input stringclasses 1 value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞｱ取付け(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"1. D-pinとﾌﾚｰﾑに隙間が無い事を確認しBOLT WASHER ･BOLT WASHER ･WASHER BOLT で固定する",
"2. ｺﾝﾍﾞｱ移載用治具を取り外す"
],
"WorkPoints": [
"治具取り外し後固定する",
"ﾘﾆｱｽｹｰﾙ等の干渉に注意する事"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-A01",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞｱ取付け(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"1. D-pinとﾌﾚｰﾑに隙間が無い事を確認しBOLT WASHER ･BOLT WASHER ･WASHER BOLT で固定する",
"2. ｺﾝﾍﾞｱ移載用治具を取り外す"
],
"WorkPoints": [
"治具取り外し後固定する",
"ﾘﾆｱｽｹｰﾙ等の干渉に注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WEAV-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱ移載用治具",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞｱ取付け(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"1. D-pinとﾌﾚｰﾑに隙間が無い事を確認しBOLT WASHER ･BOLT WASHER ･WASHER BOLT で固定する",
"2. ｺﾝﾍﾞｱ移載用治具を取り外す"
],
"WorkPoints": [
"治具取り外し後固定する",
"ﾘﾆｱｽｹｰﾙ等の干渉に注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞｱ取付け(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"1. D-pinとﾌﾚｰﾑに隙間が無い事を確認しBOLT WASHER ･BOLT WASHER ･WASHER BOLT で固定する",
"2. ｺﾝﾍﾞｱ移載用治具を取り外す"
],
"WorkPoints": [
"治具取り外し後固定する",
"ﾘﾆｱｽｹｰﾙ等の干渉に注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞｱ取付け(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"1. D-pinとﾌﾚｰﾑに隙間が無い事を確認しBOLT WASHER ･BOLT WASHER ･WASHER BOLT で固定する",
"2. ｺﾝﾍﾞｱ移載用治具を取り外す"
],
"WorkPoints": [
"治具取り外し後固定する",
"ﾘﾆｱｽｹｰﾙ等の干渉に注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WEAV-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱ移載用治具",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞｱ取付け(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"1. D-pinとﾌﾚｰﾑに隙間が無い事を確認しBOLT WASHER ･BOLT WASHER ･WASHER BOLT で固定する",
"2. ｺﾝﾍﾞｱ移載用治具を取り外す"
],
"WorkPoints": [
"治具取り外し後固定する",
"ﾘﾆｱｽｹｰﾙ等の干渉に注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "基板ﾎﾙﾀﾞ(ﾃﾞｭｱﾙ)搭載・取付け(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様、下受けﾋﾟﾝ一括交換式仕様、下受けﾋﾟﾝ自動交換式仕様あり)",
"WorkItems": [
"◆1. ①に㉘を取付け、架台に搭載する",
"2. 全てのﾎﾙﾀﾞを搭載後､指定箇所の隙間が無いことを確認しBOLT WASHER で固定する",
"◆1. ①に㉘を取付け、架台に搭載する",
"2. 全てのﾎﾙﾀﾞを搭載後､指定箇所の隙間が無いことを確認しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｺﾈｸﾀ名称を確認後取付ける事",
"ﾋﾟﾝ･架台当付け:0.03㎜以内",
"ｺﾈｸﾀ名称を確認後取付ける事",
"ﾋﾟﾝ･架台当付け:0.03㎜以内"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WEAV-G002-A01",
"InspectionItems": [
"検査表①:3.基板ﾎﾙﾀﾞﾕﾆｯﾄの取付",
"検査表①:3.基板ﾎﾙﾀﾞﾕﾆｯﾄの取付"
],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾎﾙﾀﾞ運搬治具",
"Size": "",
"ToolOther": "FM-4489",
"WorkName": "基板ﾎﾙﾀﾞ(ﾃﾞｭｱﾙ)搭載・取付け(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様、下受けﾋﾟﾝ一括交換式仕様、下受けﾋﾟﾝ自動交換式仕様あり)",
"WorkItems": [
"◆1. ①に㉘を取付け、架台に搭載する",
"2. 全てのﾎﾙﾀﾞを搭載後､指定箇所の隙間が無いことを確認しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｺﾈｸﾀ名称を確認後取付ける事",
"ﾋﾟﾝ･架台当付け:0.03㎜以内"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:3.基板ﾎﾙﾀﾞﾕﾆｯﾄの取付",
"◆作業者安全作業"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4489",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取り扱い",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞ(ﾃﾞｭｱﾙ)搭載・取付け(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様、下受けﾋﾟﾝ一括交換式仕様、下受けﾋﾟﾝ自動交換式仕様あり)",
"WorkItems": [
"◆1. ①に㉘を取付け、架台に搭載する",
"2. 全てのﾎﾙﾀﾞを搭載後､指定箇所の隙間が無いことを確認しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｺﾈｸﾀ名称を確認後取付ける事",
"ﾋﾟﾝ･架台当付け:0.03㎜以内"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:3.基板ﾎﾙﾀﾞﾕﾆｯﾄの取付",
"◆作業者安全作業",
"WEAV-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "基板ﾎﾙﾀﾞ(ﾃﾞｭｱﾙ)搭載・取付け(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様、下受けﾋﾟﾝ一括交換式仕様、下受けﾋﾟﾝ自動交換式仕様あり)",
"WorkItems": [
"◆1. ①に㉘を取付け、架台に搭載する",
"2. 全てのﾎﾙﾀﾞを搭載後､指定箇所の隙間が無いことを確認しBOLT WASHER で固定する",
"◆1. ①に㉘を取付け、架台に搭載する",
"2. 全てのﾎﾙﾀﾞを搭載後､指定箇所の隙間が無いことを確認しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｺﾈｸﾀ名称を確認後取付ける事",
"ﾋﾟﾝ･架台当付け:0.03㎜以内",
"ｺﾈｸﾀ名称を確認後取付ける事",
"ﾋﾟﾝ･架台当付け:0.03㎜以内"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:3.基板ﾎﾙﾀﾞﾕﾆｯﾄの取付",
"◆作業者安全作業",
"検査表①:3.基板ﾎﾙﾀﾞﾕﾆｯﾄの取付"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾎﾙﾀﾞ運搬治具",
"Size": "",
"ToolOther": "FM-4489",
"WorkName": "基板ﾎﾙﾀﾞ(ﾃﾞｭｱﾙ)搭載・取付け(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様、下受けﾋﾟﾝ一括交換式仕様、下受けﾋﾟﾝ自動交換式仕様あり)",
"WorkItems": [
"◆1. ①に㉘を取付け、架台に搭載する",
"2. 全てのﾎﾙﾀﾞを搭載後､指定箇所の隙間が無いことを確認しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｺﾈｸﾀ名称を確認後取付ける事",
"ﾋﾟﾝ･架台当付け:0.03㎜以内"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:3.基板ﾎﾙﾀﾞﾕﾆｯﾄの取付",
"◆作業者安全作業"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4489",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取り扱い",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞ(ﾃﾞｭｱﾙ)搭載・取付け(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様、下受けﾋﾟﾝ一括交換式仕様、下受けﾋﾟﾝ自動交換式仕様あり)",
"WorkItems": [
"◆1. ①に㉘を取付け、架台に搭載する",
"2. 全てのﾎﾙﾀﾞを搭載後､指定箇所の隙間が無いことを確認しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｺﾈｸﾀ名称を確認後取付ける事",
"ﾋﾟﾝ･架台当付け:0.03㎜以内"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:3.基板ﾎﾙﾀﾞﾕﾆｯﾄの取付",
"◆作業者安全作業",
"WEAV-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱ移載用治具",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞｱ搭載(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"◆2. ﾘﾌﾀｰでｺﾝﾍﾞｱを持ち上げる",
