input stringclasses 1
value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "70cN･m",
"WorkName": "右側延長ｺﾝﾍﾞｱｶﾊﾞｰ取付け4(OP:延長ｺﾝﾍﾞｱ仕様、ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"4. 取り外したPCｶﾊﾞｰを取付ける",
"3. ﾚｰﾝ2も同様の作業を行う"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 5.0N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "70cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "右側延長ｺﾝﾍﾞｱｶﾊﾞｰ取付け5(OP:延長ｺﾝﾍﾞｱ仕様、ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [
"1. 可動ﾚｰﾙに㉖を当て、0にｾｯﾄする"
],
"WorkPoints": [
"PCｶﾊﾞｰにｷｽﾞ等無い事を確認する",
"㉖を確認しながら締め付ける",
"ｽﾞﾚ量:0.03㎜以内"
],
"Tolks": [
"締付ﾄﾙｸ 70cN･m",
... | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "ｽﾞﾚ量:0.03㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "右側延長ｺﾝﾍﾞｱｶﾊﾞｰ取付け5(OP:延長ｺﾝﾍﾞｱ仕様、ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [],
"WorkPoints": [
"PCｶﾊﾞｰにｷｽﾞ等無い事を確認する",
"㉖を確認しながら締め付ける",
"ｽﾞﾚ量:0.03㎜以内"
],
"Tolks": [
"締付ﾄﾙｸ 70cN･m",
"締付ﾄﾙｸ 5.0N･m",
"締付ﾄﾙｸ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "5.0N･m",
"WorkName": "右側延長ｺﾝﾍﾞｱｶﾊﾞｰ取付け5(OP:延長ｺﾝﾍﾞｱ仕様、ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [],
"WorkPoints": [
"PCｶﾊﾞｰにｷｽﾞ等無い事を確認する",
"㉖を確認しながら締め付ける",
"ｽﾞﾚ量:0.03㎜以内"
],
"Tolks": [
"締付ﾄﾙｸ 70cN･m",
"締付ﾄﾙｸ 5.0N･m",
"締付ﾄﾙｸ 194c... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "70cN･m",
"WorkName": "右側延長ｺﾝﾍﾞｱｶﾊﾞｰ取付け5(OP:延長ｺﾝﾍﾞｱ仕様、ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様)",
"WorkItems": [],
"WorkPoints": [
"PCｶﾊﾞｰにｷｽﾞ等無い事を確認する",
"㉖を確認しながら締め付ける",
"ｽﾞﾚ量:0.03㎜以内"
],
"Tolks": [
"締付ﾄﾙｸ 70cN･m",
"締付ﾄﾙｸ 5.0N･m",
"締付ﾄﾙｸ ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "70cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "払い出し",
"WorkItems": [
"1. ①②PLATE ⑦⑨⑩を4工程に払い出す"
],
"WorkPoints": [
"PLATE ⑦⑨⑩は17連台車切替仕様時のみ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾞｰｺｰﾄﾞｶﾒﾗｹｰﾌﾞﾙﾗﾍﾞﾙ取付",
"WorkItems": [
"1. CABLE にCABLE を取付ける"
],
"WorkPoints": [
"FAPC側:CN1K31D",
"CAMERA側:B3004"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾊﾞｰｺｰﾄﾞｶﾒﾗｱｰﾑ組立①",
"WorkItems": [
"2. 1.完成品にBRACKET をBOLT WASHER で取付ける",
"1. BLOCK にSHAFT をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words":... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "28±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "定盤",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾞｰｺｰﾄﾞｶﾒﾗｱｰﾑ組立①",
"WorkItems": [
"2. 1.完成品にBRACKET をBOLT WASHER で取付ける",
"1. BLOCK にSHAFT をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付出来ている事",
"Method": "定盤",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾊﾞｰｺｰﾄﾞｶﾒﾗｱｰﾑ組立②",
"WorkItems": [
"2. ①に1.完成品をBOLT WASHER で取付ける",
"1. PLATE にSHAFT をSCREW で取付ける"
],
"WorkPoints": [
"ｼｬﾌﾄの出代:4㎜",
"目安寸法:14㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "4±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾊﾞｰｺｰﾄﾞｶﾒﾗｱｰﾑ組立②",
"WorkItems": [
"2. ①に1.完成品をBOLT WASHER で取付ける",
"1. PLATE にSHAFT をSCREW で取付ける"
],
"WorkPoints": [
"ｼｬﾌﾄの出代:4㎜",
"目安寸法:14㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "14±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾞｰｺｰﾄﾞｶﾒﾗﾕﾆｯﾄ組立",
"WorkItems": [
"3. ①に2.完成品をBOLT WASHER で取付ける",
"▲2. LENS に㉗を塗布しCAMERA に締め込む",
"■1. CAMERA の型式を確認し､ｼﾘｱﾙNo.を記入する"
],
"WorkPoints": [
"型式:CSCX30BC3-10",
"ｼﾘｱﾙNO."
