input stringclasses 1
value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾍｷｻﾛT20",
"ToolOther": "1.0N･m",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑦",
"WorkItems": [
"2. BRACKET にSWITCH をNUT-PLATE BOLT WASHER WASHER で取付",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": ""... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑧",
"WorkItems": [
"1. ①に②をBOLT ･WASHER で取付"
],
"WorkPoints": [
"取っ手取付用穴"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×2",
"内側面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑨",
"WorkItems": [
"1. ①にCATCH をBOLT で取付",
"2. ①にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"取っ手取付用穴"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑩",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "a,b,c部配管接続",
"WorkItems": [
"1. 後部ﾕﾆｯﾄ配管を接続する"
],
"WorkPoints": [
"※(ﾌﾚｰﾑより)とある配管は圧力制御用ｴｱｰでﾌﾚｰﾑに配管されている",
"供給部の選択により接続がある場合はｼﾞｮｲﾝﾄにあるﾌﾟﾗｸﾞを取り外し接続します(廃棄)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "f部配管接続",
"WorkItems": [
"1. 上流仮置き配管を接続する"
],
"WorkPoints": [
"ｵﾌﾟｼｮﾝ追加により接続がある場合はｼﾞｮｲﾝﾄにあるﾌﾟﾗｸﾞを取り外し接続します(廃棄)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"f部",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "e,d部配管接続",
"WorkItems": [
"1. 前部ﾕﾆｯﾄ配管を接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"e部",
"ﾃｰﾌﾞﾙ(A1)",
"ﾃｰﾌﾞﾙ(A2)",
"d部",
"e部",... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "i,h部配管接続",
"WorkItems": [
"1. 前部ﾕﾆｯﾄ配管を接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"i部",
"ﾃｰﾌﾞﾙ(M1)",
"j部",
"i部",
"h部",
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾏｸﾞﾈｯﾄ取付け",
"WorkItems": [
"1. ﾊｰﾈｽﾎﾞｰﾄﾞにﾏｸﾞﾈｯﾄを取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"⇒ﾏｸﾞﾈｯﾄ中",
"⇒ﾏｸﾞﾈｯﾄ大"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊｰﾈｽ準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.下記ﾘｽﾄの順番でｹｰﾌﾞﾙを準備する"
]
} | {
"QualityItem": "ｹｰﾌﾞﾙの準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "付属品準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.下記ﾘｽﾄで付属品を準備する"
]
} | {
"QualityItem": "ｹｰﾌﾞﾙの準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"D-X2102",
"CN5K3012",
"CN1K3007",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN15K009/CN5K009",
"ICTR11P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回3",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN13K009",
"ICTR10P",
"CN16K010",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回4",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN3K3100",
"ACF7R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回5",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN3K3101/CN4K3101",
"MMU7R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回6",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN11K009P",
"CN11K009",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回7",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1TB1K012/2TB1K012",
"ACF15R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回8",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"3TB1K012/4TB1K012",
"ACF16R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回9",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CH1A002",
"ACF5R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回10",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CH2A002",
"ACF6R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回11",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN9K005",
"R30525R",
"R30526R",
"R30527R",
"1. CABLE を... | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回12",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"D-X2102",
"CN1K3009",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回13",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN10K007",
