input stringclasses 1 value | instruction stringlengths 222 3.65k | output stringlengths 193 367 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "HANDY-CHECKER",
"Size": "",
"ToolOther": "OMRONE39-VA",
"WorkName": "機能検査",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･ｽﾄﾛｰｸﾞ全域で最大荷重を測定する (3.5N 以下)",
"･着脱の際､引っかかりが無い事",
"検査表①: ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ着脱確認",
"ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ",
"ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ装着確認治具",
"着脱",
"3. ﾁｪﾝｼﾞｬｰの自重落下確認",
"･ﾚﾊﾞｰを押す",
"･自重落下する事",
"･ﾁｪｯｶｰが点灯 する事",
"4. 3ﾉｽﾞﾙ､ ｾｯﾄ確認",
"･ｼｬｯﾀｰ｢開｣でﾉｽﾞﾙｾｯﾄ",
"･ｼｬｯﾀｰ｢閉｣",
"･引っかかりが無くｽﾑｰｽﾞな事･ﾉｽﾞﾙに遊びがある事",
"･ｼｬｯﾀｰ｢開閉｣ｽｲｯﾁ",
"※.全15ｽﾃｰｼｮﾝにﾉｽﾞﾙ冶具をｾｯﾄして確認する事",
"検査表①: ﾉｽﾞﾙｾｯﾄ確認",
"FM-2169",
"･隙間無いこと",
"･ｽｲｯﾁ開側(上)で開ﾗﾝﾌﾟ (点灯)･ｽｲｯﾁ閉側(下)で閉ﾗﾝﾌﾟ (点灯)する事"
]
} | {
"QualityItem": "自重落下確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "自重落下時表示｢赤点灯｣",
"Method": "ﾊﾝﾃﾞｨﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾁｪﾝｼﾞｬｰ検査装置",
"Size": "",
"ToolOther": "FM-2169",
"WorkName": "機能検査",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･ｽﾄﾛｰｸﾞ全域で最大荷重を測定する (3.5N 以下)",
"･着脱の際､引っかかりが無い事",
"検査表①: ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ着脱確認",
"ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ",
"ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ装着確認治具",
"着脱",
"3. ﾁｪﾝｼﾞｬｰの自重落下確認",
"･ﾚﾊﾞｰを押す",
"･自重落下する事",
"･ﾁｪｯｶｰが点灯 する事",
"4. 3ﾉｽﾞﾙ､ ｾｯﾄ確認",
"･ｼｬｯﾀｰ｢開｣でﾉｽﾞﾙｾｯﾄ",
"･ｼｬｯﾀｰ｢閉｣",
"･引っかかりが無くｽﾑｰｽﾞな事･ﾉｽﾞﾙに遊びがある事",
"･ｼｬｯﾀｰ｢開閉｣ｽｲｯﾁ",
"※.全15ｽﾃｰｼｮﾝにﾉｽﾞﾙ冶具をｾｯﾄして確認する事",
"検査表①: ﾉｽﾞﾙｾｯﾄ確認",
"FM-2169",
"･隙間無いこと",
"･ｽｲｯﾁ開側(上)で開ﾗﾝﾌﾟ (点灯)･ｽｲｯﾁ閉側(下)で閉ﾗﾝﾌﾟ (点灯)する事",
"WCRE-E013-009"
]
} | {
"QualityItem": "ｾｯﾄ確認",
"ToolManageNo": "FM-2169",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｼｬｯﾀｰ動作ｽﾑｰｽﾞである事",
"Method": "目視",
"RecordMethod": "WCRE-E013-009",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙ冶具",
"Size": "",
"ToolOther": "",
"WorkName": "機能検査",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"･ｽﾄﾛｰｸﾞ全域で最大荷重を測定する (3.5N 以下)",
"･着脱の際､引っかかりが無い事",
"検査表①: ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ着脱確認",
"ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ",
"ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ装着確認治具",
"着脱",
"3. ﾁｪﾝｼﾞｬｰの自重落下確認",
"･ﾚﾊﾞｰを押す",
"･自重落下する事",
"･ﾁｪｯｶｰが点灯 する事",
"4. 3ﾉｽﾞﾙ､ ｾｯﾄ確認",
"･ｼｬｯﾀｰ｢開｣でﾉｽﾞﾙｾｯﾄ",
"･ｼｬｯﾀｰ｢閉｣",
"･引っかかりが無くｽﾑｰｽﾞな事･ﾉｽﾞﾙに遊びがある事",
"･ｼｬｯﾀｰ｢開閉｣ｽｲｯﾁ",
"※.全15ｽﾃｰｼｮﾝにﾉｽﾞﾙ冶具をｾｯﾄして確認する事",
"検査表①: ﾉｽﾞﾙｾｯﾄ確認",
"FM-2169",
"･隙間無いこと",
"･ｽｲｯﾁ開側(上)で開ﾗﾝﾌﾟ (点灯)･ｽｲｯﾁ閉側(下)で閉ﾗﾝﾌﾟ (点灯)する事"
]
} | {
"QualityItem": "ｾｯﾄ確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｼｬｯﾀｰ閉時ﾉｽﾞﾙに遊びがある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "右側ﾌﾟﾚｰﾄ_ﾋﾟﾝ圧入",
"WorkItems": [
"1. PLATE にPIN を圧入する",
"2. PLATE にPIN を圧入する",
"1. PLATE にPIN を圧入する",
"2. PLATE にPIN を圧入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝ圧入ｼﾞｸﾞ(φ6､6)",
"Size": "",
"ToolOther": "FM-6534",
"WorkName": "右側ﾌﾟﾚｰﾄ_ﾋﾟﾝ圧入",
"WorkItems": [
"1. PLATE にPIN を圧入する",
"2. PLATE にPIN を圧入する"
],
"WorkPoints": [
"ﾊﾞﾘ､打痕がないか確認する",
"圧入方向に注意",
"圧入方向に注意",
"全てのPINを球面側から圧入する事",
"球面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"出代:11.8mm",
"出代:6mm"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "FM-6534",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代6㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "左側ﾌﾟﾚｰﾄ_ﾋﾟﾝ圧入",
"WorkItems": [
"1. PLATE にPIN を圧入する",
"2. PLATE にPIN を圧入する",
"1. PLATE にPIN を圧入する",
"2. PLATE にPIN を圧入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝ圧入ｼﾞｸﾞ(φ6､6)",
"Size": "",
"ToolOther": "FM-6534",
"WorkName": "左側ﾌﾟﾚｰﾄ_ﾋﾟﾝ圧入",
"WorkItems": [
"1. PLATE にPIN を圧入する",
"2. PLATE にPIN を圧入する"
],
"WorkPoints": [
"ﾊﾞﾘ､打痕がないか確認する",
"圧入方向に注意",
"圧入方向に注意",
"全てのPINを球面側から圧入する事",
