input stringclasses 1 value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-5957",
"WorkName": "引き出部平面確認①",
"WorkItems": [
"1. 引き出部の高さを測定値にする",
"2. ①に㉖を接続する"
],
"WorkPoints": [
"ｹｰﾌﾞﾙﾍﾞｱからの配管と配線を接続する",
"配線4本接続する",
"BASE加工面からパレット搬送面を260㎜に㉗㉘㉙を使い合わせる",
"ﾚｷﾞｭﾚﾀｰ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5957",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "引き出部平面確認①",
"WorkItems": [
"1. 引き出部の高さを測定値にする",
"2. ①に㉖を接続する"
],
"WorkPoints": [
"ｹｰﾌﾞﾙﾍﾞｱからの配管と配線を接続する",
"配線4本接続する",
"BASE加工面からパレット搬送面を260㎜に㉗㉘㉙を使い合わせる",
"ﾚｷﾞｭﾚﾀｰ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "260㎜の位置にあること",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "治具ﾊﾟﾚｯﾄ",
"Size": "",
"ToolOther": "FM-5993",
"WorkName": "引き出部平面確認②-1",
"WorkItems": [
"2. ①の引き出部に㉖をセットし㉚をセットする",
"2. ①の引き出部に㉖をセットし㉚をセットする",
"1. ①に㉗を取付ける",
"3. 引き出部0°平面度測定"
],
"WorkPoints": [
"0.1mm以内",
"0.1mm以内",
"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"0.1mm以内",
"0.1mm以内",
"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"付属ﾈｼﾞで取付ける",
"SS軸出側､SR軸0°",
"SS軸出側､下記A,Bを測定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:4.引き出し部ﾊﾟﾚｯﾄ搬送面の平面度確認1"
]
} | {
"QualityItem": "実装確認",
"ToolManageNo": "FM-5993",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り開始する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部平面度調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5958",
"WorkName": "引き出部平面確認②-1",
"WorkItems": [
"1. ①に㉗を取付ける",
"3. 引き出部0°平面度測定",
"2. ①の引き出部に㉖をセットし㉚をセットする",
"1. ①に㉗を取付ける",
"3. 引き出部0°平面度測定"
],
"WorkPoints": [
"付属ﾈｼﾞで取付ける",
"SS軸出側､SR軸0°",
"SS軸出側､下記A,Bを測定する",
"0.1mm以内",
"0.1mm以内",
"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"付属ﾈｼﾞで取付ける",
"SS軸出側､SR軸0°",
"SS軸出側､下記A,Bを測定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:4.引き出し部ﾊﾟﾚｯﾄ搬送面の平面度確認1",
"検査表①:4.引き出し部ﾊﾟﾚｯﾄ搬送面の平面度確認1"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5958",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "-",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "引き出部平面確認②-1",
"WorkItems": [
"2. ①の引き出部に㉖をセットし㉚をセットする",
"2. ①の引き出部に㉖をセットし㉚をセットする",
"1. ①に㉗を取付ける",
"3. 引き出部0°平面度測定"
],
"WorkPoints": [
"0.1mm以内",
"0.1mm以内",
"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"0.1mm以内",
"0.1mm以内",
"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"付属ﾈｼﾞで取付ける",
"SS軸出側､SR軸0°",
"SS軸出側､下記A,Bを測定する"
],
"Tolks": [],
"InspectionNo": "WEMA-G002-C10",
"InspectionItems": [
"検査表①:4.引き出し部ﾊﾟﾚｯﾄ搬送面の平面度確認1"
],
"WorkTypes": [],
"Words": [
"WEMA-G002-C10"
]
} | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "基準0.1㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEMA-G002-C10",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲｽﾄｯｶｰ引き出部動作確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5874",
"WorkName": "引き出部平面確認②-1",
"WorkItems": [
"2. ①の引き出部に㉖をセットし㉚をセットする",
"1. ①に㉗を取付ける",
"3. 引き出部0°平面度測定"
],
"WorkPoints": [
"0.1mm以内",
"0.1mm以内",
"てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"付属ﾈｼﾞで取付ける",
"SS軸出側､SR軸0°",
"SS軸出側､下記A,Bを測定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:4.引き出し部ﾊﾟﾚｯﾄ搬送面の平面度確認1"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5874",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "引き出部平面確認②-2",
"WorkItems": [
"1. ㉛で SR軸０°、SS軸出側にする",
"3. 引き出部平面度調整",
"4. 平面度測定"
],
"WorkPoints": [
"止めﾈｼﾞ",
"調整ﾈｼﾞM6",
"固定ﾈｼﾞM6",
"1,SW ↑ ↓ ↑ ↓",
"止めﾈｼﾞ",
"固定ﾈｼﾞM6",
"※側面の固定ﾈｼﾞM6を緩め手前の止めﾈｼﾞを緩めて下部調整ﾈｼﾞで平面度を調整する",
"ﾘﾌﾄ部の引き出部取付ﾌﾞﾗｹｯﾄを調整し平面度を出す",
"調整ﾈｼﾞM6",
"0.1㎜以内",
"調整後の平面度A,Bの測定をする",
"平面度が出たら㉜で固定ネジのみトルク締めする※再調整の可能性がある為（SR軸90°確認後全てトルク締め）",
"止めねじ奥にｽﾍﾟｰｻｰが入っている為､緩め過ぎないこと"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "基準0.1㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "治具ﾊﾟﾚｯﾄ",
"Size": "",
"ToolOther": "FM-5993",
"WorkName": "引き出部平面確認②-2",
"WorkItems": [
"1. ㉛で SR軸０°、SS軸出側にする",
"3. 引き出部平面度調整",
"4. 平面度測定"
],
"WorkPoints": [
"止めﾈｼﾞ",
"調整ﾈｼﾞM6",
"固定ﾈｼﾞM6",
"1,SW ↑ ↓ ↑ ↓",
"止めﾈｼﾞ",
"固定ﾈｼﾞM6",
"※側面の固定ﾈｼﾞM6を緩め手前の止めﾈｼﾞを緩めて下部調整ﾈｼﾞで平面度を調整する",
"ﾘﾌﾄ部の引き出部取付ﾌﾞﾗｹｯﾄを調整し平面度を出す",
"調整ﾈｼﾞM6",
"0.1㎜以内",
"調整後の平面度A,Bの測定をする",
"平面度が出たら㉜で固定ネジのみトルク締めする※再調整の可能性がある為（SR軸90°確認後全てトルク締め）",
"止めねじ奥にｽﾍﾟｰｻｰが入っている為､緩め過ぎないこと"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5993",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "正常に取付いている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部平面度調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5958",
"WorkName": "引き出部平面確認②-2",
"WorkItems": [
"1. ㉛で SR軸０°、SS軸出側にする",
"3. 引き出部平面度調整",
"4. 平面度測定"
],
"WorkPoints": [
"止めﾈｼﾞ",
"調整ﾈｼﾞM6",
"固定ﾈｼﾞM6",
"1,SW ↑ ↓ ↑ ↓",
"止めﾈｼﾞ",
"固定ﾈｼﾞM6",
"※側面の固定ﾈｼﾞM6を緩め手前の止めﾈｼﾞを緩めて下部調整ﾈｼﾞで平面度を調整する",
"ﾘﾌﾄ部の引き出部取付ﾌﾞﾗｹｯﾄを調整し平面度を出す",
"調整ﾈｼﾞM6",
"0.1㎜以内",
"調整後の平面度A,Bの測定をする",
"平面度が出たら㉜で固定ネジのみトルク締めする※再調整の可能性がある為（SR軸90°確認後全てトルク締め）",
"止めねじ奥にｽﾍﾟｰｻｰが入っている為､緩め過ぎないこと"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5958",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲｽﾄｯｶｰ引き出部動作確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5874",
"WorkName": "引き出部平面確認②-2",
"WorkItems": [
"2. ①に㉙を載せ測定位置A、Bに㉘をセットする"
],
"WorkPoints": [
"平面度0.1㎜以内",
"Ａ、Bを測定し低い方を基準として㉘を２個セットする",
"この3箇所を緩めて調整を行う"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5874",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "引き出部平面確認②-2",
