input stringclasses 1 value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Xﾋﾞｰﾑ仮取付け(FRONTｰ左側)",
"WorkItems": [
"1. 架台の切り欠け位置にｽﾗｲﾀﾞｰを合わせ 取付面及び基準面の清掃を行う",
"2. ｸﾞﾘｰｽﾆｯﾌﾟﾙの方向を確認する",
"3. ㉗を架台にセットする",
"◆4. ①をｽﾗｲﾄﾞさせながら載せる",
"5. ｽﾗｲﾀﾞｰとの位置を合わせ BOLT WASHER にて仮取付けする",
"6. ①を数回揺さぶってもらい取付け穴とﾎﾞﾙﾄのｾﾝﾀｰを確認し 基準(ﾍﾞｱ)側へ押し当ててもらう",
"7. ﾘｱ側作業者に押し当ててもらっている状態で4点仮締めをする"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側作業者",
"ﾘｱ側作業者",
"取付穴とﾎﾞﾙﾄのｾﾝﾀｰ確認",
"ﾎﾞﾙﾄを締付ける手前まで入れる",
"ﾎﾞﾙﾄのｾﾝﾀｰ確認後に締める",
"二人作業で行う",
"架台の内側に配管穴が向いてること"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "WEPJ-G002-C02",
"InspectionItems": [
"検査表①:4.Y軸ﾘﾆｱｶﾞｲﾄﾞのｸﾞﾘｰｽﾆｯﾌﾟﾙ方向確認"
],
"WorkTypes": [],
"Words": [
"FRONT",
"REAR",
"FRONT",
"REAR",
"FRONT",
"押し当ててもらう",
"数回揺さぶってもらう",
"仮止め:SD-EJM8EB1-054にて本締め",
"WEPJ-G002-C02"
]
} | {
"QualityItem": "方向確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りの方向に向いている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C02",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "治工具ﾋﾞｽ落下防止ﾏｯﾄ",
"Size": "",
"ToolOther": "FM-5829",
"WorkName": "Xﾋﾞｰﾑ仮取付け(FRONTｰ左側)",
"WorkItems": [
"1. 架台の切り欠け位置にｽﾗｲﾀﾞｰを合わせ 取付面及び基準面の清掃を行う",
"3. ㉗を架台にセットする",
"◆4. ①をｽﾗｲﾄﾞさせながら載せる"
],
"WorkPoints": [
"二人作業で行う"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT",
"REAR",
"FRONT",
"REAR",
"FRONT",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5829",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "Xﾋﾞｰﾑ仮取付け(FRONTｰ左側)",
"WorkItems": [
"2. ｸﾞﾘｰｽﾆｯﾌﾟﾙの方向を確認する",
"5. ｽﾗｲﾀﾞｰとの位置を合わせ BOLT WASHER にて仮取付けする",
"6. ①を数回揺さぶってもらい取付け穴とﾎﾞﾙﾄのｾﾝﾀｰを確認し 基準(ﾍﾞｱ)側へ押し当ててもらう",
"7. ﾘｱ側作業者に押し当ててもらっている状態で4点仮締めをする"
],
"WorkPoints": [
"ﾎﾞﾙﾄを締付ける手前まで入れる",
"架台の内側に配管穴が向いてること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:4.Y軸ﾘﾆｱｶﾞｲﾄﾞのｸﾞﾘｰｽﾆｯﾌﾟﾙ方向確認",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "Xﾋﾞｰﾑ仮取付け(REARｰ左側)",
"WorkItems": [
"2. ｽﾗｲﾀﾞｰとの位置を合わせBOLT WASHER にて仮取付けする",
"3. ①を数回揺さぶって取付け穴とﾎﾞﾙﾄのｾﾝﾀｰを合わせ基準(ﾍﾞｱ)側へ押し当てる",
"4. ①をﾘｱ側作業者が仮締め完了するまで押し当てておく",
"5. ﾘｱ側作業者の仮締め完了後､4点仮締めをする"
],
"WorkPoints": [
"取付穴とﾎﾞﾙﾄのｾﾝﾀｰ確認",
"ﾘｱ側作業者にもｾﾝﾀｰ確認してもらう",
"ﾎﾞﾙﾄを締付ける手前まで入れる",
"ﾎﾞﾙﾄのｾﾝﾀｰ確認後に締める"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"数回揺さぶる",
"基準(ﾍﾟｱ)側に押し当てる",
"仮止め:SD-EJM8EB1-057にて本締め",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Xﾋﾞｰﾑ仮取付け(REARｰ左側)",
"WorkItems": [
"◆1. ①をｽﾗｲﾄﾞさせながら載せる",
"2. ｽﾗｲﾀﾞｰとの位置を合わせBOLT WASHER にて仮取付けする",
"3. ①を数回揺さぶって取付け穴とﾎﾞﾙﾄのｾﾝﾀｰを合わせ基準(ﾍﾞｱ)側へ押し当てる",
"4. ①をﾘｱ側作業者が仮締め完了するまで押し当てておく",
"5. ﾘｱ側作業者の仮締め完了後､4点仮締めをする"
],
"WorkPoints": [
"二人作業で行う",
"ﾌﾛﾝﾄ側作業者",
"ﾘｱ側作業者",
"取付穴とﾎﾞﾙﾄのｾﾝﾀｰ確認",
"ﾘｱ側作業者にもｾﾝﾀｰ確認してもらう",
"ﾎﾞﾙﾄを締付ける手前まで入れる",
"ﾎﾞﾙﾄのｾﾝﾀｰ確認後に締める"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"数回揺さぶる",
"基準(ﾍﾟｱ)側に押し当てる",
"仮止め:SD-EJM8EB1-057にて本締め",
"FRONT",
"REAR",
"REAR"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｽﾄｯﾊﾟｰ仮取付け",
"WorkItems": [
"1. 架台右側に①をBOLT で仮取付けする",
"2. 架台左側に②をBOLT で仮取付けする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"仮止め:SD-EJM8EB1-264にて本締め",
"仮止め:SD-EJM8EB1-059にて本締め",
"FRONT"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾞﾘｰｽﾁｭｰﾌﾞ差込み",
"WorkItems": [
"1. ｸﾞﾘｰｽﾁｭｰﾌﾞを差込む"
],
"WorkPoints": [
"ｴﾙﾎﾞに4φTUBE(ｸﾘｱ)を差込む"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XY直角度計測ﾍｯﾄﾞ",
"Size": "",
"ToolOther": "FM-2413",
"WorkName": "XY直角度計測ﾍｯﾄﾞ取付け",
"WorkItems": [
"1. X軸駆動部に計測ﾍｯﾄﾞ治具を搭載する"
],
"WorkPoints": [
"この溝に引っ掛ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2413",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XY直角度計測ﾍｯﾄﾞ取付変換ﾌﾟﾚｰﾄ",
"Size": "",
"ToolOther": "FM-5788",
"WorkName": "XY直角度計測ﾍｯﾄﾞ取付け",
"WorkItems": [
"1. X軸駆動部に計測ﾍｯﾄﾞ治具を搭載する"
],
"WorkPoints": [
"この溝に引っ掛ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5788",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "CM本体組立ｽｺﾔ置台",
"Size": "",
"ToolOther": "KM-CM0396",
"WorkName": "ｽｺﾔ置き台・ｾﾗﾝｸｽ設置",
"WorkItems": [
"1. 架台に㉖を４ヶ所設置する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｾﾗﾝｸｽ",
"Size": "",
"ToolOther": "FM-0810",
"WorkName": "ｽｺﾔ置き台・ｾﾗﾝｸｽ設置",
"WorkItems": [
"2. ㉗を㉖の上に搭載する"
],
"WorkPoints": [
"設置前に㉖設置面及び㉗搭載面を清掃すること",
"㉗はバランス良く均等に載せる",
"㉗セランクスの取付方向に注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT",
"FRONT"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-0810",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XY直角度計測ﾍｯﾄﾞ",
"Size": "",
"ToolOther": "FM-2413",
"WorkName": "ｾﾗﾝｸｽ位置合わせ(FRONT)",
"WorkItems": [
"1. 計測ﾍｯﾄﾞ測定子を下ろす",
"2. ｾﾗﾝｸｽに測定子を当てる",