"球面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"出代:11.8mm",
"出代:6mm"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "FM-6534",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代6㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "CPU-BOX_ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①にBRACKET BRACKET を①付属のﾎﾞﾙﾄで固定する"
],
"WorkPoints": [
"付属のﾎﾞﾙﾄ M5×12厚肉",
"付属のﾎﾞﾙﾄ M5×12厚肉",
"矢印方向へ押し当て"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "50cN･m",
"WorkName": "ｱｳﾄﾚｯﾄｷｯﾄ組立",
"WorkItems": [
"1. BRACKET にCONNECTOR-ACCESSORIES を取付ける",
"2. BRACKET にCABLE をSCREW で取付ける",
"3. BRACKET にPLATE をSCREW で取付ける",
"4. BRACKET にCONNECTOR を取付ける",
"1. BRACKET にCONNECTOR-ACCESSORIES を取付ける",
"2. BRACKET にCABLE をSCREW で取付ける",
"3. BRACKET にPLATE をSCREW で取付ける",
"4. BRACKET にCONNECTOR を取付ける"
],
"WorkPoints": [
"ｶﾁｯと音がするまで差込む",
"ｶﾁｯと音がするまで差込む"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "90cN･m",
"WorkName": "背面ﾌﾟﾚｰﾄ_ﾎﾟｽﾄ取付",
"WorkItems": [
"1. COVER にSPACER をSCREW で取付ける",
"2. COVER にSPACER をSCREW で取付ける",
"3. COVER にSPACER をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "背面ﾌﾟﾚｰﾄ_ﾎﾟｽﾄ取付",
"WorkItems": [
"1. COVER にSPACER をSCREW で取付ける",
"2. COVER にSPACER をSCREW で取付ける",
"3. COVER にSPACER をSCREW で取付ける",
"1. COVER にSPACER をSCREW で取付ける",
"2. COVER にSPACER をSCREW で取付ける",
"3. COVER にSPACER をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面ﾌﾟﾚｰﾄ_ﾄﾘﾑ、FT4取付",
"WorkItems": [
"1. ①にCABLE-SUPPORT BUSH BUSH を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｴｯｼﾞｶﾊﾞｰ(ﾄﾘﾑ､ﾗﾍﾞﾙ)確認",
"2LC-JG-23015"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付できている事を確認する",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "50cN･m",
"WorkName": "背面ﾌﾟﾚｰﾄ_ﾘﾚｰﾎﾞｰﾄﾞ型式確認、取付",
"WorkItems": [
"2. ①にCONNECTOR RELAY BOARD:OFFLINECAMERA をSCREW で取付ける",
"■★1. CONNECTOR RELAY BOARD:OFFLINECAMERA の型式･ｼﾘｱﾙ番号を確認し､検査表へ記入する"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙ"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:型式･検査書ﾁｪｯｸ",
"★静電対策作業",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "背面ﾌﾟﾚｰﾄ_ﾘﾚｰﾎﾞｰﾄﾞ型式確認、取付",
"WorkItems": [
"2. ①にCONNECTOR RELAY BOARD:OFFLINECAMERA をSCREW で取付ける",
"■★1. CONNECTOR RELAY BOARD:OFFLINECAMERA の型式･ｼﾘｱﾙ番号を確認し､検査表へ記入する"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙ"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:型式･検査書ﾁｪｯｸ",
"2LC-JG-23015"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾘﾑ、FT4取付け",
"WorkItems": [
"1. PLATE にCABLE-SUPPORT COVER COVER COVER ⑥を取付ける"
],
"WorkPoints": [
"COVER COVER は長穴中央に貼付け",
"COVER は長穴下側寄せで取付け"
],
"Tolks": [],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表PLATE :ｴｯｼﾞｶﾊﾞｰ(ﾄﾘﾑ､ﾗﾍﾞﾙ)確認"
],
"WorkTypes": [],
"Words": [
"2LC-JG-23015"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付できている事を確認する",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "下面補強ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①にANGLE をWASHER BOLT で取付ける"
],
"WorkPoints": [
"上面"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "上面補強ﾌﾞﾗｹｯﾄ取付_右",
"WorkItems": [
"1. ANGLE にCOVER を取付ける",
"2. ①に1.完成品をWASHER BOLT BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｴｯｼﾞｶﾊﾞｰ(ﾄﾘﾑ､ﾗﾍﾞﾙ)確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上面補強ﾌﾞﾗｹｯﾄ取付_右",
"WorkItems": [
"1. ANGLE にCOVER を取付ける",
"2. ①に1.完成品をWASHER BOLT BOLT で取付ける"
],
"WorkPoints": [
"裏面",
"M5×10",
"M5×8"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:ｴｯｼﾞｶﾊﾞｰ(ﾄﾘﾑ､ﾗﾍﾞﾙ)確認"
],
"WorkTypes": [],
"Words": [
"2LC-JG-23015"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付できている事を確認する",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "上面補強ﾌﾞﾗｹｯﾄ取付_左",
"WorkItems": [
"2. ANGLE にCOVER COVER を取付ける",
"3. ①に1.完成品をBOLT BOLT WASHER で取付ける",
"1. ANGLE にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"指定の寸法で取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "上面補強ﾌﾞﾗｹｯﾄ取付_左",
"WorkItems": [