],
"Tolks": [],
"Inspecti... | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WDWS-5300-023",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｯｸﾀｲﾄ",
"Size": "",
"ToolOther": "243",
"WorkName": "ﾊﾞｰｺｰﾄﾞｶﾒﾗﾕﾆｯﾄ組立",
"WorkItems": [
"▲2. LENS に㉗を塗布しCAMERA に締め込む"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:安全部品確認",
"接着剤塗布 ｺﾞﾏ粒:3",
... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:3",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾊﾞｰｺｰﾄﾞｶﾒﾗﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"目安寸法:11㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "11±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾞｰｺｰﾄﾞｶﾒﾗｶﾒﾗｹｰﾌﾞﾙ接続",
"WorkItems": [
"1. ①に②を接続する"
],
"WorkPoints": [
"B3004",
"CAMERA側"
],
"Tolks": [],
"InspectionNo": "WDWS-5400-001",
"InspectionItems": [
"検査表①:接続ﾁｪｯｸ"
],
"WorkTypes": [],
"Wo... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WDWS-5400-001",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾞｰｺｰﾄﾞｶﾒﾗｶﾊﾞｰ取付",
"WorkItems": [
"2. 1.完成品にCOVER をBOLT WASHER で取付ける",
"1. ①にCOVER をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ｶﾒﾗｹｰﾌﾞﾙをｶﾊﾞｰのｽﾘｯﾄに通す",
"ｶﾊﾞｰ取付前に､ﾚﾝｽﾞのｶﾊﾞｰを取外す事",
"ﾚﾝｽﾞｶﾊﾞｰ(廃棄)",
"ﾚﾝｽﾞを保護する"
],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｼﾝ仕様確認",
"WorkItems": [
"2. 仕様書と実機が同じである事を確認し､検査表に記載する",
"1. S2出荷梱包ﾁｪｯｸﾘｽﾄを準備する"
],
"WorkPoints": [
"□にﾚを入れる",
"PLﾗﾍﾞﾙの言語電源電圧ｼｸﾞﾅﾙﾀﾜｰ搬送高さ基板流れ方向塗装色本体構成ｵﾌﾟｼｮﾝ仕様",
"ver.1.00を使用すること"
],
"Tolks": [],
"Inspect... | {
"QualityItem": "仕様確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-A06",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｼﾝｼﾘｱﾙ・ｵﾌﾟｼｮﾝ設定確認1",
"WorkItems": [
"1. 『ﾏｼﾝｼﾘｱﾙ番号』に入力されているｼﾘｱﾙNo.と ﾏｼﾝに貼られているｼﾘｱﾙNo.が一致しているか確認",
"2. ｼｽﾃﾑﾊﾞｰｼﾞｮﾝ画面を画像保存し､ﾌｫｰﾏｯﾄﾌｧｲﾙに 貼付けし､ﾌﾟﾘﾝﾄｱｳﾄした用紙を添付する",
"3. 『画像印刷SD出力』を『OFF』に設定",
"4. 『全体』のｵﾌﾟｼｮﾝ設定が全て『OFF』になっている事を確認",
... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-A06",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｼﾝｼﾘｱﾙ・ｵﾌﾟｼｮﾝ設定確認2",
"WorkItems": [
"2. 『ﾌｨｰﾀﾞｰ』のｵﾌﾟｼｮﾝ設定が全て『OFF』になっている事を確認",
"3. 『ﾍｯﾄﾞｶﾒﾗ』のｵﾌﾟｼｮﾝ設定が全て『OFF』になっている事を確認",
"4. 『ﾏﾙﾁ認識ｶﾒﾗ』のｵﾌﾟｼｮﾝ設定が全て『OFF』になっている事を確認",
"1. 『ｺﾝﾍﾞﾔ』のｵﾌﾟｼｮﾝ設定が全て『OFF』になっている事を確認",
"5. ①(各ﾕﾆｯﾄ)... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-A06",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷前準備(稼動情報・停止履歴・ﾒﾝﾃﾅﾝｽ履歴ﾘｾｯﾄ)1",
"WorkItems": [
"1. 『稼働情報』をｸﾘｱする",
"2. 『停止履歴』をｸﾘｱする",
"3. 『真空ｾﾝｻｴﾗｰ履歴』をｸﾘｱする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEAV-G002-A06",
"InspectionItems": [
"検査表①:出荷前確認... | {
"QualityItem": "出荷前確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-A06",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷前準備(稼動情報・停止履歴・ﾒﾝﾃﾅﾝｽ履歴ﾘｾｯﾄ)2",
"WorkItems": [
"1. 『ﾒﾝﾃﾅﾝｽ履歴』をｸﾘｱする",
"2. 『消耗部品』の『稼働時間』が『0』である事を確認"
],
"WorkPoints": [
"『0』である事",
"ﾒﾝﾃﾅﾝｽ-情報の内容はﾘｾｯﾄし無い事"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-A06",
"I... | {
"QualityItem": "出荷前確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-A06",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷前準備(製造年月日登録)",
"WorkItems": [
"1. 『製造年月日』を登録する",
"2. 『製造年月日』が変更されている事を確認"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"①ﾏｼﾝ",
"②情報",
"③... | {
"QualityItem": "出荷前確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷前準備(ｷｬﾘﾌﾞﾚｰｼｮﾝ履歴ﾘｾｯﾄ)",
"WorkItems": [
"1. 『ｷｬﾘﾌﾞﾚｰｼｮﾝ履歴』をｸﾘｱする",
"2. 『ｴﾝｼﾞﾆｱﾓｰﾄﾞ』に切り替え 『ｷｬﾘﾌﾞﾚｰｼｮﾝ履歴』が表示され無い事を確認"
],
"WorkPoints": [
"ｻｰﾋﾞｽﾏﾝﾓｰﾄﾞの場合､履歴は表示される"
],
"Tolks": [],