"1. ①の可動側搬送ﾚｰﾙを最大まで寄せておく",
"◆3. ｺﾝﾍﾞｱを架台に搭載する"
],
"WorkPoints": [
"ｺﾝﾍﾞｱ･配線への干渉に注意する事",
"ｺﾝﾍﾞｱへの干渉に注意する事",
"ｺﾝﾍﾞｱ搭載方向"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取り扱い",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ用ｱﾀｯﾁﾒﾝﾄ治具",
"Size": "",
"ToolOther": "FM-3221",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞｱ搭載(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"◆2. ﾘﾌﾀｰでｺﾝﾍﾞｱを持ち上げる",
"1. ①の可動側搬送ﾚｰﾙを最大まで寄せておく",
"◆3. ｺﾝﾍﾞｱを架台に搭載する"
],
"WorkPoints": [
"ｺﾝﾍﾞｱ･配線への干渉に注意する事",
"ｺﾝﾍﾞｱへの干渉に注意する事",
"ｺﾝﾍﾞｱ搭載方向"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-3221",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取り扱い",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱ移載用治具",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞｱ搭載(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"◆2. ﾘﾌﾀｰでｺﾝﾍﾞｱを持ち上げる",
"1. ①の可動側搬送ﾚｰﾙを最大まで寄せておく",
"◆3. ｺﾝﾍﾞｱを架台に搭載する"
],
"WorkPoints": [
"ｺﾝﾍﾞｱ･配線への干渉に注意する事",
"ｺﾝﾍﾞｱへの干渉に注意する事",
"ｺﾝﾍﾞｱ搭載方向"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取り扱い",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ用ｱﾀｯﾁﾒﾝﾄ治具",
"Size": "",
"ToolOther": "FM-3221",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞｱ搭載(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"◆2. ﾘﾌﾀｰでｺﾝﾍﾞｱを持ち上げる",
"1. ①の可動側搬送ﾚｰﾙを最大まで寄せておく",
"◆3. ｺﾝﾍﾞｱを架台に搭載する"
],
"WorkPoints": [
"ｺﾝﾍﾞｱ･配線への干渉に注意する事",
"ｺﾝﾍﾞｱへの干渉に注意する事",
"ｺﾝﾍﾞｱ搭載方向"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-3221",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取り扱い",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞｱ取付け(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"2. ｺﾝﾍﾞｱ移載用治具を取り外す"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙ等の干渉に注意する事",
"治具取り外し後固定する"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-A01",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞｱ取付け(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"2. ｺﾝﾍﾞｱ移載用治具を取り外す"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙ等の干渉に注意する事",
"治具取り外し後固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WEAV-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱ移載用治具",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞｱ取付け(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"2. ｺﾝﾍﾞｱ移載用治具を取り外す",
"2. ｺﾝﾍﾞｱ移載用治具を取り外す"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙ等の干渉に注意する事",
"治具取り外し後固定する",
"ﾘﾆｱｽｹｰﾙ等の干渉に注意する事",
"治具取り外し後固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞｱ取付け(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"2. ｺﾝﾍﾞｱ移載用治具を取り外す"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙ等の干渉に注意する事",
"治具取り外し後固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞｱ取付け(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"2. ｺﾝﾍﾞｱ移載用治具を取り外す"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙ等の干渉に注意する事",
"治具取り外し後固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WEAV-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱ移載用治具",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞｱ取付け(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"2. ｺﾝﾍﾞｱ移載用治具を取り外す",
"2. ｺﾝﾍﾞｱ移載用治具を取り外す"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙ等の干渉に注意する事",
"治具取り外し後固定する",
"ﾘﾆｱｽｹｰﾙ等の干渉に注意する事",
"治具取り外し後固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ吊治具",
"Size": "",
"ToolOther": "FM-4852",
"WorkName": "基板ﾎﾙﾀﾞ(ｼﾝｸﾞﾙ)第一実装搭載(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"2. .基板ﾎﾙﾀﾞ吊治具を取り外す",
"◆1. ①を架台に搭載する"
],
"WorkPoints": [
"速度切替えﾊﾞﾙﾌﾞｺﾈｸﾀ名称:R4212"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4852",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取り扱い",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ吊治具",
"Size": "",
"ToolOther": "FM-4852",
"WorkName": "基板ﾎﾙﾀﾞ(ｼﾝｸﾞﾙ)第一実装搭載(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"2. .基板ﾎﾙﾀﾞ吊治具を取り外す",
"◆1. ①を架台に搭載する"
],
"WorkPoints": [
"速度切替えﾊﾞﾙﾌﾞｺﾈｸﾀ名称:R4212"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4852",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取り扱い",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ吊治具",
"Size": "",
"ToolOther": "FM-4852",
"WorkName": "基板ﾎﾙﾀﾞ(ｼﾝｸﾞﾙ)第二実装搭載(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"◆1. ①を架台に搭載する"
],
"WorkPoints": [
"速度切替えﾊﾞﾙﾌﾞｺﾈｸﾀ名称:R4712"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4852",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取り扱い",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ吊治具",
"Size": "",
"ToolOther": "FM-4852",
"WorkName": "基板ﾎﾙﾀﾞ(ｼﾝｸﾞﾙ)第二実装搭載(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"◆1. ①を架台に搭載する"
],
"WorkPoints": [
"速度切替えﾊﾞﾙﾌﾞｺﾈｸﾀ名称:R4712"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-4852",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物の取り扱い",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "基板ﾎﾙﾀﾞ(ｼﾝｸﾞﾙ)取付け(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様、下受けﾋﾟﾝ一括交換式仕様、下受けﾋﾟﾝ自動交換式仕様あり)",
"WorkItems": [
"2. 仕様に対応する下受けﾌﾞﾛｯｸを下表から選択し取付ける",
"1. 全てのﾎﾙﾀﾞを搭載後､指定箇所の隙間が無いことを確認しBOLT WASHER で固定する",
"3. ㉙のスイッチをOFFにする"
],
"WorkPoints": [
"REAR",
"FRONT",
"ﾋﾟﾝ･架台当付け:0.03㎜以内",
"FRONT 左",
"FRONT 右",
"REAR 左",
"REAR 右",
"配管挟み込みに注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WEAV-G002-A01",
