input stringclasses 1 value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "交換台車対応前面ｶﾊﾞｰ(ﾌﾛﾝﾄ)取付(OP:17連交換台車仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける",
"2. ⑥をBOLT WASHER で取付ける"
],
"WorkPoints": [
"LCRﾁｪｯｶｰ仕様時の場合⑥を取付ける",
"標準仕様(切り欠き無し)",
"LCRﾁｪｯｶｰ仕様(切り欠き有り)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"押し付け"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞ取付ﾛﾝｸﾞﾋﾞｯﾄM5",
"Size": "",
"ToolOther": "FM-6090",
"WorkName": "交換台車対応前面ｶﾊﾞｰ(ﾌﾛﾝﾄ)取付(OP:17連交換台車仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける",
"2. ⑥をBOLT WASHER で取付ける"
],
"WorkPoints": [
"LCRﾁｪｯｶｰ仕様時の場合⑥を取付ける",
"標準仕様(切り欠き無し)",
"LCRﾁｪｯｶｰ仕様(切り欠き有り)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"押し付け",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6090",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "T25",
"ToolOther": "6.0N･m",
"WorkName": "ITF17連/ASF34連交換台車対応前面ｶﾊﾞｰ(ﾌﾛﾝﾄ)取付(OP:17連台車切替仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける",
"2. ①の配線をｲﾝｼｭﾛｯｸで固定し､ｺﾈｸﾀ接続",
"3. ③を付属のﾎﾞﾙﾄで固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ITF17連/ASF34連交換台車対応前面ｶﾊﾞｰ(ﾌﾛﾝﾄ)取付(OP:17連台車切替仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける",
"2. ①の配線をｲﾝｼｭﾛｯｸで固定し､ｺﾈｸﾀ接続",
"3. ③を付属のﾎﾞﾙﾄで固定する"
],
"WorkPoints": [
"注意:切替仕様の台車ﾀｲﾌﾟの時のみ取付",
"③のｷｰを本体側安全SWに干渉無く接続する",
"ｺﾝﾍﾞﾔｰﾓｰﾀｰと配線が干渉し無い事",
"ｺﾈｸﾀ名称:S313/4R"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WETE-G002-D07",
"InspectionItems": [
"検査表①:ｾﾝｻ中継ﾌﾞﾗｹｯﾄ接続確認 Front"
],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WETE-G002-D07"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D07",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "2.0N･m",
"WorkName": "ITF17連/ASF34連交換台車対応前面ｶﾊﾞｰ(ﾌﾛﾝﾄ)取付(OP:17連台車切替仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける",
"2. ①の配線をｲﾝｼｭﾛｯｸで固定し､ｺﾈｸﾀ接続",
"3. ③を付属のﾎﾞﾙﾄで固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ITF17連/ASF34連交換台車対応前面ｶﾊﾞｰ(ﾌﾛﾝﾄ)取付(OP:17連台車切替仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける",
"2. ①の配線をｲﾝｼｭﾛｯｸで固定し､ｺﾈｸﾀ接続",
"3. ③を付属のﾎﾞﾙﾄで固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "T25",
"ToolOther": "6.0N･m",
"WorkName": "ITF17連/ASF34連交換台車対応前面ｶﾊﾞｰ(ﾌﾛﾝﾄ)調整(OP:17連台車切替仕様)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ITF17連/ASF34連交換台車対応前面ｶﾊﾞｰ(ﾌﾛﾝﾄ)調整(OP:17連台車切替仕様)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "3.5±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "T25",
"ToolOther": "6.0N･m",
"WorkName": "ITF17連/ASF34連交換台車対応前面ｶﾊﾞｰ(ﾌﾛﾝﾄ)調整(OP:17連台車切替仕様)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "130cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "T25",
"ToolOther": "6.0N･m",
"WorkName": "ITF17連/ASF34連交換台車対応前面ｶﾊﾞｰ(ﾌﾛﾝﾄ)調整(OP:17連台車切替仕様)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板下受けﾌﾞﾛｯｸ(一括交換_ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)ﾌﾛﾝﾄ搭載",
"WorkItems": [
"1. 基板下受けﾌﾞﾛｯｸ①を本体に搭載する"
],
"WorkPoints": [
"仕様を確認し､搭載する事",
"搭載のみ(ﾜﾝﾀｯﾁ型)",
"1ｹずつ(ﾌﾛﾝﾄ時)",
"一括交換_ﾌﾛﾝﾄ用3D図",
"搭載箇所(ﾌﾛﾝﾄ)",
"搭載箇所(ﾌﾛﾝﾄ)",
"下受けﾌﾞﾛｯｸ ﾚｲｱｳﾄ仕様図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"【一括交換式】",
"ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ時 (760x300)",
"GWRear専用",
"GWRear専用",
"GWFront専用",
"GWFront専用",
"■MTKA051682AA x2下受けﾌﾞﾛｯｸ一括交換(Front):NPM-GW",
"■MTKA051685AA x2下受けﾌﾞﾛｯｸ一括交換_ﾃﾞｭｱﾙ(Rear):NPM-GW",
"奥側装着",
"奥側装着",
"■MTKA051681AA x1下受けﾌﾞﾛｯｸ一括交換_ ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ_NPM-GW"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板下受けﾌﾞﾛｯｸ(一括交換_ﾃﾞｭｱﾙﾚｰﾝ専用仕様)ﾌﾛﾝﾄ搭載",
"WorkItems": [
"1. 基板下受けﾌﾞﾛｯｸ①を本体に搭載する"
],
"WorkPoints": [
"仕様を確認し､搭載する事",
"搭載のみ(ﾜﾝﾀｯﾁ型)",
"1ｹずつ(ﾌﾛﾝﾄ時)",
"一括交換_ﾌﾛﾝﾄ用3D図",
"搭載箇所(ﾌﾛﾝﾄ)",
"搭載箇所(ﾌﾛﾝﾄ)",
"下受けﾌﾞﾛｯｸ ﾚｲｱｳﾄ仕様図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"GWFront専用",
"GWFront専用",
"GWFront専用",
"GWFront専用",
"■MTKA052577AA x1下受けﾌﾞﾛｯｸ一括交換_ ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ専用_NPM-GW",
"■MTKA051682AA x2下受けﾌﾞﾛｯｸ一括交換(Front):NPM-GW",
"■MTKA051682AA x2下受けﾌﾞﾛｯｸ一括交換(Front):NPM-GW",
"ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ専用",
"(760x300)",
"【一括交換式】"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板下受けﾌﾞﾛｯｸ(一括交換_ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)ﾌﾛﾝﾄ搭載",
"WorkItems": [
"1. 基板下受けﾌﾞﾛｯｸ①を本体に搭載する"
],
"WorkPoints": [
"仕様を確認し､搭載する事",
"搭載のみ(ﾜﾝﾀｯﾁ型)",
"1ｹずつ(ﾌﾛﾝﾄ時)",
"一括交換_ﾌﾛﾝﾄ用3D図",
"搭載箇所(ﾌﾛﾝﾄ)",
"搭載箇所(ﾌﾛﾝﾄ)",
"下受けﾌﾞﾛｯｸ ﾚｲｱｳﾄ仕様図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"■ｼﾝｸﾞﾙｺﾝﾍﾞｱ",
"【一括交換式】",
"GWｼﾝｸﾞﾙRear専用",
"GWｼﾝｸﾞﾙRear専用",
"GWFront専用",
"GWFront専用",
"■MTKA051741AA x1下受けﾌﾞﾛｯｸ一括交換_ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ_NPM-GW",
"■MTKA051682AA x2下受けﾌﾞﾛｯｸ一括交換(Front):NPM-GW",
"■MTKA051742AA x2下受けﾌﾞﾛｯｸ一括交換_ｼﾝｸﾞﾙ(Rear):NPM-GW",
"(760x687)",
"687mm対応",
"687mm対応"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板下受けﾌﾞﾛｯｸ(一括交換_ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ(260㎜)仕様)ﾌﾛﾝﾄ搭載",
"WorkItems": [
"1. 基板下受けﾌﾞﾛｯｸ①を本体に搭載する"
],
"WorkPoints": [
"仕様を確認し､搭載する事",
"搭載のみ(ﾜﾝﾀｯﾁ型)",
"1ｹずつ(ﾌﾛﾝﾄ時)",
"一括交換_ﾌﾛﾝﾄ用3D図",
"搭載箇所(ﾌﾛﾝﾄ)",
"搭載箇所(ﾌﾛﾝﾄ)",
