Datasets:
ayuzawa
/
ManageProcess20

Dataset card Data Studio Files
xet
Community
1
input
stringclasses
1 value
instruction
stringlengths
222
3.65k
output
stringlengths
193
367
category
stringclasses
1 value
index
stringclasses
1 value
fileName
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "7㎜", "ToolOther": "1.9N･m", "WorkName": "固定側ｸﾗﾝﾊﾟ―組立2", "WorkItems": [ "3. 2完成品の高さを調整する", "1. ①②にBOLT NUT を仮取付" ], "WorkPoints": [ "左側規格値73.5㎜±0.02㎜", "中央規格値73.5㎜±0.03㎜", "ﾅｯﾄの向きに注意" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを各2個製作", "検査表①:基板ｸﾗﾝﾊﾟｰ高さ調整" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "1.9N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "1/100", "ToolOther": "", "WorkName": "固定側ｸﾗﾝﾊﾟ―組立2", "WorkItems": [ "3. 2完成品の高さを調整する", "1. ①②にBOLT NUT を仮取付" ], "WorkPoints": [ "左側規格値73.5㎜±0.02㎜", "中央規格値73.5㎜±0.03㎜", "ﾅｯﾄの向きに注意" ], "Tolks": [], "InspectionNo": "WETE-G002-C04", "InspectionItems": [ "検査表①:基板ｸﾗﾝﾊﾟｰ高さ調整" ], "WorkTypes": [], "Words": [ "この作業では同じものを各2個製作", "WETE-G002-C04" ] }
{ "QualityItem": "高さ確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "左右:±0.02㎜以内中央部:±0.03㎜以内", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WETE-G002-C04", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(ｺﾝﾍﾞﾔｰ)", "Size": "", "ToolOther": "FM-6621", "WorkName": "固定側ｸﾗﾝﾊﾟ―組立3", "WorkItems": [ "1. ①にLABEL を貼付ける" ], "WorkPoints": [ "ﾚｰﾝ1固定", "ﾚｰﾝ2固定", "①に㉗をピンク色矢印方向に押し当て", "貼付前に㉖にて貼付部分を清掃する事", "LABEL を㉗に青色矢印方向に合わせて貼付け" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "㉗固定側・可動側クランパ―" ] }
{ "QualityItem": "貼付確認", "ToolManageNo": "FM-6621", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り貼付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "可動側ｸﾗﾝﾊﾟ―組立1", "WorkItems": [ "3. 2完成品にCLAMPER CLAMPER をBOLT で取付", "◆2. 1完成品とPIN にｸﾞﾘｰｽを塗布", "1. CLAMPER CLAMPER にｱﾙｶﾝｻｽをかける" ], "WorkPoints": [ "矢印方向に押し当ての事", "CLAMPER CLAMPER PIN 取付面にｱﾙｶﾝｻｽをかける" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを各2個製作", "ｸﾞﾘｰｽ塗布 米粒:各1" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "米粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "可動側ｸﾗﾝﾊﾟ―組立1", "WorkItems": [ "3. 2完成品にCLAMPER CLAMPER をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "◆作業者安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｱﾙｶﾝｻｽ", "Size": "", "ToolOther": "", "WorkName": "可動側ｸﾗﾝﾊﾟ―組立1", "WorkItems": [ "◆2. 1完成品とPIN にｸﾞﾘｰｽを塗布", "1. CLAMPER CLAMPER にｱﾙｶﾝｻｽをかける" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを各2個製作", "ｸﾞﾘｰｽ塗布 米粒:各1", "◆作業者安全作業" ] }
{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ﾊﾞﾘ等無い事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "可動側ｸﾗﾝﾊﾟ―組立2", "WorkItems": [ "2. 1完成品を㉘に取付", "1. ①②にBOLT NUT を仮取付" ], "WorkPoints": [ "17.5mm", "ﾅｯﾄの向きに注意" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものを各2個製作" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｸﾗﾝﾌﾟﾌﾞﾚｰﾄﾞねじ高さ合わせ治具", "Size": "", "ToolOther": "FM-4086", "WorkName": "可動側ｸﾗﾝﾊﾟ―組立2", "WorkItems": [ "3. 2完成品の高さを調整する" ], "WorkPoints": [ "治具上面( 73.5㎜)を基準0とする", "左右のﾎﾞﾙﾄで調整", "右側規格値73.5㎜±0.02㎜", "左側規格値73.5㎜±0.02㎜", "中央規格値73.5㎜±0.03㎜" ], "Tolks": [ "締付ﾄﾙｸ 1.9N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:基板ｸﾗﾝﾊﾟｰ高さ調整" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-4086", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "7㎜", "ToolOther": "1.9N･m", "WorkName": "可動側ｸﾗﾝﾊﾟ―組立2", "WorkItems": [ "3. 2完成品の高さを調整する" ], "WorkPoints": [ "左側規格値73.5㎜±0.02㎜", "中央規格値73.5㎜±0.03㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:基板ｸﾗﾝﾊﾟｰ高さ調整" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "1.9N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "1/100", "ToolOther": "", "WorkName": "可動側ｸﾗﾝﾊﾟ―組立2", "WorkItems": [ "3. 2完成品の高さを調整する" ], "WorkPoints": [ "左側規格値73.5㎜±0.02㎜", "中央規格値73.5㎜±0.03㎜" ], "Tolks": [], "InspectionNo": "WETE-G002-C04", "InspectionItems": [ "検査表①:基板ｸﾗﾝﾊﾟｰ高さ調整" ], "WorkTypes": [], "Words": [ "WETE-G002-C04" ] }
