input stringclasses 1
value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "A003ﾌﾞﾗｹｯﾄ組立4",
"WorkItems": [
"1. ①にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"ﾏｳﾝﾄ方向指示の為､ｲﾝｼｭﾛｯｸを表示しております"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じもの... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "A003ﾌﾞﾗｹｯﾄ組立5",
"WorkItems": [
"1. ①にCLIP をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "A003ﾌﾞﾗｹｯﾄ組立6",
"WorkItems": [
"◆1. BOLT にｸﾞﾘｰｽを塗布する",
"2. PLATE にBEARING SPACER WASHER を1完成品とNUT で仮に取付ける",
"3. 2完成品を⑤にBOLT で取付ける"
],
"WorkPoints": [
"目視で真直ぐ取付ける",
"仮止め:SD-A033501-112にて本締め",
"ｸﾞﾘ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "A003ﾌﾞﾗｹｯﾄ組立6",
"WorkItems": [
"◆1. BOLT にｸﾞﾘｰｽを塗布する",
"2. PLATE にBEARING SPACER WASHER を1完成品とNUT で仮に取付ける",
"3. 2完成品を⑤にBOLT で取付ける"
],
"WorkPoints": [
"PLATE の溝にﾅｯﾄをはめる事",
"目視で真直ぐ取付ける",
"仮止め:SD-A033501-112にて本締... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "1.4N･m",
"WorkName": "可動ﾌﾞﾗｹｯﾄ組立1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.4N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "可動ﾌﾞﾗｹｯﾄ組立1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:1粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "可動ﾌﾞﾗｹｯﾄ組立2",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"LABEL の貼付け面をｱﾙｺｰﾙにて清掃"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを4個製作",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "可動ﾌﾞﾗｹｯﾄ組立3",
"WorkItems": [
"1. ①にDOG をBOLT WASHER で取付ける"
],
"WorkPoints": [
"DOG の向きに注意する事",
"ﾄﾞｸﾞの傾きが無き事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "可動ﾌﾞﾗｹｯﾄ組立3",
"WorkItems": [
"1. ①にDOG をBOLT WASHER で取付ける"
],
"WorkPoints": [
"DOG の向きに注意する事",
"ﾄﾞｸﾞの傾きが無き事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTyp... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "8㎜",
"ToolOther": "",
"WorkName": "可動ﾌﾞﾗｹｯﾄ組立3",
"WorkItems": [
"1. ①にDOG をBOLT WASHER で取付ける"
],
"WorkPoints": [
"DOG の向きに注意する事",
"ﾄﾞｸﾞの傾きが無き事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "取付け寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "可動ﾌﾞﾗｹｯﾄ組立4",
"WorkItems": [
"1. ①にDOG をBOLT WASHER で取付ける"
],
"WorkPoints": [
"DOG の向きに注意する事",
"ﾄﾞｸﾞの傾きが無き事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "可動ﾌﾞﾗｹｯﾄ組立4",
"WorkItems": [
"1. ①にDOG をBOLT WASHER で取付ける"
],
"WorkPoints": [
"DOG の向きに注意する事",
"ﾄﾞｸﾞの傾きが無き事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTyp... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "8㎜",
"ToolOther": "",
"WorkName": "可動ﾌﾞﾗｹｯﾄ組立4",
"WorkItems": [
"1. ①にDOG をBOLT WASHER で取付ける"
],
"WorkPoints": [
"DOG の向きに注意する事",
"ﾄﾞｸﾞの傾きが無き事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "取付け寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "幅寄せ部組立1",
"WorkItems": [
"1. ①②にBALL-SCREW を挿入する",
"2. 1完成品に③④を挿入する",
"3. 2完成品にCOLLAR を挿入しNUT で仮固定する"
],
"WorkPoints": [
"ﾄﾞｸﾞあり",
"③ﾄﾞｸﾞなし(ﾚｰﾝ1左用)⑨ﾄﾞｸﾞあり(ﾚｰﾝ2右用)",
"この作業では同様のものを2個製作"
],
"Tolks": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "幅寄せ部組立2",
"WorkItems": [
"1. ①②を互いに挿入する",
