input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "P013ﾋﾟﾝ圧入",
"WorkItems": [
"◆1. BLOCK のﾊﾞﾘ､打痕を確認",
"2. 1完成品にPIN を2か所圧入"
],
"WorkPoints": [
"保護ﾒｶﾞﾈ着用",
"ﾋﾟﾝはﾃｰﾊﾟｰ側を圧入 ※略図青丸部分",
"ﾋﾟﾝ出代=2mm±0.2mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIte... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ、打痕無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "P013ﾋﾟﾝ圧入",
"WorkItems": [
"◆1. BLOCK のﾊﾞﾘ､打痕を確認",
"2. 1完成品にPIN を2か所圧入"
],
"WorkPoints": [
"保護ﾒｶﾞﾈ着用",
"ﾋﾟﾝはﾃｰﾊﾟｰ側を圧入 ※略図青丸部分",
"ﾋﾟﾝ出代=2mm±0.2mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionI... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "指示寸法各±0.2㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝ圧入ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6099",
"WorkName": "P013ﾋﾟﾝ圧入",
"WorkItems": [
"◆1. BLOCK のﾊﾞﾘ､打痕を確認",
"2. 1完成品にPIN を2か所圧入"
],
"WorkPoints": [
"保護ﾒｶﾞﾈ着用",
"ﾋﾟﾝはﾃｰﾊﾟｰ側を圧入 ※略図青丸部分",
"ﾋﾟﾝ出代=2mm±0.2mm"
],
"Tolks": [],
"InspectionNo": "",
"Ins... | {
"QualityItem": "寸法確認",
"ToolManageNo": "FM-6099",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.2㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "A006ﾋﾟﾝ圧入",
"WorkItems": [
"◆1. PLATE のﾊﾞﾘ､打痕を確認",
"2. 1完成品にSPRING-PIN を圧入(3本)"
],
"WorkPoints": [
"保護ﾒｶﾞﾈ着用",
"Sﾋﾟﾝ出代=4.0mm±0.2mm",
"【注意】 Sﾋﾟﾝの割りの方向に注意 ※略図参照"
],
"Tolks": [],
"InspectionNo": "",
... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ、打痕無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "A006ﾋﾟﾝ圧入",
"WorkItems": [
"◆1. PLATE のﾊﾞﾘ､打痕を確認",
"2. 1完成品にSPRING-PIN を圧入(3本)",
"3. 2完成品にPIN を圧入"
],
"WorkPoints": [
"保護ﾒｶﾞﾈ着用",
"Sﾋﾟﾝ出代=4.0mm±0.2mm",
"【注意】 Sﾋﾟﾝの割りの方向に注意 ※略図参照",
"Sﾋﾟﾝ出代=3.0mm±0.... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "指示寸法各±0.2㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝ圧入ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6099",
"WorkName": "A006ﾋﾟﾝ圧入",
"WorkItems": [
"◆1. PLATE のﾊﾞﾘ､打痕を確認",
"2. 1完成品にSPRING-PIN を圧入(3本)",
"3. 2完成品にPIN を圧入"
],
"WorkPoints": [
"保護ﾒｶﾞﾈ着用",
"Sﾋﾟﾝ出代=4.0mm±0.2mm",
"【注意】 Sﾋﾟﾝの割りの方向に注意 ※略図参照",
"Sﾋﾟﾝ出代=... | {
"QualityItem": "寸法確認",
"ToolManageNo": "FM-6099",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.2㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "A006組立",
"WorkItems": [
"1. BRACKET のﾊﾞﾘの確認",
"2. ①にBRACKET をBOLT にて取付",
"3. 2完成品にBOLT NUT WASHER を取付"
],
"WorkPoints": [
"BRACKET は黄色矢印方向に押し当てにて取付",
"BRACKET は目視にて①と傾きなく取付"
],
"Tolks": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "2.0N･m",
"WorkName": "A006組立",
"WorkItems": [
"1. BRACKET のﾊﾞﾘの確認",
"2. ①にBRACKET をBOLT にて取付",
"3. 2完成品にBOLT NUT WASHER を取付"
],
"WorkPoints": [
"BRACKET は黄色矢印方向に押し当てにて取付",
"BRACKET は目視にて①と傾きなく取付"
],
"Tolks": [
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "A006組立",
"WorkItems": [
"1. BRACKET のﾊﾞﾘの確認",
"2. ①にBRACKET をBOLT にて取付",
"3. 2完成品にBOLT NUT WASHER を取付"
],
"WorkPoints": [
"BRACKET は黄色矢印方向に押し当てにて取付",
"BRACKET は目視にて①と傾きなく取付"
],
"Tolks": [
"締付ﾄﾙｸ ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "38.7±0.1㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾎﾞﾙﾄ高さ調節ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6105",
"WorkName": "A006組立",
"WorkItems": [
"1. BRACKET のﾊﾞﾘの確認",
"2. ①にBRACKET をBOLT にて取付",
"3. 2完成品にBOLT NUT WASHER を取付"
],
"WorkPoints": [
"BRACKET は黄色矢印方向に押し当てにて取付",
"BRACKET は目視にて①と傾きなく取付"
],
"Tolks": [
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "FM-6105",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "38.7±0.1㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "A006組立",
"WorkItems": [
"1. BRACKET のﾊﾞﾘの確認",
