input stringclasses 1 value | instruction stringlengths 222 1.92k | output stringlengths 193 312 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊｰﾈｽ準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.下記ﾘｽﾄの順番でｹｰﾌﾞﾙを準備する"
]
} | {
"QualityItem": "ｹｰﾌﾞﾙ準備確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り準備出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-5856",
"WorkName": "ﾊｰﾈｽ引き回1",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"L1b/L2b/L3bX101",
"基準:1a/3a/5aF101"
]
} | {
"QualityItem": "引き回経路",
"ToolManageNo": "FM-5856",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-5856",
"WorkName": "ﾊｰﾈｽ引き回2",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"EX101",
"基準:E5X001"
]
} | {
"QualityItem": "引き回経路",
"ToolManageNo": "FM-5856",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-5856",
"WorkName": "ﾊｰﾈｽ引き回3",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"基準:E7X001",
"Ed4X1"
]
} | {
"QualityItem": "引き回経路",
"ToolManageNo": "FM-5856",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-5856",
"WorkName": "ﾊｰﾈｽ引き回4",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
"束線ﾎﾞｰﾄﾞ",
"端子下向き(ﾏｰｸﾁｭｰﾌﾞ↓)",
"端子を釘に下向きで引っかける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"基準:2/4/6bF101/E6X001",
"U/V/WaT001/ET001"
]
} | {
"QualityItem": "引き回経路",
"ToolManageNo": "FM-5856",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-5856",
"WorkName": "ｲﾝｼｭﾛｯｸ固定",
"WorkItems": [
"1. の配線を下図の指示に従いｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "引き回経路",
"ToolManageNo": "FM-5856",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "2.5N･m",
"WorkName": "1次側入力ﾗｲﾝ接続(ﾒｲﾝﾌﾞﾚｰｶｰ)",
"WorkItems": [
"■1. の配線を へ で締結する",
"■2. 検査表のﾁｪｯｸ方法に従ってﾄﾙｸ計測を実施する事",
"3. 2の完成品に､ を で締結する"
],
"WorkPoints": [
"ｻｰｼﾞｷﾗｰが上側",
"ﾌﾞﾚｰｶｰの両ｽﾘｯﾄ",
"ﾌﾞﾚｰｶｰの両ｽﾘｯﾄに 付属品(ｶﾊﾞｰ)を取付､ 付属品(ﾋﾞｽ)にて締結"
],
"Tolks": [
"締付ﾄﾙｸ 2.5N･m",
"締付ﾄﾙｸ 30cN･m",
"締付ﾄﾙｸ 2.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"2aF101 2bF101",
"4aF101 4bF101",
"6aF101 6bF101",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.5N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "30cN･m",
"WorkName": "1次側入力ﾗｲﾝ接続(ﾒｲﾝﾌﾞﾚｰｶｰ)",
"WorkItems": [
"■1. の配線を へ で締結する",
"■2. 検査表のﾁｪｯｸ方法に従ってﾄﾙｸ計測を実施する事",
"3. 2の完成品に､ を で締結する"
],
"WorkPoints": [
"ｻｰｼﾞｷﾗｰが上側",
"ﾌﾞﾚｰｶｰの両ｽﾘｯﾄ",
"ﾌﾞﾚｰｶｰの両ｽﾘｯﾄに 付属品(ｶﾊﾞｰ)を取付､ 付属品(ﾋﾞｽ)にて締結"
],
"Tolks": [
"締付ﾄﾙｸ 2.5N･m",
"締付ﾄﾙｸ 30cN･m",
"締付ﾄﾙｸ 2.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"2aF101 2bF101",
"4aF101 4bF101",
"6aF101 6bF101",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾒｰﾀ",
"Size": "No.2",
"ToolOther": "2.5N･m",
"WorkName": "1次側入力ﾗｲﾝ接続(ﾒｲﾝﾌﾞﾚｰｶｰ)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1aF101",
"3aF101",
"5aF101",
"検査表 :ﾄﾙｸ計測(1)ﾒｲﾝﾌﾞﾚｰｶ -F101",
"■安全作業",
"WEPJ-G002-D09"
]
} | {
"QualityItem": "締付ﾄﾙｸ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "2.5N･m±10%",
"Method": "ﾄﾙｸﾒｰﾀ",
"RecordMethod": "WEPJ-G002-D09",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾒｲﾝｽｲｯﾁﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. NUT-PLATE にBRACKET をBRACKET BOLT WASHER で組付ける"
],
"WorkPoints": [
"下記の通り組付けること",
"目安:4.5㎜",
"目安:2㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"矢視A",
"矢視A"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "2±0.5㎜4.5±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾒｲﾝｽｲｯﾁﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. NUT-PLATE にBRACKET をBRACKET BOLT WASHER で組付ける"
],
"WorkPoints": [
"下記の通り組付けること",
"目安:4.5㎜",
"目安:2㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"矢視A",
"矢視A"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "90cN･m",
"WorkName": "ﾒｲﾝｽｲｯﾁ部組立",
"WorkItems": [
"1. をに をｾｯﾄする",
"2. 1の完成品を に PLATE で組付ける",
"■3. SWの動作確認を行う"
],
"WorkPoints": [
"ｸｯｼｮﾝの破損防止で外す",
"左側をONの向きにする",
"ON",
"OFF",
"K007-1",
" のﾚﾊﾞｰ部分と の溝を合わせる",
"ﾚﾊﾞｰを下に下げ取付",
" と の取付向きに注意する",
"ｽｲｯﾁとﾌﾞﾚｰｶｰの向きを合わせること",
"OFF",
"ｽﾑｰｽﾞに動作する事",
"ON",
"目視で平行に組付け"
],
"Tolks": [
"締付ﾄﾙｸ 90cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"裏面",
"表面",
"検査表 :5.ﾒｲﾝSW(1)組立時調整確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "1.8N･m",
"WorkName": "ﾊｰﾈｽ接続(ｱｰｽﾌﾟﾚｰﾄ・ﾀｰﾐﾅﾙﾌﾞﾛｯｸ)",
"WorkItems": [],
"WorkPoints": [
"TERMINAL のｱｰｽﾏｰｸ刻印の向きに注意"
],
"Tolks": [
"締付ﾄﾙｸ 1.8N･m",
"締付ﾄﾙｸ 1.8N･m",
"締付ﾄﾙｸ 1.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表TERMINAL :ﾄﾙｸ計測(2)ｱｰｽﾌﾟﾚｰﾄ",
"検査表 :1.電源部(3)-2ﾈｼﾞ締めﾄﾙｸ確認",
"平行に取付",
"ｱｰｽﾏｰｸ",
"E7X001",
"E6X001",
"E5X001",
"E4X001",
"ｱｰｽﾏｰｸ",
"斜めに取付",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.8N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾒｰﾀ",
"Size": "No.2",
"ToolOther": "1.8N･m",
"WorkName": "ﾊｰﾈｽ接続(ｱｰｽﾌﾟﾚｰﾄ・ﾀｰﾐﾅﾙﾌﾞﾛｯｸ)",
"WorkItems": [