"2. 1完成品にBEARING を挿入しC-RING で止める"
],
"WorkPoints": [
"ﾄﾞｸﾞあり",
"ﾄﾞｸﾞあり",
"ﾄﾞｸﾞあり",
"ﾄﾞｸﾞなし",
"C-RING はﾍﾞｱﾘﾝｸﾞ側に面取りがある事"
],
"Tolks": [],
"InspectionNo": ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "固定搬送ﾚｰﾙ組立1",
"WorkItems": [
"1. FRAME にPIN を圧入する"
],
"WorkPoints": [
"出代:4㎜",
"出代:4㎜",
"出代:4.5㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:4.0㎜±0.5㎜出代:4.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "固定搬送ﾚｰﾙ組立2【ﾌﾛﾝﾄ】",
"WorkItems": [
"1. ①にLABEL LABEL LABEL ⑨LABEL を貼付ける"
],
"WorkPoints": [
"延長なし",
"延長あり",
"延長なし",
"延長あり"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "固定搬送ﾚｰﾙ組立3【ﾘｱ】",
"WorkItems": [
"1. ①にLABEL LABEL LABEL LABEL を貼付ける"
],
"WorkPoints": [
"延長なし",
"延長あり",
"延長なし",
"延長あり"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "固定搬送ﾚｰﾙ組立4",
"WorkItems": [
"2. ①②にGUIDE をBOLT で仮に取付ける",
"1. ①②GUIDE の取付け面にｱﾙｶﾝｻｽをかける"
],
"WorkPoints": [
"X方向はﾈｼﾞ穴ｾﾝﾀｰで取付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wor... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "固定搬送ﾚｰﾙ組立5",
"WorkItems": [
"1. GUIDE の取付け面にｱﾙｶﾝｻｽをかける",
"2. ①②にGUIDE をBOLT WASHER で仮に取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"仮止め:SD-A03... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "固定搬送ﾚｰﾙ組立6",
"WorkItems": [
"1. ①②にGUIDE GUIDE をBOLT WASHER で仮に取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"仮止め:SD-A033501... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ｶﾞｲﾄﾞ位置決め治具(実装部)1.6㎜",
"Size": "",
"ToolOther": "FM-3558",
"WorkName": "固定搬送ﾚｰﾙ組立7",
"WorkItems": [
"1. ①②のｶﾞｲﾄﾞ位置を調整する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"0.1㎜",... | {
"QualityItem": "段差確認",
"ToolManageNo": "FM-3558",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "基板ｶﾞｲﾄﾞ位置決め治具(実装部)1.6㎜",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ｶﾞｲﾄﾞ位置出し治具(待機部)",
"Size": "2.8㎜",
"ToolOther": "FM-2845",
"WorkName": "固定搬送ﾚｰﾙ組立7",
"WorkItems": [
"1. ①②のｶﾞｲﾄﾞ位置を調整する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"0.1㎜",... | {
"QualityItem": "段差確認",
"ToolManageNo": "FM-2845",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "基板ｶﾞｲﾄﾞ位置出し治具(待機部)",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "固定搬送ﾚｰﾙ組立7",
"WorkItems": [
"1. ①②のｶﾞｲﾄﾞ位置を調整する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"0.1㎜",
"0.1㎜",
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.1㎜で取付ける事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "68cN･m",
"WorkName": "固定搬送ﾚｰﾙ組立8",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 68cN･m",
"締付ﾄﾙｸ 68cN･m",
"締付ﾄﾙｸ 68cN･m",
"締付ﾄﾙｸ 68cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "68cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "固定搬送ﾚｰﾙ組立9",
"WorkItems": [
"1. ①②にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"FT4 向き"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "固定搬送ﾚｰﾙ組立10",
"WorkItems": [
"1. PLATE にCLIP をBOLT で取付ける"
],
"WorkPoints": [
"この作業では同じものを各2個製作"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "固定搬送ﾚｰﾙ組立11",
"WorkItems": [
