input stringclasses 1 value | instruction stringlengths 222 1.92k | output stringlengths 193 312 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "70cN･m",
"WorkName": "EMGSW取付",
"WorkItems": [
"■1. SWITCH の型式を確認し,製造番号を検査書に記入する",
"■2. にSWITCH を取付ける",
"3. 2.の完成品にSWITCH の付属ｶﾊﾞｰを取付ける"
],
"WorkPoints": [
"製造番号",
"型式"
],
"Tolks": [
"締付ﾄﾙｸ 70cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"EMG SW : Front",
"22S201",
"11S201",
"21S201",
"32S201",
"31S201",
"12S201",
"EMG SW : Rear",
"22S202",
"11S202",
"21S202",
"32S202",
"31S202",
"12S202",
"検査表SWITCH :4.EMG SW(1)型式･検査書ﾁｪｯｸ",
"検査表SWITCH :4.EMG SW(2)ﾈｼﾞ締めﾄﾙｸ",
"ﾎﾞﾀﾝ部は取り外しｶﾊﾞｰ工程へ払い出す",
"ﾌﾛﾝﾄ､ﾘｱに注意",
"丸端子の方向に注意",
"△印の向きに注意(21S､22S側)",
"△印の向きに注意(11S､12S側)",
"付属ｶﾊﾞｰ",
"確実に取付ける事※上から押さえ付けて取付",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "70cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾚｷﾞｭﾚｰﾀAC30締付治具",
"Size": "",
"ToolOther": "FM-2218",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2218",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "50cN･m",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀｺﾈｸﾀ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾛﾝﾄACｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ前段取り",
"WorkItems": [
"■1. MOTOR-DRIVER MOTOR-DRIVER の型式確認､ｼﾘｱﾙNo.を検査表に記入する",
"2. ﾛｰﾀﾘｰSW､DIP-SWを設定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FY軸ﾄﾞﾗｲﾊﾞ",
"FX軸ﾄﾞﾗｲﾊﾞ",
"電源ｺﾈｸﾀ;※B2工程前準備工程へ渡す",
"電源ｺﾈｸﾀ;※B2工程前準備工程へ渡す",
"検査表MOTOR-DRIVER :2.ﾄﾞﾗｲﾊﾞｰ設定(1)型式･検査書ﾁｪｯｸ",
"検査表MOTOR-DRIVER :2.ﾄﾞﾗｲﾊﾞｰ設定(2)負荷設定確認",
"ﾛｰﾀﾘｰSW設定:0",
"ﾛｰﾀﾘｰSW設定:1",
"DIP-SW設定:全てOFF",
"DIP-SW設定:4のみON",
"型式",
"ｼﾘｱﾙNo.",
"型式",
"ｼﾘｱﾙNo.",
"WETE-G002-D04"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､製造番号転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾛﾝﾄACｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ前段取り",
"WorkItems": [
"■1. MOTOR-DRIVER MOTOR-DRIVER の型式確認､ｼﾘｱﾙNo.を検査表に記入する",
"2. ﾛｰﾀﾘｰSW､DIP-SWを設定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FY軸ﾄﾞﾗｲﾊﾞ",
"FX軸ﾄﾞﾗｲﾊﾞ",
"電源ｺﾈｸﾀ;※B2工程前準備工程へ渡す",
"電源ｺﾈｸﾀ;※B2工程前準備工程へ渡す",
"検査表MOTOR-DRIVER :2.ﾄﾞﾗｲﾊﾞｰ設定(1)型式･検査書ﾁｪｯｸ",
"検査表MOTOR-DRIVER :2.ﾄﾞﾗｲﾊﾞｰ設定(2)負荷設定確認",
"ﾛｰﾀﾘｰSW設定:0",
"ﾛｰﾀﾘｰSW設定:1",
"DIP-SW設定:全てOFF",
"DIP-SW設定:4のみON",
"型式",
"ｼﾘｱﾙNo.",
"型式",
"ｼﾘｱﾙNo.",
"WETE-G002-D04"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾛﾝﾄﾄﾞﾗｲﾊﾞｰｺﾈｸﾀ接続",
"WorkItems": [
"1. のｺﾈｸﾀｼｮｰﾄ配線を外し､CABLE を接続する",
"2. へ付属治具にてCABLE を接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"付属治具",
"廃棄(ｼｮｰﾄ配線)",
"NK501",
"P4K501",
"P4",
"NK502",
"P6K502",
"P6",
"端子の凹凸面をﾗﾍﾞﾙ側に向ける事",
"端子の凹凸面をﾗﾍﾞﾙ側に向ける事",
"検査表 :2.ﾄﾞﾗｲﾊﾞｰ設定(3)ｺﾈｸﾀ端子接続",
"検査表 :2.ﾄﾞﾗｲﾊﾞｰ設定(3)ｺﾈｸﾀ端子接続",
"付属治具は使用後､取り外す事",
"付属治具は使用後､取り外す事",
"WETE-G002-D04"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾛﾝﾄｺﾝﾃﾞﾝｻｰﾊﾞﾝｸ前段取り",
"WorkItems": [
"■1. MOTOR-DRIVER-PARTS の型式を確認し､ｼﾘｱﾙNo.を検査表に記入する",
"2. 1の完成品へ を接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CNP1B",
"P1BK512",
"検査表MOTOR-DRIVER-PARTS :2.ﾄﾞﾗｲﾊﾞｰ設定(1)型式･検査書ﾁｪｯｸ",
"検査表MOTOR-DRIVER-PARTS :2.ﾄﾞﾗｲﾊﾞｰ設定(3)ｺﾈｸﾀ端子接続",
"型式",
"ｼﾘｱﾙNo.",
"WETE-G002-D04"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､製造番号転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾛﾝﾄｺﾝﾃﾞﾝｻｰﾊﾞﾝｸ前段取り",
"WorkItems": [
"■1. MOTOR-DRIVER-PARTS の型式を確認し､ｼﾘｱﾙNo.を検査表に記入する",
"2. 1の完成品へ を接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CNP1B",
"P1BK512",
"検査表MOTOR-DRIVER-PARTS :2.ﾄﾞﾗｲﾊﾞｰ設定(1)型式･検査書ﾁｪｯｸ",
"検査表MOTOR-DRIVER-PARTS :2.ﾄﾞﾗｲﾊﾞｰ設定(3)ｺﾈｸﾀ端子接続",
"型式",
"ｼﾘｱﾙNo.",
"WETE-G002-D04"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘｱACｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ前段取り",
"WorkItems": [
"■1. MOTOR-DRIVER MOTOR-DRIVER の型式確認､ｼﾘｱﾙNo.を検査表に記入する",
"2. ﾛｰﾀﾘｰSW､DIP-SWを設定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"RY軸ﾄﾞﾗｲﾊﾞ",
"RX軸ﾄﾞﾗｲﾊﾞ",
"電源ｺﾈｸﾀ;※B2工程前準備工程へ渡す",
"電源ｺﾈｸﾀ;※B2工程前準備工程へ渡す",
"検査表MOTOR-DRIVER :2.ﾄﾞﾗｲﾊﾞｰ設定(1)型式･検査書ﾁｪｯｸ",
"検査表MOTOR-DRIVER :2.ﾄﾞﾗｲﾊﾞｰ設定(2)負荷設定確認",
"ﾛｰﾀﾘｰSW設定:2",
"DIP-SW設定:全てOFF",
"ﾛｰﾀﾘｰSW設定:3",
"DIP-SW設定:4のみON",
"ｼﾘｱﾙNo",
"型式",
"ｼﾘｱﾙNo",
"型式",
"WETE-G002-D04"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､製造番号転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘｱACｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ前段取り",
