input stringclasses 1 value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "LCR計測ﾕﾆｯﾄ取付",
"WorkItems": [
"3. ②に2完成品をBOLT WASHER で取付"
],
"WorkPoints": [
"製造番号"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ｽﾋﾟｺﾝ取付",
"WorkItems": [
"1. VALVE にJOINT JOINT を取付",
"2. VALVE にJOINT を取付",
"3. SPEED-CONTROLLER を調整",
"4. BRACKET に3完成品をBOLT WASHER WASHER で取付"
],
"WorkPoints": [
"矢印方向に当てつけ",
"全閉から3.5回転でﾛｯｸ"
],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ｼﾞｮｲﾝﾄ取付け",
"WorkItems": [
"2. 1完成品を③にBOLT WASHER WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m以上",
"ToolOther": "",
"WorkName": "ｼﾞｮｲﾝﾄ取付け",
"WorkItems": [
"1. JOINT をJOINT に挿入",
"3. JOINT にTUBE を挿入"
],
"WorkPoints": [
"TUBE 長さ1200mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "圧入台",
"Size": "",
"ToolOther": "",
"WorkName": "ﾋﾟﾝ圧入・ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. BASE にPIN を圧入",
"2. 1完成品にCABLE-SUPPORT を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"出代:2mm"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾋﾟﾝ圧入・ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. BASE にPIN を圧入",
"2. 1完成品にCABLE-SUPPORT を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"出代:2mm"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "目安出代:2㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾋﾟﾝ圧入・ﾌﾞﾛｯｸ取付",
"WorkItems": [
"3. 2完成品にBRACKET をBOLT で取付"
],
"WorkPoints": [
"ﾋﾟﾝをはめてから取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "本体取付①",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"②は矢印方向に当てつけ"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "90cN･m",
"WorkName": "本体取付①",
"WorkItems": [
"2. 1完成品に③④をSCREW で取付"
],
"WorkPoints": [
"③④のｼﾞｮｲﾝﾄの向きに注意"
],
"Tolks": [
"締付ﾄﾙｸ 90cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "本体取付②",
"WorkItems": [
"1. ②に①をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "共通部取付",
"WorkItems": [
"1. ①に⑥をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FG端子にﾏｰｷﾝｸﾞﾀｲ取付",
"WorkItems": [
"1. ①にLABEL orLABEL からそれぞれに対応したﾏｰｷﾝｸﾞﾀｲを取付"
],
"WorkPoints": [
"取付けﾏｰｷﾝｸﾞﾀｲLABEL 前側:FGX201LABEL 後側:FGX203",
"取付けﾏｰｷﾝｸﾞﾀｲLABEL 前側:FGB4011LABEL 後側:FGB4012"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D13",
"InspectionItems": [
"検査表①:ﾏｰｷﾝｸﾞﾀｲ取付"
],
"WorkTypes": [],
"Words": [
"WETE-G002-D13"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D13",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FG線固定・ﾏｰｷﾝｸﾞﾀｲ取付",
"WorkItems": [
"1. ①のFG配線を被覆に固定",
"2. LABEL orLABEL を①の配線に取付"
],
"WorkPoints": [
"ｸﾞﾚｰ1本",
"ｸﾞﾚｰ2本",
"黒1本",
"取付ﾏｰｷﾝｸﾞﾀｲLABEL 前側:B1324RLABEL 後側:B1337R",
"取付ﾏｰｷﾝｸﾞﾀｲLABEL 前側:B1344RLABEL 後側:B1342R",
"取付けﾏｰｷﾝｸﾞﾀｲLABEL 前側:B1326RLABEL 後側:B1341R",
"文字方向は上図の方向とする事",
"文字方向は上図の方向とする",
"文字方向は上図の方向とする白ｲﾝｼｭﾛｯｸ側の配線に取付の事",
"被覆の中央付近"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"文字方向",
"文字方向",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"文字方向"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線接続①",
"WorkItems": [
"■2. 配線締結",
"1. ①に同軸ｹｰﾌﾞﾙ接続"
],
"WorkPoints": [
"取付ﾏｰｷﾝｸﾞﾀｲ前側:FGX201後側:FGX203",
"取付ﾏｰｷﾝｸﾞﾀｲ前側:FGB4011後側:FGB4012",
"ﾏｳﾝﾄに止める方は､細い配線で結束し無い事",
"Frontの場合は､SCREW Rearの場合は､SCREW ",
"ﾌﾟﾚｰﾄ側からL_CUR→L_POT→H_POT→H_CURの順で取付"
],
"Tolks": [
"締付ﾄﾙｸ 0.6N･m",
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WETE-G002-D13",
"InspectionItems": [
"検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認",