"3. Y軸とｾﾗﾝｸｽが平行になるようにｾﾗﾝｸｽの位置合わせを行う",
"4. 平行度が確認できたら一度ｾﾗﾝｸｽからXY軸を逃がす"
],
"WorkPoints": [
"当て量1~2mm",
"一杯に倒した所で大きいﾛｰﾚｯﾄを締め固定する",
"大きいﾛｰﾚｯﾄを緩め矢印方向に倒す",
"X軸が安定した位置でｾﾗﾝｸｽを動かして当てる",
"当てる前にﾁｪｯｶｰを0にする",
"ﾁｪｯｶｰ表示は測定子が当り方向で-符号になる",
"Y軸を動かしｾﾗﾝｸｽの両端で数値を確認する",
"測定子の当り量は1㎜~2㎜程度で行う",
"平行度:0.005mm以内にする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2413",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XY直角度計測ﾍｯﾄﾞ取付変換ﾌﾟﾚｰﾄ",
"Size": "",
"ToolOther": "FM-5788",
"WorkName": "ｾﾗﾝｸｽ位置合わせ(FRONT)",
"WorkItems": [
"1. 計測ﾍｯﾄﾞ測定子を下ろす",
"2. ｾﾗﾝｸｽに測定子を当てる",
"3. Y軸とｾﾗﾝｸｽが平行になるようにｾﾗﾝｸｽの位置合わせを行う",
"4. 平行度が確認できたら一度ｾﾗﾝｸｽからXY軸を逃がす"
],
"WorkPoints": [
"当て量1~2mm",
"一杯に倒した所で大きいﾛｰﾚｯﾄを締め固定する",
"大きいﾛｰﾚｯﾄを緩め矢印方向に倒す",
"X軸が安定した位置でｾﾗﾝｸｽを動かして当てる",
"当てる前にﾁｪｯｶｰを0にする",
"ﾁｪｯｶｰ表示は測定子が当り方向で-符号になる",
"Y軸を動かしｾﾗﾝｸｽの両端で数値を確認する",
"測定子の当り量は1㎜~2㎜程度で行う",
"平行度:0.005mm以内にする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5788",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XY直角度計測ﾍｯﾄﾞ",
"Size": "",
"ToolOther": "FM-2413",
"WorkName": "X軸直角精度測定(FRONT)",
"WorkItems": [
"1. 計測ﾍｯﾄﾞ測定子を回転させる",
"2. ｾﾗﾝｸｽに測定子を当てる",
"3. X軸直角精度を測定する"
],
"WorkPoints": [
"一杯に回転させた所で大きいﾛｰﾚｯﾄを締め固定する",
"大きいﾛｰﾚｯﾄを緩め矢印方向に回転させる",
"当てる前にﾁｪｯｶｰを0にする",
"ﾁｪｯｶｰ表示は測定子が当り方向で-符号になる",
"Y軸を少しづつ動かし当り量を0.5㎜程度にする",
"再度ﾁｪｯｶｰを0にする",
"X軸を動かし右端の数値を確認する",
"直角度:0.050mm以内",
"直角度が0.050㎜を超える場合はXﾋﾞｰﾑの取付位置調整が必要となる",
"固定子に磁性体を50mm以上近づけないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "直角度確認",
"ToolManageNo": "FM-2413",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.050㎜以内",
"Method": "XY直角度計測ﾍｯﾄﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XY直角度計測ﾍｯﾄﾞ取付変換ﾌﾟﾚｰﾄ",
"Size": "",
"ToolOther": "FM-5788",
"WorkName": "X軸直角精度測定(FRONT)",
"WorkItems": [
"1. 計測ﾍｯﾄﾞ測定子を回転させる",
"2. ｾﾗﾝｸｽに測定子を当てる",
"3. X軸直角精度を測定する"
],
"WorkPoints": [
"一杯に回転させた所で大きいﾛｰﾚｯﾄを締め固定する",
"大きいﾛｰﾚｯﾄを緩め矢印方向に回転させる",
"当てる前にﾁｪｯｶｰを0にする",
"ﾁｪｯｶｰ表示は測定子が当り方向で-符号になる",
"Y軸を少しづつ動かし当り量を0.5㎜程度にする",
"再度ﾁｪｯｶｰを0にする",
"X軸を動かし右端の数値を確認する",
"直角度:0.050mm以内",
"直角度が0.050㎜を超える場合はXﾋﾞｰﾑの取付位置調整が必要となる",
"固定子に磁性体を50mm以上近づけないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5788",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "Xﾋﾞｰﾑ位置調整(FRONT)",
"WorkItems": [
"3. 1.で緩めたﾎﾞﾙﾄを締付け再度X軸直角精度を測定する"
],
"WorkPoints": [
"ﾁｪｯｶｰ測定値が+符号の場合",
"M5のﾎﾞﾙﾄを取付ける",
"ﾁｪｯｶｰ測定値が-符号の場合",
"ﾁｪｯｶｰを0にする",
"X軸を動かし右端の数値を確認する",
"直角度:0.05mm以内",
"位置調整後は必ず調整用M5のﾎﾞﾙﾄ取外す"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XY直角度計測ﾍｯﾄﾞ",
"Size": "",
"ToolOther": "FM-2413",
"WorkName": "Xﾋﾞｰﾑ位置調整(FRONT)",
"WorkItems": [
"3. 1.で緩めたﾎﾞﾙﾄを締付け再度X軸直角精度を測定する"
],
"WorkPoints": [
"ﾁｪｯｶｰ測定値が+符号の場合",
"M5のﾎﾞﾙﾄを取付ける",
"ﾁｪｯｶｰ測定値が-符号の場合",
"ﾁｪｯｶｰを0にする",
"X軸を動かし右端の数値を確認する",
"直角度:0.05mm以内",
"位置調整後は必ず調整用M5のﾎﾞﾙﾄ取外す"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "直角度確認",
"ToolManageNo": "FM-2413",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.050㎜以内",
"Method": "XY直角度計測ﾍｯﾄﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XY直角度計測ﾍｯﾄﾞ取付変換ﾌﾟﾚｰﾄ",
"Size": "",
"ToolOther": "FM-5788",
"WorkName": "Xﾋﾞｰﾑ位置調整(FRONT)",
"WorkItems": [
"1. Xﾋﾞｰﾑ固定ﾎﾞﾙﾄを支点の1本以外緩める",
"2. 調整ﾎﾞﾙﾄを取付け位置調整する",
"3. 1.で緩めたﾎﾞﾙﾄを締付け再度X軸直角精度を測定する"
],
"WorkPoints": [
"4本共緩める",
"一旦4本共緩め､支点となる1本を締めつける",
"ﾁｪｯｶｰ測定値が-符号の場合残す",
"ﾁｪｯｶｰ測定値が+符号の場合残す",
"ﾁｪｯｶｰ測定値が+符号の場合",
"M5のﾎﾞﾙﾄを取付ける",
"ﾁｪｯｶｰ測定値が-符号の場合",
"ﾁｪｯｶｰを0にする",
"X軸を動かし右端の数値を確認する",
"直角度:0.05mm以内",
"位置調整後は必ず調整用M5のﾎﾞﾙﾄ取外す"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m",
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5788",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY直角度計測ﾍｯﾄﾞ取外し",
"WorkItems": [
"1. 駆動部に仕込んであるﾎﾞﾙﾄを緩める(4ヶ所)",
"2. X軸駆動部から計測ﾍｯﾄﾞ治具を取外す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT"
]
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XY直角度計測ﾍｯﾄﾞ",
"Size": "",
"ToolOther": "FM-2413",
"WorkName": "Xﾋﾞｰﾑ(REAR)ｾﾗﾝｸｽ平行度確認",
"WorkItems": [
"1. 計測ﾍｯﾄﾞ測定子を下ろす",
"2. ｾﾗﾝｸｽに測定子を当てる",
"3. Xﾋﾞｰﾑとｾﾗﾝｸｽ平行度を確認する",
"4. 平行度が確認できたら一度ｾﾗﾝｸｽからXﾋﾞｰﾑを逃がす"
],
"WorkPoints": [
"当て量1~2mm",
"一杯に倒した所で大きいﾛｰﾚｯﾄを締め固定する",
"大きいﾛｰﾚｯﾄを緩め矢印方向に倒す",
"X軸が安定した位置でｾﾗﾝｸｽを動かさないように慎重にXY軸を動かして測定子を当てる",
"当てる前にﾁｪｯｶｰを0にする",
"ﾁｪｯｶｰ表示は測定子が当り方向で-符号になる",
"再度ﾁｪｯｶｰを0にする",
"Y軸を動かし左端の数値を確認する",
"平行度:0.010mm以内",
"固定子に磁性体を50mm以上近づけないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "FM-2413",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.010㎜以内",
"Method": "XY直角度計測ﾍｯﾄﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XY直角度計測ﾍｯﾄﾞ取付変換ﾌﾟﾚｰﾄ",
"Size": "",