"InspectionItems": [
"検査表①:3.基板ﾎﾙﾀﾞﾕﾆｯﾄの取付"
],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞ(ｼﾝｸﾞﾙ)取付け(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様、下受けﾋﾟﾝ一括交換式仕様、下受けﾋﾟﾝ自動交換式仕様あり)",
"WorkItems": [
"2. 仕様に対応する下受けﾌﾞﾛｯｸを下表から選択し取付ける",
"1. 全てのﾎﾙﾀﾞを搭載後､指定箇所の隙間が無いことを確認しBOLT WASHER で固定する",
"3. ㉙のスイッチをOFFにする"
],
"WorkPoints": [
"REAR",
"FRONT",
"ﾋﾟﾝ･架台当付け:0.03㎜以内",
"FRONT 左",
"FRONT 右",
"REAR 左",
"REAR 右",
"配管挟み込みに注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:3.基板ﾎﾙﾀﾞﾕﾆｯﾄの取付",
"WEAV-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸安全警報ﾌﾞｻﾞｰ治具",
"Size": "",
"ToolOther": "FM-6136",
"WorkName": "基板ﾎﾙﾀﾞ(ｼﾝｸﾞﾙ)取付け(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様、下受けﾋﾟﾝ一括交換式仕様、下受けﾋﾟﾝ自動交換式仕様あり)",
"WorkItems": [
"2. 仕様に対応する下受けﾌﾞﾛｯｸを下表から選択し取付ける",
"1. 全てのﾎﾙﾀﾞを搭載後､指定箇所の隙間が無いことを確認しBOLT WASHER で固定する",
"3. ㉙のスイッチをOFFにする"
],
"WorkPoints": [
"REAR",
"FRONT",
"ﾋﾟﾝ･架台当付け:0.03㎜以内",
"FRONT 左",
"FRONT 右",
"REAR 左",
"REAR 右",
"配管挟み込みに注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:3.基板ﾎﾙﾀﾞﾕﾆｯﾄの取付"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-6136",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "基板ﾎﾙﾀﾞ(ｼﾝｸﾞﾙ)取付け(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様、下受けﾋﾟﾝ一括交換式仕様、下受けﾋﾟﾝ自動交換式仕様あり)",
"WorkItems": [
"2. 仕様に対応する下受けﾌﾞﾛｯｸを下表から選択し取付ける",
"1. 全てのﾎﾙﾀﾞを搭載後､指定箇所の隙間が無いことを確認しBOLT WASHER で固定する",
"3. ㉙のスイッチをOFFにする"
],
"WorkPoints": [
"REAR",
"FRONT",
"ﾋﾟﾝ･架台当付け:0.03㎜以内",
"FRONT 左",
"FRONT 右",
"REAR 左",
"REAR 右",
"配管挟み込みに注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:3.基板ﾎﾙﾀﾞﾕﾆｯﾄの取付"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞ(ｼﾝｸﾞﾙ)取付け(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様、下受けﾋﾟﾝ一括交換式仕様、下受けﾋﾟﾝ自動交換式仕様あり)",
"WorkItems": [
"2. 仕様に対応する下受けﾌﾞﾛｯｸを下表から選択し取付ける",
"1. 全てのﾎﾙﾀﾞを搭載後､指定箇所の隙間が無いことを確認しBOLT WASHER で固定する",
"3. ㉙のスイッチをOFFにする"
],
"WorkPoints": [
"REAR",
"FRONT",
"ﾋﾟﾝ･架台当付け:0.03㎜以内",
"FRONT 左",
"FRONT 右",
"REAR 左",
"REAR 右",
"配管挟み込みに注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:3.基板ﾎﾙﾀﾞﾕﾆｯﾄの取付",
"WEAV-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEAV-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "次工程引き渡し用LABELの仕分け",
"WorkItems": [
"1. LABEL LABELを仕分けし各工程に引き渡す袋に入れて引き当てる"
],
"WorkPoints": [
"B1工程前準備",
"全体ｶﾊﾞｰ工程",
"H1工程前準備"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"6K302",
"7K302",
"OPT1KK311",
"OPT2KK311",
"G111R",
"G112R",
"B1231R",
"B201R",
"B1232R",
"B1233R",
"B1234R",
"B1237R",
"B1240R",
"B1241R",
"B1242R",
"B1046/1900R",
"B1047/1901R",
"B1231TR",
"B1232TR",
"B1233TR",
"B1234TR",
"B1237TR",
"B1240TR",
"B1241TR",
"B1242TR",
"B1046/1900TR",
"B1047/1901TR",
"PUMP",
"G103R",
"G104R"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り準備出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "光ﾌｧｲﾊﾞｰｹｰﾌﾞﾙﾀｸﾞ取付",
"WorkItems": [
"1. OPTICAL-FIBER にLABEL LABEL ､OPTICAL-FIBER にLABEL LABEL を取付ける"
],
"WorkPoints": [
"使用ﾗﾍﾞﾙ;LABEL _OPT1K311",
"使用ﾗﾍﾞﾙ;LABEL _7K302",
"使用ﾗﾍﾞﾙ;LABEL _OPT2K311",
"使用ﾗﾍﾞﾙ;LABEL _6K302",
"取付け寸法(共通)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"OPT2K311",
"TOCP155TOSHIBAJAPAN",
"20mm",
"*****",
"参考;ﾀｲﾒｲﾄ EVO7SP( 締付強度指示値 1.5)",
"7K302",
"OPT1K311",
"6K302",
"K002-1",
"K002-2"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "光ﾌｧｲﾊﾞｰｹｰﾌﾞﾙ束線",
"WorkItems": [
"1. ①②に目印を付ける",
"2. 1の完成品2本をまとめマーカー位置で㉗を使いファイバー線の余りを１周させ固定し、配線長に注意し作業する"
],
"WorkPoints": [
"ﾏｰｶｰで目印(次項目でのｲﾝｼｭﾛｯｸ固定用)",
"ﾀｸﾞの方向注意①_OPT1K311",
"固定ｲﾝｼｭﾛｯｸから先端が1030㎜になる事",
"目印_ﾍﾟｲﾝﾄﾏｰｶｰ:黄色4箇所",
"ﾀｸﾞの方向注意②_OPT2K311",
"ﾀｸﾞの方向注意①_7K302",
"ﾀｸﾞの方向注意②_6K302"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"TOCP155TOSHIBAJAPAN",
"185㎜",
"*****",
"TOCP155TOSHIBAJAPAN",
"*****",
"340㎜",
"TOCP155TOSHIBAJAPAN",
"*****",
"TOCP155TOSHIBAJAPAN",
"*****",
"1030㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各指示寸法通りﾏｰｷﾝｸﾞ、結束する事±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "光ﾌｧｲﾊﾞｰｹｰﾌﾞﾙ束線",
"WorkItems": [
"1. ①②に目印を付ける",
"2. 1の完成品2本をまとめマーカー位置で㉗を使いファイバー線の余りを１周させ固定し、配線長に注意し作業する"
],
"WorkPoints": [
"ﾏｰｶｰで目印(次項目でのｲﾝｼｭﾛｯｸ固定用)",
"ﾏｰｶｰで目印",
"余る分を1周させる(7K302側が余る)",
"ﾀｸﾞの方向注意①_OPT1K311",
"340㎜ﾏｰｶｰ",
"185㎜ﾏｰｶｰ",
"固定ｲﾝｼｭﾛｯｸから先端が1030㎜になる事",
"目印_ﾍﾟｲﾝﾄﾏｰｶｰ:黄色4箇所",
"ﾀｸﾞの方向注意②_OPT2K311",
"ﾀｸﾞの方向注意①_7K302",
"ﾀｸﾞの方向注意②_6K302"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"TOCP155TOSHIBAJAPAN",
"185㎜",
"*****",
"TOCP155TOSHIBAJAPAN",
"*****",
"ｲﾝｼｭﾛｯｸ白(100mm)",
"340㎜",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"TOCP155TOSHIBAJAPAN",
"*****",
"TOCP155TOSHIBAJAPAN",
"*****",
"1030㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "各指示寸法通りﾏｰｷﾝｸﾞ、結束する事±1㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾀｰﾐﾅﾙﾌﾞﾛｯｸ検査表ﾁｪｯｸ",
"WorkItems": [
"■1. TERMINAL-BLOCK の型式を確認し製造番号(Lotの場合有)を検査書に記入する"
],
"WorkPoints": [
"型式",
"製造番号"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表TERMINAL-BLOCK :6.その他(1)型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [],
"Words": [
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰｼﾞｷﾗｰ、ﾊﾟﾜｰﾕﾆｯﾄ検査表ﾁｪｯｸ",
"WorkItems": [
"■1. ①の型式を確認し製造番号 を 検査書に記入する",
"■1. ⑥の製造番号を検査書に記入する"
],
"WorkPoints": [
"型式",
"製造番号"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表①:1.電源部(1)型式･検査書ﾁｪｯｸ",
"検査表①:1.電源部(1)型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [],