"検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"L_CUR",
"L_POT",
"H_POT",
"H_CUR",
"検査表①:ｺﾈｸﾀ接続確認",
"WETE-G002-D13"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D13",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "0.6N･m",
"WorkName": "配線接続①",
"WorkItems": [
"1. ①に同軸ｹｰﾌﾞﾙ接続"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄ側からL_CUR→L_POT→H_POT→H_CURの順で取付"
],
"Tolks": [
"締付ﾄﾙｸ 0.6N･m"
],
"InspectionNo": "WETE-G002-D13",
"InspectionItems": [
"検査表①:ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"L_CUR",
"L_POT",
"H_POT",
"H_CUR",
"■安全作業",
"WETE-G002-D13"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "0.6N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "WETE-G002-D13",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "配線接続①",
"WorkItems": [
"■2. 配線締結"
],
"WorkPoints": [
"取付ﾏｰｷﾝｸﾞﾀｲ前側:FGX201後側:FGX203",
"取付ﾏｰｷﾝｸﾞﾀｲ前側:FGB4011後側:FGB4012",
"ﾏｳﾝﾄに止める方は､細い配線で結束し無い事",
"Frontの場合は､SCREW Rearの場合は､SCREW "
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WETE-G002-D13",
"InspectionItems": [
"検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認",
"検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3m",
"ToolOther": "",
"WorkName": "配管準備",
"WorkItems": [
"1. TUBE を下記寸法にｶｯﾄ"
],
"WorkPoints": [
"両端に番号を記入する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管接続①",
"WorkItems": [
"1. ①に②を指定の場所に挿入"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B矢視",
"A矢視"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配管接続②",
"WorkItems": [
"1. ①に②を指定の場所に挿入"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線接続②",
"WorkItems": [
"1. ①にCABLE を接続",
"2. 1完成品を㉗で締結"
],
"WorkPoints": [
"○部に余裕を持たせて結束の事",
"ﾌﾞﾗｹｯﾄ端面より内側で締結の事",
"左から 『R4312･R4311･R4310 』 の順に取付",
"R4312",
"R4311",
"R4310",
"白線 ｺﾈｸﾀ元から260mmで固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "LCRﾁｪｯｸﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-5682",
"WorkName": "動作確認①",
"WorkItems": [
"1. 各配線･配管に治具ｺﾈｸﾀｰ差込み",
"2. 治具の電源･ｴｱｰを入れて､ｾﾝｻｰが点灯してる事を確認"
],
"WorkPoints": [
"ｸﾞﾚｰ2本の配線へ",
"ｸﾞﾚｰ1本の配線へ",
"黒1本の配線へ",
"PCへ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-5682",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "LCRﾁｪｯｸﾕﾆｯﾄﾁｪｯｶｰ(NPM-GH用)",
"Size": "",
"ToolOther": "FM-6074",
"WorkName": "動作確認①",
"WorkItems": [
"1. 各配線･配管に治具ｺﾈｸﾀｰ差込み",
"2. 治具の電源･ｴｱｰを入れて､ｾﾝｻｰが点灯してる事を確認"
],
"WorkPoints": [
"ｸﾞﾚｰ2本の配線へ",
"ｸﾞﾚｰ1本の配線へ",
"黒1本の配線へ",
"PCへ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-6074",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "LCRﾁｪｯｸﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-5682",
"WorkName": "動作確認②",
"WorkItems": [
"1. 検査用ｱﾌﾟﾘ(LCRunit_test.exe)を起動",
"2. 検査表に従い､検査を行う",
"3. 動作確認終了後､検査治具の電源･ｴｱｰを外す"
],
"WorkPoints": [
"下図の通りになっていること(検査項目･検査値が全て緑になっている事)"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D13",
"InspectionItems": [
"検査表①:計測ﾕﾆｯﾄの機能検査"
],
"WorkTypes": [],
"Words": [
"WETE-G002-D13"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-5682",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D13",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "LCRﾁｪｯｸﾕﾆｯﾄﾁｪｯｶｰ(NPM-GH用)",
"Size": "",
"ToolOther": "FM-6074",
"WorkName": "動作確認②",
"WorkItems": [
"1. 検査用ｱﾌﾟﾘ(LCRunit_test.exe)を起動",
"2. 検査表に従い､検査を行う",
"3. 動作確認終了後､検査治具の電源･ｴｱｰを外す"
],
"WorkPoints": [
"下図の通りになっていること(検査項目･検査値が全て緑になっている事)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:計測ﾕﾆｯﾄの機能検査"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-6074",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "払い出し部品",