"CX2112",
"1G10740R",
"1G10730R",
"1. CABLE... | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回14",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"MMU8R",
"ICTR12P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回15",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"F-X2101",
"CN2K3100",
"CN1K3101",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回16",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"C-X2102",
"CN1K3132",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回17",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN4K3100",
"ICTR3R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回18",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B-X2101",
"CN1K3131",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ｲﾝｼｭﾛｯｸ固定",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. ｲﾝｼｭﾛｯｸで固定する",
"⇒100mm",
"⇒150mm",
"⇒200mm",
"⇒250m... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台上面中継JOINT組付け①",
"WorkItems": [
"1. PLATE にJOINT を取付",
"2. PLATE にJOINT GROMMET を取付",
"3. PLATE にJOINT GROMMET を取付"
],
"WorkPoints": [
"3個製作(g:j:l用)",
"1個製作(n用)",
"1個製作(m用)"
],
"Tolks": [],
"Inspect... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台上面中継JOINT組付け②(g部)",
"WorkItems": [
"1. ①にJOINT ･JOINT を取付",
"2. 1.完成品にJOINT ･JOINT ･JOINT を取付",
"3. 2.完成品にﾏｽｷﾝｸﾞﾃｰﾌﾟでﾎﾟｼﾞｼｮﾝ名称を記入",
"4. 3.完成品にBOLT ･WASHER を添付"
],
"WorkPoints": [
"取付け方向に注意! この部品には方向性があります",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台上面中継JOINT組付け③(j部)",
"WorkItems": [
"1. ①にJOINT JOINT JOINT を取付",
"2. 1.完成品にJOINT JOINT JOINT JOINT JOINT JOINT を取付ける",
"3. 2.完成品にﾏｽｷﾝｸﾞﾃｰﾌﾟでﾎﾟｼﾞｼｮﾝ名称を記入する",
"4. 3.完成品にBOLT WASHER を添付"
],
"WorkPoints": [
"取付け方向に注... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台上面中継JOINT組付け④(n部)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台上面中継JOINT組付け⑤(l部)",
"WorkItems": [
"1. ①にJOINT ･JOINT を取付",
"2. 1.完成品にJOINT ･JOINT ･JOINT ･JOINT を取付",
"3. 2.完成品にﾏｽｷﾝｸﾞﾃｰﾌﾟでﾎﾟｼﾞｼｮﾝ名称を記入する",
"4. 3.完成品にBOLT ･WASHER を添付"
],
"WorkPoints": [
"取付け方向に注意! この部品には方向性があり... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台上面中継JOINT組付け⑥(m部)",
"WorkItems": [
"1. ①にJOINT を取付",
"2. 1.完成品にJOINT JOINT を取付",
"3. 2.完成品にﾏｽｷﾝｸﾞﾃｰﾌﾟでﾎﾟｼﾞｼｮﾝ名称を記入する",
"4. 3.完成品にBOLT WASHER を添付"
],
"WorkPoints": [
"取付け方向に注意! この部品には方向性があります"
],
"Tolks": [... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "架台上面中継JOINT配管(g部:j部)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "架台上面中継JOINT配管(n部:l部:m部)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3.5m",
"ToolOther": "",
"WorkName": "配管準備①(正圧系)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3.5m",
"ToolOther": "",
"WorkName": "配管準備②(真空系)",
"WorkItems": [
"2. TUBE でｶｯﾄした配管をJOINT ･JOINT ･JOINT ･JOINT ･JOINT に挿入",
"1. TUBE ･TUBE を指定の長さでｶｯﾄ"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3.5m",
"ToolOther": "",
"WorkName": "配管準備③(排気系)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3.5m",
"ToolOther": "",
"WorkName": "ｴｷｿﾞｰｽﾄﾌｨﾙﾀｰ組立",
"WorkItems": [
"1. EXHAUST-CLEANER にJOINT を取付",
"2. 1.完成品にEXHAUST-CLEANER 付属品を取付",
"3. TUBE を指定の長さにｶｯﾄ",
"4. 2.完成品にTUBE の配管を接続",
"5. 4.完成品にBOLT ･WASHER を付属する"
],
"WorkPoints": [],
"To... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:750㎜±5㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ｶﾊﾞｰﾛｯｸﾊﾞﾙﾌﾞ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:250㎜±5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ｲｵﾅｲｻﾞｰﾊﾞﾙﾌﾞ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾞﾛﾒｯﾄ前準備",
"WorkItems": [
"1. GROMMET に切り込みを入れる",
"2. 次工程(本体)へ払い出す"
],
"WorkPoints": [
"ｸﾞﾛﾒｯﾄ4個共に切れ込みを入れる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りの寸法で取付いていること指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "5.3N･m",