"WorkItems": [
"■1. MOTOR-DRIVER MOTOR-DRIVER の型式確認､ｼﾘｱﾙNo.を検査表に記入する",
"2. ﾛｰﾀﾘｰSW､DIP-SWを設定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"RY軸ﾄﾞﾗｲﾊﾞ",
"RX軸ﾄﾞﾗｲﾊﾞ",
"電源ｺﾈｸﾀ;※B2工程前準備工程へ渡す",
"電源ｺﾈｸﾀ;※B2工程前準備工程へ渡す",
"検査表MOTOR-DRIVER :2.ﾄﾞﾗｲﾊﾞｰ設定(1)型式･検査書ﾁｪｯｸ",
"検査表MOTOR-DRIVER :2.ﾄﾞﾗｲﾊﾞｰ設定(2)負荷設定確認",
"ﾛｰﾀﾘｰSW設定:2",
"DIP-SW設定:全てOFF",
"ﾛｰﾀﾘｰSW設定:3",
"DIP-SW設定:4のみON",
"ｼﾘｱﾙNo",
"型式",
"ｼﾘｱﾙNo",
"型式",
"WETE-G002-D04"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに設定出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘｱﾄﾞﾗｲﾊﾞｰｺﾈｸﾀ接続",
"WorkItems": [
"1. のｺﾈｸﾀｼｮｰﾄ配線を外し､CABLE を接続する",
"2. へ付属治具にてCABLE を接続,する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"付属治具",
"廃棄(ｼｮｰﾄ配線)",
"NK503",
"P4K503",
"P4",
"NK504",
"P6K504",
"P6",
"端子の凹凸面をﾗﾍﾞﾙ側に向ける事",
"端子の凹凸面をﾗﾍﾞﾙ側に向ける事",
"検査表 :2.ﾄﾞﾗｲﾊﾞｰ設定(3)ｺﾈｸﾀ端子接続",
"検査表 :2.ﾄﾞﾗｲﾊﾞｰ設定(3)ｺﾈｸﾀ端子接続",
"付属治具は使用後､取り外す事",
"付属治具は使用後､取り外す事",
"WETE-G002-D04"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘｱｺﾝﾃﾞﾝｻｰﾊﾞﾝｸ前段取り",
"WorkItems": [
"■1. MOTOR-DRIVER-PARTS の型式を確認し､ｼﾘｱﾙNo.を検査表に記入する",
"2. 1の完成品へ を接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CNP1B",
"P1BK514",
"検査表MOTOR-DRIVER-PARTS :2.ﾄﾞﾗｲﾊﾞｰ設定(1)型式･検査書ﾁｪｯｸ",
"検査表MOTOR-DRIVER-PARTS :2.ﾄﾞﾗｲﾊﾞｰ設定(3)ｺﾈｸﾀ端子接続",
"型式",
"ｼﾘｱﾙNo.",
"WETE-G002-D04"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､製造番号転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘｱｺﾝﾃﾞﾝｻｰﾊﾞﾝｸ前段取り",
"WorkItems": [
"■1. MOTOR-DRIVER-PARTS の型式を確認し､ｼﾘｱﾙNo.を検査表に記入する",
"2. 1の完成品へ を接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CNP1B",
"P1BK514",
"検査表MOTOR-DRIVER-PARTS :2.ﾄﾞﾗｲﾊﾞｰ設定(1)型式･検査書ﾁｪｯｸ",
"検査表MOTOR-DRIVER-PARTS :2.ﾄﾞﾗｲﾊﾞｰ設定(3)ｺﾈｸﾀ端子接続",
"型式",
"ｼﾘｱﾙNo.",
"WETE-G002-D04"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ前段取り(ﾌﾛﾝﾄﾄﾞﾗｲﾊﾞｰｺﾈｸﾀｰ取付)",
"WorkItems": [
"■1. の型式ﾁｪｯｸ､ｼﾘｱﾙNo.､検査書有無を検査表に記入する",
"2. 1の完成品へ を接続する"
],
"WorkPoints": [
"端子の凸凹面をﾗﾍﾞﾙ側に向け接続する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｼﾘｱﾙNo.",
"L11K501",
"L11",
"L1K502",
"L21",
"L21K501",
"L1",
"FX軸ﾄﾞﾗｲﾊﾞｰ",
"FY軸ﾄﾞﾗｲﾊﾞｰ",
"L11",
"L21",
"L11K502",
"L21K502",
"FY軸ﾄﾞﾗｲﾊﾞｰ配線",
"L2K502",
"L3K502",
"L2",
"L3",
"検査表 :1.電源部(1)型式･検査書ﾁｪｯｸ",
"検査表 :2.ﾄﾞﾗｲﾊﾞｰ設定(3)ｺﾈｸﾀ端子接続",
"WETE-G002-D04"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､製造番号転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ前段取り(ﾌﾛﾝﾄﾄﾞﾗｲﾊﾞｰｺﾈｸﾀｰ取付)",
"WorkItems": [
"■1. の型式ﾁｪｯｸ､ｼﾘｱﾙNo.､検査書有無を検査表に記入する",
"2. 1の完成品へ を接続する"
],
"WorkPoints": [
"端子の凸凹面をﾗﾍﾞﾙ側に向け接続する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｼﾘｱﾙNo.",
"L11K501",
"L11",
"L1K502",
"L21",
"L21K501",
"L1",
"FX軸ﾄﾞﾗｲﾊﾞｰ",
"FY軸ﾄﾞﾗｲﾊﾞｰ",
"L11",
"L21",
"L11K502",
"L21K502",
"FY軸ﾄﾞﾗｲﾊﾞｰ配線",
"L2K502",
"L3K502",
"L2",
"L3",
"検査表 :1.電源部(1)型式･検査書ﾁｪｯｸ",
"検査表 :2.ﾄﾞﾗｲﾊﾞｰ設定(3)ｺﾈｸﾀ端子接続",
"WETE-G002-D04"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ前段取り(ﾘｱﾄﾞﾗｲﾊﾞｰｺﾈｸﾀｰ取付)",
"WorkItems": [
"2. 1の完成品へ を接続する",
"1. へ を接続する"
],
"WorkPoints": [
"端子の凸凹面をﾗﾍﾞﾙ側に向け接続する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"L11K503",
"L11",
"L21",
"L1K504",
"L3",
"L2",
"L1",
"RX軸ﾄﾞﾗｲﾊﾞｰ",
"RY軸ﾄﾞﾗｲﾊﾞｰ",
"RY軸ﾄﾞﾗｲﾊﾞｰ配線",
"L21K503",
"L11",
"L21",
"L11K504",
"L21K504",
"L2K504",
"L3K504",
"検査表 :2.ﾄﾞﾗｲﾊﾞｰ設定(3)ｺﾈｸﾀ端子接続確認",
"検査表 :2.ﾄﾞﾗｲﾊﾞｰ設定(3)ｺﾈｸﾀ端子接続",
"WETE-G002-D04"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPU-BOX前段取り",
"WorkItems": [
"■1. の製造番号を検査表に記入する",
"2. にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"BFG",
"UNI01*-BKT"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :6.その他(1)型式･検査書ﾁｪｯｸ-1",
"番号を記入",
" とBRACKET の下面を合わせる",
"WETE-G002-D04"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.2N･m",
"WorkName": "CPU-BOX前段取り",
"WorkItems": [
"■1. の製造番号を検査表に記入する",
"2. にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"BFG",
"UNI01*-BKT"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :6.その他(1)型式･検査書ﾁｪｯｸ-1",
"番号を記入",
" とBRACKET の下面を合わせる",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CN中継基板(搬送)前段取り",
"WorkItems": [
"■1. PCB-COM の型式を確認し､製造番号を記入する",
"3. 基板をｴｱｰﾏｯﾄで梱包し､K323及びK324を表記する",
"2. ｺﾝﾍﾞﾔｰ仕様を確認し､ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様のみK323へCABLE をCNB5へ接続する"