"1. ①②に③④をBOLT ⑰WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "可動搬送ﾚｰﾙ組立1",
"WorkItems": [
"1. FRAME にLABEL LABEL LABEL LABEL を貼付ける"
],
"WorkPoints": [
"延長なし",
"延長あり",
"延長なし",
"延長あり"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes":... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "可動搬送ﾚｰﾙ組立2",
"WorkItems": [
"2. ①にGUIDE をBOLT で仮に取付ける",
"1. ①GUIDE の取付け面にｱﾙｶﾝｻｽをかける"
],
"WorkPoints": [
"X方向はﾈｼﾞ穴ｾﾝﾀｰで取付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "可動搬送ﾚｰﾙ組立3",
"WorkItems": [
"2. ①にGUIDE をBOLT WASHER で仮に取付ける",
"1. GUIDE の取付け面にｱﾙｶﾝｻｽをかける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "可動搬送ﾚｰﾙ組立4",
"WorkItems": [
"1. ①にGUIDE GUIDE PLATE をBOLT で仮に取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"仮止め:SD-A033501-1... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ｶﾞｲﾄﾞ位置決め治具(実装部)1.6㎜",
"Size": "",
"ToolOther": "FM-3558",
"WorkName": "可動搬送ﾚｰﾙ組立5",
"WorkItems": [
"1. ①のｶﾞｲﾄﾞ位置を調整する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"0.1㎜",
... | {
"QualityItem": "段差確認",
"ToolManageNo": "FM-3558",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "基板ｶﾞｲﾄﾞ位置決め治具(実装部)1.6㎜",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ｶﾞｲﾄﾞ位置出し治具(待機部)",
"Size": "2.8㎜",
"ToolOther": "FM-2845",
"WorkName": "可動搬送ﾚｰﾙ組立5",
"WorkItems": [
"1. ①のｶﾞｲﾄﾞ位置を調整する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"0.1㎜",
... | {
"QualityItem": "段差確認",
"ToolManageNo": "FM-2845",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "基板ｶﾞｲﾄﾞ位置出し治具(待機部)",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "可動搬送ﾚｰﾙ組立5",
"WorkItems": [
"1. ①のｶﾞｲﾄﾞ位置を調整する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"0.1㎜",
"0.1㎜",
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.1㎜で取付ける事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "68cN･m",
"WorkName": "可動搬送ﾚｰﾙ組立6",
"WorkItems": [
"1. ①にPULLEY を取付ける",
"2. 1完成品にPULLEY をNUT で取付ける",
"1. ①にPULLEY を取付ける",
"2. 1完成品にPULLEY をNUT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"Inspection... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "68cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "可動搬送ﾚｰﾙ組立7",
"WorkItems": [
"1. ①にCABLE-SUPPORT を取付ける",
"2. 1完成品にCLIP をBOLT で取付ける"
],
"WorkPoints": [
"FT4 向き"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "可動搬送ﾚｰﾙ組立8",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "可動搬送ﾚｰﾙ組立9",
"WorkItems": [
"1. DUCT にBUSH を貼付ける"
],
"WorkPoints": [
"この作業では同じものを2個製作",
"BUSH を指定寸法にｶｯﾄする ※上表参照"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "可動搬送ﾚｰﾙ組立9",
"WorkItems": [
"1. DUCT にBUSH を貼付ける"
],
"WorkPoints": [
"この作業では同じものを2個製作",
"BUSH を指定寸法にｶｯﾄする ※上表参照"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "7㎜BOX",
"ToolOther": "110cN･m",
"WorkName": "ｹｰﾌﾞﾙﾍﾞｱﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. BRACKET にBRACKET をBOLT NUT WASHER で取付ける"
],
"WorkPoints": [
"BRACKET とBRACKET の向きに注意する事",
"ﾅｯﾄをﾄﾙｸﾄﾞﾗｲﾊﾞｰで締付け",
"ﾌﾞﾗｹｯﾄと平行に取付ける事",
"ﾌﾞﾗｹｯﾄと平行に取付ける事"
],... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "可動搬送ﾚｰﾙﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. ①に②③をBOLT WASHER で取付ける"