"2. ①にBRACKET をBOLT にて取付",
"3. 2完成品にBOLT NUT WASHER を取付"
],
"WorkPoints": [
"BRACKET は黄色矢印方向に押し当てにて取付",
"BRACKET は目視にて①と傾きなく取付"
],
"Tolks": [
"... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.2㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ部組立1/2",
"WorkItems": [
"◆1. BLOCK BRACKET のﾊﾞﾘ､打痕の確認"
],
"WorkPoints": [
"保護ﾒｶﾞﾈ着用"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ、打痕無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ部組立1/2",
"WorkItems": [
"2. 1完成品にBRACKET をBOLT WASHER にて取付"
],
"WorkPoints": [
"目視にてBLOCK と傾きなく取付"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ部組立1/2",
"WorkItems": [
"◆3. SPRING の両端にｸﾞﾘｰｽ塗布",
"2. 1完成品にBRACKET をBOLT WASHER にて取付",
"4. 2完成品に､3完成品をPIN にて取付",
"◆1. BLOCK BRACKET のﾊﾞﾘ､打痕の確認"
],
"WorkPoints": [
"保護ﾒｶﾞﾈ着用",
"目視にてBLOCK と傾きなく取付",
... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ部組立2/2",
"WorkItems": [
"◆1. BLOCK のﾊﾞﾘ､打痕の確認",
"2. ①のｽﾌﾟﾘﾝｸﾞをPIN にて1完成品に取付"
],
"WorkPoints": [
"保護ﾒｶﾞﾈ着用",
"【注意】 略図の方向から圧入",
"ｽﾌﾟﾘﾝｸﾞのﾌｯｸ部分をBLOCK に挿入後､PIN を圧入",
"PIN の溝部分にﾌｯｸを掛ける",
"PIN の... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ、打痕無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ部取付",
"WorkItems": [
"1. ①に②をBOLT にて取付"
],
"WorkPoints": [
"①の当てつけ面に隙間のない様に取付 ※下略図､青線部分"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ部取付",
"WorkItems": [
"2. 当付け面の隙間確認 ※略図青線部分"
],
"WorkPoints": [
"当付け面の隙間を確認 ※青線部分",
"隙間 0.03mm以内"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜以内",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "1.5N･m",
"WorkName": "A010ｼﾘﾝﾀﾞｰ組立1/4",
"WorkItems": [
"1. ⑥に①を取付",
"2. 1完成品のｵｰﾄSWの止めねじを②と交換する ※2か所",
"3. 2完成品に㉚のエアー供給ユニットを接続し、エアーを供給する",
"4. ｼﾘﾝﾀﾞｰ【開】状態の⑦ｵｰﾄSW調整"
],
"WorkPoints": [
"交換した止めねじは廃棄する",
"ｵｰﾄSWの合わせ方参照",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.27㎜",
"ToolOther": "10cN･m",
"WorkName": "A010ｼﾘﾝﾀﾞｰ組立1/4",
"WorkItems": [
"1. ⑥に①を取付",
"2. 1完成品のｵｰﾄSWの止めねじを②と交換する ※2か所",
"3. 2完成品に㉚のエアー供給ユニットを接続し、エアーを供給する",
"4. ｼﾘﾝﾀﾞｰ【開】状態の⑦ｵｰﾄSW調整"
],
"WorkPoints": [
"交換した止めねじは廃棄する",
"ｵｰﾄSWの合わせ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｵｰﾄSW位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4292",
"WorkName": "A010ｼﾘﾝﾀﾞｰ組立1/4",
"WorkItems": [
"1. ⑥に①を取付",
"2. 1完成品のｵｰﾄSWの止めねじを②と交換する ※2か所",
"3. 2完成品に㉚のエアー供給ユニットを接続し、エアーを供給する",
"4. ｼﾘﾝﾀﾞｰ【開】状態の⑦ｵｰﾄSW調整"
],
"WorkPoints": [
"交換した止めねじは廃棄する",
"ｵｰﾄSWの合わせ方... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4292",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｵｰﾄSWがON(LED点灯)になる事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ(共通)",
"Size": "",
"ToolOther": "FM-3418",
"WorkName": "A010ｼﾘﾝﾀﾞｰ組立1/4",
"WorkItems": [
"1. ⑥に①を取付",
"2. 1完成品のｵｰﾄSWの止めねじを②と交換する ※2か所",
"3. 2完成品に㉚のエアー供給ユニットを接続し、エアーを供給する",
"4. ｼﾘﾝﾀﾞｰ【開】状態の⑦ｵｰﾄSW調整"
],
"WorkPoints": [
"交換した止めねじは廃棄する",
"ｵｰﾄSWの合わせ方参照... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-3418",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｵｰﾄSWがON(LED点灯)になる事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ(2､8､11)",
"Size": "",
"ToolOther": "FM-6114",
"WorkName": "A010ｼﾘﾝﾀﾞｰ組立1/4",
"WorkItems": [
"1. ⑥に①を取付",
"2. 1完成品のｵｰﾄSWの止めねじを②と交換する ※2か所",
"3. 2完成品に㉚のエアー供給ユニットを接続し、エアーを供給する",
"4. ｼﾘﾝﾀﾞｰ【開】状態の⑦ｵｰﾄSW調整"
],
"WorkPoints": [
"交換した止めねじは廃棄する",
"ｵｰﾄSW... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-6114",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｵｰﾄSWがON(LED点灯)になる事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "A010ｼﾘﾝﾀﾞｰ組立2/4",
"WorkItems": [
"1. ①配線の指定寸法にﾏｰｷﾝｸﾞ実施"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"220mm",
"【B106P】",