"WorkItems": [
"1. 次工程に払い出し"
],
"WorkPoints": [
"LABEL LABEL LABEL LABEL はLCRﾒｰﾀ設置(NPM-GW)組立へ払い出し",
"CABLE CABLE CABLE CABLE はB1工程に払い出し"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾑﾌｫﾛｱ部組立",
"WorkItems": [
"1. BRACKET の取付面(青色部)に砥石を掛ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5㎜(BOX)",
"ToolOther": "150cN･m",
"WorkName": "ｶﾑﾌｫﾛｱ部組立",
"WorkItems": [
"2. 1完成品にCAM-FOLLOWER をWASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"CAM-FOLLOWER の付属ﾅｯﾄは廃棄して下さい"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙﾐ用砥石",
"Size": "",
"ToolOther": "ｽｰﾊﾟｰｼｬｲﾅｰ砥石",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備",
"WorkItems": [
"1. PLATE の両面に㉖を掛ける"
],
"WorkPoints": [
"表面(座ｸﾞﾘ有)は特に表面に傷がつかない様に注意する事",
"PLATE に打痕やﾊﾞﾘが無い事",
"緑色部の9箇所を測定する事(平面度:0.1㎜以内)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備",
"WorkItems": [
"1. PLATE の両面に㉖を掛ける"
],
"WorkPoints": [
"表面(座ｸﾞﾘ有)は特に表面に傷がつかない様に注意する事",
"PLATE に打痕やﾊﾞﾘが無い事",
"緑色部の9箇所を測定する事(平面度:0.1㎜以内)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.1㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①",
"WorkItems": [
"2. ①にBRACKET WASHER をBOLT で取付ける",
"1. BRACKET に㉖油砥石を掛ける"
],
"WorkPoints": [
"BRACKET の全面にﾊﾞﾘ､打痕等ないか確認する事",
"①とBRACKET の間にWASHER を挿入する事",
"BRACKET を㉗の青点線部に押し当てて取付ける事",
"青色部に㉖を掛ける"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①",
"WorkItems": [
"2. ①にBRACKET WASHER をBOLT で取付ける",
"1. BRACKET に㉖油砥石を掛ける"
],
"WorkPoints": [
"BRACKET の全面にﾊﾞﾘ､打痕等ないか確認する事",
"①とBRACKET の間にWASHER を挿入する事",
"BRACKET を㉗の青点線部に押し当てて取付ける事",
"青色部に㉖を掛ける"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①",
"WorkItems": [
"2. ①にBRACKET WASHER をBOLT で取付ける",
"1. BRACKET に㉖油砥石を掛ける"
],
"WorkPoints": [
"BRACKET の全面にﾊﾞﾘ､打痕等ないか確認する事",
"①とBRACKET の間にWASHER を挿入する事",
"BRACKET を㉗の青点線部に押し当てて取付ける事",
"青色部に㉖を掛ける"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②",
"WorkItems": [
"1. ①に②をBOLT で取付ける"
],
"WorkPoints": [
"②を㉘の青点線部に押し当てて取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②",
"WorkItems": [
"1. ①に②をBOLT で取付ける"
],
"WorkPoints": [
"②を㉘の青点線部に押し当てて取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"青色部に㉖を掛ける（面取りが無い側）",
"BLOCK の面取り位置を図左手前にして取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"青色部に㉖を掛ける（面取りが無い側）",
"BLOCK の面取り位置を図左手前にして取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"青色部に㉖を掛ける（面取りが無い側）",
"BLOCK の面取り位置を図左手前にして取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-④",
"WorkItems": [
"1. ①にGUIDE をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"GUIDE は各々外側(矢印方向)に寄せて取付ける事(傾き無き事)"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾑﾌｫﾛｱ部組立",
"WorkItems": [
"1. BRACKET の取付面(青色部)に砥石を掛ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを4個製作"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5㎜(BOX)",
"ToolOther": "150cN･m",
"WorkName": "ｶﾑﾌｫﾛｱ部組立",
"WorkItems": [
"2. 1完成品にCAM-FOLLOWER をWASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"CAM-FOLLOWER の付属ﾅｯﾄは廃棄して下さい"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙﾐ用砥石",
"Size": "",
"ToolOther": "ｽｰﾊﾟｰｼｬｲﾅｰ砥石",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備",
"WorkItems": [
"1. PLATE の両面に㉖を掛ける"
],
"WorkPoints": [
"表面(座ｸﾞﾘ有)は特に表面に傷がつかない様に注意する事",
"PLATE に打痕やﾊﾞﾘが無い事",
"緑色部の9箇所を測定する事(平面度:0.1㎜以内)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"表 面"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備",