"Words": [
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾚｰｶｰ検査表ﾁｪｯｸ",
"WorkItems": [
"2. 付属品を確認する",
"■1. BREAKER の型式を確認し製造番号(Lotの場合有)を検査書に記入する"
],
"WorkPoints": [
"型式",
"製造番号",
"付属ねじは不要の為､廃棄",
"次工程で使用"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表BREAKER :1.電源部(1)型式･検査書ﾁｪｯｸ-2"
],
"WorkTypes": [],
"Words": [
"L=55",
"正面",
"右側面",
"K006-03",
"K006-04",
"K006-02",
"K006-01",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽｲｯﾁﾊﾟｰﾂ検査表ﾁｪｯｸ",
"WorkItems": [
"2. 付属品を確認する",
"■1. SWITCH-PARTS の型式を確認し製造番号(Lotの場合有)を検査書に記入する"
],
"WorkPoints": [
"型式",
"製造番号",
"付属品 3点は不要の為､廃棄",
"次工程で使用"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表SWITCH-PARTS :1.電源部(1)型式･検査書ﾁｪｯｸｰ3"
],
"WorkTypes": [],
"Words": [
"L=80",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びﾛｯﾄNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾉｲｽﾞﾌｨﾙﾀｰ部組立",
"WorkItems": [
"2. NOISE-FILTER にCABLE CABLE を組付ける",
"■1. NOISE-FILTER の型式を確認し製造番号(Lotの場合有)を検査書に記入する"
],
"WorkPoints": [
"型式",
"製造番号",
"ｱｰｽ線は架台取付用の穴を避けて締付けること",
"空端子も増し締め",
"接続後端子ｶﾊﾞｰを閉じる事"
],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m",
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表NOISE-FILTER :1.電源部(1)型式･検査書ﾁｪｯｸｰ4"
],
"WorkTypes": [],
"Words": [
"検査表②:ﾄﾙｸ計測(3)ﾉｲｽﾞﾌｨﾙﾀ -V001",
"5aV001",
"6aV001",
"1aV001",
"2aV001",
"3aV001",
"4aV001",
"EV001",
"検査表NOISE-FILTER :(3)ﾈｼﾞ締めﾄﾙｸ確認ｰ3",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "1.2N･m",
"WorkName": "ﾉｲｽﾞﾌｨﾙﾀｰ部組立",
"WorkItems": [
"2. NOISE-FILTER にCABLE CABLE を組付ける",
"■1. NOISE-FILTER の型式を確認し製造番号(Lotの場合有)を検査書に記入する"
],
"WorkPoints": [
"型式",
"製造番号",
"ｱｰｽ線は架台取付用の穴を避けて締付けること",
"空端子も増し締め",
"接続後端子ｶﾊﾞｰを閉じる事"
],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m",
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表NOISE-FILTER :(3)ﾈｼﾞ締めﾄﾙｸ確認ｰ3"
],
"WorkTypes": [],
"Words": [
"検査表②:ﾄﾙｸ計測(3)ﾉｲｽﾞﾌｨﾙﾀ -V001",
"検査表NOISE-FILTER :1.電源部(1)型式･検査書ﾁｪｯｸｰ4",
"5aV001",
"6aV001",
"1aV001",
"2aV001",
"3aV001",
"4aV001",
"EV001",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾞｼﾞﾀﾙﾄﾙｸﾒｰﾀ",
"Size": "No.2",
"ToolOther": "1.2N･m",
"WorkName": "ﾉｲｽﾞﾌｨﾙﾀｰ部組立",
"WorkItems": [
"2. NOISE-FILTER にCABLE CABLE を組付ける",
"■1. NOISE-FILTER の型式を確認し製造番号(Lotの場合有)を検査書に記入する"
],
"WorkPoints": [
"型式",
"製造番号",
"ｱｰｽ線は架台取付用の穴を避けて締付けること",
"空端子も増し締め",
"接続後端子ｶﾊﾞｰを閉じる事"
],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m",
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "WEPJ-G002-D09",
"InspectionItems": [
"検査表②:ﾄﾙｸ計測(3)ﾉｲｽﾞﾌｨﾙﾀ -V001"
],
"WorkTypes": [],
"Words": [
"検査表NOISE-FILTER :1.電源部(1)型式･検査書ﾁｪｯｸｰ4",
"5aV001",
"6aV001",
"1aV001",
"2aV001",
"3aV001",
"4aV001",
"EV001",
"検査表NOISE-FILTER :(3)ﾈｼﾞ締めﾄﾙｸ確認ｰ3",
"WEPJ-G002-D09"
]
} | {
"QualityItem": "締付ﾄﾙｸ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績所",
"StdVal": "1.2N･m±10%",
"Method": "ﾃﾞｼﾞﾀﾙﾄﾙｸﾒｰﾀ",
"RecordMethod": "WEPJ-G002-D09",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊｰﾈｽ準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.下記ﾘｽﾄの順番でｹｰﾌﾞﾙを準備する"
]
} | {
"QualityItem": "ｹｰﾌﾞﾙ準備確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り準備出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-5856",
"WorkName": "ﾊｰﾈｽ引き回1",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"L1b/L2b/L3bX101",
"基準:1a/3a/5aF101"
]
} | {
"QualityItem": "引き回経路",
"ToolManageNo": "FM-5856",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-5856",
"WorkName": "ﾊｰﾈｽ引き回2",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"EX101",
"基準:E5X001"
]
} | {
"QualityItem": "引き回経路",
"ToolManageNo": "FM-5856",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-5856",
"WorkName": "ﾊｰﾈｽ引き回3",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"基準:E7X001",
"Ed4X1"
]
} | {
"QualityItem": "引き回経路",
"ToolManageNo": "FM-5856",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-5856",
"WorkName": "ﾊｰﾈｽ引き回4",
"WorkItems": [
"1. CABLE を引き回す"
],
"WorkPoints": [
"端子下向き(ﾏｰｸﾁｭｰﾌﾞ↓)",
"端子を釘に下向きで引っかける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"基準:2/4/6bF101/E6X001",
"U/V/WaT001/ET001",
"束線ﾎﾞｰﾄﾞ"
]
} | {
"QualityItem": "引き回経路",
"ToolManageNo": "FM-5856",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-5856",
"WorkName": "ｲﾝｼｭﾛｯｸ固定",
"WorkItems": [
"1. ①の配線を下図の指示に従いｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "引き回経路",
"ToolManageNo": "FM-5856",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示された経路で配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "2.5N･m",
"WorkName": "1次側入力ﾗｲﾝ接続(ﾒｲﾝﾌﾞﾚｰｶｰ)",
"WorkItems": [
"■1. ①②の配線を③へ④で締結する"
],
"WorkPoints": [
"ｻｰｼﾞｷﾗｰが上側"
],
"Tolks": [
"締付ﾄﾙｸ 2.5N･m"
],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表①:1.電源部(3)-1ﾈｼﾞ締めﾄﾙｸ確認"
],
"WorkTypes": [],
"Words": [
"2aF101 2bF101",
"4aF101 4bF101",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.5N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "30cN･m",
"WorkName": "1次側入力ﾗｲﾝ接続(ﾒｲﾝﾌﾞﾚｰｶｰ)",
"WorkItems": [
"■2. 検査表のﾁｪｯｸ方法に従ってﾄﾙｸ計測を実施する事",
"3. 2の完成品に､⑤を⑥で締結する"
],
"WorkPoints": [
"ﾌﾞﾚｰｶｰの両ｽﾘｯﾄ",
"ﾌﾞﾚｰｶｰの両ｽﾘｯﾄに④付属品(ｶﾊﾞｰ)を取付､⑤付属品(ﾋﾞｽ)にて締結"
],
"Tolks": [
"締付ﾄﾙｸ 2.5N･m",
"締付ﾄﾙｸ 30cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"6aF101 6bF101",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾒｰﾀ",