"■2. 検査表のﾁｪｯｸ方法に従ってﾄﾙｸ計測を実施する",
"■3. 1の完成品の配線を ﾒｲﾝﾀｰﾐﾅﾙに差込む",
"4. 3の完成品に を取付ける",
"■1. の配線をTERMINAL へSCREW で締結する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"L1 L1bX101",
"L2 L2bX101",
"L3 L3bX101",
"PE EX101",
"挿入向き凹凸",
"検査表 :1.電源部(2)-1ｽﾌﾟﾘﾝｸﾞ端子台の差込確認",
"■安全作業",
"WEPJ-G002-D09"
]
} | {
"QualityItem": "締付ﾄﾙｸ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "1.8N･m±10%",
"Method": "ﾄﾙｸﾒｰﾀ",
"RecordMethod": "WEPJ-G002-D09",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊｰﾈｽ接続(ｱｰｽﾌﾟﾚｰﾄ・ﾀｰﾐﾅﾙﾌﾞﾛｯｸ)",
"WorkItems": [
"■2. 検査表のﾁｪｯｸ方法に従ってﾄﾙｸ計測を実施する",
"■3. 1の完成品の配線を ﾒｲﾝﾀｰﾐﾅﾙに差込む",
"4. 3の完成品に を取付ける",
"■1. の配線をTERMINAL へSCREW で締結する"
],
"WorkPoints": [
"TERMINAL のｱｰｽﾏｰｸ刻印の向きに注意"
],
"Tolks": [
"締付ﾄﾙｸ 1.8N･m",
"締付ﾄﾙｸ 1.8N･m",
"締付ﾄﾙｸ 1.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"L1 L1bX101",
"L2 L2bX101",
"L3 L3bX101",
"PE EX101",
"挿入向き凹凸",
"検査表 :1.電源部(2)-1ｽﾌﾟﾘﾝｸﾞ端子台の差込確認",
"検査表TERMINAL :ﾄﾙｸ計測(2)ｱｰｽﾌﾟﾚｰﾄ",
"検査表 :1.電源部(3)-2ﾈｼﾞ締めﾄﾙｸ確認",
"平行に取付",
"ｱｰｽﾏｰｸ",
"E7X001",
"E6X001",
"E5X001",
"E4X001",
"ｱｰｽﾏｰｸ",
"斜めに取付",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀ組立",
"WorkItems": [],
"WorkPoints": [
"FM-2218",
"15㎜",
"取付方向注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｼｰﾙﾃｰﾌﾟを2周半巻く",
"付属ﾅｯﾄ",
"付属ﾌﾞﾗｹｯﾄ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "3.5N･m",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀ組立",
"WorkItems": [],
"WorkPoints": [
"FM-2218",
"15㎜",
"取付方向注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｼｰﾙﾃｰﾌﾟを2周半巻く",
"付属ﾅｯﾄ",
"付属ﾌﾞﾗｹｯﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾚｷﾞｭﾚｰﾀAC*締付治具",
"Size": "",
"ToolOther": "FM-2218",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀ組立",
"WorkItems": [
"1. REGULATOR のｺﾈｸﾀを取り外し､ﾎﾞﾙﾄとﾊﾟｯｷﾝも取り外す",
"2. COUPLER にｼｰﾙﾃｰﾌﾟを巻く",
"3. 1の完成品に2の完成品(ｶﾌﾟﾗ)を組付け､REGULATOR の付属ﾌﾞﾗｹｯﾄを付属ﾅｯﾄで締結する"
],
"WorkPoints": [
"ｺﾞﾑﾊﾟｯｷﾝ",
"ｺﾈｸﾀ",
"ﾎﾞﾙﾄ",
"K019-2",
"K019-3",
"FM-2218",
"巻き方向注意",
"15㎜",
"取付方向注意"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｼｰﾙﾃｰﾌﾟを2周半巻く",
"1~2山の掛かり代を残しｼｰﾙﾃｰﾌﾟを巻くこと",
"付属ﾅｯﾄ",
"付属ﾌﾞﾗｹｯﾄ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2218",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "60cN･m",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立①",
"WorkItems": [
"1. BRACKET にCONNECTOR CONNECTOR をBOLT WASHER で組付ける",
"2. 1の完成品にGROMMET とCONNECTOR を取付ける"
],
"WorkPoints": [
"切り欠きが右側になる事",
"各ｺﾈｸﾀの凸が2ｹある方が上になる事",
"2ｾｯﾄ製作",
"K020-1",
"K020-2",
"裏面噛み込み注意",
"CONNECTOR の爪がBRACKET に掛かる事"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります",
"裏面から挿入"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立①",
"WorkItems": [
"1. BRACKET にCONNECTOR CONNECTOR をBOLT WASHER で組付ける",
"2. 1の完成品にGROMMET とCONNECTOR を取付ける"
],
"WorkPoints": [
"切り欠きが右側になる事",
"各ｺﾈｸﾀの凸が2ｹある方が上になる事",
"2ｾｯﾄ製作",
"K020-1",
"K020-2",
"裏面噛み込み注意",
"CONNECTOR の爪がBRACKET に掛かる事"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります",
"裏面から挿入"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "60cN･m",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立②",
"WorkItems": [
"1. に をBOLT WASHER で組付け配線を裏から接続する"
],
"WorkPoints": [
"CNEXR",
"CNDUR",
"XR",
"CNLN",
"CNDUL",
"CNEXL",
"XL",
"切欠きを上に向けて組付け"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります",
"矢視A",
"矢視A"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立②",
"WorkItems": [
"1. に をBOLT WASHER で組付け配線を裏から接続する"
],
"WorkPoints": [
"CNEXR",
"CNDUR",
"XR",
"CNLN",
"CNDUL",
"CNEXL",
"XL",
"切欠きを上に向けて組付け"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります",
"矢視A",
"矢視A"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "EMGSW組付け",
"WorkItems": [
"3. 2.の完成品にSWITCH の付属ｶﾊﾞｰを取付ける",
"■1. SWITCH の型式を確認し製造番号(Lotの場合有)を検査書に記入する",
"■2. にSWITCH を組付ける"
],
"WorkPoints": [
"製造番号",
"型式",
"付属ｶﾊﾞｰ",
"確実に取付ける事 ※上から押さえ付けて取付",
"丸端子の取扱い注意",
"△印の向きに注意(21S､22S側)",
"ﾎﾞﾀﾝ部は取り外しH1工程前準備へ払い出す",
"下略図にて接続 ※ﾌﾛﾝﾄ､ﾘｱ用に注意",
"△印の向きに注意(11S､12S側)",
"確実に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 70cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表SWITCH :4.EMG SW(1)型式･検査書ﾁｪｯｸ",
"21S201",
"32S201",
"31S201",
"12S201",
"22S201",
"11S201",
"EMG SW : Front",
"EMG SW : Rear",
"21S202",
"32S202",
"31S202",
"22S202",
"11S202",
"12S202",
"検査表SWITCH :4.EMG SW(2)ﾈｼﾞ締めﾄﾙｸ",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "70cN･m",
"WorkName": "EMGSW組付け",
"WorkItems": [
"3. 2.の完成品にSWITCH の付属ｶﾊﾞｰを取付ける",
"■1. SWITCH の型式を確認し製造番号(Lotの場合有)を検査書に記入する",
"■2. にSWITCH を組付ける"
],
"WorkPoints": [
"製造番号",
"型式",
"付属ｶﾊﾞｰ",
"確実に取付ける事 ※上から押さえ付けて取付",
"丸端子の取扱い注意",
"△印の向きに注意(21S､22S側)",
"ﾎﾞﾀﾝ部は取り外しH1工程前準備へ払い出す",
"下略図にて接続 ※ﾌﾛﾝﾄ､ﾘｱ用に注意",
"△印の向きに注意(11S､12S側)",
