Datasets:
ayuzawa
/
ManageProcess19

Dataset card Data Studio Files
xet
Community
1
input
stringclasses
1 value
instruction
stringlengths
222
1.92k
output
stringlengths
193
312
category
stringclasses
1 value
index
stringclasses
1 value
fileName
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "制御BOX引き回し", "WorkItems": [ "1. 上からの配線を引き回し固定する", "2. 制御BOX内を引き回し･接続する" ], "WorkPoints": [ "PGK601/2LANCN2K6031S301RHDR", "CN101K305配管", "ｸﾞﾛﾒｯﾄから出す", "LAN", "PGK601", "PGK602", "CN2K603", "1S301R", "HDR" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "検査表①:4.接続確認" ] }
{ "QualityItem": "結束確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り結束出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "制御BOX引き回し", "WorkItems": [ "1. 上からの配線を引き回し固定する", "2. 制御BOX内を引き回し･接続する" ], "WorkPoints": [ "PGK601/2LANCN2K6031S301RHDR", "CN101K305配管", "ｸﾞﾛﾒｯﾄから出す", "LAN", "PGK601", "PGK602", "CN2K603", "1S301R", "HDR" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "検査表①:4.接続確認", "WEWD-F013-051" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "WEWD-F013-051", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "制御BOX内整線", "WorkItems": [ "1. 配線にNOISE-FILTER NOISE-FILTER を取付け後､配線を固定する" ], "WorkPoints": [ "RS232Cｹｰﾌﾞﾙのみ", "LANｹｰﾌﾞﾙのみ" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "ｲﾝｼｭﾛｯｸ(150mm)", "ｲﾝｼｭﾛｯｸ(150mm)", "ｲﾝｼｭﾛｯｸ(150mm)", "ｲﾝｼｭﾛｯｸ(150mm)" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "制御BOX内整線", "WorkItems": [ "1. 配線にNOISE-FILTER NOISE-FILTER を取付け後､配線を固定する" ], "WorkPoints": [ "RS232Cｹｰﾌﾞﾙのみ", "LANｹｰﾌﾞﾙのみ" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "ｲﾝｼｭﾛｯｸ(150mm)", "ｲﾝｼｭﾛｯｸ(150mm)", "ｲﾝｼｭﾛｯｸ(150mm)", "ｲﾝｼｭﾛｯｸ(150mm)" ] }
{ "QualityItem": "結束確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り結束出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌｨｰﾀﾞｰ基板側引き回し・接続", "WorkItems": [ "1. 配線を引き回し･接続する", "■★2. FG線をSCREW で固定する" ], "WorkPoints": [ "CN101K305", "CN100K305", "1B011P配管", "CN100K305CN101K305", "FG2K305", "FGK305" ], "Tolks": [ "締付ﾄﾙｸ 180cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "検査表SCREW :4.接続確認", "検査表SCREW :3.締め付けﾄﾙｸの確認" ] }
{ "QualityItem": "結束確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り結束出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "180cN･m", "WorkName": "ﾌｨｰﾀﾞｰ基板側引き回し・接続", "WorkItems": [ "1. 配線を引き回し･接続する", "■★2. FG線をSCREW で固定する" ], "WorkPoints": [ "CN100K305CN101K305", "FG2K305", "FGK305" ], "Tolks": [ "締付ﾄﾙｸ 180cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "■安全作業", "★静電対策作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "180cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "流量ｽｲｯﾁ側引き回し・接続", "WorkItems": [ "1. 配線､配管を引き回し･接続する" ], "WorkPoints": [ "1B011P/R", "配管" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "検査表①:4.接続確認" ] }
{ "QualityItem": "結束確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り結束出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "流量ｽｲｯﾁ側引き回し・接続", "WorkItems": [ "1. 配線､配管を引き回し･接続する" ], "WorkPoints": [ "1B011P/R", "配管" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "検査表①:4.接続確認", "WEWD-F013-051" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "WEWD-F013-051", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾍﾞｱﾘﾝｸﾞDﾋﾟﾝ圧入治具", "Size": "", "ToolOther": "FM-2250", "WorkName": "ﾍﾞｱﾘﾝｸﾞ前組み", "WorkItems": [ "1. BEARING にPIN を圧入する" ], "WorkPoints": [ "治具にBEARING をｾｯﾄする", "ﾃｰﾊﾟｰ側を上にして圧入", "治具の上側を下側のﾋﾟﾝにはめ込む", "PIN を挿入し圧入する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-2250", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "油砥石", "Size": "細目", "ToolOther": "", "WorkName": "ﾌﾞﾛｯｸ前組み", "WorkItems": [ "2. 