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "63cN･m",
"WorkName": "A010ｼﾘﾝﾀﾞｰ組立3/4",
"WorkItems": [
"1. BRACKET BRACKET のﾊﾞﾘ､打痕を確認",
"2. ①にBRACKET BRACKET をBOLT にて仮取付",
"3. ㉙エアー供給ユニットを接続",
"4. 2完成品BRACKET BRACKET の取付調整"
],
"WorkPoints": [
"青色矢印部分に接続 ※ｴｱｰはまだ供給しな... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "63cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｵｰﾄSW位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4292",
"WorkName": "A010ｼﾘﾝﾀﾞｰ組立3/4",
"WorkItems": [
"1. BRACKET BRACKET のﾊﾞﾘ､打痕を確認",
"2. ①にBRACKET BRACKET をBOLT にて仮取付",
"3. ㉙エアー供給ユニットを接続",
"4. 2完成品BRACKET BRACKET の取付調整",
"1. BRACKET BRACKET のﾊﾞﾘ､打痕を確認",
"2. ①にBR... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4292",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ(2､8､11)",
"Size": "",
"ToolOther": "FM-6114",
"WorkName": "A010ｼﾘﾝﾀﾞｰ組立3/4",
"WorkItems": [
"1. BRACKET BRACKET のﾊﾞﾘ､打痕を確認",
"2. ①にBRACKET BRACKET をBOLT にて仮取付",
"3. ㉙エアー供給ユニットを接続",
"4. 2完成品BRACKET BRACKET の取付調整"
],
"WorkPoints": [
"青色矢印部分に接続 ※ｴｱｰはま... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6114",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "A010ｼﾘﾝﾀﾞｰ組立4/4",
"WorkItems": [
"1. ①にCABLE-SUPPORT BOLT を2か所取付",
"2. 1完成品の配線を結束"
],
"WorkPoints": [
"緑丸部は1本で結束の事",
"黄丸部のﾏｰｷﾝｸﾞが揃っていることを確認後､結束",
"ｲﾝｼｭﾛｯｸから90mmのﾏｰｷﾝｸﾞが揃っている事"
],
"Tolks":... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "A010ｼﾘﾝﾀﾞｰ組立4/4",
"WorkItems": [
"1. ①にCABLE-SUPPORT BOLT を2か所取付",
"2. 1完成品の配線を結束"
],
"WorkPoints": [
"緑丸部は1本で結束の事",
"黄丸部のﾏｰｷﾝｸﾞが揃っていることを確認後､結束",
"ｲﾝｼｭﾛｯｸから90mmのﾏｰｷﾝｸﾞが揃っている事"
],
"Tolks": [
"締付ﾄﾙ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "P001ﾌﾟﾚｰﾄ組立",
"WorkItems": [
"1. PLATE のﾊﾞﾘ､打痕を確認",
"▲2. SCREW に㉘塗布後、1完成品に4か所取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"◆作業者安全作業",
"●... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ、打痕無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程",
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "P001ﾌﾟﾚｰﾄ組立",
"WorkItems": [
"1. PLATE のﾊﾞﾘ､打痕を確認",
"3. SCREW の出代調整",
"▲2. SCREW に㉘塗布後、1完成品に4か所取付"
],
"WorkPoints": [
"SCREW をねじ込み､板裏出代1mm±0.1mmに取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "P001ﾌﾟﾚｰﾄ組立",
"WorkItems": [
"3. SCREW の出代調整"
],
"WorkPoints": [
"SCREW をねじ込み､板裏出代1mm±0.1mmに取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "1.0±0.1㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "1.5N･m",
"WorkName": "ｴｱｽﾗｲﾄﾞ組立1/8",
"WorkItems": [],
"WorkPoints": [
"仮止め:SD-A040344-038にて調整"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｴｱｽﾗｲﾄﾞ組立1/8",
"WorkItems": [
"1. AIR-SLIDE のｵｰﾄSWのﾄﾒﾈｼﾞをSCREW と交換する ※2か所",
"2. おおむね略図の位置にｵｰﾄSWを仮取付",
"3. 2完成品にSPEED-CONTROLLER を2か所取付",
"4. SPEED-CONTROLLER ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ調整"
],
"WorkPoints": [
"仮止め:SD-A040344-038... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りの回転数で調整の事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "ｴｱｽﾗｲﾄﾞ組立2/8",
"WorkItems": [
"1. ①にBRACKET をBOLT にて取付"
],
"WorkPoints": [
"取付寸法=略図参照",
"①とBRACKET の端面を揃える"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wor... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱｽﾗｲﾄﾞ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5980",
"WorkName": "ｴｱｽﾗｲﾄﾞ組立2/8",
"WorkItems": [
"1. ①にBRACKET をBOLT にて取付"
],
"WorkPoints": [
"取付寸法=略図参照",
"①とBRACKET の端面を揃える"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5980",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｴｱｽﾗｲﾄﾞ組立2/8",
"WorkItems": [
"2. 取付寸法確認"
],
"WorkPoints": [
"1完成品の取付位置寸法を確認",
