Datasets:
ayuzawa
/
ManageProcess20

Dataset card Data Studio Files
xet
Community
1
input
stringclasses
1 value
instruction
stringlengths
222
3.65k
output
stringlengths
193
367
category
stringclasses
1 value
index
stringclasses
1 value
fileName
null
{ "ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応", "Size": "", "ToolOther": "FM-2222", "WorkName": "【OP】延長ｺﾝﾍﾞﾔｰｼﾝｸﾞﾙ幅寄せ確認", "WorkItems": [ "1. ｼﾝｸﾞﾙﾓｰﾄﾞの搬送ﾚｰﾙ幅の確認" ], "WorkPoints": [ "4ヶ所測定", "･ｼﾝｸﾞﾙﾓｰﾄﾞ最大幅687.5~687.8㎜ 最小幅50.5~50.8㎜", "F8 ENABLEを押しながら幅寄せ【687.5㎜】を押す" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:幅寄原点ｾﾝｻ位置調整及びﾚｰﾙ幅寄せ動作確認", "終了/戻る", "F8", "幅寄せ687.5mm", "幅寄せ50mm", "F8", "幅寄せ687.5mm", "幅寄せ50mm" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-2222", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り動作出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾉｷﾞｽ", "Size": "600㎜", "ToolOther": "", "WorkName": "【OP】延長ｺﾝﾍﾞﾔｰｼﾝｸﾞﾙ幅寄せ確認", "WorkItems": [ "1. ｼﾝｸﾞﾙﾓｰﾄﾞの搬送ﾚｰﾙ幅の確認" ], "WorkPoints": [ "4ヶ所測定", "･ｼﾝｸﾞﾙﾓｰﾄﾞ最大幅687.5~687.8㎜ 最小幅50.5~50.8㎜", "F8 ENABLEを押しながら幅寄せ【687.5㎜】を押す" ], "Tolks": [], "InspectionNo": "WETE-G002-C08", "InspectionItems": [ "検査表①:幅寄原点ｾﾝｻ位置調整及びﾚｰﾙ幅寄せ動作確認" ], "WorkTypes": [], "Words": [ "終了/戻る", "F8", "幅寄せ687.5mm", "幅寄せ50mm", "F8", "幅寄せ687.5mm", "幅寄せ50mm", "WETE-G002-C08" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "1回/年", "ToolRecord": "校正成績書", "StdVal": "687.5~687.8㎜50.5~50.8㎜", "Method": "ﾉｷﾞｽ", "RecordMethod": "WETE-G002-C08", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応", "Size": "", "ToolOther": "FM-2222", "WorkName": "自動動作確認①", "WorkItems": [ "1. 幅寄せ動作させ､ｱﾝﾌﾟの閾値を確認", "2. 基板検出ｾﾝｻの動作を確認", "1. 幅寄せ動作させ､ｱﾝﾌﾟの閾値を確認", "2. 基板検出ｾﾝｻの動作を確認" ], "WorkPoints": [ "F8 ENABLEを押しながら｢最小幅｣を押す※ﾚｰﾝ1､ﾚｰﾝ2同時に幅寄せが動作", "最大幅 687.5㎜", "閾値100以上", "ﾚｰﾝ1､ﾚｰﾝ2同様の作業の事", "F8 ENABLEを押しながら｢最小幅｣を押す※ﾚｰﾝ1､ﾚｰﾝ2同時に幅寄せが動作", "最大幅 687.5㎜", "閾値100以上", "ﾚｰﾝ1､ﾚｰﾝ2同様の作業の事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｾﾝｻｰ調整", "ﾚｰﾝ1", "ｾﾝｻｰｵｰﾄﾁｭｰﾆﾝｸﾞ", "ｾﾝｻｰ調整 標準", "ﾃﾞｭｱﾙ", "正流れ→", "最大幅 687.5mm", "最小幅", "ｾﾝｻｰｵｰﾄﾁｭｰﾆﾝｸﾞ", "最小幅", "F8", "検査表①:基板検出ｾﾝｻ動作確認", "検査表①:基板検出ｾﾝｻ光量/閾値確認", "ｾﾝｻｰ調整", "ﾚｰﾝ1", "ｾﾝｻｰｵｰﾄﾁｭｰﾆﾝｸﾞ", "ｾﾝｻｰ調整 標準", "ﾃﾞｭｱﾙ", "正流れ→", "最大幅 687.5mm", "最小幅", "ｾﾝｻｰｵｰﾄﾁｭｰﾆﾝｸﾞ", "最小幅", "F8", "検査表①:基板検出ｾﾝｻ動作確認", "検査表①:基板検出ｾﾝｻ光量/閾値確認" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-2222", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り動作出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "自動動作確認①", "WorkItems": [ "1. 幅寄せ動作させ､ｱﾝﾌﾟの閾値を確認", "2. 基板検出ｾﾝｻの動作を確認" ], "WorkPoints": [ "ｱﾝﾌﾟの閾値(緑色)を検査書に記入", "F8 ENABLEを押しながら｢最小幅｣を押す※ﾚｰﾝ1､ﾚｰﾝ2同時に幅寄せが動作", "最大幅 687.5㎜", "表示と遮光しているｾﾝｻが合っているか確認", "ﾚｰﾝを選択", "閾値100以上", "ONの事", "ﾚｰﾝ1､ﾚｰﾝ2同様の作業の事" ], "Tolks": [], "InspectionNo": "WETE-G002-C03", "InspectionItems": [ "検査表①:基板検出ｾﾝｻ動作確認" ], "WorkTypes": [], "Words": [ "ｾﾝｻｰ調整", "ﾚｰﾝ1", "ｾﾝｻｰｵｰﾄﾁｭｰﾆﾝｸﾞ", "ｾﾝｻｰ調整 標準", "ﾃﾞｭｱﾙ", "正流れ→", "最大幅 687.5mm", "最小幅", "ｾﾝｻｰｵｰﾄﾁｭｰﾆﾝｸﾞ", "最小幅", "F8", "ﾚｰﾝ1", "ﾚｰﾝ1", "終了/戻る", "検査表①:基板検出ｾﾝｻ光量/閾値確認", "WETE-G002-C03" ] }
{ "QualityItem": "ｾﾝｻ光量確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "閾値100以上", "Method": "目視", "RecordMethod": "WETE-G002-C03", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "搬送用ﾃｽﾄ基板(最小)", "Size": "", "ToolOther": "FM-2142", "WorkName": "自動動作確認①", "WorkItems": [ "1. 幅寄せ動作させ､ｱﾝﾌﾟの閾値を確認", "2. 基板検出ｾﾝｻの動作を確認" ], "WorkPoints": [ "F8 ENABLEを押しながら｢最小幅｣を押す※ﾚｰﾝ1､ﾚｰﾝ2同時に幅寄せが動作", "最大幅 687.5㎜", "閾値100以上", "ﾚｰﾝ1､ﾚｰﾝ2同様の作業の事" ], "Tolks": [], "InspectionNo": "WETE-G002-C03", "InspectionItems": [ "検査表①:基板検出ｾﾝｻ光量/閾値確認" ], "WorkTypes": [], "Words": [ "ｾﾝｻｰ調整", "ﾚｰﾝ1", "ｾﾝｻｰｵｰﾄﾁｭｰﾆﾝｸﾞ", "ｾﾝｻｰ調整 標準", "ﾃﾞｭｱﾙ", "正流れ→", "最大幅 687.5mm", "最小幅", "ｾﾝｻｰｵｰﾄﾁｭｰﾆﾝｸﾞ", "最小幅", "F8", "検査表①:基板検出ｾﾝｻ動作確認", "WETE-G002-C03" ] }