{ "QualityItem": "高さ確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "左右:±0.02㎜以内中央部:±0.03㎜以内", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WETE-G002-C04", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(ｺﾝﾍﾞﾔｰ)", "Size": "", "ToolOther": "FM-6621", "WorkName": "ﾚｰﾝ1可動側銘板貼付", "WorkItems": [ "1. ①②にLABEL orLABEL を貼付ける" ], "WorkPoints": [ "80㎜", "6㎜", "6㎜", "80㎜", "16㎜", "10㎜", "流れ仕様によりどちらかを貼る", "LABEL はｽﾗｲﾄﾞ搬送OP時のみ使用" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "貼付確認", "ToolManageNo": "FM-6621", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り貼付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(ｺﾝﾍﾞﾔｰ)", "Size": "", "ToolOther": "FM-6621", "WorkName": "ﾚｰﾝ2可動側銘板貼付", "WorkItems": [ "1. ①②にLABEL orLABEL を貼付ける" ], "WorkPoints": [ "流れ仕様によりどちらかを貼る", "80㎜", "6㎜", "6㎜", "80㎜", "16㎜", "10㎜", "LABEL はｽﾗｲﾄﾞ搬送OP時のみ使用" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "貼付確認", "ToolManageNo": "FM-6621", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り貼付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(ｺﾝﾍﾞﾔｰ)", "Size": "", "ToolOther": "FM-6621", "WorkName": "ｱﾝﾌﾟｶﾊﾞｰ銘板貼付", "WorkItems": [ "1. COVER にLABEL かLABEL を貼付" ], "WorkPoints": [ "ﾚｰﾝ2左側", "ﾚｰﾝ2右側", "ﾚｰﾝ1左側", "ﾚｰﾝ1右側", "COVER の穴の位置に注意", "ﾚｰﾝ1左側､ﾚｰﾝ2右側はｽﾗｲﾄﾞ搬送OPが来た場合､LABEL を貼付けの事", "1㎜", "1㎜", "8㎜", "8㎜", "1㎜", "1㎜", "8㎜", "8㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "貼付確認", "ToolManageNo": "FM-6621", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り貼付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｺﾝﾍﾞｱｾﾝｻﾌﾞﾗｹｯﾄ組立ｼﾞｸﾞ(ﾋﾟｯﾁ8㎜)", "Size": "", "ToolOther": "FM-6502", "WorkName": "基板ｾﾝｻ前組1", "WorkItems": [ "2. 1完成品にFIBER をはめ､NUT-PLATE を矢印方向に寄せBOLT WASHER で取付", "1. ㉖にSPACER SPACER を入れる" ], "WorkPoints": [ "FIBER のピンを㉖にはめる", "ﾏｲﾅｽ溝を合わせる", "FIBER は黒線のｾﾝｻ側に取付", "この作業では同じものを4個製作" ], "Tolks": [ "締付ﾄﾙｸ 45cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-6502", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "45cN･m", "WorkName": "基板ｾﾝｻ前組1", "WorkItems": [ "2. 1完成品にFIBER をはめ､NUT-PLATE を矢印方向に寄せBOLT WASHER で取付" ], "WorkPoints": [ "FIBER のピンを㉖にはめる", "FIBER は黒線のｾﾝｻ側に取付", "この作業では同じものを4個製作" ], "Tolks": [ "締付ﾄﾙｸ 45cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "45cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｺﾝﾍﾞｱｾﾝｻﾌﾞﾗｹｯﾄ組立ｼﾞｸﾞ(ﾋﾟｯﾁ9㎜)", "Size": "", "ToolOther": "FM-6505", "WorkName": "基板ｾﾝｻ前組2", "WorkItems": [ "2. 1完成品にFIBER をはめ､NUT-PLATE を矢印方向に寄せBOLT WASHER で取付", "1. ㉖にSPACER SPACER を入れる" ], "WorkPoints": [ "FIBER は黒線のｾﾝｻ側に取付", "この作業では同じものを4個製作", "ﾏｲﾅｽ溝を合わせる", "FIBER のピンを㉖にはめる" ], "Tolks": [ "締付ﾄﾙｸ 45cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-6505", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "45cN･m", "WorkName": "基板ｾﾝｻ前組2", "WorkItems": [ "2. 1完成品にFIBER をはめ､NUT-PLATE を矢印方向に寄せBOLT WASHER で取付", "1. ㉖にSPACER SPACER を入れる" ], "WorkPoints": [ "FIBER は黒線のｾﾝｻ側に取付", "この作業では同じものを4個製作", "ﾏｲﾅｽ溝を合わせる" ], "Tolks": [ "締付ﾄﾙｸ 45cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "45cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍﾞｰｽ銘板貼付け", "WorkItems": [ "1. PLATE の表裏に砥石をかけﾊﾞﾘなどが無いか確認", "2. 1完成品の1個にLABEL を貼付" ], "WorkPoints": [ "1㎜", "62㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事", "Method": "目視", "RecordMethod": "-", "Other": "油砥石", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(ｺﾝﾍﾞﾔｰ)", "Size": "", "ToolOther": "FM-6621", "WorkName": "ﾍﾞｰｽ銘板貼付け", "WorkItems": [ "1. PLATE の表裏に砥石をかけﾊﾞﾘなどが無いか確認", "2. 