input stringclasses 1 value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "22㎜",
"ToolOther": "8.7N･m",
"WorkName": "X軸ﾌﾚｰﾑ部組立③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 8.7N･m"
],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [
"検査表①:◆X軸組立 ﾎﾞｰﾙﾈｼﾞへのﾍﾞｱﾘﾝｸﾞ組付"
],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "8.7N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立④",
"WorkItems": [
"1. ①X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄの平行出し",
"2. 1.完成品のﾎﾞｰﾙﾈｼﾞ部の精度出し後ｽﾄｯﾊﾟｰﾌﾞﾛｯｸを本締め"
],
"WorkPoints": [
"X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ",
"平行度:0.01㎜以下",
"調整後本締め",
"X軸ﾎﾞｰﾙﾈｼﾞ",
"基準LM",
"平行度:0.01㎜以下",
"水平度:0.02㎜以下(参考値)",
"基準LM",
"水平方向(上面)",
"平行方向(側面)",
"L･R共にﾓｰﾀｰﾌﾞﾗｹｯﾄの両端を測定する事(赤色部分)",
"L･R共に測定する事",
"調整後本締め"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [
"検査表①:X軸組立 ﾎﾞｰﾙﾈｼﾞ組込"
],
"WorkTypes": [],
"Words": [
"検査表①:◆X軸組立 ﾎﾞｰﾙﾈｼﾞ組込",
"1.完成品",
"WWYJ-5300-049"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.01㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立④",
"WorkItems": [
"1. ①X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄの平行出し",
"2. 1.完成品のﾎﾞｰﾙﾈｼﾞ部の精度出し後ｽﾄｯﾊﾟｰﾌﾞﾛｯｸを本締め"
],
"WorkPoints": [
"X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ",
"平行度:0.01㎜以下",
"調整後本締め",
"X軸ﾎﾞｰﾙﾈｼﾞ",
"基準LM",
"平行度:0.01㎜以下",
"水平度:0.02㎜以下(参考値)",
"基準LM",
"水平方向(上面)",
"平行方向(側面)",
"L･R共にﾓｰﾀｰﾌﾞﾗｹｯﾄの両端を測定する事(赤色部分)",
"L･R共に測定する事",
"調整後本締め"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [
"検査表①:◆X軸組立 ﾎﾞｰﾙﾈｼﾞ組込"
],
"WorkTypes": [],
"Words": [
"検査表①:X軸組立 ﾎﾞｰﾙﾈｼﾞ組込",
"1.完成品",
"WWYJ-5300-049"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.01㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立④",
"WorkItems": [
"1. ①X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄの平行出し",
"2. 1.完成品のﾎﾞｰﾙﾈｼﾞ部の精度出し後ｽﾄｯﾊﾟｰﾌﾞﾛｯｸを本締め"
],
"WorkPoints": [
"X軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ",
"平行度:0.01㎜以下",
"調整後本締め",
"X軸ﾎﾞｰﾙﾈｼﾞ",
"基準LM",
"平行度:0.01㎜以下",
"水平度:0.02㎜以下(参考値)",
"基準LM",
"水平方向(上面)",
"平行方向(側面)",
"L･R共にﾓｰﾀｰﾌﾞﾗｹｯﾄの両端を測定する事(赤色部分)",
"L･R共に測定する事",
"調整後本締め"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:X軸組立 ﾎﾞｰﾙﾈｼﾞ組込",
"検査表①:◆X軸組立 ﾎﾞｰﾙﾈｼﾞ組込",
"1.完成品",
"WWYJ-5300-049"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.02㎜以下(参考値)",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/1000",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立⑤",
"WorkItems": [
"1. ①ﾎﾞｰﾙﾈｼﾞ部ｽﾗｽﾄ方向ｶﾞﾀ確認",
"2. 1.完成品のﾎﾞｰﾙﾈｼﾞ部の芯振れの確認"
],
"WorkPoints": [
"L･R共に測定する事",
"L･R共に測定する事",
"ﾈｼﾞ端部を30Nの力で押す"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [
"検査表①:X軸組立 ﾎﾞｰﾙﾈｼﾞｶﾞﾀ確認"
],
"WorkTypes": [],
"Words": [
"検査表①:◆X軸組立 ﾎﾞｰﾙねじの芯振れ",
"WWYJ-5300-049"
]
} | {
"QualityItem": "ｽﾗｽﾄ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.01㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/1000",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立⑤",
"WorkItems": [
"1. ①ﾎﾞｰﾙﾈｼﾞ部ｽﾗｽﾄ方向ｶﾞﾀ確認",
"2. 1.完成品のﾎﾞｰﾙﾈｼﾞ部の芯振れの確認"
],
"WorkPoints": [
"L･R共に測定する事",
"L･R共に測定する事",
"ﾈｼﾞ端部を30Nの力で押す"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [
"検査表①:◆X軸組立 ﾎﾞｰﾙねじの芯振れ"
],
"WorkTypes": [],
"Words": [
"検査表①:X軸組立 ﾎﾞｰﾙﾈｼﾞｶﾞﾀ確認",
"WWYJ-5300-049"
]
} | {
"QualityItem": "芯ﾌﾞﾚ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.02㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立⑥",
"WorkItems": [
"◆1. ①にSCREW を取付しSPACER を取付",
"◆2. 1.完成品にSCREW を取付しSPACER を取付",
"3. 2.完成品にBLOCK BLOCK BLOCK BLOCK をBOLT で取付",