"下受けﾌﾞﾛｯｸ ﾚｲｱｳﾄ仕様図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"■ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ",
"【一括交換式】",
"ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ時 (760x260)",
"GWRear専用",
"GWRear専用",
"GWFront専用",
"GWFront専用",
"■MTKA051751AA x2下受けﾌﾞﾛｯｸ一括交換_260mm(Front):NPM-GW",
"■MTKA052879AA x2下受けﾌﾞﾛｯｸ一括交換_260mm(Rear):NPM-GW",
"奥側装着",
"奥側装着",
"■MTKA052877AA x1下受けﾌﾞﾛｯｸ一括交換_ ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ(260mm)_NPM-GW"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板下受けﾌﾞﾛｯｸ(一括交換_ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ専用(260㎜)仕様)ﾌﾛﾝﾄ搭載",
"WorkItems": [
"1. 基板下受けﾌﾞﾛｯｸ①を本体に搭載する"
],
"WorkPoints": [
"仕様を確認し､搭載する事",
"搭載のみ(ﾜﾝﾀｯﾁ型)",
"1ｹずつ(ﾌﾛﾝﾄ時)",
"一括交換_ﾌﾛﾝﾄ用3D図",
"搭載箇所(ﾌﾛﾝﾄ)",
"搭載箇所(ﾌﾛﾝﾄ)",
"下受けﾌﾞﾛｯｸ ﾚｲｱｳﾄ仕様図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"GWFront専用",
"GWFront専用",
"GWFront専用",
"GWFront専用",
"■MTKA052578AA x1下受けﾌﾞﾛｯｸ一括交換_ ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ専用(260mm)_NPM-GW",
"■MTKA051751AA x2下受けﾌﾞﾛｯｸ一括交換_260mm(Front):NPM-GW",
"■MTKA051751AA x2下受けﾌﾞﾛｯｸ一括交換_260mm(Front):NPM-GW",
"ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ専用",
"(760x260)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板下受けﾌﾞﾛｯｸ(自動交換_ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)ﾌﾛﾝﾄ搭載",
"WorkItems": [
"1. 基板下受けﾌﾞﾛｯｸ①を本体に搭載する"
],
"WorkPoints": [
"仕様を確認し､搭載する事",
"搭載のみ(ﾜﾝﾀｯﾁ型)",
"1ｹずつ(ﾌﾛﾝﾄ時)",
"自動交換_ﾌﾛﾝﾄ用3D図",
"搭載箇所(ﾌﾛﾝﾄ)",
"搭載箇所(ﾌﾛﾝﾄ)",
"下受けﾌﾞﾛｯｸ ﾚｲｱｳﾄ仕様図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"【自動交換式】",
"GWRear専用",
"GWRear専用",
"GWFront専用",
"GWFront専用",
"■MTKA051800AA x2下受けﾌﾞﾛｯｸ自動交換(Front):NPM-GW",
"■MTKA051809AA x2下受けﾌﾞﾛｯｸ自動交換_ﾃﾞｭｱﾙ(Rear):NPM-GW",
"奥側装着",
"■MTKA051852AA x1下受けﾌﾞﾛｯｸ自動交換_ ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ_NPM-GW",
"ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ時(760x300)",
"奥側装着"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板下受けﾌﾞﾛｯｸ(自動交換_ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)ﾌﾛﾝﾄ搭載",
"WorkItems": [
"1. 基板下受けﾌﾞﾛｯｸ①を本体に搭載する"
],
"WorkPoints": [
"仕様を確認し､搭載する事",
"搭載のみ(ﾜﾝﾀｯﾁ型)",
"1ｹずつ(ﾌﾛﾝﾄ時)",
"自動交換_ﾌﾛﾝﾄ用3D図",
"搭載箇所(ﾌﾛﾝﾄ)",
"搭載箇所(ﾌﾛﾝﾄ)",
"下受けﾌﾞﾛｯｸ ﾚｲｱｳﾄ仕様図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"■ｼﾝｸﾞﾙｺﾝﾍﾞｱ",
"【自動交換式】",
"GWｼﾝｸﾞﾙRear専用",
"GWｼﾝｸﾞﾙRear専用",
"GWFront専用",
"GWFront専用",
"■MTKA051800AA x2下受けﾌﾞﾛｯｸ自動交換(Front):NPM-GW",
"■MTKA051836AA x2下受けﾌﾞﾛｯｸ自動交換_ｼﾝｸﾞﾙ(Rear):NPM-GW",
"■MTKA051854AA x1下受けﾌﾞﾛｯｸ自動交換_ ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ_NPM-GW",
"(760x687)",
"687mm対応",
"687mm対応"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板下受けﾌﾞﾛｯｸ(自動交換_ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ(260㎜)仕様)ﾌﾛﾝﾄ搭載",
"WorkItems": [
"1. 基板下受けﾌﾞﾛｯｸ①を本体に搭載する"
],
"WorkPoints": [
"仕様を確認し､搭載する事",
"搭載のみ(ﾜﾝﾀｯﾁ型)",
"1ｹずつ(ﾌﾛﾝﾄ時)",
"自動交換_ﾌﾛﾝﾄ用3D図",
"搭載箇所(ﾌﾛﾝﾄ)",
"搭載箇所(ﾌﾛﾝﾄ)",
"下受けﾌﾞﾛｯｸ ﾚｲｱｳﾄ仕様図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"【自動交換式】",
"GWRear専用",
"GWRear専用",
"GWFront専用",
"GWFront専用",
"■MTKA051860AA x2下受けﾌﾞﾛｯｸ自動交換_260mm(Front):NPM-GW",
"■MTKA051862AA x2下受けﾌﾞﾛｯｸ自動交換_260mm(Rear):NPM-GW",
"奥側装着",
"奥側装着",
"■MTKA052581AA x1下受けﾌﾞﾛｯｸ自動交換_ ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ(260mm)_NPM-GW",
"ﾃﾞｭｱﾙﾚｰﾝﾓｰﾄﾞ時 (760x260)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ、廃棄BOX(ﾌﾛﾝﾄ)取付",
"WorkItems": [
"1. 廃棄BOX(①)及びﾉｽﾞﾙﾁｪﾝｼﾞｬｰ(②or③or④)を取付ける"
],
"WorkPoints": [
"仕様を確認し､搭載する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"or",
"or"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "10.0N･m",
"WorkName": "架台穴埋め(OP:17連交換台車/ﾄﾚｲﾌｨｰﾀﾞ連結部仕様)",
"WorkItems": [
"1. 架台へPLUG を取付ける"
],
"WorkPoints": [
"青丸のみ:ﾌﾟﾗｸﾞ埋込箇所",
"PLUG を架台に下記指示通り取付",
"PLUG 取付位置は供給部仕様で変わるので注意する",
"ﾄﾚｲﾌｨｰﾀﾞ連結部(本体側/F､R側)M10用×2個",
"右側は前工程で取付済み"
],
"Tolks": [
"締付ﾄﾙｸ 10.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "右側ﾌｨｰﾀﾞｰｶﾊﾞｰﾌﾞﾗｹｯﾄ取付(OP:17連交換台車、30連交換台車仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [
"①は下当てで取付ける",
"点線部取付ﾎﾞﾙﾄはﾌｨｰﾀﾞｰｶﾊﾞｰを移動させ固定する",
"①は仕様で形が変わるので注意する(下記は交換台車仕様)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "右側ﾌｨｰﾀﾞｰｶﾊﾞｰﾌﾞﾗｹｯﾄ取付(OP:ﾄﾚｲ、切替仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [
"①下当てで取付ける",
"点線部取付ﾎﾞﾙﾄはﾌｨｰﾀﾞｰｶﾊﾞｰを移動させ固定する",
"①は仕様で形が変わるので注意する(下記はﾄﾚｲ､切替仕様)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "左側ﾌｨｰﾀﾞｰｶﾊﾞｰﾌﾞﾗｹｯﾄ取付(OP:17連交換台車、30連交換台車仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [
"①下当てで取付ける",
"点線部取付ﾎﾞﾙﾄはﾌｨｰﾀﾞｰｶﾊﾞｰを移動させ固定する",
"①は仕様で形が変わるので注意する(下記は交換台車仕様)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "左側ﾌｨｰﾀﾞｰｶﾊﾞｰﾌﾞﾗｹｯﾄ取付(OP:ﾄﾚｲ、切替仕様)",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [
"①は仕様で形が変わるので注意する(下記はﾄﾚｲ､切替仕様)",
"①下当てで取付ける",
"点線部取付ﾎﾞﾙﾄはﾌｨｰﾀﾞｰｶﾊﾞｰを移動させ固定する"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(交換台車仕様)①",
"WorkItems": [
"1. ①をSCREW で仮付けする"
],
"WorkPoints": [
"SCREW 取付箇所詳細(交換台車仕様)",
"SCREW 取付箇所詳細(交換台車仕様)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"仮止め:SD-EJM2FH1-119にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(交換台車仕様)②",
"WorkItems": [
"■1. ①をSCREW SCREW WASHER で仮止めする"
],
"WorkPoints": [