"Size": "No.2",
"ToolOther": "2.5N･m",
"WorkName": "1次側入力ﾗｲﾝ接続(ﾒｲﾝﾌﾞﾚｰｶｰ)",
"WorkItems": [
"■2. 検査表のﾁｪｯｸ方法に従ってﾄﾙｸ計測を実施する事",
"3. 2の完成品に､⑤を⑥で締結する"
],
"WorkPoints": [
"ﾌﾞﾚｰｶｰの両ｽﾘｯﾄ",
"ﾌﾞﾚｰｶｰの両ｽﾘｯﾄに④付属品(ｶﾊﾞｰ)を取付､⑤付属品(ﾋﾞｽ)にて締結"
],
"Tolks": [
"締付ﾄﾙｸ 2.5N･m",
"締付ﾄﾙｸ 30cN･m"
],
"InspectionNo": "WEPJ-G002-D09",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"6aF101 6bF101",
"■安全作業",
"WEPJ-G002-D09"
]
} | {
"QualityItem": "締付ﾄﾙｸ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "2.5N･m±10%",
"Method": "ﾄﾙｸﾒｰﾀ",
"RecordMethod": "WEPJ-G002-D09",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾒｲﾝｽｲｯﾁﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. NUT-PLATE にBRACKET をBRACKET BOLT WASHER で組付ける"
],
"WorkPoints": [
"下記の通り組付けること",
"目安:4.5㎜",
"目安:2㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"矢視A",
"矢視A"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "2±0.5㎜4.5±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾒｲﾝｽｲｯﾁﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. NUT-PLATE にBRACKET をBRACKET BOLT WASHER で組付ける"
],
"WorkPoints": [
"下記の通り組付けること",
"目安:4.5㎜",
"目安:2㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"矢視A",
"矢視A"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "90cN･m",
"WorkName": "ﾒｲﾝｽｲｯﾁ部組立",
"WorkItems": [
"1. ①をに③をｾｯﾄする",
"2. 1の完成品を④に②PLATE で組付ける",
"■3. SWの動作確認を行う"
],
"WorkPoints": [
"ｸｯｼｮﾝの破損防止で外す",
"左側をONの向きにする",
"ON",
"OFF",
"①のﾚﾊﾞｰ部分と②の溝を合わせる",
"ﾚﾊﾞｰを下に下げ取付",
"①と③の取付向きに注意する",
"ｽｲｯﾁとﾌﾞﾚｰｶｰの向きを合わせること",
"OFF",
"ｽﾑｰｽﾞに動作する事",
"ON",
"目視で平行に組付け"
],
"Tolks": [
"締付ﾄﾙｸ 90cN･m"
],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表①:5.ﾒｲﾝSW(1)組立時調整確認"
],
"WorkTypes": [],
"Words": [
"K007-1",
"裏面",
"表面",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "1.8N･m",
"WorkName": "ﾊｰﾈｽ接続(ｱｰｽﾌﾟﾚｰﾄ・ﾀｰﾐﾅﾙﾌﾞﾛｯｸ)",
"WorkItems": [],
"WorkPoints": [
"TERMINAL のｱｰｽﾏｰｸ刻印の向きに注意"
],
"Tolks": [
"締付ﾄﾙｸ 1.8N･m",
"締付ﾄﾙｸ 1.8N･m",
"締付ﾄﾙｸ 1.8N･m"
],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表TERMINAL :ﾄﾙｸ計測(2)ｱｰｽﾌﾟﾚｰﾄ",
"検査表①:1.電源部(3)-2ﾈｼﾞ締めﾄﾙｸ確認",
"平行に取付",
"ｱｰｽﾏｰｸ",
"E7X001",
"E6X001",
"E5X001",
"E4X001",
"ｱｰｽﾏｰｸ",
"斜めに取付",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.8N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾒｰﾀ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊｰﾈｽ接続(ｱｰｽﾌﾟﾚｰﾄ・ﾀｰﾐﾅﾙﾌﾞﾛｯｸ)",
"WorkItems": [
"■2. 検査表のﾁｪｯｸ方法に従ってﾄﾙｸ計測を実施する",
"■3. 1の完成品の配線を④ﾒｲﾝﾀｰﾐﾅﾙに差込む",
"4. 3の完成品に⑤を取付ける",
"■1. ①の配線をTERMINAL へSCREW で締結する"
],
"WorkPoints": [
"TERMINAL のｱｰｽﾏｰｸ刻印の向きに注意"
],
"Tolks": [
"締付ﾄﾙｸ 1.8N･m",
"締付ﾄﾙｸ 1.8N･m",
"締付ﾄﾙｸ 1.8N･m"
],
"InspectionNo": "WEPJ-G002-D09",
"InspectionItems": [
"検査表TERMINAL :ﾄﾙｸ計測(2)ｱｰｽﾌﾟﾚｰﾄ"
],
"WorkTypes": [],
"Words": [
"L1 L1bX101",
"L2 L2bX101",
"L3 L3bX101",
"PE EX101",
"挿入向き凹凸",
"検査表①:1.電源部(2)-1ｽﾌﾟﾘﾝｸﾞ端子台の差込確認",
"検査表①:1.電源部(3)-2ﾈｼﾞ締めﾄﾙｸ確認",
"平行に取付",
"ｱｰｽﾏｰｸ",
"E7X001",
"E6X001",
"E5X001",
"E4X001",
"ｱｰｽﾏｰｸ",
"斜めに取付",
"WEPJ-G002-D09"
]
} | {
"QualityItem": "締付ﾄﾙｸ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "1.8N･m±10%",
"Method": "ﾄﾙｸﾒｰﾀ",
"RecordMethod": "WEPJ-G002-D09",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊｰﾈｽ接続(ｱｰｽﾌﾟﾚｰﾄ・ﾀｰﾐﾅﾙﾌﾞﾛｯｸ)",
"WorkItems": [
"■2. 検査表のﾁｪｯｸ方法に従ってﾄﾙｸ計測を実施する",
"■3. 1の完成品の配線を④ﾒｲﾝﾀｰﾐﾅﾙに差込む",
"4. 3の完成品に⑤を取付ける",
"■1. ①の配線をTERMINAL へSCREW で締結する"
],
"WorkPoints": [
"TERMINAL のｱｰｽﾏｰｸ刻印の向きに注意"
],
"Tolks": [
"締付ﾄﾙｸ 1.8N･m",
"締付ﾄﾙｸ 1.8N･m",
"締付ﾄﾙｸ 1.8N･m"
],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表①:1.電源部(3)-2ﾈｼﾞ締めﾄﾙｸ確認"
],
"WorkTypes": [],
"Words": [
"L1 L1bX101",
"L2 L2bX101",
"L3 L3bX101",
"PE EX101",
"挿入向き凹凸",
"検査表①:1.電源部(2)-1ｽﾌﾟﾘﾝｸﾞ端子台の差込確認",
"検査表TERMINAL :ﾄﾙｸ計測(2)ｱｰｽﾌﾟﾚｰﾄ",
"平行に取付",
"ｱｰｽﾏｰｸ",
"E7X001",
"E6X001",
"E5X001",
"E4X001",
"ｱｰｽﾏｰｸ",
"斜めに取付",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀ組立",
"WorkItems": [
"3. 1の完成品に2の完成品(ｶﾌﾟﾗ)を組付け､REGULATOR の付属ﾌﾞﾗｹｯﾄを付属ﾅｯﾄで締結する"
],
"WorkPoints": [
"15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｼｰﾙﾃｰﾌﾟを2周半巻く"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "3.5N･m",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀ組立",
"WorkItems": [
"3. 1の完成品に2の完成品(ｶﾌﾟﾗ)を組付け､REGULATOR の付属ﾌﾞﾗｹｯﾄを付属ﾅｯﾄで締結する"
],
"WorkPoints": [
"15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｼｰﾙﾃｰﾌﾟを2周半巻く"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾚｷﾞｭﾚｰﾀAC*締付治具",
"Size": "",
"ToolOther": "FM-2218",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀ組立",
"WorkItems": [
"1. REGULATOR のｺﾈｸﾀを取り外し､ﾎﾞﾙﾄとﾊﾟｯｷﾝも取り外す",
"2. COUPLER にｼｰﾙﾃｰﾌﾟを巻く",
"3. 1の完成品に2の完成品(ｶﾌﾟﾗ)を組付け､REGULATOR の付属ﾌﾞﾗｹｯﾄを付属ﾅｯﾄで締結する"
],
"WorkPoints": [
"ｺﾞﾑﾊﾟｯｷﾝ",
"ｺﾈｸﾀ",
"付属ﾌﾞﾗｹｯﾄ",
"付属ﾅｯﾄ",
"ﾎﾞﾙﾄ",
"15㎜",
"FM-2218",
"取付方向注意",
"巻き方向注意"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｼｰﾙﾃｰﾌﾟを2周半巻く",
"K019-2",
"K019-3",
"付属ﾅｯﾄ",
"付属ﾌﾞﾗｹｯﾄ",
"1~2山の掛かり代を残しｼｰﾙﾃｰﾌﾟを巻くこと"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2218",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "60cN･m",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立①",
"WorkItems": [
"1. BRACKET にCONNECTOR CONNECTOR をBOLT WASHER で組付ける",
"2. 1の完成品にGROMMET とCONNECTOR を取付ける"
],
"WorkPoints": [
"切り欠きが右側になる事",
"各ｺﾈｸﾀの凸が2ｹある方が上になる事",
"2ｾｯﾄ製作",
"裏面噛み込み注意",