"4. 3.完成品にSENSOR をBOLT WASHER WASHER で取付"
],
"WorkPoints": [
"㉖ロックタイト塗布",
"㉖ロックタイト塗布"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×20",
"接着剤塗布 ｺﾞﾏ粒:2",
"側面図",
"側面図",
"1.完成品",
"×2",
"×16",
"2.完成品",
"側面図",
"3.完成品"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾑ粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立⑦",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "正常な事(引っ掛かり等無き事)",
"Method": "目視",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾝｼｮﾝｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立⑦",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "摺動確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "40cN・m以下ﾊﾞﾗﾂｷ15cN・m以下",
"Method": "ﾄﾙｸｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ﾌﾚｰﾑ部組立⑧",
"WorkItems": [
"1. ①の配管干渉をチェックし㉖で結束",
"2. 1.完成品の配管を②･③に接続"
],
"WorkPoints": [
"LMﾚｰﾙやﾎﾞｰﾙねじ等と接触し無い事を確認",
"L･R共に確認する事"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [
"検査表①:◆X軸組立 配管の干渉ﾁｪｯｸ"
],
"WorkTypes": [],
"Words": [
"ﾌﾟﾚｰﾄ(L側)",
"ﾌﾟﾚｰﾄ(R側)",
"1.完成品",
"①LM給油用",
"②LM給油用",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ﾌﾟﾚｰﾄ(L側)",
"ﾌﾟﾚｰﾄ(R側)",
"L側ﾌﾟﾚｰﾄ",
"R側ﾌﾟﾚｰﾄ",
"手前側ｶﾞｲﾄﾞ",
"ﾎﾞｰﾙﾈｼﾞ",
"奥側ｶﾞｲﾄﾞ",
"手前側ｶﾞｲﾄﾞ",
"ﾎﾞｰﾙﾈｼﾞ",
"奥側ｶﾞｲﾄﾞ",
"L側ﾌﾟﾚｰﾄ",
"R側ﾌﾟﾚｰﾄ",
"③ﾎﾞｰﾙねじ用",
"WWYJ-5300-049"
]
} | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "LMﾚｰﾙやﾎﾞｰﾙねじ等と接触し無い事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立①",
"WorkItems": [
"1. BASE-FRAME(Y) の表面にPIN LINEAR-WAY を圧入",
"2. ④の重要部品の確認",
"3. ④に塗布されている防錆油を拭取る"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを1組(2個)製作 (L･R区分必要)",
"2.5㎜"
]
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:2.5㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立①",
"WorkItems": [
"1. BASE-FRAME(Y) の表面にPIN LINEAR-WAY を圧入",
"2. ④の重要部品の確認",
"3. ④に塗布されている防錆油を拭取る",
"4. 1.完成品に3.完成品をBOLT で仮固定する"
],
"WorkPoints": [
"型式確認及び､ｼﾘｱﾙ№記録",
"出代:5㎜",
"出代:2.5㎜",
"LMｶﾞｲﾄﾞ基準面(加工面)を内側に取付ける",
"本締め工程:SD-A044837-025",
"LMｶﾞｲﾄﾞ基準面(従動側)",
"LMｶﾞｲﾄﾞ基準面(KB側)",
"ﾏｽｷﾝｸﾞﾃｰﾌﾟでL･R区分明記"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [
"検査表BASE-FRAME(Y) :部品確認"
],
"WorkTypes": [],
"Words": [
"この作業では同じものを1組(2個)製作 (L･R区分必要)",
"1.完成品",
"5㎜",
"2.5㎜",
"×40",
"3.完成品",
"WWYJ-5300-049"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立①",
"WorkItems": [
"1. BASE-FRAME(Y) の表面にPIN LINEAR-WAY を圧入",
"2. ④の重要部品の確認",
"3. ④に塗布されている防錆油を拭取る",
"4. 1.完成品に3.完成品をBOLT で仮固定する"
],
"WorkPoints": [
"型式確認及び､ｼﾘｱﾙ№記録",
"出代:5㎜",
"出代:2.5㎜",
"LMｶﾞｲﾄﾞ基準面(加工面)を内側に取付ける",
"本締め工程:SD-A044837-025",
"LMｶﾞｲﾄﾞ基準面(従動側)",
"LMｶﾞｲﾄﾞ基準面(KB側)",
"ﾏｽｷﾝｸﾞﾃｰﾌﾟでL･R区分明記"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを1組(2個)製作 (L･R区分必要)",
"1.完成品",
"5㎜",
"2.5㎜",
"検査表BASE-FRAME(Y) :部品確認",
"×40",
"3.完成品",
"WWYJ-5300-049"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立①",
"WorkItems": [
"1. BASE-FRAME(Y) の表面にPIN LINEAR-WAY を圧入",
"2. ④の重要部品の確認",
"3. ④に塗布されている防錆油を拭取る",
"4. 1.完成品に3.完成品をBOLT で仮固定する"
],
"WorkPoints": [
"型式確認及び､ｼﾘｱﾙ№記録",
"出代:5㎜",
"出代:2.5㎜",
"LMｶﾞｲﾄﾞ基準面(加工面)を内側に取付ける",
"本締め工程:SD-A044837-025",
"LMｶﾞｲﾄﾞ基準面(従動側)",
"LMｶﾞｲﾄﾞ基準面(KB側)",
"ﾏｽｷﾝｸﾞﾃｰﾌﾟでL･R区分明記"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを1組(2個)製作 (L･R区分必要)",
"1.完成品",
"5㎜",
"2.5㎜",
"検査表BASE-FRAME(Y) :部品確認",
"×40",
"3.完成品"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "5㎜",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立②",
"WorkItems": [],
"WorkPoints": [
"従動側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立②",