"WorkItems": [
"1. PLATE の両面に㉖を掛ける"
],
"WorkPoints": [
"表面(座ｸﾞﾘ有)は特に表面に傷がつかない様に注意する事",
"PLATE に打痕やﾊﾞﾘが無い事",
"緑色部の9箇所を測定する事(平面度:0.1㎜以内)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"表 面"
]
} | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.1㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①",
"WorkItems": [],
"WorkPoints": [
"①とBRACKET の間にWASHER を挿入する事",
"BRACKET を㉗の青点線部に押し当てて取付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①",
"WorkItems": [
"2. ①にBRACKET WASHER をBOLT で取付ける",
"1. BRACKET に㉖油砥石を掛ける"
],
"WorkPoints": [
"BRACKET の全面にﾊﾞﾘ､打痕等ないか確認する事",
"青色部に㉖を掛ける"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-5626"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①",
"WorkItems": [
"2. ①にBRACKET WASHER をBOLT で取付ける",
"1. BRACKET に㉖油砥石を掛ける"
],
"WorkPoints": [
"BRACKET の全面にﾊﾞﾘ､打痕等ないか確認する事",
"青色部に㉖を掛ける"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-5626"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②",
"WorkItems": [
"1. ①に②をBOLT で取付ける"
],
"WorkPoints": [
"2箇所の取付調整を行う事",
"②を㉘の青点線部に押し当てて取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②",
"WorkItems": [
"1. ①に②をBOLT で取付ける"
],
"WorkPoints": [
"2箇所の取付調整を行う事",
"②を㉘の青点線部に押し当てて取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"青色部に㉖を掛ける（面取りが無い側）",
"BLOCK の面取り位置を図左手前にして取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"青色部に㉖を掛ける（面取りが無い側）",
"BLOCK の面取り位置を図左手前にして取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"青色部に㉖を掛ける（面取りが無い側）",
"BLOCK の面取り位置を図左手前にして取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-④",
"WorkItems": [
"1. ①にGUIDE をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"GUIDE は各々外側(矢印方向)に寄せて取付ける事(傾き無き事)"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "交換台車支持部組立(左)1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "PIN出代:4㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "13㎜BOX",
"ToolOther": "12.7N･m",
"WorkName": "交換台車支持部組立(左)1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "12.7N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "26.5N･m",
"WorkName": "交換台車支持部組立(左)2",
"WorkItems": [
"1. ①にCAM-FOLLOWER を取付ける"
],
"WorkPoints": [
"付属ﾅｯﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 26.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.5N･m",
"WorkName": "交換台車支持部組立(左)2",
"WorkItems": [
"2. 1完成品にGUIDE をSPACER BOLT WASHER WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20N･m",
"WorkName": "交換台車支持部組立(左)3",
"WorkItems": [
"1. ①にFRAME(L) BLOCK をBOLT で取付ける"
],
"WorkPoints": [
"当付け方向",
"当付け方向"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "交換台車支持部組立(左)4",
"WorkItems": [
"1. BRACKET にGUIDE をSPACER BOLT WASHER WASHER で取付ける",
"2. 1完成品をBRACKET にBOLT WASHER 、BOLT ㉒で取付ける"
],
"WorkPoints": [
"面位置",
"矢印方向に押し当てて取付ける",
"前側取付位置",
"後側取付位置",
"長穴ｾﾝﾀｰに合せる"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "5.3N･m",
"WorkName": "交換台車支持部組立(左)4",
"WorkItems": [
"1. BRACKET にGUIDE をSPACER BOLT WASHER WASHER で取付ける",
"2. 1完成品をBRACKET にBOLT WASHER 、BOLT ㉒で取付ける"
],
"WorkPoints": [
"前側取付位置",
"後側取付位置",
"長穴ｾﾝﾀｰに合せる"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.3N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "交換台車支持部組立(左)5",
"WorkItems": [
"1. ①にCOVER をBOLT WASHER で取付ける"
],
"WorkPoints": [
"台車仕様",
"台車仕様"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"前側取付位置",