"CONNECTOR の爪がBRACKET に掛かる事"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります",
"K020-1",
"K020-2",
"裏面から挿入"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立①",
"WorkItems": [
"1. BRACKET にCONNECTOR CONNECTOR をBOLT WASHER で組付ける",
"2. 1の完成品にGROMMET とCONNECTOR を取付ける"
],
"WorkPoints": [
"切り欠きが右側になる事",
"各ｺﾈｸﾀの凸が2ｹある方が上になる事",
"2ｾｯﾄ製作",
"裏面噛み込み注意",
"CONNECTOR の爪がBRACKET に掛かる事"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります",
"K020-1",
"K020-2",
"裏面から挿入"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "60cN･m",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立②",
"WorkItems": [
"1. ⑥に①②をBOLT WASHER で組付け配線を裏から接続する"
],
"WorkPoints": [
"CNEXR",
"CNDUR",
"XR",
"CNLN",
"CNDUL",
"CNEXL",
"XL",
"切欠きを上に向けて組付け"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります",
"矢視A",
"矢視A"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "連結ﾌﾞﾗｹｯﾄ組立②",
"WorkItems": [
"1. ⑥に①②をBOLT WASHER で組付け配線を裏から接続する"
],
"WorkPoints": [
"CNEXR",
"CNDUR",
"XR",
"CNLN",
"CNDUL",
"CNEXL",
"XL",
"切欠きを上に向けて組付け"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります",
"矢視A",
"矢視A"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "EMGSW組付け",
"WorkItems": [
"3. 2.の完成品にSWITCH の付属ｶﾊﾞｰを取付ける",
"■1. SWITCH の型式を確認し製造番号(Lotの場合有)を検査書に記入する",
"■2. ②にSWITCH を組付ける"
],
"WorkPoints": [
"製造番号",
"型式",
"確実に取付ける事 ※上から押さえ付けて取付",
"丸端子の取扱い注意",
"△印の向きに注意(21S､22S側)",
"ﾎﾞﾀﾝ部は取り外しH1工程前準備へ払い出す",
"下略図にて接続 ※ﾌﾛﾝﾄ､ﾘｱ用に注意",
"△印の向きに注意(11S､12S側)",
"確実に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 70cN･m"
],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表SWITCH :4.EMG SW(1)型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [],
"Words": [
"21S201",
"32S201",
"31S201",
"12S201",
"22S201",
"11S201",
"EMG SW : Front",
"EMG SW : Rear",
"21S202",
"32S202",
"31S202",
"22S202",
"11S202",
"12S202",
"検査表SWITCH :4.EMG SW(2)ﾈｼﾞ締めﾄﾙｸ",
"付属ｶﾊﾞｰ",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "70cN･m",
"WorkName": "EMGSW組付け",
"WorkItems": [
"3. 2.の完成品にSWITCH の付属ｶﾊﾞｰを取付ける",
"■1. SWITCH の型式を確認し製造番号(Lotの場合有)を検査書に記入する",
"■2. ②にSWITCH を組付ける"
],
"WorkPoints": [
"製造番号",
"型式",
"確実に取付ける事 ※上から押さえ付けて取付",
"丸端子の取扱い注意",
"△印の向きに注意(21S､22S側)",
"ﾎﾞﾀﾝ部は取り外しH1工程前準備へ払い出す",
"下略図にて接続 ※ﾌﾛﾝﾄ､ﾘｱ用に注意",
"△印の向きに注意(11S､12S側)",
"確実に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 70cN･m"
],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表SWITCH :4.EMG SW(2)ﾈｼﾞ締めﾄﾙｸ"
],
"WorkTypes": [],
"Words": [
"検査表SWITCH :4.EMG SW(1)型式･検査書ﾁｪｯｸ",
"21S201",
"32S201",
"31S201",
"12S201",
"22S201",
"11S201",
"EMG SW : Front",
"EMG SW : Rear",
"21S202",
"32S202",
"31S202",
"22S202",
"11S202",
"12S202",
"付属ｶﾊﾞｰ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "70cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "EMGSW組付け",
"WorkItems": [
"3. 2.の完成品にSWITCH の付属ｶﾊﾞｰを取付ける",
"■1. SWITCH の型式を確認し製造番号(Lotの場合有)を検査書に記入する",
"■2. ②にSWITCH を組付ける"
],
"WorkPoints": [
"製造番号",
"型式",
"確実に取付ける事 ※上から押さえ付けて取付",
"丸端子の取扱い注意",
"△印の向きに注意(21S､22S側)",
"ﾎﾞﾀﾝ部は取り外しH1工程前準備へ払い出す",
"下略図にて接続 ※ﾌﾛﾝﾄ､ﾘｱ用に注意",
"△印の向きに注意(11S､12S側)",
"確実に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 70cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表SWITCH :4.EMG SW(1)型式･検査書ﾁｪｯｸ",
"21S201",
"32S201",
"31S201",
"12S201",
"22S201",
"11S201",
"EMG SW : Front",
"EMG SW : Rear",
"21S202",
"32S202",
"31S202",
"22S202",
"11S202",
"12S202",
"検査表SWITCH :4.EMG SW(2)ﾈｼﾞ締めﾄﾙｸ",
"付属ｶﾊﾞｰ",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "50cN･m",
"WorkName": "ﾚｷﾞｭﾚｰﾀｺﾈｸﾀ組付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｷﾞｭﾚｰﾀｺﾈｸﾀ組付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "真空ﾎﾟﾝﾌﾟ前段取り",
"WorkItems": [
"■1. PUMP の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"2. PUMP に⑥を取付ける"
],
"WorkPoints": [
"外箱に検査表有り",
"型式",
"30㎜",
"PUMP の付属ﾌｨﾙﾀｰをB2工程に払い出す",
"製造番号"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表PUMP :6.その他 (1)-5 型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [],
"Words": [
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "真空ﾎﾟﾝﾌﾟ前段取り",
"WorkItems": [
"■1. PUMP の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"2. PUMP に⑥を取付ける"
],
"WorkPoints": [
"外箱に検査表有り",
"型式",
"30㎜",
"PUMP の付属ﾌｨﾙﾀｰをB2工程に払い出す",
"製造番号"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表PUMP :6.その他 (1)-5 型式･検査書ﾁｪｯｸ",
"■安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送基板段取り",
"WorkItems": [
"★2. PCB-COM の1つにCABLE を【CNB5】のｺﾈｸﾀに挿入し静電防止ｴｱｰﾏｯﾄで包みﾌﾛﾝﾄ_K323 / ﾘｱ_K324を表記する",
"■★1. PCB-COM の型式をﾁｪｯｸし､製造番号を検査表に記入する"
],
"WorkPoints": [
"K323⇒CABLE ｼｮｰﾄｺﾈｸﾀあり:1枚/K324⇒CABLE ｼｮｰﾄｺﾈｸﾀなし:1枚(ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様)",
"製造番号",
"型式"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表PCB-COM :3.基板関係(1)型式･検査書ﾁｪｯｸｰ3,4"
],
"WorkTypes": [],
"Words": [
"K025A-1【ﾌﾛﾝﾄ用_K323】",
"K025-2 【ﾘｱ用_K324】",
"表記例",
"検査表PCB-COM :6.その他 (2)ｺﾈｸﾀ接続確認",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "検査表の有無を確認する事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送基板段取り",
"WorkItems": [
"★2. PCB-COM の1つにCABLE を【CNB5】のｺﾈｸﾀに挿入し静電防止ｴｱｰﾏｯﾄで包みﾌﾛﾝﾄ_K323 / ﾘｱ_K324を表記する",
"■★1. PCB-COM の型式をﾁｪｯｸし､製造番号を検査表に記入する"
],
"WorkPoints": [
"K323⇒CABLE ｼｮｰﾄｺﾈｸﾀあり:1枚/K324⇒CABLE ｼｮｰﾄｺﾈｸﾀなし:1枚(ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様)",