"WorkItems": [],
"WorkPoints": [
"従動側",
"従動側"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"1.完成品",
"WWYJ-5300-049"
]
} | {
"QualityItem": "真直度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.01㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立②",
"WorkItems": [],
"WorkPoints": [
"従動側",
"従動側"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"1.完成品",
"WWYJ-5300-049"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.01㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "N･m",
"WorkName": "Y軸ﾌﾚｰﾑ部組立②",
"WorkItems": [],
"WorkPoints": [
"従動側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立②",
"WorkItems": [],
"WorkPoints": [
"従動側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "寸法:190㎜±1㎜以内",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立③",
"WorkItems": [
"1. ①･②に③をBOLT ･BOLT で仮固定",
"2. 1.完成品に④･⑤を挿入しBLOCK ･BOLT で仮固定",
"3. 2.完成品にWASHER を挿入しNUT で締付"
],
"WorkPoints": [
"本締め工程:SD-A044837-027",
"本締め工程:SD-A044837-027",
"付属ｾｯﾄﾋﾞｽ(PICE含)",
"ﾅｯﾄ段付き部",
"NUT ﾅｯﾄの段付側をWASHER ｶﾗｰ側に向けて取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 6.9N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを1組製作 (L･R区分必要)",
"×2",
"1.完成品",
"×2",
"×2",
"検査表①:Y軸組立 ﾎﾞｰﾙﾈｼﾞへのﾍﾞｱﾘﾝｸﾞ組付"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "19㎜",
"ToolOther": "6.9N･m",
"WorkName": "Y軸ﾌﾚｰﾑ部組立③",
"WorkItems": [],
"WorkPoints": [
"付属ｾｯﾄﾋﾞｽ(PICE含)",
"ﾅｯﾄ段付き部",
"NUT ﾅｯﾄの段付側をWASHER ｶﾗｰ側に向けて取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 6.9N･m"
],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.9N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.01㎜以下(ﾓｰﾀｰﾌﾞﾗｹｯﾄ)",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.01㎜以下(ﾎﾞｰﾙﾈｼﾞ)",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "2/1000",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立④",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.02㎜以下(参考値)",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/1000",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立⑤",
"WorkItems": [
"1. ①･②ﾎﾞｰﾙﾈｼﾞ部ｽﾗｽﾄ方向ｶﾞﾀ確認",
"2. 1.完成品のﾎﾞｰﾙﾈｼﾞ部の芯振れの確認"
],
"WorkPoints": [
"Y軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ",
"ｽﾗｽﾄｶﾞﾀ:0.001㎜以下",
"芯振れ:0.01㎜以下",
"Y軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [
"検査表①:Y軸組立 ﾎﾞｰﾙﾈｼﾞｶﾞﾀ確認"
],
"WorkTypes": [],
"Words": [
"この作業では同じものを1組製作 (L･R区分必要)",
"検査表①:◆Y軸組立 ﾎﾞｰﾙねじの芯振れ",
"WWYJ-5300-049"
]
} | {
"QualityItem": "ｽﾗｽﾄ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.001㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/1000",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立⑤",
"WorkItems": [
"1. ①･②ﾎﾞｰﾙﾈｼﾞ部ｽﾗｽﾄ方向ｶﾞﾀ確認",
"2. 1.完成品のﾎﾞｰﾙﾈｼﾞ部の芯振れの確認"
],
"WorkPoints": [
"Y軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ",
"ｽﾗｽﾄｶﾞﾀ:0.001㎜以下",
"芯振れ:0.01㎜以下",
"Y軸ﾓｰﾀｰﾌﾞﾗｹｯﾄ"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [
"検査表①:◆Y軸組立 ﾎﾞｰﾙねじの芯振れ"
],
"WorkTypes": [],
"Words": [
"この作業では同じものを1組製作 (L･R区分必要)",
"検査表①:Y軸組立 ﾎﾞｰﾙﾈｼﾞｶﾞﾀ確認",
"WWYJ-5300-049"
]
} | {
"QualityItem": "芯ﾌﾞﾚ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.01㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立⑥",
"WorkItems": [
"1. ①･②にFRAME ･FRAME をBOLT ･WASHER で取付",
"2. 1.完成品にBRACKET をBOLT ･WASHER で取付",
"3. 2.完成品にSCREW ･NUT ･WASHER ･STOPPER を取付"
],
"WorkPoints": [
"ﾓｰﾀｰ側側面図",
"反対側側面図",
"L用",
"R用",
"ﾓｰﾀｰ側側面図",
"ﾓｰﾀｰ側側面図",
"L用のみ取付",
"ﾓｰﾀｰ側側面図",
"上面図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを1組製作 (L･R区分必要)",