1完成品にPIN を圧入する", "1. BLOCK に砥石をかける" ], "WorkPoints": [ "面取りが大きい方を上にする" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "位置決めﾌﾞﾛｯｸﾋﾟﾝ打ち込み治具", "Size": "", "ToolOther": "FM-2253", "WorkName": "ﾌﾞﾛｯｸ前組み", "WorkItems": [ "2. 1完成品にPIN を圧入する", "1. BLOCK に砥石をかける" ], "WorkPoints": [ "面取りが大きい方を上にする" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-2253", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "接着剤ﾛｯｸﾀｲﾄ243", "WorkName": "ﾋﾟﾝ圧入", "WorkItems": [ "▲1. BLOCK に接着剤を塗布する", "2. 1完成品をPIN に圧入する" ], "WorkPoints": [ "ﾃｰﾊﾟｰ側に塗布する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "接着剤塗布 米粒:1", "▲特殊作業" ] }
{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:1", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾊﾞﾈｶﾞｲﾄﾞ､Dﾋﾟﾝ圧入治具", "Size": "", "ToolOther": "FM-2252", "WorkName": "ﾋﾟﾝ圧入", "WorkItems": [ "▲1. BLOCK に接着剤を塗布する", "2. 1完成品をPIN に圧入する" ], "WorkPoints": [ "ﾃｰﾊﾟｰ側に塗布する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "接着剤塗布 米粒:1", "▲特殊作業" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-2252", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "接着剤ｽｰﾊﾟｰX(AX-039)", "WorkName": "ｽﾄｯﾊﾟｰ接着", "WorkItems": [ "▲1. BLOCK に接着剤を塗布する", "2. 1完成品にSTOPPER を挿入する" ], "WorkPoints": [ "㉖で清掃後塗布する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "接着剤塗布 ｺﾞﾏ粒:2", "▲特殊作業" ] }
{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布ｺﾞﾏ粒:2", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍﾞｰｽ準備", "WorkItems": [ "1. BASE の指示部に油砥石をかける" ], "WorkPoints": [ "指示部にﾊﾞﾘ･打痕無き事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ﾊﾞﾘ､打痕､傷等が無い事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "1.27㎜", "ToolOther": "35cN･m", "WorkName": "ﾍﾞｰｽ組立_止めねじ取付け", "WorkItems": [ "1. にSCREW を取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 35cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "35cN・m", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾍﾞｰｽ組立_ﾋﾟﾝ圧入", "WorkItems": [ "1. にPIN を圧入する" ], "WorkPoints": [ "PIN出代:1.5㎜", "圧入方向" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "出代確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍﾞｰｽ組立_ﾍﾞｱﾘﾝｸﾞ圧入", "WorkItems": [ "1. に SPACER を取付ける" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "95cN･m", "WorkName": "ﾍﾞｰｽ組立_ﾎﾙﾀﾞｰ取付け", "WorkItems": [ "1. にHOLDER を挿入しBOLT で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ﾍﾞｰｽ組立_底面ﾍﾞｱﾘﾝｸﾞ取付け", "WorkItems": [ "1. にBEARING SPACER をBOLT で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ﾍﾞｰｽ組立_ﾌﾞﾛｯｸ取付け", "WorkItems": [ "1. に を挿入しBOLT で取付ける" ], "WorkPoints": [ "ﾃｰﾊﾟｰ側を下にして挿入する" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "95cN･m", "WorkName": "ﾍﾞｰｽ組立_ｽﾍﾟｰｻｰ取付け", "WorkItems": [ "1. にWASHER SPACER をBOLT で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍﾞｰｽ組立_ｸﾞﾘｰｽ塗布", "WorkItems": [ "◆1. のﾍﾞｱﾘﾝｸﾞにｸﾞﾘｰｽを塗布する" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:各1", "ｸﾞﾘｰｽ塗布 米粒:各2" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:各1・2", "Method": "目視", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "ｶﾞｲﾄﾞ前組み", "WorkItems": [ "1. にGUIDE をBOLT で取付ける" ], "WorkPoints": [ "定盤に当付けて取付けの事" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "", "ToolOther": "", "WorkName": "ｼｬｯﾀｰ前組み", "WorkItems": [ "2. 1完成品を定盤上で仮締結する", "1. SHUTTER にCOLLAR GUIDE BLOCK をBOLT で仮取付けする" ], "WorkPoints": [ "隙間無い事", "面を合わせる事", "SHUTTER COLLAR GUIDE BLOCK を定盤に当付けて締結の事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A052597-017にて本締め" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｼｬｯﾀｰ前組み", "WorkItems": [ "2. 