1完成品の1個にLABEL を貼付" ], "WorkPoints": [ "1㎜", "62㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "貼付確認", "ToolManageNo": "FM-6621", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り貼付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾍﾞｰｽ部組立1", "WorkItems": [ "1. ①②にPIN PIN を圧入" ], "WorkPoints": [ "②Dﾋﾟﾝ 出代:4㎜", "PIN 割りﾋﾟﾝ出代:2㎜", "割りの向き", "割りの向き" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "出代確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "出代:指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍﾞｰｽ部組立2", "WorkItems": [ "1. ①②にLINEAR-WAY をBOLT で仮取付" ], "WorkPoints": [ "基準ﾋﾟﾝ", "手前側1個あける", "基準面", "基準ﾋﾟﾝ", "ｽﾗｲﾀﾞｰに刻印が無い方が基準面" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A052010-102にて本締め" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付けられている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "110cN･m", "WorkName": "ﾍﾞｰｽ部組立3", "WorkItems": [ "1. ①②にCLIP BOLT とCABLE-SUPPORT を取付ける" ], "WorkPoints": [ "K003-2(銘板が1枚)", "色枠内と同様にﾀｲﾏｳﾝﾄの向きを合わせる", "K003-1(銘板無し)" ], "Tolks": [ "締付ﾄﾙｸ 110cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "110cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "中央ﾍﾞｰｽ部組立", "WorkItems": [ "1. PLATE にLINEAR-WAY をBOLT で仮取付" ], "WorkPoints": [ "基準面" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A052010-102にて本締め" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付けられている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "固定側ﾎﾞｰﾙﾈｼﾞ部組立1", "WorkItems": [ "◆1. BRACKET BRACKET の穴とBEARING のﾎﾞｰﾙ部にｸﾞﾘｰｽを塗布", "2. 1完成品にBEARING を挿入SCREW で取付" ], "WorkPoints": [ "3箇所にｸﾞﾘｰｽを塗布する", "正面合わせ", "穴の側面に塗布する事", "向きに注意!(正面合わせにて取付)", "ｸﾞﾘｰｽを塗布した面同士を合わせる" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ容器", "ﾍﾞｱﾘﾝｸﾞ1つにつき5㎜づつ塗布する", "ｸﾞﾘｰｽ塗布 米粒:1", "ｸﾞﾘｰｽ塗布 米粒:1", "この作業では同じものを2個製作" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ｸﾞﾘｰｽ容器:各5㎜米粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "194cN･m", "WorkName": "固定側ﾎﾞｰﾙﾈｼﾞ部組立1", "WorkItems": [ "2. 1完成品にBEARING を挿入SCREW で取付" ], "WorkPoints": [ "3箇所にｸﾞﾘｰｽを塗布する", "正面合わせ", "向きに注意!(正面合わせにて取付)", "ｸﾞﾘｰｽを塗布した面同士を合わせる" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:1", "ｸﾞﾘｰｽ塗布 米粒:1", "◆作業者安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "各194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "固定側ﾎﾞｰﾙﾈｼﾞ部組立2", "WorkItems": [ "3. 1完成品に2完成品をWASHER WASHER NUT で仮取付", "◆1. ①②にｸﾞﾘｰｽを塗布", "2. PIN の最も中心に寄っている位置にﾏｰｷﾝｸﾞ" ], "WorkPoints": [ "PIN のﾏｰｷﾝｸﾞ位置は向かって左側にある事", "穴の側面に塗布する事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:各1", "仮止め:SD-A052010-117にて本締め" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ｺﾞﾏ粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "10㎜", "ToolOther": "6.0N･m", "WorkName": "固定側ﾎﾞｰﾙﾈｼﾞ部組立3", "WorkItems": [ "3. 2完成品にSPACER WASHER を取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "6.0N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "5.3N･m", "WorkName": "固定側ﾎﾞｰﾙﾈｼﾞ部組立4", "WorkItems": [ "2. 1完成品を④にBOLT WASHER で取付" ], "WorkPoints": [ "PLATE の溝にﾅｯﾄをはめる事", "WASHER のﾃｰﾊﾟｰ側がﾍﾞｱﾘﾝｸﾞ側になるように取付の事" ], "Tolks": [ "締付ﾄﾙｸ 5.3N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "6.0N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "10㎜", "ToolOther": "6.0N･m", "WorkName": "固定側ﾎﾞｰﾙﾈｼﾞ部組立5", "WorkItems": [ "1. BRACKET にSCREW WASHER NUT を取付", "2. BRACKET にSCREW WASHER NUT を取付", "1. BRACKET にSCREW WASHER NUT を取付", "2. BRACKET にSCREW WASHER NUT を取付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "各6.0N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "固定側ﾎﾞｰﾙﾈｼﾞ部組立5", "WorkItems": [ "1. BRACKET にSCREW WASHER NUT を取付", "2. BRACKET にSCREW WASHER NUT を取付", "1. BRACKET にSCREW WASHER NUT を取付", "2. BRACKET にSCREW WASHER NUT を取付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "出代:3.5㎜±1.0㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "油砥石", "Size": "細目", "ToolOther": "", "WorkName": "可動側ﾎﾞｰﾙﾈｼﾞ部組立1", "WorkItems": [ "2. 1完成品にLABEL を貼付け", "1. BRACKET BRACKET の底面に砥石をかける" ], "WorkPoints": [ "貼付前に㉖にて貼付部分を清掃する事", "㉗の段をピンク色矢印方向にBRACKET に当てつけ", "LABEL を㉗に青色矢印方向に合わせて貼付け" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "㉗可動側ボールネジ" ] }