"同一ﾛｯﾄNo.のこと",
"開閉ｶﾊﾞｰSWのﾛｯﾄNo.と合わせる事",
"①の下にWASHER をいれSCREW で仮止めする※交換台車仕様",
"SCREW は下から取付ける"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [
"検査表①:開閉ｶﾊﾞｰ&ﾌｨｰﾀﾞｰｶﾊﾞｰ安全SWのﾍﾟｱ確認"
],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"仮止め:SD-EJM2FH1-119にて本締め",
"設備下",
"WETE-G002-A01"
]
} | {
"QualityItem": "ﾛｯﾄNo.確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾛｯﾄNo.が同一である事",
"Method": "-",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(交換台車仕様)③",
"WorkItems": [
"1. HANDLE をSCREW で取付ける"
],
"WorkPoints": [
"HANDLE （ハンドル）とフィーダーカバーシートとの隙間を㉘を挟み固定する※ハンドルから手を離した状態で固定する",
"隙間:0.5㎜以上(最小隙間)"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"切り欠き",
"切り欠き",
"ｼｰﾄ",
"ｼｰﾄ",
"HANDLE の切り欠きに注意する",
"ｼｰﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.50㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(交換台車仕様)③",
"WorkItems": [
"1. HANDLE をSCREW で取付ける"
],
"WorkPoints": [
"HANDLE （ハンドル）とフィーダーカバーシートとの隙間を㉘を挟み固定する※ハンドルから手を離した状態で固定する",
"隙間:0.5㎜以上(最小隙間)"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"切り欠き",
"切り欠き",
"ｼｰﾄ",
"ｼｰﾄ",
"HANDLE の切り欠きに注意する",
"ｼｰﾄ"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜を挟みこみ固定する事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(交換台車仕様)④",
"WorkItems": [
"1. ﾌｨｰﾀﾞｰｶﾊﾞｰ取付確認､動作確認､増し締め実施"
],
"WorkPoints": [
"ﾎﾞﾙﾄ下から増し締め",
"ﾚﾊﾞｰ動作はﾊﾝﾄﾞﾙﾗﾍﾞﾙ部で実施",
"ﾚﾊﾞｰ動作時ﾌｨｰﾀﾞｰｶﾊﾞｰと干渉が無い事",
"ﾚﾊﾞｰも引っ掛かり無く動作する事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･ﾌｨｰﾀﾞｰｶﾊﾞｰを前後させ､動作に引っ掛かりが無い事･ｶﾊﾞｰや配線と干渉が無い事･増し締め本数:14ｶ所",
"ﾌｨｰﾀﾞｰｶﾊﾞｰを前後させ､動作に引っ掛かりが無い事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(交換台車仕様)④",
"WorkItems": [
"1. ﾌｨｰﾀﾞｰｶﾊﾞｰ取付確認､動作確認､増し締め実施"
],
"WorkPoints": [
"ﾎﾞﾙﾄ下から増し締め",
"ﾚﾊﾞｰ動作はﾊﾝﾄﾞﾙﾗﾍﾞﾙ部で実施",
"ﾚﾊﾞｰ動作時ﾌｨｰﾀﾞｰｶﾊﾞｰと干渉が無い事",
"ﾚﾊﾞｰも引っ掛かり無く動作する事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･ﾌｨｰﾀﾞｰｶﾊﾞｰを前後させ､動作に引っ掛かりが無い事･ｶﾊﾞｰや配線と干渉が無い事･増し締め本数:14ｶ所",
"ﾌｨｰﾀﾞｰｶﾊﾞｰを前後させ､動作に引っ掛かりが無い事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(交換台車仕様)⑤",
"WorkItems": [
"1. ①をSCREW で取付ける"
],
"WorkPoints": [
"SCREW は下から取付ける",
"①ｸﾞﾛﾒｯﾄは開閉ｶﾊﾞｰ先端に触れる程度で固定する",
"開閉ｶﾊﾞｰｸﾞﾛﾒｯﾄ",
"開閉ｶﾊﾞｰ先端",
"開閉ｶﾊﾞｰ先端",
"ﾚﾊﾞｰ解除時干渉し無い事",
"ﾚﾊﾞｰを動作させても安全SWと干渉しない様ｸﾞﾛﾒｯﾄ位置を調整する"
],
"Tolks": [
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"設備下",
"設備下",
"設備下"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "No.2",
"ToolOther": "1.6N･m",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(交換台車仕様)⑤",
"WorkItems": [
"1. ①をSCREW で取付ける"
],
"WorkPoints": [
"SCREW は下から取付ける",
"①ｸﾞﾛﾒｯﾄは開閉ｶﾊﾞｰ先端に触れる程度で固定する",
"開閉ｶﾊﾞｰｸﾞﾛﾒｯﾄ",
"開閉ｶﾊﾞｰ先端",
"開閉ｶﾊﾞｰ先端",
"ﾚﾊﾞｰ解除時干渉し無い事",
"ﾚﾊﾞｰを動作させても安全SWと干渉しない様ｸﾞﾛﾒｯﾄ位置を調整する"
],
"Tolks": [
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"設備下",
"設備下",
"設備下"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(ﾄﾚｲ仕様)①",
"WorkItems": [
"1. ①をSCREW で仮付けする"
],
"WorkPoints": [
"SCREW 取付箇所詳細(ﾄﾚｲ仕様,切替仕様)",
"SCREW 取付箇所詳細(ﾄﾚｲ仕様,切替仕様)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"仮止め:SD-EJM2FH1-124にて本締め",
"仕様で取付位置が変化(下記はﾄﾚｲ仕様､切替仕様)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(交換台車仕様)②",
"WorkItems": [
"■1. ①をSCREW SCREW WASHER で仮止めする"
],
"WorkPoints": [
"同一ﾛｯﾄNo.のこと",
"開閉ｶﾊﾞｰSWのﾛｯﾄNo.と合わせる事",
"①の上からSCREW SCREW で仮付けする※ﾄﾚｲ仕様時､切替仕様",
"SCREW は下から取付ける"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [
"検査表①:開閉ｶﾊﾞｰ&ﾌｨｰﾀﾞｰｶﾊﾞｰ安全SWのﾍﾟｱ確認"
],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"仮止め:SD-EJM2FH1-124にて本締め",
"設備下",
"仕様で取付位置が変化(下記はﾄﾚｲ仕様､切替仕様)",
"WETE-G002-A01"
]
} | {
"QualityItem": "ﾛｯﾄNo.確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾛｯﾄNo.が同一である事",
"Method": "目視",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(ﾄﾚｲ仕様)③",
"WorkItems": [
"1. HANDLE をSCREW で取付ける"
],
"WorkPoints": [
"HANDLE （ハンドル）とフィーダーカバーシートとの隙間を㉘を挟み固定する※ハンドルから手を離した状態で固定する",
"隙間:0.5㎜",
"隙間:0.5㎜以上(最小隙間)"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"切り欠き",
"切り欠き",
"ｼｰﾄ",
"ｼｰﾄ",
"HANDLE の切り欠きに注意する",
"ｼｰﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.50㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(ﾄﾚｲ仕様)③",
"WorkItems": [
"1. HANDLE をSCREW で取付ける"
],
"WorkPoints": [
"HANDLE （ハンドル）とフィーダーカバーシートとの隙間を㉘を挟み固定する※ハンドルから手を離した状態で固定する",
"隙間:0.5㎜",
"隙間:0.5㎜以上(最小隙間)"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"切り欠き",
"切り欠き",
"ｼｰﾄ",
"ｼｰﾄ",
"HANDLE の切り欠きに注意する",
"ｼｰﾄ"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜を挟みこみ固定する事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(ﾄﾚｲ仕様)④",
"WorkItems": [
"1. ﾌｨｰﾀﾞｰｶﾊﾞｰ取付確認､動作確認､増し締め実施"
],
"WorkPoints": [
"ﾎﾞﾙﾄ下から増し締め",
"ﾌｨｰﾀﾞｰｶﾊﾞｰは矢印方向に押し当てで固定する"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･ﾌｨｰﾀﾞｰｶﾊﾞｰを前後させ､動作に引っ掛かりが無い事･ｶﾊﾞｰや配線と干渉が無い事･増し締め本数:14ｶ所"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "No.2",
"ToolOther": "1.6N･m",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(ﾄﾚｲ仕様)④",
"WorkItems": [
"1. ﾌｨｰﾀﾞｰｶﾊﾞｰ取付確認､動作確認､増し締め実施"
],
"WorkPoints": [
"ﾎﾞﾙﾄ下から増し締め",
"ﾌｨｰﾀﾞｰｶﾊﾞｰは矢印方向に押し当てで固定する"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･ﾌｨｰﾀﾞｰｶﾊﾞｰを前後させ､動作に引っ掛かりが無い事･ｶﾊﾞｰや配線と干渉が無い事･増し締め本数:14ｶ所"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(ﾄﾚｲ仕様)⑤",