"WorkName": "部品廃棄BOX前段取り①",
"WorkItems": [
"1. ROD にSCREW を取付ける"
],
"WorkPoints": [
"SCREW がROD の底付きするところまで締める"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.3N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "5.5㎜",
"ToolOther": "40cN･m",
"WorkName": "部品廃棄BOX前段取り②",
"WorkItems": [
"1. BOX にBOLT とNUT を取付ける",
"2. 1完成品にSHEET を取付ける"
],
"WorkPoints": [
"NUTの方向に注意",
"上方向に押し当てる",
"SHEET C2面取り4箇所確認のこと",
"2個製作"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "40cN･m",
"WorkName": "部品廃棄BOX前段取り③",
"WorkItems": [
"2. BRACKET にSENSOR をBOLT WASHER WASHER で取付",
"1. BRACKET に⑥を貼付"
],
"WorkPoints": [
"ｾﾝｻのｺﾈｸﾀ挿入口(白色)がﾌﾞﾗｹｯﾄの折り曲げ方向"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "部品廃棄BOX前段取り③",
"WorkItems": [],
"WorkPoints": [
"BRACKET の貼付ける箇所をｱﾙｺｰﾙにて清掃"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"20mm",
"20mm"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に取付けてある事指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "5.3N･m",
"WorkName": "ﾁｪﾝｼﾞｬｰ前段取り①",
"WorkItems": [],
"WorkPoints": [
"6個製作",
"SCREW がPOST の底付きするところまで締める"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.3N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾁｪﾝｼﾞｬｰ前段取り①",
"WorkItems": [
"4. 2完成品にBUSH を取付､JOINT を⑯⑰で取付ける",
"3. BUSH を指定の長さに切る",
"2. BRACKET にLABEL を貼付ける",
"1. POST にSCREW を取付ける"
],
"WorkPoints": [
"16mmを2個作成",
"切り欠きから端面まで短い方にSCREW を取付ける",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に取付けてある事指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ﾁｪﾝｼﾞｬｰ前段取り①",
"WorkItems": [
"4. 2完成品にBUSH を取付､JOINT を⑯⑰で取付ける",
"3. BUSH を指定の長さに切る"
],
"WorkPoints": [
"16mmを2個作成"
],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開口部ｾﾝｻｰ組立1",
"WorkItems": [
"■1. SENSOR の型式を確認し､ﾛｯﾄNoを検査書に記入",
"2. BRACKET に⑥LABEL を貼付",
"3. 2完成品にSENSOR をBOLT WASHER で取付"
],
"WorkPoints": [
"各2個製作",
"ｾﾝｻ取付け前に検査表記入の事",
"型式",
"ﾛｯﾄ№(製造番号)",
"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に取付けてある事指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "開口部ｾﾝｻｰ組立1",
"WorkItems": [
"3. 2完成品にSENSOR をBOLT WASHER で取付"
],
"WorkPoints": [
"投光側･受光側の取付に注意",
"3芯",
"4芯",
"投光側B1046TB1047T",
"受光側B1046B1047",
"ﾌﾞﾗｹｯﾄより7㎜位置で取付"
],
"Tolks": [
... | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開口部ｾﾝｻｰ組立1",
"WorkItems": [
"■1. SENSOR の型式を確認し､ﾛｯﾄNoを検査書に記入",
"3. 2完成品にSENSOR をBOLT WASHER で取付",
"2. BRACKET に⑥LABEL を貼付"
],
"WorkPoints": [
"投光側･受光側の取付に注意",
"各2個製作",
"ｾﾝｻ取付け前に検査表記入の事",
"3芯",
"4芯",... | {
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開口部ｾﾝｻ組立2",
"WorkItems": [
"1. ①に⑥を取付",
"2. ①の完成品のｹｰﾌﾞﾙを㉗でブラケットに固定"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄ端面から50㎜で結束",
"F用",
"R用",
"投光(3芯)",
"受光(4芯)",
"被服端面に合わせてﾏｰｷﾝｸﾞﾀｲを取付"
],
"Tolks": [],
"Ins... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:端面より5㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開口部ｾﾝｻ束線",
"WorkItems": [
"1. ①の配線に印をする",
"2. 配線を輪にまとめ㉗で縛る"
],
"WorkPoints": [
"ｲﾝｼｭﾛｯｸ端から85mm",
"ｺﾈｸﾀ端から75mm",
"印が合う位置で輪を3つ作る",
"印の位置で㉗で縛る",
"･3つの輪の大きさを合わせる･印の位置がずれないように注意"
],
"Tolks": [],
... | {
"QualityItem": "配線･配管干渉確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｲﾝｼｭﾛｯｸ端から85㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開口部ｾﾝｻ束線",
"WorkItems": [
"1. ①の配線に印をする",
"2. 配線を輪にまとめ㉗で縛る"
],
"WorkPoints": [
"ｲﾝｼｭﾛｯｸ端から85mm",
"ｺﾈｸﾀ端から75mm",
"印が合う位置で輪を3つ作る",
"印の位置で㉗で縛る",
"･3つの輪の大きさを合わせる･印の位置がずれないように注意"
],
"Tolks": [],
... | {
"QualityItem": "配線･配管干渉確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｺﾈｸﾀ端から85㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "12㎜",
"ToolOther": "5.3N･m",
"WorkName": "熱補正ﾎﾟｰﾙ組立1",
"WorkItems": [],
"WorkPoints": [
"防錆油を忘れずに塗布しておくこと",