{ "QualityItem": "ｾﾝｻ動作確認", "ToolManageNo": "FM-2142", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ﾁｪｯｶｰの表示がONしている事", "Method": "目視", "RecordMethod": "WETE-G002-C03", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応", "Size": "", "ToolOther": "FM-2222", "WorkName": "自動動作確認②", "WorkItems": [ "1. 基板搬送確認を行う" ], "WorkPoints": [ "F8 ENABLEを押しながら搬送確認するﾚｰﾝと基板ｻｲｽﾞを押す", "ｼﾝｸﾞﾙﾓｰﾄﾞ用 最大幅 510×590×1.6基板 最小幅 50×50×0.3 基板", "※各基板を10枚搬送しｴﾗｰ無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｾﾝｻｰ調整", "基板搬送確認", "ﾚｰﾝ 1 687mm", "F8", "終了/戻る", "検査表①:基板搬送確認", "ﾓｰﾀ･ｱﾄﾞﾚｽ確認", "搬送ﾓｰﾀ確認", "幅寄せ確認", "自 動", "ｶｳﾝﾀｰﾘｾｯﾄ", "ｽﾄｯﾌﾟ", "ﾚｰﾝ 1", "ｶｳﾝﾀｰﾘｾｯﾄ", "ｽﾄｯﾌﾟ", "終了/戻る" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-2222", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り動作出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "搬送用ﾃｽﾄ基板(最小)", "Size": "", "ToolOther": "FM-2142", "WorkName": "自動動作確認②", "WorkItems": [ "1. 基板搬送確認を行う" ], "WorkPoints": [ "F8 ENABLEを押しながら搬送確認するﾚｰﾝと基板ｻｲｽﾞを押す", "ｼﾝｸﾞﾙﾓｰﾄﾞ用 最大幅 510×590×1.6基板 最小幅 50×50×0.3 基板", "※各基板を10枚搬送しｴﾗｰ無い事" ], "Tolks": [], "InspectionNo": "WETE-G002-C03", "InspectionItems": [ "検査表①:基板搬送確認" ], "WorkTypes": [], "Words": [ "ｾﾝｻｰ調整", "基板搬送確認", "ﾚｰﾝ 1 687mm", "F8", "終了/戻る", "ﾓｰﾀ･ｱﾄﾞﾚｽ確認", "搬送ﾓｰﾀ確認", "幅寄せ確認", "自 動", "ｶｳﾝﾀｰﾘｾｯﾄ", "ｽﾄｯﾌﾟ", "ﾚｰﾝ 1", "ｶｳﾝﾀｰﾘｾｯﾄ", "ｽﾄｯﾌﾟ", "終了/戻る", "WETE-G002-C03" ] }
{ "QualityItem": "搬送確認", "ToolManageNo": "FM-2142", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "基板を10枚搬送しｴﾗｰ無い事", "Method": "目視", "RecordMethod": "WETE-G002-C03", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "搬送用ﾃｽﾄ基板(最大)", "Size": "", "ToolOther": "FM-2712", "WorkName": "自動動作確認②", "WorkItems": [ "1. 基板搬送確認を行う" ], "WorkPoints": [ "F8 ENABLEを押しながら搬送確認するﾚｰﾝと基板ｻｲｽﾞを押す", "ｼﾝｸﾞﾙﾓｰﾄﾞ用 最大幅 510×590×1.6基板 最小幅 50×50×0.3 基板", "※各基板を10枚搬送しｴﾗｰ無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｾﾝｻｰ調整", "基板搬送確認", "ﾚｰﾝ 1 687mm", "F8", "終了/戻る", "検査表①:基板搬送確認", "ﾓｰﾀ･ｱﾄﾞﾚｽ確認", "搬送ﾓｰﾀ確認", "幅寄せ確認", "自 動", "ｶｳﾝﾀｰﾘｾｯﾄ", "ｽﾄｯﾌﾟ", "ﾚｰﾝ 1", "ｶｳﾝﾀｰﾘｾｯﾄ", "ｽﾄｯﾌﾟ", "終了/戻る", "WETE-G002-C03" ] }
{ "QualityItem": "搬送確認", "ToolManageNo": "FM-2712", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "基板を10枚搬送しｴﾗｰ無い事", "Method": "目視", "RecordMethod": "WETE-G002-C03", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "搬送用基板(510x320)", "Size": "", "ToolOther": "FM-3309", "WorkName": "自動動作確認②", "WorkItems": [ "1. 基板搬送確認を行う" ], "WorkPoints": [ "F8 ENABLEを押しながら搬送確認するﾚｰﾝと基板ｻｲｽﾞを押す", "ｼﾝｸﾞﾙﾓｰﾄﾞ用 最大幅 510×590×1.6基板 最小幅 50×50×0.3 基板", "※各基板を10枚搬送しｴﾗｰ無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｾﾝｻｰ調整", "基板搬送確認", "ﾚｰﾝ 1 687mm", "F8", "終了/戻る", "検査表①:基板搬送確認", "ﾓｰﾀ･ｱﾄﾞﾚｽ確認", "搬送ﾓｰﾀ確認", "幅寄せ確認", "自 動", "ｶｳﾝﾀｰﾘｾｯﾄ", "ｽﾄｯﾌﾟ", "ﾚｰﾝ 1", "ｶｳﾝﾀｰﾘｾｯﾄ", "ｽﾄｯﾌﾟ", "終了/戻る", "WETE-G002-C03" ] }
{ "QualityItem": "搬送確認", "ToolManageNo": "FM-3309", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "基板を10枚搬送しｴﾗｰ無い事", "Method": "目視", "RecordMethod": "WETE-G002-C03", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応", "Size": "", "ToolOther": "FM-2222", "WorkName": "自動動作確認③", "WorkItems": [ "1. 幅寄せ動作させ㉘を検出し止まるか確認" ], "WorkPoints": [ "最大幅付近 2箇所確認 (左､右)", "最小幅付近23箇所確認 (左､右)", "誤判定無い事", "動作操作はSD-A0520081-311､312を参照の事", "治具ﾋﾟﾝが可動ﾚｰﾙに干渉してい無い事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:ｺﾝﾍﾞﾔｰ幅寄せｲﾝﾀｰﾛｯｸ確認" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-2222", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り動作出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｲﾝﾀｰﾛｯｸｾﾝｻｰ動作確認ﾋﾟﾝ", "Size": "", "ToolOther": "FM-3325", "WorkName": "自動動作確認③", "WorkItems": [ "1. 幅寄せ動作させ㉘を検出し止まるか確認" ], "WorkPoints": [ "最大幅付近 2箇所確認 (左､右)", "最小幅付近23箇所確認 (左､右)", "誤判定無い事", "動作操作はSD-A0520081-311､312を参照の事", "治具ﾋﾟﾝが可動ﾚｰﾙに干渉してい無い事" ], "Tolks": [], "InspectionNo": "WETE-G002-C03", "InspectionItems": [ "検査表①:ｺﾝﾍﾞﾔｰ幅寄せｲﾝﾀｰﾛｯｸ確認" ], "WorkTypes": [], "Words": [ "WETE-G002-C03" ] }
{ "QualityItem": "検出確認", "ToolManageNo": "FM-3325", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "誤判定無い事", "Method": "目視", "RecordMethod": "WETE-G002-C03", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾎﾞｰﾙねじｸﾞﾘｰｽｱｯﾌﾟ", "WorkItems": [ "◆1. 幅寄せﾎﾞｰﾙﾈｼﾞのｸﾞﾘｰｽｱｯﾌﾟを行なう" ], "WorkPoints": [ "中央でｸﾞﾘｰｽｱｯﾌﾟ(計2個所)を行い全域に渡りｽﾄﾛｰｸする事" ], "Tolks": [], "InspectionNo": "WETE-G002-C03", "InspectionItems": [ "検査表①:幅寄せﾎﾞｰﾙﾈｼﾞｸﾞﾘｰｽｱｯﾌﾟ" ], "WorkTypes": [], "Words": [ "ｸﾞﾘｰｽ塗布 :各1ｼｮｯﾄ", "WETE-G002-C03" ] }