"WorkItems": [
"1. ㉛で SR軸０°、SS軸出側にする",
"3. 引き出部平面度調整"
],
"WorkPoints": [
"1,SW ↑ ↓ ↑ ↓",
"止めﾈｼﾞ",
"固定ﾈｼﾞM6",
"※側面の固定ﾈｼﾞM6を緩め手前の止めﾈｼﾞを緩めて下部調整ﾈｼﾞで平面度を調整する",
"ﾘﾌﾄ部の引き出部取付ﾌﾞﾗｹｯﾄを調整し平面度を出す"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "0.6N･m",
"WorkName": "引き出部平面確認②-3",
"WorkItems": [
"3. ﾎﾞﾙﾄ締付"
],
"WorkPoints": [
"平面度が規格値外の場合は再度調整をする｡SS軸出側:SR軸0°とSS軸戻側:SR軸90°で規格内になるまで再調整する",
"調整ﾈｼﾞM6",
"固定ﾈｼﾞM6",
"1,SW ↑ ↓ ↓ ↑",
"固定ﾈｼﾞM6",
"調整ﾈｼﾞM6",
"1,調整ネジM6を㉘でトルク締めする",
"平面度が規格値0.1mm以内であれば調整時に緩めたﾈｼﾞを本締めし､SS軸出側:SR軸0°とSS軸戻側:SR軸90°の再測定をする",
"2,調整ネジM6を㉗でトルク締めする"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各0.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "引き出部平面確認②-3",
"WorkItems": [
"3. ﾎﾞﾙﾄ締付"
],
"WorkPoints": [
"平面度が規格値外の場合は再度調整をする｡SS軸出側:SR軸0°とSS軸戻側:SR軸90°で規格内になるまで再調整する",
"調整ﾈｼﾞM6",
"固定ﾈｼﾞM6",
"1,SW ↑ ↓ ↓ ↑",
"固定ﾈｼﾞM6",
"調整ﾈｼﾞM6",
"1,調整ネジM6を㉘でトルク締めする",
"平面度が規格値0.1mm以内であれば調整時に緩めたﾈｼﾞを本締めし､SS軸出側:SR軸0°とSS軸戻側:SR軸90°の再測定をする",
"2,調整ネジM6を㉗でトルク締めする"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "40cN･m",
"WorkName": "引き出部平面確認②-3",
"WorkItems": [
"3. ﾎﾞﾙﾄ締付"
],
"WorkPoints": [
"平面度が規格値外の場合は再度調整をする｡SS軸出側:SR軸0°とSS軸戻側:SR軸90°で規格内になるまで再調整する",
"調整ﾈｼﾞM6",
"固定ﾈｼﾞM6",
"1,SW ↑ ↓ ↓ ↑",
"固定ﾈｼﾞM6",
"調整ﾈｼﾞM6",
"1,調整ネジM6を㉘でトルク締めする",
"平面度が規格値0.1mm以内であれば調整時に緩めたﾈｼﾞを本締めし､SS軸出側:SR軸0°とSS軸戻側:SR軸90°の再測定をする",
"2,調整ネジM6を㉗でトルク締めする"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "引き出部平面確認②-3",
"WorkItems": [
"2. 平面度測定",
"1. ㉝でSS軸戻側、SR軸90°にする",
"3. ﾎﾞﾙﾄ締付"
],
"WorkPoints": [
"0.1㎜以内",
"A,Bの平面度を測定する",
"SS軸戻側､SR軸90°",
"止めﾈｼﾞ",
"調整ﾈｼﾞM6",
"固定ﾈｼﾞM6",
"2,SW ↓ ↑",
"平面度が規格値外の場合は再度調整をする｡SS軸出側:SR軸0°とSS軸戻側:SR軸90°で規格内になるまで再調整する",
"調整ﾈｼﾞM6",
"固定ﾈｼﾞM6",
"1,SW ↑ ↓ ↓ ↑",
"固定ﾈｼﾞM6",
"調整ﾈｼﾞM6",
"1,調整ネジM6を㉘でトルク締めする",
"平面度が規格値0.1mm以内であれば調整時に緩めたﾈｼﾞを本締めし､SS軸出側:SR軸0°とSS軸戻側:SR軸90°の再測定をする",
"2,調整ネジM6を㉗でトルク締めする"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.1㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "治具ﾊﾟﾚｯﾄ",
"Size": "",
"ToolOther": "FM-5993",
"WorkName": "引き出部平面確認②-3",
"WorkItems": [
"2. 平面度測定",
"1. ㉝でSS軸戻側、SR軸90°にする",
"3. ﾎﾞﾙﾄ締付"
],
"WorkPoints": [
"0.1㎜以内",
"A,Bの平面度を測定する",
"SS軸戻側､SR軸90°",
"止めﾈｼﾞ",
"調整ﾈｼﾞM6",
"固定ﾈｼﾞM6",
"2,SW ↓ ↑",
"平面度が規格値外の場合は再度調整をする｡SS軸出側:SR軸0°とSS軸戻側:SR軸90°で規格内になるまで再調整する",
"調整ﾈｼﾞM6",
"固定ﾈｼﾞM6",
"1,SW ↑ ↓ ↓ ↑",
"固定ﾈｼﾞM6",
"調整ﾈｼﾞM6",
"1,調整ネジM6を㉘でトルク締めする",
"平面度が規格値0.1mm以内であれば調整時に緩めたﾈｼﾞを本締めし､SS軸出側:SR軸0°とSS軸戻側:SR軸90°の再測定をする",
"2,調整ネジM6を㉗でトルク締めする"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認確認",
"ToolManageNo": "FM-5993",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部平面度調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5958",
"WorkName": "引き出部平面確認②-3",
"WorkItems": [
"2. 平面度測定",
"1. ㉝でSS軸戻側、SR軸90°にする",
"3. ﾎﾞﾙﾄ締付"
],
"WorkPoints": [
"0.1㎜以内",
"A,Bの平面度を測定する",
"SS軸戻側､SR軸90°",
"止めﾈｼﾞ",
"調整ﾈｼﾞM6",
"固定ﾈｼﾞM6",
"2,SW ↓ ↑",
"平面度が規格値外の場合は再度調整をする｡SS軸出側:SR軸0°とSS軸戻側:SR軸90°で規格内になるまで再調整する",
"調整ﾈｼﾞM6",
"固定ﾈｼﾞM6",
"1,SW ↑ ↓ ↓ ↑",
"固定ﾈｼﾞM6",
"調整ﾈｼﾞM6",
"1,調整ネジM6を㉘でトルク締めする",
"平面度が規格値0.1mm以内であれば調整時に緩めたﾈｼﾞを本締めし､SS軸出側:SR軸0°とSS軸戻側:SR軸90°の再測定をする",
"2,調整ネジM6を㉗でトルク締めする"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5958",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲｽﾄｯｶｰ引き出部動作確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5874",
"WorkName": "引き出部平面確認②-3",
"WorkItems": [
"2. 平面度測定",
"1. ㉝でSS軸戻側、SR軸90°にする",
"3. ﾎﾞﾙﾄ締付"
],
"WorkPoints": [
"0.1㎜以内",
"A,Bの平面度を測定する",
"SS軸戻側､SR軸90°",
"止めﾈｼﾞ",
"調整ﾈｼﾞM6",
"固定ﾈｼﾞM6",
"2,SW ↓ ↑",
"平面度が規格値外の場合は再度調整をする｡SS軸出側:SR軸0°とSS軸戻側:SR軸90°で規格内になるまで再調整する",
"調整ﾈｼﾞM6",
"固定ﾈｼﾞM6",
"1,SW ↑ ↓ ↓ ↑",
"固定ﾈｼﾞM6",
"調整ﾈｼﾞM6",
"1,調整ネジM6を㉘でトルク締めする",
"平面度が規格値0.1mm以内であれば調整時に緩めたﾈｼﾞを本締めし､SS軸出側:SR軸0°とSS軸戻側:SR軸90°の再測定をする",
"2,調整ネジM6を㉗でトルク締めする"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5874",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾌﾚｰﾑ取付-1",
"WorkItems": [
"1. ①に②をBOLT BOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"BASEとﾌﾚｰﾑの端面を各場所で合わせること"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"2の拡大",
"4の拡大",
"5の拡大"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾌﾚｰﾑ取付-2",
"WorkItems": [
"1. ①のﾘﾌﾄ部とﾌﾚｰﾑをBOLT WASHER で固定する"
],
"WorkPoints": [
"1,ﾘﾌﾄ側のﾌﾞﾗｹｯﾄが動くようにﾈｼﾞを軽く緩める(2か所)",
"2,BOLT WASHER で仮固定する",
"3,ﾘﾌﾄ部上面からﾌﾚｰﾑ上面までの高さを24.8mmに合わせる",
"4,ﾘﾌﾄ部とﾌﾚｰﾑの隙間を7mm､側面を面合わせにする",
"5,調整した寸法がずれないように本締めする",
"※ﾘﾌﾄ部を押したり引っ張ったりしないこと!(ﾘﾌﾄ部の垂直を変化させない為)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"24.8㎜",
"7㎜"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ取付-2",
"WorkItems": [
"1. ①のﾘﾌﾄ部とﾌﾚｰﾑをBOLT WASHER で固定する"
],
"WorkPoints": [
"1,ﾘﾌﾄ側のﾌﾞﾗｹｯﾄが動くようにﾈｼﾞを軽く緩める(2か所)",
"2,BOLT WASHER で仮固定する",
"3,ﾘﾌﾄ部上面からﾌﾚｰﾑ上面までの高さを24.8mmに合わせる",
"4,ﾘﾌﾄ部とﾌﾚｰﾑの隙間を7mm､側面を面合わせにする",
"5,調整した寸法がずれないように本締めする",
"※ﾘﾌﾄ部を押したり引っ張ったりしないこと!(ﾘﾌﾄ部の垂直を変化させない為)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"24.8㎜",
"7㎜"
]
} | {
"QualityItem": "結束間長さ確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾘﾌﾄ部端面からﾌﾚｰﾑ端面を合わせる",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "7㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ取付-2",
"WorkItems": [
"1. ①のﾘﾌﾄ部とﾌﾚｰﾑをBOLT WASHER で固定する"
],
"WorkPoints": [
"1,ﾘﾌﾄ側のﾌﾞﾗｹｯﾄが動くようにﾈｼﾞを軽く緩める(2か所)",
"2,BOLT WASHER で仮固定する",