],
"WorkPoints": [
"【ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様】K323⇒CABLE ｼｮｰﾄｺﾈｸﾀあり:1枚/K324⇒CABLE ｼｮｰﾄｺﾈｸﾀなし:1枚【ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様】K323､K324⇒CABLE ｼｮｰﾄｺﾈｸﾀなし:2枚"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CNB5",
"K323",
"K324",
"ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様",
"K323",
"K324",
"ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様",
"検査表PCB-COM :3.基板関係(1)型式･検査書ﾁｪｯｸ-3､4",
"製造番号",
"型式",
"WETE-G002-D04"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､製造番号転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CN中継基板(I/O)前段取り",
"WorkItems": [
"■1. PCB-COM の型式を確認し､製造番号を記入する",
"2. 基板をｴｱｰﾏｯﾄで梱包し､K321及びK322を表記する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表PCB-COM :3.基板関係(1)型式･検査書ﾁｪｯｸ-1､2",
"型式",
"製造番号",
"WETE-G002-D04"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､製造番号転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN前段取り",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WETE-G002-D04"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､製造番号転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "FAN組立(架台下用)",
"WorkItems": [
"1. へFAN-GUARD をBOLT WASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"FAN-GUARD の取付け方向に注意"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "78cN･m",
"WorkName": "FAN組立(真空ﾎﾟﾝﾌﾟ冷却用)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "78cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "真空ﾎﾟﾝﾌﾟ前段取り",
"WorkItems": [
"■1. PUMP の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"2. PUMP に を取付ける"
],
"WorkPoints": [
"外箱に検査表有り"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"型式",
"製造番号",
"検査表PUMP :6.その他(1)型式･検査書ﾁｪｯｸ-5",
"30㎜",
"WETE-G002-D04"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､製造番号転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "真空ﾎﾟﾝﾌﾟ前段取り",
"WorkItems": [
"■1. PUMP の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"2. PUMP に を取付ける"
],
"WorkPoints": [
"外箱に検査表有り"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"型式",
"製造番号",
"検査表PUMP :6.その他(1)型式･検査書ﾁｪｯｸ-5",
"30㎜",
"■安全作業"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "真空ﾌｨﾙﾀｰ組立①",
"WorkItems": [
"1. NIPPLE へ㉖を巻く",
"2. へ1の完成品を取付ける"
],
"WorkPoints": [
"ｼｰﾙﾃｰﾌﾟを2回転半巻く",
"巻き付け方向注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "真空ﾌｨﾙﾀｰ組立②",
"WorkItems": [
"1. へJOINT JOINT を取付ける",
"2. 1の完成品へJOINT JOINT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"4.5~5.5㎜※緩める方向に調整禁止",
"22~23㎜※緩める方向に調整禁止"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "真空ﾌｨﾙﾀｰ組立③",
"WorkItems": [
"1. COVER へLABEL LABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"54mm",
"128mm",
"96mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "24㎜",
"ToolOther": "15.0N･m",
"WorkName": "真空ﾌｨﾙﾀｰ組立④",
"WorkItems": [
"1. へPLATE を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 15.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"付属ﾅｯﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "真空ﾌｨﾙﾀｰ組立④",
"WorkItems": [
"3. TUBE を指定の長さに切断､番号を記入し､2の完成品へ接続する"
],
"WorkPoints": [
"両端より約50㎜に配管番号を記入する事 ･配管(白) ⇒ 青ﾏｯｷｰ使用"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "真空ﾌｨﾙﾀｰ組立④",
"WorkItems": [
"3. TUBE を指定の長さに切断､番号を記入し､2の完成品へ接続する"
],
"WorkPoints": [
"両端より約50㎜に配管番号を記入する事 ･配管(白) ⇒ 青ﾏｯｷｰ使用"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "60cN･m",
"WorkName": "ｹﾞｰｼﾞ組立①",
"WorkItems": [],
"WorkPoints": [
"ｹﾞｰｼﾞの設定目盛りの外側に調整",
"上部凹みとｶﾊﾞｰ合わせﾏｰｸが合った事を確認する事"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｹﾞｰｼﾞ組立②",
"WorkItems": [
"2. 1の完成品へJOINT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "90cN･m",
"WorkName": "圧力ｾﾝｻ組立",
"WorkItems": [
"1. SENSOR へJOINT をSENSOR へJOINT を取付ける",
"2. 1の完成品へSENSOR SENSOR の付属品(黒枠)を取付ける"
],
"WorkPoints": [
"割れに注意してﾂﾒ4箇所挿入"
],
"Tolks": [
"締付ﾄﾙｸ 90cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"付属品(黒枠)※ﾓﾆﾀｰ面から挿入",
"SENSOR 型式:DP-002Z",
"SENSOR 型式:DP-001Z"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｹﾞｰｼﾞ取付ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-2879",
"WorkName": "ｹﾞｰｼﾞ取付",
"WorkItems": [