"L用･R用共に同じ"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:30.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立⑦",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "引っかかり等無い事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃﾝｼｮﾝｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立⑦",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "摺動確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "25cN・m以下ﾊﾞﾗﾂｷ10cN・m以下",
"Method": "ﾄﾙｸｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立⑧",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/1000",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立⑨",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "真直度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.02㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/1000",
"ToolOther": "",
"WorkName": "Y軸ﾌﾚｰﾑ部組立⑨",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.03㎜以下(参考値)",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸ﾓｰﾀｰ取付",
"WorkItems": [
"1. ①にCOUPLING ･COUPLING を挿入し④･⑤をBOLT ･WASHER ･BOLT ･WASHER で取付"
],
"WorkPoints": [
"COUPLING ･COUPLING のｶｯﾌﾟﾘﾝｸﾞは締め付け無い事",
"COUPLING COUPLING の取付方向に注意",
"Ⅹ軸ﾓｰﾀｰ(K006-1 L用)",
"Y軸ﾓｰﾀｰ(K006-2 L用)",
"Ⅹ軸ﾓｰﾀｰ(K006-1 R用)",
"Y軸ﾓｰﾀｰ(K006-2 R用)",
"配線の向きに注意",
"配線の向きに注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×4",
"×4",
"×4",
"×4",
"×4",
"×4"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾓｰﾀ原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "X軸原点調整",
"WorkItems": [
"1. ①のX軸ﾓｰﾀｰにﾓｰﾀｰ原点出し治具を接続",
"3. X軸原点の状態でｶｯﾌﾟﾘﾝｸﾞを締め付け",
"2. X軸の原点治具ﾋﾟﾝを挿入し Y軸ﾌﾟﾚｰﾄ側面を当てる"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [
"検査表①:ﾓｰﾀｰ固定 X軸の原点合わせ",
"検査表①:ﾓｰﾀｰ固定 X軸の原点合わせ",
"検査表①:ﾓｰﾀｰ固定 X軸の原点合わせ"
],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "原点出しﾋﾟﾝ(φ12-φ8段付きﾋﾟﾝ)",
"Size": "",
"ToolOther": "FM-3467",
"WorkName": "X軸原点調整",
"WorkItems": [
"1. ①のX軸ﾓｰﾀｰにﾓｰﾀｰ原点出し治具を接続",
"3. X軸原点の状態でｶｯﾌﾟﾘﾝｸﾞを締め付け",
"2. X軸の原点治具ﾋﾟﾝを挿入し Y軸ﾌﾟﾚｰﾄ側面を当てる"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾓｰﾀｰ固定 X軸の原点合わせ",
"検査表①:ﾓｰﾀｰ固定 X軸の原点合わせ",
"検査表①:ﾓｰﾀｰ固定 X軸の原点合わせ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3467",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "22㎜",
"ToolOther": "63.7N･m",
"WorkName": "X軸原点調整",
"WorkItems": [
"1. ①のX軸ﾓｰﾀｰにﾓｰﾀｰ原点出し治具を接続",
"3. X軸原点の状態でｶｯﾌﾟﾘﾝｸﾞを締め付け",
"2. X軸の原点治具ﾋﾟﾝを挿入し Y軸ﾌﾟﾚｰﾄ側面を当てる"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [
"検査表①:ﾓｰﾀｰ固定 X軸の原点合わせ",
"検査表①:ﾓｰﾀｰ固定 X軸の原点合わせ",
"検査表①:ﾓｰﾀｰ固定 X軸の原点合わせ"
],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "ﾓｰﾀｰ側63.7N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "19㎜",
"ToolOther": "39.2N･m",
"WorkName": "X軸原点調整",
"WorkItems": [
"1. ①のX軸ﾓｰﾀｰにﾓｰﾀｰ原点出し治具を接続",
"3. X軸原点の状態でｶｯﾌﾟﾘﾝｸﾞを締め付け",
"2. X軸の原点治具ﾋﾟﾝを挿入し Y軸ﾌﾟﾚｰﾄ側面を当てる"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [
"検査表①:ﾓｰﾀｰ固定 X軸の原点合わせ",
"検査表①:ﾓｰﾀｰ固定 X軸の原点合わせ",
"検査表①:ﾓｰﾀｰ固定 X軸の原点合わせ"
],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "ﾈｼﾞ側39.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "X軸原点調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"7㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:155.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾓｰﾀ原点出し治具",
"Size": "",
"ToolOther": "FM-3446",
"WorkName": "Y軸原点調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3446",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "原点出しﾋﾟﾝ(φ12-φ8段付きﾋﾟﾝ)",
"Size": "",
"ToolOther": "FM-3467",