"取付位置寸法:37.1㎜±0.1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "37.1±0.1㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "194cN･m",
"WorkName": "ｴｱｽﾗｲﾄﾞ組立3/8",
"WorkItems": [
"1. ①に②をBOLT にて取付",
"2. 隙間､及び干渉確認 ※略図青線部分"
],
"WorkPoints": [
"Sﾋﾟﾝ(3点)との間に隙間のない様に取付",
"Sﾋﾟﾝ当付け面の隙間を確認 ※青線部分"
],
"Tolks": [],
"InspectionNo": "",
"InspectionIt... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ｴｱｽﾗｲﾄﾞ組立3/8",
"WorkItems": [],
"WorkPoints": [
"各隙間 0.03mm以内",
"【目視確認】 ﾌﾞﾗｹｯﾄU溝部分とﾎﾞﾙﾄの干渉が無い事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜以内",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｴｱｽﾗｲﾄﾞ組立4/8",
"WorkItems": [
"1. ①に②をBOLT にて取付"
],
"WorkPoints": [
"②上辺に隙間のない様に取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ｴｱｽﾗｲﾄﾞ組立4/8",
"WorkItems": [
"2. 隙間確認 ※略図青線部分"
],
"WorkPoints": [
"当付け面の隙間を確認 ※青線部分",
"各隙間 0.03mm以内"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜以内",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "63cN･m",
"WorkName": "ｴｱｽﾗｲﾄﾞ組立5/8",
"WorkItems": [
"1. ①に②を付属ﾎﾞﾙﾄにて取付",
"2. 1完成品のﾊﾞﾘを確認する"
],
"WorkPoints": [
"②の取付穴はｼﾘﾝﾀﾞｰを開状態にすると現れる ※黄色矢印方向",
"②は①の基準ﾋﾟﾝに嵌合させて取付",
"付属ﾎﾞﾙﾄ M3×20 2本"
],
"Tolks": [
"締付ﾄﾙｸ... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "63cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｴｱｽﾗｲﾄﾞ組立5/8",
"WorkItems": [
"1. ①に②を付属ﾎﾞﾙﾄにて取付",
"2. 1完成品のﾊﾞﾘを確認する"
],
"WorkPoints": [
"②の取付穴はｼﾘﾝﾀﾞｰを開状態にすると現れる ※黄色矢印方向",
"②は①の基準ﾋﾟﾝに嵌合させて取付",
"付属ﾎﾞﾙﾄ M3×20 2本"
],
"Tolks": [
"締付ﾄﾙｸ 63cN･m"
],
"... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘが無い事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｴｱｽﾗｲﾄﾞ組立6/8",
"WorkItems": [
"1. ①に②をBOLT にて仮取付"
],
"WorkPoints": [
"仮止め:SD-A040344-063にて本締め"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｵｰﾄSW位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4292",
"WorkName": "ｴｱｽﾗｲﾄﾞ組立7/8",
"WorkItems": [
"1. ①のｵｰﾄSW調整"
],
"WorkPoints": [
"点灯した位置でﾏｰｷﾝｸﾞ",
"消灯した位置でﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ中央に取付",
"㉖エアー供給ユニットより、青色矢印側にエアを供給 【0.5Mpa】",
"青丸部分のSWを調整",
"㉖エアー供給ユニットより、黄色矢印側に... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4292",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｵｰﾄSWがON(LED点灯)になる事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ(共通)",
"Size": "",
"ToolOther": "FM-3418",
"WorkName": "ｴｱｽﾗｲﾄﾞ組立7/8",
"WorkItems": [
"1. ①のｵｰﾄSW調整"
],
"WorkPoints": [
"点灯した位置でﾏｰｷﾝｸﾞ",
"消灯した位置でﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ中央に取付",
"㉖エアー供給ユニットより、青色矢印側にエアを供給 【0.5Mpa】",
"青丸部分のSWを調整",
"㉖エアー供給ユニットより、黄色矢印側にエア... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-3418",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｵｰﾄSWがON(LED点灯)になる事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.27㎜",
"ToolOther": "10cN･m",
"WorkName": "ｴｱｽﾗｲﾄﾞ組立7/8",
"WorkItems": [
"1. ①のｵｰﾄSW調整"
],
"WorkPoints": [
"点灯した位置でﾏｰｷﾝｸﾞ",
"消灯した位置でﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ中央に取付",
"㉖エアー供給ユニットより、青色矢印側にエアを供給 【0.5Mpa】",
"青丸部分のSWを調整",
"㉖エアー供給ユニットより、黄色矢印側... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｴｱｽﾗｲﾄﾞ組立8/8",
"WorkItems": [
"1. ①のｵｰﾄSW配線にﾏｰｷﾝｸﾞ実施"
],
"WorkPoints": [
"指定寸法にてﾏｰｷﾝｸﾞ実施 ※略図参照"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "1.5N･m",
"WorkName": "清掃部ｴｱｽﾗｲﾄﾞ組立1/2",
"WorkItems": [
"3. 2完成品にSPEED-CONTROLLER を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "清掃部ｴｱｽﾗｲﾄﾞ組立1/2",
"WorkItems": [
"1. AIR-SLIDE のｵｰﾄSWのﾄﾒﾈｼﾞをSCREW と交換する",
"2. ｵｰﾄSWを仮取付",
"3. 2完成品にSPEED-CONTROLLER を取付",
"4. ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ調整"
],
"WorkPoints": [
"おおむね略図の位置に仮取付",
"仮止め:SD-A040344-056にて調整"
]... | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りの回転数で調整の事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "清掃部ｴｱｽﾗｲﾄﾞ組立2/2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"21.3±... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾗｹｯﾄ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5966",
"WorkName": "清掃部ｴｱｽﾗｲﾄﾞ組立2/2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"21.3±... | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5966",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "清掃部ｴｱｽﾗｲﾄﾞ組立2/2",
"WorkItems": [
"1. ①にBRACKET を指定寸法にてBOLT で取付",
"2. 取付寸法確認"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄはｼﾘﾝﾀﾞｰ端面に揃える ※緑線部分",
"㉘ジグを用いてシリンダー13.6mmの時に、ブラケット21.3mmに取付 ※略図参照",
"1完成品の取付位置寸法を確認",
"取付位置寸法①:21.... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "指示寸法各±0.1㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "清掃部組立",
"WorkItems": [
"1. ①に⑥をBOLT にて取付"
],
"WorkPoints": [
"⑥のSﾋﾟﾝに①を当てつけて取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "清掃部組立",
"WorkItems": [
"2. 隙間確認"
],
"WorkPoints": [
"Sﾋﾟﾝ当付け面の隙間を確認 ※青線部分"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜以内",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "1.5N･m",
"WorkName": "ﾛｯｸｼﾘﾝﾀﾞｰ組立",
"WorkItems": [
"1. CYLINDER にJOINT を取付",
"2. 1完成品のｵｰﾄSWのﾄﾒﾈｼﾞをSCREW と交換する",
"3. おおむね下略図の位置にｵｰﾄSWを仮取付",
"4. 3完成品にｴｱｰを供給 【0.5Mpa】",
"5. ｵｰﾄSW調整"
],
"WorkPoints": [
"行き限のみ調整 ※略図の状態"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.27㎜",
"ToolOther": "10cN･m",
"WorkName": "ﾛｯｸｼﾘﾝﾀﾞｰ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"検査表CYLINDE... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｵｰﾄSW位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4292",
"WorkName": "ﾛｯｸｼﾘﾝﾀﾞｰ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m",
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "WEPJ-G002-C19",
"InspectionItems": [
"検査表CYLINDER :ｵｰﾄSW検査 ﾛｯｸ部"
],
"WorkTypes... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4292",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｵｰﾄSWがON(LED点灯)になる事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ(共通)",
"Size": "",
"ToolOther": "FM-3418",
"WorkName": "ﾛｯｸｼﾘﾝﾀﾞｰ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"検査表CYLINDER :... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-3418",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｵｰﾄSWがON(LED点灯)になる事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "N030ﾋﾟﾝ圧入",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ、打痕無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝ圧入ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6099",
"WorkName": "N030ﾋﾟﾝ圧入",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6099",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "N030ﾋﾟﾝ圧入",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "2.0±0.2㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "N016ﾋﾟﾝ圧入",
"WorkItems": [
"1. HOOK のﾊﾞﾘ､打痕の確認"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ、打痕無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝ圧入ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6099",
"WorkName": "N016ﾋﾟﾝ圧入",
"WorkItems": [
"1. HOOK のﾊﾞﾘ､打痕の確認"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6099",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "N016ﾋﾟﾝ圧入",
"WorkItems": [
"1. HOOK のﾊﾞﾘ､打痕の確認"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "2.5~2.7㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "40cN･m",
"WorkName": "P615ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①にBRACKET をSCREW にて取付"