1完成品を定盤上で仮締結する", "1. SHUTTER にCOLLAR GUIDE BLOCK をBOLT で仮取付けする" ], "WorkPoints": [ "隙間無い事", "面を合わせる事", "SHUTTER COLLAR GUIDE BLOCK を定盤に当付けて締結の事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A052597-017にて本締め" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｼｬｯﾀｰ取付け1", "WorkItems": [ "1. に を取付け､ COLLAR をBOLT で仮取付けする" ], "WorkPoints": [ "仮止め:SD-A052597-017にて本締め" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A051321-016にて本締め" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "95cN･m", "WorkName": "ｼｬｯﾀｰ取付け2", "WorkItems": [], "WorkPoints": [ "４箇所すべて㉙が通ら無い事" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｼｬｯﾀｰ取付け2", "WorkItems": [ "3. ﾍﾞｱﾘﾝｸﾞとｶﾞｲﾄﾞに隙間が無い事を確認する", "1. を定盤上で仮締結する", "2. 1完成品のｼｬｯﾀｰ開閉時に､4つのﾍﾞｱﾘﾝｸﾞが回転する事を確認し本締結する" ], "WorkPoints": [ "面を合わせる事", "ｶﾞｲﾄﾞを定盤に当付けて締結の事", "４箇所すべて㉙が通ら無い事" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "回転確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り回転出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.02㎜", "ToolOther": "", "WorkName": "ｼｬｯﾀｰ取付け2", "WorkItems": [], "WorkPoints": [ "４箇所すべて㉙が通ら無い事" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.02㎜が通ら無い事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "接着剤ﾛｯｸﾀｲﾄ243", "WorkName": "ｽﾄｯﾊﾟｰ取付け", "WorkItems": [ "▲1. BOLT に接着剤を塗布する", "2. に を1完成品とWASHER で取付ける" ], "WorkPoints": [ "ﾎﾞﾙﾄの先端に塗布する" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "接着剤塗布 米粒:1", "検査表 :3.ｼｬｯﾀｰ位置調整", "▲特殊作業" ] }
{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:1", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ｽﾄｯﾊﾟｰ取付け", "WorkItems": [ "▲1. BOLT に接着剤を塗布する", "2. に を1完成品とWASHER で取付ける" ], "WorkPoints": [ "ﾎﾞﾙﾄの先端に塗布する" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "接着剤塗布 米粒:1", "検査表 :3.ｼｬｯﾀｰ位置調整", "▲特殊作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｼｬｯﾀｰ調整治具", "Size": "", "ToolOther": "FM-2419", "WorkName": "ｽﾄｯﾊﾟｰ取付け", "WorkItems": [ "▲1. BOLT に接着剤を塗布する", "2. に を1完成品とWASHER で取付ける" ], "WorkPoints": [ "ﾎﾞﾙﾄの先端に塗布する" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "接着剤塗布 米粒:1", "検査表 :3.ｼｬｯﾀｰ位置調整", "▲特殊作業", "WETE-G002-C11" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-2419", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "WETE-G002-C11", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｽﾌﾟﾘﾝｸﾞ取付け", "WorkItems": [ "◆1. のﾋﾟﾝとWASHER にｸﾞﾘｰｽを塗布する", "2. にSPRING を挿入し､GUIDE にWASHER を貼付けBOLT WASHER で取付ける" ], "WorkPoints": [ "ﾋﾟﾝ全体に塗布する", "ﾍﾞｰｽに対して平行､ﾋﾟﾝがｶﾞｲﾄﾞ穴の中心になるよう取付けの事", "ｼｬｯﾀｰを開閉させｶﾞｲﾄﾞとﾋﾟﾝの干渉が無い事", "表裏に塗布する" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:各1", "ｸﾞﾘｰｽ塗布 米粒:2" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:2・ｺﾞﾏ粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ｽﾌﾟﾘﾝｸﾞ取付け", "WorkItems": [ "◆1. のﾋﾟﾝとWASHER にｸﾞﾘｰｽを塗布する", "2. にSPRING を挿入し､GUIDE にWASHER を貼付けBOLT WASHER で取付ける" ], "WorkPoints": [ "ﾍﾞｰｽに対して平行､ﾋﾟﾝがｶﾞｲﾄﾞ穴の中心になるよう取付けの事", "ｼｬｯﾀｰを開閉させｶﾞｲﾄﾞとﾋﾟﾝの干渉が無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:2", "◆作業者安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "ﾌﾞﾛｯｸ取付け", "WorkItems": [ "1. にBLOCK BLOCK をBOLT で取付ける" ], "WorkPoints": [ "BLOCK BLOCK をﾋﾟﾝに挿入する" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "ｽﾍﾟｰｻｰ・ﾄﾞｸﾞ取付け", "WorkItems": [ "1. にSPACER をBOLT で取付ける", "2. 1完成品にDOG をBOLT WASHER で取付ける" ], "WorkPoints": [ "㉙を矢印方向に当付ける" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m", "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ｽﾍﾟｰｻｰ・ﾄﾞｸﾞ取付け", "WorkItems": [ "1. にSPACER をBOLT で取付ける", "2. 1完成品にDOG をBOLT WASHER で取付ける" ], "WorkPoints": [ "㉙を矢印方向に当付ける" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m", "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾁｪﾝｼﾞｬｰﾄﾞｸﾞ_ﾌﾞﾛｯｸ_ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(FC16)", "Size": "", "ToolOther": "FM-6587", "WorkName": "ｽﾍﾟｰｻｰ・ﾄﾞｸﾞ取付け", "WorkItems": [ "1. にSPACER をBOLT で取付ける", "2. 