"3,ﾘﾌﾄ部上面からﾌﾚｰﾑ上面までの高さを24.8mmに合わせる",
"4,ﾘﾌﾄ部とﾌﾚｰﾑの隙間を7mm､側面を面合わせにする",
"5,調整した寸法がずれないように本締めする",
"※ﾘﾌﾄ部を押したり引っ張ったりしないこと!(ﾘﾌﾄ部の垂直を変化させない為)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"24.8㎜",
"7㎜"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "ﾘﾌﾄ部端面からﾌﾚｰﾑ端面までの高さを合わせる",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "7㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ取付-2",
"WorkItems": [
"1. ①のﾘﾌﾄ部とﾌﾚｰﾑをBOLT WASHER で固定する"
],
"WorkPoints": [
"1,ﾘﾌﾄ側のﾌﾞﾗｹｯﾄが動くようにﾈｼﾞを軽く緩める(2か所)",
"2,BOLT WASHER で仮固定する",
"3,ﾘﾌﾄ部上面からﾌﾚｰﾑ上面までの高さを24.8mmに合わせる",
"4,ﾘﾌﾄ部とﾌﾚｰﾑの隙間を7mm､側面を面合わせにする",
"5,調整した寸法がずれないように本締めする",
"※ﾘﾌﾄ部を押したり引っ張ったりしないこと!(ﾘﾌﾄ部の垂直を変化させない為)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"24.8㎜",
"7㎜"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "ﾘﾌﾄ部端面からﾌﾚｰﾑ端面までの高さを合わせる",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ｹｰﾌﾞﾙﾍﾞｱ取付",
"WorkItems": [
"1. ①のﾘﾌﾄ部にﾍﾞｱﾌﾟﾚｰﾄをBOLT WASHER で取付ける",
"3. 取付けたﾍﾞｱ部の配線を固定する",
"2. ①のフレーム部にベアをBOLT WASHER WASHER ㉒で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ｹｰﾌﾞﾙﾍﾞｱ取付",
"WorkItems": [
"1. ①のﾘﾌﾄ部にﾍﾞｱﾌﾟﾚｰﾄをBOLT WASHER で取付ける",
"3. 取付けたﾍﾞｱ部の配線を固定する",
"2. ①のフレーム部にベアをBOLT WASHER WASHER ㉒で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｱ部配線固定",
"WorkItems": [
"2. ①のフレーム部にベアをBOLT WASHER WASHER ㉒で取付ける",
"1. ①のﾘﾌﾄ部にﾍﾞｱﾌﾟﾚｰﾄをBOLT WASHER で取付ける",
"3. 取付けたﾍﾞｱ部の配線を固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管に負荷無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "26.5N･m",
"WorkName": "ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①に②をBOLT で取付ける"
],
"WorkPoints": [
"下からﾎﾞﾙﾄ止め",
"取付面に異物が無いこと",
"①のPINに②の穴を合わせる(2か所)"
],
"Tolks": [
"締付ﾄﾙｸ 26.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ部ﾏｳﾝﾄ取付",
"WorkItems": [
"1. ①にCABLE-SUPPORT を取付ける",
"2. ①にLABEL を貼付ける"
],
"WorkPoints": [
"寸法はﾗﾍﾞﾙの中心",
"CABLE-SUPPORT 取付14か所",
"ﾗﾍﾞﾙの向きに注意すること",
"20mm",
"20mm",
"13mm",
"44mm",
"32mm",
"5.5mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"図2",
"図1",
"図1",
"図2"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置にﾗﾍﾞﾙが貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "水準器",
"Size": "0.02㎜/目盛",
"ToolOther": "",
"WorkName": "制御BOX取付",
"WorkItems": [
"2. ﾚﾍﾞﾙを確認し検査書に記入"
],
"WorkPoints": [
"4ヶ所",
"0.03mm/m以内"
],
"Tolks": [],
"InspectionNo": "WEMA-G002-C10",
"InspectionItems": [
"検査表①:2ﾍﾞｰｽのﾚﾍﾞﾙ確認3"
],
"WorkTypes": [],
"Words": [
"WEMA-G002-C10"
]
} | {
"QualityItem": "ﾚﾍﾞﾙ確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜/m以内",
"Method": "水準器",
"RecordMethod": "WEMA-G002-C10",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "制御BOX取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｹｰﾌﾞﾙを挟み込まないよう注意する"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾉｲｽﾞﾌｨﾙﾀｰ・ｱｰｽ板取付",
"WorkItems": [
"1. ①にNOISE-FILTER TERMINAL をBOLT WASHER で取付ける"
],
"WorkPoints": [
"TERMINAL はｱｰｽﾏｰｸを外側に向け取付ける",
"NOISE-FILTER は1,2と書いてある方を左側にし取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾏｶﾞｼﾞﾝ保持部､固定ｽﾄｯｸ部の高さ出しｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5954",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部B取付①",
"WorkItems": [
"1. ①に㉖㉗を取付"
],
"WorkPoints": [
"㉖ブロック治具",
"㉖ポスト治具",
"付属ﾈｼﾞで取付ける(M6×25､AW 2set)",
"㉖をピンに押し当付属ネジで下から取付ける（M8×60 2本）",
"取付面に異物が無いこと",
"取付面に異物が無いこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "設置確認",
"ToolManageNo": "FM-5954",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設置出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部B取付②",
"WorkItems": [
"5. ㉒WASHER で保持部プレートの高さを決める"
],
"WorkPoints": [
"下側からのｱﾝｸﾞﾙ緑〇3箇所",
"【締付手順】1.保持部ﾌﾟﾚｰﾄ側を締付け､ﾌﾚｰﾑ側を締付ける2.保持部ﾌﾟﾚｰﾄ側を緩めて､もう一度締め込む3.ﾌﾚｰﾑ側を緩め､締付けてﾄﾙｸをかける4.保持部ﾌﾟﾚｰﾄ側は次工程で調整する為､緩める ※本締めはSD-A039346-120_項目3で行う",
"ﾌﾞﾛｯｸ",
"※本締めはSD-A039346-120_項目3で行う"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "BASEX-YCHECKJIG-PLATE",
"Size": "",
"ToolOther": "FM-5921",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部B調整①",
"WorkItems": [
"1. ①に㉖㉗を取付"
],
"WorkPoints": [
"ﾘﾌﾄ部のLMｶﾞｲﾄﾞに当てつける",
"ｶﾞｲﾄﾞに押し当てる",
"ﾋﾟﾝに押し当て",
"ピンに押し当て、位置合わせ2を取付㉙で隙間確認",
"保持部側",
"引き出し部側",
"4ヶ所を付属ネジ（M4×16、AW､4set）で止める。押し当てた部分の隙間確認㉙",
"2ヶ所を付属ﾈｼﾞ(M6×30)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:6.保持部治具取付"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5921",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に取付けている事",
"Method": "位置合せ治具",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "BASEX-YCHECKJIG-BLOCK",
"Size": "",
"ToolOther": "FM-5920",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部B調整①",
"WorkItems": [
"1. ①に㉖㉗を取付"
],
"WorkPoints": [
"ﾘﾌﾄ部のLMｶﾞｲﾄﾞに当てつける",
"ｶﾞｲﾄﾞに押し当てる",
"ﾋﾟﾝに押し当て",
"ピンに押し当て、位置合わせ2を取付㉙で隙間確認",
"保持部側",
"引き出し部側",
"4ヶ所を付属ネジ（M4×16、AW､4set）で止める。押し当てた部分の隙間確認㉙",
"2ヶ所を付属ﾈｼﾞ(M6×30)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:6.保持部治具取付"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5920",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に取付けている事",
"Method": "位置合せ治具",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部B調整①",
"WorkItems": [
"1. ①に㉖㉗を取付"
],
"WorkPoints": [
"ﾘﾌﾄ部のLMｶﾞｲﾄﾞに当てつける",
"ｶﾞｲﾄﾞに押し当てる",
"ﾋﾟﾝに押し当て",
"ピンに押し当て、位置合わせ2を取付㉙で隙間確認",
"保持部側",
"引き出し部側",
"4ヶ所を付属ネジ（M4×16、AW､4set）で止める。押し当てた部分の隙間確認㉙",
"2ヶ所を付属ﾈｼﾞ(M6×30)"