"InspectionNo": "",
"InspectionI... | {
"QualityItem": "出荷前確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷前準備(ﾏｼﾝﾊﾟﾗﾒｰﾀ保存)",
"WorkItems": [
"1. Parameter SDｶｰﾄﾞをﾏｼﾝに入れる",
"2. Parameter SDｶｰﾄﾞに『ﾏｼﾝﾊﾟﾗﾒｰﾀ』を保存する",
"4. Parameter SDｶｰﾄﾞに『ﾏｼﾝﾊﾟﾗﾒｰﾀ』が保存されたか確認",
"5. Parameter SDｶｰﾄﾞをﾏｼﾝから取り外す",
"6. SDｶｰﾄﾞにﾏｼﾝのｼﾘｱﾙNo.を記入する"
],
... | {
"QualityItem": "出荷前確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-A06",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷前確認(外観検査)",
"WorkItems": [
"1. ﾏｼﾝ全体に汚れ､傷､歪みが無い事を確認する",
"2. ﾘﾆｱｽｹｰﾙ､LMｶﾞｲﾄﾞに傷､汚れ､錆び､歪み､ｸﾞﾘｰｽの飛散が無いか確認する事"
],
"WorkPoints": [
"X軸 LMｶﾞｲﾄﾞ､ﾘﾆｱｽｹｰﾙ",
"Y軸 LMｶﾞｲﾄﾞ､ﾘﾆｱｽｹｰﾙ",
"操作ﾊﾟﾈﾙ部(F･R)",
"開閉ｶﾊﾞｰ部(F･R)",
... | {
"QualityItem": "出荷前確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-A06",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷前確認(取り外し確認)",
"WorkItems": [
"1. 台車､隣接信号､ｼｮｰﾄｺﾈｸﾀ 等が取り外されている事を確認する",
"2. 熱補正の先端ｶﾞﾗｽ部の傷､破損 等が無い事を確認する(ﾌﾛﾝﾄ･ﾘｱ)"
],
"WorkPoints": [
"交換台車",
"隣接信号ｼｮｰﾄｺﾈｸﾀ",
"交換台車ｼｮｰﾄｺﾈｸﾀ"
],
"Tolks": [],
"InspectionNo": "... | {
"QualityItem": "出荷前確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-A06",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷前確認(銘板ｼﾘｱﾙ品番・ｼﾘｱﾙNo.確認)",
"WorkItems": [
"■1. 銘板ｼﾘｱﾙの品番･ｼﾘｱﾙNo.を確認する"
],
"WorkPoints": [
"銘板ｼｰﾙの品番･ｼﾘｱﾙNo.をｼﾘｱﾙ手配表にて確認する事"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-A06",
"InspectionItems": [
"検査表①:出荷前確認"
... | {
"QualityItem": "出荷前確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-A06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷仕様確認(電圧ﾀｯﾌﾟ切り替え)1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "仕様確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN.m",
"WorkName": "出荷仕様確認(電圧ﾀｯﾌﾟ切り替え)1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷仕様確認(電圧ﾀｯﾌﾟ切り替え)2",
"WorkItems": [
"■2. ｵﾚﾝｼﾞ部をﾄﾞﾗｲﾊﾞｰで差込みｹｰﾌﾞﾙを抜く",
"■3. 出荷向けの仕様電圧端子台部にｹｰﾌﾞﾙを挿入する(U･V･W計3本)",
"■1. ｢仕様書｣と『制御かんばん』にてお客様の仕様電圧を確認し 200V以外であればﾀｯﾌﾟ切換えを実施する"
],
"WorkPoints": [
"ｽﾘｰﾌﾞ端子:絶縁被服部分の出代が3㎜以下",
... | {
"QualityItem": "仕様電圧確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "仕様書通りの事",
"Method": "目視",
"RecordMethod": "WEAV-G002-A06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "出荷仕様確認(電圧ﾀｯﾌﾟ切り替え)2",
"WorkItems": [
"■2. ｵﾚﾝｼﾞ部をﾄﾞﾗｲﾊﾞｰで差込みｹｰﾌﾞﾙを抜く",
"■3. 出荷向けの仕様電圧端子台部にｹｰﾌﾞﾙを挿入する(U･V･W計3本)",
"■1. ｢仕様書｣と『制御かんばん』にてお客様の仕様電圧を確認し 200V以外であればﾀｯﾌﾟ切換えを実施する"
],
"WorkPoints": [
"ｽﾘｰﾌﾞ端子:絶縁被服部分の出代が3... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3㎜以下",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "出荷仕様確認(電圧ﾀｯﾌﾟ切り替え)2",
"WorkItems": [
"■2. ｵﾚﾝｼﾞ部をﾄﾞﾗｲﾊﾞｰで差込みｹｰﾌﾞﾙを抜く",
"■3. 出荷向けの仕様電圧端子台部にｹｰﾌﾞﾙを挿入する(U･V･W計3本)",
"■1. ｢仕様書｣と『制御かんばん』にてお客様の仕様電圧を確認し 200V以外であればﾀｯﾌﾟ切換えを実施する"
],
"WorkPoints": [
"ｽﾘｰﾌﾞ端子:絶縁被服部分の出代... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "電圧設定確認治具",
"Size": "",
"ToolOther": "FM-6709~6714",
"WorkName": "出荷仕様確認(ﾀｯﾌﾟ切替え)③",
"WorkItems": [
"4. SD-EJM9D06-012で取外したｶﾊﾞｰを取付ける",
"2. 出荷向けの仕様電圧ｼｰﾙをｶﾊﾞｰに貼る",
"3. ﾄﾗﾝｽﾀｯﾌﾟ位置と仕様電圧ｼｰﾙの写真を撮り､所定のﾌｫﾙﾀﾞに格納する"
],
"WorkPoints": [
"治具のﾋﾟﾝを｢PR1 N1｣に挿入して､ﾋﾟﾝを視点に回転させる",
... | {
"QualityItem": "仕様確認",
"ToolManageNo": "FM-6709~6714",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出荷設定になっている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-A06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN･m",
"WorkName": "出荷仕様確認(ﾀｯﾌﾟ切替え)③",
"WorkItems": [
"4. SD-EJM9D06-012で取外したｶﾊﾞｰを取付ける",
"2. 出荷向けの仕様電圧ｼｰﾙをｶﾊﾞｰに貼る",
"3. ﾄﾗﾝｽﾀｯﾌﾟ位置と仕様電圧ｼｰﾙの写真を撮り､所定のﾌｫﾙﾀﾞに格納する"