"製造番号",
"型式"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表PCB-COM :6.その他 (2)ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"検査表PCB-COM :3.基板関係(1)型式･検査書ﾁｪｯｸｰ3,4",
"K025A-1【ﾌﾛﾝﾄ用_K323】",
"K025-2 【ﾘｱ用_K324】",
"表記例",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "I/O基板段取り",
"WorkItems": [
"■1. PCB-COM の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"2. 基板をｴｱｰﾏｯﾄで包み､ﾌﾛﾝﾄ_K321及びﾘｱ_K322を表記する"
],
"WorkPoints": [
"型式",
"製造番号"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表PCB-COM :3.基板関係(1)型式･検査書ﾁｪｯｸ-1,2"
],
"WorkTypes": [],
"Words": [
"裏面",
"表面",
"K026-1",
"K026-2",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "検査表の有無を確認する事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN前段取り",
"WorkItems": [
"■1. FAN FAN の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"2. FAN FAN のｺﾈｸﾀにﾀｸﾞ③を取付ける"
],
"WorkPoints": [
"製造番号",
"型式",
"FAN 架台下用FANに【G111R】､FAN 真空ﾎﾟﾝﾌﾟ冷却用FANに【G112R】を取付ける",
"ﾀｸﾞの端面と保護ﾁｭｰﾌﾞの端面を合わせて固定",
"製造番号",
"型式",
"架台下用【G111R】",
"真空ﾎﾟﾝﾌﾟ冷却用【G112R】"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表FAN :6.その他(1)型式･検査書ﾁｪｯｸｰ3,4"
],
"WorkTypes": [],
"Words": [
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN前段取り",
"WorkItems": [
"■1. FAN FAN の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"2. FAN FAN のｺﾈｸﾀにﾀｸﾞ③を取付ける"
],
"WorkPoints": [
"製造番号",
"型式",
"FAN 架台下用FANに【G111R】､FAN 真空ﾎﾟﾝﾌﾟ冷却用FANに【G112R】を取付ける",
"ﾀｸﾞの端面と保護ﾁｭｰﾌﾞの端面を合わせて固定",
"製造番号",
"型式",
"架台下用【G111R】",
"真空ﾎﾟﾝﾌﾟ冷却用【G112R】"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表FAN :6.その他(1)型式･検査書ﾁｪｯｸｰ3,4"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "架台下用FAN組立",
"WorkItems": [
"1. ①にFAN-GUARD をBOLT WASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"FLOW方向に注意する事",
"FLOW方向",
"FAN-GUARD FUN-GUARDの取付け方向注意"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台下用FAN組立",
"WorkItems": [
"1. ①にFAN-GUARD をBOLT WASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"FLOW方向に注意する事",
"FLOW方向",
"FAN-GUARD FUN-GUARDの取付け方向注意"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "78cN･m",
"WorkName": "真空ﾎﾟﾝﾌﾟ冷却用FAN組立",
"WorkItems": [
"1. ①にFAN-GUARD をBOLT WASHER WASHER NUT WASHER で取付ける",
"2 1完成品にPLATE FAN-FILTER をWASHER NUT WASHER WASHER WASHER で組付ける",
"1. ①にFAN-GUARD をBOLT WASHER WASHER NUT WASHER で取付ける",
"2 1完成品にPLATE FAN-FILTER をWASHER NUT WASHER WASHER WASHER で組付ける"
],
"WorkPoints": [
"･取付順番に注意する事･①の配線とFAN-GUARD の向き注意する事",
"取付順番に注意する事",
"FAN-GUARD の折り曲げ",
"PLATE の取付方向の詳細",
"･取付順番に注意する事･①の配線とFAN-GUARD の向き注意する事",
"取付順番に注意する事",
"FAN-GUARD の折り曲げ",
"PLATE の取付方向の詳細"
],
"Tolks": [
"締付ﾄﾙｸ 78cN･m",
"締付ﾄﾙｸ 78cN･m",
"締付ﾄﾙｸ 78cN･m",
"締付ﾄﾙｸ 78cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"裏面",
"表面",
"取付け方向に注意!PLATE の部品には方向性があります｡",
"広い",
"狭い",
"裏面",
"表面",
"裏面",
"表面",
"取付け方向に注意!PLATE の部品には方向性があります｡",
"広い",
"狭い",
"裏面",
"表面"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "78cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "真空ﾎﾟﾝﾌﾟ冷却用FAN組立",
"WorkItems": [
"1. ①にFAN-GUARD をBOLT WASHER WASHER NUT WASHER で取付ける",
"2 1完成品にPLATE FAN-FILTER をWASHER NUT WASHER WASHER WASHER で組付ける"
],
"WorkPoints": [
"･取付順番に注意する事･①の配線とFAN-GUARD の向き注意する事",
"取付順番に注意する事",
"FAN-GUARD の折り曲げ",
"穴ｱﾘ",
"穴ｱﾘ",
"穴ﾅｼ",
"穴ﾅｼ",
"穴ｱﾘ",
"穴ﾅｼ",
"PLATE の取付方向の詳細"
],
"Tolks": [
"締付ﾄﾙｸ 78cN･m",
"締付ﾄﾙｸ 78cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"裏面",
"表面",
"矢視A",
"矢視A",
"取付け方向に注意!PLATE の部品には方向性があります｡",
"広い",
"狭い",
"裏面",
"表面",
"広い",
"狭い",
"広い",
"穴有",
"狭い",
"広い"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "32㎜",
"ToolOther": "4N･m",
"WorkName": "ｹｰﾌﾞﾙｻﾎﾟｰﾄ組立",
"WorkItems": [
"1. PLATE にCABLE-SUPPORT を組付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 4N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "4N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "天板受けﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. BRACKET にSPACER をBOLT WASHER で組付ける"
],
"WorkPoints": [
"㉘にクランプさせて作業実施"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"※4ｾｯﾄ組立"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾞﾛﾒｯﾄ前準備",
"WorkItems": [
"1. GROMMET に切り込みを入れる"
],
"WorkPoints": [
"縦横切り込み長さ:35㎜~40㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"※4ｾｯﾄ製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "35~40㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立①",
"WorkItems": [
"1. PLATE PLATE にSCREW をNUT で組付ける",
"2. 1の完成品にSTOPPER を挿入する"
],
"WorkPoints": [
"ｽﾄｯﾊﾟｰの潰れ代を1㎜以上確保すること",
"SCREW の六角穴の向きに注意する",
"SCREW の六角穴の向きに注意する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"28.5㎜",
"30㎜",
"1.0~1.5㎜",
"組付け寸法"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立①",
"WorkItems": [
"1. PLATE PLATE にSCREW をNUT で組付ける",
"2. 1の完成品にSTOPPER を挿入する"
],
"WorkPoints": [
"ｽﾄｯﾊﾟｰの潰れ代を1㎜以上確保すること",
"SCREW の六角穴の向きに注意する",
"SCREW の六角穴の向きに注意する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"28.5㎜",
"30㎜",
"1.0~1.5㎜",
"組付け寸法"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立②",
"WorkItems": [
"1. ①②にCLIP をBOLT で組付ける",
"2.①にBLOCK をBOLT で組付ける",
"3.①にSPACER をBOLT WASHER で組付ける"
],
"WorkPoints": [
"方向に注意",
"裏側から下方向に押当てで組付け"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"押当て",
"裏面",
"表面"
]
} | {
"QualityItem": "取付方向確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立②",