"WorkItems": [
"1. ①をSCREW で取付ける"
],
"WorkPoints": [
"SCREW は下から取付ける",
"①のｸﾞﾛﾒｯﾄは開閉ｶﾊﾞｰ先端に触れる程度で固定する",
"開閉ｶﾊﾞｰｸﾞﾛﾒｯﾄ",
"開閉ｶﾊﾞｰ先端",
"開閉ｶﾊﾞｰ先端",
"SCREW は下から取付ける",
"ﾚﾊﾞｰ解除時干渉し無い事",
"ﾚﾊﾞｰを動作させても安全SWと干渉しない様ｸﾞﾛﾒｯﾄ位置を調整する"
],
"Tolks": [
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"設備下",
"設備下",
"設備下"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "No.2",
"ToolOther": "1.6N･m",
"WorkName": "ﾌｨｰﾀﾞｰｶﾊﾞｰ取付(ﾄﾚｲ仕様)⑤",
"WorkItems": [
"1. ①をSCREW で取付ける"
],
"WorkPoints": [
"SCREW は下から取付ける",
"①のｸﾞﾛﾒｯﾄは開閉ｶﾊﾞｰ先端に触れる程度で固定する",
"開閉ｶﾊﾞｰｸﾞﾛﾒｯﾄ",
"開閉ｶﾊﾞｰ先端",
"開閉ｶﾊﾞｰ先端",
"SCREW は下から取付ける",
"ﾚﾊﾞｰ解除時干渉し無い事",
"ﾚﾊﾞｰを動作させても安全SWと干渉しない様ｸﾞﾛﾒｯﾄ位置を調整する"
],
"Tolks": [
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"設備下",
"設備下",
"設備下"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ取付",
"WorkItems": [
"1. ﾍｯﾄﾞ(①or②or③)を取付ける"
],
"WorkPoints": [
"M5×4本 締付け確認",
"仕様を確認し､搭載する事",
"前後同ﾀｲﾌﾟﾍｯﾄﾞ搭載時はSer No.の若い方をF側に取付ける事",
"㉖にてヘッド取付面にキズ等無い事を確認する事",
"3N取付時ｶﾒﾗ配線の噛みこみに注意する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"or",
"or",
"ﾘﾆｱｽｹｰﾙ及び配線に注意し､ﾍｯﾄﾞ取付け工具を挿入する事"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "傷等無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾍｯﾄﾞ取付",
"WorkItems": [
"1. ﾍｯﾄﾞ(①or②or③)を取付ける"
],
"WorkPoints": [
"M5×4本 締付け確認",
"仕様を確認し､搭載する事",
"前後同ﾀｲﾌﾟﾍｯﾄﾞ搭載時はSer No.の若い方をF側に取付ける事",
"㉖にてヘッド取付面にキズ等無い事を確認する事",
"3N取付時ｶﾒﾗ配線の噛みこみに注意する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"or",
"or",
"ﾘﾆｱｽｹｰﾙ及び配線に注意し､ﾍｯﾄﾞ取付け工具を挿入する事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞ取付けﾛﾝｸﾞﾋﾞｯﾄM5",
"Size": "",
"ToolOther": "FM-6090",
"WorkName": "ﾍｯﾄﾞ取付",
"WorkItems": [
"1. ﾍｯﾄﾞ(①or②or③)を取付ける"
],
"WorkPoints": [
"M5×4本 締付け確認",
"仕様を確認し､搭載する事",
"前後同ﾀｲﾌﾟﾍｯﾄﾞ搭載時はSer No.の若い方をF側に取付ける事",
"㉖にてヘッド取付面にキズ等無い事を確認する事",
"3N取付時ｶﾒﾗ配線の噛みこみに注意する"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"or",
"or",
"ﾘﾆｱｽｹｰﾙ及び配線に注意し､ﾍｯﾄﾞ取付け工具を挿入する事"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6090",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立①",
"WorkItems": [
"1. BRACKET に⑥をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾊﾞｰﾘﾝｸﾞ",
"ﾊﾞｰﾘﾝｸﾞ面に取付ける事",
"ｾﾝｻｰ配線の向きに注意する事",
"配線方向",
"配線方向"
],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B1047/1901TR",
"B1047/1901R"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立②",
"WorkItems": [
"1. ①へ②をSCREW で取付ける",
"2. 配線を引き回､ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"目視ﾚﾍﾞﾙで長穴ｾﾝﾀｰに取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B1047/1901TR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立②",
"WorkItems": [
"1. ①へ②をSCREW で取付ける",
"2. 配線を引き回､ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"目視ﾚﾍﾞﾙで長穴ｾﾝﾀｰに取付",
"ｺﾈｸﾀ接続確認"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表①:2.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"B1047/1901R",
"B1047/1901TR",
"B1047/1901TR",
"B1047/1901R",
"WETE-G002-A03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "81cN･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立③(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. ①へCOVER をBOLT で取付ける",
"2. 本体へBRACKET をBOLT WASHER で仮止めする",
"◆3. 1の完成品をSCREW BOLT WASHER で仮止めする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "81cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "81cN･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立③(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [],
"WorkPoints": [
"仮止め:SD-EJM8EH1-133にて本締め",
"仮止め:SD-EJM8EH1-133にて本締め"
],
"Tolks": [
"締付ﾄﾙｸ 81cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "81cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "延長ｺﾝﾍﾞｱｶﾊﾞｰ高さ調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6134",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立④",
"WorkItems": [
"1. 本体フレームのアイボルト取付穴に㉖を取付ける",
"2. ㉖治具にＧＷ専用のブロックを取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"右側面",
"ﾌﾛﾝﾄ",
"㉖ＧＷ専用ブロックは上当付けでノブで取付ける",
"㉖ＧＷ専用ブロック取付後に下からのノブで高さを固定する"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "FM-6134",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑤(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 仮止めﾈｼﾞを本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"開口部との干渉無い事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑤(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 仮止めﾈｼﾞを本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"開口部との干渉無い事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑤(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 仮止めﾈｼﾞを本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"開口部との干渉無い事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "延長ｺﾝﾍﾞｱｶﾊﾞｰ高さ調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6134",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑤(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 仮止めﾈｼﾞを本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"開口部との干渉無い事"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6134",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑤(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 