"2. ANGLE にCOVER COVER を取付ける",
"3. ①に1.完成品をBOLT BOLT WASHER で取付ける",
"1. ANGLE にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"指定の寸法で取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付できている事を確認する",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "上面補強ﾌﾞﾗｹｯﾄ取付_左",
"WorkItems": [
"2. ANGLE にCOVER COVER を取付ける",
"3. ①に1.完成品をBOLT BOLT WASHER で取付ける",
"1. ANGLE にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"指定の寸法で取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "120cN･m",
"WorkName": "DC電源取付",
"WorkItems": [
"2. ①にPOWER-SUPPLY をWASHER BOLT で取付ける",
"■1. POWER-SUPPLY の型式､ｼﾘｱﾙ番号を確認し検査表に記入する"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙ"
],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:型式･検査書ﾁｪｯｸ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DC電源取付",
"WorkItems": [
"2. ①にPOWER-SUPPLY をWASHER BOLT で取付ける",
"■1. POWER-SUPPLY の型式､ｼﾘｱﾙ番号を確認し検査表に記入する"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙ"
],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [],
"Words": [
"2LC-JG-23015"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "100cN･m",
"WorkName": "ﾌﾞﾚｰｶｰｷｯﾄ前組",
"WorkItems": [
"2. BRACKET にBREAKER をBOLT で取付ける",
"■1. BREAKER の型式､ｼﾘｱﾙ番号を確認し､検査表へ記入する"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表BRACKET :ｴｯｼﾞｶﾊﾞｰ(ﾄﾘﾑ､ﾗﾍﾞﾙ)確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾞﾚｰｶｰｷｯﾄ前組",
"WorkItems": [
"3. BRACKET にBUSH を取付ける",
"2. BRACKET にBREAKER をBOLT で取付ける",
"■1. BREAKER の型式､ｼﾘｱﾙ番号を確認し､検査表へ記入する"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙ",
"付属のｶﾊﾞｰ､ﾎﾞﾙﾄは後工程で使用するので取っておく"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表BRACKET :型式･検査書ﾁｪｯｸ",
"検査表BRACKET :ｴｯｼﾞｶﾊﾞｰ(ﾄﾘﾑ､ﾗﾍﾞﾙ)確認",
"2LC-JG-23015"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾌﾞﾚｰｶｰｷｯﾄ取付",
"WorkItems": [
"1. ②に①をWASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "100cN･m",
"WorkName": "ｻｰｼﾞｷﾗｰ取付",
"WorkItems": [
"3. ①にSERGE PROTECTOR をWASHER BOLT で取付ける",
"■1. SERGE PROTECTOR の型式､ｼﾘｱﾙ番号を確認し､検査表へ記入する"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙ"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻｰｼﾞｷﾗｰ取付",
"WorkItems": [
"2. SERGE PROTECTOR にCABLE を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:型式･検査書ﾁｪｯｸ",
"10㎜",
"■安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付できている事を確認する",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰｼﾞｷﾗｰ取付",
"WorkItems": [
"3. ①にSERGE PROTECTOR をWASHER BOLT で取付ける",
"2. SERGE PROTECTOR にCABLE を取付ける",
"■1. SERGE PROTECTOR の型式､ｼﾘｱﾙ番号を確認し､検査表へ記入する"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙ"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:型式･検査書ﾁｪｯｸ",
"10㎜",
"2LC-JG-23015"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｱｰｽﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. ①にTERMINAL をWASHER BOLT で取付ける"
],
"WorkPoints": [
"ｱｰｽﾏｰｸが手前に来るように取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾉｲｽﾞﾌｨﾙﾀｰ取付",
"WorkItems": [
"2. ①にNOISE-FILTER をWASHER BOLT で取付ける",
"■1. NOISE-FILTER の型式､ｼﾘｱﾙ番号を確認し､検査表に記入する"
],
"WorkPoints": [
"1､2がﾌﾞﾚｰｶｰ側になるように取付",
"型式",
"ｼﾘｱﾙ"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:型式･検査書ﾁｪｯｸ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾉｲｽﾞﾌｨﾙﾀｰ取付",
"WorkItems": [
"2. ①にNOISE-FILTER をWASHER BOLT で取付ける",
"■1. NOISE-FILTER の型式､ｼﾘｱﾙ番号を確認し､検査表に記入する"
],
"WorkPoints": [
"1､2がﾌﾞﾚｰｶｰ側になるように取付",
"型式",
"ｼﾘｱﾙ"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:型式･検査書ﾁｪｯｸ",
"2LC-JG-23015"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "100cN･m",
"WorkName": "ｻｰｷｯﾄﾌﾟﾛﾃｸﾀ取付",
"WorkItems": [
"2. ①にCIRCUIT-PROTECTOR をWASHER BOLT で取付ける",
"■1. CIRCUIT-PROTECTOR の型式､ｼﾘｱﾙ番号を確認し検査表に記入する"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙ"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:型式･検査書ﾁｪｯｸ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰｷｯﾄﾌﾟﾛﾃｸﾀ取付",