],
"WorkPoints": [
"下方向に押し当て",
"下方向に押し当て"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "+№0",
"ToolOther": "18cN･m",
"WorkName": "下受けﾋﾟﾝ検出ｾﾝｻ組立",
"WorkItems": [
"1. BRACKET BRACKET にSENSOR を④で取付ける",
"2. 1完成品にの配線を固定する"
],
"WorkPoints": [
"黒線:受光側",
"ｲﾝｼｭﾛｯｸの頭をｾﾝｻｰの 反対側に来るよう結束の事",
"この作業では同じものを2個製作"
],
"Tolks": [],
"In... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "18cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "下受けﾋﾟﾝ検出ｾﾝｻ組立",
"WorkItems": [
"3. 2完成品にLabel Label を取付ける"
],
"WorkPoints": [
"白線:投光側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B121R",
"B125R",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送ﾌﾟｰﾘｰ組立",
"WorkItems": [
"1. PULLEY にRING を嵌め込む"
],
"WorkPoints": [
"ﾘﾝｸﾞがﾌﾟｰﾘｰの溝に全周にわたり嵌っている事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを12個製作"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "自幅ﾌﾟｰﾘｰ組立",
"WorkItems": [
"1. PULLEY にSCREW を入れる"
],
"WorkPoints": [
"ﾓｰﾀ側",
"この作業では同じものを2個製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "300cN･m",
"WorkName": "搬送ﾓｰﾀ組立固定ﾚｰﾙ用",
"WorkItems": [
"1. MOTOR に②をSCREW で取付ける"
],
"WorkPoints": [
"Dｶｯﾄ面で締め付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "2.6㎜",
"ToolOther": "",
"WorkName": "搬送ﾓｰﾀ組立固定ﾚｰﾙ用",
"WorkItems": [
"1. MOTOR に②をSCREW で取付ける"
],
"WorkPoints": [
"Dｶｯﾄ面で締め付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Word... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "300cN･m",
"WorkName": "搬送ﾓｰﾀ組立可動ﾚｰﾙ用",
"WorkItems": [
"1. MOTOR に②をSCREW で取付ける"
],
"WorkPoints": [
"Dｶｯﾄ面で締め付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "3.8㎜",
"ToolOther": "",
"WorkName": "搬送ﾓｰﾀ組立可動ﾚｰﾙ用",
"WorkItems": [
"1. MOTOR に②をSCREW で取付ける"
],
"WorkPoints": [
"Dｶｯﾄ面で締め付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Word... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "300cN･m",
"WorkName": "幅寄せﾓｰﾀ組立",
"WorkItems": [
"1. MOTOR に②を取付ける"
],
"WorkPoints": [
"この作業では同じものを2個製作",
"Dｶｯﾄ面で締め付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkT... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "2.7㎜",
"ToolOther": "",
"WorkName": "幅寄せﾓｰﾀ組立",
"WorkItems": [
"1. MOTOR に②を取付ける"
],
"WorkPoints": [
"この作業では同じものを2個製作",
"Dｶｯﾄ面で締め付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": ... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "搬送ﾓｰﾀ組立固定用1",
"WorkItems": [
"1. PLATE に①をBOLT WASHER WASHER で取付ける",
"2. 1完成品に②SPACER をBOLT WASHER WASHER BOLT WASHER で取付ける",
"1. PLATE に①をBOLT WASHER WASHER で取付ける",
"2. 1完成品に②SPACER をBOLT WASHER WASHER BOLT WAS... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "搬送ﾓｰﾀ組立固定用1",
"WorkItems": [
"1. PLATE に①をBOLT WASHER WASHER で取付ける",
"2. 1完成品に②SPACER をBOLT WASHER WASHER BOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 194cN･m",
"締... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "搬送ﾓｰﾀ組立固定用2",
"WorkItems": [],
"WorkPoints": [
"ｺﾈｸﾀ差込口が上の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "68cN･m",
"WorkName": "搬送ﾓｰﾀ組立固定用2",