{ "QualityItem": "塗布確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所:各1ｼｮｯﾄ", "Method": "目視", "RecordMethod": "WETE-G002-C03", "Other": "ｸﾞﾘｰｽLCG100", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応", "Size": "", "ToolOther": "FM-2222", "WorkName": "ｴｰｼﾞﾝｸﾞ", "WorkItems": [ "1. ｴｰｼﾞﾝｸﾞを行う" ], "WorkPoints": [ "ｴｰｼﾞﾝｸﾞﾓｰﾄﾞにて140ｻｲｸﾙ(8H)問題なく動作する事" ], "Tolks": [], "InspectionNo": "WETE-G002-C03", "InspectionItems": [ "検査表①:ｴｰｼﾞﾝｸﾞ確認" ], "WorkTypes": [], "Words": [ "設定回数", "手 動", "自 動", "設 定", "終了/戻る", "ｴｰｼﾞﾝｸﾞ", "ｴｰｼﾞﾝｸﾞ回数", "ｶｳﾝﾀｰﾘｾｯﾄ", "ｽﾄｯﾌﾟ", "ｴｰｼﾞﾝｸﾞ開始", "終了/戻る", "ｴｰｼﾞﾝｸﾞ 標準", "ﾃﾞｭｱﾙ", "正流れ→", "WETE-G002-C03" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-2222", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "140ｻｲｸﾙ(8H)問題なく動作する事", "Method": "目視", "RecordMethod": "WETE-G002-C03", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "下受けﾋﾟﾝ検出ｾﾝｻ配線", "WorkItems": [ "1. ①の配線を引き回し､固定" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "各ﾓｰﾀｰ配線取付", "WorkItems": [ "1. ①にCABLE CABLE CABLE CABLE CABLE CABLE CABLE CABLE を引き回す" ], "WorkPoints": [ "M616R", "M614R", "M610R", "M612R", "M611R", "M613R", "M615R", "M617R", "固定側", "可動側" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ｺﾝﾍﾞｯｸｽ", "Size": "3m", "ToolOther": "", "WorkName": "ﾌｧｲﾊﾞｰｾﾝｻｰ前段取り", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±1.0㎜", "Method": "ｺﾝﾍﾞｯｸｽ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "45cN･m", "WorkName": "固定側ﾌｧｲﾊﾞｰｾﾝｻｰ取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "45cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し①", "WorkItems": [ "1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す", "2. 1完成品にBOLT WASHER を取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定" ] }
{ "QualityItem": "引き回し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き回し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し①", "WorkItems": [ "1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す", "2. 1完成品にBOLT WASHER を取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し②", "WorkItems": [ "1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す", "2. 1完成品にBOLT WASHER を取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定" ] }
{ "QualityItem": "引き回し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き回し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し②", "WorkItems": [ "1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す", "2. 1完成品にBOLT WASHER を取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "【選択仕様:逆流れ】固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し", "WorkItems": [ "1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "引き回し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き回し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "【OP:ｽﾗｲﾄﾞ搬送仕様】ﾚｰﾝ1固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し", "WorkItems": [ "1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定" ] }
{ "QualityItem": "引き回し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き回し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "【OP:延長ｺﾝﾍﾞﾔｰ仕様】固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し", "WorkItems": [ "3. ｵﾚﾝｼﾞ①､⑧のﾌｧｲﾊﾞｰ線を引き回す", "2. ｵﾚﾝｼﾞ①､⑧を延長側に作業1で外したM3x8とM3小型丸で取付", "1. SD-A052376-204のﾌｧｲﾊﾞｰｾﾝｻのｵﾚﾝｼﾞ①､⑧のﾌﾞﾗｹｯﾄ･ｽﾍﾟｰｻｰを取り外す" ], "WorkPoints": [ "仕様に従って､ｵﾚﾝｼﾞ① or ⑧ or 両方のﾌｧｲﾊﾞｰｾﾝｻのﾌﾞﾗｹｯﾄ･ｽﾍﾟｰｻｰを取り外す(ﾌﾞﾗｹｯﾄ､ｽﾍﾟｰｻｰ不要)", "ﾈｼﾞ､ﾜｯｼｬ流用" ], "Tolks": [ "締付ﾄﾙｸ 45cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "ﾌﾞﾗｹｯﾄ", "ｽﾍﾟｰｻ―" ] }
{ "QualityItem": "引き回し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き回し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "45cN･m", "WorkName": "【OP:延長ｺﾝﾍﾞﾔｰ仕様】固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し", "WorkItems": [], "WorkPoints": [ "ﾈｼﾞ､ﾜｯｼｬ流用" ], "Tolks": [ "締付ﾄﾙｸ 45cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾌﾞﾗｹｯﾄ", "ｽﾍﾟｰｻ―" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "45cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "固定側ﾀﾞｸﾄ取付", "WorkItems": [ "2. 1完成品にDUCT をBOLT WASHER で取付", "1. ①にDUCT をBOLT WASHER で取付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "固定側ﾀﾞｸﾄ取付", "WorkItems": [ "2. 1完成品にDUCT をBOLT WASHER で取付", "1. ①にDUCT をBOLT WASHER で取付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "可動側配管引き回し", "WorkItems": [ "1. ①にTUBE を引き回し､接続" ], "WorkPoints": [ "しっかり奥まで差込む事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "引き回し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き回し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "45cN･m", "WorkName": "可動側ﾌｧｲﾊﾞｰｾﾝｻ取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "45cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し①", "WorkItems": [ "1. ①にﾌｧｲﾊﾞｰｾﾝｻを引き回す", "2. 1完成品にBOLT WASHER を取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定" ] }