仮止めﾈｼﾞを本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"開口部との干渉無い事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑤(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 仮止めﾈｼﾞを本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"開口部との干渉無い事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑤(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 仮止めﾈｼﾞを本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"開口部との干渉無い事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "延長ｺﾝﾍﾞｱｶﾊﾞｰ高さ調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6134",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑤(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 仮止めﾈｼﾞを本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間無い事",
"開口部との干渉無い事"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6134",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑥(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ300㎜仕様)",
"WorkItems": [
"1. 延長ｶﾊﾞｰにPLATE をNUT-PLATE SCREW で取付ける"
],
"WorkPoints": [
"仮止め:SD-EJM8EH1-139にて本締め",
"PLATE ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"PLATE は切り欠き側を固定する(300㎜対応)",
"NUT-PLATE を設備上側にし､SCREW を下側から取付ける(8箇所)",
"PLATE は切り欠き側を固定する(300㎜対応)",
"PLATE 設置時はﾚｰﾙを最小幅にしておく",
"PLATE 設置時はﾚｰﾙを最小幅にしておく",
"NUT-PLATE を設備上側にし､SCREW を下側から取付ける(8箇所)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑥(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｶﾊﾞｰにPLATE をNUT-PLATE SCREW で取付ける"
],
"WorkPoints": [
"仮止め:SD-EJM8EH1-140にて本締め",
"PLATE ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"PLATE は切り欠き側を固定する(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ対応)",
"PLATE 設置時はﾚｰﾙを最大幅にしておく",
"PLATE は切り欠き側を固定する(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ対応)",
"固定ﾚｰﾙ",
"可動ﾚｰﾙ",
"固定ﾚｰﾙ",
"可動ﾚｰﾙ",
"NUT-PLATE を設備上側にし､SCREW を下側から取付ける(8箇所)",
"NUT-PLATE を設備上側にし､SCREW を下側から取付ける(8箇所)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑥(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ260㎜仕様)",
"WorkItems": [
"1. 延長ｶﾊﾞｰにPLATE をNUT-PLATE SCREW で仮止め"
],
"WorkPoints": [
"仮止め:SD-EJM8EH1-139にて本締め",
"PLATE ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"PLATE は切り欠き無しを固定する(260㎜対応)",
"PLATE は切り欠き無しを固定する(260㎜対応)",
"PLATE 設置時はﾚｰﾙを最小幅にしておく",
"PLATE 設置時はﾚｰﾙを最小幅にしておく",
"NUT-PLATE を設備上側にし､SCREW を下側から取付ける(8箇所)",
"NUT-PLATE を設備上側にし､SCREW を下側から取付ける(8箇所)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "延長ｺﾝﾍﾞｱ板金平行調整ｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6367",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑦(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長コンベアーに㉖を仮止め、クランププレートを調整する"
],
"WorkPoints": [
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ固定ﾎﾞﾙﾄで調整する",
"仮止め:SD-EJM8EH1-139にて本締め"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"クランププレートを㉖に押し当て",
"クランププレートを㉖に押し当て",
"当付け箇所",
"当付け箇所"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6367",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "延長ｺﾝﾍﾞｱ板金平行調整ｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6367",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑦(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長コンベアーに㉖を仮止め、クランププレートを調整する"
],
"WorkPoints": [
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ固定ﾎﾞﾙﾄで調整する",
"仮止め:SD-EJM8EH1-140にて本締め"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"クランププレートを㉖に押し当て",
"当付け箇所",
"固定ﾚｰﾙ",
"可動ﾚｰﾙ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6367",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "延長ｺﾝﾍﾞｱ板金平行調整ｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6367",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑧(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最小ﾚｰﾙ幅50mmおよび最大幅(注1)にてそれぞれｳﾚﾀﾝとｸﾗﾝﾌﾟﾌﾟﾚｰﾄとの隙間が0.5±0.2㎜となるようにｸﾗﾝﾌﾟﾌﾟﾚｰﾄを取付ける",
"最大幅､最小幅で確認",
"最大幅､最小幅で確認",
"0.5±0.2㎜",
"0.5±0.2㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 0.8N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間(ｳﾚﾀﾝ側)",
"隙間",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"(目安:0.5㎜)",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"検査表①:ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ取付け調整",
"検査表①:ﾚｰﾝ2のｸﾗﾝﾌﾟﾕﾆｯﾄ取付け調整"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6367",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑧(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最小ﾚｰﾙ幅50mmおよび最大幅(注1)にてそれぞれｳﾚﾀﾝとｸﾗﾝﾌﾟﾌﾟﾚｰﾄとの隙間が0.5±0.2㎜となるようにｸﾗﾝﾌﾟﾌﾟﾚｰﾄを取付ける",
"最大幅､最小幅で確認",
"最大幅､最小幅で確認",
"0.5±0.2㎜",
"0.5±0.2㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 0.8N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間(ｳﾚﾀﾝ側)",
"隙間",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"(目安:0.5㎜)",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"検査表①:ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ取付け調整",
"検査表①:ﾚｰﾝ2のｸﾗﾝﾌﾟﾕﾆｯﾄ取付け調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.30㎜",
"ToolOther": "通り側",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑧(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最小ﾚｰﾙ幅50mmおよび最大幅(注1)にてそれぞれｳﾚﾀﾝとｸﾗﾝﾌﾟﾌﾟﾚｰﾄとの隙間が0.5±0.2㎜となるようにｸﾗﾝﾌﾟﾌﾟﾚｰﾄを取付ける",