"WorkName": "Y軸原点調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "原点確認",
"ToolManageNo": "FM-3467",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "原点位置である事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "17㎜",
"ToolOther": "19.6N･m",
"WorkName": "Y軸原点調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "19.6N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "22㎜",
"ToolOther": "34.3N･m",
"WorkName": "Y軸原点調整",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "34.3N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｾﾝｻｰﾁｪｯｶｰ",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸原点調整",
"WorkItems": [
"1. ①のY軸ﾓｰﾀｰにﾓｰﾀｰ原点出し治具を接続",
"3. Y軸原点の状態でｶｯﾌﾟﾘﾝｸﾞを締め付け",
"2. Y軸の原点治具ﾋﾟﾝを挿入し Y軸ﾌﾟﾚｰﾄ側面を当てる",
"4. Y軸原点の状態でﾄﾞｸﾞ位置を調整する"
],
"WorkPoints": [
"L･R共に実施の事",
"ﾓｰﾀｰ側から規定ﾄﾙｸで締結の事",
"ﾓｰﾀｰ原点にする",
"原点PHｾﾝｻｰ位置を確認する",
"L･R共に実施の事",
"L･R共に実施の事"
],
"Tolks": [
"締付ﾄﾙｸ:ﾓｰﾀｰ側 34.3N･m",
"締付ﾄﾙｸ:ﾈｼﾞ側 19.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:◆ﾓｰﾀｰ固定Y軸の原点合わせ",
"検査表①:◆ﾓｰﾀｰ固定 Y軸の原点合わせ",
"検査表①:◆ﾓｰﾀｰ固定 Y軸の原点合わせ",
"検査表①:◆ﾓｰﾀｰ固定 Y軸の原点合わせ",
"4㎜",
"WWYJ-5300-049"
]
} | {
"QualityItem": "位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示位置であること",
"Method": "目視",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱｶﾞｲﾄﾞ・ﾎﾞｰﾙﾈｼﾞ部ｸﾞﾘｰｽ給油",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "X軸LM複数回ﾎﾟﾝﾌﾟしLMに届かせ指示箇所に薄く塗布",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱｶﾞｲﾄﾞ・ﾎﾞｰﾙﾈｼﾞ部ｸﾞﾘｰｽ給油",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "Y軸LM1回ﾎﾟﾝﾌﾟしLMに届かせ指示箇所に薄く塗布",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱｶﾞｲﾄﾞ・ﾎﾞｰﾙﾈｼﾞ部ｸﾞﾘｰｽ給油",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "X軸ﾎﾞｰﾙﾈｼﾞ複数回ﾎﾟﾝﾌﾟしﾎﾞｰﾙﾈｼﾞに届かせ指示箇所に薄く塗布",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱｶﾞｲﾄﾞ・ﾎﾞｰﾙﾈｼﾞ部ｸﾞﾘｰｽ給油",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "Y軸ﾎﾞｰﾙﾈｼﾞ複数回ﾎﾟﾝﾌﾟしﾎﾞｰﾙﾈｼﾞに届かせ指示箇所に薄く塗布",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾙﾈｼﾞｶﾊﾞｰ部取付①",
"WorkItems": [
"1. ①に②をPLATE ･PLATE ･BOLT で取付",
"2. 1.完成品に③をBOLT ･WASHER で取付"
],
"WorkPoints": [
"②が自重で撓むため 中央付近を上に持ち上げながらBOLT で締結"
],
"Tolks": [
"側面図",
"上面図",
"側面図",
"上面図"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×20",
"1.完成品",
"×8",
"1.完成品"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾙﾈｼﾞｶﾊﾞｰ部取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:4.0㎜±2.5㎜3.0㎜±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "測定治具",
"Size": "",
"ToolOther": "FM-6043",
"WorkName": "Zθﾃｰﾌﾞﾙ部取付①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6043",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "測定治具",
"Size": "",
"ToolOther": "FM-6043",
"WorkName": "Zθﾃｰﾌﾞﾙ部取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6043",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "Zθﾃｰﾌﾞﾙ部取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.2㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "Zθﾃｰﾌﾞﾙ部取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.02㎜以下0.05㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①に②･③をBOLT ･WASHER で取付",
"2. ①に④ ･⑤･⑥･⑦をBOLT ･WASHER ･BOLT ･WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"側面図"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×4",
"×10",
"×4",
"×4",
"×14"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙﾍﾞｱ取付",
"WorkItems": [
"1. ①にCABLE-BEAR SHEET をBOLT WASHER WASHER で取付",
"2. ①にCABLE-BEAR SHEET をBOLT WASHER WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"側面図",