"確実に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 70cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表SWITCH :4.EMG SW(1)型式･検査書ﾁｪｯｸ",
"21S201",
"32S201",
"31S201",
"12S201",
"22S201",
"11S201",
"EMG SW : Front",
"EMG SW : Rear",
"21S202",
"32S202",
"31S202",
"22S202",
"11S202",
"12S202",
"検査表SWITCH :4.EMG SW(2)ﾈｼﾞ締めﾄﾙｸ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "70cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "EMGSW組付け",
"WorkItems": [
"3. 2.の完成品にSWITCH の付属ｶﾊﾞｰを取付ける",
"■1. SWITCH の型式を確認し製造番号(Lotの場合有)を検査書に記入する",
"■2. にSWITCH を組付ける"
],
"WorkPoints": [
"製造番号",
"型式",
"付属ｶﾊﾞｰ",
"確実に取付ける事 ※上から押さえ付けて取付",
"丸端子の取扱い注意",
"△印の向きに注意(21S､22S側)",
"ﾎﾞﾀﾝ部は取り外しH1工程前準備へ払い出す",
"下略図にて接続 ※ﾌﾛﾝﾄ､ﾘｱ用に注意",
"△印の向きに注意(11S､12S側)",
"確実に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 70cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表SWITCH :4.EMG SW(1)型式･検査書ﾁｪｯｸ",
"21S201",
"32S201",
"31S201",
"12S201",
"22S201",
"11S201",
"EMG SW : Front",
"EMG SW : Rear",
"21S202",
"32S202",
"31S202",
"22S202",
"11S202",
"12S202",
"検査表SWITCH :4.EMG SW(2)ﾈｼﾞ締めﾄﾙｸ",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "50cN･m",
"WorkName": "ﾚｷﾞｭﾚｰﾀｺﾈｸﾀ組付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｷﾞｭﾚｰﾀｺﾈｸﾀ組付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "真空ﾎﾟﾝﾌﾟ前段取り",
"WorkItems": [
"■1. PUMP の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"2. PUMP に を取付ける"
],
"WorkPoints": [
"外箱に検査表有り",
"型式",
"30㎜",
"PUMP の付属ﾌｨﾙﾀｰをB2工程に払い出す",
"製造番号"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表PUMP :6.その他 (1)-5 型式･検査書ﾁｪｯｸ",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "真空ﾎﾟﾝﾌﾟ前段取り",
"WorkItems": [
"■1. PUMP の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"2. PUMP に を取付ける"
],
"WorkPoints": [
"外箱に検査表有り",
"型式",
"30㎜",
"PUMP の付属ﾌｨﾙﾀｰをB2工程に払い出す",
"製造番号"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表PUMP :6.その他 (1)-5 型式･検査書ﾁｪｯｸ",
"■安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送基板段取り",
"WorkItems": [
"■1. PCB-COM の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"2. PCB-COM の1つにCABLE を【CNB5】のｺﾈｸﾀに挿入し静電防止ｴｱｰﾏｯﾄで包みﾌﾛﾝﾄ_K323 / ﾘｱ_K324を表記する"
],
"WorkPoints": [
"K323⇒CABLE ｼｮｰﾄｺﾈｸﾀあり:1枚/K324⇒CABLE ｼｮｰﾄｺﾈｸﾀなし:1枚(ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様)",
"製造番号",
"型式"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表PCB-COM :3.基板関係(1)型式･検査書ﾁｪｯｸｰ3,4",
"K025A-1【ﾌﾛﾝﾄ用_K323】",
"K025-2 【ﾘｱ用_K324】",
"表記例",
"検査表PCB-COM :6.その他 (2)ｺﾈｸﾀ接続確認",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "検査表の有無を確認する事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送基板段取り",
"WorkItems": [
"■1. PCB-COM の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"2. PCB-COM の1つにCABLE を【CNB5】のｺﾈｸﾀに挿入し静電防止ｴｱｰﾏｯﾄで包みﾌﾛﾝﾄ_K323 / ﾘｱ_K324を表記する"
],
"WorkPoints": [
"K323⇒CABLE ｼｮｰﾄｺﾈｸﾀあり:1枚/K324⇒CABLE ｼｮｰﾄｺﾈｸﾀなし:1枚(ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様)",
"製造番号",
"型式"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表PCB-COM :3.基板関係(1)型式･検査書ﾁｪｯｸｰ3,4",
"K025A-1【ﾌﾛﾝﾄ用_K323】",
"K025-2 【ﾘｱ用_K324】",
"表記例",
"検査表PCB-COM :6.その他 (2)ｺﾈｸﾀ接続確認",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "I/O基板段取り",
"WorkItems": [
"■1. PCB-COM の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"2. 基板をｴｱｰﾏｯﾄで包み､ﾌﾛﾝﾄ_K321及びﾘｱ_K322を表記する"
],
"WorkPoints": [
"型式",
"製造番号"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"裏面",
"表面",
"K026-1",
"K026-2",
"検査表PCB-COM :3.基板関係(1)型式･検査書ﾁｪｯｸ-1,2",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "検査表の有無を確認する事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN前段取り",
"WorkItems": [
"■1. FAN FAN の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"2. FAN FAN のｺﾈｸﾀにﾀｸﾞ を取付ける"
],
"WorkPoints": [
"FAN 架台下用FANに【G111R】､FAN 真空ﾎﾟﾝﾌﾟ冷却用FANに【G112R】を取付ける",
"ﾀｸﾞの端面と保護ﾁｭｰﾌﾞの端面を合わせて固定",
"製造番号",
"型式",
"架台下用【G111R】",
"真空ﾎﾟﾝﾌﾟ冷却用【G112R】",
"製造番号",
"型式"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表FAN :6.その他(1)型式･検査書ﾁｪｯｸｰ3,4",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN前段取り",
"WorkItems": [
"■1. FAN FAN の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"2. FAN FAN のｺﾈｸﾀにﾀｸﾞ を取付ける"
],
"WorkPoints": [
"FAN 架台下用FANに【G111R】､FAN 真空ﾎﾟﾝﾌﾟ冷却用FANに【G112R】を取付ける",
"ﾀｸﾞの端面と保護ﾁｭｰﾌﾞの端面を合わせて固定",
"製造番号",
"型式",
"架台下用【G111R】",
"真空ﾎﾟﾝﾌﾟ冷却用【G112R】",
"製造番号",
"型式"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表FAN :6.その他(1)型式･検査書ﾁｪｯｸｰ3,4"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "架台下用FAN組立",
"WorkItems": [
"1. にFAN-GUARD をBOLT WASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"FLOW方向に注意する事",
"FLOW方向",
"FAN-GUARD FUN-GUARDの取付け方向注意"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台下用FAN組立",
"WorkItems": [
"1. にFAN-GUARD をBOLT WASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"FLOW方向に注意する事",