"後側取付位置"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "交換台車支持部組立(左)6",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"面位置合せ"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20N･m",
"WorkName": "交換台車支持部組立(左)7",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"矢印方向に押し当てて取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "交換台車支持部組立(左)8ｽﾙｰ部品",
"WorkItems": [
"1. 次工程へ払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｶﾞｲﾄﾞ組立30連/60連(前側&左側)1",
"WorkItems": [
"1. BRACKET にGUIDE をSPACER BOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"平行に取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｶﾞｲﾄﾞ組立30連/60連(前側&左側)2",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品30連/60連(前側&左側)",
"WorkItems": [
"1. H1工程へ払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. COVER COVER BUSH を指定の長さに切断する",
"2. 1の完成品をBRACKET へ貼付ける",
"1. COVER COVER BUSH を指定の長さに切断する",
"2. 1の完成品をBRACKET へ貼付ける"
],
"WorkPoints": [
"COVER ⇒32㎜;8本",
"COVER ⇒21㎜;4本",
"BUSH ⇒16㎜;2本",
"COVER ⇒32㎜;8本",
"COVER ⇒21㎜;4本",
"BUSH ⇒16㎜;2本"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｴｯｼﾞｶﾊﾞｰの角と角を合わせる",
"この作業では同じものを2個製作",
"ｴｯｼﾞｶﾊﾞｰの角と角を合わせる",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｴｯｼﾞｶﾊﾞｰの角と角を合わせる"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ組立",
"WorkItems": [
"2. 1の完成品をGUIDE へ貼付け、㉘をセットする",
"1. COVER を指定の長さに切断する"
],
"WorkPoints": [
"105㎜;2本"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"COVER がR部にかからない様に貼付け",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗﾘﾝｸｹｰﾌﾞﾙ中継ﾕﾆｯﾄ組立",
"WorkItems": [
"2. 1の完成品へBRACKET をBOLT WASHER NUT で取付ける",
"3. 2の完成品に㉛を３本通す",
"◆1. PLATE へBUSH を貼付ける"
],
"WorkPoints": [
"R部は入念に押し付け貼付ける事",
"取付けは端面方向へ押し付ける事",
"約半分通し､縛ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"BUSH を下図の様に変形する",
"3ｺﾏ",
"2ｺﾏ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｶﾒﾗﾘﾝｸｹｰﾌﾞﾙ中継ﾕﾆｯﾄ組立",
"WorkItems": [
"2. 1の完成品へBRACKET をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"取付けは端面方向へ押し付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"3ｺﾏ",
"2ｺﾏ",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "治具",
"Size": "",
"ToolOther": "FM-6631",
"WorkName": "Y軸ﾍﾞｱﾀﾞｸﾄ組立",
"WorkItems": [
"1. DUCT へSHEET を貼付ける",
"2. 1の完成品へSHEET を貼付ける",
"▲◆3. 2の完成品へWASHER を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"SHEET を㉗へ押し付け",
"SHEET を㉗へ押し付け",
"SHEET を㉗へ押し付け",
"開口部端面合わせ",
"㉗押し付け",
"Dｶｯﾄ",
"SHEET を㉗へ押し付け",
"SHEET を㉗へ押し付け",
"SHEET を㉗へ押し付け",
"㉗取付け方向",
"開口部端面合わせ",
"DUCT の穴とWASHER の穴を合わせる",
"この作業では同じものを2個製作",
"接着剤塗布 ｺﾞﾏ粒:各1",
"治具移動",
"治具移動"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6631",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾍﾞｱﾀﾞｸﾄ組立",
"WorkItems": [
"1. DUCT へSHEET を貼付ける",
"2. 1の完成品へSHEET を貼付ける",
"▲◆3. 2の完成品へWASHER を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"SHEET を㉗へ押し付け",
"SHEET を㉗へ押し付け",
"SHEET を㉗へ押し付け",
"開口部端面合わせ",
"㉗押し付け",
"Dｶｯﾄ",
"SHEET を㉗へ押し付け",
"SHEET を㉗へ押し付け",
"SHEET を㉗へ押し付け",
"㉗取付け方向",
"開口部端面合わせ",
"DUCT の穴とWASHER の穴を合わせる",
"この作業では同じものを2個製作",
"接着剤塗布 ｺﾞﾏ粒:各1",
"治具移動",
"治具移動"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒;各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ415",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾍﾞｱﾀﾞｸﾄ組立",
"WorkItems": [
"1. DUCT へSHEET を貼付ける",
"2. 1の完成品へSHEET を貼付ける",
"▲◆3. 2の完成品へWASHER を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"SHEET を㉗へ押し付け",
"SHEET を㉗へ押し付け",