{ "QualityItem": "引き回し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き回し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し①", "WorkItems": [ "1. ①にﾌｧｲﾊﾞｰｾﾝｻを引き回す", "2. 1完成品にBOLT WASHER を取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し②", "WorkItems": [ "1. ①にﾌｧｲﾊﾞｰｾﾝｻを引き回す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定" ] }
{ "QualityItem": "引き回し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き回し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "", "ToolOther": "", "WorkName": "可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し②", "WorkItems": [ "1. ①にﾌｧｲﾊﾞｰｾﾝｻを引き回す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "【選択仕様:逆流れ】可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し", "WorkItems": [ "1. ①にﾌｧｲﾊﾞｰｾﾝｻを引き回す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定" ] }
{ "QualityItem": "引き回し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き回し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "【OP:ｽﾗｲﾄﾞ搬送仕様】可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し", "WorkItems": [ "1. ①にﾌｧｲﾊﾞｰｾﾝｻを引き回す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定" ] }
{ "QualityItem": "引き回し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き回し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "【OP:延長ｺﾝﾍﾞﾔｰ仕様】可動側ﾌｧｲﾊﾞｰｾﾝｻ引き回し", "WorkItems": [ "1. ①にﾌｧｲﾊﾞｰｾﾝｻを引き回す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定" ] }
{ "QualityItem": "引き回し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き回し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "可動側ﾀﾞｸﾄ取付", "WorkItems": [], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 150cN･m", "締付ﾄﾙｸ 150cN･m", "締付ﾄﾙｸ 150cN･m", "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "180cN･m", "WorkName": "可動側左側ﾍﾞｱ整線①", "WorkItems": [ "3. ﾍﾞｱ配線のCABLE のｺﾈｸﾀをﾌﾞﾗｹｯﾄに取付", "2. 1完成品をｲﾝｼｭﾛｯｸで固定", "■1. ①にSCREW を取付" ], "WorkPoints": [ "B1026P", "FGCVM1" ], "Tolks": [ "締付ﾄﾙｸ 180cN･m" ], "InspectionNo": "WETE-G002-C04", "InspectionItems": [], "WorkTypes": [], "Words": [ "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "180cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "可動側左側ﾍﾞｱ整線②", "WorkItems": [ "1. TUBE に①のﾌｧｲﾊﾞｰを通す", "2. CABLE-BEAR のふたを開け配線を入れる", "3. CABLE-BEAR のふたを閉じて､ﾚｰﾙ側の固定金具に取付", "4. 下側の固定金具に取付" ], "WorkPoints": [ "通してあるｲﾝｼｭﾛｯｸにて固定", "A矢視", "上側", "下側" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "配管", "配管", "B1026", "M613R", "M611R" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "180cN･m", "WorkName": "可動側右側ﾍﾞｱ整線①", "WorkItems": [ "■1. ①のFG線をSCREW で取付", "2. 1完成品に㉘で配線を固定", "3. ﾍﾞｱ配線のCABLE CABLE のｺﾈｸﾀをﾌﾞﾗｹｯﾄに取付", "4. ﾚｰﾙ側配線をｺﾈｸﾀに挿入" ], "WorkPoints": [ "B121P", "B1126P", "FGCVM2", "FGCVM3" ], "Tolks": [ "締付ﾄﾙｸ 180cN･m" ], "InspectionNo": "WETE-G002-C04", "InspectionItems": [], "WorkTypes": [], "Words": [ "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "180cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "可動側右側ﾍﾞｱ整線②", "WorkItems": [ "1. TUBE に①のﾌｧｲﾊﾞｰを通す", "2. CABLE-BEAR のふたを開け配線を入れる", "3. CABLE-BEAR のふたを閉じて､ﾚｰﾙ側の固定金具に取付", "4. 下側の固定金具に取付" ], "WorkPoints": [ "L1側", "A矢視", "上側", "下側", "通してあるｲﾝｼｭﾛｯｸにて固定" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "M615R", "M617R", "B121P", "B1126P" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "右側配線①", "WorkItems": [ "1. ①にCABLE を引き回す" ], "WorkPoints": [ "B123R" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定" ] }
{ "QualityItem": "引き回し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き回し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "右側配線②", "WorkItems": [ "1. ①にCABLE を引き回す" ], "WorkPoints": [ "太線のみ板金と固定する事単線は単線のみで固定", "配線が張らないようにする事", "L1側", "L1側" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "B1132", "B1133", "B1125", "B1124" ] }
{ "QualityItem": "引き回し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き回し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "左側配線", "WorkItems": [ "1. ①にCABLE を引き回す" ], "WorkPoints": [ "L1側", "太線のみ板金と固定する事単線は単線のみで固定", "配線が張らないようにする事", "L1側" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "B1020", "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "B1021", "B1022", "B1023", "【OP】B1030", "【OP】B1031" ] }