],
"Tolks": [],
"InspectionNo": "WEMA-G002-C10",
"InspectionItems": [
"検査表①:6.保持部治具取付"
],
"WorkTypes": [],
"Words": [
"WEMA-G002-C10"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜以下",
"Method": "目視",
"RecordMethod": "WEMA-G002-C10",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部B調整②",
"WorkItems": [
"2. ﾌﾞﾚｰｷを解除しSL軸を保持部側の治具の高さに合わせる",
"3. 保持部を調整し､X方向の隙間とY方向の隙間を規格値内に調整する",
"4. 検査書No5-1_6ﾍﾟｰｼﾞを参考に取付確認",
"1. ①のSS軸を出す"
],
"WorkPoints": [
"指定している面が同じ高さになるようにSL軸を上げる",
"SD-A039346-118で取付けた項目2,3,4のﾈｼﾞを緩め保持部ﾌﾟﾚｰﾄの位置を調整し､項目2を本締め項目3,4のﾈｼﾞは締めるだけでOKである｡上記ﾈｼﾞを締めた状態で項目5_保持部側を本締めする｡",
"項目2",
"項目5",
"X方向㉖が通らないこと",
"0.01mmシックネス㉖が通らないこと",
"保持部側",
"引き出し部側",
"Y方向：㉛を当て㉗が入らないこと"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "WEMA-G002-C10",
"InspectionItems": [
"検査表①:5-1ﾏｶﾞｼﾞﾝ保持部B取付確認"
],
"WorkTypes": [],
"Words": [
"検査表①:7ﾏｶﾞｼﾞﾝ保持部取付確認2",
"WEMA-G002-C10"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEMA-G002-C10",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部B調整②",
"WorkItems": [
"2. ﾌﾞﾚｰｷを解除しSL軸を保持部側の治具の高さに合わせる",
"3. 保持部を調整し､X方向の隙間とY方向の隙間を規格値内に調整する",
"4. 検査書No5-1_6ﾍﾟｰｼﾞを参考に取付確認",
"1. ①のSS軸を出す"
],
"WorkPoints": [
"指定している面が同じ高さになるようにSL軸を上げる",
"SD-A039346-118で取付けた項目2,3,4のﾈｼﾞを緩め保持部ﾌﾟﾚｰﾄの位置を調整し､項目2を本締め項目3,4のﾈｼﾞは締めるだけでOKである｡上記ﾈｼﾞを締めた状態で項目5_保持部側を本締めする｡",
"項目2",
"項目5",
"X方向㉖が通らないこと",
"0.01mmシックネス㉖が通らないこと",
"保持部側",
"引き出し部側",
"Y方向：㉛を当て㉗が入らないこと"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "WEMA-G002-C10",
"InspectionItems": [
"検査表①:7ﾏｶﾞｼﾞﾝ保持部取付確認2"
],
"WorkTypes": [],
"Words": [
"検査表①:5-1ﾏｶﾞｼﾞﾝ保持部B取付確認",
"WEMA-G002-C10"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.2㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEMA-G002-C10",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部B調整②",
"WorkItems": [
"2. ﾌﾞﾚｰｷを解除しSL軸を保持部側の治具の高さに合わせる",
"3. 保持部を調整し､X方向の隙間とY方向の隙間を規格値内に調整する",
"4. 検査書No5-1_6ﾍﾟｰｼﾞを参考に取付確認",
"1. ①のSS軸を出す"
],
"WorkPoints": [
"指定している面が同じ高さになるようにSL軸を上げる",
"SD-A039346-118で取付けた項目2,3,4のﾈｼﾞを緩め保持部ﾌﾟﾚｰﾄの位置を調整し､項目2を本締め項目3,4のﾈｼﾞは締めるだけでOKである｡上記ﾈｼﾞを締めた状態で項目5_保持部側を本締めする｡",
"項目2",
"項目5",
"X方向㉖が通らないこと",
"0.01mmシックネス㉖が通らないこと",
"保持部側",
"引き出し部側",
"Y方向：㉛を当て㉗が入らないこと"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:5-1ﾏｶﾞｼﾞﾝ保持部B取付確認",
"検査表①:7ﾏｶﾞｼﾞﾝ保持部取付確認2"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部B調整②",
"WorkItems": [
"2. ﾌﾞﾚｰｷを解除しSL軸を保持部側の治具の高さに合わせる",
"3. 保持部を調整し､X方向の隙間とY方向の隙間を規格値内に調整する",
"4. 検査書No5-1_6ﾍﾟｰｼﾞを参考に取付確認",
"1. ①のSS軸を出す"
],
"WorkPoints": [
"指定している面が同じ高さになるようにSL軸を上げる",
"SD-A039346-118で取付けた項目2,3,4のﾈｼﾞを緩め保持部ﾌﾟﾚｰﾄの位置を調整し､項目2を本締め項目3,4のﾈｼﾞは締めるだけでOKである｡上記ﾈｼﾞを締めた状態で項目5_保持部側を本締めする｡",
"項目2",
"項目5",
"X方向㉖が通らないこと",
"0.01mmシックネス㉖が通らないこと",
"保持部側",
"引き出し部側",
"Y方向：㉛を当て㉗が入らないこと"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:5-1ﾏｶﾞｼﾞﾝ保持部B取付確認",
"検査表①:7ﾏｶﾞｼﾞﾝ保持部取付確認2"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "20㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部B調整②",
"WorkItems": [
"2. ﾌﾞﾚｰｷを解除しSL軸を保持部側の治具の高さに合わせる",
"3. 保持部を調整し､X方向の隙間とY方向の隙間を規格値内に調整する",
"4. 検査書No5-1_6ﾍﾟｰｼﾞを参考に取付確認",
"1. ①のSS軸を出す"
],
"WorkPoints": [
"指定している面が同じ高さになるようにSL軸を上げる",
"SD-A039346-118で取付けた項目2,3,4のﾈｼﾞを緩め保持部ﾌﾟﾚｰﾄの位置を調整し､項目2を本締め項目3,4のﾈｼﾞは締めるだけでOKである｡上記ﾈｼﾞを締めた状態で項目5_保持部側を本締めする｡",
"項目2",
"項目5",
"X方向㉖が通らないこと",
"0.01mmシックネス㉖が通らないこと",
"保持部側",
"引き出し部側",
"Y方向：㉛を当て㉗が入らないこと"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:5-1ﾏｶﾞｼﾞﾝ保持部B取付確認",
"検査表①:7ﾏｶﾞｼﾞﾝ保持部取付確認2"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "当てつける",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "治具ﾄﾚｲﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5913",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部B取付③",
"WorkItems": [
"1. ㉗を①にセットしX方向の調整"
],
"WorkPoints": [
"SD-A039346-119で取付けたBASE X-Y CHECK JIG-PLATEのピンの位置に㉗をセットする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:8ﾏｶﾞｼﾞﾝ保持部ｽﾗｲﾄﾞﾚｰﾙX方向位置調整"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5913",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部B取付③",
"WorkItems": [
"1. ㉗を①にセットしX方向の調整"
],
"WorkPoints": [
"SD-A039346-119で取付けたBASE X-Y CHECK JIG-PLATEのピンの位置に㉗をセットする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:8ﾏｶﾞｼﾞﾝ保持部ｽﾗｲﾄﾞﾚｰﾙX方向位置調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部B取付③",
"WorkItems": [
"1. ㉗を①にセットしX方向の調整"
],
"WorkPoints": [
"SD-A039346-119で取付けたBASE X-Y CHECK JIG-PLATEのピンの位置に㉗をセットする"
],
"Tolks": [],
"InspectionNo": "WEMA-G002-C10",
"InspectionItems": [
"検査表①:8ﾏｶﾞｼﾞﾝ保持部ｽﾗｲﾄﾞﾚｰﾙX方向位置調整"
],
"WorkTypes": [],
"Words": [
"WEMA-G002-C10"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が入らないこと",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEMA-G002-C10",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部A取付①",
"WorkItems": [
"2. ①に②をBOLT WASHER で取付",
"1. . SD-A039346-117で取付けた治具のﾈｼﾞを外し治具の向きを反転させﾏｶﾞｼﾞﾝ保持部Bのﾌﾟﾚｰﾄの支えにする"
],
"WorkPoints": [
"取付方向に注意すること外側からｱｸｾｽできること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾏｶﾞｼﾞﾝ保持部､固定ｽﾄｯｸ部の高さ出しｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5954",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部A取付②",
"WorkItems": [
"1. ①に㉘を取付"
],
"WorkPoints": [
"㉘ブロック治具",
"㉘ポスト治具",
"付属品ﾈｼﾞで取付ける(M4×16､AW 2set)",