1完成品にDOG をBOLT WASHER で取付ける" ], "WorkPoints": [ "㉙を矢印方向に当付ける" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m", "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-6587", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "T10", "ToolOther": "95cN･m", "WorkName": "識別用ﾌﾞﾛｯｸ取付け", "WorkItems": [ "1. にBLOCK をBOLT WASHER で取付ける" ], "WorkPoints": [ "㉘を矢印方向に当付けておく", "㉘を矢印方向に当付け取付ける" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾁｪﾝｼﾞｬｰﾄﾞｸﾞ_ﾌﾞﾛｯｸ_ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(FC16)", "Size": "", "ToolOther": "FM-6587", "WorkName": "識別用ﾌﾞﾛｯｸ取付け", "WorkItems": [ "1. にBLOCK をBOLT WASHER で取付ける" ], "WorkPoints": [ "㉘を矢印方向に当付けておく", "㉘を矢印方向に当付け取付ける" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-6587", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰﾁｪｯｶｰ機構部", "Size": "", "ToolOther": "FM-6553", "WorkName": "脱着・ｼｬｯﾀｰ動作確認", "WorkItems": [ "1. の脱着確認をする", "2. のｼｬｯﾀｰの動作確認をする" ], "WorkPoints": [ "引っ掛かり無き事", "開くときの最大荷重をｽﾄﾛｰｸ全域で測定する", "ﾚﾊﾞｰを押す" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "WETE-G002-C11" ] }
{ "QualityItem": "脱着確認", "ToolManageNo": "FM-6553", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "引っ掛かりが無い事", "Method": "目視", "RecordMethod": "WETE-G002-C11", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ", "Size": "", "ToolOther": "", "WorkName": "脱着・ｼｬｯﾀｰ動作確認", "WorkItems": [], "WorkPoints": [ "規格値:4.2N以下", "自重落下する事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :1.ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ脱着確認", "検査表 :2.ｼｬｯﾀｰ動作確認", "WETE-G002-C11" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "-", "ToolCycle": "1回/1年", "ToolRecord": "校正成績書", "StdVal": "4.2N以下", "Method": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ", "RecordMethod": "WETE-G002-C11", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾉｽﾞﾙｾｯﾄ確認", "WorkItems": [ "1. ﾉｽﾞﾙのｾｯﾄ確認をする" ], "WorkPoints": [ "引っ掛かりなくｽﾑｰｽﾞである事", "64ヵ所すべて確認する", "ｼｬｯﾀｰを閉じた状態で､ﾉｽﾞﾙが抜け無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :4.ﾉｽﾞﾙｾｯﾄ確認", "WETE-G002-C11" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "WETE-G002-C11", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "銘板貼付け", "WorkItems": [ "1. にLABEL LABEL LABEL を貼付ける" ], "WorkPoints": [ "1㎜", "25㎜", "1.5㎜", "40㎜", "㉘を使用し貼付ける", "28㎜", "1㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :5.ﾗﾍﾞﾙ貼付確認" ] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾁｪﾝｼﾞｬｰﾄﾞｸﾞ_ﾌﾞﾛｯｸ_ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(FC16)", "Size": "", "ToolOther": "FM-6587", "WorkName": "銘板貼付け", "WorkItems": [ "1. にLABEL LABEL LABEL を貼付ける" ], "WorkPoints": [ "1㎜", "25㎜", "1.5㎜", "40㎜", "㉘を使用し貼付ける", "28㎜", "1㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :5.ﾗﾍﾞﾙ貼付確認" ] }
{ "QualityItem": "貼付確認", "ToolManageNo": "FM-6587", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り貼付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾍﾞｱﾘﾝｸﾞDﾋﾟﾝ圧入治具", "Size": "", "ToolOther": "FM-2250", "WorkName": "ﾍﾞｱﾘﾝｸﾞ前組み", "WorkItems": [ "1. に を圧入する" ], "WorkPoints": [ "治具に をｾｯﾄする", "ﾃｰﾊﾟｰ側を上にして圧入", "治具の上側を下側のﾋﾟﾝにはめ込む", " を挿入し圧入する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-2250", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "油砥石", "Size": "細目", "ToolOther": "", "WorkName": "ﾌﾞﾛｯｸ前組み", "WorkItems": [ "2. 1完成品にPIN を圧入する", "1. BLOCK に砥石をかける" ], "WorkPoints": [ "面取りが大きい方を上にする" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "位置決めﾌﾞﾛｯｸﾋﾟﾝ打ち込み治具", "Size": "", "ToolOther": "FM-2253", "WorkName": "ﾌﾞﾛｯｸ前組み", "WorkItems": [ "2. 1完成品にPIN を圧入する", "1. BLOCK に砥石をかける" ], "WorkPoints": [ "面取りが大きい方を上にする" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを2個製作" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-2253", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾋﾟﾝ圧入", "WorkItems": [ "▲1. PIN に接着剤を塗布する", "2. 1完成品をBLOCK に圧入する" ], "WorkPoints": [ "ﾃｰﾊﾟｰ側に塗布する", "治具にBLOCK を挿入する", "治具にPIN 完成品をを挿入する", "圧入する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "接着剤塗布 米粒:1" ] }