"WorkItems": [
"2. ①にCIRCUIT-PROTECTOR をWASHER BOLT で取付ける",
"■1. CIRCUIT-PROTECTOR の型式､ｼﾘｱﾙ番号を確認し検査表に記入する"
],
"WorkPoints": [
"型式",
"ｼﾘｱﾙ"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [],
"Words": [
"2LC-JG-23015"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ｻｰｼﾞｷﾗｰ・ﾉｲｽﾞﾌｨﾙﾀｰ配線引き回し",
"WorkItems": [
"■1. ①のｻｰｼﾞｷﾗｰのｱｰｽ線をｱｰｽﾌﾟﾚｰﾄへSCREW で接続する",
"■3. CABLE をｱｰｽﾌﾟﾚｰﾄへSCREW で接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m",
"締付ﾄﾙｸ 180cN･m",
"締付ﾄﾙｸ 140cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"■安全作業",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ"
]
} | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "140cN･m",
"WorkName": "ｻｰｼﾞｷﾗｰ・ﾉｲｽﾞﾌｨﾙﾀｰ配線引き回し",
"WorkItems": [
"■2. CABLE をﾉｲｽﾞﾌｨﾙﾀに接続する"
],
"WorkPoints": [
"5X02",
"FGV01",
"6X02"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各140cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰｼﾞｷﾗｰ・ﾉｲｽﾞﾌｨﾙﾀｰ配線引き回し",
"WorkItems": [
"■3. CABLE をｱｰｽﾌﾟﾚｰﾄへSCREW で接続する",
"■1. ①のｻｰｼﾞｷﾗｰのｱｰｽ線をｱｰｽﾌﾟﾚｰﾄへSCREW で接続する",
"■2. CABLE をﾉｲｽﾞﾌｨﾙﾀに接続する"
],
"WorkPoints": [
"5X02",
"FGV01",
"6X02"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m",
"締付ﾄﾙｸ 180cN･m",
"締付ﾄﾙｸ 140cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続できている事を確認する",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "140cN･m",
"WorkName": "ﾉｲｽﾞﾌｨﾙﾀｰ配線引き回し",
"WorkItems": [
"■2. CABLE とｻｰｼﾞｷﾗｰの配線を引き回し､ﾌﾞﾚｰｶｰへ接続する",
"■1. ①のﾉｲｽﾞﾌｨﾙﾀｰにCABLE を接続する"
],
"WorkPoints": [
"2aV01",
"1aV01",
"4aF101",
"2aF101"
],
"Tolks": [
"締付ﾄﾙｸ 140cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"■安全作業"
]
} | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各140cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "250cN･m",
"WorkName": "ﾉｲｽﾞﾌｨﾙﾀｰ配線引き回し",
"WorkItems": [],
"WorkPoints": [
"背合せで取付ける",
"二次側",
"付属ﾎﾞﾙﾄ",
"上側"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾉｲｽﾞﾌｨﾙﾀｰ配線引き回し",
"WorkItems": [
"■2. CABLE とｻｰｼﾞｷﾗｰの配線を引き回し､ﾌﾞﾚｰｶｰへ接続する",
"■1. ①のﾉｲｽﾞﾌｨﾙﾀｰにCABLE を接続する"
],
"WorkPoints": [
"2aV01",
"1aV01",
"4aF101",
"2aF101",
"背合せで取付ける",
"二次側",
"付属ﾎﾞﾙﾄ",
"上側"
],
"Tolks": [
"締付ﾄﾙｸ 140cN･m",
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続できている事を確認する",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "140cN･m",
"WorkName": "ﾉｲｽﾞﾌｨﾙﾀｰ配線引き回し",
"WorkItems": [
"■1. ①のﾉｲｽﾞﾌｨﾙﾀｰにCABLE CABLE を接続する"
],
"WorkPoints": [
"3aV01",
"4aV01",
"反対側の配線は後工程で接続するので24V電源の近くにまとめておく"
],
"Tolks": [
"締付ﾄﾙｸ 140cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"■安全作業"
]
} | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "140cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾉｲｽﾞﾌｨﾙﾀｰ配線引き回し",
"WorkItems": [
"■1. ①のﾉｲｽﾞﾌｨﾙﾀｰにCABLE CABLE を接続する"
],
"WorkPoints": [
"3aV01",
"4aV01",
"反対側の配線は後工程で接続するので24V電源の近くにまとめておく"
],
"Tolks": [
"締付ﾄﾙｸ 140cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続できている事を確認する",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "DC電源配線引き回し①",
"WorkItems": [
"■2. CABLE を引き回しDC電源へ接続する",
"■1. ①のｱｰｽﾌﾟﾚｰﾄにCABLE をSCREW で接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"■安全作業"
]
} | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "DC電源配線引き回し①",
"WorkItems": [
"■2. CABLE を引き回しDC電源へ接続する",
"■1. ①のｱｰｽﾌﾟﾚｰﾄにCABLE をSCREW で接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"■安全作業"
]
} | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DC電源配線引き回し①",
"WorkItems": [
"■2. CABLE を引き回しDC電源へ接続する",
"■1. ①のｱｰｽﾌﾟﾚｰﾄにCABLE をSCREW で接続する"
],
"WorkPoints": [
"8X02",
"E_T101"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続できている事を確認する",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "DC電源配線引き回し②",
"WorkItems": [
"■1. ①のｱｰｽﾌﾟﾚｰﾄにCABLE をSCREW で接続する"
],
"WorkPoints": [
"7X02",
"反対側の配線は後工程で接続するのでDC電源の近くにまとめておく"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"■安全作業"
]
} | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DC電源配線引き回し②",
"WorkItems": [
"■1. ①のｱｰｽﾌﾟﾚｰﾄにCABLE をSCREW で接続する"
],
"WorkPoints": [
"7X02",
"反対側の配線は後工程で接続するのでDC電源の近くにまとめておく"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続できている事を確認する",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "150cN･m",
"WorkName": "DC電源・ｻｰｷｯﾄﾌﾟﾛﾃｸﾀ配線引き回し",
"WorkItems": [],
"WorkPoints": [
"1aF102",
"3aF102",
"+V1aT101",
"-V1aT101"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"■安全作業"
]
} | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "DC電源・ｻｰｷｯﾄﾌﾟﾛﾃｸﾀ配線引き回し",
"WorkItems": [],
"WorkPoints": [
"1aF102",
"3aF102",
"+V1aT101",
"-V1aT101"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"■安全作業"
]
} | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DC電源・ｻｰｷｯﾄﾌﾟﾛﾃｸﾀ配線引き回し",
"WorkItems": [
"■2. CABLE CABLE を引き回し､DC電源に接続する",
"■1. ①のｻｰｷｯﾄﾌﾟﾛﾃｸﾀにCABLE CABLE を引き回し接続する"
],
"WorkPoints": [
"1aF102",
"3aF102",
"+V1aT101",
"-V1aT101"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:ﾈｼﾞ締めﾄﾙｸ"
],
"WorkTypes": [],
"Words": [
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続できている事を確認する",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "50cN･m",
"WorkName": "ｶﾒﾗ配線接続ｶﾊﾞｰ取付",
"WorkItems": [
"3. ①にｶﾊﾞｰを流用ﾎﾞﾙﾄで取付ける"
],
"WorkPoints": [
"作業1にて外したﾎﾞﾙﾄを流用",
"配線の挟み込みに注意",
"ｺﾈｸﾀ差込み口",
"ｺﾈｸﾀ差込み口",
"外したﾎﾞﾙﾄは流用",
"ﾏｰｸﾁｭｰﾌﾞ幅分で折り曲げ､ﾏｰｸﾁｭｰﾌﾞを固定するように共結束",
"ｶﾒﾗ向き注意:ﾌﾟﾚｰﾄ切りかけ部が手前"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗ配線接続ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①の標準ｶﾊﾞｰを取り外し",
"■2. ①にCABLE を接続し､ｲﾝｼｭﾛｯｸで固定する",
"3. ①にｶﾊﾞｰを流用ﾎﾞﾙﾄで取付ける"
],
"WorkPoints": [
"作業1にて外したﾎﾞﾙﾄを流用",
"配線の挟み込みに注意",
"ｺﾈｸﾀ差込み口",
"ｺﾈｸﾀ差込み口",
"外したﾎﾞﾙﾄは流用",
"ﾏｰｸﾁｭｰﾌﾞ幅分で折り曲げ､ﾏｰｸﾁｭｰﾌﾞを固定するように共結束",
"ｶﾒﾗ向き注意:ﾌﾟﾚｰﾄ切りかけ部が手前"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続できている事を確認する",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "部品ｽﾃｰｼﾞ取付",
"WorkItems": [
"1. ①に⑥をBOLT WASHER とBOLT で取付ける"
],
"WorkPoints": [
"⑥を各寸法に調整して取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"114㎜",
"120㎜",
"120㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "5.3N･m",
"WorkName": "部品ｽﾃｰｼﾞ取付",
"WorkItems": [
"1. ①に⑥をBOLT WASHER とBOLT で取付ける"
],
"WorkPoints": [
"⑥を各寸法に調整して取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"114㎜",
"120㎜",
"120㎜"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.3N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ｽﾃｰｼﾞ部取付",
"WorkItems": [
"2. ①にPLATE をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄPLATE を黄色点線に合わせて取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "5.3N･m",
"WorkName": "ｽﾃｰｼﾞ部取付",
"WorkItems": [
"1. ①にPLATE をBOLT とBOLT で取付ける"
],
"WorkPoints": [
"各ﾌﾟﾚｰﾄPLATE を黄色点線に合わせて取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.3N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "部品搭載ﾊﾟﾚｯﾄ平面度測定",
"WorkItems": [
"2. ㉖に①を設置する",
"1. ㉖の平面度を測定する。",
"2. ㉖に①を設置する",
"1. ㉖の平面度を測定する。"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.04㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "定盤",
"Size": "",
"ToolOther": "",
"WorkName": "部品搭載ﾊﾟﾚｯﾄ平面度測定",
"WorkItems": [
"2. ㉖に①を設置する",
"1. ㉖の平面度を測定する。",
"2. ㉖に①を設置する",
"1. ㉖の平面度を測定する。"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "平面出し治具台",
"Size": "",
"ToolOther": "",
"WorkName": "部品搭載ﾊﾟﾚｯﾄ平面度測定",
"WorkItems": [
"2. ㉖に①を設置する",
"1. ㉖の平面度を測定する。",
"2. ㉖に①を設置する",
"1. ㉖の平面度を測定する。"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "138㎜",
"ToolOther": "",
"WorkName": "部品搭載ﾊﾟﾚｯﾄ平面度測定",
"WorkItems": [
"2. ㉖に①を設置する",
"1. ㉖の平面度を測定する。"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "部品搭載ﾊﾟﾚｯﾄ平面度測定",
"WorkItems": [
"2. ㉖に①を設置する",
"1. ㉖の平面度を測定する。",
"2. ㉖に①を設置する",
"1. ㉖の平面度を測定する。"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "2LC-JG-23004",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"2LC-JG-23004"
]
} | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.2㎜以下",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "2LC-JG-23004",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "5.3N･m",
"WorkName": "ｻｲﾄﾞﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. ①に②をBOLT で取付ける",
"1. ①に②をBOLT で取付ける"
],
"WorkPoints": [
"②のﾋﾟﾝが①に押し当てられている事(2箇所)",
"④のﾋﾟﾝが①に押し当てられている事(2箇所)",
"②のﾋﾟﾝが①に押し当てられている事(2箇所)",
"④のﾋﾟﾝが①に押し当てられている事(2箇所)"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m",
"締付ﾄﾙｸ 5.3N･m",
"締付ﾄﾙｸ 5.3N･m",
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.3N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "背面ﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"配線を挟み込まないように注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｴﾝｺｰﾀﾞｰ配線の接続",
"WorkItems": [
"1. ①のｴﾝｺｰﾀﾞｰ配線を引き回し､ｺﾈｸﾀに接続する"
],
"WorkPoints": [
"CN5K302",
"CN3K302",
"CN4K302",
"照明の配線は後工程で引き回すのでまとめておく"
],
"Tolks": [
"締付ﾄﾙｸ 26cN･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:接続ﾁｪｯｸ_ｴﾝｺｰﾀﾞ中継基板"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "26cN･m",
"WorkName": "ｴﾝｺｰﾀﾞｰ配線の接続",
"WorkItems": [
"1. ①のｴﾝｺｰﾀﾞｰ配線を引き回し､ｺﾈｸﾀに接続する"
],
"WorkPoints": [
"CN5K302",
"CN3K302",
"CN4K302",
"照明の配線は後工程で引き回すのでまとめておく"
],
"Tolks": [
"締付ﾄﾙｸ 26cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:接続ﾁｪｯｸ_ｴﾝｺｰﾀﾞ中継基板"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "上面ﾌﾟﾚｰﾄ取付",
"WorkItems": [
"1. ①に②をBOLT とBOLT WASHER で取付ける"
],
"WorkPoints": [
"①のﾋﾟﾝに②を載せて取付ける事",
"①の裏面よりBOLT WASHER を取付ける事",
"①のﾋﾟﾝが②に当付けられている事"
],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "CPU-BOX取付",
"WorkItems": [
"2. ①に⑥をBOLT WASHER ､WASHER BOLT で取付ける",
"■1. ⑥の型式を確認し､ｼﾘｱﾙNoを検査表記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:型式･検査書ﾁｪｯｸ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "CPU-BOX取付",
"WorkItems": [
"2. ①に⑥をBOLT WASHER ､WASHER BOLT で取付ける",
"■1. ⑥の型式を確認し､ｼﾘｱﾙNoを検査表記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:型式･検査書ﾁｪｯｸ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPU-BOX取付",
"WorkItems": [
"2. ①に⑥をBOLT WASHER ､WASHER BOLT で取付ける",
"■1. ⑥の型式を確認し､ｼﾘｱﾙNoを検査表記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [],
"Words": [
"2LC-JG-23015"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認検査書有無確認",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "ACｲﾝﾚｯﾄ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ACｲﾝﾚｯﾄ取付",
"WorkItems": [
"2. ①にSOFTWARE-LICENSE SOFTWARE-LICENSE を貼付ける"
],
"WorkPoints": [
"AC配線は後工程で引き回すので丸めておく事"
],
"Tolks": [],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:ﾗｲｾﾝｽﾗﾍﾞﾙ貼付け確認"
],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPU-BOXAC配線引き回し1",
"WorkItems": [
"2. ACｲﾝﾚｯﾄの配線と一緒に上面ﾌﾟﾚｰﾄ側に引き回し､ｲﾝｼｭﾛｯｸで結束する",
"■1. ①にCABLE を接続する"
],
"WorkPoints": [
"1aF101と3aF101はﾌﾞﾚｰｶｰへ",
"4X02はｱｰｽﾌﾟﾚｰﾄへ",
"接続後､抜け防止でﾛｯｸする",
"AC(N)bT101とAC(L)bT101は24V電源へ",
"被覆の端面で結束する事"
],
"Tolks": [],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:CPU BOX確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "250cN･m",
"WorkName": "CPU-BOXAC配線引き回し2",
"WorkItems": [
"2. 付属のｶﾊﾞｰを取付ける",
"■1. ①のﾌﾞﾚｰｶｰに配線を接続する"
],
"WorkPoints": [
"接続間違いに注意",
"ｶﾁｯと音がするまで差込む事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ"
],
"WorkTypes": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "50cN･m",
"WorkName": "CPU-BOXAC配線引き回し2",
"WorkItems": [
"3. ①にCOVER をSCREW で取付ける"
],
"WorkPoints": [
"1aF101",
"3aF101"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "CPU-BOXAC配線引き回し3",
"WorkItems": [
"■2. ｱｰｽﾌﾟﾚｰﾄに配線をSCREW で接続する",
"■1. ①の24V電源に配線を接続する"
],
"WorkPoints": [
"背合せで取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:ﾈｼﾞ締めﾄﾙｸ"
],
"WorkTypes": [],
"Words": [
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "180cN･m",
"WorkName": "CPU-BOXAC配線引き回し3",
"WorkItems": [
"■2. ｱｰｽﾌﾟﾚｰﾄに配線をSCREW で接続する",