"付属品ﾈｼﾞで取付ける(M6×20､AW)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5954",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "BASEX-YCHECKJIG-BLOCK",
"Size": "",
"ToolOther": "FM-5920",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部A取付③",
"WorkItems": [
"4. 保持部B側を緩め､ﾎﾟｽﾄ治具の位置を調整し保持部B側と保持部A側を止める",
"3. 保持部B側を緩め､ﾌﾞﾛｯｸ治具の位置を調整し保持部B側と保持部A側を止める",
"5. BOLT WASHER で保持部ﾌﾟﾚｰﾄの高さを決める",
"1. ①にSD-A039346-123で取付けた治具とSD-A039346-122で取付けたﾎﾟｽﾄの上に②を載せる",
"2. ②をPOST で取付",
"6. SD-A039346-119を参照し㉙を②に取付ける"
],
"WorkPoints": [
"ﾌﾞﾛｯｸ",
"下側からのｱﾝｸﾞﾙ緑〇3箇所",
"引き出し部",
"㉚が通らないこと",
"保持部B",
"保持部A",
"【締付手順】1.保持部ﾌﾟﾚｰﾄ側を締付け､ﾌﾚｰﾑ側を締付ける2.保持部ﾌﾟﾚｰﾄ側を緩めて､もう一度締め込む3.ﾌﾚｰﾑ側を緩め､締付けてﾄﾙｸをかける4.保持部ﾌﾟﾚｰﾄ側は次工程で調整する為､緩める ※本締めはSD-A039346-124_項目3で行う",
"付属品ﾈｼﾞで取付ける(M4×16､AW 2set)",
"付属品ﾈｼﾞで取付ける(M6×20､AW)",
"②を本体の下記方向より入れる"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WEMA-G002-C10",
"InspectionItems": [
"検査表①:6.保持部取付確認1"
],
"WorkTypes": [],
"Words": [
"WEMA-G002-C10"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5920",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りである事",
"Method": "目視",
"RecordMethod": "WEMA-G002-C10",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部A取付③",
"WorkItems": [
"6. SD-A039346-119を参照し㉙を②に取付ける"
],
"WorkPoints": [
"㉚が通らないこと",
"付属品ﾈｼﾞで取付ける(M6×20､AW)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:6.保持部取付確認1"
]
} | {
"QualityItem": "ｽｷﾏの確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部A取付③",
"WorkItems": [
"5. BOLT WASHER で保持部ﾌﾟﾚｰﾄの高さを決める"
],
"WorkPoints": [
"ﾌﾞﾛｯｸ",
"下側からのｱﾝｸﾞﾙ緑〇3箇所",
"【締付手順】1.保持部ﾌﾟﾚｰﾄ側を締付け､ﾌﾚｰﾑ側を締付ける2.保持部ﾌﾟﾚｰﾄ側を緩めて､もう一度締め込む3.ﾌﾚｰﾑ側を緩め､締付けてﾄﾙｸをかける4.保持部ﾌﾟﾚｰﾄ側は次工程で調整する為､緩める ※本締めはSD-A039346-124_項目3で行う"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部A調整",
"WorkItems": [
"2. ﾌﾞﾚｰｷを解除しSL軸を保持部側の治具の高さに合わせる",
"3. 保持部を調整し､X方向の隙間とY方向の隙間を規格値内に調整する",
"1. ①のSS軸を出す",
"4. 検査書No5-1_6ﾍﾟｰｼﾞを参考に取付確認"
],
"WorkPoints": [
"X方向㉖が通らないこと",
"保持部側",
"引き出し部側",
"指定している面が同じ高さになるようにSL軸を上げる",
"SD-A039346-124で取付けた項目2,3,4のﾈｼﾞを緩め保持部ﾌﾟﾚｰﾄの位置を調整し､項目2を本締め項目3,4のﾈｼﾞは締めるだけでOKである｡上記ﾈｼﾞを締めた状態で項目5_保持部側を本締めする｡",
"項目2",
"項目5",
"0.01mmシックネス㉖が通らないこと",
"Y方向：㉛を当て㉗が入らないこと"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:7ﾏｶﾞｼﾞﾝ保持部取付確認2",
"検査表①:5-2ﾏｶﾞｼﾞﾝ保持部A取付確認"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部A調整",
"WorkItems": [
"2. ﾌﾞﾚｰｷを解除しSL軸を保持部側の治具の高さに合わせる",
"3. 保持部を調整し､X方向の隙間とY方向の隙間を規格値内に調整する",
"1. ①のSS軸を出す",
"4. 検査書No5-1_6ﾍﾟｰｼﾞを参考に取付確認"
],
"WorkPoints": [
"X方向㉖が通らないこと",
"保持部側",
"引き出し部側",
"指定している面が同じ高さになるようにSL軸を上げる",
"SD-A039346-124で取付けた項目2,3,4のﾈｼﾞを緩め保持部ﾌﾟﾚｰﾄの位置を調整し､項目2を本締め項目3,4のﾈｼﾞは締めるだけでOKである｡上記ﾈｼﾞを締めた状態で項目5_保持部側を本締めする｡",
"項目2",
"項目5",
"0.01mmシックネス㉖が通らないこと",
"Y方向：㉛を当て㉗が入らないこと"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:7ﾏｶﾞｼﾞﾝ保持部取付確認2",
"検査表①:5-2ﾏｶﾞｼﾞﾝ保持部A取付確認"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.2㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部A調整",
"WorkItems": [
"2. ﾌﾞﾚｰｷを解除しSL軸を保持部側の治具の高さに合わせる",
"3. 保持部を調整し､X方向の隙間とY方向の隙間を規格値内に調整する",
"1. ①のSS軸を出す"
],
"WorkPoints": [
"X方向㉖が通らないこと",
"保持部側",
"引き出し部側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:7ﾏｶﾞｼﾞﾝ保持部取付確認2"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部A調整",
"WorkItems": [
"2. ﾌﾞﾚｰｷを解除しSL軸を保持部側の治具の高さに合わせる",
"3. 保持部を調整し､X方向の隙間とY方向の隙間を規格値内に調整する",
"1. ①のSS軸を出す"
],
"WorkPoints": [
"X方向㉖が通らないこと",
"保持部側",
"引き出し部側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:7ﾏｶﾞｼﾞﾝ保持部取付確認2"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "20㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部A調整",
"WorkItems": [
"2. ﾌﾞﾚｰｷを解除しSL軸を保持部側の治具の高さに合わせる",
"3. 保持部を調整し､X方向の隙間とY方向の隙間を規格値内に調整する",
"1. ①のSS軸を出す"
],
"WorkPoints": [
"X方向㉖が通らないこと",
"保持部側",
"引き出し部側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:7ﾏｶﾞｼﾞﾝ保持部取付確認2"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "当てつける",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "治具ﾄﾚｲﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5913",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部A取付④",
"WorkItems": [
"3. SD-A039346-123で取付けたﾎﾟｽﾄ治具とﾌﾞﾛｯｸ治具のﾈｼﾞを外しﾎﾟｽﾄ治具はねじ穴に被らないようにｽﾗｲﾄﾞさせる ﾌﾞﾛｯｸ治具は90°回して保持部Aのﾌﾟﾚｰﾄの支えにする",
"1. ㉗を①にセットしX方向の調整",
"4. ﾚﾍﾞﾙ確認",
"2. SD-A039346-119、124（項目6）で取付けた治具と㉗を取外す"
],
"WorkPoints": [
"SD-A039346-119で取付けたBASE X-Y CHECK JIG-BLOCKのピンの位置に㉗をセットする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:8ﾏｶﾞｼﾞﾝ保持部ｽﾗｲﾄﾞﾚｰﾙX方向位置調整"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5913",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部A取付④",
"WorkItems": [
"3. SD-A039346-123で取付けたﾎﾟｽﾄ治具とﾌﾞﾛｯｸ治具のﾈｼﾞを外しﾎﾟｽﾄ治具はねじ穴に被らないようにｽﾗｲﾄﾞさせる ﾌﾞﾛｯｸ治具は90°回して保持部Aのﾌﾟﾚｰﾄの支えにする",
"1. ㉗を①にセットしX方向の調整",
"4. ﾚﾍﾞﾙ確認",
"2. SD-A039346-119、124（項目6）で取付けた治具と㉗を取外す"
],
"WorkPoints": [
"SD-A039346-119で取付けたBASE X-Y CHECK JIG-BLOCKのピンの位置に㉗をセットする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:8ﾏｶﾞｼﾞﾝ保持部ｽﾗｲﾄﾞﾚｰﾙX方向位置調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部A取付④",
"WorkItems": [
"3. SD-A039346-123で取付けたﾎﾟｽﾄ治具とﾌﾞﾛｯｸ治具のﾈｼﾞを外しﾎﾟｽﾄ治具はねじ穴に被らないようにｽﾗｲﾄﾞさせる ﾌﾞﾛｯｸ治具は90°回して保持部Aのﾌﾟﾚｰﾄの支えにする",
"1. ㉗を①にセットしX方向の調整",
"4. ﾚﾍﾞﾙ確認",
"2. SD-A039346-119、124（項目6）で取付けた治具と㉗を取外す"
],
"WorkPoints": [
"SD-A039346-119で取付けたBASE X-Y CHECK JIG-BLOCKのピンの位置に㉗をセットする"
],
"Tolks": [],
"InspectionNo": "WEMA-G002-C10",