],
"WorkPoints": [
"仕様､設定が一致している事",
"▼部に仕様電圧を合わす"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "各ﾗﾍﾞﾙの貼付け",
"WorkItems": [
"■1. ①のﾗﾍﾞﾙを貼付ける",
"■2. ②OR③OR④のﾗﾍﾞﾙを貼付ける",
"■1. ①のﾗﾍﾞﾙを貼付ける",
"■2. ②OR③OR④のﾗﾍﾞﾙを貼付ける"
],
"WorkPoints": [
"CE適合機のみ貼付け",
"CE適合機のみ貼付け"
],
"Tolks": [],
"InspectionNo": ... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "安全規格対応(ｱﾒﾘｶ/ｶﾅﾀﾞ向け)",
"WorkItems": [
"■1. LABEL LABEL が貼付いているか確認する｡"
],
"WorkPoints": [
"安全規格(NFPA79:ｱﾒﾘｶ/ｶﾅﾀﾞ向け)対応",
"引き当て変更時注意",
"10㎜",
"5㎜",
"2㎜"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-A06",
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示位置に貼ってあるか確認",
"Method": "目視",
"RecordMethod": "WEAV-G002-A06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾞﾘｰｽ塗布",
"WorkItems": [
"◆1. 本体摺動部にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"ｾﾝｻやｽｹｰﾙ等､他にｸﾞﾘｰｽが付かないように塗布する事",
"ﾏｸﾞﾈｯﾄ部に注意する事",
"X軸LMｶﾞｲﾄﾞ(ﾋﾞｰﾑ裏面)",
"基板ｺﾝﾍﾞｱ 幅寄せ部",
"水準器設置箇所(前後)",
"交換台車 駆動部(左右)",
"30連交換台車仕様",... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "防錆油塗布",
"WorkItems": [
"1. 本体に防錆油を塗布する"
],
"WorkPoints": [
"ﾍｯﾄﾞｵﾌﾟｼｮﾝ駆動部支柱",
"基板ｺﾝﾍﾞｱ ﾍﾞｰｽ部",
"防錆油が垂れない様にﾊｹにて塗布する事",
"ｾﾝｻ､ｽｹｰﾙ等 他に付かないように塗布する事",
"ﾏｸﾞﾈｯﾄ部に注意する事",
"廃棄BOX 支柱",
"ﾍｯﾄﾞｵﾌﾟｼｮﾝ駆動部",
"... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｴﾊﾞｰｽ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾏｼﾝ本体梱包1",
"WorkItems": [
"1. ﾘｱ右下ｶﾊﾞｰを開ける",
"2. ｴｱ配管を取り外す",
"3. ｴｱ配管に付属のｶﾌﾟﾗを取付け､ﾋﾞﾆｰﾙ袋に入れて梱包する",
"4. ﾘｱ右下ｶﾊﾞｰを閉める",
"7.ﾏﾙﾁ認識ｶﾒﾗ上にLABEL を置く",
"8. LABEL をTAPE でｶﾒﾗ上面ｶﾊﾞｰに貼付ける",
"5. ﾘｱ右下ｶﾊﾞｰにﾚ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "3ﾉｽﾞﾙﾍｯﾄﾞ固定",
"WorkItems": [
"1. ﾍｯﾄﾞ軸固定"
],
"WorkPoints": [
"固定時､負荷がかかり過ぎると変形等の恐れがある為､余裕を持たせて固定･結束を実施する事目安:手で紐の端を引いた際､20㎜程度動く事(図2)",
"固定紐長は約1600mm程度",
"各ﾍｯﾄﾞ毎に下図1の順番に梱包用固定紐を通し､固定する①.ﾍｯﾄﾞ左側下部(反射板の上)より紐を右側方向へ通す②.ﾍｯﾄﾞ左側よ... | {
"QualityItem": "固定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "4ﾉｽﾞﾙﾍｯﾄﾞ固定",
"WorkItems": [
"1. ﾍｯﾄﾞ軸の固定をする"
],
"WorkPoints": [
"固定時負荷がかかり過ぎると変形等の恐れがある為､余裕を持たせて固定･結束を実施する事目安:手で紐の端を引いた際20㎜程度動く事",
"固定紐は約1600㎜",
"ここから紐を通す",
"ここから紐を出す",
"A矢視",
"B矢視",
"ﾊﾞﾈに注意して紐を通す事... | {
"QualityItem": "固定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "LCRﾁｪｯｶｰ梱包①",
"WorkItems": [
"1. TAPE を2枚ｶｯﾄして貼り合わせる",
"2. LCRﾁｪｯｶｰの廃棄BOXﾌﾞﾗｹｯﾄ下側に1.完成品を敷く"
],
"WorkPoints": [
"135㎜±5㎜",
"貼り合わせの中心をﾌﾞﾗｹｯﾄ中心に敷く",
"ﾌﾞﾗｹｯﾄ端面合わせ"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "135㎜±5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LCRﾁｪｯｶｰ梱包②",
"WorkItems": [
"1. 廃棄BOXを置いてCUSHION を被せ､ﾃｰﾌﾟで貼り合わせる"
],
"WorkPoints": [
"廃棄BOX",
"CUSHION を半分に畳み､ﾚﾊﾞｰを下げてCUSHION を挟み込むこと",
"CUSHION :200×100"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り梱包されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｼﾝ本体梱包2",
"WorkItems": [
"3. X軸ﾌﾚｰﾑと架台をBRACKET BOLT で固定する",
"1. ﾏｼﾝ内にある部品廃棄BOXを梱包する",
"2. ﾍｯﾄﾞをWXBOLT BRACKET (WXSBOLT BRACKET )で固定する",
"3. X軸ﾌﾚｰﾑをWXBRACKET BOLT (WXSBRACKET BOLT )で固定する",
"4. ﾄﾚｲ仕様時支持部のﾄﾚｲ案内ﾊﾞｰを本体右側側面に... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｼﾝ本体梱包2",
"WorkItems": [
"3. X軸ﾌﾚｰﾑと架台をBRACKET BOLT で固定する",
"1. ﾏｼﾝ内にある部品廃棄BOXを梱包する",
"2. ﾍｯﾄﾞをWXBOLT BRACKET (WXSBOLT BRACKET )で固定する",
"3. X軸ﾌﾚｰﾑをWXBRACKET BOLT (WXSBRACKET BOLT )で固定する",
"4. ﾄﾚｲ仕様時支持部のﾄﾚｲ案内ﾊﾞｰを本体... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｼﾝ本体梱包2",
"WorkItems": [
"3. X軸ﾌﾚｰﾑと架台をBRACKET BOLT で固定する",
"1. ﾏｼﾝ内にある部品廃棄BOXを梱包する",
"2. ﾍｯﾄﾞをWXBOLT BRACKET (WXSBOLT BRACKET )で固定する",