"SHEET を㉗へ押し付け",
"開口部端面合わせ",
"㉗押し付け",
"Dｶｯﾄ",
"SHEET を㉗へ押し付け",
"SHEET を㉗へ押し付け",
"SHEET を㉗へ押し付け",
"㉗取付け方向",
"開口部端面合わせ",
"DUCT の穴とWASHER の穴を合わせる",
"この作業では同じものを2個製作",
"接着剤塗布 ｺﾞﾏ粒:各1",
"治具移動",
"治具移動"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LED照明制御ﾎﾞｰﾄﾞ準備",
"WorkItems": [
"★2. Dip-SW8番をONにする",
"★1. LED LIGHTING CONTROL BOARD orLED LIGHTING CONTROL BOARD へCABLE を接続する"
],
"WorkPoints": [
"CN15､CN19に接続する",
"仕様員数通り(標準ﾍｯﾄﾞｶﾒﾗ､文字認識ﾍｯﾄﾞｶﾒﾗ)に制作する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN15",
"Dip-SW 8",
"CN19",
"or"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸F側配線ｺﾈｸﾀ接続",
"WorkItems": [
"■1. XY-AXIS FRONT SIDE WIRING:NPM-GW へ⑥を接続する",
"■2. 1の完成品へ⑦を接続する"
],
"WorkPoints": [
"⑥のｻｲｽﾞに注意する事(ｺﾈｸﾀ幅;20㎜)",
"差込み治具は使用後､取り外す事",
"⑦のｻｲｽﾞに注意する事(ｺﾈｸﾀ幅;25㎜)",
"差込み治具は使用後､取り外す事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D04",
"InspectionItems": [
"検査表XY-AXIS FRONT SIDE WIRING:NPM-GW :2.ﾄﾞﾗｲﾊﾞ設定(3)ｺﾈｸﾀ端子接続",
"検査表XY-AXIS FRONT SIDE WIRING:NPM-GW :2.ﾄﾞﾗｲﾊﾞ設定(3)ｺﾈｸﾀ端子接続"
],
"WorkTypes": [],
"Words": [
"V(A)K502",
"U(A)K502",
"UK501",
"VK501",
"幅;20mm",
"銘板",
"WK501",
"X軸 ﾄﾞﾗｲﾊﾞ付属品",
"Y軸 ﾄﾞﾗｲﾊﾞ付属品",
"Y軸 ﾄﾞﾗｲﾊﾞ付属品",
"幅;25mm",
"幅;25mm",
"W(A)K502",
"V(B)K502",
"U(B)K502",
"W(B)K502",
"端子凸凹面",
"銘板",
"端子凸凹面",
"⑥はB1工程前準備より受け取る",
"⑦はB1工程前準備より受け取る",
"･端子凸凹面をｺﾈｸﾀの銘板側に向け､奥まで挿入する事･挿入後､ｹｰﾌﾞﾙを引っ張り抜け無い事",
"･端子凸凹面をｺﾈｸﾀの銘板側に向け､奥まで挿入する事･挿入後､ｹｰﾌﾞﾙを引っ張り抜け無い事",
"WETE-G002-D04"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸R側配線ｺﾈｸﾀ接続",
"WorkItems": [
"■1. XY-AXIS REAR SIDE WIRING:NPM-GW へ⑥を接続する",
"■2. 1の完成品へ⑦を接続する"
],
"WorkPoints": [
"⑥のｻｲｽﾞに注意する事(ｺﾈｸﾀ幅;20㎜)",
"差込み治具は使用後､取り外す事",
"差込み治具は使用後､取り外す事",
"⑦のｻｲｽﾞに注意する事(ｺﾈｸﾀ幅;25㎜)"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D04",
"InspectionItems": [
"検査表XY-AXIS REAR SIDE WIRING:NPM-GW :2.ﾄﾞﾗｲﾊﾞ設定(3)ｺﾈｸﾀ端子接続",
"検査表XY-AXIS REAR SIDE WIRING:NPM-GW :2.ﾄﾞﾗｲﾊﾞ設定(3)ｺﾈｸﾀ端子接続"
],
"WorkTypes": [],
"Words": [
"V(A)K504",
"U(A)K504",
"UK503",
"VK503",
"幅;20mm",
"WK503",
"X軸 ﾄﾞﾗｲﾊﾞ付属品",
"Y軸 ﾄﾞﾗｲﾊﾞ付属品",
"Y軸 ﾄﾞﾗｲﾊﾞ付属品",
"幅;25mm",
"幅;25mm",
"W(A)K504",
"V(B)K504",
"U(B)K504",
"W(B)K504",
"端子の凹凸面にする",
"銘板",
"端子凸凹面",
"端子の凹凸面にする",
"銘板",
"端子凸凹面",
"⑥はB1工程前準備より受け取る",
"⑦はB1工程前準備より受け取る",
"･端子凸凹面をｺﾈｸﾀの銘板側に向け､奥まで挿入する事･挿入後､ｹｰﾌﾞﾙを引っ張り抜け無い事",
"･端子凸凹面をｺﾈｸﾀの銘板側に向け､奥まで挿入する事･挿入後､ｹｰﾌﾞﾙを引っ張り抜け無い事",
"WETE-G002-D04"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "WETE-G002-D04",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "銘板・警告ﾗﾍﾞﾙ貼付(ﾏｸﾞﾈｯﾄｶﾊﾞｰ)",
"WorkItems": [
"2. COVER へLABEL を貼付ける(左前､右奥)",
"1. COVER へLABEL を貼付ける(右前､左奥)",
"2. COVER へLABEL を貼付ける(左前､右奥)",
"1. COVER へLABEL を貼付ける(右前､左奥)"
],
"WorkPoints": [
"貼付け面に注意!この部品には方向性があります",
"貼付け面に注意!この部品には方向性があります"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"下面合わせ",
"200mm",
"下面合わせ",
"この作業では同じものを2個製作",
"この作業では同じものを2個製作",
"下面合わせ",
"200mm",
"下面合わせ",
"この作業では同じものを2個製作",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板・警告ﾗﾍﾞﾙ貼付(ﾍｯﾄﾞ部ｶﾊﾞｰ)",
"WorkItems": [
"1. COVER へLABEL LABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"17mm",
"4mm",
"1mm",
"17mm",
"4mm"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品準備(本体ﾕﾆｯﾄ)",
"WorkItems": [
"1. 次工程に払い出す"
],
"WorkPoints": [
"員数を確認する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品準備(XYﾕﾆｯﾄ)①",
"WorkItems": [
"1. 次工程に払い出す"
],
"WorkPoints": [
"員数を確認する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品準備(XYﾕﾆｯﾄ)②",
"WorkItems": [
"1. 次工程に払い出す"