"InspectionItems": [
"検査表①:8ﾏｶﾞｼﾞﾝ保持部ｽﾗｲﾄﾞﾚｰﾙX方向位置調整"
],
"WorkTypes": [],
"Words": [
"WEMA-G002-C10"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜ｼｯｸﾈｽｹﾞｰｼﾞが入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEMA-G002-C10",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "水準器",
"Size": "0.02㎜/目盛",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝ保持部A取付④",
"WorkItems": [],
"WorkPoints": [
"SD-A039346-123で取付けた治具",
"保持部A",
"黒線の内側に気泡が入っていること",
"0.03mm/m以内"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:2ﾍﾞｰｽのﾚﾍﾞﾙ確認②"
]
} | {
"QualityItem": "ﾚﾍﾞﾙ調整",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜/m以内",
"Method": "水準器",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "ﾌﾞﾚｰｶｰ取付",
"WorkItems": [
"1. ①に取付いているﾌﾞﾚｰｶｰをBOLT WASHER で取付ける"
],
"WorkPoints": [
"視野1",
"視野1から見た位置",
"手前に押し当てて取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "制御BOX部配線固定",
"WorkItems": [
"1. ①の配線を固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管に負荷無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "50cN･m",
"WorkName": "ﾌﾚｰﾑ部配線固定",
"WorkItems": [
"1. ①の配線をｺﾈｸﾀﾌﾞﾗｹｯﾄに接続しWASHER BOLT NUT で固定する",
"2. 配線を固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾌﾄ部配線固定",
"WorkItems": [
"1. ①の配線をｾﾝｻｰに接続する",
"2. ①のﾓｰﾀｰ配線をｺﾈｸﾀﾌﾞﾗｹｯﾄに接続する"
],
"WorkPoints": [
"B1351R",
"B1350R",
"SL軸+OVRｾﾝｻｰ",
"SL軸ｰOVRｾﾝｻｰ",
"E401",
"M401",
"B401",
"B401に於いてはﾌﾞﾚｰｷ解除治具と接続されている為､SD-A039346-164の工程で差込む"
],
"Tolks": [],
"InspectionNo": "WEMA-G002-D04",
"InspectionItems": [
"検査表①:ｺﾈｸﾀ接続確認その5"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:ｺﾈｸﾀ接続確認その4",
"WEMA-G002-D04"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEMA-G002-D04",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "中継ｺﾈｸﾀ部配線固定",
"WorkItems": [
"1. ①の配線を中継ﾌﾞﾗｹｯﾄに接続する"
],
"WorkPoints": [
"2B1364P",
"1B1362P",
"1B1360P",
"1R460P"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管に負荷無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｱ部配線固定",
"WorkItems": [
"1. ①のﾍﾞｱ部配線を接続する"
],
"WorkPoints": [
"2B1364R",
"1B1362R",
"1B1360R",
"1R460R",
"ﾒﾝﾃﾅﾝｽSW配線ﾓｰﾀｰ動力､ｴﾝｺｰﾀﾞ線ﾒﾝﾃﾅﾝｽｶﾊﾞｰ安全SW配線",
"150mm"
],
"Tolks": [],
"InspectionNo": "WEMA-G002-D04",
"InspectionItems": [
"検査表①:ｺﾈｸﾀ接続確認その5"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WEMA-G002-D04"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEMA-G002-D04",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝﾄﾞｱ部配線固定",
"WorkItems": [
"1. ①の配線を接続する"
],
"WorkPoints": [
"S312",
"S311",
"ﾓｰﾀｰ動力､ｴﾝｺｰﾀﾞ線ﾒﾝﾃﾅﾝｽｶﾊﾞｰ安全SW配線は抜き穴を通し制御BOX側へ引き回す",
"S322",
"150mm"
],
"Tolks": [],
"InspectionNo": "WEMA-G002-D04",
"InspectionItems": [
"検査表①:ｺﾈｸﾀ接続確認その4"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WEMA-G002-D04"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEMA-G002-D04",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "制御BOX部配線固定",
"WorkItems": [
"1. ①の配線を接続する"
],
"WorkPoints": [
"S305",
"CNP3BK401",
"CN2BK401"
],
"Tolks": [],
"InspectionNo": "WEMA-G002-D04",
"InspectionItems": [
"検査表①:ｺﾈｸﾀ接続確認その5"
],
"WorkTypes": [],
"Words": [
"FG-CNP3BK401",
"W-CNP3BK401",
"V-CNP3BK401",
"U-CNP3BK401",
"CN2BK401",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WEMA-G002-D04"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEMA-G002-D04",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "No.2",
"ToolOther": "1.8N･m",
"WorkName": "ｱｰｽ配線接続",
"WorkItems": [
"1. ①の配線をSCREW で固定する"
],
"WorkPoints": [
"FGP",
"FGS",
"FGDC"
],
"Tolks": [
"締付ﾄﾙｸ 1.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｲｯﾁ締付けｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5255",
"WorkName": "ｽｲｯﾁ取付け",
"WorkItems": [
"1. ①にSWITCH を取付ける"
],
"WorkPoints": [
"△ﾏｰｸ",
"ｺﾈｸﾀ部",
"SW部",
"取付後､傾き無き事",
"取付け方向は△ﾏｰｸが上になる様取付ける",
"取付けﾘﾝｸﾞ"
],
"Tolks": [
"締付ﾄﾙｸ 147cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5255",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "FM-5255",
"ToolOther": "147cN･m",
"WorkName": "ｽｲｯﾁ取付け",
"WorkItems": [
"1. ①にSWITCH を取付ける"
],
"WorkPoints": [
"△ﾏｰｸ",
"ｺﾈｸﾀ部",
"SW部",
"取付後､傾き無き事",
"取付け方向は△ﾏｰｸが上になる様取付ける",
"取付けﾘﾝｸﾞ"
],
"Tolks": [
"締付ﾄﾙｸ 147cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "147cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝ補給完了SW配線固定",
"WorkItems": [
"1. ①の配線を接続する"
],
"WorkPoints": [
"S02R",
"S01R"
],
"Tolks": [],
"InspectionNo": "WEMA-G002-D04",
"InspectionItems": [
"検査表①:ｺﾈｸﾀ接続確認その4"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WEMA-G002-D04"
]
} | {
"QualityItem": "ｺﾈｸﾀ接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEMA-G002-D04",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "非常停止SW配線固定",
"WorkItems": [
"1. ①の配線を接続する"
],
"WorkPoints": [
"はめ込む"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管に負荷無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾏｶﾞｼﾞﾝ保持部､固定ｽﾄｯｸ部の高さ出しｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5954",
"WorkName": "固定ｽﾄｯｸ部取付①",
"WorkItems": [
"1. ①に㉘を仮固定する"
],
"WorkPoints": [
"㉘ブロック治具",
"付属品ﾈｼﾞで取付ける(M4×16､AW 2set)",
"㉘ポスト治具",
"付属品ﾈｼﾞで取付ける(M6×20､AW)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5954",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "BASEX-YCHECKJIG-BLOCK",
"Size": "",
"ToolOther": "FM-5920",