"1. BRACKET へ ⇒ ⇒ の順に取付ける"
],
"WorkPoints": [
"BRACKET の凹部(位置決め)と の凸部を合わせる事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"負圧ｹﾞｰｼﾞ 範囲:-100~0KPa",
"正圧ｹﾞｰｼﾞ 範囲:0~0.2MPa",
"正圧ｹﾞｰｼﾞ 範囲:0~1MPa"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2879",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "圧力ｾﾝｻ取付",
"WorkItems": [
"2. TUBE を指定の長さに切断､番号を記入し､1の完成品へ接続する",
"1. へ を の付属品(白枠)で取付ける"
],
"WorkPoints": [
"両端より約50㎜に配管番号を記入する事 ･配管(黒) ⇒ 黄色ﾏｰｶｰ使用"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"付属品(白枠)",
"型式:DP-001Z",
"型式:DP-002Z",
"OK",
"NG:挿入不完全",
"型式:DP-002Z"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｹﾞｰｼﾞﾕﾆｯﾄﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. へBRACKET をNUT BOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"端面合わせ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｹﾞｰｼﾞﾕﾆｯﾄﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. へBRACKET をNUT BOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5mm",
"端面合わせ"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾚｷﾞｭﾚｰﾀAR20締付治具",
"Size": "",
"ToolOther": "FM-2217",
"WorkName": "ﾚｷﾞｭﾚｰﾀ部組立①",
"WorkItems": [
"1. BRACKET にREGULATOR REGULATOR を取付ける"
],
"WorkPoints": [
"BRACKET の凹部(位置決め)とREGULATOR REGULATOR の凸部を合わせる事"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2217",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "3.6N･m",
"WorkName": "ﾚｷﾞｭﾚｰﾀ部組立①",
"WorkItems": [
"1. BRACKET にREGULATOR REGULATOR を取付ける"
],
"WorkPoints": [
"BRACKET の凹部(位置決め)とREGULATOR REGULATOR の凸部を合わせる事"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "17㎜",
"ToolOther": "11N･m",
"WorkName": "ﾚｷﾞｭﾚｰﾀ部組立②",
"WorkItems": [
"1. にREGULATOR を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 11N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"付属ﾜｯｼｬｰ※ｴｯｼﾞ下向き",
"付属ﾅｯﾄ",
"A矢視図",
"A矢視",
"平行に取付け"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾚｷﾞｭﾚｰﾀ部組立②",
"WorkItems": [
"2. 1の完成品のｴｱｰ圧(出代)を調整し､ﾛｯｸする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"33㎜",
"付属ﾅｯﾄ"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾚｷﾞｭﾚｰﾀ部組立③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ﾏｰｷﾝｸﾞ箇所を合わせ束ねる"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｶｯﾀｰﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"1. BRACKET へMANIFOLD をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "17㎜",
"ToolOther": "11N･m",
"WorkName": "交換台車用ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"2. TUBE を指定の長さに切断､番号を記入し､1の完成品へ接続する",
"1. BRACKET へJOINT を取付ける"
],
"WorkPoints": [
"両端より約50㎜に配管番号を記入する事 ･配管(黒) ⇒ 黄色ﾏｰｶｰ使用",
"FL､FR､RL､RRで識別する事"
],
"Tolks": [
"締付ﾄﾙｸ 11N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを4個製作",
"A矢視"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各11N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "交換台車用ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"2. TUBE を指定の長さに切断､番号を記入し､1の完成品へ接続する",
"1. BRACKET へJOINT を取付ける"
],
"WorkPoints": [
"両端より約50㎜に配管番号を記入する事 ･配管(黒) ⇒ 黄色ﾏｰｶｰ使用",
"FL､FR､RL､RRで識別する事"
],
"Tolks": [
"締付ﾄﾙｸ 11N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを4個製作",
"A矢視"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ配管準備",
"WorkItems": [
"1. TUBE を指定の長さに切断､番号を記入する",
"3. 1の完成品を2の完成品に接続する"
],
"WorkPoints": [
"両端より約50㎜に配管番号を記入する事 ･配管(黒) ⇒ 黄色ﾏｰｶｰ使用",
"FT11の向きに注意し接続する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"212L",
"212R",
"K068-1"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "60cN･m",
"WorkName": "OP;ﾌﾛﾝﾄ台車駆動ﾊﾞﾙﾌﾞ組立(左側;ITF17連台車+右側;ITF17連台車)",
"WorkItems": [
"1. BRACKET へVALVE VALVE を㉓BOLT で取付ける",
"2. 1の完成品へ を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"4番ﾎﾟｰﾄ",
"212R",
"212L"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "OP;ﾌﾛﾝﾄ台車駆動ﾊﾞﾙﾌﾞ組立(左側;ITF17連台車切替仕様+右側;ITF17連台車)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "60cN･m",
"WorkName": "OP;ﾌﾛﾝﾄ台車駆動ﾊﾞﾙﾌﾞ組立(左側;ﾄﾚｲﾌｨｰﾀﾞｰ+右側;ITF17連台車)",
"WorkItems": [
"1. BRACKET へVALVE をBOLT WASHER で取付ける",
"2. 1の完成品へ JOINT を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"4番ﾎﾟｰﾄ",
"212R",
"212L"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "60cN･m",
"WorkName": "OP;ﾌﾛﾝﾄ台車駆動ﾊﾞﾙﾌﾞ組立(ITF30連台車)",