],
"WorkPoints": [
"員数を確認する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品準備(標準ﾍｯﾄﾞｶﾒﾗ)",
"WorkItems": [
"1. 次工程に払い出す"
],
"WorkPoints": [
"仕様の員数通りに払い出しする事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品準備(文字認識対応ﾍｯﾄﾞｶﾒﾗ)",
"WorkItems": [
"1. 次工程に払い出す"
],
"WorkPoints": [
"OP;高さｾﾝｻ仕様がある場合はCLIP BOLT 払出不要",
"仕様の員数通りに払い出しする事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾎﾟｽﾄ組立",
"WorkItems": [
"1. SPACER にSCREW を取付",
"2. SPACER にCABLE-SUPPORT をBOLT で仮取付",
"3. 2完成品にSCREW を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"11㎜",
"仮止め:全体ｶﾊﾞｰ取付工程にて本締め"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "11㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "束線用配線ﾏｰｷﾝｸﾞ",
"WorkItems": [
"1. CABLE の配線を指示通りの位置にﾏｰｷﾝｸﾞをする"
],
"WorkPoints": [
"200㎜",
"670㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "束線前準備",
"WorkItems": [
"1. ①にCABLE CABLE CABLE を追加･固定し､CABLE CABLE を接続する"
],
"WorkPoints": [
"B1115RB1243R",
"FT11",
"B1325R",
"B1340R",
"ﾌﾛﾝﾄ側",
"ﾘｱ側",
"①黄色ﾏｰｷﾝｸﾞを束線の白ｲﾝｼｭﾛｯｸに合わせる",
"CART.F1P1 他"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"CNCOV/CN31/CNCLR/CNTCRK351",
"CNIOA/CN32/CNSPOT1K351",
"B1324P/B1325P/B1326P/B1344P/1R4310P",
"B1337P/B1340P/B1341P/B1342P/1R4345P",
"DX122",
"LCVLIOK351",
"余長はここでまとめる",
"ｲﾝｼｭﾛｯｸ(200mm)",
"ｲﾝｼｭﾛｯｸ(200mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"検査表①:LCR5.LCR計測ﾕﾆｯﾄ部ｺﾈｸﾀ接続確認"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "束線前準備",
"WorkItems": [
"1. ①にCABLE CABLE CABLE を追加･固定し､CABLE CABLE を接続する"
],
"WorkPoints": [
"B1115RB1243R",
"FT11",
"B1325R",
"B1340R",
"ﾌﾛﾝﾄ側",
"ﾘｱ側",
"①黄色ﾏｰｷﾝｸﾞを束線の白ｲﾝｼｭﾛｯｸに合わせる",
"CART.F1P1 他"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表①:LCR5.LCR計測ﾕﾆｯﾄ部ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"CNCOV/CN31/CNCLR/CNTCRK351",
"CNIOA/CN32/CNSPOT1K351",
"B1324P/B1325P/B1326P/B1344P/1R4310P",
"B1337P/B1340P/B1341P/B1342P/1R4345P",
"DX122",
"LCVLIOK351",
"余長はここでまとめる",
"ｲﾝｼｭﾛｯｸ(200mm)",
"ｲﾝｼｭﾛｯｸ(200mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"WETE-G002-A03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "7㎜BOX",
"ToolOther": "194cN･m",
"WorkName": "ﾘﾝｸﾞI/O負荷基板取付け",
"WorkItems": [
"1. 本体にSPACER を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"★静電対策作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾘﾝｸﾞI/O負荷基板取付け",
"WorkItems": [
"★2. 1完成品に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"『3』を確認する"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表SPACER :IO1. ﾘﾝｸﾞI/O基板ｺﾈｸﾀ接続確認",
"★静電対策作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾝｸﾞI/O負荷基板取付け",
"WorkItems": [
"3. LABEL を貼付ける",
"1. 本体にSPACER を取付ける",
"★2. 1完成品に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"『3』を確認する",
"5㎜",
"58㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表SPACER :IO1. ﾘﾝｸﾞI/O基板ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"REAR",
"WETE-G002-A03"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "LCRﾒｰﾀｰ取付け",
"WorkItems": [
"1. 本体にCOLLAR をBOLT WASHER で取付ける",
"2. 本体に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"前作業にて取付けたｶﾗｰ部に挿入する"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "精密ﾏｲﾅｽ",
"ToolOther": "15cN･m",
"WorkName": "ｶﾒﾗﾘﾝｸｹｰﾌﾞﾙ接続",
"WorkItems": [
"■1. ①②をLCRﾒｰﾀｰに接続する"
],
"WorkPoints": [
"仕様により接続本数が違います",
"前側のみ仕様時",
"後側のみ仕様時",
"CH1B4010",
"CH2B4010",
"CH2B4010",
"CH1B4010",