],
"WorkPoints": [
"①のﾋﾟﾝをBRACKET に嵌合させてSCREW を締結"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Wo... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚﾊﾞｰ取付",
"WorkItems": [
"2. ①にLEVER SPACER をPIN で取付",
"3. 2完成品にPIN を取付",
"1. LEVER のﾊﾞﾘを確認する"
],
"WorkPoints": [
"①とLEVER の間にSPACER を挿入",
"SPACER 挿入後､PIN で取付け",
"取付け後､動作確認"
],
"Tolks": [
"締付ﾄﾙｸ 40c... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘが無い事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5㎜",
"ToolOther": "60cN･m",
"WorkName": "ﾚﾊﾞｰ取付",
"WorkItems": [
"2. ①にLEVER SPACER をPIN で取付",
"1. LEVER のﾊﾞﾘを確認する"
],
"WorkPoints": [
"①とLEVER の間にSPACER を挿入",
"SPACER 挿入後､PIN で取付け",
"取付け後､動作確認"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5㎜",
"ToolOther": "40cN･m",
"WorkName": "ﾚﾊﾞｰ取付",
"WorkItems": [
"3. 2完成品にPIN を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words":... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "N004ﾊﾝﾄﾞﾙ取付",
"WorkItems": [
"1. BRACKET のﾊﾞﾘ､打痕確認",
"3. 2完成品にPIN 取付",
"2. 1完成品にGRIP をWASHER NUT にて取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"Inspec... | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ、打痕無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "6.0N･m",
"WorkName": "N004ﾊﾝﾄﾞﾙ取付",
"WorkItems": [
"1. BRACKET のﾊﾞﾘ､打痕確認",
"3. 2完成品にPIN 取付",
"2. 1完成品にGRIP をWASHER NUT にて取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5㎜",
"ToolOther": "40cN･m",
"WorkName": "N004ﾊﾝﾄﾞﾙ取付",
"WorkItems": [
"1. BRACKET のﾊﾞﾘ､打痕確認",
"3. 2完成品にPIN 取付",
"2. 1完成品にGRIP をWASHER NUT にて取付"
],
"WorkPoints": [
"短い側"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m",
"締付ﾄﾙｸ 6.0N･m"
],
"In... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "40cN･m",
"WorkName": "ﾚﾊﾞｰ部取付",
"WorkItems": [
"1. ①に②をSCREW で取付"
],
"WorkPoints": [
"ﾋﾟﾝを嵌合させてSCREW を締結"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業"... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線･配管取付",
"WorkItems": [
"1. ①にCABLE を接続",
"2. PLATE にCOUPLER をNUT で取付",
"3. 2完成品に④取付",
"4. 3完成品を1完成品に取付"
],
"WorkPoints": [
"取付後､配線/配管を略図青丸部分で揃える",
"確実に挿入する事"
],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m"
],
... | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "1.2N･m",
"WorkName": "配線･配管取付",
"WorkItems": [
"1. ①にCABLE を接続",
"2. PLATE にCOUPLER をNUT で取付",
"3. 2完成品に④取付",
"4. 3完成品を1完成品に取付"
],
"WorkPoints": [
"取付後､配線/配管を略図青丸部分で揃える",
"確実に挿入する事"
],
"Tolks": [
"締付ﾄﾙｸ 1.... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "40cN･m",
"WorkName": "ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ①に②をSCREW で取付"
],
"WorkPoints": [
"ﾋﾟﾝを嵌合させてSCREW を取付",
"配線配管を挟ま無い事"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTyp... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾌﾟﾘﾝｸﾞ取付",
"WorkItems": [
"◆1. ①にSPRING 取付",
"2. 1完成品にｶﾌﾟﾄﾝﾃｰﾌﾟ貼付"
],
"WorkPoints": [
"略図黄色矢印部分ﾃｰﾌﾟが配線被覆に食い込むように貼付",
"ﾃｰﾌﾟ幅:10mm/長さ:40mm",
"青丸枠段差部分にﾃｰﾌﾟを貼ら無い事",
"ｽﾌﾟﾘﾝｸﾞ両端にｸﾞﾘｰｽ塗布"
],
"Tolks": [],
"... | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｽﾌﾟﾘﾝｸﾞ取付",
"WorkItems": [
"2. 1完成品にｶﾌﾟﾄﾝﾃｰﾌﾟ貼付"
],
"WorkPoints": [
"略図黄色矢印部分ﾃｰﾌﾟが配線被覆に食い込むように貼付",
"ﾃｰﾌﾟ幅:10mm/長さ:40mm",
"青丸枠段差部分にﾃｰﾌﾟを貼ら無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": []... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "48cN･m",
"WorkName": "ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①にCOVER をSCREW SCREW で取付"
],
"WorkPoints": [
"全てのﾈｼﾞを均等に締付けながらCOVER を取付"
],
"Tolks": [
"締付ﾄﾙｸ 48cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "48cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "本体組立1/23",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "本体組立1/23",