"WorkItems": [
"1. BRACKET へVALVE をBOLT WASHER で取付け､JOINT を接続する",
"2. 1の完成品へ JOINT を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"4番ﾎﾟｰﾄ",
"212R",
"212L"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "60cN･m",
"WorkName": "OP;ﾘｱ台車駆動ﾊﾞﾙﾌﾞ組立(左側;ITF17連台車+右側;ITF17連台車)",
"WorkItems": [
"1. BRACKET へVALVE VALVE を㉓BOLT で取付ける",
"2. 1の完成品へ を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"4番ﾎﾟｰﾄ",
"221R",
"221L"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "OP;ﾘｱ台車駆動ﾊﾞﾙﾌﾞ組立(左側;ITF17連台車切替仕様+右側;ITF17連台車)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "60cN･m",
"WorkName": "OP;ﾘｱ台車駆動ﾊﾞﾙﾌﾞ組立(左側;ﾄﾚｲﾌｨｰﾀﾞｰ+右側;ITF17連台車)",
"WorkItems": [
"1. BRACKET へVALVE をBOLT WASHER で取付ける",
"2. 1の完成品へ JOINT を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"4番ﾎﾟｰﾄ",
"221R",
"221L"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "60cN･m",
"WorkName": "OP;ﾘｱ台車駆動ﾊﾞﾙﾌﾞ組立(ITF30連台車)",
"WorkItems": [
"1. BRACKET へVALVE をBOLT WASHER で取付け､JOINT を接続する",
"2. 1の完成品へ JOINT を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"4番ﾎﾟｰﾄ",
"221R",
"221L"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "60cN･m",
"WorkName": "【ﾌﾛﾝﾄ側ﾄﾚｲ仕様】ｺﾈｸﾀﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"2. 1の完成品へCONNECTOR CONNECTOR をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｺﾈｸﾀの向きに注意"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "60cN･m",
"WorkName": "【ﾌﾛﾝﾄ側ﾄﾚｲ切替仕様】ｺﾈｸﾀﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"2. 1の完成品へCONNECTOR CONNECTOR をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｺﾈｸﾀの向きに注意"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "60cN･m",
"WorkName": "【ﾘｱ側ﾄﾚｲ仕様】ｺﾈｸﾀﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"2. 1の完成品へCONNECTOR CONNECTOR をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｺﾈｸﾀの向きに注意"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "60cN･m",
"WorkName": "【ﾘｱ側ﾄﾚｲ切替仕様】ｺﾈｸﾀﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"2. 1の完成品へCONNECTOR CONNECTOR をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｺﾈｸﾀの向きに注意"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "左側ﾏﾆﾎｰﾙﾄﾞ組立",
"WorkItems": [
"1. MANIFOLD へJOINT を取付ける",
"2. 1の完成品へJOINT JOINT JOINT JOINT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります｡",
"33㎜",
"本体取付け穴",
"付属品(ｼｰﾙ付六角穴付ﾌﾟﾗｸﾞ)不要"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "JOINT組立(XY軸ﾍﾞｱ配管)",
"WorkItems": [
"1. JOINT JOINT CABLE-SUPPORT を㉖で束ねる"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "5m",
"ToolOther": "",
"WorkName": "左側束配管準備",
"WorkItems": [
"1. TUBE TUBE TUBE TUBE TUBE TUBE を指定の長さに切断､番号を記入する"
],
"WorkPoints": [
"両端より約50㎜に配管番号を記入する事 ･配管(黒) ⇒ 黄色ﾏｰｶｰ使用 ･配管(白/黄) ⇒ 青ﾏｯｷｰ使用"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱ配管ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6371",
"WorkName": "左側束配管制作1",
"WorkItems": [
"1. ㉖へ を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6371",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱ配管ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6371",
"WorkName": "左側束配管製作2",
"WorkItems": [
"1. を引き回す"
],
"WorkPoints": [
"S(始点)を基準にG(終点)まで引き回す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"702RG(φ8白)",
"701RG(φ8白)",
"701RS(φ8白)",
"702RS(φ8白)"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6371",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配管されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱ配管ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6371",
"WorkName": "左側束配管製作3",
"WorkItems": [
"1. を引き回す"
],
"WorkPoints": [
"S(始点)を基準にG(終点)まで引き回す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"702LS(φ8白)",
"701LS(φ8白)",
"702LG(φ8白)",
"701LG(φ8白)"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6371",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配管されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱ配管ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6371",
"WorkName": "左側束配管製作4",
"WorkItems": [
"1. を引き回す"
],
"WorkPoints": [
"S(始点)を基準にG(終点)まで引き回す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"301S(φ6黄)",
"301G(φ6黄)",
"302S(φ6黄)",
"302G(φ6黄)",
"201RS(φ6黒)",