"最大幅､最小幅で確認",
"最大幅､最小幅で確認",
"0.5±0.2㎜",
"0.5±0.2㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 0.8N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表①:ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ取付け調整"
],
"WorkTypes": [],
"Words": [
"隙間(ｳﾚﾀﾝ側)",
"隙間",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"(目安:0.5㎜)",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"検査表①:ﾚｰﾝ2のｸﾗﾝﾌﾟﾕﾆｯﾄ取付け調整",
"WETE-G002-A03"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5±0.2㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "0.8N･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑧(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最小ﾚｰﾙ幅50mmおよび最大幅(注1)にてそれぞれｳﾚﾀﾝとｸﾗﾝﾌﾟﾌﾟﾚｰﾄとの隙間が0.5±0.2㎜となるようにｸﾗﾝﾌﾟﾌﾟﾚｰﾄを取付ける",
"最大幅､最小幅で確認",
"最大幅､最小幅で確認",
"0.5±0.2㎜",
"0.5±0.2㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 0.8N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間(ｳﾚﾀﾝ側)",
"隙間",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"(目安:0.5㎜)",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"検査表①:ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ取付け調整",
"検査表①:ﾚｰﾝ2のｸﾗﾝﾌﾟﾕﾆｯﾄ取付け調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "0.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑧(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最小ﾚｰﾙ幅50mmおよび最大幅(注1)にてそれぞれｳﾚﾀﾝとｸﾗﾝﾌﾟﾌﾟﾚｰﾄとの隙間が0.5±0.2㎜となるようにｸﾗﾝﾌﾟﾌﾟﾚｰﾄを取付ける",
"最大幅､最小幅で確認",
"最大幅､最小幅で確認",
"0.5±0.2㎜",
"0.5±0.2㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 0.8N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間(ｳﾚﾀﾝ側)",
"隙間",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"(目安:0.5㎜)",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"検査表①:ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ取付け調整",
"検査表①:ﾚｰﾝ2のｸﾗﾝﾌﾟﾕﾆｯﾄ取付け調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "延長ｺﾝﾍﾞｱ板金平行調整ｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6367",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑧(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最小ﾚｰﾙ幅50mmおよび最大幅(注1)にてそれぞれｳﾚﾀﾝとｸﾗﾝﾌﾟﾌﾟﾚｰﾄとの隙間が0.5±0.2㎜となるようにｸﾗﾝﾌﾟﾌﾟﾚｰﾄを取付ける",
"0.5±0.2㎜",
"最大幅､最小幅で確認",
"0.5±0.2㎜",
"調整ﾎﾞﾙﾄ",
"調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 0.8N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"㉘を固定レールに押し当て",
"ﾚｰﾝ2",
"固定ﾚｰﾙ",
"可動ﾚｰﾙ",
"隙間(ｳﾚﾀﾝ側)",
"隙間",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"(目安:0.5㎜)",
"ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ",
"検査表①:ｸﾗﾝﾌﾟﾌﾟﾚｰﾄ取付け調整"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "FM-6367",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑧(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する",
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最大幅､最小幅で確認",
"最大幅､最小幅で確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"㉘を固定レールに押し当て",
"ﾚｰﾝ2",
"固定ﾚｰﾙ",
"可動ﾚｰﾙ",
"㉘を固定レールに押し当て",
"ﾚｰﾝ2",
"固定ﾚｰﾙ",
"可動ﾚｰﾙ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.30㎜",
"ToolOther": "通り側",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑧(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する",
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最大幅､最小幅で確認",
"最大幅､最小幅で確認"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"㉘を固定レールに押し当て",
"ﾚｰﾝ2",
"固定ﾚｰﾙ",
"可動ﾚｰﾙ",
"㉘を固定レールに押し当て",
"ﾚｰﾝ2",
"固定ﾚｰﾙ",
"可動ﾚｰﾙ",
"WETE-G002-A03"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5±0.2㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "0.8N･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑧(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最大幅､最小幅で確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"㉘を固定レールに押し当て",
"ﾚｰﾝ2",
"固定ﾚｰﾙ",
"可動ﾚｰﾙ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "0.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑧(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. 延長ｺﾝﾍﾞｱｰのｸﾗﾝﾌﾟﾌﾟﾚｰﾄとｳﾚﾀﾝｽﾄｯﾊﾟの隙間を調整する"
],
"WorkPoints": [
"最大幅､最小幅で確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"㉘を固定レールに押し当て",
"ﾚｰﾝ2",
"固定ﾚｰﾙ",
"可動ﾚｰﾙ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑨(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. BRACKET を固定ﾚｰﾙにNUT-PLATE BOLT BOLT WASHER で取付ける"
],
"WorkPoints": [
"振れ量:0.03㎜以内",
"振れ量:0.03㎜以内",
"㉖を固定レールに当て、レールが振れない様に締め付ける事",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"固定ﾚｰﾙ測定箇所",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ",
"固定ﾚｰﾙ",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ測定箇所"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "振れ量:0.03㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "2.0N･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑨(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. BRACKET を固定ﾚｰﾙにNUT-PLATE BOLT BOLT WASHER で取付ける"
],
"WorkPoints": [
"振れ量:0.03㎜以内",
"振れ量:0.03㎜以内",
"㉖を固定レールに当て、レールが振れない様に締め付ける事",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"固定ﾚｰﾙ測定箇所",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ",