"WorkItems": [
"1. ①に②をBOLT にて取付",
"2. 隙間確認"
],
"WorkPoints": [
"ﾋﾟﾝと段差に当てつけて取付",
"Sﾋﾟﾝ当付け面の隙間を確認 ※青線部分",
"段差の隙間を確認 ※黄色矢印部分が段差隙間部分",
"各隙間 0.03mm以内"
],
"Tolks": [],
"Inspect... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜以内",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "本体組立2/23",
"WorkItems": [
"1. ①に②をBOLT にて取付",
"2. 隙間確認"
],
"WorkPoints": [
"Sﾋﾟﾝ当付け面の隙間を確認※青線部分",
"ﾋﾟﾝに当付けて取付",
"M4厚ﾜｯｼｬの位置に注意 ※略図参照",
"各隙間 0.03mm以内"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "本体組立2/23",
"WorkItems": [
"1. ①に②をBOLT にて取付",
"2. 隙間確認"
],
"WorkPoints": [
"Sﾋﾟﾝ当付け面の隙間を確認※青線部分",
"ﾋﾟﾝに当付けて取付",
"M4厚ﾜｯｼｬの位置に注意 ※略図参照",
"各隙間 0.03mm以内"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
... | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜以内",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.27㎜",
"ToolOther": "10cN･m",
"WorkName": "本体組立3/23",
"WorkItems": [
"1. ①のｵｰﾄSW調整"
],
"WorkPoints": [
"点灯した位置でﾏｰｷﾝｸﾞ",
"消灯した位置でﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ中央に取付",
"㉘エアー供給ユニットより、戻り側接手にエアーを供給 ※青色矢印",
"ｴｱｰ供給圧【0.5Mpa】"
],
"Tolks": [
"締... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｵｰﾄSW位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4292",
"WorkName": "本体組立3/23",
"WorkItems": [
"1. ①のｵｰﾄSW調整"
],
"WorkPoints": [
"点灯した位置でﾏｰｷﾝｸﾞ",
"消灯した位置でﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ中央に取付",
"㉘エアー供給ユニットより、戻り側接手にエアーを供給 ※青色矢印",
"ｴｱｰ供給圧【0.5Mpa】"
],
"Tolks": [
"締付... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-4292",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｵｰﾄSWがON(LED点灯)になる事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ(共通)",
"Size": "",
"ToolOther": "FM-3418",
"WorkName": "本体組立3/23",
"WorkItems": [
"1. ①のｵｰﾄSW調整"
],
"WorkPoints": [
"点灯した位置でﾏｰｷﾝｸﾞ",
"消灯した位置でﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ中央に取付",
"㉘エアー供給ユニットより、戻り側接手にエアーを供給 ※青色矢印",
"ｴｱｰ供給圧【0.5Mpa】"
],
"Tolks": [
"締付ﾄﾙ... | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-3418",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｵｰﾄSWがON(LED点灯)になる事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "本体組立3/23",
"WorkItems": [
"2. 調整後､継手を傾ける",
"3. ｵｰﾄSW配線にﾏｰｷﾝｸﾞ実施"
],
"WorkPoints": [
"ｵｰﾄSWより60mmにﾏｰｷﾝｸﾞ実施"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
]... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "本体組立4/23",
"WorkItems": [
"2. ｴｱﾁｭｰﾌﾞにﾏｰｷﾝｸﾞ",
"3. ③ﾁｭｰﾌﾞにAﾎﾟｰﾄ識別ﾏｰｷﾝｸﾞ",
"1. ①に②③ｴｱﾁｭｰﾌﾞ接続"
],
"WorkPoints": [
"清掃部上昇 Aﾎﾟｰﾄ【行き】 ② 145mm",
"清掃部下降 Bﾎﾟｰﾄ【戻り】 ③ 175mm",
"② 145mm 先端より70mmにﾏｰｷﾝｸﾞ",
"③ ... | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体組立5/23",
"WorkItems": [
"2. 配線ﾏｰｷﾝｸﾞ位置で結束",
"3. ｴｱﾁｭｰﾌﾞどうしを結束",
"1. ①のｵｰﾄSW線引き回し ※略図青線部分"
],
"WorkPoints": [
"ｴｱﾁｭｰﾌﾞの下を通し､配線ﾏｰｷﾝｸﾞとﾀｲﾏｳﾝﾄを合わす",
"ｴｱﾁｭｰﾌﾞを省いて描いています",
"動作部分に干渉しない為の結束",
"配線を省いて描いています"
... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "20cN･m",
"WorkName": "本体組立6/23",
"WorkItems": [
"1. ①に②をBOLT WASHER にて仮取付"
],
"WorkPoints": [
"ﾎﾞﾙﾄ4本を均等に締付"
],
"Tolks": [
"締付ﾄﾙｸ 20cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "100cN･m",
"WorkName": "本体組立6/23",
"WorkItems": [
"2. ﾌﾟﾚｰﾄ部ｼﾘﾝﾀﾞｰを規正ﾋﾟﾝに当てつけて締結"
],
"WorkPoints": [
"目視にて隙間確認"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作... | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "定盤",
"Size": "",
"ToolOther": "",
"WorkName": "本体組立7/23",
"WorkItems": [
"1. ①のﾛｰﾄﾞｾﾙ高さ確認"
],
"WorkPoints": [
"ﾛｰﾄﾞｾﾙの中心部分で測定する事",
"保持ﾌﾞﾛｯｸ治具(11.4mm)は先端ﾋﾟﾝの保持に使用する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "定盤",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "本体組立7/23",