"■1. ①の24V電源に配線を接続する"
],
"WorkPoints": [
"背合せで取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ"
],
"WorkTypes": [],
"Words": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPU-BOXAC配線引き回し3",
"WorkItems": [
"■2. ｱｰｽﾌﾟﾚｰﾄに配線をSCREW で接続する",
"■1. ①の24V電源に配線を接続する"
],
"WorkPoints": [
"AC(N)aT101AC(N)bT101",
"4X02",
"AC(L)aT101AC(L)bT101",
"背合せで取付ける事",
"1X02"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:ﾈｼﾞ締めﾄﾙｸ"
],
"WorkTypes": [],
"Words": [
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "DC配線引き回し",
"WorkItems": [
"■1. ①の24V電源にCABLE の配線を接続する"
],
"WorkPoints": [
"背合せで取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ"
],
"WorkTypes": [],
"Words": [
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DC配線引き回し",
"WorkItems": [
"2. 配線を引き回しｺﾈｸﾀへ接続する",
"■1. ①の24V電源にCABLE の配線を接続する"
],
"WorkPoints": [
"+V2aT101",
"-V2aT101-V2bT101",
"ｶﾁｯと音がするまで差込む事",
"背合せで取付ける事",
"ここの穴から下に通す"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:ｴﾝｺｰﾀﾞ中継基板",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "MC-S取付①",
"WorkItems": [
"■1. ②の型式を確認し､ｼﾘｱﾙNoを検査書に記入する",
"◆2. ①に②をBOLT WASHER NUT で仮止めする"
],
"WorkPoints": [
"①の開口部に⑥の配線を挟み込まない様に注意する事",
"①の開口部やXYZﾃｰﾌﾞﾙに②を干渉させない様に注意して取付ける事",
"左右4箇所仮締めする事",
"本締工程:SD-A046607-515",
"二人作業"
],
"Tolks": [],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [],
"Words": [
"2LC-JG-23015"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "MC-S取付①",
"WorkItems": [
"■1. ②の型式を確認し､ｼﾘｱﾙNoを検査書に記入する",
"◆2. ①に②をBOLT WASHER NUT で仮止めする"
],
"WorkPoints": [
"①の開口部に⑥の配線を挟み込まない様に注意する事",
"①の開口部やXYZﾃｰﾌﾞﾙに②を干渉させない様に注意して取付ける事",
"左右4箇所仮締めする事",
"本締工程:SD-A046607-515",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:型式･検査書ﾁｪｯｸ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "MC-S取付②",
"WorkItems": [
"1. ①のMC-Sのﾌﾟﾚｰﾄと上面ﾌﾟﾚｰﾄの隙間を11㎜に調整し､仮締めﾎﾞﾙﾄを締結する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "11㎜",
"ToolOther": "",
"WorkName": "MC-S取付②",
"WorkItems": [
"1. ①のMC-Sのﾌﾟﾚｰﾄと上面ﾌﾟﾚｰﾄの隙間を11㎜に調整し､仮締めﾎﾞﾙﾄを締結する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "MC-S取付②",
"WorkItems": [
"2. 1完成品にCOVER を貼付ける",
"3. MC-Sからの配線を引き回し固定する"
],
"WorkPoints": [
"COVER の貼付け位置を脱脂し､右端から5㎜の位置に貼付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"11㎜",
"11㎜",
"5㎜",
"ｺﾈｸﾀｰはﾌﾞﾗｹｯﾄに挿入する"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LANｹｰﾌﾞﾙ引き回し",
"WorkItems": [
"3. ①にCABLE を引き回す",
"■1. CABLE のRoHSﾏｰｸを確認する",
"2. CABLE にNOISE-FILTER を取付ける"
],
"WorkPoints": [
"LAN1"
],
"Tolks": [],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:CPU BOX確認",
"検査表①:CPU BOX確認"
],
"WorkTypes": [],
"Words": [
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"60㎜",
"検査表①:ﾌｪﾗｲﾄｺｱ",
"2LC-JG-23015"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "RoHSﾏｰｸが貼付け出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "LANｹｰﾌﾞﾙ引き回し",
"WorkItems": [
"3. ①にCABLE を引き回す",
"■1. CABLE のRoHSﾏｰｸを確認する",
"2. CABLE にNOISE-FILTER を取付ける"
],
"WorkPoints": [
"LAN1"
],
"Tolks": [],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:ﾌｪﾗｲﾄｺｱ"
],
"WorkTypes": [],
"Words": [
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"60㎜",
"検査表①:CPU BOX確認",
"検査表①:CPU BOX確認"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "LANｹｰﾌﾞﾙ引き回し",
"WorkItems": [
"3. ①にCABLE を引き回す",
"■1. CABLE のRoHSﾏｰｸを確認する",
"2. CABLE にNOISE-FILTER を取付ける"
],
"WorkPoints": [
"LAN1"
],
"Tolks": [],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:CPU BOX確認",
"検査表①:CPU BOX確認"
],
"WorkTypes": [],
"Words": [
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"60㎜",
"検査表①:ﾌｪﾗｲﾄｺｱ",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "照明配線引き回し",
"WorkItems": [
"1. ①に照明配線を下から上面ﾌﾟﾚｰﾄまで引き回し､接続する"
],
"WorkPoints": [
"1CN0E001R"
],
"Tolks": [],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ"
],
"WorkTypes": [],
"Words": [