{ "QualityItem": "表面確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ﾊﾞﾘ等無い事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(ｺﾝﾍﾞﾔｰ)", "Size": "", "ToolOther": "FM-6621", "WorkName": "可動側ﾎﾞｰﾙﾈｼﾞ部組立1", "WorkItems": [ "2. 1完成品にLABEL を貼付け", "1. BRACKET BRACKET の底面に砥石をかける" ], "WorkPoints": [ "貼付前に㉖にて貼付部分を清掃する事", "㉗の段をピンク色矢印方向にBRACKET に当てつけ", "LABEL を㉗に青色矢印方向に合わせて貼付け" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "㉗可動側ボールネジ" ] }
{ "QualityItem": "貼付確認", "ToolManageNo": "FM-6621", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り貼付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "可動側ﾎﾞｰﾙﾈｼﾞ部組立2", "WorkItems": [ "3. 1完成品に2完成品をWASHER WASHER NUT で仮取付", "◆1. ①②にｸﾞﾘｰｽを塗布", "2. PIN の最も中心に寄っている位置にﾏｰｷﾝｸﾞ" ], "WorkPoints": [ "PIN のﾏｰｷﾝｸﾞ位置は向かって左側にある事", "穴の側面に塗布する事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1", "仮止め:SD-A052010-118にて本締め" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ｺﾞﾏ粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "7㎜", "ToolOther": "1.4N･m", "WorkName": "可動側ﾎﾞｰﾙﾈｼﾞ部組立3", "WorkItems": [ "1. ①②にGREASE-NIPPLE を取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 1.4N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "1.4N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "可動側ﾎﾞｰﾙﾈｼﾞ部組立4", "WorkItems": [ "1. ①にDOG をBOLT WASHER で取付", "2. ③にCABLE-SUPPORT を取付" ], "WorkPoints": [ "13mm", "㉘を挟みDOG を水平に取付" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "Size": "13㎜", "ToolOther": "", "WorkName": "可動側ﾎﾞｰﾙﾈｼﾞ部組立4", "WorkItems": [ "1. ①にDOG をBOLT WASHER で取付", "2. ③にCABLE-SUPPORT を取付" ], "WorkPoints": [ "13mm", "㉘を挟みDOG を水平に取付" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "1回/3年", "ToolRecord": "校正成績書", "StdVal": "13㎜を挟み取付ける事", "Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾎﾞｰﾙﾈｼﾞ部組立左側", "WorkItems": [ "1. ①②③にBALL-SCREW を挿入し､BEARING を入れC-RING を取付" ], "WorkPoints": [ "ｼｬﾌﾄの向きに注意(ｼｬﾌﾄ部にﾈｼﾞ山有り)", "ｼｬﾌﾄの向きに注意(ﾘﾝｸﾞ溝有り)", "C-RING の角が丸い方がﾍﾞｱﾘﾝｸﾞ側に向く事", "②を図方向に挿入" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾌﾛﾝﾄ側", "BEARING ﾍﾞｱﾘﾝｸﾞ", "ｼｬﾌﾄ", "ﾘｱ側" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾎﾞｰﾙﾈｼﾞ部組立右側", "WorkItems": [ "1. ①②③にBALL-SCREW を挿入し､BEARING を入れC-RING を取付" ], "WorkPoints": [ "ｼｬﾌﾄの向きに注意(ｼｬﾌﾄ部にﾈｼﾞ山有り)", "ｼｬﾌﾄの向きに注意(ﾘﾝｸﾞ溝有り)", "C-RING の角が丸い方がﾍﾞｱﾘﾝｸﾞ側に向く事", "②を図方向に挿入" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾌﾛﾝﾄ側", "BEARING ﾍﾞｱﾘﾝｸﾞ", "ｼｬﾌﾄ", "ﾘｱ側" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(ｺﾝﾍﾞﾔｰ)", "Size": "", "ToolOther": "FM-6621", "WorkName": "固定ﾚｰﾙ銘板貼付け", "WorkItems": [ "1. FRAME の指示位置にLABEL orLABEL と⑦を貼付" ], "WorkPoints": [ "LABEL は延長時のみ使用", "延長ｺﾝﾍﾞﾔ仕様の場合代わりにLABEL を貼付け", "FRAME の形状が分かるように㉗を半透明にしています", "㉗（L2L1固定レール外側右端内側右端）をピンク色矢印方向に押し当て", "㉗（L2L1固定レール外側右端内側右端）をピンク色矢印方向に押し当て", "㉗（L1固定レール内側左端）をピンク色矢印方向に押し当て", "貼付前に㉖にて貼付部分を清掃する事", "LABEL 又はLABEL を㉗に青色矢印方向に合わせて貼付け" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "外側右端", "内側 左端", "内側 右端" ] }
{ "QualityItem": "貼付確認", "ToolManageNo": "FM-6621", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り貼付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "固定ﾚｰﾙｶﾞｲﾄﾞ取付1", "WorkItems": [ "1. ①にGUIDE GUIDE をBOLT WASHER で仮取付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A052010-124にて本締め" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視手感", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "固定ﾚｰﾙｶﾞｲﾄﾞ取付2", "WorkItems": [ "1. ①にGUIDE GUIDE をBOLT で仮取付" ], "WorkPoints": [ "①とGUIDE の切り欠きを合わせる事", "軽く締め付けておく事", "①とGUIDE の切り欠きを合わせる事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A052010-121にて本締め" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視手感", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "固定ﾚｰﾙｶﾞｲﾄﾞ取付3", "WorkItems": [ "1. ①にGUIDE をBOLT WASHER で仮取付" ], "WorkPoints": [ "軽く締め付けておく事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A052010-121にて本締め" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視手感", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "固定ﾚｰﾙｶﾞｲﾄﾞ取付4", "WorkItems": [ "1. ①にGUIDE をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.8㎜", "ToolOther": "", "WorkName": "固定ﾚｰﾙｶﾞｲﾄﾞ取付4", "WorkItems": [ "1. ①にGUIDE をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.8㎜を挟み取付ける事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.8㎜", "ToolOther": "", "WorkName": "固定ﾚｰﾙｶﾞｲﾄﾞ取付4", "WorkItems": [ "1. ①にGUIDE をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.7㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.8㎜", "ToolOther": "", "WorkName": "固定ﾚｰﾙｶﾞｲﾄﾞ取付4", "WorkItems": [ "1. ①にGUIDE をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.9㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "固定ﾚｰﾙｶﾞｲﾄﾞ取付5", "WorkItems": [ "1. ①にGUIDE をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.8㎜", "ToolOther": "", "WorkName": "固定ﾚｰﾙｶﾞｲﾄﾞ取付5", "WorkItems": [ "1. ①にGUIDE をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.8㎜を挟み取付ける事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.8㎜", "ToolOther": "", "WorkName": "固定ﾚｰﾙｶﾞｲﾄﾞ取付5", "WorkItems": [ "1. ①にGUIDE をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.7㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.8㎜", "ToolOther": "", "WorkName": "固定ﾚｰﾙｶﾞｲﾄﾞ取付5", "WorkItems": [ "1. ①にGUIDE をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.9㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "基板ｶﾞｲﾄﾞ位置決め治具(実装部)1.6㎜", "Size": "", "ToolOther": "FM-3558", "WorkName": "固定ﾚｰﾙｶﾞｲﾄﾞ位置調整", "WorkItems": [ "1. ①のｶﾞｲﾄﾞ位置を仮調整" ], "WorkPoints": [ "待機部:2.8㎜", "治具使用例", "治具使用例", "FM-3558", "FM-2845" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A052010-121にて本締め" ] }
{ "QualityItem": "段差確認", "ToolManageNo": "FM-3558", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "基板ｶﾞｲﾄﾞ位置出し治具(待機部)", "Size": "", "ToolOther": "FM-2845", "WorkName": "固定ﾚｰﾙｶﾞｲﾄﾞ位置調整", "WorkItems": [ "1. ①のｶﾞｲﾄﾞ位置を仮調整" ], "WorkPoints": [ "待機部:2.8㎜", "治具使用例", "治具使用例", "FM-3558", "FM-2845" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A052010-121にて本締め" ] }
{ "QualityItem": "段差確認", "ToolManageNo": "FM-2845", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "68cN･m", "WorkName": "固定ﾚｰﾙﾌﾟｰﾘｰ取付", "WorkItems": [ "1. ①にPULLEY PULLEY NUT WASHER を取付" ], "WorkPoints": [ "NUT を使用", "NUT を使用", "WASHER あり", "WASHER なし", "WASHER を入れる所と入れない所があるので注意", "FM-6571", "治具使用例" ], "Tolks": [ "締付ﾄﾙｸ 68cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "68cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｺﾝﾍﾞﾔｰ用ﾌﾟｰﾘ位置決めｼﾞｸﾞ(NPM-GW固定)", "Size": "", "ToolOther": "FM-6571", "WorkName": "固定ﾚｰﾙﾌﾟｰﾘｰ取付", "WorkItems": [ "1. ①にPULLEY PULLEY NUT WASHER を取付" ], "WorkPoints": [ "NUT を使用", "NUT を使用", "WASHER あり", "WASHER なし", "WASHER を入れる所と入れない所があるので注意", "FM-6571", "治具使用例" ], "Tolks": [ "締付ﾄﾙｸ 68cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-6571", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "固定ﾚｰﾙﾏｳﾝﾄ・ﾀﾞｸﾄ取付", "WorkItems": [ "1. ①にCABLE-SUPPORT を取付", "2. 1完成品にDUCT をBOLT WASHER で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(ｺﾝﾍﾞﾔｰ)", "Size": "", "ToolOther": "FM-6621", "WorkName": "可動ﾚｰﾙ銘板貼付け", "WorkItems": [ "1. FRAME の指示位置にLABEL ､LABEL orLABEL を貼付" ], "WorkPoints": [ "FRAME の形状が分かるように㉗を半透明にしています", "㉗(可動レール外側・内側右端）をピンク色矢印方向に押し当て", "LABEL は延長時のみ使用", "延長ｺﾝﾍﾞﾔ仕様の場合代わりにLABEL を貼付け", "㉗（可動レール外側・内側左端）をピンク色矢印方向に押し当て", "㉗(可動レール外側・内側右端）をピンク色矢印方向に押し当て", "㉗（可動レール外側・内側左端）をピンク色矢印方向に押し当て", "貼付前に㉖にて貼付部分を清掃する事", "LABEL 、LABEL 又はLABEL を㉗に青色矢印方向に合わせて貼付け" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "外側", "内側 左端", "内側 右端" ] }