"前後仕様時"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表①:LCR2.LCRﾒｰﾀｰ部ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"FRONT",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:LCR3.LCRﾒｰﾀｰ部ﾈｼﾞ締め付けﾄﾙｸ確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗﾘﾝｸｹｰﾌﾞﾙ接続",
"WorkItems": [
"■1. ①②をLCRﾒｰﾀｰに接続する"
],
"WorkPoints": [
"仕様により接続本数が違います",
"前側のみ仕様時",
"後側のみ仕様時",
"CH1B4010",
"CH2B4010",
"CH2B4010",
"CH1B4010",
"前後仕様時"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表①:LCR3.LCRﾒｰﾀｰ部ﾈｼﾞ締め付けﾄﾙｸ確認"
],
"WorkTypes": [],
"Words": [
"FRONT",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:LCR2.LCRﾒｰﾀｰ部ｺﾈｸﾀ接続確認",
"WETE-G002-A03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し①",
"WorkItems": [
"1. 各配線を引き回し､固定する"
],
"WorkPoints": [
"ﾘｱ側へLCRLAN",
"ﾘｱ側へEX122CONTB4012",
"ﾌﾛﾝﾄ側へLCRUSBCONTB4011"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "25cN･m",
"WorkName": "配線引き回し②",
"WorkItems": [
"1. 配線を引き回し･固定し､USBｺﾈｸﾀをBOLT WASHER で取付ける"
],
"WorkPoints": [
"B1324/5/6P/B1344P/1R4310P抜き穴から出さない",
"CONTB4011抜き穴から出さない",
"LCRUSB",
"抜き穴から外側へ",
"取付け方向に注意すること"
],
"Tolks": [
"締付ﾄﾙｸ 25cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"FRONT",
"検査表①:LCR4.ﾌﾞﾗｹｯﾄ部接続確認(F/R共通)",
"ｲﾝｼｭﾛｯｸ(200mm)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "25cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し②",
"WorkItems": [
"1. 配線を引き回し･固定し､USBｺﾈｸﾀをBOLT WASHER で取付ける"
],
"WorkPoints": [
"B1324/5/6P/B1344P/1R4310P抜き穴から出さない",
"CONTB4011抜き穴から出さない",
"LCRUSB",
"抜き穴から外側へ",
"取付け方向に注意すること"
],
"Tolks": [
"締付ﾄﾙｸ 25cN･m"
],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表①:LCR4.ﾌﾞﾗｹｯﾄ部接続確認(F/R共通)"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"FRONT",
"ｲﾝｼｭﾛｯｸ(200mm)",
"WETE-G002-A03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾝｸﾞI/O負荷基板配線接続・引き回し",
"WorkItems": [
"★1. 配線を引き回しｺﾈｸﾀ･ﾌｧｲﾊﾞｰ線を接続する"
],
"WorkPoints": [
"LCVLIOK351",
"前側より EX122",
"DX122",
"EX122",
"前側より CONTB4012架台左後側へ",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること",
"3K351",
"4K351",
"基板へのﾌｧｲﾊﾞｰ線余長を固定する"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表①:IO1. ﾘﾝｸﾞI/O基板ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"REAR",
"CNTCRK351",
"CNSPOT1K351",
"CNIOAK351",
"CN32K351",
"CNCOVK351",
"CNCLRK351",
"CN31K351",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(150mm)",
"検査表①:IO2.ﾊﾟﾜｰﾕﾆｯﾄ部ｺﾈｸﾀ接続確認",
"F側LCRﾁｪｯｶｰ仕様時接続",
"検査表①:LCR1. ﾊﾟﾜｰﾕﾆｯﾄ部ｺﾈｸﾀ接続確認",
"R側LCRﾁｪｯｶｰ仕様時接続",
"ｲﾝｼｭﾛｯｸ(100mm)",
"WETE-G002-A03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し③",
"WorkItems": [
"1. 各配線を引き回し､固定する"
],
"WorkPoints": [
"B1337P/B1340/1/2P/1R4345P抜き穴から出さない",
"CONTB4012抜き穴から出さない",
"LCRﾁｪｯｶｰ R側仕様時のみ作業実施"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"REAR",
"ｲﾝｼｭﾛｯｸ(300mm)"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し④",
"WorkItems": [
"1. 各配線を引き回し､固定する"
],
"WorkPoints": [
"前側より LCRLAN連結ﾌﾞﾗｹｯﾄへ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"REAR"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し⑤",
"WorkItems": [
"1. 配線を引き回し､固定する"
],
"WorkPoints": [
"LCRLAN中継ｺﾈｸﾀへ挿入する",
"LCRUSB",
"余長をここで丸めて配管に固定する",
"余長を丸めて固定する"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表①:LCR4.ﾌﾞﾗｹｯﾄ部接続確認(F/R共通)"
],
"WorkTypes": [],
"Words": [
"FRONT",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(300mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(100mm)",
"WETE-G002-A03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.