｽｸﾘ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "逆流れﾌﾚｰﾑｷｯﾄL組立⑦",
"WorkItems": [
"1. FRAME にSUPPORT NUT NUT CABLE-SUPPORT を取付け"
],
"WorkPoints": [
"外面",
"下面",
"内面",
"･は止めﾈｼﾞの方向を示す",
"内面",
"SUPPORT はNUT NUT とｾｯﾄで使用",
"内面",
"下面",
"... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "150cN･m",
"WorkName": "逆流れﾌﾚｰﾑｷｯﾄL組立⑧",
"WorkItems": [
"1. にBRACKET BRACKET をWASHER BOLT で取付け"
],
"WorkPoints": [
"下面",
"BRACKET BRACKET と の端面を合わせる",
"BRACKET は下面､BRACKET は上面に取付け",
"上面",
"ｾｯﾄｽｸﾘｭｰ締め付け",
"ｾｯﾄ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "逆流れﾌﾚｰﾑｷｯﾄL組立⑨",
"WorkItems": [
"1. FRAME にSUPPORT NUT NUT CABLE-SUPPORT を取付け"
],
"WorkPoints": [
"外面",
"下面",
"内面",
"･は止めﾈｼﾞの方向を示す",
"SUPPORT はNUT NUT とｾｯﾄで使用",
"内面",
"下面",
"外面",
"... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "150cN･m",
"WorkName": "逆流れﾌﾚｰﾑｷｯﾄL組立⑩",
"WorkItems": [
"1. にBRACKET BRACKET をWASHER BOLT で取付け"
],
"WorkPoints": [
"下面",
"BRACKET BRACKET と の端面を合わせる",
"BRACKET は下面､BRACKET は上面に取付け",
"上面",
"ｾｯﾄｽｸﾘｭｰ締め付け",
"ｾｯﾄ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "逆流れﾌﾚｰﾑｷｯﾄL組立⑪",
"WorkItems": [
"1. をWASHER BOLT で取付け"
],
"WorkPoints": [
" と の端面を合わせる",
" と の端面を合わせる",
"㉗定盤側に外面を合わせて組立てる",
"内面側",
"ﾌﾞﾗｹｯﾄ固定後導通確保の為ｾｯﾄｽｸﾘｭｰを締め付ける",
"ｾｯﾄｽｸﾘｭｰ締め付け",
"ｾｯﾄｽ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "150cN･m",
"WorkName": "逆流れﾌﾚｰﾑｷｯﾄL組立⑪",
"WorkItems": [
"1. をWASHER BOLT で取付け"
],
"WorkPoints": [
" と の端面を合わせる",
" と の端面を合わせる",
"㉗定盤側に外面を合わせて組立てる",
"内面側",
"ﾌﾞﾗｹｯﾄ固定後導通確保の為ｾｯﾄｽｸﾘｭｰを締め付ける",
"ｾｯﾄｽｸﾘｭｰ締め付け",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.5N･m",
"WorkName": "逆流れﾌﾚｰﾑｷｯﾄL組立⑪",
"WorkItems": [
"1. をWASHER BOLT で取付け"
],
"WorkPoints": [
" と の端面を合わせる",
" と の端面を合わせる",
"㉗定盤側に外面を合わせて組立てる",
"内面側",
"ﾌﾞﾗｹｯﾄ固定後導通確保の為ｾｯﾄｽｸﾘｭｰを締め付ける",
"ｾｯﾄｽｸﾘｭｰ締め付け",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "PLATEの砥石がけ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "-",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "-",
"Method": "-",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "治具",
"Size": "FM-2254",
"ToolOther": "FM-2254",
"WorkName": "ﾋﾟﾝ圧入1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. にPIN PIN を圧入",
"PIN ",
"PIN ",
"PIN のﾋﾟﾝ出代:5mm",
"PI... | {
"QualityItem": "-",
"ToolManageNo": "FM-2254",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾋﾟﾝ圧入ｼﾞｸﾞ",
"Method": "-",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.