"固定ﾚｰﾙ",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ測定箇所"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑨(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. BRACKET を固定ﾚｰﾙにNUT-PLATE BOLT BOLT WASHER で取付ける"
],
"WorkPoints": [
"振れ量:0.03㎜以内",
"振れ量:0.03㎜以内",
"㉖を固定レールに当て、レールが振れない様に締め付ける事",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"固定ﾚｰﾙ測定箇所",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ",
"固定ﾚｰﾙ",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ測定箇所"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑨(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. BRACKET を固定ﾚｰﾙにNUT-PLATE BOLT BOLT WASHER で取付ける"
],
"WorkPoints": [
"振れ量:0.03㎜以内",
"㉖を固定レールに当て、レールが振れない様に締め付ける事",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"固定ﾚｰﾙ測定箇所",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "振れ量:0.03㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "2.0N･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑨(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. BRACKET を固定ﾚｰﾙにNUT-PLATE BOLT BOLT WASHER で取付ける"
],
"WorkPoints": [
"振れ量:0.03㎜以内",
"㉖を固定レールに当て、レールが振れない様に締め付ける事",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"固定ﾚｰﾙ測定箇所",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑨(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. BRACKET を固定ﾚｰﾙにNUT-PLATE BOLT BOLT WASHER で取付ける"
],
"WorkPoints": [
"振れ量:0.03㎜以内",
"㉖を固定レールに当て、レールが振れない様に締め付ける事",
"開口部ｶﾊﾞｰよりBRACKET NUT-PLATE が上側へはみ出さないこと"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"固定ﾚｰﾙ測定箇所",
"NUT-PLATE ﾅｯﾄﾌﾟﾚｰﾄ",
"固定ﾚｰﾙ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "110cN･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑩(ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. ①を脱落防止ﾈｼﾞ(6箇所)で取付ける"
],
"WorkPoints": [
"脱落防止ﾈｼﾞ",
"PCｶﾊﾞｰにｷｽﾞ等無き事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "110cN･m",
"WorkName": "OP:右側延長ｺﾝﾍﾞｱ組立⑩(ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ仕様)",
"WorkItems": [
"1. ①を脱落防止ﾈｼﾞ(6箇所)で取付ける"
],
"WorkPoints": [
"脱落防止ﾈｼﾞ",
"PCｶﾊﾞｰにｷｽﾞ等無き事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸二人作業用ｾﾝｻｰｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6693",
"WorkName": "Y軸二人作業用ｾﾝｻｰｼﾞｸﾞ取り外し(ﾌﾛﾝﾄ)",
"WorkItems": [
"1. Y軸ｽﾄｯﾊﾟｰ治具(FM-6693)を取り外す"
],
"WorkPoints": [
"F側のＹ軸リニアスライダーから㉖を取り外す事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"マグネットに注意して㉖を取り外しする事",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "取り外し確認",
"ToolManageNo": "FM-6693",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取ﾘ外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾞﾛﾒｯﾄ(ﾘｱ)取付",
"WorkItems": [
"1. GROMMET GROMMET CABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"GROMMET GROMMET 3ｶ所に配線､配管を通す事",
"FT11を架台へ挿入する",
"S3737P/B1047T",
"FT11を架台へ挿入する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"◆荷重ﾁｪｯｶｰ仕様荷重ﾁｪｯｶｰの配線を通してからﾍｯﾄﾞOP駆動配線､配管を通す事",
"◆LCRﾁｪｯｶｰ仕様LCRﾁｪｯｶｰの配線を通してから基板ﾎﾙﾀﾞｰ配線､配管を通す事",
"ﾘｱ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "10.0N･m",
"WorkName": "架台穴埋め(OP:30連交換台車仕様)",
"WorkItems": [
"1. 架台へPLUG PLUG を取付ける"
],
"WorkPoints": [
"PLUG PLUG を架台に下記指示通り取付",
"PLUG PLUG 取付位置は供給部仕様で変わるので注意する",
"30連交換台車(左側)M10用×4個",
"30連交換台車(右側)M10用×4個",
"青丸のみ:ﾌﾟﾗｸﾞ埋込箇所"
],
"Tolks": [
"締付ﾄﾙｸ 10.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "10.0N･m",
"WorkName": "架台穴埋め(OP:17連交換台車仕様)",
"WorkItems": [
"1. 架台へPLUG PLUG を取付ける"
],
"WorkPoints": [
"PLUG PLUG を架台に下記指示通り取付",
"青丸のみ:ﾌﾟﾗｸﾞ埋込箇所",
"PLUG PLUG 取付位置は供給部仕様で変わるので注意する",
"17連交換台車駆動部(前後側/左側)M10用×4個",
"17連交換台車駆動部(前後側/右側)M10用×4個"
],
"Tolks": [
"締付ﾄﾙｸ 10.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "10.0N･m",
"WorkName": "架台穴埋め(OP:17連交換台車&ﾄﾚｲ仕様)",
"WorkItems": [
"1. 架台へPLUG を取付ける"
],
"WorkPoints": [
"PLUG を架台に下記指示通り取付",
"PLUG 取付位置は供給部仕様で変わるので注意する",
"17連交換台車駆動部(前後/右側/ﾄﾚｲ)M10用×5個",
"左側埋め栓は次工程で取付",
"青丸のみ:ﾌﾟﾗｸﾞ埋込箇所"
],
"Tolks": [
"締付ﾄﾙｸ 10.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "10.0N･m",
"WorkName": "架台穴埋め(OP:17連交換台車&交換台車切替仕様)",
"WorkItems": [
"1. 架台へPLUG PLUG を取付ける"
],
"WorkPoints": [
"PLUG PLUG を架台に下記指示通り取付",
"PLUG PLUG 取付位置は供給部仕様で変わるので注意する",
"17連交換台車切替仕様M10用×2個",
"17連交換台車駆動部(前後/右側/ﾄﾚｲ)M10用×5個",
"青丸のみ:ﾌﾟﾗｸﾞ埋込箇所"
],
"Tolks": [
"締付ﾄﾙｸ 10.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "10.0N･m",
"WorkName": "架台穴埋め(OP:17連交換台車&ﾄﾚｲﾌｨｰﾀﾞ連結部切替仕様)",
"WorkItems": [
"1. 架台へPLUG PLUG を取付ける"
],
"WorkPoints": [
"PLUG PLUG を架台に下記指示通り取付",
"PLUG PLUG 取付位置は供給部仕様で変わるので注意する",
"ﾄﾚｲﾌｨｰﾀﾞ連結部切替(前側)M10用×2個",
"17連交換台車駆動部(前後/右側/ﾄﾚｲ)M10用×5個",
"青丸のみ:ﾌﾟﾗｸﾞ埋込箇所"
],
"Tolks": [
"締付ﾄﾙｸ 10.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "OP:開口部ｾﾝｻ(ﾘｱ)取付(延長ｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"2. 1の完成品をBOLT WASHER で取付ける",
"1. ①②のｾﾝｻｰを取り外す"
],
"WorkPoints": [
"取り外したｾﾝｻｰは保管しておく事",
"下に押し付ける事",
"『左』延長ｺﾝﾍﾞｱ仕様時"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"押し付け",
"ｾﾝｻｰ",
"不要ﾎﾞﾙﾄ座金"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "開口部ｾﾝｻ(ﾘｱ)取付",
"WorkItems": [
"1. ①②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｺﾈｸﾀ名称:B1046/1901R",
"ｺﾈｸﾀ名称:B1047/1900TR",
"下に押し付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"押し付け",