"WorkName": "固定ｽﾄｯｸ部取付②",
"WorkItems": [
"6. SD-A039346-119を参照し㉙を②に取付ける",
"1. ①にSD-A039346-139で取付けた治具とSD-A039346-124で取付けたﾎﾟｽﾄの上に②を載せる",
"5. ㉒WASHER で固定ストック部プレートの高さを決める",
"3. . 保持部A側を緩め､ﾌﾞﾛｯｸ治具の位置を調整し保持部A側と固定ｽﾄｯｸ側を止める",
"2. ②をBOLT WASHER で取付",
"4. 保持部A側を緩め､ﾎﾟｽﾄ治具の位置を調整し保持部A側と固定ｽﾄｯｸ側を止める"
],
"WorkPoints": [
"ﾌﾞﾛｯｸ",
"下側からのｱﾝｸﾞﾙ緑〇3箇所",
"②を本体の下記方向より入れる非常停止SWに注意すること",
"付属品ﾈｼﾞで取付ける(M4×16､AW 2set)",
"付属品ﾈｼﾞで取付ける(M6×20､AW)",
"【締付手順】1.保持部ﾌﾟﾚｰﾄ側を締付け､ﾌﾚｰﾑ側を締付ける2.保持部ﾌﾟﾚｰﾄ側を緩めて､もう一度締め込む3.ﾌﾚｰﾑ側を緩め､締付けてﾄﾙｸをかける4.保持部ﾌﾟﾚｰﾄ側は次工程で調整する為､緩める ※本締めはSD-A039346-141_項目2で行う",
"㉙が通らないこと"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:6.保持部治具取付"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5920",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りである事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "固定ｽﾄｯｸ部取付②",
"WorkItems": [
"6. SD-A039346-119を参照し㉙を②に取付ける",
"4. 保持部A側を緩め､ﾎﾟｽﾄ治具の位置を調整し保持部A側と固定ｽﾄｯｸ側を止める"
],
"WorkPoints": [
"㉙が通らないこと"
],
"Tolks": [],
"InspectionNo": "WEMA-G002-C10",
"InspectionItems": [
"検査表①:6.保持部治具取付"
],
"WorkTypes": [],
"Words": [
"WEMA-G002-C10"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEMA-G002-C10",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "固定ｽﾄｯｸ部取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "固定ｽﾄｯｸ部調整",
"WorkItems": [
"1. ①の ﾌﾞﾚｰｷを解除しSL軸を固定ｽﾄｯｸ側の治具の高さに合わせる",
"2. 固定ｽﾄｯｸ部を調整し､X方向の隙間とY方向の隙間を規格値内に調整する",
"5. ﾚﾍﾞﾙ確認",
"4. 全ての治具を取外す",
"3. 検査書No5-3_8ﾍﾟｰｼﾞを参考に取付確認"
],
"WorkPoints": [
"X方向㉖が通らないこと",
"指定している面が同じ高さになるようにSL軸を上げる",
"0.01mmｼｯｸﾈｽが通らないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:9固定ｽﾄｯｸ部取付確認",
"検査表①:5-3固定ｽﾄｯｸ部の取付確認",
"検査表①:2ﾍﾞｰｽのﾚﾍﾞﾙ確認②"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "固定ｽﾄｯｸ部調整",
"WorkItems": [
"1. ①の ﾌﾞﾚｰｷを解除しSL軸を固定ｽﾄｯｸ側の治具の高さに合わせる",
"2. 固定ｽﾄｯｸ部を調整し､X方向の隙間とY方向の隙間を規格値内に調整する",
"5. ﾚﾍﾞﾙ確認",
"4. 全ての治具を取外す",
"3. 検査書No5-3_8ﾍﾟｰｼﾞを参考に取付確認"
],
"WorkPoints": [
"X方向㉖が通らないこと",
"指定している面が同じ高さになるようにSL軸を上げる",
"0.01mmｼｯｸﾈｽが通らないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:9固定ｽﾄｯｸ部取付確認",
"検査表①:5-3固定ｽﾄｯｸ部の取付確認",
"検査表①:2ﾍﾞｰｽのﾚﾍﾞﾙ確認②"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.2㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "固定ｽﾄｯｸ部調整",
"WorkItems": [
"1. ①の ﾌﾞﾚｰｷを解除しSL軸を固定ｽﾄｯｸ側の治具の高さに合わせる",
"2. 固定ｽﾄｯｸ部を調整し､X方向の隙間とY方向の隙間を規格値内に調整する",
"5. ﾚﾍﾞﾙ確認"
],
"WorkPoints": [
"X方向㉖が通らないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:9固定ｽﾄｯｸ部取付確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "固定ｽﾄｯｸ部調整",
"WorkItems": [
"1. ①の ﾌﾞﾚｰｷを解除しSL軸を固定ｽﾄｯｸ側の治具の高さに合わせる",
"2. 固定ｽﾄｯｸ部を調整し､X方向の隙間とY方向の隙間を規格値内に調整する",
"5. ﾚﾍﾞﾙ確認"
],
"WorkPoints": [
"X方向㉖が通らないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:9固定ｽﾄｯｸ部取付確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "20㎜",
"ToolOther": "",
"WorkName": "固定ｽﾄｯｸ部調整",
"WorkItems": [
"1. ①の ﾌﾞﾚｰｷを解除しSL軸を固定ｽﾄｯｸ側の治具の高さに合わせる",
"2. 固定ｽﾄｯｸ部を調整し､X方向の隙間とY方向の隙間を規格値内に調整する",
"5. ﾚﾍﾞﾙ確認",
"4. 全ての治具を取外す",
"3. 検査書No5-3_8ﾍﾟｰｼﾞを参考に取付確認"
],
"WorkPoints": [
"X方向㉖が通らないこと",
"指定している面が同じ高さになるようにSL軸を上げる",
"0.01mmｼｯｸﾈｽが通らないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:9固定ｽﾄｯｸ部取付確認",
"検査表①:5-3固定ｽﾄｯｸ部の取付確認",
"検査表①:2ﾍﾞｰｽのﾚﾍﾞﾙ確認②"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "当てつける",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "水準器",
"Size": "0.02㎜/目盛",
"ToolOther": "",
"WorkName": "固定ｽﾄｯｸ部調整",
"WorkItems": [
"4. 全ての治具を取外す",
"1. ①の ﾌﾞﾚｰｷを解除しSL軸を固定ｽﾄｯｸ側の治具の高さに合わせる",
"2. 固定ｽﾄｯｸ部を調整し､X方向の隙間とY方向の隙間を規格値内に調整する",
"3. 検査書No5-3_8ﾍﾟｰｼﾞを参考に取付確認",
"5. ﾚﾍﾞﾙ確認"
],
"WorkPoints": [
"指定している面が同じ高さになるようにSL軸を上げる",
"X方向㉖が通らないこと",
"項目2",
"項目5",
"0.01mmｼｯｸﾈｽが通らないこと",
"SD-A039346-140で取付けた項目2,3,4のﾈｼﾞを緩め固定ｽﾄｯｸ部ﾌﾟﾚｰﾄの位置を調整し､項目2を本締め項目3,4のﾈｼﾞは締めるだけでOKである｡上記ﾈｼﾞを締めた状態で項目5_保持部側を本締めする｡",
"Y方向：㉛を当て㉗が入らないこと",
"黒線の内側に気泡が入っていること",
"0.03mm/m以内"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:9固定ｽﾄｯｸ部取付確認",
"検査表①:5-3固定ｽﾄｯｸ部の取付確認",
"検査表①:2ﾍﾞｰｽのﾚﾍﾞﾙ確認②"
]
} | {
"QualityItem": "ﾚﾍﾞﾙ調整",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜/m以内",
"Method": "水準器",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "固定ｽﾄｯｸ部取付③",
"WorkItems": [
"3. 下記位置を測定",
"1. ①の固定ｽﾄｯｸ部のﾌﾞﾗｹｯﾄをBOLT WASHER で取付"
],
"WorkPoints": [
"M3のﾈｼﾞを軽く緩めﾌﾚｰﾑに当てつけ締付ける",
"SL軸のブレーキを解除し下側の位置までSL軸を動かし㉚を当て0mmに合わせSL軸を動かし上側に移動し項目1でネジを緩めているので固定ストック上部を調整し0.1mm以内に調整し緩めたネジを締付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "固定ｽﾄｯｸ部取付③",
"WorkItems": [
"3. 下記位置を測定",
"1. ①の固定ｽﾄｯｸ部のﾌﾞﾗｹｯﾄをBOLT WASHER で取付"
],
"WorkPoints": [
"M3のﾈｼﾞを軽く緩めﾌﾚｰﾑに当てつけ締付ける",
"SL軸のブレーキを解除し下側の位置までSL軸を動かし㉚を当て0mmに合わせSL軸を動かし上側に移動し項目1でネジを緩めているので固定ストック上部を調整し0.1mm以内に調整し緩めたネジを締付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "固定ｽﾄｯｸ部取付③",
"WorkItems": [
"2. 引き出し部の下記位置に㉚㉛を取付",
"3. 下記位置を測定",
"1. ①の固定ｽﾄｯｸ部のﾌﾞﾗｹｯﾄをBOLT WASHER で取付"
],
"WorkPoints": [
"M3のﾈｼﾞを軽く緩めﾌﾚｰﾑに当てつけ締付ける",
"SL軸のブレーキを解除し下側の位置までSL軸を動かし㉚を当て0mmに合わせSL軸を動かし上側に移動し項目1でネジを緩めているので固定ストック上部を調整し0.1mm以内に調整し緩めたネジを締付ける"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WEMA-G002-C10",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1の拡大",
"WEMA-G002-C10"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.1㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEMA-G002-C10",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "固定ｽﾄｯｸ部取付④",