"FLOW方向",
"FAN-GUARD FUN-GUARDの取付け方向注意"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "78cN･m",
"WorkName": "真空ﾎﾟﾝﾌﾟ冷却用FAN組立",
"WorkItems": [
"1. にFAN-GUARD をBOLT WASHER WASHER NUT WASHER で取付ける",
"2 1完成品にPLATE FAN-FILTER をWASHER NUT WASHER WASHER WASHER で組付ける",
"1. にFAN-GUARD をBOLT WASHER WASHER NUT WASHER で取付ける",
"2 1完成品にPLATE FAN-FILTER をWASHER NUT WASHER WASHER WASHER で組付ける"
],
"WorkPoints": [
"･取付順番に注意する事･ の配線とFAN-GUARD の向き注意する事",
"取付順番に注意する事",
"FAN-GUARD の折り曲げ",
"PLATE の取付方向の詳細",
"･取付順番に注意する事･ の配線とFAN-GUARD の向き注意する事",
"取付順番に注意する事",
"FAN-GUARD の折り曲げ",
"PLATE の取付方向の詳細"
],
"Tolks": [
"締付ﾄﾙｸ 78cN･m",
"締付ﾄﾙｸ 78cN･m",
"締付ﾄﾙｸ 78cN･m",
"締付ﾄﾙｸ 78cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"裏面",
"表面",
"取付け方向に注意!PLATE の部品には方向性があります｡",
"広い",
"狭い",
"裏面",
"表面",
"裏面",
"表面",
"取付け方向に注意!PLATE の部品には方向性があります｡",
"広い",
"狭い",
"裏面",
"表面"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "78cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "真空ﾎﾟﾝﾌﾟ冷却用FAN組立",
"WorkItems": [
"1. にFAN-GUARD をBOLT WASHER WASHER NUT WASHER で取付ける",
"2 1完成品にPLATE FAN-FILTER をWASHER NUT WASHER WASHER WASHER で組付ける"
],
"WorkPoints": [
"･取付順番に注意する事･ の配線とFAN-GUARD の向き注意する事",
"取付順番に注意する事",
"FAN-GUARD の折り曲げ",
"穴ｱﾘ",
"穴ｱﾘ",
"穴ﾅｼ",
"穴ﾅｼ",
"穴ｱﾘ",
"穴ﾅｼ",
"PLATE の取付方向の詳細"
],
"Tolks": [
"締付ﾄﾙｸ 78cN･m",
"締付ﾄﾙｸ 78cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"裏面",
"表面",
"矢視A",
"矢視A",
"取付け方向に注意!PLATE の部品には方向性があります｡",
"広い",
"狭い",
"裏面",
"表面",
"広い",
"狭い",
"広い",
"穴有",
"狭い",
"広い"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "32㎜",
"ToolOther": "4N･m",
"WorkName": "ｹｰﾌﾞﾙｻﾎﾟｰﾄ組立",
"WorkItems": [
"1. PLATE にCABLE-SUPPORT を組付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 4N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "4N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "天板受けﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. BRACKET にSPACER をBOLT WASHER で組付ける"
],
"WorkPoints": [
"㉘にクランプさせて作業実施"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"※4ｾｯﾄ組立"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾞﾛﾒｯﾄ前準備",
"WorkItems": [
"1. GROMMET に切り込みを入れる"
],
"WorkPoints": [
"縦横切り込み長さ:35㎜~40㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"※4ｾｯﾄ製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "35~40㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立①",
"WorkItems": [
"1. PLATE PLATE にSCREW をNUT で組付ける",
"2. 1の完成品にSTOPPER を挿入する"
],
"WorkPoints": [
"ｽﾄｯﾊﾟｰの潰れ代を1㎜以上確保すること",
"SCREW の六角穴の向きに注意する",
"SCREW の六角穴の向きに注意する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"28.5㎜",
"30㎜",
"1.0~1.5㎜",
"組付け寸法"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立①",
"WorkItems": [
"1. PLATE PLATE にSCREW をNUT で組付ける",
"2. 1の完成品にSTOPPER を挿入する"
],
"WorkPoints": [
"ｽﾄｯﾊﾟｰの潰れ代を1㎜以上確保すること",
"SCREW の六角穴の向きに注意する",
"SCREW の六角穴の向きに注意する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"28.5㎜",
"30㎜",
"1.0~1.5㎜",
"組付け寸法"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立②",
"WorkItems": [
"1. にCLIP をBOLT で組付ける",
"2. にBRACKET をBOLT で組付ける",
"3. にSPACER をBOLT WASHER で組付ける"
],
"WorkPoints": [
"方向に注意",
"治具を挟み､押当てで組付け",
"表面 組付け時治具使用の事",
"FM-6437"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"押当て",
"裏面",
"表面",
"裏面",
"表面"
]
} | {
"QualityItem": "取付方向確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立②",
"WorkItems": [
"1. にCLIP をBOLT で組付ける",
"2. にBRACKET をBOLT で組付ける",
"3. にSPACER をBOLT WASHER で組付ける"
],
"WorkPoints": [
"治具を挟み､押当てで組付け",
"表面 組付け時治具使用の事",
"FM-6437"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"押当て"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸ｽﾄｯﾊﾟｰ位置決め調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6437",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立②",
"WorkItems": [
"1. にCLIP をBOLT で組付ける",
"2. にBRACKET をBOLT で組付ける",
"3. にSPACER をBOLT WASHER で組付ける"
],
"WorkPoints": [
"治具を挟み､押当てで組付け",
"表面 組付け時治具使用の事",
"FM-6437"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"押当て"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6437",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立②",
"WorkItems": [
"1. にCLIP をBOLT で組付ける",
"2. にBRACKET をBOLT で組付ける",
"3. にSPACER をBOLT WASHER で組付ける"
],
"WorkPoints": [
"治具を挟み､押当てで組付け",
"表面 組付け時治具使用の事",
"FM-6437"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"押当て"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立②",
"WorkItems": [
"1. にCLIP をBOLT で組付ける",
"2. にBRACKET をBOLT で組付ける",
"3. にSPACER をBOLT WASHER で組付ける"
],
"WorkPoints": [
"治具を挟み､押当てで組付け",
"表面 組付け時治具使用の事",
"FM-6437"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"押当て"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ACｻｰﾎﾞﾓｰﾀﾄﾞﾗｲﾊﾞｰ前準備",
"WorkItems": [