{ "QualityItem": "引き回し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き回し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "固定側ﾏｰｸﾁｭｰﾌﾞ挿入", "WorkItems": [ "1. ①ﾌｧｲﾊﾞｰ線にMARK TUBE MARK TUBE を挿入" ], "WorkPoints": [ "ｽﾗｲﾄﾞ搬送OP仕様" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "A矢視", "B矢視", "MARK TUBE ", "MARK TUBE ", "A矢視", "B矢視" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "可動側ﾏｰｸﾁｭｰﾌﾞ挿入", "WorkItems": [ "1. ①ﾌｧｲﾊﾞｰ線にMARK TUBE MARK TUBE を挿入" ], "WorkPoints": [ "ｽﾗｲﾄﾞ搬送OP仕様" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "A矢視", "B矢視", "MARK TUBE ", "MARK TUBE ", "A矢視", "B矢視" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "左側配線ﾌﾞﾗｹｯﾄ固定側ﾌｧｲﾊﾞｰ引き回し確認", "WorkItems": [ "1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す" ], "WorkPoints": [ "上記のように引き回す事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "引き回し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き回し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "左側配線ﾌﾞﾗｹｯﾄ可動側ﾌｧｲﾊﾞｰ整線", "WorkItems": [ "1. ①のﾌｧｲﾊﾞｰｾﾝｻを固定", "2. JOINT にTUBE を接続", "3. 2完成品にCABLE を引き回し" ], "WorkPoints": [ "通してあるｲﾝｼｭﾛｯｸに固定", "CABLE R4237Rは使用しないので丸部で固定", "CABLE 未使用なのでまとめる", "延長ｺﾝﾍﾞﾔｰ仕様ではTUBE CABLE R4236Rをﾊﾞﾙﾌﾞに接続", "JOINT は未使用" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "標準仕様", "延長ｺﾝﾍﾞﾔｰ仕様", "拡大図" ] }
{ "QualityItem": "整線確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り整線出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "左側ﾌｧｲﾊﾞｰ線接続", "WorkItems": [ "1. ①のﾌｧｲﾊﾞｰ線接続" ], "WorkPoints": [ "付属のﾌｧｲﾊﾞｰｶｯﾀｰでｶｯﾄして接続する", "上段:可動側(黄)", "下段:固定側(白)", "ﾌｧｲﾊﾞｰ線を奥まで挿入する事", "ﾌｧｲﾊﾞｰﾛｯｸﾚﾊﾞｰがﾛｯｸされている事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "B1023", "B1022", "B1021", "B1020", "【OP】B1031", "【OP】B1030" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "右側配線ﾌﾞﾗｹｯﾄ固定側ﾌｧｲﾊﾞｰ引き回し確認", "WorkItems": [ "1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す" ], "WorkPoints": [ "上記のように引き回す事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "引き回し確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り引き回し出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "右側配線ﾌﾞﾗｹｯﾄ可動側ﾌｧｲﾊﾞｰ整線", "WorkItems": [ "2. 1完成品のｺﾈｸﾀ挿入", "1. ①のﾌｧｲﾊﾞｰｾﾝｻを引き回す" ], "WorkPoints": [ "通してあるｲﾝｼｭﾛｯｸに固定" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定" ] }
{ "QualityItem": "整線確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り整線出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "右側ﾌｧｲﾊﾞｰｾﾝｻ接続", "WorkItems": [ "1. ①のﾌｧｲﾊﾞｰ線接続" ], "WorkPoints": [ "付属のﾌｧｲﾊﾞｰｶｯﾀｰでｶｯﾄして接続する", "上段:可動側(黄)", "下段:固定側(白)", "ﾌｧｲﾊﾞｰ線を奥まで挿入する事", "ﾌｧｲﾊﾞｰﾛｯｸﾚﾊﾞｰがﾛｯｸされている事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "B1124", "B1125", "B1132", "B1133" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "ｱﾝﾌﾟｶﾊﾞｰ取付", "WorkItems": [ "1. ①に②をBOLT WASHER で取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "6.0N･m", "WorkName": "幅寄せﾓｰﾀｰ取付", "WorkItems": [ "1. ①に②をBOLT WASHER で取付" ], "WorkPoints": [ "ﾋﾟﾝにしっかりはまっている事", "取付前に㉚をシャフトに挿入しておく事" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "6.0N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "幅寄せﾓｰﾀｰ取付", "WorkItems": [ "2. 治具にてﾓｰﾀｰとｼｬﾌﾄの芯出し" ], "WorkPoints": [ "治具を動かし､引っ掛かりが無い事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "100cN･m", "WorkName": "幅寄せﾓｰﾀｰ取付", "WorkItems": [ "3. 2完成品にCOUPLING を取付" ], "WorkPoints": [ "付属ﾎﾞﾙﾄ締結", "目視にて青丸部隙間が均等になっている事", "COUPLING は矢印方向に当てつけながら締結" ], "Tolks": [ "締付ﾄﾙｸ 100cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｶｯﾌﾟﾘﾝｸﾞ治具(Φ8×Φ8)", "Size": "", "ToolOther": "FM-1198", "WorkName": "幅寄せﾓｰﾀｰ取付", "WorkItems": [ "2. 治具にてﾓｰﾀｰとｼｬﾌﾄの芯出し", "1. ①に②をBOLT WASHER で取付" ], "WorkPoints": [ "治具を動かし､引っ掛かりが無い事", "ﾋﾟﾝにしっかりはまっている事", "取付前に㉚をシャフトに挿入しておく事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-1198", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞ駆動部組付け", "WorkItems": [ "◆1.⑥をｸﾚｰﾝ等でもち上げ､ 取付け全てを油砥石で均し､①に組付ける(BOLT で固定)", "2.組付け後､加工面には金ﾆｽを塗布すること｡" ], "WorkPoints": [ "ﾋﾟﾝに当てつけて組付けて固定する事", "ﾋﾟﾝに当てつけて組付けて固定する事", "隙間:0.01mm未満", "この作業ではP1用･P2用の2ｾｯﾄ作成の事｡(仕様によりP2無しの仕様も有り)" ], "Tolks": [], "InspectionNo": "WWYJ-5300-061", "InspectionItems": [ "検査表①:駆動部ﾌﾚｰﾑ規正ﾋﾟﾝ隙間確認" ], "WorkTypes": [], "Words": [ "◆作業者安全作業", "WWYJ-5300-061" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "WWYJ-5300-061", "Other": "-", "ProcessNames": [] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞ駆動部組付け", "WorkItems": [ "◆1.⑥をｸﾚｰﾝ等でもち上げ､ 取付け全てを油砥石で均し､①に組付ける(BOLT で固定)", "2.組付け後､加工面には金ﾆｽを塗布すること｡" ], "WorkPoints": [ "ﾋﾟﾝに当てつけて組付けて固定する事", "ﾋﾟﾝに当てつけて組付けて固定する事", "隙間:0.01mm未満", "この作業ではP1用･P2用の2ｾｯﾄ作成の事｡(仕様によりP2無しの仕様も有り)" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "◆作業者安全作業", "検査表①:駆動部ﾌﾚｰﾑ規正ﾋﾟﾝ隙間確認" ] }