"WorkItems": [
"1. PLATE にPULLEY をNUT WASHER で取付ける",
"2. 1完成品に①をWASHER BOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 68cN･m"
],
"InspectionNo": "",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "68cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "搬送ﾓｰﾀ組立可動用1",
"WorkItems": [
"2. 1完成品にBRACKET をWASHER BOLT で取付ける"
],
"WorkPoints": [
"矢印方向に当付け"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "搬送ﾓｰﾀ組立可動用1",
"WorkItems": [
"1. ①にPLATE をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "搬送ﾓｰﾀ組立可動用2",
"WorkItems": [
"1. ①にPLATE をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ｺﾈｸﾀ差込口が上の事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "搬送ﾓｰﾀ組立可動用2",
"WorkItems": [
"1. ①にPLATE をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ｺﾈｸﾀ差込口が上の事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "ｹｰﾌﾞﾙ受けﾌﾟﾚｰﾄ組立1",
"WorkItems": [
"2. 1完成品にBRACKET をBOLT NUT WASHER で取付ける"
],
"WorkPoints": [
"曲がり無い事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionI... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｹｰﾌﾞﾙ受けﾌﾟﾚｰﾄ組立1",
"WorkItems": [
"1. PLATE にCOVER COVER を貼付ける",
"3. 2完成品にPLATE をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ受けﾌﾟﾚｰﾄ組立2",
"WorkItems": [
"1. ①にAMPLIFIER AMPLIFIER を取付ける"
],
"WorkPoints": [
"ﾌｧｲﾊﾞｰ線差込口 4ｹ",
"ﾌｧｲﾊﾞｰ線差込口 5ｹ",
"ﾌｧｲﾊﾞｰ線差込口 3ｹ",
"ﾌｧｲﾊﾞｰ線差込口 2ｹ",
"ｽﾗｲﾄﾞ搬送OP時 4ｹ",
"ｽﾗｲﾄﾞ搬送OP時 5ｹ",
"ｱﾝﾌﾟ取付け方法"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ受けﾌﾟﾚｰﾄ組立2",
"WorkItems": [
"1. ①にAMPLIFIER AMPLIFIER を取付ける"
],
"WorkPoints": [
"ﾌｧｲﾊﾞｰ線差込口 4ｹ",
"ﾌｧｲﾊﾞｰ線差込口 5ｹ",
"ﾌｧｲﾊﾞｰ線差込口 3ｹ",
"ﾌｧｲﾊﾞｰ線差込口 2ｹ",
"ｽﾗｲﾄﾞ搬送OP時 4ｹ",
"ｽﾗｲﾄﾞ搬送OP時 5ｹ",
"ｱﾝﾌﾟ取付け... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ受けﾌﾟﾚｰﾄ組立3",
"WorkItems": [
"1. ①にLABEL LABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"25㎜",
"右側",
"25㎜",
"11㎜",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ受けﾌﾟﾚｰﾄ組立4",
"WorkItems": [
"1. ①にLABEL LABEL LABEL LABEL を貼付ける"
],
"WorkPoints": [
"ｽﾗｲﾄﾞ搬送OP時",
"ｽﾗｲﾄﾞ搬送OP時"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ受けﾌﾟﾚｰﾄ組立5",
"WorkItems": [
"1. ①②にｲﾝｼｭﾛｯｸを通す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ｼﾝｸﾞﾙﾓｰﾄﾞ原点ｾﾝｻ組立",
"WorkItems": [],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄと平行に取付けること",
"ﾌﾞﾗｹｯﾄ幅に対してｾﾝﾀｰ取付けの事",
"ﾌﾞﾗｹｯﾄより飛び出さ無い事"
],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼﾝｸﾞﾙﾓｰﾄﾞ原点ｾﾝｻ組立",
"WorkItems": [],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄと平行に取付けること",
"ﾌﾞﾗｹｯﾄ幅に対してｾﾝﾀｰ取付けの事",
"ﾌﾞﾗｹｯﾄより飛び出さ無い事"
],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTy... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "幅寄せ原点ｾﾝｻ組立",
"WorkItems": [
"1. BRACKET にSENSOR をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄと平行に取付けること"
],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ﾓｰﾄﾞ切替ｾﾝｻ組立",
"WorkItems": [
"1. BRACKET にSENSOR をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄと平行に取付けること"
],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾊﾟ―組立1",
"WorkItems": [
"◆1. CLAMPER PIN にｸﾞﾘｰｽを塗布する",