"2SET製作"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m",
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"W... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各5.3N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "5.3N･m",
"WorkName": "熱補正ﾎﾟｰﾙ組立1",
"WorkItems": [
"1. SHAFT にSCREW を締め込む(6本)",
"2. 1の完成品をBAR に取付ける"
],
"WorkPoints": [
"SCREW がSHAFT の底付きするところまで締める",
"6ｹ製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各5.3N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "接着剤ｽｰﾊﾟｰX",
"WorkName": "熱補正ﾎﾟｰﾙ組立2",
"WorkItems": [],
"WorkPoints": [
"取付け後24Hは硬化させる事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:各1",
"▲特殊作業"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "熱補正ﾌﾟﾚｰﾄ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5981",
"WorkName": "熱補正ﾎﾟｰﾙ組立2",
"WorkItems": [],
"WorkPoints": [
"2ｾｯﾄ制作",
"2ｾｯﾄ制作"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words"... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5981",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "熱補正ﾎﾟｰﾙ組立2",
"WorkItems": [],
"WorkPoints": [
"2ｾｯﾄ制作"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"▲特殊作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "50cN･m",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ左側組立1",
"WorkItems": [
"2. SENSOR(600MM) をBRACKET にSENSOR(600MM) SCREW WASHER WASHER で取付ける",
"3. SENSOR(600MM) をBRACKET にSENSOR(600MM) SCREW WASHER WASHER で取付ける",
"■1. 型式を確認し､ﾛｯﾄNo.･ｼﾘｱﾙNo.を記入する",
... | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ左側組立1",
"WorkItems": [
"2. SENSOR(600MM) をBRACKET にSENSOR(600MM) SCREW WASHER WASHER で取付ける",
"3. SENSOR(600MM) をBRACKET にSENSOR(600MM) SCREW WASHER WASHER で取付ける",
"■1. 型式を確認し､ﾛｯﾄNo.･ｼﾘｱﾙNo.を記入する"
],
"WorkPoints": [... | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認･ﾛｯﾄ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C16",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "80cN･m",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ左側組立2",
"WorkItems": [
"1. ①をPLATE にSCREW で取付ける",
"2. 1完成品ｺﾈｸﾀｰに⑥を取付ける",
"■3. ﾛｯﾄNo.･ｼﾘｱﾙNo.を記入する"
],
"WorkPoints": [
"防錆油を塗布すること(全体)",
"F/R それぞれ1台 計2台作成",
"ｾﾝｻｰ部に防錆油が付着した場合は拭取ること... | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ左側組立2",
"WorkItems": [
"1. ①をPLATE にSCREW で取付ける",
"2. 1完成品ｺﾈｸﾀｰに⑥を取付ける",
"■3. ﾛｯﾄNo.･ｼﾘｱﾙNo.を記入する"
],
"WorkPoints": [
"防錆油を塗布すること(全体)",
"F/R それぞれ1台 計2台作成",
"ｾﾝｻｰ部に防錆油が付着した場合は拭取ること",
"ｾﾝｻ:C",
... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾛｯﾄ、ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C16",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "50cN･m",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ右側組立1",
"WorkItems": [
"3. SENSOR(600MM) をPLATE にSENSOR(600MM) SCREW WASHER WASHER で取付ける",
"2. SENSOR(600MM) をPLATE にSENSOR(600MM) SCREW WASHER WASHER で取付ける",
"■1. 型式を確認し､ﾛｯﾄNo.･ｼﾘｱﾙNo.を記入する",
"3.... | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ右側組立1",
"WorkItems": [
"3. SENSOR(600MM) をPLATE にSENSOR(600MM) SCREW WASHER WASHER で取付ける",
"2. SENSOR(600MM) をPLATE にSENSOR(600MM) SCREW WASHER WASHER で取付ける",
"■1. 型式を確認し､ﾛｯﾄNo.･ｼﾘｱﾙNo.を記入する"
],
"WorkPoints": [
... | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認･ﾛｯﾄ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C16",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ右側組立2",
"WorkItems": [
"2. ①へBRACKET をBOLT WASHER で仮取付けする",
"1. BRACKET をPLATE にBOLT WASHER で取付ける"
],
"WorkPoints": [
"取付け方向に注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionN... | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ右側組立3",
"WorkItems": [
"1. ①に⑥を取付ける",
"■2. ﾛｯﾄNo.･ｼﾘｱﾙNo.を記入する"
],
"WorkPoints": [
"被覆端面に合わせてﾗﾍﾞﾙを取付ける",
"取付け例",
"2台作成",
"ﾛｯﾄNo.",
"ｼﾘｱﾙNo."