{ "QualityItem": "塗布確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布されている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.01㎜", "ToolOther": "", "WorkName": "ﾍｯﾄﾞ駆動部組付け", "WorkItems": [ "◆1.⑥をｸﾚｰﾝ等でもち上げ､ 取付け全てを油砥石で均し､①に組付ける(BOLT で固定)", "2.組付け後､加工面には金ﾆｽを塗布すること｡" ], "WorkPoints": [ "ﾋﾟﾝに当てつけて組付けて固定する事", "ﾋﾟﾝに当てつけて組付けて固定する事", "隙間:0.01mm未満", "この作業ではP1用･P2用の2ｾｯﾄ作成の事｡(仕様によりP2無しの仕様も有り)" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "◆作業者安全作業", "検査表①:駆動部ﾌﾚｰﾑ規正ﾋﾟﾝ隙間確認" ] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "隙間:0.01㎜未満", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞ駆動部背面組付け", "WorkItems": [ "1. ①に⑥をBOLT WASHER で組付け" ], "WorkPoints": [ "この作業ではP1用･P2用の2ｾｯﾄ作成の事｡(仕様によりP2無しの仕様も有り)" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞ駆動部上面組付け", "WorkItems": [ "1. ⑥にBRACKET BRACKET CABLE-SUPPORT をBOLT WASHER BOLT WASHER で組付け" ], "WorkPoints": [ "この作業ではP1用･P2用の2ｾｯﾄ作成の事｡(仕様によりP2無しの仕様も有り)" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "加圧ｼﾘﾝﾀﾞｰﾕﾆｯﾄ組込", "WorkItems": [ "1.①に⑥をBOLT で取付", "2.⑥にJOINT 取付ける｡", "3.⑥にWASHER NUT を取付ける｡" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "5.2㎜" ] }
{ "QualityItem": "PIN出代", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "出代:5.2㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞ_ﾍﾞｰｽﾕﾆｯﾄ組付け", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "1/100", "ToolOther": "", "WorkName": "ﾍｯﾄﾞ_ﾍﾞｰｽﾕﾆｯﾄの平行・隙間確認", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-064", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-064" ] }
{ "QualityItem": "平行度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "0.01㎜以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5300-064", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.01㎜", "ToolOther": "", "WorkName": "ﾍｯﾄﾞ_ﾍﾞｰｽﾕﾆｯﾄの平行・隙間確認", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "隙間:0.01㎜未満", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "Size": "20㎜", "ToolOther": "", "WorkName": "加圧ｼﾘﾝﾀﾞｰﾕﾆｯﾄのﾋﾟｯﾁ確認", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "隙間:20㎜", "Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾕﾆｯﾄ組付け", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｼﾘﾝﾀﾞｰﾛｯﾄﾞとﾍｯﾄﾞﾌﾞﾗｹｯﾄの隙間・切替動作確認", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-061", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-061" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "WWYJ-5300-061", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｼﾘﾝﾀﾞｰﾛｯﾄﾞとﾍｯﾄﾞﾌﾞﾗｹｯﾄの隙間・切替動作確認", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "動作確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ﾍｯﾄﾞｽﾗｲﾄﾞ時に過大な負荷のかからないこと", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "2/1000", "ToolOther": "", "WorkName": "本圧着ﾂｰﾙ前端面のﾍｯﾄﾞ間平行・ﾍｯﾄﾞ内平行確認", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-061", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-061" ] }
{ "QualityItem": "平行度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "±0.05㎜以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5300-061", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "2/1000", "ToolOther": "", "WorkName": "本圧着ﾂｰﾙ前端面のﾍｯﾄﾞ間平行・ﾍｯﾄﾞ内平行確認", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "平行度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "±0.02㎜以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.01㎜", "ToolOther": "", "WorkName": "ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞ部組付け", "WorkItems": [ "1. ①に⑥を㉓BOLT で組付け" ], "WorkPoints": [ "この作業ではP1用･P2用の2ｾｯﾄ作成の事｡