"ToolOther": "FM-5788",
"WorkName": "Xﾋﾞｰﾑ(REAR)ｾﾗﾝｸｽ平行度確認",
"WorkItems": [
"1. 計測ﾍｯﾄﾞ測定子を下ろす",
"2. ｾﾗﾝｸｽに測定子を当てる",
"3. Xﾋﾞｰﾑとｾﾗﾝｸｽ平行度を確認する",
"4. 平行度が確認できたら一度ｾﾗﾝｸｽからXﾋﾞｰﾑを逃がす"
],
"WorkPoints": [
"当て量1~2mm",
"一杯に倒した所で大きいﾛｰﾚｯﾄを締め固定する",
"大きいﾛｰﾚｯﾄを緩め矢印方向に倒す",
"X軸が安定した位置でｾﾗﾝｸｽを動かさないように慎重にXY軸を動かして測定子を当てる",
"当てる前にﾁｪｯｶｰを0にする",
"ﾁｪｯｶｰ表示は測定子が当り方向で-符号になる",
"再度ﾁｪｯｶｰを0にする",
"Y軸を動かし左端の数値を確認する",
"平行度:0.010mm以内",
"固定子に磁性体を50mm以上近づけないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5788",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XY直角度計測ﾍｯﾄﾞ",
"Size": "",
"ToolOther": "FM-2413",
"WorkName": "X軸直角精度測定(REAR)",
"WorkItems": [
"1. 計測ﾍｯﾄﾞ測定子を回転させる",
"2. ｾﾗﾝｸｽに測定子を当てる",
"3. X軸直角精度を測定する"
],
"WorkPoints": [
"一杯に回転させた所で大きいﾛｰﾚｯﾄを締め固定する",
"大きいﾛｰﾚｯﾄを緩め矢印方向に回転させる",
"当てる前にﾁｪｯｶｰを0にする",
"ﾁｪｯｶｰ表示は測定子が当り方向で-符号になる",
"Y軸を少しづつ動かし当り量を0.5㎜程度にする",
"再度ﾁｪｯｶｰを0にする",
"X軸を動かし右端の数値を確認する",
"直角度:0.050mm以内",
"直角度が0.050㎜を超える場合はXﾋﾞｰﾑの取付位置調整が必要となる",
"固定子に磁性体を50mm以上近づけないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT"
]
} | {
"QualityItem": "直角度確認",
"ToolManageNo": "FM-2413",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.050㎜以内",
"Method": "XY直角度計測ﾍｯﾄﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XY直角度計測ﾍｯﾄﾞ取付変換ﾌﾟﾚｰﾄ",
"Size": "",
"ToolOther": "FM-5788",
"WorkName": "X軸直角精度測定(REAR)",
"WorkItems": [
"1. 計測ﾍｯﾄﾞ測定子を回転させる",
"2. ｾﾗﾝｸｽに測定子を当てる",
"3. X軸直角精度を測定する"
],
"WorkPoints": [
"一杯に回転させた所で大きいﾛｰﾚｯﾄを締め固定する",
"大きいﾛｰﾚｯﾄを緩め矢印方向に回転させる",
"当てる前にﾁｪｯｶｰを0にする",
"ﾁｪｯｶｰ表示は測定子が当り方向で-符号になる",
"Y軸を少しづつ動かし当り量を0.5㎜程度にする",
"再度ﾁｪｯｶｰを0にする",
"X軸を動かし右端の数値を確認する",
"直角度:0.050mm以内",
"直角度が0.050㎜を超える場合はXﾋﾞｰﾑの取付位置調整が必要となる",
"固定子に磁性体を50mm以上近づけないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5788",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "Xﾋﾞｰﾑ位置調整(REAR)",
"WorkItems": [],
"WorkPoints": [
"ﾁｪｯｶｰ測定値が-符号の場合",
"ﾁｪｯｶｰを0にする",
"X軸を動かし右端の数値を確認する",
"直角度:0.05mm以内",
"位置調整後は必ず調整用M5のﾎﾞﾙﾄ取外す",
"固定子に磁性体を50mm以上近づけないこと"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XY直角度計測ﾍｯﾄﾞ",
"Size": "",
"ToolOther": "FM-2413",
"WorkName": "Xﾋﾞｰﾑ位置調整(REAR)",
"WorkItems": [],
"WorkPoints": [
"ﾁｪｯｶｰ測定値が-符号の場合",
"ﾁｪｯｶｰを0にする",
"X軸を動かし右端の数値を確認する",
"直角度:0.05mm以内",
"位置調整後は必ず調整用M5のﾎﾞﾙﾄ取外す",
"固定子に磁性体を50mm以上近づけないこと"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "直角度確認",
"ToolManageNo": "FM-2413",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.050㎜以内",
"Method": "XY直角度計測ﾍｯﾄﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XY直角度計測ﾍｯﾄﾞ取付変換ﾌﾟﾚｰﾄ",
"Size": "",
"ToolOther": "FM-5788",
"WorkName": "Xﾋﾞｰﾑ位置調整(REAR)",
"WorkItems": [],
"WorkPoints": [
"ﾁｪｯｶｰ測定値が-符号の場合",
"ﾁｪｯｶｰを0にする",
"X軸を動かし右端の数値を確認する",
"直角度:0.05mm以内",
"位置調整後は必ず調整用M5のﾎﾞﾙﾄ取外す",
"固定子に磁性体を50mm以上近づけないこと"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5788",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾﾗﾝｸｽ・ｽｺﾔ置き台・XYﾁｪｯｶｰ収納",
"WorkItems": [
"1. ｾﾗﾝｸｽを収納する",
"2. ｽｺﾔ置き台を収納する",
"3. XYﾁｪｯｶｰをｼｬｯﾄﾀﾞｳﾝし片付ける"
],
"WorkPoints": [
"ｺﾝﾄﾛｰﾙBOXの電源がOFFになっているか確認する",
"ﾊﾟｿｺﾝをｼｬｯﾄﾀﾞｳﾝする",
"ｹｰﾌﾞﾙを収納する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT",
"FRONT"
]
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "Xﾋﾞｰﾑ本取付け(FRONTｰ左側)",
"WorkItems": [
"1. Xﾋﾞｰﾑ取付けﾎﾞﾙﾄの本締めを行う(8ヵ所)"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT",
"FRONT"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "Xﾋﾞｰﾑ本取付け(REARｰ左側)",
"WorkItems": [
"1. Xﾋﾞｰﾑ取付けﾎﾞﾙﾄの本締めを行う(8ヵ所)"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT",
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "他軸干渉ｾﾝｻ調整治具",
"Size": "",
"ToolOther": "FM-3458",
"WorkName": "Y軸干渉PHｾﾝｻ用ﾄﾞｸﾞ取付・調整",
"WorkItems": [
"1. DOG をBOLT WASHER で仮取付する",
"■2. 干渉PHセンサに㉗を接続し、㉘を挟み込んだ状態でONするようDOG位置を調整する"
],
"WorkPoints": [
"干渉PHｾﾝｻ",
"ﾄﾞｸﾞが干渉PHｾﾝｻに入り込んだ時､ｾﾝｻの開口部が均等になる様に調整する",
"隙間1mm時ｾﾝｻがONすること",
"A矢視"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "WEPJ-G002-C02",
"InspectionItems": [
"検査表DOG :17.Y軸干渉PH調整"
],
"WorkTypes": [],
"Words": [
"A矢視",
"FRONT",
"WEPJ-G002-C02"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-3458",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:1㎜",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2375",
"WorkName": "Y軸干渉PHｾﾝｻ用ﾄﾞｸﾞ取付・調整",
"WorkItems": [
"1. DOG をBOLT WASHER で仮取付する",
"■2. 干渉PHセンサに㉗を接続し、㉘を挟み込んだ状態でONするようDOG位置を調整する"
],
"WorkPoints": [
"干渉PHｾﾝｻ",
"A矢視"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"A矢視",
"FRONT",
"検査表DOG :17.Y軸干渉PH調整",
"■安全作業",