"WorkItems": [
"2. ①にCABLE-SUPPORT を取付",
"1. ①に②をBOLT WASHER で固定"
],
"WorkPoints": [
"ブラケットのR部分にはかからないように㉘を挟み込み押し当てて固定する",
"ﾋﾟﾝの端面からﾌﾞﾗｹｯﾄの端面まで80.5mm"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "1㎜",
"ToolOther": "",
"WorkName": "固定ｽﾄｯｸ部取付④",
"WorkItems": [
"2. ①にCABLE-SUPPORT を取付",
"1. ①に②をBOLT WASHER で固定"
],
"WorkPoints": [
"ブラケットのR部分にはかからないように㉘を挟み込み押し当てて固定する",
"ﾋﾟﾝの端面からﾌﾞﾗｹｯﾄの端面まで80.5mm"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "PINとの隙間:1㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "固定ｽﾄｯｸ部取付④",
"WorkItems": [
"2. ①にCABLE-SUPPORT を取付",
"1. ①に②をBOLT WASHER で固定"
],
"WorkPoints": [
"ブラケットのR部分にはかからないように㉘を挟み込み押し当てて固定する",
"ﾋﾟﾝの端面からﾌﾞﾗｹｯﾄの端面まで80.5mm"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:端面より80.5㎜±0.5",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｼｬｯﾀｰ駆動部取付①",
"WorkItems": [
"1. ①に②をCOLLAR BOLT WASHER で取付"
],
"WorkPoints": [
"BOLT →WASHER →ﾌﾞﾗｹｯﾄ→COLLAR の順序でﾌﾚｰﾑに取付ける",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"保持部プレートAとシャッターブラケットの間に㉘をハサミ込み位置出し中心位置になるので全体の隙間を見ながら調整",
"保持部ﾌﾟﾚｰﾄA",
"ｼｬｯﾀｰﾌﾞﾗｹｯﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "6.5㎜",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ駆動部取付①",
"WorkItems": [
"1. ①に②をCOLLAR BOLT WASHER で取付"
],
"WorkPoints": [
"BOLT →WASHER →ﾌﾞﾗｹｯﾄ→COLLAR の順序でﾌﾚｰﾑに取付ける",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"保持部プレートAとシャッターブラケットの間に㉘をハサミ込み位置出し中心位置になるので全体の隙間を見ながら調整",
"保持部ﾌﾟﾚｰﾄA",
"ｼｬｯﾀｰﾌﾞﾗｹｯﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "6.5㎜を挟み取付ける事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｼｬｯﾀｰ駆動部取付②",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"視野1下側から見た位置",
"右側に寄せて取付ける",
"視野1"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "ｼｬｯﾀｰ駆動部取付③",
"WorkItems": [
"1. ①にSTOPPER をBOLT WASHER で取付"
],
"WorkPoints": [
"視野1下側から見た位置",
"視野1",
"保持部ABのﾌﾟﾚｰﾄの端面に合わせて取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "2.0N･m",
"WorkName": "配線・配管用ﾏｳﾝﾄ取付",
"WorkItems": [
"2. ①にCABLE-SUPPORT をBOLT で取付",
"1. ①にCABLE-SUPPORT を取付"
],
"WorkPoints": [
"視野1",
"ﾏｶﾞｼﾞﾝ保持部Bを下側から見たCABLE-SUPPORT の取付位置",
"視野1下側から見た位置",
"左右に穴が来るように取付ける全て"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｴｱｰｾｯﾄ・ﾌｪﾗｲﾄｺｱ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付",
"■2. ①にNOISE-FILTER を固定する"
],
"WorkPoints": [
"ﾘﾌﾄ側に寄せて取付ける",
"2本のｹｰﾌﾞﾙL1CNP1K401L3CNP1K401にNOISE-FILTER を取付固定する"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "WEMA-G002-D03",
"InspectionItems": [
"検査表①:5:ﾌｪﾗｲﾄｺｱ型式確認及び取付確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"視野1",
"視野1",
"WEMA-G002-D03"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WEMA-G002-D03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｴｱｰｾｯﾄ・ﾌｪﾗｲﾄｺｱ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付",
"■2. ①にNOISE-FILTER を固定する"
],
"WorkPoints": [
"ﾘﾌﾄ側に寄せて取付ける",
"2本のｹｰﾌﾞﾙL1CNP1K401L3CNP1K401にNOISE-FILTER を取付固定する"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"視野1",
"視野1",
"検査表①:5:ﾌｪﾗｲﾄｺｱ型式確認及び取付確認",
"WEMA-G002-D03"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEMA-G002-D03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "ｴｱｰｾｯﾄ・ﾌｪﾗｲﾄｺｱ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付",
"■2. ①にNOISE-FILTER を固定する"
],
"WorkPoints": [
"ﾘﾌﾄ側に寄せて取付ける",
"2本のｹｰﾌﾞﾙL1CNP1K401L3CNP1K401にNOISE-FILTER を取付固定する"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"視野1",
"視野1",
"検査表①:5:ﾌｪﾗｲﾄｺｱ型式確認及び取付確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｺﾈｸﾀﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "連結部取付①",
"WorkItems": [
"1. ①にPIN をBOLT WASHER で取付",
"2. ①にPIN をBOLT WASHER で取付"
],
"WorkPoints": [
"PIN の取付方下記の用に治具1と治具2の距離を160.5mmのﾌﾞﾛｯｸｹﾞｰｼﾞを挟み込みPIN の位置を出す",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ6mm",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ6mmを治具2と本体ﾍﾞｰｽの間に挟み込み矢印の方向に当付ける",
"押し当て方向",
"PIN は6mmのﾌﾞﾛｯｸｹﾞｰｼﾞを挟み込み取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"図1",
"図1"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲｽﾄｯｶｰ連結部組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5955",
"WorkName": "連結部取付①",
"WorkItems": [
"1. ①にPIN をBOLT WASHER で取付",
"2. ①にPIN をBOLT WASHER で取付"
],
"WorkPoints": [
"PIN の取付方下記の用に治具1と治具2の距離を160.5mmのﾌﾞﾛｯｸｹﾞｰｼﾞを挟み込みPIN の位置を出す",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ6mm",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ6mmを治具2と本体ﾍﾞｰｽの間に挟み込み矢印の方向に当付ける",
"押し当て方向",
"PIN は6mmのﾌﾞﾛｯｸｹﾞｰｼﾞを挟み込み取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"図1",
"図1"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5955",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "160.5㎜",
"ToolOther": "",
"WorkName": "連結部取付①",
"WorkItems": [
"1. ①にPIN をBOLT WASHER で取付"
],
"WorkPoints": [
"PIN の取付方下記の用に治具1と治具2の距離を160.5mmのﾌﾞﾛｯｸｹﾞｰｼﾞを挟み込みPIN の位置を出す"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "160.5㎜を挟み込み取付ける事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "160.5㎜",
"ToolOther": "",
"WorkName": "連結部取付①",
"WorkItems": [
"1. ①にPIN をBOLT WASHER で取付"
],
"WorkPoints": [
"PIN の取付方下記の用に治具1と治具2の距離を160.5mmのﾌﾞﾛｯｸｹﾞｰｼﾞを挟み込みPIN の位置を出す"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "6㎜を挟み取付ける事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.