(仕様によりP2無しの仕様も有り)", "･組付け方向に注意する･ﾋﾟﾝに当付いている事(ﾋﾟﾝの隙間:0.01㎜以下)", "⑥と①のﾋﾟﾝ間を確認する", "ﾋｰﾀｰ線､ﾋｭｰｽﾞが裏になる様組付け" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "隙間:0.01㎜以下", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾌﾞﾚｰｷ解除治具", "Size": "", "ToolOther": "FM-3229", "WorkName": "ﾊﾞｯｸｱｯﾌﾟﾂｰﾙ位置調整①", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-061", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-061" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "FM-3229", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "-", "Method": "-", "RecordMethod": "WWYJ-5300-061", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "2/1000", "ToolOther": "", "WorkName": "ﾊﾞｯｸｱｯﾌﾟﾂｰﾙ位置調整①", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "寸法:ｽﾃﾝﾚｽ0.25~0.30㎜,ｶﾞﾗｽ0.35~0.40㎜", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "測定台", "Size": "", "ToolOther": "FM-2249", "WorkName": "ﾊﾞｯｸｱｯﾌﾟﾂｰﾙ位置調整①", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "FM-2249", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "-", "Method": "-", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "2/1000", "ToolOther": "", "WorkName": "ﾊﾞｯｸｱｯﾌﾟﾂｰﾙ位置調整①", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "寸法:0.02㎜以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "2/1000", "ToolOther": "", "WorkName": "ﾊﾞｯｸｱｯﾌﾟﾂｰﾙ位置調整①", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "寸法:0.03㎜以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.01㎜", "ToolOther": "", "WorkName": "ﾊﾞｯｸｱｯﾌﾟﾂｰﾙ位置調整②", "WorkItems": [ "1. ①のﾊﾞｯｸｱｯﾌﾟﾕﾆｯﾄ 規正ﾋﾟﾝ隙間確認" ], "WorkPoints": [ "この作業ではP1用･P2用の2ｾｯﾄ作成の事｡(仕様によりP2無しの仕様も有り)", "本圧着ﾌﾚｰﾑ部ﾍﾞｰｽ左側面のﾋﾟﾝとの隙間を確認する", "0.01mm未満" ], "Tolks": [], "InspectionNo": "WWYJ-5300-061", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:ﾊﾞｯｸｱｯﾌﾟﾕﾆｯﾄ 規正ﾋﾟﾝ隙間確認", "本圧着ﾌﾚｰﾑﾍﾞｰｽ", "<本圧着ﾌﾚｰﾑ部前面>", "本圧着ﾊﾞｯｸｱｯﾌﾟﾍﾞｰｽ", "N002 PIN", "WWYJ-5300-061" ] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "隙間:0.01㎜未満", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5300-061", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "保護ｼｰﾄ送り部組付け①", "WorkItems": [ "1. ①に⑥をBOLT で組付け" ], "WorkPoints": [ "この作業ではP1用･P2用の2ｾｯﾄ作成の事｡(仕様によりP2無しの仕様も有り)", "K032の左側用", "K032の右側用", "配線･配管は後ろへ引き回す", "配線･配管は後ろへ引き回す" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "保護ｼｰﾄ送り部組付け②", "WorkItems": [ "1. ①に⑥⑦をBOLT で組付け" ], "WorkPoints": [ "裏側図", "この作業ではP1用･P2用の2ｾｯﾄ作成の事｡(仕様によりP2無しの仕様も有り)", "裏側図", "⑦がDﾋﾟﾝに当付いている事", "⑥がDﾋﾟﾝに当付いている事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "保護ｼｰﾄ送り部組付け③", "WorkItems": [ "1. ①に⑥をBOLT で組付け", "2. ⑥にCOVER をBOLT ㉒で組付け" ], "WorkPoints": [ "この作業ではP1用･P2用の2ｾｯﾄ作成の事｡(仕様によりP2無しの仕様も有り)", "①裏側図", "⑥をﾌﾚｰﾑのﾋﾟﾝに挿入し固定" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾊﾟﾈﾙ認識光学系(×1)P組付け①", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.01㎜", "ToolOther": "", "WorkName": "ﾊﾟﾈﾙ認識光学系(×1)P組付け②", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-061", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-061" ] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "隙間:0.01㎜未満", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5300-061", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "600㎜", "ToolOther": "", "WorkName": "ﾊﾟﾈﾙ認識光学系(×1)P組付け②", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法:374.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "本圧着ｲｵﾅｲｻﾞｰP組付け", "WorkItems": [ "1. ⑥に①をBOLT WASHER で組付け", "2. ⑥に②をBOLT WASHER WASHER で組付け" ], "WorkPoints": [ "この作業ではP1用･P2用の2ｾｯﾄ作成の事｡(仕様によりP2無しの仕様も有り)", "①裏側図", "取付方向注意" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "冷却ﾌﾞﾛｰｽﾋﾟｺﾝﾌﾞﾗｹｯﾄ(OP)組付け", "WorkItems": [ "1. ①に⑥⑦をBOLT WASHER で組付け", "2. ①に⑧を㉒で組付け" ], "WorkPoints": [ "この作業ではP1用･P2用の2ｾｯﾄ作成の事｡(仕様によりP2無しの仕様も有り)", "①表側図", "上から見た図", "①裏側図" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "Size": "1㎜", "ToolOther": "", "WorkName": "本圧着ﾍｯﾄﾞ加圧ｼﾘﾝﾀﾞｰ確認", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-061", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-061" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法:ON1.0㎜OFF2.0㎜", "Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5300-061", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｾﾝｻｰﾁｪｯｶｰ", "Size": "", "ToolOther": "FM-2375", "WorkName": "本圧着保護ｼｰﾄ送り部確認", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-061", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-061" ] }
{ "QualityItem": "位置確認", "ToolManageNo": "FM-2375", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示位置であること", "Method": "目視", "RecordMethod": "WWYJ-5300-061", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌｪﾗｲﾄｺｱ準備①(本圧着部P1)", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-184", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-184" ] }