"201RG(φ6黒)"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6371",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配管されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱ配管ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6371",
"WorkName": "左側束配管製作5",
"WorkItems": [
"1. を引き回す"
],
"WorkPoints": [
"S(始点)を基準にG(終点)まで引き回す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"215RG(φ6黒)",
"215RS(φ6黒)",
"216RG(φ6黒)",
"216RS(φ6黒)"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6371",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配管されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱ配管ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6371",
"WorkName": "左側束配管製作6",
"WorkItems": [
"1. を引き回す"
],
"WorkPoints": [
"S(始点)を基準にG(終点)まで引き回す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"303FG(φ6黄)",
"303FS(φ6黄)",
"802G(φ12黒)",
"802S(φ12黒)",
"203R",
"202L",
"205F",
"203L",
"201L",
"505L",
"504L"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6371",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配管されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱ配管ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6371",
"WorkName": "左側束配管製作7",
"WorkItems": [
"1. を引き回す"
],
"WorkPoints": [
"S(始点)を基準にG(終点)まで引き回す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"202LG(φ6黒)",
"202LS(φ6黒)",
"203RG(φ6黒)",
"203RS(φ6黒)",
"203R",
"202L",
"205F",
"203L",
"201L",
"505L",
"504L"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6371",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配管されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱ配管ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6371",
"WorkName": "左側束配管製作8",
"WorkItems": [
"1. を引き回す"
],
"WorkPoints": [
"S(始点)を基準にG(終点)まで引き回す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"501G(φ8黒)",
"501S(φ8黒)",
"502G(φ8黒)",
"502S(φ8黒)",
"503G(φ8黒)",
"503S(φ8黒)",
"203R",
"202L",
"205F",
"203L",
"201L",
"505L",
"504L"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6371",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配管されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱ配管ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6371",
"WorkName": "左側束配管製作9",
"WorkItems": [
"1. を引き回す"
],
"WorkPoints": [
"S(始点)を基準にG(終点)まで引き回す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"504LG(φ8黒)",
"504LS(φ8黒)",
"505LG(φ8黒)",
"505LS(φ8黒)",
"203R",
"202L",
"205F",
"203L",
"201L",
"505L",
"504L"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6371",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配管されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱ配管ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6371",
"WorkName": "左側束配管製作10",
"WorkItems": [
"1. を引き回す"
],
"WorkPoints": [
"S(始点)を基準にG(終点)まで引き回す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"201LS(φ6黒)",
"201LG(φ6黒)",
"203LG(φ6黒)",
"203LS(φ6黒)",
"203R",
"202L",
"205F",
"203L",
"201L",
"505L",
"504L",
"205FG(φ6黒)",
"205FS(φ6黒)"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6371",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配管されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱ配管ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6371",
"WorkName": "左側束配管製作11",
"WorkItems": [
"1. を引き回す"
],
"WorkPoints": [
"S(始点)を基準にG(終点)まで引き回す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"203R",
"202L",
"205F",
"203L",
"201L",
"505L",
"504L",
"211G(φ6黒)",
"211S(φ6黒)"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6371",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配管されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱ配管ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6371",
"WorkName": "左側束配管製作12",
"WorkItems": [
"1. を引き回す"
],
"WorkPoints": [
"S(始点)を基準にG(終点)まで引き回す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"401G(φ6白)",
"401S(φ6白)",
"303RG(φ6黄)",
"303RS(φ6黄)"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6371",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配管されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱ配管ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6371",
"WorkName": "左側束配管製作13",
"WorkItems": [