"WEPJ-G002-C02"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2375",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作している事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "Y軸干渉PHｾﾝｻ用ﾄﾞｸﾞ取付・調整",
"WorkItems": [
"1. DOG をBOLT WASHER で仮取付する",
"■2. 干渉PHセンサに㉗を接続し、㉘を挟み込んだ状態でONするようDOG位置を調整する"
],
"WorkPoints": [
"干渉PHｾﾝｻ",
"A矢視"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"A矢視",
"FRONT",
"検査表DOG :17.Y軸干渉PH調整",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸干渉PHｾﾝｻ用ﾄﾞｸﾞ取付け・調整",
"WorkItems": [
"1. DOG をBOLT WASHER で仮取付する",
"■2. 干渉PHセンサに㉗を接続し、㉘を挟み込んだ状態でONするようDOG位置を調整する"
],
"WorkPoints": [
"干渉PHｾﾝｻ",
"ﾄﾞｸﾞが干渉PHｾﾝｻに入り込んだ時､ｾﾝｻの開口部が均等になる様に調整する",
"隙間1mm時ｾﾝｻがONすること",
"A矢視"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"A矢視",
"FRONT",
"検査表DOG :17.Y軸干渉PH調整",
"WEPJ-G002-C02"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り隙間調整出来ている事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸干渉PHｾﾝｻ用ﾄﾞｸﾞ取付け・調整",
"WorkItems": [
"1. DOG をBOLT WASHER で仮取付する",
"■2. 干渉PHセンサに㉗を接続し、㉘を挟み込んだ状態でONするようDOG位置を調整する"
],
"WorkPoints": [
"干渉PHｾﾝｻ",
"ﾄﾞｸﾞが干渉PHｾﾝｻに入り込んだ時､ｾﾝｻの開口部が均等になる様に調整する",
"隙間1mm時ｾﾝｻがONすること",
"A矢視"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"A矢視",
"FRONT",
"検査表DOG :17.Y軸干渉PH調整",
"WEPJ-G002-C02"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り隙間調整出来ている事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2375",
"WorkName": "Y軸干渉PHｾﾝｻ用ﾄﾞｸﾞ取付け・調整",
"WorkItems": [
"1. DOG をBOLT WASHER で仮取付する",
"■2. 干渉PHセンサに㉗を接続し、㉘を挟み込んだ状態でONするようDOG位置を調整する"
],
"WorkPoints": [
"干渉PHｾﾝｻ",
"A矢視"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"A矢視",
"FRONT",
"検査表DOG :17.Y軸干渉PH調整",
"■安全作業",
"WEPJ-G002-C02"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-2375",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作している事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰｹｰﾌﾞﾙ",
"Size": "",
"ToolOther": "FM-4301",
"WorkName": "Y軸干渉PHｾﾝｻ用ﾄﾞｸﾞ取付け・調整",
"WorkItems": [
"1. DOG をBOLT WASHER で仮取付する",
"■2. 干渉PHセンサに㉗を接続し、㉘を挟み込んだ状態でONするようDOG位置を調整する"
],
"WorkPoints": [
"干渉PHｾﾝｻ",
"ﾄﾞｸﾞが干渉PHｾﾝｻに入り込んだ時､ｾﾝｻの開口部が均等になる様に調整する",
"隙間1mm時ｾﾝｻがONすること",
"A矢視"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"A矢視",
"FRONT",
"検査表DOG :17.Y軸干渉PH調整",
"WEPJ-G002-C02"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4301",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作している事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "Y軸干渉PHｾﾝｻ用ﾄﾞｸﾞ取付け・調整",
"WorkItems": [
"1. DOG をBOLT WASHER で仮取付する",
"■2. 干渉PHセンサに㉗を接続し、㉘を挟み込んだ状態でONするようDOG位置を調整する"
],
"WorkPoints": [
"干渉PHｾﾝｻ",
"A矢視"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"A矢視",
"FRONT",
"検査表DOG :17.Y軸干渉PH調整",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "",
"WorkName": "Yﾌﾚｰﾑ(1)仮取付け(左側)及び安全対策PLATE取付け",
"WorkItems": [
"2. 架台への取付面及び固定子取付面に砥石をかけ、㉗で洗浄する"
],
"WorkPoints": [
"上面",
"底面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ等無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "Yﾌﾚｰﾑ(1)仮取付け(左側)及び安全対策PLATE取付け",
"WorkItems": [
"1. ﾌﾛﾝﾄ側のXﾋﾞｰﾑをﾘｱ側まで移動する",
"3. Y-FRAME(1) にCOVER をBOLT で取付ける",
"◆4. Y-FRAME(1) をﾋﾟﾝに嵌め込み､BOLT BOLT で仮取付する"
],
"WorkPoints": [
"搭載時二人作業",
"F側から見て右がｼﾘｱﾙNoの若番"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Yﾌﾚｰﾑ(1)仮取付け(左側)及び安全対策PLATE取付け",
"WorkItems": [
"1. ﾌﾛﾝﾄ側のXﾋﾞｰﾑをﾘｱ側まで移動する",
"2. 架台への取付面及び固定子取付面に砥石をかけ、㉗で洗浄する",
"3. Y-FRAME(1) にCOVER をBOLT で取付ける",
"◆4. Y-FRAME(1) をﾋﾟﾝに嵌め込み､BOLT BOLT で仮取付する"
],
"WorkPoints": [
"上面",
"底面",
"搭載時二人作業",
"F側から見て右がｼﾘｱﾙNoの若番"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
": 架台への取付面",
": 固定子取付面",
"仮止め:SD-EJM8EB1-060にて本締め",
"FRONT"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "ｽﾄｯﾊﾟｰ及びYﾌﾚｰﾑ(1)本取付け(左側)",
"WorkItems": [
"2. 架台に取付ける3本を締め付ける",
"1. ｽﾄｯﾊﾟｰにBOLT を仮入れする",
"3. Yﾌﾚｰﾑに取付ける5本を締付ける"
],
"WorkPoints": [
"Yﾌﾚｰﾑをｽﾄｯﾊﾟｰに押し当ててから上部を押さえ付けた状態で締付ける"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｽﾄｯﾊﾟｰ及びYﾌﾚｰﾑ(1)本取付け(左側)",
"WorkItems": [],
"WorkPoints": [
"ｽﾄｯﾊﾟｰを下側に押さえ付けた状態で締付ける"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "",
"WorkName": "Yﾌﾚｰﾑ(2)取付け(左側)及び安全対策PLATE取付け",
"WorkItems": [
"2. 架台への取付面及び固定子取付面に砥石をかけ、㉗で洗浄する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ等無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "Yﾌﾚｰﾑ(2)取付け(左側)及び安全対策PLATE取付け",
"WorkItems": [
"1. ﾌﾛﾝﾄ側のXﾋﾞｰﾑをﾌﾛﾝﾄ側まで移動する",
"3. Y-FRAME(2) にCOVER をBOLT で取付ける",
"◆4. Y-FRAME(2) をﾋﾟﾝに嵌め込み､BOLT BOLT で取付ける"
],
"WorkPoints": [
"ﾘｱ側作業の完了を確認すること",
"上面",
"底面",