{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:1", "Method": "目視", "RecordMethod": "-", "Other": "ﾛｯｸﾀｲﾄ243", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾊﾞﾈｶﾞｲﾄﾞ､Dﾋﾟﾝ圧入治具", "Size": "", "ToolOther": "FM-2252", "WorkName": "ﾋﾟﾝ圧入", "WorkItems": [], "WorkPoints": [ "治具にPIN 完成品をを挿入する", "圧入する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "接着剤塗布 米粒:1", "▲特殊作業" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-2252", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｽﾄｯﾊﾟｰ接着", "WorkItems": [ "▲1. BLOCK に接着剤を塗布する", "2. 1完成品にSTOPPER を挿入する" ], "WorkPoints": [ "ﾃｰﾊﾟｰ側を挿入する", "㉖で清掃後塗布する", "はみ出した接着剤を拭き取る" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "接着剤塗布 ｺﾞﾏ粒:2" ] }
{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布ｺﾞﾏ粒:2", "Method": "目視", "RecordMethod": "-", "Other": "ｽｰﾊﾟｰX(AX-039)", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍﾞｰｽ準備", "WorkItems": [ "1. の指示部に油砥石をかける" ], "WorkPoints": [ "指示部にﾊﾞﾘ･打痕無き事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ﾊﾞﾘ､打痕､傷等が無い事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "1.27㎜", "ToolOther": "35cN･m", "WorkName": "ﾍﾞｰｽ組立_止めねじ取付け", "WorkItems": [ "1. に を取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 35cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "35cN・m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "Dﾋﾟﾝ圧入治具(出代2.0)", "Size": "", "ToolOther": "FM-6666", "WorkName": "ﾍﾞｰｽ組立_ﾋﾟﾝ圧入", "WorkItems": [ "1. に㉖を搭載する", "3. 残りの3列も同様に を圧入する" ], "WorkPoints": [ "圧入したﾋﾟﾝにｼﾞｸﾞを挿入後､ﾋﾟﾝを圧入する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "出代確認", "ToolManageNo": "FM-6666", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り圧入出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍﾞｰｽ組立_ｼｰﾄ貼付け", "WorkItems": [ "1. にSHEET を貼付ける" ], "WorkPoints": [ "剥がれ無き事", "縦列のﾋﾟﾝを基準に貼付ける", "ﾋﾟﾝ･穴のｾﾝﾀｰになる様貼付ける" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :5.ｼｰﾄ(傷防止)貼付確認", "WETE-G002-C12" ] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り貼付け出来ている事", "Method": "目視", "RecordMethod": "WETE-G002-C12", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍﾞｰｽ組立_ﾍﾞｱﾘﾝｸﾞ圧入", "WorkItems": [ "1. に を取付ける" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ﾍﾞｰｽ組立_底面ﾍﾞｱﾘﾝｸﾞ取付け", "WorkItems": [ "1. に を で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ﾍﾞｰｽ組立_ﾌﾞﾛｯｸ取付け", "WorkItems": [ "1. に を挿入しBOLT で取付ける" ], "WorkPoints": [ "ﾃｰﾊﾟｰ側を下にして挿入する" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "95cN･m", "WorkName": "ﾍﾞｰｽ組立_ｽﾍﾟｰｻｰ・ｶﾊﾞｰ取付け", "WorkItems": [ "1. に を で取付ける", "2. 1完成品に を で取付ける" ], "WorkPoints": [ "面を合わせる事" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m", "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍﾞｰｽ組立_ｸﾞﾘｰｽ塗布", "WorkItems": [ "◆1. のﾍﾞｱﾘﾝｸﾞにｸﾞﾘｰｽを塗布する" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:各1", "ｸﾞﾘｰｽ塗布 米粒:各2" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:各1・2", "Method": "目視", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "ｶﾞｲﾄﾞ前組み", "WorkItems": [ "1. にGUIDE をBOLT で取付ける" ], "WorkPoints": [ "定盤に当付けて取付けの事" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ｼｬｯﾀｰ前組み", "WorkItems": [ "2. 1完成品を定盤上で本締結する", "1. SHUTTER にCOLLAR GUIDE BLOCK をBOLT で仮取付けする" ], "WorkPoints": [ "SHUTTER GUIDE BLOCK を定盤に当付けて締結の事" ], "Tolks": [ "締付ﾄﾙｸ 95cN･mcN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｼｬｯﾀｰ前組み", "WorkItems": [ "2. 