"3. X軸ﾌﾚｰﾑをWXBRACKET BOLT (WXSBRACKET BOLT )で固定する",
"4. ﾄﾚｲ仕様時支持部のﾄﾚｲ案内ﾊﾞｰを本体... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｼﾝ本体梱包2",
"WorkItems": [
"3. X軸ﾌﾚｰﾑと架台をBRACKET BOLT で固定する",
"1. ﾏｼﾝ内にある部品廃棄BOXを梱包する",
"2. ﾍｯﾄﾞをWXBOLT BRACKET (WXSBOLT BRACKET )で固定する",
"3. X軸ﾌﾚｰﾑをWXBRACKET BOLT (WXSBRACKET BOLT )で固定する",
"4. ﾄﾚｲ仕様時支持部のﾄﾚｲ案内ﾊﾞｰを本体... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｼﾝ本体梱包2",
"WorkItems": [
"3. X軸ﾌﾚｰﾑと架台をBRACKET BOLT で固定する",
"1. ﾏｼﾝ内にある部品廃棄BOXを梱包する",
"2. ﾍｯﾄﾞをWXBOLT BRACKET (WXSBOLT BRACKET )で固定する",
"3. X軸ﾌﾚｰﾑをWXBRACKET BOLT (WXSBRACKET BOLT )で固定する",
"4. ﾄﾚｲ仕様時支持部のﾄﾚｲ案内ﾊﾞｰを本体... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｼﾝ本体梱包3",
"WorkItems": [
"2. ﾌｨｰﾀﾞｰｶﾊﾞｰをTAPE で固定する",
"1. 【延長ｺﾝﾍﾞｱ仕様】 本体との連結ｹｰﾌﾞﾙを外し､CUSHION TAPE にて梱包後､延長ｺﾝﾍﾞｱ内に収納してTAPE で固定する",
"3. ﾌｨｰﾀﾞｰｶﾊﾞｰをCUSHION TAPE で保護する(前後)",
"4 開閉ｶﾊﾞｰ部のﾏｸﾞﾈｯﾄｷｬｯﾁ部をCUSHION TAPE で保護する(前後)"
],
... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｼﾝ本体梱包4",
"WorkItems": [
"1. 操作ﾊﾟﾈﾙ部をCUSHION TAPE で保護する",
"2. ﾏｼﾝ本体にLABEL LABEL LABEL を貼付ける"
],
"WorkPoints": [
"ｴｱﾏｯﾄを2つ折りにし､4ヶ所をｶﾞﾑﾃｰﾌﾟでとめる",
"700㎜×400㎜:2枚",
"側面ｶﾊﾞｰ 4ヶ所",
"開閉ｶﾊﾞｰ上 3ヶ所",
"開閉ｶﾊﾞｰ 2ヶ所"
... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｼﾝ本体梱包5",
"WorkItems": [
"1. ｱｲﾎﾞﾙﾄｷｬｯﾌﾟをﾏｼﾝ本体にTAPE で固定する",
"2. 前後開閉ｶﾊﾞｰをTAPE で固定する",
"3. 前後開閉ｶﾊﾞｰをﾌｨｰﾀﾞｰｶﾊﾞｰとTAPE で固定する",
"4. ｴｱｰﾎｰｽをﾏｼﾝ本体にTAPE で固定する"
],
"WorkPoints": [
"A4袋にｷｬｯﾌﾟを入れ､2つ折りで閉じる",
"4方向とめ､剥がれが... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｼﾝ本体梱包6",
"WorkItems": [
"1. ｴｱｰﾎｰｽをﾏｼﾝ本体にCUSHION で固定する"
],
"WorkPoints": [
"ｴｱｰﾎｰｽは同搬物BOX､もしくは設備に接続されているものを用意",
"A3袋にｴｱｰﾎｰｽを入れ､2つ折りで閉じる",
"移送時に落下しないように貼付ける",
"ｵﾌﾟｼｮﾝ選択時対応"
],
"Tolks": [],
"InspectionNo"... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｼﾝ本体梱包7",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ梱包1(ｱｼﾞｬｽﾄﾎﾞﾙﾄの前準備)",
"WorkItems": [
"◆1. ADJUST-BOLT へｸﾞﾘｰｽを塗布する",
"2. PLATE へADJUST-BOLT を挿入する"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布部分は下図参照｡4個実施の事",
"ADJUST-BOLT のﾈｼﾞ山下限から30㎜程の部分まで挿入するﾅｯﾄは締め無い事｡4個制作の事"
],
"Tolks... | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ梱包1(ｱｼﾞｬｽﾄﾎﾞﾙﾄの前準備)",
"WorkItems": [
"◆1. ADJUST-BOLT へｸﾞﾘｰｽを塗布する",
"2. PLATE へADJUST-BOLT を挿入する"
],
"WorkPoints": [
"ｸﾞﾘｰｽ塗布部分は下図参照｡4個実施の事",
"ADJUST-BOLT のﾈｼﾞ山下限から30㎜程の部分まで挿入するﾅｯﾄは締め無い事｡4個制作の事"
],
"Tolks... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ梱包2(ｱｼﾞｬｽﾄﾎﾞﾙﾄのﾍﾞｰｽへの取付)",
"WorkItems": [
"1. ①の架台下側へ②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"各部外側へﾊﾞｶ穴分引きながら固定する"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m",
"締付ﾄﾙｸ 24.0N･m"
],
"InspectionNo": "",
"Inspectio... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "8㎜",
"ToolOther": "24.0N･m",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ梱包2(ｱｼﾞｬｽﾄﾎﾞﾙﾄのﾍﾞｰｽへの取付)",
"WorkItems": [
"1. ①の架台下側へ②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"各部外側へﾊﾞｶ穴分引きながら固定する"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m",
"締付ﾄﾙｸ 24.0N･m"
],
"InspectionNo": "",... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "24.0N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ梱包3(ｸﾞﾘｰｽ塗布)",
"WorkItems": [
"1. ｶﾊﾞｰを外す｡(4箇所)",
"◆2. LMｶﾞｲﾄﾞ6本､ﾎﾞｰﾙねじにｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"ｾﾝｻｰ等､他にｸﾞﾘｰｽが付かないように塗布する事",
"この4箇所のみﾎﾞﾙﾄ長さが他に比べ短い為､外す際､分けておく事",
"ﾘﾌﾄ軸ﾎﾞｰﾙねじ",
"吸着部上下LMｶﾞｲﾄﾞ(2本)... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ梱包4(防錆油確認)",
"WorkItems": [