"■1. MOTOR-DRIVER MOTOR-DRIVER の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"3. 検査表の指示に従いMOTOR-DRIVER MOTOR-DRIVER のｱﾄﾞﾚｽ設定を行う",
"2. MOTOR-DRIVER MOTOR-DRIVER にフロント_FYM及びリア_RYMと㉗テープで表記する"
],
"WorkPoints": [
"型式",
"製造番号",
"表に基づきﾄﾞﾗｲﾊﾞｰに負荷名称を表記する",
"ｱﾄﾞﾚｽ設定表",
"必ず表記と合わせること",
"K035-1",
"K035-2",
"K035-3",
"K035-4",
"K035-5",
"K035-6"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"表記例",
"矢視A",
"矢視A",
"矢野B",
"検査表MOTOR-DRIVER :2.ﾄﾞﾗｲﾊﾞｰ設定(2)負荷設定確認",
"検査表MOTOR-DRIVER :2.ﾄﾞﾗｲﾊﾞｰ設定(1)型式･検査書ﾁｪｯｸ",
"ﾌﾛﾝﾄ",
"ﾘｱ",
"FYM",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ACｻｰﾎﾞﾓｰﾀﾄﾞﾗｲﾊﾞｰ前準備",
"WorkItems": [
"■1. MOTOR-DRIVER MOTOR-DRIVER の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"3. 検査表の指示に従いMOTOR-DRIVER MOTOR-DRIVER のｱﾄﾞﾚｽ設定を行う",
"2. MOTOR-DRIVER MOTOR-DRIVER にフロント_FYM及びリア_RYMと㉗テープで表記する"
],
"WorkPoints": [
"型式",
"製造番号",
"表に基づきﾄﾞﾗｲﾊﾞｰに負荷名称を表記する",
"ｱﾄﾞﾚｽ設定表",
"必ず表記と合わせること",
"K035-1",
"K035-2",
"K035-3",
"K035-4",
"K035-5",
"K035-6"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"表記例",
"矢視A",
"矢視A",
"矢野B",
"検査表MOTOR-DRIVER :2.ﾄﾞﾗｲﾊﾞｰ設定(2)負荷設定確認",
"検査表MOTOR-DRIVER :2.ﾄﾞﾗｲﾊﾞｰ設定(1)型式･検査書ﾁｪｯｸ",
"ﾌﾛﾝﾄ",
"ﾘｱ",
"FYM",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "194cN･m",
"WorkName": "X軸ﾄﾞﾗｲﾊﾞｰ前準備",
"WorkItems": [
"1. にBRACKET をSCREW で組付ける",
"2. にフロント_ＦＸ及びリア_ＲＸと㉘テープで表記する"
],
"WorkPoints": [
" K035-1_FX軸(ﾌﾛﾝﾄ):K036-1 K035-4_RX軸(ﾘｱ):K036-2"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"矢視A",
"矢視A",
"矢視B",
"矢視B",
"FX",
"RX"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPUBOX前準備",
"WorkItems": [
"■1. の製造番号を検査表に記入する",
"2. にBRACKET をBOLT WASHER で組付ける"
],
"WorkPoints": [
"この部分の番号を記入",
"CPU BOXの底面と面合わせ",
"BFG",
"UNI01※-BFG"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :6.その他 (1)型式･検査書ﾁｪｯｸｰ1",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.2N･m",
"WorkName": "CPUBOX前準備",
"WorkItems": [
"■1. の製造番号を検査表に記入する",
"2. にBRACKET をBOLT WASHER で組付ける"
],
"WorkPoints": [
"この部分の番号を記入",
"CPU BOXの底面と面合わせ",
"BFG",
"UNI01※-BFG"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :6.その他 (1)型式･検査書ﾁｪｯｸｰ1",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾏｸﾞﾈｯﾄｶﾊﾞｰ前段取り",
"WorkItems": [
"2. COVER へLABEL を貼付ける(左前､右奥)",
"1. COVER へLABEL を貼付ける(右前､左奥)",
"3. COVER へLABEL を貼付ける(左前)",
"4. COVER へLABEL を貼付ける(右奥)",
"2. COVER へLABEL を貼付ける(左前､右奥)",
"1. COVER へLABEL を貼付ける(右前､左奥)",
"3. COVER へLABEL を貼付ける(左前)",
"4. COVER へLABEL を貼付ける(右奥)",
"2. COVER へLABEL を貼付ける(左前､右奥)",
"1. COVER へLABEL を貼付ける(右前､左奥)",
"3. COVER へLABEL を貼付ける(左前)",
"4. COVER へLABEL を貼付ける(右奥)",
"2. COVER へLABEL を貼付ける(左前､右奥)",
"1. COVER へLABEL を貼付ける(右前､左奥)",
"3. COVER へLABEL を貼付ける(左前)",
"4. COVER へLABEL を貼付ける(右奥)"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"貼付け面に注意!この部品には方向性があります｡",
"下面合わせ",
"200mm",
"貼付け面に注意!この部品には方向性があります｡",
"下面合わせ",
"200mm",
"貼付け面に注意!この部品には方向性があります｡",
"下面合わせ",
"200mm",
"貼付け面に注意!この部品には方向性があります｡",
"下面合わせ",
"200mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "CPUBOX(P10A)取付用ﾌﾞﾗｹｯﾄ前準備",
"WorkItems": [
"1. BRACKET にCOVER を指定長さにｶｯﾄして取付ける"
],
"WorkPoints": [
"ｶｯﾄ寸法:40㎜×2本",
"外側の端面に合わせて貼付ける",
"外側の端面に合わせて貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPUBOX(P10A)取付用ﾌﾞﾗｹｯﾄ前準備",
"WorkItems": [
"1. BRACKET にCOVER を指定長さにｶｯﾄして取付ける"
],
"WorkPoints": [
"ｶｯﾄ寸法:40㎜×2本",
"外側の端面に合わせて貼付ける",
"外側の端面に合わせて貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "50cN･m",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"1. BRACKET にVALVE をBOLT WASHER WASHER でVALVE をBOLT WASHER で組付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 55cN･m",
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"仕様により組立数が違います｡ ﾘｱ側台車仕様時:2ｾｯﾄ組立 ﾘｱ側ﾄﾚｲ仕様時:1ｾｯﾄ組立"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "55cN･m",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"2. TUBE を指定長さにｶｯﾄして1の完成品に取付ける"
],
"WorkPoints": [
"ｶｯﾄ寸法:240㎜×2本",
"WASHER AWを間に挟む",
"ﾎﾟｰﾄ4",
"ﾎﾟｰﾄ2(白ﾗｲﾝ)",
"VALVE の取付方向注意(矢印▲)",
"BRACKET VALVE "
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "55cN･m±5%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"2. TUBE を指定長さにｶｯﾄして1の完成品に取付ける"
],
"WorkPoints": [
"ｶｯﾄ寸法:240㎜×2本",
"WASHER AWを間に挟む",
"ﾎﾟｰﾄ4",
"ﾎﾟｰﾄ2(白ﾗｲﾝ)",
"VALVE の取付方向注意(矢印▲)",
"BRACKET VALVE "
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事指示寸法±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｶｯﾀｰﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"1. BRACKET にVALVE をBOLT WASHER で組付けJOINT を挿入する",
"2. TUBE を指定長さにｶｯﾄして1の完成品に取付けﾌﾛﾝﾄ､ﾘｱに分けて配管に番号を記載する",
"3. 指定長さにｶｯﾄした2完成品を下図のように接続する事"
],
"WorkPoints": [
"配管端より50㎜に配管番号を記入する事･配管Φ6 黒 ⇒ 黄色ﾏｰｶｰで記入･ﾌﾛﾝﾄ､ﾘｱを識別する事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"※2ｾｯﾄ組立"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ｶｯﾀｰﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"1. BRACKET にVALVE をBOLT WASHER で組付けJOINT を挿入する",