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "150cN･m",
"WorkName": "CP~MC-Sﾕﾆｯﾄ引き回し",
"WorkItems": [
"2. CABLE を引き回し､MC-Sへ接続する",
"■1. ①のCPにCABLE を接続する"
],
"WorkPoints": [
"4aF102",
"2aF102",
"CN1K307"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ"
],
"WorkTypes": [],
"Words": [
"検査表①:接続ﾁｪｯｸ ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ",
"検査表①:接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CP~MC-Sﾕﾆｯﾄ引き回し",
"WorkItems": [
"2. CABLE を引き回し､MC-Sへ接続する",
"■1. ①のCPにCABLE を接続する"
],
"WorkPoints": [
"4aF102",
"2aF102",
"CN1K307"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:接続ﾁｪｯｸ ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ"
],
"WorkTypes": [],
"Words": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"検査表①:接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "FG配線引き回し",
"WorkItems": [
"■1. ①にCABLE をSCREW で固定する"
],
"WorkPoints": [
"FGF1",
"FGK",
"横から見た図"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ"
],
"WorkTypes": [],
"Words": [
"検査表①:接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FG配線引き回し",
"WorkItems": [
"■1. ①にCABLE をSCREW で固定する"
],
"WorkPoints": [
"FGF1",
"FGK",
"横から見た図"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ"
],
"WorkTypes": [],
"Words": [
"検査表①:ﾈｼﾞ締めﾄﾙｸ",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｴﾝｺｰﾀﾞ配線引き回し",
"WorkItems": [
"1. ①にCABLE を引き回し､接続する"
],
"WorkPoints": [
"CN2K302",
"CN2K307",
"ｶﾁｯと音がするまで差込む事"
],
"Tolks": [],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ"
],
"WorkTypes": [],
"Words": [
"検査表①:ｴﾝｺｰﾀﾞ中継基板",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｪﾗｲﾄｺｱ取付",
"WorkItems": [
"■1. NOISE-FILTER ､FILTER の型式を確認する",
"2. ①にNOISE-FILTER FILTER を取付ける",
"3. ﾌｪﾗｲﾄｺｱがずれない様にｲﾝｼｭﾛｯｸで固定する(3箇所)",
"4. LED照明配線のﾌｪﾗｲﾄｺｱとLANｹｰﾌﾞﾙのﾌｪﾗｲﾄｺｱをｲﾝｼｭﾛｯｸで固定する"
],
"WorkPoints": [
"ｶﾁｯと音がするまで差込む事",
"型式",
"LED照明配線",
"型式",
"抜き窓から100mmの位置",
"ｲﾝｼｭﾛｯｸから50mmの位置",
"ｲﾝｼｭﾛｯｸから10mmの位置",
"ｴﾝｺｰﾀﾞ配線",
"AC配線"
],
"Tolks": [],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:ﾌｪﾗｲﾄｺｱの確認",
"100㎜",
"50㎜",
"10㎜",
"2LC-JG-23015"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｪﾗｲﾄｺｱ取付",
"WorkItems": [
"■1. NOISE-FILTER ､FILTER の型式を確認する",
"2. ①にNOISE-FILTER FILTER を取付ける",
"3. ﾌｪﾗｲﾄｺｱがずれない様にｲﾝｼｭﾛｯｸで固定する(3箇所)"
],
"WorkPoints": [
"ｶﾁｯと音がするまで差込む事",
"型式",
"LED照明配線",
"型式",
"抜き窓から100mmの位置",
"ｲﾝｼｭﾛｯｸから50mmの位置",
"ｲﾝｼｭﾛｯｸから10mmの位置",
"ｴﾝｺｰﾀﾞ配線",
"AC配線"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:型式･検査書ﾁｪｯｸ",
"検査表①:ﾌｪﾗｲﾄｺｱの確認",
"■安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "-ﾋﾞｯﾄ3㎜",
"ToolOther": "15cN･m",
"WorkName": "ｶﾒﾗ配線引き回し",
"WorkItems": [
"1. ①にCABLE を引き回し､接続する",
"2. CABLE にLABEL を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ"
],
"WorkTypes": [],
"Words": [
"検査表①:CPU BOX確認",
"LABEL の端面を当てて固定する"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗ配線引き回し",
"WorkItems": [
"1. ①にCABLE を引き回し､接続する",
"2. CABLE にLABEL を取付ける"
],
"WorkPoints": [
"CN2K307",
"CN2K303",
"ｶﾁｯと音がするまで差込む事",
"余長は下図のように引き回す",
"CAMERAのﾗﾍﾞﾙがある方を接続する"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "2LC-JG-23015",
"InspectionItems": [
"検査表①:CPU BOX確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ",
"LABEL の端面を当てて固定する",
"2LC-JG-23015"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23015",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "MC-Sｶﾊﾞｰ取付",
"WorkItems": [
"1. ①にCOVER をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け-①",
"WorkItems": [
"1. COVER の内側にLABEL を貼付ける"
],
"WorkPoints": [
"貼付箇所を㉖で脱脂してから貼付ける事",
"寸法や方向に注意して貼付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"内側",
"内側"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "背面ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①に②をBOLT BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": []
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.