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C... | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾛｯﾄ、ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C16",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌｨｰﾀﾞｰｾﾝｻ位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6153",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ調整1",
"WorkItems": [
"1. ①②を治具に取付ける"
],
"WorkPoints": [
"ｺﾈｸﾀｰﾗﾍﾞﾙを確認し各ｽﾃｰｼﾞの組合せを間違わない様取付けの事",
"この作業については､ｾﾝｻｰA･B･C･Dの順で順次調整を行い締結を行う事※ｾﾝｻｰ間のｽｷﾏが小さくﾄﾙｸﾄﾞﾗｲﾊﾞｰか入らない為",
"･実際のﾏｼﾝ取付穴｡･治具に使用して... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6153",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2375",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ調整1",
"WorkItems": [
"1. ①②を治具に取付ける"
],
"WorkPoints": [
"ｺﾈｸﾀｰﾗﾍﾞﾙを確認し各ｽﾃｰｼﾞの組合せを間違わない様取付けの事",
"この作業については､ｾﾝｻｰA･B･C･Dの順で順次調整を行い締結を行う事※ｾﾝｻｰ間のｽｷﾏが小さくﾄﾙｸﾄﾞﾗｲﾊﾞｰか入らない為",
"･実際のﾏｼﾝ取付穴｡･治具に使用しての取付穴 は異なるに... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2375",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌｨｰﾀﾞｰｾﾝｻ位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6153",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ調整2",
"WorkItems": [
"■1. ①と②の投光光軸が受光ｾﾝｻの中央になる様調整する",
"2. ①の残りのｾﾝｻ･ｷｯﾄを同様の手順で調整固定する"
],
"WorkPoints": [
"ﾋﾞｰﾑ光量が治具穴で絞られ無い様に光軸を調整",
"全ての対のｾﾝｻｰを調整する",
"調整後は､治具から取り外し対のｾﾝｻｰを一つにまとめておく",... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6153",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C16",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ調整2",
"WorkItems": [
"■1. ①と②の投光光軸が受光ｾﾝｻの中央になる様調整する",
"2. ①の残りのｾﾝｻ･ｷｯﾄを同様の手順で調整固定する"
],
"WorkPoints": [
"ﾋﾞｰﾑ光量が治具穴で絞られ無い様に光軸を調整",
"全ての対のｾﾝｻｰを調整する",
"調整後は､治具から取り外し対のｾﾝｻｰを一つにまとめておく",
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2375",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ調整2",
"WorkItems": [
"■1. ①と②の投光光軸が受光ｾﾝｻの中央になる様調整する",
"2. ①の残りのｾﾝｻ･ｷｯﾄを同様の手順で調整固定する"
],
"WorkPoints": [
"ﾋﾞｰﾑ光量が治具穴で絞られ無い様に光軸を調整",
"全ての対のｾﾝｻｰを調整する",
"調整後は､治具から取り外し対のｾﾝｻｰを一つにまとめておく",
"【厳守... | {
"QualityItem": "光軸確認",
"ToolManageNo": "FM-2375",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｻﾞｸﾞﾘφ5からﾋﾞｰﾑがはみ出さないこと",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C16",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃｰﾌﾟ浮きｾﾝｻ束線ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6127",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ配線固定",
"WorkItems": [
"1. ①②を㉗で固定する"
],
"WorkPoints": [
"ﾌﾛﾝﾄ､ﾘｱ､各2個ｾｯﾄ製作",
"緑で指示の㉖の頭は図のように円外側、奥側に向ける事",
"緑で指示の㉖の頭は図のように円外側、奥側に向ける事"
],
"Tolks": [],
"InspectionNo": "",
"Inspec... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6127",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板・警告ﾗﾍﾞﾙ貼付①",
"WorkItems": [
"1. COVER へ⑥を貼付ける"
],
"WorkPoints": [
"⑥を貼付ける前に㉖で脱脂の事",
"指示寸法±1mmで貼付けの事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"20... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板・警告ﾗﾍﾞﾙ貼付②",