"2. TUBE を指定長さにｶｯﾄして1の完成品に取付けﾌﾛﾝﾄ､ﾘｱに分けて配管に番号を記載する",
"3. 指定長さにｶｯﾄした2完成品を下図のように接続する事"
],
"WorkPoints": [
"配管端より50㎜に配管番号を記入する事･配管Φ6 黒 ⇒ 黄色ﾏｰｶｰで記入･ﾌﾛﾝﾄ､ﾘｱを識別する事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"※2ｾｯﾄ組立"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事指示寸法±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾘﾆｱｶﾞｲﾄﾞ前準備",
"WorkItems": [
"2. LINEAR-WAY にJOINT を組付ける",
"1. LINEAR-WAY ﾘﾆｱｶﾞｲﾄﾞの防錆油をｳｴｽで拭き取り錆や傷を確認する"
],
"WorkPoints": [
"･JOINT を手で軽く締め止まったところ(着座)から45度締付ける｡･締めすぎに注意し向きを合わせる｡",
"ｽﾗｲﾀﾞｰを移動させてﾚｰﾙ全体の防錆油を拭き取る"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"刻印 : YKL 123456",
"ｽﾗｲﾀﾞｰ移動"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "加工面に打痕､傷等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒｲﾝ配管前準備",
"WorkItems": [
"1. COUPLER にHOSE を接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"削除"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "N･m",
"WorkName": "ｺﾈｸﾀ接続部組立【OP:ﾄﾚｲ仕様】",
"WorkItems": [],
"WorkPoints": [
"ｺﾈｸﾀの向きに注意"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品確認①",
"WorkItems": [
"1. ﾗｲｾﾝｽｼｰﾙ SOFTWARE-LICENSE SOFTWARE-LICENSE SOFTWARE-LICENSE SOFTWARE-LICENSE をB1工程へ払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"削除"
]
} | {
"QualityItem": "ｽﾙｰ部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り払い出されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品確認②",
"WorkItems": [
"1. Y軸ﾓｰﾀﾄﾞﾗｲﾊﾞｰ渡り配線 CABLE をB1工程へ払い出す",
"2. Y軸ﾄﾞﾗｲﾊﾞｰ用ﾌﾞﾗｹｯﾄBRACKET をB1工程に払い出す",
"3. ﾄﾚｲ仕様の場合CABLE CABLE をB1工程に払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "ｽﾙｰ部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り払い出されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品確認③",
"WorkItems": [
"1. RAIL ﾚｰﾙ､TERMINAL-SUPPORT ﾀｰﾐﾅﾙｻﾎﾟｰﾄ､TERMINAL-BLOCK 端子台をB1工程へ払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "ｽﾙｰ部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り払い出されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品確認④",
"WorkItems": [
"1. BRACKET BRACKET ﾌﾞﾗｹｯﾄ をB1工程へ払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "ｽﾙｰ部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り払い出されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品確認⑤",
"WorkItems": [
"1. ｽﾍﾟｰｻｰ SPACER SPACER SPACER をB1工程へ払い出す"
],
"WorkPoints": [
"SPACER :I/O基板､搬送基板用SPACER :DC電源用SPACER :真空ﾎﾟﾝﾌﾟ用"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "ｽﾙｰ部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り払い出されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品確認⑥",
"WorkItems": [
"1. ﾌｧﾝｶﾞｰﾄﾞ FAN-GUARD FAN-GUARD をB1工程へ払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "ｽﾙｰ部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り払い出されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品確認⑦",
"WorkItems": [
"1. ﾗﾍﾞﾙ LABEL LABEL LABEL LABEL LABEL を各工程へ払い出す事"
],
"WorkPoints": [
"LABEL の銘板ﾗﾍﾞﾙは下記部分のみを払い出す",
"LABEL の【CX2R】は不要の為廃棄する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"LABEL の橙色枠内の銘板ﾗﾍﾞﾙをB1工程へ払い出す",
"LABEL の水色枠内の銘板ﾗﾍﾞﾙをH1工程前準備へ払い出す",
"LABEL の紫色枠内の銘板ﾗﾍﾞﾙをB2工程前準備へ払い出す"
]
} | {
"QualityItem": "ｽﾙｰ部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り払い出されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品確認⑧",
"WorkItems": [
"1. その他残部品 CLIP COVER SCREW CABLE-SUPPORT CABLE-SUPPORT SPACER をB1工程へ払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "ｽﾙｰ部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り払い出されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾝﾀﾞｸﾀﾝｽﾊﾞﾙﾌﾞ初期設定",
"WorkItems": [
"1. VALVE 型式確認とｼﾘｱﾙNo.を記入する",
"2. VALVE のｱﾄﾞﾚｽSW､通信速度SWを設定する"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙNo.",
"MSD:1 LSD:1",
"500kB"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表VALVE :型式番号確認",
"検査表VALVE :接続ﾁｪｯｸとｽｲｯﾁ設定",
"NGMR627-G11-024"
]
} | {
"QualityItem": "型式確認ｼﾘｱﾙNo.記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "NGMR627-G11-024",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾝﾀﾞｸﾀﾝｽﾊﾞﾙﾌﾞ初期設定",
"WorkItems": [
"1. VALVE 型式確認とｼﾘｱﾙNo.を記入する",
"2. VALVE のｱﾄﾞﾚｽSW､通信速度SWを設定する"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙNo.",
"MSD:1 LSD:1",
"500kB"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表VALVE :型式番号確認",
"検査表VALVE :接続ﾁｪｯｸとｽｲｯﾁ設定",
"NGMR627-G11-013"
]
} | {
"QualityItem": "接続設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続設定出来ている事",
"Method": "目視",
"RecordMethod": "NGMR627-G11-013",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾝﾀﾞｸﾀﾝｽﾊﾞﾙﾌﾞ配管",
"WorkItems": [
"1. にPIPE PIPE をJOINT RING で取付ける"
],
"WorkPoints": [
"下図の向きで取付け",
"ﾊﾞﾙﾌﾞ ､ﾊﾟｲﾌﾟPIPE PIPE ､ﾘﾝｸﾞRING との接続面はｱﾙｺｰﾙで拭き上げた後に接続する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ﾊﾞﾙﾌﾞ取付方向確認",