"WorkItems": [
"1. ①のﾛｰﾄﾞｾﾙ高さ確認"
],
"WorkPoints": [
"ﾛｰﾄﾞｾﾙの中心部分で測定する事",
"保持ﾌﾞﾛｯｸ治具(11.4mm)は先端ﾋﾟﾝの保持に使用する"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C19",
"InspectionItems": [
"... | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "127.8±0.2㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "保持ﾌﾞﾛｯｸ",
"Size": "",
"ToolOther": "FM-5969",
"WorkName": "本体組立7/23",
"WorkItems": [
"1. ①のﾛｰﾄﾞｾﾙ高さ確認"
],
"WorkPoints": [
"ﾛｰﾄﾞｾﾙの中心部分で測定する事",
"保持ﾌﾞﾛｯｸ治具(11.4mm)は先端ﾋﾟﾝの保持に使用する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "高さ確認",
"ToolManageNo": "FM-5969",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "127.8±0.2㎜",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "127.8㎜",
"ToolOther": "",
"WorkName": "本体組立7/23",
"WorkItems": [
"1. ①のﾛｰﾄﾞｾﾙ高さ確認"
],
"WorkPoints": [
"ﾛｰﾄﾞｾﾙの中心部分で測定する事",
"保持ﾌﾞﾛｯｸ治具(11.4mm)は先端ﾋﾟﾝの保持に使用する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
... | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "127.8±0.2㎜",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "定盤",
"Size": "",
"ToolOther": "",
"WorkName": "本体組立8/23",
"WorkItems": [
"2. 清掃部高さ確認",
"1. ①の清掃部上昇"
],
"WorkPoints": [
"各規格値Ⓐ：9.6mm ＋0.2mm ｰ0.3mmⒷ：8.1mm ＋0.2mm ｰ0.3mm",
"㉖エアー供給ユニットより、上昇（Aポート）に0.5Mpaのエアーを供給",
"前ページの同様、㉙保持ブロック治具... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "定盤",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "本体組立8/23",
"WorkItems": [
"2. 清掃部高さ確認",
"1. ①の清掃部上昇"
],
"WorkPoints": [
"各規格値Ⓐ：9.6mm ＋0.2mm ｰ0.3mmⒷ：8.1mm ＋0.2mm ｰ0.3mm",
"㉖エアー供給ユニットより、上昇（Aポート）に0.5Mpaのエアーを供給",
"前... | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "A:9.6+0.2㎜9.6-0.3㎜B:8.1+0.2㎜8.1-0.3㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｵｰﾄSW位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4292",
"WorkName": "本体組立8/23",
"WorkItems": [
"2. 清掃部高さ確認",
"1. ①の清掃部上昇",
"2. 清掃部高さ確認",
"1. ①の清掃部上昇"
],
"WorkPoints": [
"各規格値Ⓐ：9.6mm ＋0.2mm ｰ0.3mmⒷ：8.1mm ＋0.2mm ｰ0.3mm",
"㉖エアー供... | {
"QualityItem": "高さ確認",
"ToolManageNo": "FM-4292",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "A:9.6+0.2㎜9.6-0.3㎜B:8.1+0.2㎜8.1-0.3㎜",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "保持ﾌﾞﾛｯｸ",
"Size": "",
"ToolOther": "FM-5969",
"WorkName": "本体組立8/23",
"WorkItems": [
"2. 清掃部高さ確認",
"1. ①の清掃部上昇"
],
"WorkPoints": [
"各規格値Ⓐ：9.6mm ＋0.2mm ｰ0.3mmⒷ：8.1mm ＋0.2mm ｰ0.3mm",
"㉖エアー供給ユニットより、上昇（Aポート）に0.5Mpaのエアーを供給",
"前ページの... | {
"QualityItem": "高さ確認",
"ToolManageNo": "FM-5969",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "A:9.6+0.2㎜9.6-0.3㎜B:8.1+0.2㎜8.1-0.3㎜",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "上昇高さ確認ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5967",
"WorkName": "本体組立8/23",
"WorkItems": [
"2. 清掃部高さ確認",
"1. ①の清掃部上昇"
],
"WorkPoints": [
"各規格値Ⓐ：9.6mm ＋0.2mm ｰ0.3mmⒷ：8.1mm ＋0.2mm ｰ0.3mm",
"㉖エアー供給ユニットより、上昇（Aポート）に0.5Mpaのエアーを供給",
"前ペ... | {
"QualityItem": "高さ確認",
"ToolManageNo": "FM-5967",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "A:9.6+0.2㎜9.6-0.3㎜B:8.1+0.2㎜8.1-0.3㎜",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C19",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "定盤",
"Size": "",
"ToolOther": "",
"WorkName": "本体組立9/23",
"WorkItems": [
"3. 調整後､赤丸部締結",
"4. 最終確認"
],
"WorkPoints": [
"ロードセル上面を基準にして、測定箇所に㉚ブロックゲージを設置して比較測定する",
"青丸はすべて着座していることを確認",
"手順2同様に平面度を確認"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo"... | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付け出来ている事",
"Method": "定盤",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.