"WorkItems": [
"1. BRACKET BRACKET へLABEL を貼付ける"
],
"WorkPoints": [
"LABEL を貼付ける前に㉖で脱脂の事",
"指示寸法±1mmで貼付けの事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品準備1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りの部材が準備出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立①",
"WorkItems": [
"1. PLATE にBOLT を取付(4箇所)"
],
"WorkPoints": [
"A側から見て左側に面取りがくる事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立②",
"WorkItems": [
"1. ①にSPACER を取付",
"2. 1完成品にPLATE を取付"
],
"WorkPoints": [
"表裏があるので注意M3ﾀｯﾌﾟの位置で確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"こ... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立③",
"WorkItems": [
"2. 1完成品にｽﾌﾟﾘﾝｸﾞ挿入",
"◆1. ①とSPRING にｸﾞﾘｰｽ塗布",
"3. NUT で締結する"
],
"WorkPoints": [
"⑤の出代:20㎜",
"ｽﾌﾟﾘﾝｸﾞの両端面に塗布すること",
"①のｼｬﾌﾄ部分に塗布"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m"
],
"In... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "BOX12㎜",
"ToolOther": "20N･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立③",
"WorkItems": [],
"WorkPoints": [
"ｽﾌﾟﾘﾝｸﾞの両端面に塗布すること"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布:小豆1",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞﾛｱｺﾈｸﾀ組立治具",
"Size": "",
"ToolOther": "FM-2324",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立③",
"WorkItems": [],
"WorkPoints": [
"ｽﾌﾟﾘﾝｸﾞの両端面に塗布すること"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｸﾞﾘｰｽ塗布:小豆1",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2324",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞﾛｱｺﾈｸﾀ位置調整治具(本体側):NPM",
"Size": "",
"ToolOther": "FM-2130",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立④",
"WorkItems": [
"1. ㉖にCOUPLER を差込む",
"2. ③を治具に取付､BOLT で締結"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立④",
"WorkItems": [
"1. ㉖にCOUPLER を差込む",
"3. 2完成品にJOINT を取付",
"2. ③を治具に取付､BOLT で締結"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 4N･m"
],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "4N･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立④",
"WorkItems": [
"3. 2完成品にJOINT を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 4N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"Cﾘ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "4N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞﾛｱｺﾈｸﾀ位置調整治具(本体側):NPM",
"Size": "",
"ToolOther": "FM-2130",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑤",
"WorkItems": [
"1. ③を㉖ごと反転させる",
"2. SPACER を左右2箇所に差込む",
"3. BOLT で左右2箇所を締結"
],
"WorkPoints": [
"ﾏｰｷﾝｸﾞは治具を外して実施する事"
],
"Tolks": [],
"InspectionNo": "",
"Inspection... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑤",
"WorkItems": [
"1. ③を㉖ごと反転させる",
"2. SPACER を左右2箇所に差込む",
"3. BOLT で左右2箇所を締結"
],
"WorkPoints": [
"⑤の出代:20㎜",
"左右2箇所",
"左右2箇所",
"ﾏｰｷﾝｸﾞは治具を外して実施する事"
],
"Tolks": [