"搭載時二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "Yﾌﾚｰﾑ(2)取付け(左側)及び安全対策PLATE取付け",
"WorkItems": [
"1. ﾌﾛﾝﾄ側のXﾋﾞｰﾑをﾌﾛﾝﾄ側まで移動する",
"3. Y-FRAME(2) にCOVER をBOLT で取付ける",
"◆4. Y-FRAME(2) をﾋﾟﾝに嵌め込み､BOLT BOLT で取付ける"
],
"WorkPoints": [
"ﾘｱ側作業の完了を確認すること",
"上面",
"底面",
"搭載時二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Yﾌﾚｰﾑ(2)取付け(左側)及び安全対策PLATE取付け",
"WorkItems": [
"1. ﾌﾛﾝﾄ側のXﾋﾞｰﾑをﾌﾛﾝﾄ側まで移動する",
"2. 架台への取付面及び固定子取付面に砥石をかけ、㉗で洗浄する",
"3. Y-FRAME(2) にCOVER をBOLT で取付ける",
"◆4. Y-FRAME(2) をﾋﾟﾝに嵌め込み､BOLT BOLT で取付ける"
],
"WorkPoints": [
"ﾘｱ側作業の完了を確認すること",
"上面",
"底面",
"搭載時二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT",
": 架台への取付面",
": 固定子取付面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "",
"WorkName": "Yﾌﾚｰﾑ(3)仮取付け(左側)及び安全対策PLATE取付け",
"WorkItems": [
"2. 架台への取付面及び固定子取付面に砥石をかけ、㉗で洗浄する"
],
"WorkPoints": [
"仮止め:SD-EJM8EB1-062にて本締め"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
": 架台への取付面",
": 固定子取付面"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ等無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "Yﾌﾚｰﾑ(3)仮取付け(左側)及び安全対策PLATE取付け",
"WorkItems": [
"4. Y-FRAME(3) をﾋﾟﾝに嵌め込み､BOLT BOLT で仮取付けする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Yﾌﾚｰﾑ(3)仮取付け(左側)及び安全対策PLATE取付け",
"WorkItems": [
"1. ﾘｱ側のXﾋﾞｰﾑをﾌﾛﾝﾄ側まで移動する",
"2. 架台への取付面及び固定子取付面に砥石をかけ、㉗で洗浄する",
"3. Y-FRAME(3) にCOVER をBOLT で取付ける",
"4. Y-FRAME(3) をﾋﾟﾝに嵌め込み､BOLT BOLT で仮取付けする"
],
"WorkPoints": [
"ﾘｱ側作業の完了を確認すること",
"上面",
"底面",
"仮止め:SD-EJM8EB1-062にて本締め"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT",
": 架台への取付面",
": 固定子取付面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "ｽﾄｯﾊﾟｰ(REAR側)及びYﾌﾚｰﾑ(3)本取付け(左側)",
"WorkItems": [
"2. 架台に取付ける3本を締め付ける",
"3. Yﾌﾚｰﾑに取付ける5本を締め付ける"
],
"WorkPoints": [
"Yﾌﾚｰﾑをｽﾄｯﾊﾟｰに押し当ててから上部を押さえ付けた状態で締付ける"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｽﾄｯﾊﾟｰ(REAR側)及びYﾌﾚｰﾑ(3)本取付け(左側)",
"WorkItems": [
"4. Yﾌﾚｰﾑを本取付けする"
],
"WorkPoints": [
"ｽﾄｯﾊﾟｰを下側に押さえ付けた状態で締付ける"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "操作ﾊﾟﾈﾙｹｰﾌﾞﾙ固定(FRONT)",
"WorkItems": [
"1. ｽﾄｯﾊﾟｰにｹｰﾌﾞﾙを固定する"
],
"WorkPoints": [
"ﾌｪﾗｲﾄｺｱを共締めしないこと",
"配線束の厚みがﾌｪﾗｲﾄｺｱより膨らまないように処理すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"3A03",
"USBA03",
"S311P1",
"G103P",
"FSW1R",
"1A03",
"B211P",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"S201"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸可動子(FRONTｰ左側)取付け",
"WorkItems": [
"■1. MOTOR の型式､ｼﾘｱﾙNo.を確認する",
"2. Yﾌﾚｰﾑに治具を置いてMOTOR を置く",
"3. MOTOR をX軸にBOLT WASHER で固定する",
"4. ㉖を取外す"
],
"WorkPoints": [
"MOTOR の配線が作業者側なる様にｾｯﾄすること",
"ﾈｼﾞ穴を合わせ､MOTOR をX軸のﾋﾟﾝに押し込み締結のこと"
],
"Tolks": [
"締付ﾄﾙｸ 11.2N･m"
],
"InspectionNo": "WEPJ-G002-C02",
"InspectionItems": [
"検査表MOTOR :5.Y軸ﾓｰﾀのｼﾘｱﾙNo.確認"
],
"WorkTypes": [],
"Words": [
"作業者",
"配線",
"左側面",
"Yﾌﾚｰﾑ",
"ﾌﾛﾝﾄ",
"左側面",
"WEPJ-G002-C02"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y可動子取付治具",
"Size": "",
"ToolOther": "FM-4627",
"WorkName": "Y軸可動子(FRONTｰ左側)取付け",
"WorkItems": [
"■1. MOTOR の型式､ｼﾘｱﾙNo.を確認する",
"2. Yﾌﾚｰﾑに治具を置いてMOTOR を置く",
"3. MOTOR をX軸にBOLT WASHER で固定する",
"4. ㉖を取外す"
],
"WorkPoints": [
"MOTOR の配線が作業者側なる様にｾｯﾄすること",
"ﾈｼﾞ穴を合わせ､MOTOR をX軸のﾋﾟﾝに押し込み締結のこと"
],
"Tolks": [
"締付ﾄﾙｸ 11.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"作業者",
"配線",
"左側面",
"Yﾌﾚｰﾑ",
"ﾌﾛﾝﾄ",
"検査表MOTOR :5.Y軸ﾓｰﾀのｼﾘｱﾙNo.確認",
"■安全作業",
"左側面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4627",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.2N･m",
"WorkName": "Y軸可動子(FRONTｰ左側)取付け",
"WorkItems": [
"3. MOTOR をX軸にBOLT WASHER で固定する",
"4. ㉖を取外す"
],
"WorkPoints": [
"ﾈｼﾞ穴を合わせ､MOTOR をX軸のﾋﾟﾝに押し込み締結のこと"
],
"Tolks": [
"締付ﾄﾙｸ 11.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"左側面",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸可動子(FRONTｰ右側)取付け",
"WorkItems": [
"■1. MOTOR の型式､ｼﾘｱﾙNo.を確認する",
"2. Yﾌﾚｰﾑに治具を置いてMOTOR を置く",
"3. MOTOR をX軸にBOLT WASHER で固定する",
"4. ㉖を取外す"
],
"WorkPoints": [
"MOTOR の配線が作業者側なる様にｾｯﾄすること",
"ﾈｼﾞ穴を合わせ､MOTOR をX軸のﾋﾟﾝに押し込み締結のこと"
],
"Tolks": [
"締付ﾄﾙｸ 11.2N･m"
],
"InspectionNo": "WEPJ-G002-C02",
"InspectionItems": [
"検査表MOTOR :5.Y軸ﾓｰﾀのｼﾘｱﾙNo.確認"
],
"WorkTypes": [],
"Words": [
"右側面",
"ﾌﾛﾝﾄ",
"作業者",
"配線",
"右側面",
"Yﾌﾚｰﾑ",
"WEPJ-G002-C02"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y可動子取付治具",
"Size": "",
"ToolOther": "FM-4627",
"WorkName": "Y軸可動子(FRONTｰ右側)取付け",
"WorkItems": [
"■1. MOTOR の型式､ｼﾘｱﾙNo.を確認する",
"2. Yﾌﾚｰﾑに治具を置いてMOTOR を置く",
"3. MOTOR をX軸にBOLT WASHER で固定する",
"4. ㉖を取外す",
"■1. MOTOR の型式､ｼﾘｱﾙNo.を確認する",
"2. Yﾌﾚｰﾑに治具を置いてMOTOR を置く",