"2. 1完成品にCLAMPER をBOLT WASHER で取付ける"
],
"WorkPoints": [
"矢印方向に押し当ての事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1粒",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｸﾗﾝﾊﾟ―組立1",
"WorkItems": [
"◆1. CLAMPER PIN にｸﾞﾘｰｽを塗布する",
"2. 1完成品にCLAMPER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "1.94N･m",
"WorkName": "ｸﾗﾝﾊﾟ―組立2",
"WorkItems": [
"3. 2完成品の高さを調整する"
],
"WorkPoints": [
"基準:治具上面 73:5㎜",
"左右のﾎﾞﾙﾄで調整",
"右側規格値73.5㎜±0.02㎜",
"左側規格値73.5㎜±0.02㎜",
"中央規格値73.5㎜±0.03㎜"
],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｸﾗﾝﾌﾟﾌﾞﾚｰﾄﾞねじ高さ合わせ治具",
"Size": "",
"ToolOther": "FM-4086",
"WorkName": "ｸﾗﾝﾊﾟ―組立2",
"WorkItems": [
"2. 1完成品を治具に取付ける",
"3. 2完成品の高さを調整する"
],
"WorkPoints": [
"基準:治具上面 73:5㎜",
"左右のﾎﾞﾙﾄで調整",
"右側規格値73.5㎜±0.02㎜",
"左側規格値73.5㎜±0.02㎜",
"中央規格値73.5㎜±0.03㎜"
]... | {
"QualityItem": "設置確認",
"ToolManageNo": "FM-4086",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに設置してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾊﾟ―組立2",
"WorkItems": [
"3. 2完成品の高さを調整する"
],
"WorkPoints": [
"基準:治具上面 73:5㎜",
"左右のﾎﾞﾙﾄで調整",
"右側規格値73.5㎜±0.02㎜",
"左側規格値73.5㎜±0.02㎜",
"中央規格値73.5㎜±0.03㎜"
],
"Tolks": [
"締付ﾄﾙｸ 1.94N... | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "高さ:73.5㎜±0.02㎜73.5㎜±0.03㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C03",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾊﾟ―組立2",
"WorkItems": [
"1. ①にBOLT NUT を仮に取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを4個製作",
"15.5㎜"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:15.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾊﾟ―組立3",
"WorkItems": [
"1. ①にLABEL LABEL を貼付ける"
],
"WorkPoints": [
"ﾚｰﾝ1固定",
"ﾚｰﾝ2固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"6㎜",
"106㎜... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾊﾟ―組立4",
"WorkItems": [
"1. ①にLABEL LABEL LABEL LABEL LABEL を貼付ける"
],
"WorkPoints": [
"正流れ(左→右)",
"ｽﾗｲﾄﾞ搬送OP",
"逆流れ(右→左)",
"仕様確認の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾊﾟ―組立5",
"WorkItems": [
"1. ①にLABEL LABEL LABEL LABEL LABEL を貼付ける"
],
"WorkPoints": [
"ｽﾗｲﾄﾞ搬送OP",
"正流れ(左→右)",
"逆流れ(右→左)",
"仕様確認の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱｾﾝｻﾌﾞﾗｹｯﾄ組立ｼﾞｸﾞ(ﾋﾟｯﾁ9㎜)",
"Size": "",
"ToolOther": "FM-6502",
"WorkName": "基板ｾﾝｻ前組",
"WorkItems": [
"2. 1完成品にFIBER をはめ､NUT-PLATE を矢印方向に寄せBOLT BOLT WASHER で取付",
"1. ㉖にSPACER を入れる"
],
"WorkPoints": [
"FIBER の黒線側にのみ実施",
"ﾏｲﾅｽ溝を合わせる",
"FIBER のピンを㉖にはめる"
],... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6502",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "基板ｾﾝｻ前組",
"WorkItems": [
"2. 1完成品にFIBER をはめ､NUT-PLATE を矢印方向に寄せBOLT BOLT WASHER で取付"
],
"WorkPoints": [
"FIBER の黒線側にのみ実施",
"FIBER のピンを㉖にはめる"
],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo":... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3m",
"ToolOther": "",
"WorkName": "【OP切替仕様交換台車仕様出荷の場合】切替用ﾕﾆｯﾄ台車(駆動部用)梱包①",
"WorkItems": [
"1. ⑥を㉘㉙で保護し、BOX に㉙で固定する",
"2. 作業１完成品を㉘㉙で保護する"
],
"WorkPoints": [
"280㎜×200㎜",
"740㎜×400㎜",
"100㎜×100㎜を二つ折り"
],
"Tolks": [],