"締付ﾄﾙｸ 10... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞﾛｱｺﾈｸﾀ位置調整治具(本体側):NPM",
"Size": "",
"ToolOther": "FM-2130",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑥",
"WorkItems": [
"1. ①を反転させて､治具を取り外す"
],
"WorkPoints": [
"治具取り外し"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"反転",
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑥",
"WorkItems": [
"2. PLATE を挿入し裏からBOLT で締結"
],
"WorkPoints": [
"⑤の出代:20㎜",
"ﾌﾟﾚｰﾄの傾きは目視で真っすぐ合わせる",
"裏側よりBOLT で各2箇所締結"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": ""... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑦",
"WorkItems": [
"1. TUBE に㉘で30ｍｍ切り目を入れる",
"2. ②に1完成品を被せる(4箇所)",
"3. ｲﾝｼｭﾛｯｸで固定(4箇所)",
"1. TUBE に㉘で30ｍｍ切り目を入れる",
"2. ②に1完成品を被せる(4箇所)",
"3. ｲﾝｼｭﾛｯｸで固定(4箇所)"
],
"WorkPoints": [],
"Tolks": ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品準備2",
"WorkItems": [
"1. SPACER を次工程に払い出し"
],
"WorkPoints": [
"⑤の出代:20㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"Cﾘﾝｸﾞ",
"Cﾘﾝｸﾞ"
]
} | {
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りの部材が準備出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷③",
"WorkItems": [
"1. ①から部品ﾄﾚｲを取外し､CUSHION に梱包する",
"2. BLOCK SHEET をBAG の袋に入れ､1の完成品のｴｱｰﾏｯﾄにﾃｰﾌﾟで貼付､PACKING-MATERIAL に収納し､PACKING-MATERIAL をﾃｰﾌﾟで固定"
],
"WorkPoints": [
"CUSHION を㉖で止める",
"PACKING-MATERIAL の半分をﾃｰﾌﾟで止めた... | {
"QualityItem": "付属品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り収納出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷③",
"WorkItems": [
"1. ①から部品ﾄﾚｲを取外し､CUSHION に梱包する",
"2. BLOCK SHEET をBAG の袋に入れ､1の完成品のｴｱｰﾏｯﾄにﾃｰﾌﾟで貼付､PACKING-MATERIAL に収納し､PACKING-MATERIAL をﾃｰﾌﾟで固定"
],
"WorkPoints": [
"CUSHION を㉖で止める",
"PACKING-MATERIAL の半分をﾃｰﾌﾟで止めた... | {
"QualityItem": "付属品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り収納出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷①",
"WorkItems": [
"◆1. 指定箇所に防錆処理を行う"
],
"WorkPoints": [
"X,Y,Z軸のﾘﾆｱにｸﾞﾘｰｽ塗布",
"X軸:左右に移動させて塗布",
"Y軸:前後に移動させて塗布",
"Z軸:上下に移動させて塗布",
"上下ﾘﾆｱ",
"ﾎﾞｰﾙﾈｼﾞ",
"ｸﾞﾘｰｽ塗布は海外出荷時のみ対応の事(国内不要)"
],
"Tolks": ... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "出荷②",
"WorkItems": [
"1. ①にBRACKET をBOLT BOLT で取付",
"2. 1.完成品にLABEL とLABEL or LABEL を貼付ける"
],
"WorkPoints": [
"X,Y,Z軸はBRACKET を取付出来る位置に移動させ取付を行う事",
"BRACKET の取付位置に注意(図参照)",
"貼付箇所㉚で拭き取り貼付ける事",
"寸法や方向に注意し... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "出荷②",
"WorkItems": [
"1. ①にBRACKET をBOLT BOLT で取付"
],
"WorkPoints": [
"X,Y,Z軸はBRACKET を取付出来る位置に移動させ取付を行う事",
"BRACKET の取付位置に注意(図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"I... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "出荷②",
"WorkItems": [
"2. 1.完成品にLABEL とLABEL or LABEL を貼付ける"
],
"WorkPoints": [
"貼付箇所㉚で拭き取り貼付ける事",
"寸法や方向に注意して貼付ける事",
"LABEL 本標識は中国への出荷機のみに貼付ける事",
"LABEL 本標識は英国への出荷機のみに貼付ける事"
],
"Tolks": [],
"Inspe... | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.