1完成品を定盤上で本締結する", "1. SHUTTER にCOLLAR GUIDE BLOCK をBOLT で仮取付けする" ], "WorkPoints": [ "隙間無い事", "面を合わせる事", "SHUTTER GUIDE BLOCK を定盤に当付けて締結の事" ], "Tolks": [ "締付ﾄﾙｸ 95cN･mcN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "作業確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｼｬｯﾀｰ取付け1", "WorkItems": [ "1. に を取付け､ を で仮取付けする" ], "WorkPoints": [ "仮止め:SD-A052924-017にて本締め" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A051321-016にて本締め" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "95cN･m", "WorkName": "ｼｬｯﾀｰ取付け2", "WorkItems": [ "1. を定盤上で本締結する" ], "WorkPoints": [ "ｶﾞｲﾄﾞを定盤に当付けて締結の事" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｼｬｯﾀｰ取付け2", "WorkItems": [ "3. ﾍﾞｱﾘﾝｸﾞとｶﾞｲﾄﾞに隙間が無い事を確認する", "1. を定盤上で本締結する", "2. 1完成品のｼｬｯﾀｰ開閉時に､4つのﾍﾞｱﾘﾝｸﾞが回転する事を確認する" ], "WorkPoints": [ "面を合わせる事", "ｶﾞｲﾄﾞを定盤に当付けて締結の事", "面を合わせる事", "４箇所すべて㉙が通ら無い事" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "回転確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り回転出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.02㎜", "ToolOther": "", "WorkName": "ｼｬｯﾀｰ取付け2", "WorkItems": [ "3. ﾍﾞｱﾘﾝｸﾞとｶﾞｲﾄﾞに隙間が無い事を確認する", "2. 1完成品のｼｬｯﾀｰ開閉時に､4つのﾍﾞｱﾘﾝｸﾞが回転する事を確認する" ], "WorkPoints": [ "面を合わせる事", "面を合わせる事", "４箇所すべて㉙が通ら無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.02㎜が通ら無い事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｽﾄｯﾊﾟｰ取付け", "WorkItems": [ "▲1. BOLT に接着剤を塗布する", "2. に を1完成品とWASHER で取付ける" ], "WorkPoints": [ "ﾎﾞﾙﾄの先端に塗布する", "仮取付けする", "シャッターを㉙に当付けて締結する", "矢印方向に当付けの事", "隙間無き事", "㉙を のベースに当付け取付ける", "ﾍﾞｰｽ底面と合わせる事" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "接着剤塗布 米粒:1", "検査表 :3.ｼｬｯﾀｰ位置調整" ] }
{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:1", "Method": "目視", "RecordMethod": "-", "Other": "ﾛｯｸﾀｲﾄ243", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ｽﾄｯﾊﾟｰ取付け", "WorkItems": [ "▲1. BOLT に接着剤を塗布する", "2. に を1完成品とWASHER で取付ける" ], "WorkPoints": [ "ﾎﾞﾙﾄの先端に塗布する" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "接着剤塗布 米粒:1", "検査表 :3.ｼｬｯﾀｰ位置調整", "▲特殊作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "8ﾉｽﾞﾙﾁｪﾝｼﾞｬｰLｼｬｯﾀｰ調整ｼﾞｸﾞ", "Size": "", "ToolOther": "FM-5905", "WorkName": "ｽﾄｯﾊﾟｰ取付け", "WorkItems": [ "▲1. BOLT に接着剤を塗布する", "2. に を1完成品とWASHER で取付ける" ], "WorkPoints": [ "ﾎﾞﾙﾄの先端に塗布する" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "接着剤塗布 米粒:1", "検査表 :3.ｼｬｯﾀｰ位置調整", "▲特殊作業", "WETE-G002-C12" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-5905", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "WETE-G002-C12", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｽﾌﾟﾘﾝｸﾞ取付け", "WorkItems": [ "◆1. のﾋﾟﾝとWASHER にｸﾞﾘｰｽを塗布する", "2. にSPRING を挿入し､GUIDE にWASHER を貼付けBOLT WASHER で取付ける" ], "WorkPoints": [ "ﾍﾞｰｽに対して平行､ﾋﾟﾝがｶﾞｲﾄﾞ穴の中心になるよう取付けの事", "ｼｬｯﾀｰを開閉させｶﾞｲﾄﾞとﾋﾟﾝの干渉が無い事", "ﾋﾟﾝ全体に塗布する", "表裏に塗布する" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:各1", "ｸﾞﾘｰｽ塗布 米粒:2" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:2・ｺﾞﾏ粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ｽﾌﾟﾘﾝｸﾞ取付け", "WorkItems": [], "WorkPoints": [ "ｼｬｯﾀｰを開閉させｶﾞｲﾄﾞとﾋﾟﾝの干渉が無い事", "ﾋﾟﾝ全体に塗布する", "表裏に塗布する" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:各1", "ｸﾞﾘｰｽ塗布 米粒:2", "◆作業者安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "ﾌﾞﾛｯｸ取付け", "WorkItems": [ "1. に を で取付ける" ], "WorkPoints": [ " をﾋﾟﾝに挿入する" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "ｽﾍﾟｰｻｰ・ﾄﾞｸﾞ取付け", "WorkItems": [ "1. に を で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ｽﾍﾟｰｻｰ・ﾄﾞｸﾞ取付け", "WorkItems": [ "2. 1完成品に を で取付ける" ], "WorkPoints": [ "㉙を矢印方向に当付ける", "矢印方向に当付け取付ける" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾁｪﾝｼﾞｬｰﾄﾞｸﾞ_ﾌﾞﾛｯｸ_ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(FC08long)", "Size": "", "ToolOther": "FM-6586", "WorkName": "ｽﾍﾟｰｻｰ・ﾄﾞｸﾞ取付け", "WorkItems": [ "2. 