"3. MOTOR をX軸にBOLT WASHER で固定する",
"4. ㉖を取外す"
],
"WorkPoints": [
"MOTOR の配線が作業者側なる様にｾｯﾄすること",
"ﾈｼﾞ穴を合わせ､MOTOR をX軸のﾋﾟﾝに押し込み締結のこと",
"MOTOR の配線が作業者側なる様にｾｯﾄすること",
"ﾈｼﾞ穴を合わせ､MOTOR をX軸のﾋﾟﾝに押し込み締結のこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"検査表MOTOR :5.Y軸ﾓｰﾀのｼﾘｱﾙNo.確認",
"■安全作業",
"ﾌﾛﾝﾄ",
"検査表MOTOR :5.Y軸ﾓｰﾀのｼﾘｱﾙNo.確認"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4627",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "11.2N･m",
"WorkName": "Y軸可動子(FRONTｰ右側)取付け",
"WorkItems": [
"■1. MOTOR の型式､ｼﾘｱﾙNo.を確認する",
"2. Yﾌﾚｰﾑに治具を置いてMOTOR を置く",
"3. MOTOR をX軸にBOLT WASHER で固定する",
"4. ㉖を取外す"
],
"WorkPoints": [
"MOTOR の配線が作業者側なる様にｾｯﾄすること",
"ﾈｼﾞ穴を合わせ､MOTOR をX軸のﾋﾟﾝに押し込み締結のこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌﾛﾝﾄ",
"検査表MOTOR :5.Y軸ﾓｰﾀのｼﾘｱﾙNo.確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸固定子取付け①",
"WorkItems": [
"◆1. MOTOR の固定子を固定子確認ﾏｯﾄ(2枚準備)を活用し表示通りにｾｯﾄする",
"◆2. 固定子の傷､打痕を確認する",
"■◆3. MOTOR のｼﾘｱﾙNo及び型式確認"
],
"WorkPoints": [
"固定子の傷､打痕確認は1枚毎に保護ｶﾊﾞｰを外し確認のことまとめて保護ｶﾊﾞｰ外すと固定子同士くっつく恐れ有保護ｶﾊﾞｰ取付けﾋﾞｽは確認ﾏｯﾄ表示通りに締め付けのこと",
"極性を間違えないよう､注意すること"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C02",
"InspectionItems": [
"検査表MOTOR :5.Y軸ﾓｰﾀｼﾘｱﾙNo.確認(Y軸ﾓｰﾀ型式確認)"
],
"WorkTypes": [],
"Words": [
"固定子",
"固定子",
"固定子",
"固定子",
"WEPJ-G002-C02"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "固定子確認ﾏｯﾄ",
"Size": "",
"ToolOther": "FM-3304",
"WorkName": "Y軸固定子取付け①",
"WorkItems": [
"◆1. MOTOR の固定子を固定子確認ﾏｯﾄ(2枚準備)を活用し表示通りにｾｯﾄする",
"◆2. 固定子の傷､打痕を確認する",
"■◆3. MOTOR のｼﾘｱﾙNo及び型式確認",
"◆1. MOTOR の固定子を固定子確認ﾏｯﾄ(2枚準備)を活用し表示通りにｾｯﾄする",
"◆2. 固定子の傷､打痕を確認する",
"■◆3. MOTOR のｼﾘｱﾙNo及び型式確認"
],
"WorkPoints": [
"固定子の傷､打痕確認は1枚毎に保護ｶﾊﾞｰを外し確認のことまとめて保護ｶﾊﾞｰ外すと固定子同士くっつく恐れ有保護ｶﾊﾞｰ取付けﾋﾞｽは確認ﾏｯﾄ表示通りに締め付けのこと",
"極性を間違えないよう､注意すること",
"固定子の傷､打痕確認は1枚毎に保護ｶﾊﾞｰを外し確認のことまとめて保護ｶﾊﾞｰ外すと固定子同士くっつく恐れ有保護ｶﾊﾞｰ取付けﾋﾞｽは確認ﾏｯﾄ表示通りに締め付けのこと",
"極性を間違えないよう､注意すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業",
"◆作業者安全作業",
"固定子",
"固定子",
"固定子",
"固定子",
"検査表MOTOR :5.Y軸ﾓｰﾀｼﾘｱﾙNo.確認(Y軸ﾓｰﾀ型式確認)",
"固定子",
"固定子",
"固定子",
"固定子",
"検査表MOTOR :5.Y軸ﾓｰﾀｼﾘｱﾙNo.確認(Y軸ﾓｰﾀ型式確認)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3304",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "Y軸固定子取付け②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C02",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "固定子締付用ﾋﾞｯﾄ",
"Size": "3㎜",
"ToolOther": "FM-4575",
"WorkName": "Y軸固定子取付け②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C02",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WEPJ-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4575",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸用ﾛﾝｸﾞﾋﾞｯﾄ",
"Size": "3㎜",
"ToolOther": "FM-4500",
"WorkName": "Y軸固定子取付け②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WEPJ-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4500",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "固定子取付治具(幅60/高75)",
"Size": "",
"ToolOther": "FM-3033",
"WorkName": "Y軸固定子取付け②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WEPJ-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3033",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾆｱﾓｰﾀGAP確認治具0.2",
"Size": "",
"ToolOther": "FM-3188",
"WorkName": "Y軸固定子取付け③",
"WorkItems": [
"◆2. 左右の可動子と固定子の隙間を確認"
],
"WorkPoints": [
"通り:0.2mm 止まり:0.8mm"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C02",
"InspectionItems": [
"検査表①:7.ﾘﾆｱﾓｰﾀGAPの確認"
],
"WorkTypes": [],
"Words": [
"上側固定子",
"下側固定子",
"可動子",
"隙間確認",
"GAP確認治具t=0.2､0.8",
"◆作業者安全作業",
"WEPJ-G002-C02"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-3188",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "通り:0.2㎜止まり:0.8㎜",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾆｱﾓｰﾀGAP確認治具0.8",
"Size": "",
"ToolOther": "FM-3045",
"WorkName": "Y軸固定子取付け③",
"WorkItems": [
"◆2. 左右の可動子と固定子の隙間を確認"
],
"WorkPoints": [
"通り:0.2mm 止まり:0.8mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"上側固定子",
"下側固定子",
"可動子",
"隙間確認",
"GAP確認治具t=0.2､0.8",
"検査表①:7.ﾘﾆｱﾓｰﾀGAPの確認",
"◆作業者安全作業",
"WEPJ-G002-C02"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-3045",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "通り:0.2㎜止まり:0.8㎜",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C02",
"Other": "ﾏｸﾞﾈｯﾄ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "Y軸固定子ｶﾊﾞｰ取付け(FRONT)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "保護ｶﾊﾞｰ",
"Size": "",
"ToolOther": "FM-3050",