"NGMR627-G11-024"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "NGMR627-G11-024",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｽﾄｯﾊﾟﾎﾞﾙﾄ組立",
"WorkItems": [
"1. SPACER にBOLT を仮止めする"
],
"WorkPoints": [
"4ｾｯﾄ組立",
"本締め:SD-EFP3A11-028(H1工程ﾒｶﾄﾞｯｷﾝｸﾞ)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "16.5±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ取付(USB2K351/USB3K351)",
"WorkItems": [
"1. CABLE のCABLEにLABEL の USB2K351･USB3K351･RoHS のﾀｸﾞを指定の位置に取付ける"
],
"WorkPoints": [
"USB2K351-USB1",
"USB3K351-USB2",
"USBﾏｰｸの反対側に取付け",
"USB2K351-USB1",
"USB3K351-USB2"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ取付(USB4)",
"WorkItems": [
"1. CONVERTER のCABLEに LABEL のUSB4P.RoHS のﾀｸﾞを指定の位置に取付ける"
],
"WorkPoints": [
"ﾀｸﾞ取付位置に注意",
"USB4K351-USB4P",
"USB4K351",
"RoHS",
"RoHS",
"USB4P"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ取付(LAN1K351)",
"WorkItems": [
"1. CABLE のCABLEに LABEL のLAN1K351 のﾀｸﾞを指定の位置に取付ける"
],
"WorkPoints": [
"ﾀｸﾞ取付位置は下の写真を参照"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ取付(LAN1R)",
"WorkItems": [
"1. CONNECTOR にLABEL ﾀｸﾞﾗﾍﾞﾙを指定の位置に貼付ける"
],
"WorkPoints": [
"貼付位置は下の写真を参照",
"ﾀｸﾞがｺﾈｸﾀから脱落しやすいので､LABEL ｼｰﾙを剥がし､CONNECTOR ｺﾈｸﾀにｼｰﾙを直接貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ取付(ｼｸﾞﾅﾙﾀﾜｰ)",
"WorkItems": [
"1. SIGNAL-TOWER ｼｸﾞﾅﾙﾀﾜｰのCABLEに LABEL のB201R のﾀｸﾞを指定の位置に取付ける"
],
"WorkPoints": [
"黒ﾁｭｰﾌﾞの端とﾀｸﾞの端を合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ取付(LAN1A2000(OP))",
"WorkItems": [
"1. CABLE CABLEにLABEL ﾀｸﾞを指定の位置に取付ける"
],
"WorkPoints": [
"ﾀｸﾞ取付位置は下の写真を参照",
"※EFEM連結仕様の場合"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃﾞﾊﾞｲｽﾈｯﾄ設定",
"WorkItems": [
"■1. INTERFACE-UNIT INTERFACE-UNIT の型式を確認し､ｼﾘｱﾙNo.を検査表に転記する",
"2. INTERFACE-UNIT INTERFACE-UNIT のﾛｰﾀﾘｰｽｲｯﾁでｱﾄﾞﾚｽ設定を行う"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙNo.",
"型式",
"ｼﾘｱﾙNo.",
"ｱﾄﾞﾚｽ設定:06",
"ｱﾄﾞﾚｽ設定:08",
"K302",
"K301"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表INTERFACE-UNIT :型式･検査書ﾁｪｯｸ",
"検査表INTERFACE-UNIT :接続ﾁｪｯｸとｽｲｯﾁ設定",
"検査表INTERFACE-UNIT :接続ﾁｪｯｸとｽｲｯﾁ設定",
"NGMR627-G11-009"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "NGMR627-G11-009",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃﾞﾊﾞｲｽﾈｯﾄ設定",
"WorkItems": [
"■1. INTERFACE-UNIT INTERFACE-UNIT の型式を確認し､ｼﾘｱﾙNo.を検査表に転記する",
"2. INTERFACE-UNIT INTERFACE-UNIT のﾛｰﾀﾘｰｽｲｯﾁでｱﾄﾞﾚｽ設定を行う"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙNo.",
"型式",
"ｼﾘｱﾙNo.",
"ｱﾄﾞﾚｽ設定:06",
"ｱﾄﾞﾚｽ設定:08",
"K302",
"K301"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表INTERFACE-UNIT :型式･検査書ﾁｪｯｸ",
"検査表INTERFACE-UNIT :接続ﾁｪｯｸとｽｲｯﾁ設定",
"検査表INTERFACE-UNIT :接続ﾁｪｯｸとｽｲｯﾁ設定",
"NGMR627-G11-009"
]
} | {
"QualityItem": "接続設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続設定出来ている事",
"Method": "目視",
"RecordMethod": "NGMR627-G11-009",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃﾞﾊﾞｲｽﾈｯﾄ中継分岐設定",
"WorkItems": [
"■1. TERMINAL-BLOCK TERMINAL-BLOCK の型式を確認し､ﾛｯﾄNo.を検査表に転記する",
"2. TERMINAL-BLOCK TERMINAL-BLOCK の終端抵抗DIP SWを設定する"
],
"WorkPoints": [
"終端抵抗DIP SWONに設定のこと",
"終端抵抗DIP SWOFFに設定のこと",
"ﾛｯﾄNo.",
"ﾛｯﾄNo.",
"X104",
"X102",
"X103",
"型式:DCN1-3NC",
"型式:DCN1-1NC",
"DIP SW設定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表TERMINAL-BLOCK :型式･検査書ﾁｪｯｸ",
"検査表TERMINAL-BLOCK :ｺﾈｸﾀ接続ﾁｪｯｸ",
"ON",
"OFF",
"ON",
"OFF",
"NGMR627-G11-009"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "NGMR627-G11-009",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃﾞﾊﾞｲｽﾈｯﾄ中継分岐設定",
"WorkItems": [
"■1. TERMINAL-BLOCK TERMINAL-BLOCK の型式を確認し､ﾛｯﾄNo.を検査表に転記する",
"2. TERMINAL-BLOCK TERMINAL-BLOCK の終端抵抗DIP SWを設定する"
],
"WorkPoints": [
"終端抵抗DIP SWONに設定のこと",
"終端抵抗DIP SWOFFに設定のこと",
"ﾛｯﾄNo.",
"ﾛｯﾄNo.",
"X104",
"X102",
"X103",
"型式:DCN1-3NC",
"型式:DCN1-1NC",
"DIP SW設定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表TERMINAL-BLOCK :型式･検査書ﾁｪｯｸ",
"検査表TERMINAL-BLOCK :ｺﾈｸﾀ接続ﾁｪｯｸ",
"ON",
"OFF",
"ON",
"OFF",
"NGMR627-G11-009"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "NGMR627-G11-009",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾈｸﾀ配線(MFC1/X104-2)",
"WorkItems": [
"1. CABLE CABLE端子を ｺﾈｸﾀに接続する"
],
"WorkPoints": [
"MFC1",
" N026 TERMINAL-BLOCK付属ｺﾈｸﾀ",
"V- 棒端子 黒色",
"CAN L 棒端子 青色",
"DRAIN 棒端子 無印",
"CAN H 棒端子 白色",
"V+ 棒端子 赤色",
"棒端子の凹凸部分を内側に向け､解除ﾎﾞﾀﾝ(ｵﾚﾝｼﾞ)を押して挿し込む",
"ｶﾞｽ供給部(Ar)配線時(標準仕様)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表CABLE :ｺﾈｸﾀ接続ﾁｪｯｸ",
"NGMR627-G11-009"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "NGMR627-G11-009",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾈｸﾀ配線(MFC2/X104-3)",
"WorkItems": [
"1. CABLE CABLE端子を ｺﾈｸﾀに接続する"
],
"WorkPoints": [
"MFC2",
" N026 TERMINAL-BLOCK付属ｺﾈｸﾀ",