"1. ﾌﾚｰﾑに防錆油が塗布されているか確認する｡",
"3. 外したｶﾊﾞｰを取付ける｡(4箇所)",
"2. ﾌﾚｰﾑ下部の開口部をCUSHION で塞ぎ､TAPE (5箇所)で固定する｡"
],
"WorkPoints": [
"この4箇所のみﾎﾞﾙﾄ長さが短い為､取付ける際､間違え無い事",
"必要に応じ､防錆油を薄く塗布する",
... | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｴﾊﾞｰｽ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ梱包5(輸送用固定ﾌﾞﾗｹｯﾄ取付-1)",
"WorkItems": [
"1. ①へBRACKET をBOLT で取付"
],
"WorkPoints": [
"BRACKET を吸着部ﾌﾟﾚｰﾄに仮取付固定する",
"1､①のﾘﾌﾄ部をﾚﾝﾁでﾘﾌﾄｱｯﾌﾟしながらBRACKET へ当てつける2､BRACKET とﾘﾌﾄの固定穴を合わせて仮固定する3､締付はSD-A013189-005にて締め付ける",
"UP... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ梱包5(輸送用固定ﾌﾞﾗｹｯﾄ取付-1)",
"WorkItems": [
"1. ①へBRACKET をBOLT で取付"
],
"WorkPoints": [
"BRACKET を吸着部ﾌﾟﾚｰﾄに仮取付固定する",
"1､①のﾘﾌﾄ部をﾚﾝﾁでﾘﾌﾄｱｯﾌﾟしながらBRACKET へ当てつける2､BRACKET とﾘﾌﾄの固定穴を合わせて仮固定する3､締付はSD-A013189-005にて締め付ける",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ梱包6(輸送用固定ﾌﾞﾗｹｯﾄ取付-2)",
"WorkItems": [
"1. ①へBRACKET BRACKET をBOLT で取付"
],
"WorkPoints": [
"BRACKET は引き出部ｶﾊﾞｰの下側穴より挿入｡BRACKET は吸着部取付ﾌﾟﾚｰﾄ溝から内側へ引き出部下へ挿入する",
"BRACKET は吸着部可動ﾌﾟﾚｰﾄの取付穴に合わせて固定する｡BRACKET は引き出部下のﾘﾌﾄ部ﾌﾚｰﾑの穴に... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ梱包6(輸送用固定ﾌﾞﾗｹｯﾄ取付-2)",
"WorkItems": [
"1. ①へBRACKET BRACKET をBOLT で取付"
],
"WorkPoints": [
"BRACKET は引き出部ｶﾊﾞｰの下側穴より挿入｡BRACKET は吸着部取付ﾌﾟﾚｰﾄ溝から内側へ引き出部下へ挿入する",
"BRACKET は吸着部可動ﾌﾟﾚｰﾄの取付穴に合わせて固定する｡BRACKET は引き出部下のﾘﾌﾄ部ﾌﾚ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ梱包7(輸送用固定ﾌﾞﾗｹｯﾄ取付-3)",
"WorkItems": [
"1. ①へBRACKET をBOLT で取付ける",
"2. ①へBRACKET をBOLT で取付",
"3. 作業2完了後ﾘﾌﾄ部のﾌﾞﾗｹｯﾄの増し締めを行う"
],
"WorkPoints": [
"ﾈｼﾞ穴を合わせる",
"引き出部駆動部",
"ﾘﾌﾄﾌﾚｰﾑ部",
"ﾏｶﾞｼﾞﾝ保持部側より作業の事... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ梱包7(輸送用固定ﾌﾞﾗｹｯﾄ取付-3)",
"WorkItems": [
"1. ①へBRACKET をBOLT で取付ける",
"1. ①へBRACKET をBOLT で取付ける",
"1. ①へBRACKET をBOLT で取付ける"
],
"WorkPoints": [
"ﾈｼﾞ穴を合わせる",
"引き出部駆動部",
"BRACKET は引き出部駆動部とﾘﾌﾄﾌﾚ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ梱包7(輸送用固定ﾌﾞﾗｹｯﾄ取付-4)",
"WorkItems": [
"1. ①へGUARD をBOLT で取付ける",
"2. ①へGUARD をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ梱包7(輸送用固定ﾌﾞﾗｹｯﾄ取付-4)",
"WorkItems": [
"1. ①へGUARD をBOLT で取付ける",
"2. ①へGUARD をBOLT で取付ける",
"1. ①へGUARD をBOLT で取付ける",
"2. ①へGUARD をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ梱包8(Iﾎﾞﾙﾄ取付)",
"WorkItems": [
"1. ①へBOLT を取付ける"
],
"WorkPoints": [
"止まるまで締め込み図の様に横になる様調整する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ梱包9(ｴｱｰﾏｯﾄ保護)",
"WorkItems": [
"1. ﾛｰﾚｯﾄ3個とｺﾞﾐ箱ｶﾞｲﾄﾞのﾎﾞﾙﾄ×2､ﾄﾚｲ連結ﾌﾞﾗｹｯﾄ×2(M8*16-3ヶ)を取外し､CUSHION TAPE で梱包する｡ ※ﾛｰﾚｯﾄはﾄﾚｲに付属される為､ﾄﾚｲ無仕様時は現物無し",
"2. ｺﾞﾐ箱部ﾎﾞｯｸｽに梱包したﾛｰﾚｯﾄ等をTAPE で固定し､ｺﾞﾐ箱部ﾎﾞｯｸｽをCUSHION TAPE で梱包する｡",
"3.... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞ梱包10(外観を静電ｼｰﾄで覆い注意ﾗﾍﾞﾙ貼付け)",
"WorkItems": [
"5. BAG の静電ｼｰﾄ (小)にて覆いTAPE で固定後､LABEL LABEL を貼付ける｡",
"1. 補給部の開口ｶﾊﾞｰをTAPE で固定する｡",
"3. 本体上部のﾛｰﾚｯﾄ取付ﾌﾞﾗｹｯﾄCUSHION で覆いTAPE で固定する｡(2箇所)",
"2. 連結ﾌﾞﾗｹｯﾄ部をCUSHION で覆いTAPE で固定し､LAB... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽLCG100",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄｸﾞﾘｰｽｱｯﾌﾟ1【ｽﾄｯｶｰ仕様】(海外出荷のみ)",
"WorkItems": [
"1. ①のｶﾊﾞｰを取外す",
"◆2. 各箇所にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"ﾘﾌﾄ軸ﾎﾞｰﾙﾈｼﾞ",
"ﾘﾌﾄ軸LMｶﾞｲﾄﾞ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItem... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布:ｸﾞﾘｰｽ容器各10㎜程度",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "ｸﾞﾘｰｽLCG100",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄｸﾞﾘｰｽｱｯﾌﾟ2【ｽﾄｯｶｰ仕様】(海外出荷のみ)",
"WorkItems": [