"InspectionNo": ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±10㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "",
"ToolOther": "",
"WorkName": "【OP切替仕様交換台車仕様出荷の場合】切替用ﾕﾆｯﾄ台車(駆動部用)梱包②",
"WorkItems": [
"1. ①に㉘を全体に巻く、または⑥を覆いかぶせ、㉗で固定する"
],
"WorkPoints": [
"対辺も同様に固定する事",
"ﾊﾝﾄﾞﾙを握っても袋が突っ張らないようにする事",
"袋を余りをまとめて固定する",
"㉘の場合㉗は不要"
],
"Tolks": [],
"Ins... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "",
"ToolOther": "",
"WorkName": "【OP切替仕様交換台車仕様出荷の場合】切替用ﾕﾆｯﾄ台車(支持部用)梱包",
"WorkItems": [
"1. ①を㉗㉘で保護する",
"2. ①に㉙を全体に巻く、または⑥を覆いかぶせ、㉘で固定する"
],
"WorkPoints": [
"740㎜×400㎜",
"対辺も同様に2か所",
"対辺も同様に3か所",
"ﾊﾝﾄﾞﾙを握っても袋が突っ張らないようにする事",
"袋を余りをまと... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3m",
"ToolOther": "",
"WorkName": "【OP切替仕様ﾄﾚｲ仕様出荷の場合】切替用ﾕﾆｯﾄ台車(駆動部用)梱包①",
"WorkItems": [
"1. BOX ⑥を㉗㉘で保護する",
"2. ①に作業１完成品を㉗㉙にて固定する",
"1. BOX ⑥を㉗㉘で保護する",
"2. ①に作業１完成品を㉗㉙にて固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"Inspe... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±10㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3m",
"ToolOther": "",
"WorkName": "【OP切替仕様ﾄﾚｲ仕様出荷の場合】切替用ﾕﾆｯﾄ台車(駆動部用)梱包②",
"WorkItems": [
"◆1. ①又は⑥の配線配管を㉗㉘で保護する",
"2. 保護した配線を㉘にてフレームに固定する"
],
"WorkPoints": [
"280㎜×200㎜",
"100㎜折り返し､ｺﾈｸﾀ部に重ねる",
"配線全体を覆うように巻き付け"
],
"Tolks": [],
"Insp... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±10㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "重量物運搬二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3m",
"ToolOther": "",
"WorkName": "【OP切替仕様ﾄﾚｲ仕様出荷の場合】切替用ﾕﾆｯﾄ台車(駆動部用)梱包③",
"WorkItems": [
"1. ①の板金・フレームを㉗㉘で保護する",
"◆2. ①に②を乗せ込み、㉗㉙にて固定する",
"1. ①の板金・フレームを㉗㉘で保護する",
"◆2. ①に②を乗せ込み、㉗㉙にて固定する"
],
"WorkPoints": [
"㉗400㎜×200㎜を巻き付け",
"㉗400㎜×200㎜... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±10㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "重量物運搬二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP切替仕様ﾄﾚｲ仕様出荷の場合】切替用ﾕﾆｯﾄ台車(駆動部用)梱包④",
"WorkItems": [
"1. ①に⑥を覆いかぶせ、㉖にて固定する"
],
"WorkPoints": [
"ﾊﾝﾄﾞﾙを握っても袋が突っ張らないようにする事",
"対辺側も同様に貼付け",
"余分な袋を部分を固定する",
"完成ｲﾒｰｼﾞ",
"出荷明細書を㉖で貼付ける"
],
"Tolks": [],
"In... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "-",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3m",
"ToolOther": "",
"WorkName": "【OP切替仕様ﾄﾚｲ仕様出荷の場合】切替用ﾕﾆｯﾄ台車(支持部用)梱包①",
"WorkItems": [
"1. ⑥を㉗㉘にて保護する",
"2. 作業１完成品を①に乗せ込み、㉗㉙にて固定する"
],
"WorkPoints": [
"1000㎜×600㎜",
"ﾊﾞﾝﾄﾞ:800㎜",
"100㎜×100㎜を二つ折り",
"ｷｽﾞ防止のため挟み込み"
],
"Tolks": [],... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±10㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3m",
"ToolOther": "",
"WorkName": "【OP切替仕様ﾄﾚｲ仕様出荷の場合】切替用ﾕﾆｯﾄ台車(支持部用)梱包②",
"WorkItems": [
"1. ①に㉗を敷いて、⑥を乗せ込み",
"2. ⑥を㉗㉘にて固定"
],
"WorkPoints": [
"740㎜×400㎜を二つ折り",
"ﾊﾞﾝﾄﾞ:500㎜",
"ﾊﾞﾝﾄﾞ400㎜",
"ｷｽﾞ防止のため挟み込み",
"ｷｽﾞ防止のため挟み込み",
"⑥の乗せ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±10㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3m",
"ToolOther": "",
"WorkName": "【OP切替仕様ﾄﾚｲ仕様出荷の場合】切替用ﾕﾆｯﾄ台車(支持部用)梱包③",
"WorkItems": [
"1. ⑥を㉗㉘にて保護する",
"2. ⑥を①に乗せ込み、㉙にて固定する",