1完成品に を で取付ける" ], "WorkPoints": [ "㉙を矢印方向に当付ける", "矢印方向に当付け取付ける" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-6586", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "T10", "ToolOther": "95cN･m", "WorkName": "識別用ﾌﾞﾛｯｸ取付け", "WorkItems": [ "1. に を で取付ける" ], "WorkPoints": [ "㉘を矢印方向に当付けておく", "㉘を矢印方向に当付け取付ける" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾁｪﾝｼﾞｬｰﾄﾞｸﾞ_ﾌﾞﾛｯｸ_ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(FC08long)", "Size": "", "ToolOther": "FM-6586", "WorkName": "識別用ﾌﾞﾛｯｸ取付け", "WorkItems": [ "1. に を で取付ける" ], "WorkPoints": [ "㉘を矢印方向に当付けておく", "㉘を矢印方向に当付け取付ける" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-6586", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾋﾟﾝ取付け", "WorkItems": [ "2. 1完成品を で取付ける", "◆1. にｸﾞﾘｰｽを塗布する" ], "WorkPoints": [ "長穴側面部に塗布する" ], "Tolks": [ "締付ﾄﾙｸ 41cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:各1", "ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:各2" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:各1・ｺﾞﾏ粒:各2", "Method": "目視", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "4.5", "ToolOther": "41cN･m", "WorkName": "ﾋﾟﾝ取付け", "WorkItems": [ "2. 1完成品を で取付ける", "◆1. にｸﾞﾘｰｽを塗布する" ], "WorkPoints": [ "長穴側面部に塗布する" ], "Tolks": [ "締付ﾄﾙｸ 41cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "◆作業者安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "41cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰﾁｪｯｶｰ機構部", "Size": "", "ToolOther": "FM-6553", "WorkName": "脱着・ｼｬｯﾀｰ動作確認", "WorkItems": [ "1. の脱着確認をする", "2. のｼｬｯﾀｰの動作確認をする" ], "WorkPoints": [ "引っ掛かり無き事", "開くときの最大荷重をｽﾄﾛｰｸ全域で測定する", "ﾚﾊﾞｰを押す" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "WETE-G002-C12" ] }
{ "QualityItem": "脱着確認", "ToolManageNo": "FM-6553", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "引っ掛かりが無い事", "Method": "目視", "RecordMethod": "WETE-G002-C12", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ", "Size": "", "ToolOther": "", "WorkName": "脱着・ｼｬｯﾀｰ動作確認", "WorkItems": [], "WorkPoints": [ "規格値:4.2N以下", "自重落下する事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :1.ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ脱着確認", "検査表 :2.ｼｬｯﾀｰ動作確認", "WETE-G002-C12" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "-", "ToolCycle": "1回/1年", "ToolRecord": "校正成績書", "StdVal": "4.2N以下", "Method": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ", "RecordMethod": "WETE-G002-C12", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾉｽﾞﾙｾｯﾄ確認", "WorkItems": [ "1. ﾉｽﾞﾙのｾｯﾄ確認をする" ], "WorkPoints": [ "引っ掛かりなくｽﾑｰｽﾞである事", "40ヵ所すべて確認する", "ｼｬｯﾀｰを閉じた状態で､ﾉｽﾞﾙが抜け無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :4.ﾉｽﾞﾙｾｯﾄ確認", "WETE-G002-C12" ] }
{ "QualityItem": "作業確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り作業出来ている事", "Method": "目視", "RecordMethod": "WETE-G002-C12", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "銘板貼付け", "WorkItems": [ "1. にLABEL LABEL LABEL を貼付ける" ], "WorkPoints": [ "12㎜", "1㎜", "25㎜", "1.5㎜", "ｼｬｯﾀｰを開けて貼付ける", "㉘を使用し貼付ける", "24㎜", "2㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :6.ﾗﾍﾞﾙ貼付確認" ] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾁｪﾝｼﾞｬｰﾄﾞｸﾞ_ﾌﾞﾛｯｸ_ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(FC08long)", "Size": "", "ToolOther": "FM-6586", "WorkName": "銘板貼付け", "WorkItems": [ "1. にLABEL LABEL LABEL を貼付ける" ], "WorkPoints": [ "12㎜", "1㎜", "25㎜", "1.5㎜", "ｼｬｯﾀｰを開けて貼付ける", "㉘を使用し貼付ける", "24㎜", "2㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表 :6.ﾗﾍﾞﾙ貼付確認" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-6586", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾛｯｸﾌﾞﾗｹｯﾄ組立1", "WorkItems": [ "1. BRACKET にLABEL を貼付ける", "2. PLATE に1完成品をBOLT WASHER で取付ける", "3. 