"◆1. 各箇所にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"引き出部 LMｶﾞｲﾄﾞ",
"吸着部 LMｶﾞｲﾄﾞ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布:ｸﾞﾘｰｽ容器各5㎜程度",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "80cN･m",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ防錆油塗布【ｽﾄｯｶｰ仕様】(海外出荷のみ)",
"WorkItems": [
"2. 外したｶﾊﾞｰを取付ける",
"1. ﾘﾌﾄﾌﾚｰﾑに防錆油が塗布されているか確認する"
],
"WorkPoints": [
"必要に応じ薄く塗布する"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m",
"締付ﾄﾙｸ 350cN･m",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.3",
"ToolOther": "350cN･m",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ防錆油塗布【ｽﾄｯｶｰ仕様】(海外出荷のみ)",
"WorkItems": [
"2. 外したｶﾊﾞｰを取付ける",
"1. ﾘﾌﾄﾌﾚｰﾑに防錆油が塗布されているか確認する"
],
"WorkPoints": [
"必要に応じ薄く塗布する"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m",
"締付ﾄﾙｸ 350cN･m",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "350cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ固定金具取付1【ｽﾄｯｶｰ仕様】",
"WorkItems": [
"1. ①にBRACKET をBOLT で取付ける"
],
"WorkPoints": [
"UP",
"DOWN",
"ﾚﾝﾁでﾘﾌﾄｱｯﾌﾟをしながら取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"In... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ固定金具取付2【ｽﾄｯｶｰ仕様】",
"WorkItems": [
"1. ①にBRACKET BRACKET をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Word... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ固定金具取付3【ｽﾄｯｶｰ仕様】",
"WorkItems": [
"1. ①にBRACKET BRACKET をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Word... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ固定金具取付4【ｽﾄｯｶｰ仕様】",
"WorkItems": [
"1. ①にGUARD GUARD をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ固定金具取付5【ｽﾄｯｶｰ仕様】",
"WorkItems": [
"1. ①にBOLT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ梱包1【ｽﾄｯｶｰ仕様】",
"WorkItems": [
"1. ①のﾉﾌﾞを3個取外しCUSHION で梱包する",
"2. 1完成品のｶﾊﾞｰとﾌﾞﾗｹｯﾄを外しCUSHION で梱包する"
],
"WorkPoints": [
"M8×20 AWを取付ける",
"M5×12 AWを袋に入れる",
"M6×10 ﾄﾗｽを袋に入れる",
"CUSHION 100×150",
... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ梱包2【ｽﾄｯｶｰ仕様】",
"WorkItems": [
"1. ①のごみ箱を取外しCUSHION で梱包する",
"2. 1完成品のｶﾞｰﾄﾞを外しCUSHION で梱包する"
],
"WorkPoints": [
"M4×8 AWを袋に入れる",
"TAPE(No.4140 幅50mm×25m透明)",
"CUSHION 350×350",
"CUSHION 1000×600",
... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ梱包3【ｽﾄｯｶｰ仕様】",
"WorkItems": [
"1. ①をCUSHION で梱包しLABEL を貼付ける"
],
"WorkPoints": [
"TAPE(No.4140 幅50mm×25m透明)",
"CUSHION 1500×1000㎜",
"CUSHION 1000×500㎜(2つ折り)",
"CUSHION 150×150㎜",
"CUSHION 150×150㎜... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲﾌｨｰﾀﾞｰﾕﾆｯﾄ梱包4【ｽﾄｯｶｰ仕様】",
"WorkItems": [
"1. ①をBAG で覆い梱包しLABEL を貼付ける"
],
"WorkPoints": [
"TAPE(No.4140 幅50mm×25m透明)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "VTSU梱包①(ｸﾞﾘｰｽ塗布)(海外出荷時のみ)",
"WorkItems": [
"1. ①のｶﾊﾞｰを外す(3箇所)",
"◆2. ﾎﾞｰﾙねじ､LMｶﾞｲﾄﾞ5本､水準器設置箇所にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"ﾘﾌﾄ部 ﾎﾞｰﾙねじ",
"ﾘﾌﾄ部 LMｶﾞｲﾄﾞ(2本)",
"引き出し部 SP軸LMｶﾞｲﾄﾞ",
"引き出し部 SP軸LMｶﾞｲﾄﾞ",
"水準... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布:ｸﾞﾘｰｽ容器各10㎜程度",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN･m",
"WorkName": "VTSU梱包②(防錆油確認)(海外出荷時のみ)",
"WorkItems": [
"2. 外したｶﾊﾞｰを取付ける(A/B/C:3箇所)"
],
"WorkPoints": [
"必要に応じ､防錆油を薄く塗布する"
],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "VTSU梱包②(防錆油確認)(海外出荷時のみ)",
"WorkItems": [
"1. ①の指定箇所に防錆油が塗布されているか確認する｡ ( ﾘﾌﾄ部ﾌﾚｰﾑ / 連結部ﾌﾞﾛｯｸ )",
"2. 外したｶﾊﾞｰを取付ける(A/B/C:3箇所)"
],
"WorkPoints": [
"必要に応じ､防錆油を薄く塗布する",
"連結部 ﾌﾞﾛｯｸ",
"ﾘﾌﾄ部 ﾌﾚｰﾑ"
],
"Tolks": [
... | {