{ "QualityItem": "貼付確認", "ToolManageNo": "FM-6621", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り貼付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "可動ﾚｰﾙｶﾞｲﾄﾞ取付1", "WorkItems": [ "1. ①にGUIDE GUIDE をBOLT WASHER で仮取付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A052010-124にて本締め" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視手感", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "可動ﾚｰﾙｶﾞｲﾄﾞ取付2", "WorkItems": [ "1. ①にGUIDE GUIDE をBOLT で仮取付" ], "WorkPoints": [ "軽く締め付けておく事", "①とGUIDE の切り欠きを合わせる事", "①とGUIDE の切り欠きを合わせる事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A052010-123にて本締め" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視手感", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "可動ﾚｰﾙｶﾞｲﾄﾞ取付3", "WorkItems": [ "1. ①にGUIDE をBOLT WASHER を仮取付" ], "WorkPoints": [ "軽く締め付けておく事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A052010-123にて本締め" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視手感", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "可動ﾚｰﾙｶﾞｲﾄﾞ取付4", "WorkItems": [ "1. ①にGUIDE をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.8㎜", "ToolOther": "", "WorkName": "可動ﾚｰﾙｶﾞｲﾄﾞ取付4", "WorkItems": [ "1. ①にGUIDE をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.8㎜を挟み取付ける事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.8㎜", "ToolOther": "", "WorkName": "可動ﾚｰﾙｶﾞｲﾄﾞ取付4", "WorkItems": [ "1. ①にGUIDE をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.7㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.8㎜", "ToolOther": "", "WorkName": "可動ﾚｰﾙｶﾞｲﾄﾞ取付4", "WorkItems": [ "1. ①にGUIDE をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.9㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "可動ﾚｰﾙｶﾞｲﾄﾞ取付5", "WorkItems": [ "1. ①にGUIDE をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.8㎜", "ToolOther": "", "WorkName": "可動ﾚｰﾙｶﾞｲﾄﾞ取付5", "WorkItems": [ "1. ①にGUIDE をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.8㎜を挟み取付ける事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.8㎜", "ToolOther": "", "WorkName": "可動ﾚｰﾙｶﾞｲﾄﾞ取付5", "WorkItems": [ "1. ①にGUIDE をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.7㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.8㎜", "ToolOther": "", "WorkName": "可動ﾚｰﾙｶﾞｲﾄﾞ取付5", "WorkItems": [ "1. ①にGUIDE をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.9㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "基板ｶﾞｲﾄﾞ位置決め治具(実装部)1.6㎜", "Size": "", "ToolOther": "FM-3558", "WorkName": "可動ﾚｰﾙｶﾞｲﾄﾞ位置調整", "WorkItems": [ "1. ①のｶﾞｲﾄﾞ位置を仮調整" ], "WorkPoints": [ "待機部:2.8㎜", "治具使用例", "治具使用例" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A052010-123にて本締め" ] }
{ "QualityItem": "段差確認", "ToolManageNo": "FM-3558", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "基板ｶﾞｲﾄﾞ位置出し治具(待機部)", "Size": "", "ToolOther": "FM-2845", "WorkName": "可動ﾚｰﾙｶﾞｲﾄﾞ位置調整", "WorkItems": [ "1. ①のｶﾞｲﾄﾞ位置を仮調整" ], "WorkPoints": [ "待機部:2.8㎜", "治具使用例", "治具使用例" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A052010-123にて本締め" ] }
{ "QualityItem": "段差確認", "ToolManageNo": "FM-2845", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "68cN･m", "WorkName": "可動ﾚｰﾙﾌﾟｰﾘ取付", "WorkItems": [ "1. ①にPULLEY PULLEY NUT WASHER を取付" ], "WorkPoints": [ "WASHER あり", "WASHER なし", "NUT を使用", "WASHER を入れる所と入れない所があるので注意", "NUT を使用", "FM-6589", "治具使用例" ], "Tolks": [ "締付ﾄﾙｸ 68cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "68cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｺﾝﾍﾞﾔｰ用ﾌﾟｰﾘ位置決めｼﾞｸﾞ(NPM-GW可動)", "Size": "", "ToolOther": "FM-6589", "WorkName": "可動ﾚｰﾙﾌﾟｰﾘ取付", "WorkItems": [ "1. ①にPULLEY PULLEY NUT WASHER を取付" ], "WorkPoints": [ "WASHER あり", "WASHER なし", "NUT を使用", "WASHER を入れる所と入れない所があるので注意", "NUT を使用", "FM-6589", "治具使用例" ], "Tolks": [ "締付ﾄﾙｸ 68cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-6589", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "110cN･m", "WorkName": "可動ﾚｰﾙﾏｳﾝﾄ・ﾀﾞｸﾄ取付", "WorkItems": [ "1. ①にCLIP をBOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 110cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "110cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "可動ﾚｰﾙﾏｳﾝﾄ・ﾀﾞｸﾄ取付", "WorkItems": [ "2. 