"1. を引き回す"
],
"WorkPoints": [
"S(始点)を基準にG(終点)まで引き回す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"213RG(φ6黒)",
"213RS(φ6黒)",
"214RG(φ6黒)",
"214RS(φ6黒)"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6371",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配管されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱ配管ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6371",
"WorkName": "左側束配管製作14",
"WorkItems": [
"1. を引き回す"
],
"WorkPoints": [
"S(始点)を基準にG(終点)まで引き回す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"801G(φ12黒)",
"801S(φ12黒)",
"203R",
"202L",
"205F",
"203L",
"201L",
"505L",
"504L"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "FM-6371",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配管されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱ配管ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6371",
"WorkName": "左側束配管製作15",
"WorkItems": [
"1. 配管を整え､結束する"
],
"WorkPoints": [
"結束及びCABLE-SUPPORT の取付位置はﾊｰﾈｽ板を参照"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6371",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱ配管ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6371",
"WorkName": "左側束配管製作16",
"WorkItems": [
"1. 配管を整え､結束する"
],
"WorkPoints": [
"結束及びCABLE-SUPPORT の取付位置はﾊｰﾈｽ板を参照"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6371",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱ配管ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6371",
"WorkName": "左側束配管製作17",
"WorkItems": [
"1. へ配管を接続する"
],
"WorkPoints": [
"接続位置はﾊｰﾈｽ板を参照"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"701L",
"702L",
"201L",
"701R",
"702R",
"201R"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6371",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "右側ﾏﾆﾎｰﾙﾄﾞ組立",
"WorkItems": [
"1. MANIFOLD へJOINT JOINT を取付ける",
"2. 1の完成品へJOINT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"34.5㎜",
"取付け方向に注意!この部品には方向性があります｡",
"44.5㎜",
"本体取付け穴",
"付属品(ｼｰﾙ付六角穴付ﾌﾟﾗｸﾞ)不要"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "5m",
"ToolOther": "",
"WorkName": "右側配管準備",
"WorkItems": [
"1. TUBE TUBE を下記表の長さに切断する"
],
"WorkPoints": [
"両端より約50㎜に配管番号を記入する事 ･配管(白/黄) ⇒ 青ﾏｯｷｰ使用 ･配管(黒) ⇒ 黄色ﾏｰｶｰ使用"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側配管製作",
"WorkItems": [
"1. へ を接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"204R",
"202R",
"205R",
"204L",
"505R",
"504R"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "19㎜",
"ToolOther": "39.0N･m",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立(左前、右後)①",
"WorkItems": [
"1. PLATE へNUT SCREW を取付ける",
"2. 1の完成品へNUT WASHER STOPPER を取付ける",
"1. PLATE へNUT SCREW を取付ける",
"2. 1の完成品へNUT WASHER STOPPER を取付ける"
],
"WorkPoints": [
"SCREW の挿入面に注意",
"NUT をﾛｯｸする事",
"NUT の面取り向き注意",
"NUT の面取り向き注意",
"SCREW の挿入面に注意",
"NUT をﾛｯｸする事",
"NUT の面取り向き注意",
"NUT の面取り向き注意"
],
"Tolks": [
"締付ﾄﾙｸ 39.0N･m",
"締付ﾄﾙｸ 39.0N･m",
"締付ﾄﾙｸ 39.0N･m",
"締付ﾄﾙｸ 39.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"切り欠き",
"穴3個が下に向く",
"この作業では同じものを2個製作",
"切り欠き",
"穴3個が下に向く"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "39.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸ﾒｶｽﾄｯﾊﾟｰ用ｾｯﾄﾋﾞｽ出代調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6633",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立(左前、右後)①",
"WorkItems": [
"1. PLATE へNUT SCREW を取付ける",
"2. 1の完成品へNUT WASHER STOPPER を取付ける"
],
"WorkPoints": [
"SCREW の挿入面に注意",
"NUT をﾛｯｸする事",
"NUT の面取り向き注意",
"NUT の面取り向き注意"
],
"Tolks": [
"締付ﾄﾙｸ 39.0N･m",
"締付ﾄﾙｸ 39.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"切り欠き",
"穴3個が下に向く"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6633",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸ﾒｶｽﾄｯﾊﾟｰｾｯﾄﾋﾞｽ締結用置台",
"Size": "",
"ToolOther": "FM-6667",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立(左前、右後)①",
"WorkItems": [
"1. PLATE へNUT SCREW を取付ける",
"2. 1の完成品へNUT WASHER STOPPER を取付ける"
],
"WorkPoints": [
"SCREW の挿入面に注意",
"NUT をﾛｯｸする事",
"NUT の面取り向き注意",
"NUT の面取り向き注意"
],
"Tolks": [
"締付ﾄﾙｸ 39.0N･m",
"締付ﾄﾙｸ 39.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"基準:41.5mm",
"止まり:41.0mm",
"通り:42.0mm",
"41.5mmに調整し､通り42.0mm止まり41.0mmで確認する",
"3.3~4.3mm",