"V- 棒端子 黒色",
"CAN L 棒端子 青色",
"DRAIN 棒端子 無印",
"CAN H 棒端子 白色",
"V+ 棒端子 赤色",
"棒端子の凹凸部分を内側に向け､解除ﾎﾞﾀﾝ(ｵﾚﾝｼﾞ)を押して挿し込む",
"ｶﾞｽ供給部(O2)配線時(ｵﾌﾟｼｮﾝ仕様)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表CABLE :ｺﾈｸﾀ接続ﾁｪｯｸ",
"NGMR627-G11-009"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "NGMR627-G11-009",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "型式確認(ｺﾝﾌﾟﾗｲｱﾝｽ)",
"WorkItems": [
"■1. MONITOR の型式確認を行い､ｼﾘｱﾙNo.を検査表に転記する",
"■2. REMOVABLE-MEMORY REMOVABLE-MEMORY の型式確認を行う"
],
"WorkPoints": [
"背面",
"型式",
"ｼﾘｱﾙNo.",
"型式",
"型式"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表MONITOR :設備組付け前に確認する部品",
"検査表MONITOR :設備組付け前に確認する部品",
"SFU32048E1AE1TO-I-QT-1A1-STD",
"SSD-032G201AT",
"NGMR627-G11-011"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "NGMR627-G11-011",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "型式確認(CONTROLUNIT)",
"WorkItems": [
"■1. および付属の検査書を確認し､ｼﾘｱﾙNo.を検査表に転記する"
],
"WorkPoints": [
"ｼﾘｱﾙNo."
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :型式･検査書ﾁｪｯｸ",
"NGMR627-G11-009"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "NGMR627-G11-009",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CFｶｰﾄﾞ取付け",
"WorkItems": [
"1. ｺﾝﾄﾛｰﾙﾕﾆｯﾄのCFｶｰﾄﾞｽﾛｯﾄに を挿し込む"
],
"WorkPoints": [
" 挿し込み後､ｶﾊﾞｰを締め青ﾏｰｷﾝｸﾞする",
"CFｶｰﾄﾞｽﾛｯﾄｶﾊﾞｰを外し､ を挿し込む",
" CFｶｰﾄﾞの方向に注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｭｰﾄｺﾈｸﾀ接続(PCN10/PCN30)",
"WorkItems": [
"1. ｺﾝﾄﾛｰﾙﾕﾆｯﾄにCABLE および付属ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"PCN30:ｺﾝﾄﾛｰﾙﾕﾆｯﾄ付属品",
"CABLE PCN10:ﾛｰﾀﾞｰ/ｱﾝﾛｰﾀﾞ(予約)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :ｺﾈｸﾀ接続ﾁｪｯｸ",
"NGMR627-G11-009"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "NGMR627-G11-009",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾟﾗｽﾞﾏﾓﾆﾀﾎﾞｰﾄﾞ取付(OP)",
"WorkItems": [
"■★1. PCB-COM の型式確認し､ｼﾘｱﾙNo.を検査表に転記する",
"★2. にPCB-COM を挿し込み付属ねじで固定する"
],
"WorkPoints": [
"ｼﾘｱﾙNo.",
"型式",
"CONTROL UNIT"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :型式･検査書ﾁｪｯｸ",
"NGMR627-G11-009"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "NGMR627-G11-009",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾟﾗｽﾞﾏﾓﾆﾀﾎﾞｰﾄﾞ取付(OP)",
"WorkItems": [
"■★1. PCB-COM の型式確認し､ｼﾘｱﾙNo.を検査表に転記する",
"★2. にPCB-COM を挿し込み付属ねじで固定する"
],
"WorkPoints": [
"ｼﾘｱﾙNo.",
"型式",
"CONTROL UNIT"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表 :型式･検査書ﾁｪｯｸ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "型式確認(ﾄﾗﾝｽ)",
"WorkItems": [
"■1. TRANSFORMER の型式を確認し､ｼﾘｱﾙNo.を検査表に転記する"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙNo.",
"付属の検査表"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表TRANSFORMER :型式･検査書ﾁｪｯｸ",
"NGMR627-G11-009"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "NGMR627-G11-009",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "型式確認(RF電源)",
"WorkItems": [
"■1. POWER-SUPPLY の型式を確認し､ｼﾘｱﾙNo.を検査表に転記する"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙNo.",
"付属の検査表"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表POWER-SUPPLY :型式･検査書ﾁｪｯｸ",
"NGMR627-G11-009"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "NGMR627-G11-009",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "型式確認(非常停止SW)",
"WorkItems": [
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNo.を検査表に転記する"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙNo."
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表SWITCH :型式･検査書ﾁｪｯｸ",
"NGMR627-G11-009"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "NGMR627-G11-009",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "型式確認(ﾌﾞﾚｰｶ・ｽｲｯﾁ)",
"WorkItems": [
"■1. BREAKER の型式を確認し､ｼﾘｱﾙNo.を検査表に転記する",
"■2. SWITCH-PARTS の型式を確認し､ｼﾘｱﾙNo.を検査表に転記する"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙNo.",
"型式",
"ｼﾘｱﾙNo."
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表BREAKER :型式･検査書ﾁｪｯｸ",
"検査表BREAKER :型式･検査書ﾁｪｯｸ",
"NGMR627-G11-009"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "NGMR627-G11-009",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "型式確認(SK)",
"WorkItems": [
"■1. SK の型式を確認し､ｼﾘｱﾙNo.を検査表に転記する"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙNo."
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表SK :型式･検査書ﾁｪｯｸ",
"NGMR627-G11-009"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "NGMR627-G11-009",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒｲﾝSW組立①",
"WorkItems": [
"1. BRACKET にCABLE-SUPPORT を取付ける(2ヶ)",
"4. 3.完成品にTERMINAL をBOLT WASHER で取付ける",
"2. BUSH を指定寸法にｶｯﾄし､BRACKET に取付ける",
"3. 2完成品にLABEL LABEL を貼付ける"
],
"WorkPoints": [
"BUSH L=60㎜",
"7㎜",
"F101",
"PE",
"L1",
"L2"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表BRACKET :接続ﾁｪｯｸ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.