1完成品にDUCT をBOLT WASHER で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "7㎜BOX", "ToolOther": "110cN･m", "WorkName": "可動ﾚｰﾙｹｰﾌﾞﾙﾍﾞｱﾌﾞﾗｹｯﾄ組立", "WorkItems": [ "1. BRACKET BRACKET にBRACKET をBOLT WASHER NUT で取付" ], "WorkPoints": [ "BRACKET とBRACKET の向きに注意する事", "BRACKET とBRACKET の向きに注意する事", "ﾅｯﾄをﾄﾙｸﾄﾞﾗｲﾊﾞｰで締め付ける事" ], "Tolks": [ "締付ﾄﾙｸ 110cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "110cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "80cN･m", "WorkName": "可動ﾚｰﾙｺﾈｸﾀﾌﾞﾗｹｯﾄ取付", "WorkItems": [ "4. 3完成品に2完成品をｲﾝｼｭﾛｯｸで取付", "3. 1完成品にCABLE-SUPPORT を取付", "1. ①②にBRACKET BRACKET をWASHER BOLT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 80cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "可動ﾚｰﾙﾌﾞﾗｹｯﾄ取付", "WorkItems": [ "1. ①に②③をBOLT WASHER で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "+No.0", "ToolOther": "18cN･m", "WorkName": "下受けﾋﾟﾝ検出ｾﾝｻ組立1", "WorkItems": [ "3. 2完成品を1完成品に⑥で取付", "1. BRACKET BRACKET にCOVER を取付", "2. SENSOR にSLIT を取付" ], "WorkPoints": [ "BRACKET BRACKET のCOVER 取付面を脱脂する事", "SENSOR とSLIT の取付穴を確実に合わせる事", "黒線:受光側" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "18cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "下受けﾋﾟﾝ検出ｾﾝｻ組立2", "WorkItems": [ "2. 1完成品にLABEL を取付", "1. ①に㉖で固定" ], "WorkPoints": [ "ﾗﾍﾞﾙ端面と収縮ﾁｭｰﾌﾞ端面を合わせて結束する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定" ] }
{ "QualityItem": "結束確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "作業指示通り結束出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "搬送ﾌﾟｰﾘ組立", "WorkItems": [ "1. PULLEY にRING を嵌め込む" ], "WorkPoints": [ "この作業では同じものを8個製作", "ﾘﾝｸﾞがﾌﾟｰﾘｰの溝の全周にわたり嵌っている事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "作業指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "300cN･m", "WorkName": "搬送ﾓｰﾀｰ組立固定ﾚｰﾙ用", "WorkItems": [ "1. ①にMOTOR をSCREW で取付" ], "WorkPoints": [ "Dｶｯﾄ面で締め付ける事" ], "Tolks": [ "締付ﾄﾙｸ 300cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1.2㎜", "0.9㎜", "この作業では同じものを2個製作", "この作業では同じものを2個製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "300cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.9㎜", "ToolOther": "", "WorkName": "搬送ﾓｰﾀｰ組立固定ﾚｰﾙ用", "WorkItems": [ "1. ①にMOTOR をSCREW で取付" ], "WorkPoints": [ "Dｶｯﾄ面で締め付ける事" ], "Tolks": [ "締付ﾄﾙｸ 300cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1.2㎜", "0.9㎜", "この作業では同じものを2個製作", "この作業では同じものを2個製作" ] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.9㎜を挟み取付ける事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "Size": "1.2㎜", "ToolOther": "", "WorkName": "搬送ﾓｰﾀｰ組立固定ﾚｰﾙ用", "WorkItems": [ "1. ①にMOTOR をSCREW で取付" ], "WorkPoints": [ "Dｶｯﾄ面で締め付ける事" ], "Tolks": [ "締付ﾄﾙｸ 300cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1.2㎜", "0.9㎜", "この作業では同じものを2個製作", "この作業では同じものを2個製作" ] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "1回/3年", "ToolRecord": "校正成績書", "StdVal": "1.2㎜を挟み取付ける事", "Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "300cN･m", "WorkName": "搬送ﾓｰﾀｰ組立可動ﾚｰﾙ用", "WorkItems": [ "1. ①にMOTOR を⑯で取付" ], "WorkPoints": [ "Dｶｯﾄ面で締め付ける事" ], "Tolks": [ "締付ﾄﾙｸ 300cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "3.0㎜", "この作業では同じものを2個製作", "2.7㎜", "この作業では同じものを2個製作" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "300cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "Size": "2.7㎜", "ToolOther": "", "WorkName": "搬送ﾓｰﾀｰ組立可動ﾚｰﾙ用", "WorkItems": [ "1. ①にMOTOR を⑯で取付" ], "WorkPoints": [ "Dｶｯﾄ面で締め付ける事" ], "Tolks": [ "締付ﾄﾙｸ 300cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "3.0㎜", "この作業では同じものを2個製作", "2.7㎜", "この作業では同じものを2個製作" ] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "1回/3年", "ToolRecord": "校正成績書", "StdVal": "2.7㎜を挟み取付ける事", "Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "Size": "2.7㎜", "ToolOther": "", "WorkName": "搬送ﾓｰﾀｰ組立可動ﾚｰﾙ用", "WorkItems": [ "1. ①にMOTOR を⑯で取付" ], "WorkPoints": [ "Dｶｯﾄ面で締め付ける事" ], "Tolks": [ "締付ﾄﾙｸ 300cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "3.0㎜", "この作業では同じものを2個製作", "2.7㎜", "この作業では同じものを2個製作" ] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "1回/3年", "ToolRecord": "校正成績書", "StdVal": "3.0㎜を挟み取付ける事", "Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "68cN･m", "WorkName": "搬送ﾓｰﾀｰ組立固定ﾌﾞﾗｹｯﾄ1", "WorkItems": [ "1. PLATE にPULLEY WASHER をWASHER NUT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 68cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "68cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "7㎜", "ToolOther": "194cN･m", "WorkName": "搬送ﾓｰﾀｰ組立固定ﾌﾞﾗｹｯﾄ1", "WorkItems": [ "2. 1完成品にWASHER SCREW を取付", "3. 2完成品にSPACER を取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "搬送ﾓｰﾀｰ組立固定ﾌﾞﾗｹｯﾄ3", "WorkItems": [ "1. ①②を③にBOLT WASHER WASHER で取付" ], "WorkPoints": [ "ｺﾈｸﾀ向き", "1.2㎜", "0.9㎜" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "68cN･m", "WorkName": "搬送ﾓｰﾀｰ組立固定ﾌﾞﾗｹｯﾄ4", "WorkItems": [ "3. 2完成品にCABLE-SUPPORT を取付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "68cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "7㎜", "ToolOther": "194cN･m", "WorkName": "搬送ﾓｰﾀｰ組立固定ﾌﾞﾗｹｯﾄ4", "WorkItems": [ "2. 1完成品にSPACER SCREW を取付", "1. PLATE にPULLEY WASHER WASHER をWASHER NUT で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 68cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "搬送ﾓｰﾀｰ組立固定ﾌﾞﾗｹｯﾄ6", "WorkItems": [ "1. ①②を③にBOLT WASHER WASHER で取付" ], "WorkPoints": [ "ｺﾈｸﾀ向き", "1.2㎜", "0.9㎜" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "搬送ﾓｰﾀｰ組立可動ﾌﾞﾗｹｯﾄ1", "WorkItems": [ "1. ①②をPLATE にBOLT WASHER WASHER で取付", "2. 1完成品にBRACKET をWASHER BOLT で取付" ], "WorkPoints": [ "3.0㎜", "2.7㎜", "矢印方向に当てつけ" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "各194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "搬送ﾓｰﾀｰ組立可動ﾌﾞﾗｹｯﾄ2", "WorkItems": [ "1. ①②をPLATE にBOLT WASHER WASHER で取付", "2. 1完成品にBRACKET をWASHER BOLT で取付" ], "WorkPoints": [ "3.0㎜", "2.7㎜" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "各194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "搬送ﾓｰﾀｰ組立可動ﾌﾞﾗｹｯﾄ3", "WorkItems": [ "1. ①にSHEET BRACKET をSPACER WASHER BOLT WASHER で仮取付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A052010-126にて本締め" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "搬送ﾓｰﾀｰ組立可動ﾌﾞﾗｹｯﾄ4", "WorkItems": [ "1. ①にSHEET BRACKET をSPACER WASHER BOLT WASHER で仮取付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "仮止め:SD-A052010-126にて本締め" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "自幅ﾓｰﾀｰ組立", "WorkItems": [ "1. MOTOR にBRACKET をBOLT WASHER WASHER で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｺﾈｸﾀ位置に注意" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "幅寄せ駆動ﾌﾟｰﾘ組立1", "WorkItems": [ "1. PLATE にPIN を圧入" ], "WorkPoints": [ "出代 4mm" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "出代確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "出代:4㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "160cN･m", "WorkName": "幅寄せ駆動ﾌﾟｰﾘ組立1", "WorkItems": [ "2. HOLDER にBEARING を入れSCREW で固定" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 160cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "160cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "6.0N･m", "WorkName": "幅寄せ駆動ﾌﾟｰﾘ組立2", "WorkItems": [ "1. ①に②をBOLT WASHER で取付" ], "WorkPoints": [ "①のピンに②を当付、㉘が入らないこと" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "6.0N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.03㎜", "ToolOther": "", "WorkName": "幅寄せ駆動ﾌﾟｰﾘ組立2", "WorkItems": [ "1. ①に②をBOLT WASHER で取付" ], "WorkPoints": [ "①のピンに②を当付、㉘が入らないこと" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.03㎜ｼｯｸﾈｽｹﾞｰｼﾞが入ら無い事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null