"WorkItems": [
"1. ①②にCLIP をBOLT で組付ける",
"2.①にBLOCK をBOLT で組付ける",
"3.①にSPACER をBOLT WASHER で組付ける"
],
"WorkPoints": [
"裏側から下方向に押当てで組付け"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"押当て"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸ｽﾄｯﾊﾟｰ位置決め調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6437",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立②",
"WorkItems": [
"1. ①②にCLIP をBOLT で組付ける",
"2.①にBLOCK をBOLT で組付ける",
"3.①にSPACER をBOLT WASHER で組付ける"
],
"WorkPoints": [
"方向に注意",
"裏側から下方向に押当てで組付け"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"押当て",
"裏面",
"表面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6437",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立②",
"WorkItems": [
"1. ①②にCLIP をBOLT で組付ける",
"2.①にBLOCK をBOLT で組付ける",
"3.①にSPACER をBOLT WASHER で組付ける"
],
"WorkPoints": [
"裏側から下方向に押当てで組付け"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"押当て"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ組立②",
"WorkItems": [
"1. ①②にCLIP をBOLT で組付ける",
"2.①にBLOCK をBOLT で組付ける",
"3.①にSPACER をBOLT WASHER で組付ける"
],
"WorkPoints": [
"裏側から下方向に押当てで組付け"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"押当て"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ACｻｰﾎﾞﾓｰﾀﾄﾞﾗｲﾊﾞｰ前準備",
"WorkItems": [
"■1. MOTOR-DRIVER MOTOR-DRIVER の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"3. 検査表の指示に従いMOTOR-DRIVER MOTOR-DRIVER のｱﾄﾞﾚｽ設定を行う",
"2. MOTOR-DRIVER MOTOR-DRIVER にフロント_FYM及びリア_RYMと㉗テープで表記する"
],
"WorkPoints": [
"型式",
"製造番号",
"表に基づきﾄﾞﾗｲﾊﾞｰに負荷名称を表記する",
"ｱﾄﾞﾚｽ設定表",
"必ず表記と合わせること",
"K035-1",
"K035-2",
"K035-3",
"K035-4",
"K035-5",
"K035-6"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表MOTOR-DRIVER :2.ﾄﾞﾗｲﾊﾞｰ設定(2)負荷設定確認"
],
"WorkTypes": [],
"Words": [
"表記例",
"矢視A",
"矢視A",
"矢視B",
"検査表MOTOR-DRIVER :2.ﾄﾞﾗｲﾊﾞｰ設定(1)型式･検査書ﾁｪｯｸ",
"ﾌﾛﾝﾄ",
"ﾘｱ",
"FYM",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ACｻｰﾎﾞﾓｰﾀﾄﾞﾗｲﾊﾞｰ前準備",
"WorkItems": [
"■1. MOTOR-DRIVER MOTOR-DRIVER の型式をﾁｪｯｸし､製造番号を検査表に記入する",
"3. 検査表の指示に従いMOTOR-DRIVER MOTOR-DRIVER のｱﾄﾞﾚｽ設定を行う",
"2. MOTOR-DRIVER MOTOR-DRIVER にフロント_FYM及びリア_RYMと㉗テープで表記する"
],
"WorkPoints": [
"型式",
"製造番号",
"表に基づきﾄﾞﾗｲﾊﾞｰに負荷名称を表記する",
"ｱﾄﾞﾚｽ設定表",
"必ず表記と合わせること",
"K035-1",
"K035-2",
"K035-3",
"K035-4",
"K035-5",
"K035-6"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表MOTOR-DRIVER :2.ﾄﾞﾗｲﾊﾞｰ設定(1)型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [],
"Words": [
"表記例",
"矢視A",
"矢視A",
"矢視B",
"検査表MOTOR-DRIVER :2.ﾄﾞﾗｲﾊﾞｰ設定(2)負荷設定確認",
"ﾌﾛﾝﾄ",
"ﾘｱ",
"FYM",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "194cN･m",
"WorkName": "X軸ﾄﾞﾗｲﾊﾞｰ前準備",
"WorkItems": [
"1. ①②にBRACKET をSCREW で組付ける",
"2. ①②にフロント_ＦＸ及びリア_ＲＸと㉘テープで表記する"
],
"WorkPoints": [
"①K035-1_FX軸(ﾌﾛﾝﾄ):K036-1②K035-4_RX軸(ﾘｱ):K036-2"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"矢視A",
"矢視A",
"矢視B",
"矢視B",
"FX",
"RX"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPUBOX前準備",
"WorkItems": [
"■1. ①の製造番号を検査表に記入する",
"2. ①にBRACKET をBOLT WASHER で組付ける"
],
"WorkPoints": [
"この部分の番号を記入",
"CPU BOXの底面と面合わせ"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "WEPJ-G002-D04",
"InspectionItems": [
"検査表①:6.その他 (1)型式･検査書ﾁｪｯｸｰ1"
],
"WorkTypes": [],
"Words": [
"BFG",
"UNI01※-BFG",
"WEPJ-G002-D04"
]
} | {
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.2N･m",
"WorkName": "CPUBOX前準備",
"WorkItems": [
"■1. ①の製造番号を検査表に記入する",
"2. ①にBRACKET をBOLT WASHER で組付ける"
],
"WorkPoints": [
"この部分の番号を記入",
"CPU BOXの底面と面合わせ"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:6.その他 (1)型式･検査書ﾁｪｯｸｰ1",
"BFG",
"UNI01※-BFG",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾏｸﾞﾈｯﾄｶﾊﾞｰ前段取り",
"WorkItems": [],
"WorkPoints": [
"この作業では同じものを2個製作",
"この作業では同じものを2個製作",
"LABEL の▼向きに注意する事",
"LABEL の▼向きに注意する事",
"この作業では同じものを2個製作",
"この作業では同じものを2個製作",
"LABEL の▼向きに注意する事",
"LABEL の▼向きに注意する事",
"この作業では同じものを2個製作",
"この作業では同じものを2個製作",
"LABEL の▼向きに注意する事",
"LABEL の▼向きに注意する事",
"この作業では同じものを2個製作",
"この作業では同じものを2個製作",
"LABEL の▼向きに注意する事",
"LABEL の▼向きに注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"下面合わせ",
"200mm",
"下面合わせ",
"200mm",
"下面合わせ",
"200mm",
"下面合わせ",
"200mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "CPUBOX(P10A)取付用ﾌﾞﾗｹｯﾄ前準備",
"WorkItems": [
"1. BRACKET にCOVER を指定長さにｶｯﾄして取付ける"
],
"WorkPoints": [
"ｶｯﾄ寸法:40㎜×2本",
"外側の端面に合わせて貼付ける",
"外側の端面に合わせて貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPUBOX(P10A)取付用ﾌﾞﾗｹｯﾄ前準備",
"WorkItems": [
"1. BRACKET にCOVER を指定長さにｶｯﾄして取付ける"
],
"WorkPoints": [
"ｶｯﾄ寸法:40㎜×2本",
"外側の端面に合わせて貼付ける",
"外側の端面に合わせて貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "50cN･m",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"1. BRACKET にVALVE をBOLT WASHER WASHER でVALVE をBOLT WASHER で組付ける",
"2. TUBE を指定長さにｶｯﾄして1の完成品に取付ける"
],
"WorkPoints": [
"WASHER AWを間に挟む",
"ﾎﾟｰﾄ4",
"BRACKET VALVE "
],
"Tolks": [
"締付ﾄﾙｸ 55cN･m",
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"仕様により組立数が違います｡ ﾘｱ側台車仕様時:2ｾｯﾄ組立 ﾘｱ側ﾄﾚｲ仕様時:1ｾｯﾄ組立"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "55cN･m",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ組立",
"WorkItems": [],
"WorkPoints": [
"ｶｯﾄ寸法:240㎜×2本",
"ﾎﾟｰﾄ2(白ﾗｲﾝ)",
"VALVE の取付方向注意(矢印▲)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "55cN･m±5%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.