"WorkName": "Y軸固定子ｶﾊﾞｰ取付け(FRONT)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3050",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾒｲﾝｴｱｰﾕﾆｯﾄ取付け",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾌｧﾝｶﾞｰﾄﾞ取付け",
"WorkItems": [
"1. FAN-GUARD をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります",
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾞﾛﾒｯﾄ取付け",
"WorkItems": [
"1. ①を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "真空ﾎﾟﾝﾌﾟ冷却用ﾌｧﾝ・ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"2. ②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｹｰﾌﾞﾙがある方が上側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FRONT",
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "真空ﾎﾟﾝﾌﾟ冷却用ﾌｧﾝ・ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. BRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "架台銘板貼付けｼﾞｸﾞ13",
"Size": "",
"ToolOther": "FM-5938",
"WorkName": "真空ﾎﾟﾝﾌﾟ冷却用ﾌｧﾝ・ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"3. 治具 ㉛を使用しLABEL を架台に貼付ける"
],
"WorkPoints": [
"端面を合わせる",
"内側に取付ける",
"貼付ける前に清掃して貼付けること"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-5938",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ投入",
"WorkItems": [
"◆1. ①を架台に投入する"
],
"WorkPoints": [
"矢印方向に回転させながら投入していく",
"ﾌﾛﾝﾄ側にACｹｰﾌﾞﾙを送りながら投入していく",
"ｹｰﾌﾞﾙ挟み込み注意!!"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ取付け①",
"WorkItems": [
"1. 左側ﾕﾆｯﾄの固定を外す",
"2. 安全ｼｰｹﾝｻｰを治具から外す",
"3. 左側ﾕﾆｯﾄ押さえと上側の治具を外す",
"4. 電源部の治具を外す",
"5. .外し終わった治具を返却"
],
"WorkPoints": [
"ﾉﾌﾞを外す",
"ﾌﾞﾗｹｯﾄをﾅｯﾄから外す",
"差込む",
"電源をﾉﾌﾞで固定する",
"ﾉﾌﾞ6ヶ含"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"上側の治具をｽﾗｲﾄﾞして外す",
"ﾉﾌﾞを外す",
"ﾉﾌﾞを外す",
"安全ｼｰｹﾝｻｰを外す"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ取付け②",
"WorkItems": [
"1. ①を架台にBOLT WASHER で取付ける",
"2. CABLE-SUPPORT を架台に取付ける"
],
"WorkPoints": [
"通し穴横向き",
"通し穴縦向き",
"取付け方向",
"全8箇所"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"○･･･",
"○･･･",
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "架台下冷却ﾌｧﾝ・ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. ①FAN-GUARD をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "架台銘板貼付けｼﾞｸﾞ12",
"Size": "",
"ToolOther": "FM-5937",
"WorkName": "架台下冷却ﾌｧﾝ・ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"2. 治具㉙を使用しLABEL を架台に貼付ける",
"3. CABLE-SUPPORT を架台に取付ける"
],
"WorkPoints": [
"通し穴横向き",
"ﾌｧﾝから出てるｹｰﾌﾞﾙをﾘｱ側方向にする",
"貼付ける前に清掃して貼付けること",
"端面を合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります",
"REAR"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-5937",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "架台銘板貼付けｼﾞｸﾞ7",
"Size": "",
"ToolOther": "FM-5932",
"WorkName": "FGｼｰﾙ貼付け",
"WorkItems": [
"1. LABEL を架台に貼付ける",
"2. LABEL を架台に貼付ける"
],
"WorkPoints": [
"貼付ける前に清掃し向きに注意して貼付けること",
"架台下面",
"貼付ける前に清掃し向きに注意して貼付けること",
"ﾏｽｷﾝｸﾞの領域の右上に貼付ける",
"ﾏｽｷﾝｸﾞの領域の左下に貼付ける",
"ﾏｽｷﾝｸﾞの領域の左下に貼付ける",
"ﾏｽｷﾝｸﾞの領域の右上に貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-5932",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "架台銘板貼付けｼﾞｸﾞ8",
"Size": "",
"ToolOther": "FM-5933",
"WorkName": "FGｼｰﾙ貼付け",
"WorkItems": [
"1. LABEL を架台に貼付ける",
"2. LABEL を架台に貼付ける"
],
"WorkPoints": [
"貼付ける前に清掃し向きに注意して貼付けること",
"架台下面",
"貼付ける前に清掃し向きに注意して貼付けること",
"ﾏｽｷﾝｸﾞの領域の右上に貼付ける",
"ﾏｽｷﾝｸﾞの領域の左下に貼付ける",
"ﾏｽｷﾝｸﾞの領域の左下に貼付ける",
"ﾏｽｷﾝｸﾞの領域の右上に貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-5933",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "架台銘板貼付けｼﾞｸﾞ14",
"Size": "",
"ToolOther": "FM-5939",
"WorkName": "FGｼｰﾙ貼付け",
"WorkItems": [
"1. LABEL を架台に貼付ける",
"2. LABEL を架台に貼付ける"
],
"WorkPoints": [
"貼付ける前に清掃し向きに注意して貼付けること",
"架台下面",
"貼付ける前に清掃し向きに注意して貼付けること",
"ﾏｽｷﾝｸﾞの領域の右上に貼付ける",
"ﾏｽｷﾝｸﾞの領域の左下に貼付ける",
"ﾏｽｷﾝｸﾞの領域の左下に貼付ける",
"ﾏｽｷﾝｸﾞの領域の右上に貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-5939",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "架台銘板貼付けｼﾞｸﾞ11",
"Size": "",
"ToolOther": "FM-5936",
"WorkName": "感電注意ｼｰﾙ貼付け",
"WorkItems": [
"1. 治具㉗を使用しLABEL を架台に貼付ける"
],
"WorkPoints": [
"貼付ける前に清掃して貼付けること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-5936",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "架台銘板貼付けｼﾞｸﾞ16",
"Size": "",
"ToolOther": "FM-6095",
"WorkName": "感電注意ｼｰﾙ貼付け",
"WorkItems": [
"2. 治具㉘を使用しLABEL を架台に貼付ける"
],
"WorkPoints": [
"貼付ける前に清掃して貼付けること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-6095",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "架台銘板貼付けｼﾞｸﾞ10",
"Size": "",
"ToolOther": "FM-5935",
"WorkName": "感電注意ｼｰﾙ貼付け",
"WorkItems": [
"3. 治具㉙を使用しLABEL を架台に貼付ける"
],