"切り欠き",
"穴3個が下に向く",
"面取り",
"面取り"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6667",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立(左前、右後)①",
"WorkItems": [
"1. PLATE へNUT SCREW を取付ける",
"2. 1の完成品へNUT WASHER STOPPER を取付ける"
],
"WorkPoints": [
"SCREW の挿入面に注意",
"NUT をﾛｯｸする事",
"NUT の面取り向き注意",
"NUT の面取り向き注意"
],
"Tolks": [
"締付ﾄﾙｸ 39.0N･m",
"締付ﾄﾙｸ 39.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"切り欠き",
"穴3個が下に向く"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "3.3~4.3㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立(左前、右後)②",
"WorkItems": [
"1. へCLIP をBOLT で取付ける"
],
"WorkPoints": [
"ｽﾄｯﾊﾟｰと反対の面にCLIP を取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "19㎜",
"ToolOther": "39.0N･m",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立(右前、左後)①",
"WorkItems": [
"1. PLATE へNUT SCREW を取付ける",
"2. 1の完成品へNUT WASHER STOPPER を取付ける",
"1. PLATE へNUT SCREW を取付ける",
"2. 1の完成品へNUT WASHER STOPPER を取付ける"
],
"WorkPoints": [
"SCREW の挿入面に注意",
"NUT をﾛｯｸする事",
"NUT の面取り向き注意",
"NUT の面取り向き注意",
"SCREW の挿入面に注意",
"NUT をﾛｯｸする事",
"NUT の面取り向き注意",
"NUT の面取り向き注意"
],
"Tolks": [
"締付ﾄﾙｸ 39.0N･m",
"締付ﾄﾙｸ 39.0N･m",
"締付ﾄﾙｸ 39.0N･m",
"締付ﾄﾙｸ 39.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"切り欠き",
"穴3個が下に向く",
"この作業では同じものを2個製作",
"切り欠き",
"穴3個が下に向く"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "39.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸ﾒｶｽﾄｯﾊﾟｰ用ｾｯﾄﾋﾞｽ出代調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6633",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立(右前、左後)①",
"WorkItems": [
"1. PLATE へNUT SCREW を取付ける",
"2. 1の完成品へNUT WASHER STOPPER を取付ける"
],
"WorkPoints": [
"SCREW の挿入面に注意",
"NUT をﾛｯｸする事",
"NUT の面取り向き注意",
"NUT の面取り向き注意"
],
"Tolks": [
"締付ﾄﾙｸ 39.0N･m",
"締付ﾄﾙｸ 39.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"切り欠き",
"穴3個が下に向く"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6633",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸ﾒｶｽﾄｯﾊﾟｰｾｯﾄﾋﾞｽ締結用置台",
"Size": "",
"ToolOther": "FM-6667",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立(右前、左後)①",
"WorkItems": [
"1. PLATE へNUT SCREW を取付ける",
"2. 1の完成品へNUT WASHER STOPPER を取付ける"
],
"WorkPoints": [
"SCREW の挿入面に注意",
"NUT をﾛｯｸする事",
"NUT の面取り向き注意",
"NUT の面取り向き注意"
],
"Tolks": [
"締付ﾄﾙｸ 39.0N･m",
"締付ﾄﾙｸ 39.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"切り欠き",
"穴3個が下に向く",
"基準:41.5mm",
"止まり:41.0mm",
"通り:42.0mm",
"41.5mmに調整し､通り42.0mm止まり41.0mmで確認する",
"面取り",
"3.3~4.3mm",
"面取り"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6667",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立(右前、左後)①",
"WorkItems": [
"1. PLATE へNUT SCREW を取付ける",
"2. 1の完成品へNUT WASHER STOPPER を取付ける"
],
"WorkPoints": [
"SCREW の挿入面に注意",
"NUT をﾛｯｸする事",
"NUT の面取り向き注意",
"NUT の面取り向き注意"
],
"Tolks": [
"締付ﾄﾙｸ 39.0N･m",
"締付ﾄﾙｸ 39.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"切り欠き",
"穴3個が下に向く"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "3.3~4.3㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立(右前、左後)②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立(右前、左後)②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立(右前、左後)②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "32㎜",
"ToolOther": "4.0N･m",
"WorkName": "ｹｰﾌﾞﾙｻﾎﾟｰﾄ組立",
"WorkItems": [
"1. PLATE にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 4.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "4.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "部品落下防止ｶﾊﾞｰﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. BRACKET へSPACER をBOLT WASHER で取付ける"
],
"WorkPoints": [
"㉘にクランプさせて作業実施"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを8個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾞﾛﾒｯﾄ前準備",
"WorkItems": [
"1. GROMMET へ切り込みを入れる"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを3個製作",
"縦横切り込み長さ;35㎜~40㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "35~40㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "CPU固定ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. BRACKET へCOVER を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾞﾗｹｯﾄ端面に合わせ貼付ける事",
"ﾌﾞﾗｹｯﾄ端面に合わせ貼付ける事"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.