2完成品にINDEX-PLUNGER を取付ける" ], "WorkPoints": [ "6.5㎜", "3㎜", "45㎜" ], "Tolks": [ "締付ﾄﾙｸ 3.2N･m", "締付ﾄﾙｸ 1.8N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "ﾛｯｸﾌﾞﾗｹｯﾄ組立1", "WorkItems": [], "WorkPoints": [ "矢印方向に押し当てて取付けの事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "10㎜", "ToolOther": "1.8N･m", "WorkName": "ﾛｯｸﾌﾞﾗｹｯﾄ組立1", "WorkItems": [ "3. 2完成品にINDEX-PLUNGER を取付ける" ], "WorkPoints": [ "6.5㎜", "3㎜", "45㎜" ], "Tolks": [ "締付ﾄﾙｸ 1.8N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "1.8N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾛｯｸﾌﾞﾗｹｯﾄ組立1", "WorkItems": [ "1. BRACKET にLABEL を貼付ける", "2. PLATE に1完成品をBOLT WASHER で取付ける", "3. 2完成品にINDEX-PLUNGER を取付ける" ], "WorkPoints": [ "6.5㎜", "3㎜", "45㎜" ], "Tolks": [ "締付ﾄﾙｸ 3.2N･m", "締付ﾄﾙｸ 1.8N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾛｯｸﾌﾞﾗｹｯﾄ組立2", "WorkItems": [ "3. にBRACKET をWASHER WASHER BOLT にて取付ける", "◆1. の溝周辺にｸﾞﾘｰｽを塗布する", "◆2. WASHER の外周部分にｸﾞﾘｰｽを塗布する" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 9.8N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:3", "ｸﾞﾘｰｽ塗布 米粒:各1" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:3,各1", "Method": "目視", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "9.8N･m", "WorkName": "ﾛｯｸﾌﾞﾗｹｯﾄ組立2", "WorkItems": [], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 9.8N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:3", "ｸﾞﾘｰｽ塗布 米粒:各1", "◆作業者安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "9.8N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "Size": "6㎜", "ToolOther": "", "WorkName": "ｶﾞｲﾄﾞ(左側)組立1", "WorkItems": [], "WorkPoints": [ "BRACKET の左右端面はBRACKET と揃える ※略図青線部分" ], "Tolks": [ "締付ﾄﾙｸ 9.8N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "1回/3年", "ToolRecord": "校正成績書", "StdVal": "指示通り取付け出来ている事", "Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "定盤", "Size": "", "ToolOther": "", "WorkName": "ｶﾞｲﾄﾞ(左側)組立1", "WorkItems": [], "WorkPoints": [ "BRACKET の左右端面はBRACKET と揃える ※略図青線部分" ], "Tolks": [ "締付ﾄﾙｸ 9.8N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "1回/3年", "ToolRecord": "校正成績書", "StdVal": "下面を定盤上で合わせて固定する事", "Method": "定盤", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "9.8N･m", "WorkName": "ｶﾞｲﾄﾞ(左側)組立1", "WorkItems": [], "WorkPoints": [ "BRACKET の左右端面はBRACKET と揃える ※略図青線部分" ], "Tolks": [ "締付ﾄﾙｸ 9.8N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "9.8N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｶﾞｲﾄﾞ(左側)組立1", "WorkItems": [ "1. BRACKET にBRACKET をBOLT WASHER にて取付ける", "2. 1完成品にCOVER を貼付ける" ], "WorkPoints": [ "30㎜", "定盤とﾌﾞﾛｯｸｹﾞｰｼﾞを利用して､6㎜ｸﾘｱﾗﾝｽにて取付け ※略図黄色表示部分" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "定 盤" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "10.9N･m", "WorkName": "ｶﾞｲﾄﾞ(左側)組立2", "WorkItems": [ "1. にPOST URETHANE をBOLT SPACER BOLT WASHER BOLT にて取付ける" ], "WorkPoints": [ "取付け後､URETHANE の回転を確認する", "半透明にしています" ], "Tolks": [ "締付ﾄﾙｸ 10.9N･m", "締付ﾄﾙｸ 9.8N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "10.9N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "9.8N･m", "WorkName": "ｶﾞｲﾄﾞ(左側)組立2", "WorkItems": [ "1. にPOST URETHANE をBOLT SPACER BOLT WASHER BOLT にて取付ける" ], "WorkPoints": [ "取付け後､URETHANE の回転を確認する", "半透明にしています" ], "Tolks": [ "締付ﾄﾙｸ 10.9N･m", "締付ﾄﾙｸ 9.8N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "9.8N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "3.6N･m", "WorkName": "ｶﾞｲﾄﾞ(左側)組立3", "WorkItems": [ "1. に をBOLT WASHER で取付ける" ], "WorkPoints": [ "矢印方向へ当付け取付けのこと" ], "Tolks": [ "締付ﾄﾙｸ 3.6N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.6N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｶﾞｲﾄﾞ(右側)組立1", "WorkItems": [ "2. 1完成品にCOVER を貼付ける" ], "WorkPoints": [ "目視ｾﾝﾀｰにて傾き無きこと", "30㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null