"WorkPoints": [
"端面を合わせる",
"干渉するﾏｳﾝﾄは1度外した後､元に戻すこと",
"貼付ける前に清掃して貼付けること",
"端面を合わせる",
"端面を合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-5935",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "架台銘板貼付けｼﾞｸﾞ2",
"Size": "",
"ToolOther": "FM-5927",
"WorkName": "ｶｯﾀｰﾊﾞﾙﾌﾞ・台車中継ｼｰﾙ貼付け",
"WorkItems": [
"1. 治具㉗を使用しLABEL を架台に貼付ける"
],
"WorkPoints": [
"貼付ける前に清掃して貼付けること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"削除"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-5927",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "架台銘板貼付けｼﾞｸﾞ4",
"Size": "",
"ToolOther": "FM-5929",
"WorkName": "ｶｯﾀｰﾊﾞﾙﾌﾞ・台車中継ｼｰﾙ貼付け",
"WorkItems": [
"2. 治具㉘を使用しLABEL を架台に貼付ける"
],
"WorkPoints": [
"貼付ける前に清掃して貼付けること",
"端面を合わせる",
"端面を合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-5929",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. BRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄｹｰﾌﾞﾙ引き回し",
"WorkItems": [
"1. ﾌﾛﾝﾄ側から送られたﾄﾞﾗｲﾊﾞｰ線を引き回す",
"2. ﾄﾞﾗｲﾊﾞｰ線を引き回しｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"DC電源ｹｰﾌﾞﾙの上を引き回す",
"190mm寸法",
"190mm寸法",
"170mm寸法",
"寸法はｺﾈｸﾀの根元より計測",
"FANｹｰﾌﾞﾙは結束しない",
"左側から固定していく",
"DC電源ｹｰﾌﾞﾙは2個所のみ固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ (100mm)",
"ｲﾝｼｭﾛｯｸ (100mm)",
"XAK504 他",
"XAK508 他",
"XAK503 他",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"ｲﾝｼｭﾛｯｸ (150mm)",
"ｲﾝｼｭﾛｯｸ (150mm)",
"REAR"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ｺﾈｸﾀ中継ﾌﾞﾗｹｯﾄ取付け【OP:ﾄﾚｲ仕様】",
"WorkItems": [
"2. 電源ｹｰﾌﾞﾙを中継ﾌﾞﾗｹｯﾄに接続",
"■3. FG端子を②で固定する",
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [
"TRAY.PR",
"FGTR1"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ｺﾈｸﾀ中継ﾌﾞﾗｹｯﾄ・電源ｹｰﾌﾞﾙ・FG線取付け【OP:ﾄﾚｲ仕様】",
"WorkItems": [
"2. 電源ｹｰﾌﾞﾙを中継ﾌﾞﾗｹｯﾄに接続",
"■3. FG端子を②で固定する",
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [
"TRAY.PR",
"FGTR1"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ｺﾈｸﾀ中継ﾌﾞﾗｹｯﾄ・電源ｹｰﾌﾞﾙ・FG線取付け【OP:ﾄﾚｲ仕様】",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WEPJ-G002-D14",
"InspectionItems": [
"検査表①:3.ﾈｼﾞ締めﾄﾙｸ確認"
],
"WorkTypes": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾈｸﾀ中継ﾌﾞﾗｹｯﾄ・電源ｹｰﾌﾞﾙ・FG線取付け【OP:ﾄﾚｲ仕様】",
"WorkItems": [
"2. 電源ｹｰﾌﾞﾙを中継ﾌﾞﾗｹｯﾄに接続",
"■3. FG端子を②で固定する",
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [
"TRAY.PR",
"FGTR1"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"検査表①:3.ﾈｼﾞ締めﾄﾙｸ確認",
"WEPJ-G002-D14"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D14",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "電源ｹｰﾌﾞﾙ引き回し【OP:ﾄﾚｲ仕様】",
"WorkItems": [
"1. 標準ﾄﾞﾗｲﾊﾞｰ線と一緒に引き回しをする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR",
"WEPJ-G002-D14-"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回出来ていること",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D14-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "DC電源取付け",
"WorkItems": [
"1. SPACER をBOLT WASHER で取付ける",
"2. ②をBOLT WASHER で取付ける",
"3. ｹｰﾌﾞﾙを固定する"
],
"WorkPoints": [
"奥3ヵ所は固定用ｽﾍﾟｰｻｰにはめ込む"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "DC電源取付け",
"WorkItems": [
"1. SPACER をBOLT WASHER で取付ける",
"2. ②をBOLT WASHER で取付ける",
"3. ｹｰﾌﾞﾙを固定する"
],
"WorkPoints": [
"奥3ヵ所は固定用ｽﾍﾟｰｻｰにはめ込む"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "PLCｺﾝﾄﾛｰﾙ取付け",
"WorkItems": [
"1. RAIL にTERMINAL-BLOCK を取付ける",
"2. 1の完成品をBOLT WASHER で架台に取付ける"
],
"WorkPoints": [
"幅48mm",
"取付け方向に注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "PLCｺﾝﾄﾛｰﾙ取付け",
"WorkItems": [
"1. RAIL にTERMINAL-BLOCK を取付ける",
"2. 1の完成品をBOLT WASHER で架台に取付ける"
],
"WorkPoints": [
"幅48mm",
"取付け方向に注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "110cN･m",
"WorkName": "PLCｺﾝﾄﾛｰﾙ取付け",
"WorkItems": [
"3. PLCｺﾝﾄﾛｰﾙを取付ける",
"4. 3の状態にてTERMINAL-SUPPORT を当てつけて取付ける"
],
"WorkPoints": [
"TERMINAL-BLOCK に当てつける",
"取付け方向に注意",
"裏面のﾋﾟﾝを活用して取付け",
"下げ方向で開､上げ方向で閉",
"取付け方向に注意",
"上方向に押し上げながら締付ける"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"PLCｺﾝﾄﾛｰﾙ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｧｲﾊﾞｰ線投入・固定・接続",
"WorkItems": [
"1. ①をﾌﾛﾝﾄ側に投入",
"2. ①を接続する",
"3. ①を固定する"
],
"WorkPoints": [
"ここから投入する",
"ｹｰﾌﾞﾙの負荷に注意すること",
"6K302と7K302をﾌﾛﾝﾄ側に投入する"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D05",
"InspectionItems": [
"検査表①:6..Power Unit確認"
],
"WorkTypes": [],
"Words": [
"OPT2",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"REAR",
"OPT1",
"WEPJ-G002-D05"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D05",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.