"正面図",
"前面図"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×16",
"×8"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3.5m",
"ToolOther": "",
"WorkName": "Zθ配線・配管",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Zθ配線・配管",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｹｰﾌﾞﾙﾍﾞｱ前後の配管ｸﾗﾝﾌﾟ部分のねじれ、潰れ等無い事確認の事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸配線",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-109",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-109"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-109",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸配線",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WWYJ-5300-049"
]
} | {
"QualityItem": "干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｹｰﾌﾞﾙﾍﾞｱ前後の配管ｸﾗﾝﾌﾟ部分のねじれ、潰れ等無い事確認の事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸配線",
"WorkItems": [
"1. ①にCABLE ･CABLE を取付",
"3. 2.完成品の真空配管確認",
"2. 1.完成品の接続確認"
],
"WorkPoints": [
"L･R用共に確認の事",
"ｹｰﾌﾞﾙﾍﾞｱ入り口側から正圧(0.08MPa)を入れ､ 反対側の流量を測定 22~35L/min"
],
"Tolks": [
"前面図"
],
"InspectionNo": "WWYJ-5300-109",
"InspectionItems": [
"検査表②:接続確認 (1)MLX/MRX軸原点ｾﾝｻｰ"
],
"WorkTypes": [],
"Words": [
"<XYZθﾃｰﾌﾞﾙ部(M)のｹｰﾌﾞﾙ図>",
"【流量計接続箇所】",
"検査表①:配管確認 -2)流量確認",
"B10236R",
"B10237R",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WWYJ-5300-109"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-109",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸配線",
"WorkItems": [
"1. ①にCABLE ･CABLE を取付",
"3. 2.完成品の真空配管確認",
"2. 1.完成品の接続確認"
],
"WorkPoints": [
"L･R用共に確認の事",
"ｹｰﾌﾞﾙﾍﾞｱ入り口側から正圧(0.08MPa)を入れ､ 反対側の流量を測定 22~35L/min"
],
"Tolks": [
"前面図"
],
"InspectionNo": "WWYJ-5300-049",
"InspectionItems": [
"検査表①:配管確認 -2)流量確認"
],
"WorkTypes": [],
"Words": [
"<XYZθﾃｰﾌﾞﾙ部(M)のｹｰﾌﾞﾙ図>",
"【流量計接続箇所】",
"B10236R",
"B10237R",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表②:接続確認 (1)MLX/MRX軸原点ｾﾝｻｰ",
"WWYJ-5300-049"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｹｰﾌﾞﾙﾍﾞｱ入り口側から正圧(0.08MPa)を入れ、反対側の流量を測定22~35L/min",
"Method": "目視",
"RecordMethod": "WWYJ-5300-049",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①にCOVER COVER をBOLT で取付",
"2. 1.完成品にCOVER COVER COVER をSCREW で取付",
"3. 2.完成品にCOVER COVER をSCREW で取付"
],
"WorkPoints": [],
"Tolks": [
"Y軸上面図",
"X軸前面図",
"X軸上面図",
"Zθ軸上面図"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×20",
"1.完成品",
"×18",
"2.完成品",
"×8"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Zθ軸ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①にCOVER をSCREW で取付",
"2. 1.完成品にCOVER COVER COVER ⑩⑪をSCREW で取付"
],
"WorkPoints": [],
"Tolks": [
"Zθ軸背面図",
"Zθ軸左側面拡大図",
"Zθ軸背面図",
"Zθ軸右側面拡大図",
"Zθ軸前面",
"Zθ軸左側面",
"Zθ軸右側面",
"Zθ軸上面",
"Zθ軸前面",
"Zθ軸左側面",
"Zθ軸右側面",
"Zθ軸上面",
"Zθ軸背面",
"Zθ軸背面"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"1.完成品"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "払い出し",
"WorkItems": [
"1. ①~SPACER ･BOLT ~WASHER をMTKA045171(本体部)へ払い出し"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "払出確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示の払出である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θﾃｰﾌﾞﾙﾛｯｸ機構組立①",
"WorkItems": [],
"WorkPoints": [
"BLOCK ･BLOCK は1.完成品に押し当てながら固定",
"BLOCK ･BLOCK は1.完成品に押し当てながら固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "ﾋﾟﾝ出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代2.5±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "θﾃｰﾌﾞﾙﾛｯｸ機構組立②",
"WorkItems": [
"1. ①に②を取付",