"3. ①の側面を㉗㉘で保護する"
],
"WorkPoints": [
"740㎜×400㎜",
"200㎜×100㎜",
"740㎜×400㎜",
"対辺も同様に2か所",
"対辺も同様に... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±10㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3m",
"ToolOther": "",
"WorkName": "【OP切替仕様ﾄﾚｲ仕様出荷の場合】切替用ﾕﾆｯﾄ台車(支持部用)梱包④",
"WorkItems": [],
"WorkPoints": [
"①⑥重量物(13kg)運搬は二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"or",
"◆作業者安全作業"
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±10㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "重量物運搬二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "",
"ToolOther": "",
"WorkName": "【OP切替仕様ﾄﾚｲ仕様出荷の場合】切替用ﾕﾆｯﾄ台車(支持部用)梱包⑤",
"WorkItems": [
"1. ①に⑥を覆いかぶせ、㉗にて固定する"
],
"WorkPoints": [
"ﾊﾝﾄﾞﾙを握っても袋が突っ張らないようにする事",
"対辺側も同様に貼付け",
"余分な袋を部分を固定する",
"出荷明細書を㉗で貼付ける",
"完成ｲﾒｰｼﾞ"
],
"Tolks": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｼﾝ仕様確認",
"WorkItems": [
"2. 仕様書と実機が同じである事を確認し､検査表に記載する",
"1. S2出荷梱包ﾁｪｯｸﾘｽﾄを準備する"
],
"WorkPoints": [
"□にﾚを入れる",
"警告表示ﾗﾍﾞﾙの言語ｼｸﾞﾅﾙﾀﾜ-搬送高さ基板流れ方向塗装色本体構成ｵﾌﾟｼｮﾝ仕様",
"ver.1.00を使用すること"
],
"Tolks": [],
"Inspectio... | {
"QualityItem": "仕様確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "仕様書とﾏｼﾝが一致している事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A06",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｼﾝｼﾘｱﾙ・ｼｽﾃﾑﾊﾞｰｼﾞｮﾝ・製造年月日確認",
"WorkItems": [
"3. 『製造年月日』を登録する",
"1. 『ﾏｼﾝｼﾘｱﾙ番号』に入力されているｼﾘｱﾙNo.とﾏｼﾝに貼られているｼﾘｱﾙNo.が一致しているか確認",
"2. ｼｽﾃﾑﾊﾞｰｼﾞｮﾝ画面を画像保存し､ﾌｫｰﾏｯﾄﾌｧｲﾙに 貼付けし､ﾌﾟﾘﾝﾄｱｳﾄした用紙を添付する",
"4. 『製造年月日』が変更されている事を確認"
],
"Wor... | {
"QualityItem": "出荷ﾊﾞｰｼﾞｮﾝ確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A06",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｵﾌﾟｼｮﾝ設定確認1",
"WorkItems": [
"3. 『ﾍｯﾄﾞ』のｵﾌﾟｼｮﾝ設定が全て『OFF』になっている事を確認",
"1. 『全体』のｵﾌﾟｼｮﾝ設定が全て『OFF』(○が左側)になっている事を確認",
"2. 『XY軸』のｵﾌﾟｼｮﾝ設定が全て『OFF』(○が左側)になっている事を確認"
],
"WorkPoints": [
"技術指示を確認する事",
"技術指示を確認する事",
"技術指... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A06",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｵﾌﾟｼｮﾝ設定確認2",
"WorkItems": [
"1. 『ﾌｨｰﾀﾞｰ』のｵﾌﾟｼｮﾝ設定が全て『OFF』(○が左)になっている事を確認",
"2. 『ｺﾝﾍﾞﾔ』のｵﾌﾟｼｮﾝ設定が全て『OFF』になっている事を確認",
"3. 『ﾍｯﾄﾞｶﾒﾗ』のｵﾌﾟｼｮﾝ設定が全て『OFF』になっている事を確認",
"4. 『ﾏﾙﾁ認識ｶﾒﾗ』のｵﾌﾟｼｮﾝ設定が全て『OFF』になっている事を確認",
"5. ①(各ﾕﾆｯﾄ)内にあ... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A06",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷前準備(稼動情報・履歴ﾘｾｯﾄ)1",
"WorkItems": [
"1. 『稼働情報』をｸﾘｱする",
"3. 『真空ｾﾝｻｴﾗｰ履歴』をｸﾘｱする",
"2. 『停止履歴』をｸﾘｱする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEPJ-G002-A06",
"InspectionItems": [
"検査表①:出荷前確認",
"検査... | {
"QualityItem": "出荷前確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A06",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷前準備(ﾒﾝﾃﾅﾝｽ履歴確認)",
"WorkItems": [
"1. 『ﾒﾝﾃﾅﾝｽ履歴』が『0』である事を確認",
"2. 『消耗部品』の『稼働時間』が『0』である事を確認"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEPJ-G002-A06",
"InspectionItems": [
"検査表①:出荷前確認"
],
"WorkTypes"... | {
"QualityItem": "出荷前確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A06",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.