"押し付け"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ(ﾘｱ)取付(OP:交換台車仕様)",
"WorkItems": [
"1. ①②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"･下に押し付ける事･①②は仕様で取付位置が変化するので注意する事",
"ｺﾈｸﾀ名称:B1237､B1240､B1241､B1242",
"ｺﾈｸﾀ名称:B1237T､B1240T､B1241T､B1242T",
"配線は架台内を通し引き回し",
"配線は架台内を通し引き回し"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"押し付け",
"押し付け",
"◆使用し無い事(ﾄﾚｲ仕様)",
"◆使用し無い事(ﾄﾚｲ仕様)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ(ﾘｱ)取付(OP:ﾄﾚｲ仕様、切替仕様)",
"WorkItems": [
"1. ①②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"配線は架台内を通し引き回し",
"･下に押し付ける事･①②は仕様で取付位置が変化するので注意する事",
"ｺﾈｸﾀ名称:B1237､B1240､B1241､B1242",
"ｺﾈｸﾀ名称:B1237T､B1240T､B1241T､B1242T",
"配線は架台内を通し引き回し"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"押し付け",
"押し付け",
"◆使用し無い事(交換台車仕様)",
"◆使用し無い事(交換台車仕様)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ｺﾈｸﾀﾌﾞﾗｹｯﾄ(R/R、R/L)取付",
"WorkItems": [
"1. ①②へ配線を接続し､本体ﾌﾚｰﾑへBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｺﾈｸﾀの名称に注意して接続する事",
"①取付前に接続",
"②取付前に接続"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"B1237",
"B1240",
"B1241",
"B1242",
"R/R",
"R/L",
"B1047T",
"B1237T",
"B1240T",
"B1241T",
"B1242T",
"B1046",
"S314P"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開口部配線処理(ﾘｱ)",
"WorkItems": [
"2. ﾌｧｲﾊﾞｰ線､開口部配線を引き回し､接続する",
"1.CABLE-SUPPORT を下記架台位置に取付ける"
],
"WorkPoints": [
"延長ｺﾝﾍﾞｱ仕様時:B1047T/B1046は未接続",
"配線接続確認",
"2ｶ所"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D07",
"InspectionItems": [
"検査表CABLE-SUPPORT :ｾﾝｻ中継ﾌﾞﾗｹｯﾄ接続確認 Rear"
],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"R/R",
"R/L",
"B1047T",
"B1046",
"延長ｺﾝﾍﾞｱ仕様未接続",
"延長ｺﾝﾍﾞｱ仕様未接続",
"ｺﾝﾍﾞｱと配線が干渉し無い事",
"ｺﾝﾍﾞｱと配線が干渉し無い事",
"WETE-G002-D07"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D07",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ(ﾘｱ)配線処理、ｺﾈｸﾀ接続",
"WorkItems": [
"1. ﾃｰﾌﾟ浮き､ﾌｧｲﾊﾞｰ線､開口部配線を引き回し､接続する"
],
"WorkPoints": [
"配線接続確認",
"延長ｺﾝﾍﾞｱ仕様時:B1047T/B1046は未接続"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D07",
"InspectionItems": [
"検査表①:ｾﾝｻ中継ﾌﾞﾗｹｯﾄ接続確認(Rear)"
],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"R/L",
"B1237T",
"B1240T",
"B1241T",
"B1242T",
"B1237",
"B1240",
"B1241",
"B1242",
"R/R",
"R/L",
"ﾃｰﾌﾟ浮きｾﾝｻｰ､開口部ｾﾝｻｰ配線を結束する",
"R/R",
"余長分は架台内で結束する",
"余長分は架台内で結束する",
"R/L",
"ﾃｰﾌﾟ浮きｾﾝｻｰ配線を結束する",
"WETE-G002-D07"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D07",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞ(ﾃﾞｭｱﾙ、ｼﾝｸﾞﾙ)配線・配管処理",
"WorkItems": [
"1. 配線､配管を接続する"
],
"WorkPoints": [
"配管接続確認",
"配線接続確認",
"後側",
"R4714R",
"R4715R",
"R4713R",
"B1726R",
"B1727R",
"B1740R",
"B1742R",
"FT11を架台に取付",
"203R",
"R4214R",
"R4215R",
"R4213R",
"B1226R",
"B1227R",
"B1115R",
"B1243R",
"FT11を架台に取付",
"204L",
"M629",
"B1110R"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D07",
"InspectionItems": [
"検査表①:基板ﾎﾙﾀﾞ部接続確認 Rear"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ﾘｱ",
"ﾌﾛﾝﾄ",
"検査表②:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認【配管の接続確認】",
"WETE-G002-D07"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D07",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞ(ﾃﾞｭｱﾙ、ｼﾝｸﾞﾙ)配線・配管処理",
"WorkItems": [
"1. 配線､配管を接続する"
],
"WorkPoints": [
"配管接続確認",
"配線接続確認",
"後側",
"R4714R",
"R4715R",
"R4713R",
"B1726R",
"B1727R",
"B1740R",
"B1742R",
"FT11を架台に取付",
"203R",
"R4214R",
"R4215R",
"R4213R",
"B1226R",
"B1227R",
"B1115R",
"B1243R",
"FT11を架台に取付",
"204L",
"M629",
"B1110R"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [
"検査表②:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認【配管の接続確認】"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ﾘｱ",
"ﾌﾛﾝﾄ",
"検査表①:基板ﾎﾙﾀﾞ部接続確認 Rear",
"WETE-G002-A01"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞ(ｼﾝｸﾞﾙ)配線・配管処理",
"WorkItems": [
"1. 配線､JOINT を接続する"
],
"WorkPoints": [
"配管接続確認",
"B1740R",
"B1742R",
"FT11を架台に取付",
"B1115R",
"B1243R",
"FT11を架台に取付",
"配管(203R､204L)は架台内でﾒｸﾗをする",
"204L",
"203R",
"ｼﾝｸﾞﾙ仕様時ﾘｱ側は､下受け配管を架台内にまとめる"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D07",
"InspectionItems": [
"検査表JOINT :基板ﾎﾙﾀﾞ部接続確認 Rear"
],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WETE-G002-D07"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D07",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "14㎜",
"ToolOther": "30N･m",
"WorkName": "熱補正ﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. ①を取付ける",
"2. 1完成品に②をBOLT で取付ける"
],
"WorkPoints": [
"2ｶ所"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "熱補正ﾌﾟﾚｰﾄ取付",
"WorkItems": [],
"WorkPoints": [
"プレート部を㉚に当付けて固定する隙間：0.03㎜以下",
"D-pin",
"ﾀｰｹﾞｯﾄの破損に注意する事",
"㉚を架台のピンにセットし熱補正を調整する"
],
"Tolks": [
"締付ﾄﾙｸ 30N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "熱補正ﾌﾟﾚｰﾄ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6373",
"WorkName": "熱補正ﾌﾟﾚｰﾄ取付",
"WorkItems": [],
"WorkPoints": [
"プレート部を㉚に当付けて固定する隙間：0.03㎜以下",
"D-pin",
"ﾀｰｹﾞｯﾄの破損に注意する事",
"㉚を架台のピンにセットし熱補正を調整する"
],
"Tolks": [
"締付ﾄﾙｸ 30N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6373",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.