"QualityItem": "塗布確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "VTSU梱包③(輸送用固定ﾌﾞﾗｹｯﾄ取付け-1)",
"WorkItems": [
"3. ⑤に2.完成品をBOLT で取付ける"
],
"WorkPoints": [
"先にﾌﾚｰﾑ側のﾎﾞﾙﾄを締結その後BRACKET とBRACKET を固定しているﾎﾞﾙﾄを締結"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"Inspec... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "VTSU梱包④(輸送用固定ﾌﾞﾗｹｯﾄ取付け-2)",
"WorkItems": [
"2. SS軸を矢印方向に動かし､ﾌﾞﾗｹｯﾄの穴位置と合わせBOLT で固定する"
],
"WorkPoints": [
"SS軸"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkT... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "VTSU梱包⑤(輸送用固定ﾌﾞﾗｹｯﾄ取付け-3)",
"WorkItems": [
"2. ﾏｶﾞｼﾞﾝﾄﾞｱA･Bを開ける",
"3. ①に1完成品をBOLT で固定する"
],
"WorkPoints": [
"ﾏｶﾞｼﾞﾝﾄﾞｱA",
"ﾏｶﾞｼﾞﾝﾄﾞｱB",
"ﾏｶﾞｼﾞﾝﾄﾞｱA･B両方に取付ける",
"1の完成品"
],
"Tolks": [
"締付... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "VTSU梱包⑥(連結用ﾌﾞﾗｹｯﾄ取り外し)",
"WorkItems": [
"1. ①に付いている連結用ﾌﾞﾗｹｯﾄを取り外す(2箇所)",
"2. 外したﾌﾞﾗｹｯﾄ､ﾎﾞﾙﾄ､ﾜｯｼｬｰをCUSHION TAPE を使い梱包する"
],
"WorkPoints": [
"700mm×400mm:1枚",
"ﾛｰﾚｯﾄを取り外す",
"本体連結用ﾎﾞﾙﾄM8×16､M8厚肉 各2個",
"ﾎﾞﾙﾄM5×12... | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業が出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "VTSU梱包⑦(ｱｲﾎﾞﾙﾄ取付け)",
"WorkItems": [
"1. ①にBOLT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "VTSU梱包⑧(ｴｱｰﾏｯﾄ保護-1)",
"WorkItems": [
"1. 下図を参照し①をCUSHION TAPE を使い保護する"
],
"WorkPoints": [
"配線とｴｱｰﾁｭｰﾌﾞを保護する",
"ﾌﾞﾗｹｯﾄに固定する",
"開口部を保護する",
"ｻｰｷｯﾄﾌﾟﾛﾃｸﾀ部を保護する",
"連結部を保護する",
"非常停止SWを保護する",
"280mm×200mm:... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "VTSU梱包⑨(ｴｱｰﾏｯﾄ保護-2)",
"WorkItems": [
"1. 下図を参照し①をCUSHION TAPE を使い保護する"
],
"WorkPoints": [
"ﾏｶﾞｼﾞﾝﾄﾞｱSWを保護する",
"100mm×100mm:2枚",
"ﾏｶﾞｼﾞﾝﾄﾞｱをﾃｰﾌﾟで固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "VTSU梱包⑩(外観を静電ｼｰﾄで覆い注意ﾗﾍﾞﾙ貼付け)",
"WorkItems": [
"1. ①をBAG で覆い､TAPE で固定後､LABEL を貼付ける"
],
"WorkPoints": [
"静電ｼｰﾄが裏返しになってい無い事を文字を見て確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Wo... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "標準同搬物梱包1",
"WorkItems": [
"1. 付属品のﾍﾞﾙﾄを長さ毎に小袋に入れる",
"2. 左図のようにｹｰｽの―の箇所に仕切り板を入れる",
"3. 付属品①~⑤を収納する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "標準同搬物梱包2",
"WorkItems": [
"1. 左図のように梱包箱の組立を行う",
"2. 標準同搬物ｹｰｽ 保守作業注意札を箱に収納する",
"3. 左図のように付属品を梱包する",
"4. 3にて梱包したものを収納し､ 付属品確認ﾘｽﾄをﾁｪｯｸする",
"5. 付属品ﾘｽﾄは､現物有無確認後､検査書関係と 一緒にし電子化とする"
],
"WorkPoints": [
"注)ﾘｻｲｸﾙﾏｰｸ... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LCRﾁｪｯｶｰ同搬物梱包",
"WorkItems": [
"1. CASE にCONNECTOR を置いてTAPE にて貼付ける",
"2. 梱包箱に1.完成品を収める",
"3.LCR校正証明書/検査成績書も同搬物ﾀﾞﾝﾎﾞｰﾙへ"
],
"WorkPoints": [
"CONNECTOR は仕様により枚数が異なります",
"梱包箱",
"※出荷明細参照のこと",
"LCR MEASUREMEN... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷書類貼付",
"WorkItems": [
"1. ﾋﾞﾆｰﾙ袋に書類を入れる",
"2. ALL SYSTEM内ﾀﾞﾝﾎﾞｰﾙに書類を入れる",
"3. ALL SYSTEM箱側面にﾋﾞﾆｰﾙ袋を貼る",
"4. ﾋﾞﾆｰﾙ袋内に右記載の書類を入れる"
],
"WorkPoints": [
"先頭機は右記載の書類を入れる",
"完了書設備ﾚｲｱｳﾄ表据付確認書(日･英･中)据付結果連絡書(着荷)立会議事録"... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "交換台車切替ﾕﾆｯﾄ①",
"WorkItems": [
"1. 下図の様に最終梱包する",
"2. ﾊﾟｰﾂｹｰｽをCUSHION とTAPE で梱包する"
],
"WorkPoints": [
"注)倉庫行き梱包時は上図の様にﾕﾆｯﾄにｼﾘｱﾙ№を添付する",
"注)ﾊﾟｰﾂｹｰｽをTAPE で輸送時落下しないように固定すること"
],
"Tolks": [],
"InspectionNo": "",
"... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "交換台車切替ﾕﾆｯﾄ②",
"WorkItems": [
"1. 下図の様に最終梱包する",
"2. ﾊﾟｰﾂｹｰｽをCUSHION とTAPE で梱包する"
],
"WorkPoints": [
"注)倉庫行き梱包時は上図の様にﾕﾆｯﾄにｼﾘｱﾙ№を添付する",
"注)ﾊﾟｰﾂｹｰｽをTAPE で輸送時落下しないように固定すること"
],
"Tolks": [],
"InspectionNo": "",
"... | {
"QualityItem": "梱包確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.