"2. 1.完成品(L・R共)及びPIN ～CABLE-SUPPORT ・BOLT ～㉑をMTKA04388(Mテーブル用)へ払い出し"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業ではL･R用のものを各1個製作",
"仮止め:SD-A044838(305CG:Zθﾃｰﾌﾞﾙ)にて本締め",
"10㎜",
"端面合わせ",
"端面合わせ",
"10㎜",
"Lﾃｰﾌﾞﾙ用",
"Rﾃｰﾌﾞﾙ用"
]
} | {
"QualityItem": "ﾘｰﾄﾞSW寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "・端面より10±0.5㎜・端面合わせ(±0.5㎜)",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TCP供給部連結ﾌﾞﾗｹｯﾄ組立て",
"WorkItems": [
"1. BRACKET にSHAFT をBOLT で取付ける｡",
"2. BRACKET にBOLT WASHER (供給部連結用ﾎﾞﾙﾄ)を仮付けする｡",
"3. SHAFT にBOLT WASHER (供給部連結用ﾎﾞﾙﾄ)を仮付けする｡",
"4. 2.3の完成品をAM架台背面にBOLT WASHER で取付ける｡"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"AM架台背面",
"AM架台前面",
"AM架台上面図",
"2完成品",
"3完成品",
"ﾃｰﾌﾞﾙMX鋳物",
"ﾄﾚｲｽﾃｰｼﾞ TX軸"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｲｵﾅｲｻﾞｰ組立",
"WorkItems": [
"1. IONIZER 除電ﾊﾞｰ部にSPEED-CONTROLLER を取付け",
"3. 2の完成品にBRACKET をBOLT WASHER ㉒で取付け",
"4. PLATE にIONIZER コントローラ部をBOLT WASHER ㉒で取付け",
"5. NUT SUPPORT BOLT WASHER ､BLOCK BOLT WASHER を付属",
"2. IONIZER ｴﾝﾄﾞﾕﾆｯﾄを除電ﾊﾞｰ部に付属ﾈｼﾞで取付け"
],
"WorkPoints": [
"NUT BOLT WASHER は各4個",
"BLOCK BOLT WASHER は各2個"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｺﾝﾄﾛｰﾗ部",
"ｴﾝﾄﾞﾕﾆｯﾄ",
"付属ﾈｼﾞ",
"付属ﾈｼﾞ",
"ｴﾝﾄﾞﾕﾆｯﾄ",
"除電ﾊﾞｰ部"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｲｵﾅｲｻﾞｰ配線準備",
"WorkItems": [
"1. CABLE にLABEL TERMINAL PROCESS (LABEL TERMINAL PROCESS )を取付け",
"2. CABLE CABLE (CABLE CABLE )を付属"
],
"WorkPoints": [
"合わせる",
"合わせる",
"合わせる",
"合わせる",
"上流はCABLE CABLE ､下流はCABLE CABLE を付属",
"上流はLABEL TERMINAL PROCESS ､下流はLABEL TERMINAL PROCESS を取付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"上流",
"下流",
"BLACKE2005P",
"BLACKE2006P",
"E2006P",
"E2005P"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾏｸﾞﾈｯﾄ取付け",
"WorkItems": [
"1. ﾊｰﾈｽﾎﾞｰﾄﾞにﾏｸﾞﾈｯﾄを取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"⇒ﾏｸﾞﾈｯﾄ中",
"⇒ﾏｸﾞﾈｯﾄ大"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊｰﾈｽ準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.下記ﾘｽﾄの順番でｹｰﾌﾞﾙを準備する"
]
} | {
"QualityItem": "ｹｰﾌﾞﾙの準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"9X015",
"E1K4305",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"7X015",
"E1K4304",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回3",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"3X015",
"E1K4302",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回4",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"6X015",
"E1K4308",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回5",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"8X015",
"E1K4309",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回6",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"4X015",
"E1K4307",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回7",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"5X015",
"E1K4303",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回8",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"10X015",
"E1K4310",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回9",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"11X015",
"E1K4403",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回10",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1X015",
"E1K4301",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回11",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"P2SVD1P",
"XAK4301",
"XAK4403/XAK4402",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回12",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1X013",