{ "QualityItem": "型式確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式が一致する事", "Method": "目視", "RecordMethod": "WWYJ-5300-184", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌｪﾗｲﾄｺｱ準備②(本圧着ﾍｯﾄﾞ部P14本仕様)", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-184", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-184" ] }
{ "QualityItem": "型式確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式が一致する事", "Method": "目視", "RecordMethod": "WWYJ-5300-184", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌｪﾗｲﾄｺｱ準備③(本圧着ﾍｯﾄﾞ部P1L3/R3OP)", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-184", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-184" ] }
{ "QualityItem": "型式確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式が一致する事", "Method": "目視", "RecordMethod": "WWYJ-5300-184", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌｪﾗｲﾄｺｱ準備④(本圧着ﾍｯﾄﾞ部P1L4/R4OP)", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-184", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-184" ] }
{ "QualityItem": "型式確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式が一致する事", "Method": "目視", "RecordMethod": "WWYJ-5300-184", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌｪﾗｲﾄｺｱ準備⑤(本圧着ｲｵﾅｲｻﾞｰ部P1OP)", "WorkItems": [ "■1. NOISE-FILTER の型式を確認し､LABEL TERMINAL PROCESS を貼付けする(ｵﾌﾟｼｮﾝ)" ], "WorkPoints": [ "型式ﾁｪｯｸ" ], "Tolks": [], "InspectionNo": "WWYJ-5300-184", "InspectionItems": [ "検査表①:型式ﾁｪｯｸ" ], "WorkTypes": [], "Words": [ "R246\tP1本圧着ｲｵﾅｲｻﾞｰ線", "R246", "WWYJ-5300-184" ] }
{ "QualityItem": "型式確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式が一致する事", "Method": "目視", "RecordMethod": "WWYJ-5300-184", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌｪﾗｲﾄｺｱ準備⑥(本圧着部P2)", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-185", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-185" ] }
{ "QualityItem": "型式確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式が一致する事", "Method": "目視", "RecordMethod": "WWYJ-5300-185", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌｪﾗｲﾄｺｱ準備⑦(本圧着ﾍｯﾄﾞ部P24本仕様)", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-185", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-185" ] }
{ "QualityItem": "型式確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式が一致する事", "Method": "目視", "RecordMethod": "WWYJ-5300-185", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌｪﾗｲﾄｺｱ準備⑧(本圧着ﾍｯﾄﾞ部P2L3/R3OP)", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-185", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-185" ] }
{ "QualityItem": "型式確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式が一致する事", "Method": "目視", "RecordMethod": "WWYJ-5300-185", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌｪﾗｲﾄｺｱ準備⑨(本圧着ﾍｯﾄﾞ部P2L4/R4OP)", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-185", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-185" ] }
{ "QualityItem": "型式確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式が一致する事", "Method": "目視", "RecordMethod": "WWYJ-5300-185", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌｪﾗｲﾄｺｱ準備⑩(本圧着ｲｵﾅｲｻﾞｰ部P2OP)", "WorkItems": [ "■1. NOISE-FILTER の型式を確認し､LABEL TERMINAL PROCESS を貼付けする(ｵﾌﾟｼｮﾝ)" ], "WorkPoints": [ "型式ﾁｪｯｸ", "(仕様によりP2無しの仕様も有り)" ], "Tolks": [], "InspectionNo": "WWYJ-5300-185", "InspectionItems": [ "検査表①:型式ﾁｪｯｸ" ], "WorkTypes": [], "Words": [ "R247\tP2本圧着ｲｵﾅｲｻﾞｰ線", "R247", "WWYJ-5300-185" ] }
{ "QualityItem": "型式確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式が一致する事", "Method": "目視", "RecordMethod": "WWYJ-5300-185", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾍｯﾄﾞﾓｰﾀｰｹｰﾌﾞﾙ接続", "WorkItems": [ "1. ①ﾍｯﾄﾞﾓｰﾀｰｹｰﾌﾞﾙにCABLE CABLE CABLE CABLE CABLE CABLE を接続する" ], "WorkPoints": [ "この作業ではP1用･P2用の2ｾｯﾄ作成の事｡(仕様によりP2無しの仕様も有り)", "裏側図" ], "Tolks": [], "InspectionNo": "WWYJ-5300-128", "InspectionItems": [ "検査表①:接続確認 (2) P1H軸ﾓｰﾀｰ" ], "WorkTypes": [], "Words": [ "P2", "P1", "前:EM4210R奥:EM4210P", "前:BM4210R奥:BM4210P", "前:MM4210R奥:MM4210P", "検査表②:接続確認 (2) P2H軸ﾓｰﾀｰ", "前:EM4310R奥:EM4310P", "前:BM4310R奥:BM4310P", "前:MM4310R奥:MM4310P", "P2", "P1", "P2", "P1", "P2", "P1", "WWYJ-5300-128" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "WWYJ-5300-128", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null