"16X015",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回13",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"15X015",
"16X016",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回14",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"10X016",
"9X016",
"FGT161/-VeT161",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回15",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1aX1601/2aX1601/3aX1601/ACLaT161/ACNaT161",
"P2ACR",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回16",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"7X016",
"16X0501",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回17",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"P2SVD2R",
"XAK/4302/4304/4305/4303/4307/4309/4308",
"XAK4306",
"XAK4310",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ﾊｰﾈｽ引き回18",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"11X015",
"E1K4403",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6457",
"WorkName": "ｲﾝｼｭﾛｯｸ固定",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. ｲﾝｼｭﾛｯｸで固定する",
"⇒100mm",
"⇒150mm",
"⇒200mm",
"⇒250mm"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6457",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6459",
"WorkName": "ﾏｸﾞﾈｯﾄ取付け",
"WorkItems": [
"1. ﾊｰﾈｽﾎﾞｰﾄﾞにﾏｸﾞﾈｯﾄを取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"⇒ﾏｸﾞﾈｯﾄ中",
"⇒ﾏｸﾞﾈｯﾄ大"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6459",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊｰﾈｽ準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.下記ﾘｽﾄの順番でｹｰﾌﾞﾙを準備する"
]
} | {
"QualityItem": "ｹｰﾌﾞﾙの準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6459",
"WorkName": "ﾊｰﾈｽ引き回1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN8K00A",
"R30A40R/R30A41R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6459",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6459",
"WorkName": "ﾊｰﾈｽ引き回2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1G10B40-1R",
"G10B40P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6459",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6459",
"WorkName": "ﾊｰﾈｽ引き回3",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1G10B40-2R",
"G10B41P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6459",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6459",
"WorkName": "ﾊｰﾈｽ引き回4",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1G10B40-3R",
"G10B42P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6459",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6459",
"WorkName": "ﾊｰﾈｽ引き回5",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1G10B40-4R",
"G10B43P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6459",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6459",
"WorkName": "ﾊｰﾈｽ引き回6",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1G10B40-5R",
"G10B44P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6459",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6459",
"WorkName": "ﾊｰﾈｽ引き回7",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1G10B40-6R",
"G10B45P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6459",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6459",
"WorkName": "ﾊｰﾈｽ引き回8",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN10K00B",
"BX2112",
"1G10B30R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6459",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.